9 years agoUSB: io_ti: fix firmware download on big-endian machines
Johan Hovold [Fri, 25 Apr 2014 13:23:03 +0000 (15:23 +0200)]
USB: io_ti: fix firmware download on big-endian machines

commit 5509076d1b4485ce9fb07705fcbcd2695907ab5b upstream.

During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.

Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.

Reported-by: Ludovic Drolez <>
Tested-by: Ludovic Drolez <>
Signed-off-by: Johan Hovold <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
9 years agousb/xhci: fix compilation warning when !CONFIG_PCI && !CONFIG_PM
David Cohen [Fri, 25 Apr 2014 16:20:16 +0000 (19:20 +0300)]
usb/xhci: fix compilation warning when !CONFIG_PCI && !CONFIG_PM

commit 01bb59ebffdec314da8da66266edf29529372f9b upstream.

When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]

Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.

This warning has been in since 3.2 kernel and was
caused by commit 421aa841a134f6a743111cf44d0c6d3b45e3cf8c
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried

Signed-off-by: David Cohen <>
Signed-off-by: Mathias Nyman <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
9 years agousb: xhci: Prefer endpoint context dequeue pointer over stopped_trb
Julius Werner [Fri, 25 Apr 2014 16:20:13 +0000 (19:20 +0300)]
usb: xhci: Prefer endpoint context dequeue pointer over stopped_trb

commit 1f81b6d22a5980955b01e08cf27fb745dc9b686f upstream.

We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.

The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.

This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.

This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae636747146ea97efa18e04576acd3416e2514f5 "USB: xhci: URB
cancellation support."

Signed-off-by: Julius Werner <>
Signed-off-by: Mathias Nyman <>
Signed-off-by: Greg Kroah-Hartman <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoxhci: For streams the css flag most be read from the stream-ctx on ep stop
Hans de Goede [Thu, 3 Oct 2013 22:29:47 +0000 (00:29 +0200)]
xhci: For streams the css flag most be read from the stream-ctx on ep stop

commit c4bedb77ec4cb42f37cae4cbfddda8283161f7c8 upstream.

Signed-off-by: Hans de Goede <>
Signed-off-by: Sarah Sharp <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoBtrfs: fix inode caching vs tree log
Miao Xie [Wed, 23 Apr 2014 11:33:36 +0000 (19:33 +0800)]
Btrfs: fix inode caching vs tree log

commit 1c70d8fb4dfa95bee491816b2a6767b5ca1080e7 upstream.

Currently, with inode cache enabled, we will reuse its inode id immediately
after unlinking file, we may hit something like following:

|->iput inode
|->return inode id into inode cache
|->create dir,fsync
|->power off

An easy way to reproduce this problem is:

mkfs.btrfs -f /dev/sdb
mount /dev/sdb /mnt -o inode_cache,commit=100
dd if=/dev/zero of=/mnt/data bs=1M count=10 oflag=sync
inode_id=`ls -i /mnt/data | awk '{print $1}'`
rm -f /mnt/data

while [ 1 ]
        mkdir /mnt/dir_$i
        test1=`stat /mnt/dir_$i | grep Inode: | awk '{print $4}'`
        if [ $test1 -eq $inode_id ]
dd if=/dev/zero of=/mnt/dir_$i/data bs=1M count=1 oflag=sync
echo b > /proc/sysrq-trigger
sleep 1

mount /dev/sdb /mnt
umount /dev/sdb
btrfs check /dev/sdb

We fix this problem by adding unlinked inode's id into pinned tree,
and we can not reuse them until committing transaction.

Signed-off-by: Miao Xie <>
Signed-off-by: Wang Shilong <>
Signed-off-by: Chris Mason <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoBtrfs: Don't allocate inode that is already in use
Stefan Behrens [Tue, 15 Oct 2013 18:08:15 +0000 (20:08 +0200)]
Btrfs: Don't allocate inode that is already in use

commit ff76b0565523319d7c1c0b51d5a5a8915d33efab upstream.

Due to an off-by-one error, it is possible to reproduce a bug
when the inode cache is used.

The same inode number is assigned twice, the second time this
leads to an EEXIST in btrfs_insert_empty_items().

The issue can happen when a file is removed right after a subvolume
is created and then a new inode number is created before the
inodes in free_inode_pinned are processed.
unlink() calls btrfs_return_ino() which calls start_caching() in this
case which adds [highest_ino + 1, BTRFS_LAST_FREE_OBJECTID] by
searching for the highest inode (which already cannot find the
unlinked one anymore in btrfs_find_free_objectid()). So if this
unlinked inode's number is equal to the highest_ino + 1 (or >= this value
instead of > this value which was the off-by-one error), we mustn't add
the inode number to free_ino_pinned (caching_thread() does it right).
In this case we need to try directly to add the number to the inode_cache
which will fail in this case.

When this inode number is allocated while it is still in free_ino_pinned,
it is allocated and still added to the free inode cache when the
pinned inodes are processed, thus one of the following inode number
allocations will get an inode that is already in use and fail with EEXIST
in btrfs_insert_empty_items().

One example which was created with the reproducer below:
Create a snapshot, work in the newly created snapshot for the rest.
In unlink(inode 34284) call btrfs_return_ino() which calls start_caching().
start_caching() calls add_free_space [34284, 18446744073709517077].
In btrfs_return_ino(), call start_caching pinned [34284, 1] which is wrong.
mkdir() call btrfs_find_ino_for_alloc() which returns the number 34284.
btrfs_unpin_free_ino calls add_free_space [34284, 1].
mkdir() call btrfs_find_ino_for_alloc() which returns the number 34284.
EEXIST when the new inode is inserted.

One possible reproducer is this one:
 # preparation
umount ${TEST_MNT} 2>/dev/null || true
mkfs.btrfs -f ${TEST_DEV}
mount ${TEST_DEV} ${TEST_MNT} -o \
btrfs subv create ${TEST_MNT}/s1
for i in `seq 34027`; do touch ${TEST_MNT}/s1/${i}; done
btrfs subv snap ${TEST_MNT}/s1 ${TEST_MNT}/s2
FILENAME=`find ${TEST_MNT}/s1/ -inum 4085 | sed 's|^.*/\([^/]*\)$|\1|'`
touch ${TEST_MNT}/s2/$FILENAME
 # the following steps can be repeated to reproduce the issue again and again
[ -e ${TEST_MNT}/s3 ] && btrfs subv del ${TEST_MNT}/s3
btrfs subv snap ${TEST_MNT}/s2 ${TEST_MNT}/s3
touch ${TEST_MNT}/s3/$FILENAME
ls -alFi ${TEST_MNT}/s?/$FILENAME
touch ${TEST_MNT}/s3/_1 || logger FAILED
ls -alFi ${TEST_MNT}/s?/_1
touch ${TEST_MNT}/s3/_2 || logger FAILED
ls -alFi ${TEST_MNT}/s?/_2
touch ${TEST_MNT}/s3/__1 || logger FAILED
ls -alFi ${TEST_MNT}/s?/__1
touch ${TEST_MNT}/s3/__2 || logger FAILED
ls -alFi ${TEST_MNT}/s?/__2
 # if the above is not enough, add the following loop:
for i in `seq 3 9`; do touch ${TEST_MNT}/s3/__${i} || logger FAILED; done
 #for i in `seq 3 34027`; do touch ${TEST_MNT}/s3/__${i} || logger FAILED; done
 # one of the touch(1) calls in s3 fail due to EEXIST because the inode is
 # already in use that btrfs_find_ino_for_alloc() returns.

Signed-off-by: Stefan Behrens <>
Reviewed-by: Jan Schmidt <>
Signed-off-by: Josef Bacik <>
Signed-off-by: Chris Mason <>
Signed-off-by: Ben Hutchings <>
9 years agoUSB: serial: fix sysfs-attribute removal deadlock
Johan Hovold [Wed, 23 Apr 2014 09:32:19 +0000 (11:32 +0200)]
USB: serial: fix sysfs-attribute removal deadlock

commit 10164c2ad6d2c16809f6c09e278f946e47801b3a upstream.

Fix driver new_id sysfs-attribute removal deadlock by making sure to
not hold any locks that the attribute operations grab when removing the

Specifically, usb_serial_deregister holds the table mutex when
deregistering the driver, which includes removing the new_id attribute.
This can lead to a deadlock as writing to new_id increments the
attribute's active count before trying to grab the same mutex in

The deadlock can easily be triggered by inserting a sleep in
usb_serial_deregister and writing the id of an unbound device to new_id
during module unload.

As the table mutex (in this case) is used to prevent subdriver unload
during probe, it should be sufficient to only hold the lock while
manipulating the usb-serial driver list during deregister. A racing
probe will then either fail to find a matching subdriver or fail to get
the corresponding module reference.

Since v3.15-rc1 this also triggers the following lockdep warning:

[ INFO: possible circular locking dependency detected ]
3.15.0-rc2 #123 Tainted: G        W
modprobe/190 is trying to acquire lock:
 (s_active#4){++++.+}, at: [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94

but task is already holding lock:
 (table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (table_lock){+.+.+.}:
       [<c0075f84>] __lock_acquire+0x1694/0x1ce4
       [<c0076de8>] lock_acquire+0xb4/0x154
       [<c03af3cc>] _raw_spin_lock+0x4c/0x5c
       [<c02bbc24>] usb_store_new_id+0x14c/0x1ac
       [<bf007eb4>] new_id_store+0x68/0x70 [usbserial]
       [<c025f568>] drv_attr_store+0x30/0x3c
       [<c01690e0>] sysfs_kf_write+0x5c/0x60
       [<c01682c0>] kernfs_fop_write+0xd4/0x194
       [<c010881c>] vfs_write+0xbc/0x198
       [<c0108e4c>] SyS_write+0x4c/0xa0
       [<c000f880>] ret_fast_syscall+0x0/0x48

-> #0 (s_active#4){++++.+}:
       [<c03a7a28>] print_circular_bug+0x68/0x2f8
       [<c0076218>] __lock_acquire+0x1928/0x1ce4
       [<c0076de8>] lock_acquire+0xb4/0x154
       [<c0166b70>] __kernfs_remove+0x254/0x310
       [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
       [<c0169fb8>] remove_files.isra.1+0x48/0x84
       [<c016a2fc>] sysfs_remove_group+0x58/0xac
       [<c016a414>] sysfs_remove_groups+0x34/0x44
       [<c02623b8>] driver_remove_groups+0x1c/0x20
       [<c0260e9c>] bus_remove_driver+0x3c/0xe4
       [<c026235c>] driver_unregister+0x38/0x58
       [<bf007fb4>] usb_serial_bus_deregister+0x84/0x88 [usbserial]
       [<bf004db4>] usb_serial_deregister+0x6c/0x78 [usbserial]
       [<bf005330>] usb_serial_deregister_drivers+0x2c/0x4c [usbserial]
       [<bf016618>] usb_serial_module_exit+0x14/0x1c [sierra]
       [<c009d6cc>] SyS_delete_module+0x184/0x210
       [<c000f880>] ret_fast_syscall+0x0/0x48

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----

 *** DEADLOCK ***

1 lock held by modprobe/190:
 #0:  (table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]

stack backtrace:
CPU: 0 PID: 190 Comm: modprobe Tainted: G        W     3.15.0-rc2 #123
[<c0015e10>] (unwind_backtrace) from [<c0013728>] (show_stack+0x20/0x24)
[<c0013728>] (show_stack) from [<c03a9a54>] (dump_stack+0x24/0x28)
[<c03a9a54>] (dump_stack) from [<c03a7cac>] (print_circular_bug+0x2ec/0x2f8)
[<c03a7cac>] (print_circular_bug) from [<c0076218>] (__lock_acquire+0x1928/0x1ce4)
[<c0076218>] (__lock_acquire) from [<c0076de8>] (lock_acquire+0xb4/0x154)
[<c0076de8>] (lock_acquire) from [<c0166b70>] (__kernfs_remove+0x254/0x310)
[<c0166b70>] (__kernfs_remove) from [<c0167aa0>] (kernfs_remove_by_name_ns+0x4c/0x94)
[<c0167aa0>] (kernfs_remove_by_name_ns) from [<c0169fb8>] (remove_files.isra.1+0x48/0x84)
[<c0169fb8>] (remove_files.isra.1) from [<c016a2fc>] (sysfs_remove_group+0x58/0xac)
[<c016a2fc>] (sysfs_remove_group) from [<c016a414>] (sysfs_remove_groups+0x34/0x44)
[<c016a414>] (sysfs_remove_groups) from [<c02623b8>] (driver_remove_groups+0x1c/0x20)
[<c02623b8>] (driver_remove_groups) from [<c0260e9c>] (bus_remove_driver+0x3c/0xe4)
[<c0260e9c>] (bus_remove_driver) from [<c026235c>] (driver_unregister+0x38/0x58)
[<c026235c>] (driver_unregister) from [<bf007fb4>] (usb_serial_bus_deregister+0x84/0x88 [usbserial])
[<bf007fb4>] (usb_serial_bus_deregister [usbserial]) from [<bf004db4>] (usb_serial_deregister+0x6c/0x78 [usbserial])
[<bf004db4>] (usb_serial_deregister [usbserial]) from [<bf005330>] (usb_serial_deregister_drivers+0x2c/0x4c [usbserial])
[<bf005330>] (usb_serial_deregister_drivers [usbserial]) from [<bf016618>] (usb_serial_module_exit+0x14/0x1c [sierra])
[<bf016618>] (usb_serial_module_exit [sierra]) from [<c009d6cc>] (SyS_delete_module+0x184/0x210)
[<c009d6cc>] (SyS_delete_module) from [<c000f880>] (ret_fast_syscall+0x0/0x48)

Signed-off-by: Johan Hovold <>
Signed-off-by: Greg Kroah-Hartman <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoARM: 8027/1: fix do_div() bug in big-endian systems
Xiangyu Lu [Tue, 15 Apr 2014 08:38:17 +0000 (09:38 +0100)]
ARM: 8027/1: fix do_div() bug in big-endian systems

commit 80bb3ef109ff40a7593d9481c17de9bbc4d7c0e2 upstream.

In big-endian systems, "%1" get the most significant part of the value, cause the instruction to get the wrong result.

When viewing ftrace record in big-endian ARM systems, we found that
the timestamp errors:

swapper-0   [001] 1325.970000:   0:120:R ==> [001]    16:120:R events/1
events/1-16 [001] 1325.970000:   16:120:S ==> [001]    0:120:R swapper
swapper-0   [000] 1325.1000000:  0:120:R   + [000]    15:120:R events/0
swapper-0   [000] 1325.1000000:  0:120:R ==> [000]    15:120:R events/0
swapper-0   [000] 1326.030000:   0:120:R   + [000]  1150:120:R sshd
swapper-0   [000] 1326.030000:   0:120:R ==> [000]  1150:120:R sshd

When viewed ftrace records, it will call the do_div(n, base) function, which achieved arch/arm/include/asm/div64.h in. When n = 10000000, base = 1000000, in do_div(n, base) will execute "umull %Q0, %R0, %1, %Q2".

Reviewed-by: Dave Martin <>
Reviewed-by: Nicolas Pitre <>
Signed-off-by: Alex Wu <>
Signed-off-by: Xiangyu Lu <>
Signed-off-by: Russell King <>
Signed-off-by: Ben Hutchings <>
9 years agomm: make fixup_user_fault() check the vma access rights too
Linus Torvalds [Tue, 22 Apr 2014 20:49:40 +0000 (13:49 -0700)]
mm: make fixup_user_fault() check the vma access rights too

commit 1b17844b29ae042576bea588164f2f1e9590a8bc upstream.

fixup_user_fault() is used by the futex code when the direct user access
fails, and the futex code wants it to either map in the page in a usable
form or return an error.  It relied on handle_mm_fault() to map the
page, and correctly checked the error return from that, but while that
does map the page, it doesn't actually guarantee that the page will be
mapped with sufficient permissions to be then accessed.

So do the appropriate tests of the vma access rights by hand.

[ Side note: arguably handle_mm_fault() could just do that itself, but
  we have traditionally done it in the caller, because some callers -
  notably get_user_pages() - have been able to access pages even when
  they are mapped with PROT_NONE.  Maybe we should re-visit that design
  decision, but in the meantime this is the minimal patch. ]

Found by Dave Jones running his trinity tool.

Reported-by: Dave Jones <>
Acked-by: Hugh Dickins <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
9 years agoInput: synaptics - add min/max quirk for ThinkPad T431s, L440, L540, S1 Yoga and X1
Hans de Goede [Sun, 20 Apr 2014 05:31:18 +0000 (22:31 -0700)]
Input: synaptics - add min/max quirk for ThinkPad T431s, L440, L540, S1 Yoga and X1

commit 46a2986ebbe18757c2d8c352f8fb6e0f4f0754e3 upstream.

We expect that all the Haswell series will need such quirks, sigh.

The T431s seems to be T430 hardware in a T440s case, using the T440s touchpad,
with the same min/max issue.

The X1 Carbon 3rd generation name says 2nd while it is a 3rd generation.

The X1 and T431s share a PnPID with the T540p, but the reported ranges are
closer to those of the T440s.

HdG: Squashed 5 quirk patches into one. T431s + L440 + L540 are written by me,
S1 Yoga and X1 are written by Benjamin Tissoires.

Hdg: Standardized S1 Yoga and X1 values, Yoga uses the same touchpad as the
X240, X1 uses the same touchpad as the T440.

Signed-off-by: Benjamin Tissoires <>
Signed-off-by: Hans de Goede <>
Signed-off-by: Dmitry Torokhov <>
Signed-off-by: Ben Hutchings <>
9 years agodmi: add support for exact DMI matches in addition to substring matching
Jani Nikula [Wed, 3 Jul 2013 22:05:02 +0000 (15:05 -0700)]
dmi: add support for exact DMI matches in addition to substring matching

commit 5017b2851373ee15c7035151853bb1448800cae2 upstream.

dmi_match() considers a substring match to be a successful match.  This is
not always sufficient to distinguish between DMI data for different
systems.  Add support for exact string matching using strcmp() in addition
to the substring matching using strstr().

The specific use case in the i915 driver is to allow us to use an exact
match for D510MO, without also incorrectly matching D510MOV:

.ident = "Intel D510MO",
.matches = {

Signed-off-by: Jani Nikula <>
Cc: <>
Cc: Chris Wilson <>
Cc: Cornel Panceac <>
Acked-by: Daniel Vetter <>
Cc: Greg KH <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
9 years agomm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
Mizuma, Masayoshi [Fri, 18 Apr 2014 22:07:18 +0000 (15:07 -0700)]
mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()

commit 7848a4bf51b34f41fcc9bd77e837126d99ae84e3 upstream.

soft lockup in freeing gigantic hugepage fixed in commit 55f67141a892 "mm:
hugetlb: fix softlockup when a large number of hugepages are freed." can
happen in return_unused_surplus_pages(), so let's fix it.

Signed-off-by: Masayoshi Mizuma <>
Signed-off-by: Naoya Horiguchi <>
Cc: Joonsoo Kim <>
Cc: Michal Hocko <>
Cc: Aneesh Kumar <>
Cc: KOSAKI Motohiro <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agolibata/ahci: accommodate tag ordered controllers
Dan Williams [Thu, 17 Apr 2014 18:48:21 +0000 (11:48 -0700)]
libata/ahci: accommodate tag ordered controllers

commit 8a4aeec8d2d6a3edeffbdfae451cdf05cbf0fefd upstream.

The AHCI spec allows implementations to issue commands in tag order
rather than FIFO order: P:SelectCmd
HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1)
or HBA selects the command to issue that has had the
PxCI bit set to '1' longer than any other command
pending to be issued.

The result is that commands posted sequentially (time-wise) may play out
of sequence when issued by hardware.

This behavior has likely been hidden by drives that arrange for commands
to complete in issue order.  However, it appears recent drives (two from
different vendors that we have found so far) inflict out-of-order
completions as a matter of course.  So, we need to take care to maintain
ordered submission, otherwise we risk triggering a drive to fall out of
sequential-io automation and back to random-io processing, which incurs
large latency and degrades throughput.

This issue was found in simple benchmarks where QD=2 seq-write
performance was 30-50% *greater* than QD=32 seq-write performance.

Tagging for -stable and making the change globally since it has a low
risk-to-reward ratio.  Also, word is that recent versions of an unnamed
OS also does it this way now.  So, drives in the field are already
experienced with this tag ordering scheme.

Cc: Dave Jiang <>
Cc: Ed Ciechanowski <>
Reviewed-by: Matthew Wilcox <>
Signed-off-by: Dan Williams <>
Signed-off-by: Tejun Heo <>
Signed-off-by: Ben Hutchings <>
9 years agonfsd: set timeparms.to_maxval in setup_callback_client
Jeff Layton [Tue, 15 Apr 2014 12:51:48 +0000 (08:51 -0400)]
nfsd: set timeparms.to_maxval in setup_callback_client

commit 3758cf7e14b753838fe754ede3862af10b35fdac upstream.

...otherwise the logic in the timeout handling doesn't work correctly.

Spotted-by: Trond Myklebust <>
Signed-off-by: Jeff Layton <>
Signed-off-by: J. Bruce Fields <>
[bwh: Backported to 3.2: max_cb_time() takes no parameters]
Signed-off-by: Ben Hutchings <>
9 years agoUSB: cdc-acm: Remove Motorola/Telit H24 serial interfaces from ACM driver
Michael Ulbricht [Tue, 25 Mar 2014 09:34:18 +0000 (10:34 +0100)]
USB: cdc-acm: Remove Motorola/Telit H24 serial interfaces from ACM driver

commit 895d240d1db0b2736d779200788e4c4aea28a0c6 upstream.

By specifying NO_UNION_NORMAL the ACM driver does only use the first two
USB interfaces (modem data & control). The AT Port, Diagnostic and NMEA
interfaces are left to the USB serial driver.

Signed-off-by: Michael Ulbricht <>
Signed-off-by: Alexander Stein <>
Signed-off-by: Oliver Neukum <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
9 years agoUSB: pl2303: add ids for Hewlett-Packard HP POS pole displays
Aaron Sanders [Mon, 31 Mar 2014 13:54:21 +0000 (15:54 +0200)]
USB: pl2303: add ids for Hewlett-Packard HP POS pole displays

commit b16c02fbfb963fa2941b7517ebf1f8a21946775e upstream.

Add device ids to pl2303 for the Hewlett-Packard HP POS pole displays:

LD960: 03f0:0B39
LCM220: 03f0:3139
LCM960: 03f0:3239

[ Johan: fix indentation and sort PIDs numerically ]

Signed-off-by: Aaron Sanders <>
Signed-off-by: Johan Hovold <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
9 years agoUSB: cp210x: Add 8281 (Nanotec Plug & Drive)
Tristan Bruns [Sun, 13 Apr 2014 21:57:16 +0000 (23:57 +0200)]
USB: cp210x: Add 8281 (Nanotec Plug & Drive)

commit 72b3007951010ce1bbf950e23b19d9839fa905a5 upstream.

Signed-off-by: Tristan Bruns <>
Signed-off-by: Johan Hovold <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
9 years agousb: option driver, add support for Telit UE910v2
Daniele Palmas [Wed, 2 Apr 2014 09:19:48 +0000 (11:19 +0200)]
usb: option driver, add support for Telit UE910v2

commit d6de486bc22255779bd54b0fceb4c240962bf146 upstream.

option driver, added VID/PID for Telit UE910v2 modem

Signed-off-by: Daniele Palmas <>
Signed-off-by: Johan Hovold <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
9 years agoRevert "USB: serial: add usbid for dell wwan card to sierra.c"
Johan Hovold [Fri, 28 Mar 2014 17:05:10 +0000 (18:05 +0100)]
Revert "USB: serial: add usbid for dell wwan card to sierra.c"

commit 2e01280d2801c72878cf3a7119eac30077b463d5 upstream.

This reverts commit 1ebca9dad5abe8b2ed4dbd186cd657fb47c1f321.

This device was erroneously added to the sierra driver even though it's
not a Sierra device and was already handled by the option driver.

Cc: Richard Farina <>
Signed-off-by: Johan Hovold <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
9 years agoUSB: serial: ftdi_sio: add id for Brainboxes serial cards
Michele Baldessari [Mon, 31 Mar 2014 08:51:00 +0000 (10:51 +0200)]
USB: serial: ftdi_sio: add id for Brainboxes serial cards

commit efe26e16b1d93ac0085e69178cc18811629e8fc5 upstream.

Custom VID/PIDs for Brainboxes cards as reported in

Signed-off-by: Michele Baldessari <>
Signed-off-by: Johan Hovold <>
Signed-off-by: Greg Kroah-Hartman <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agostaging: r8712u: Fix case where ethtype was never obtained and always be checked...
Larry Finger [Wed, 16 Apr 2014 19:49:33 +0000 (14:49 -0500)]
staging: r8712u: Fix case where ethtype was never obtained and always be checked against 0

commit f764cd68d9036498f08fe8834deb6a367b5c2542 upstream.

Zero-initializing ether_type masked that the ether type would never be
obtained for 8021x packets and the comparison against eapol_type
would always fail.

Reported-by: Jes Sorensen <>
Signed-off-by: Larry Finger <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
9 years agomlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
Chris Mason [Tue, 15 Apr 2014 22:09:24 +0000 (18:09 -0400)]
mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll

commit c98235cb8584a72e95786e17d695a8e5fafcd766 upstream.

The mlx4 driver is triggering schedules while atomic inside

spin_lock_irqsave(&cq->lock, flags);
^^^^^ msleep here
mlx4_en_process_rx_cq(dev, cq, 0);
spin_unlock_irqrestore(&cq->lock, flags);

This was part of a patch by Alexander Guller from Mellanox in 2011,
but it still isn't upstream.

Signed-off-by: Chris Mason <>
Acked-By: Amir Vadai <>
Signed-off-by: David S. Miller <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agolocks: allow __break_lease to sleep even when break_time is 0
Jeff Layton [Tue, 15 Apr 2014 10:17:49 +0000 (06:17 -0400)]
locks: allow __break_lease to sleep even when break_time is 0

commit f1c6bb2cb8b81013e8979806f8e15e3d53efb96d upstream.

A fl->fl_break_time of 0 has a special meaning to the lease break code
that basically means "never break the lease". knfsd uses this to ensure
that leases don't disappear out from under it.

Unfortunately, the code in __break_lease can end up passing this value
to wait_event_interruptible as a timeout, which prevents it from going
to sleep at all. This makes __break_lease to spin in a tight loop and
causes soft lockups.

Fix this by ensuring that we pass a minimum value of 1 as a timeout

Cc: J. Bruce Fields <>
Reported-by: Terry Barnaby <>
Signed-off-by: Jeff Layton <>
Signed-off-by: Ben Hutchings <>
9 years agoparisc: fix epoll_pwait syscall on compat kernel
Helge Deller [Sat, 12 Apr 2014 22:03:55 +0000 (00:03 +0200)]
parisc: fix epoll_pwait syscall on compat kernel

commit ab3e55b119c9653b19ea4edffb86f04db867ac98 upstream.

This bug was detected with the libio-epoll-perl debian package where the
test case IO-Ppoll-compat.t failed.

Signed-off-by: Helge Deller <>
Signed-off-by: Ben Hutchings <>
9 years agoext4: use i_size_read in ext4_unaligned_aio()
Theodore Ts'o [Sat, 12 Apr 2014 16:45:25 +0000 (12:45 -0400)]
ext4: use i_size_read in ext4_unaligned_aio()

commit 6e6358fc3c3c862bfe9a5bc029d3f8ce43dc9765 upstream.

We haven't taken i_mutex yet, so we need to use i_size_read().

Signed-off-by: "Theodore Ts'o" <>
Signed-off-by: Ben Hutchings <>
9 years agoext4: note the error in ext4_end_bio()
Matthew Wilcox [Mon, 7 Apr 2014 14:54:20 +0000 (10:54 -0400)]
ext4: note the error in ext4_end_bio()

commit 9503c67c93ed0b95ba62d12d1fd09da6245dbdd6 upstream.

ext4_end_bio() currently throws away the error that it receives.  Chances
are this is part of a spate of errors, one of which will end up getting
the error returned to userspace somehow, but we shouldn't take that risk.
Also print out the errno to aid in debug.

Signed-off-by: Matthew Wilcox <>
Signed-off-by: "Theodore Ts'o" <>
Reviewed-by: Jan Kara <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoext4: FIBMAP ioctl causes BUG_ON due to handle EXT_MAX_BLOCKS
Kazuya Mio [Mon, 7 Apr 2014 14:53:28 +0000 (10:53 -0400)]
ext4: FIBMAP ioctl causes BUG_ON due to handle EXT_MAX_BLOCKS

commit 4adb6ab3e0fa71363a5ef229544b2d17de6600d7 upstream.

When we try to get 2^32-1 block of the file which has the extent
(ee_block=2^32-2, ee_len=1) with FIBMAP ioctl, it causes BUG_ON
in ext4_ext_put_gap_in_cache().

To avoid the problem, ext4_map_blocks() needs to check the file logical block
number. ext4_ext_put_gap_in_cache() called via ext4_map_blocks() cannot
handle 2^32-1 because the maximum file logical block number is 2^32-2.

Note that ext4_ind_map_blocks() returns -EIO when the block number is invalid.
So ext4_map_blocks() should also return the same errno.

Signed-off-by: Kazuya Mio <>
Signed-off-by: "Theodore Ts'o" <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoLinux 3.2.58 v3.2.58
Ben Hutchings [Wed, 30 Apr 2014 15:23:28 +0000 (16:23 +0100)]
Linux 3.2.58

9 years agoRevert "isci: fix reset timeout handling"
Ben Hutchings [Wed, 30 Apr 2014 12:22:22 +0000 (13:22 +0100)]
Revert "isci: fix reset timeout handling"

This reverts commit 584ec12265192bf49dfa270d517380f6723a6956, which
was commit ddfadd7736b677de2d4ca2cd5b4b655368c85a7a upstream.  It
causes boot failure on 3.2 although no such problem occurs upstream.

Reported-by: Ondrej Zary <>
Signed-off-by: Ben Hutchings <>
Acked-by: Dan Williams <>
9 years agoRevert "alpha: fix broken network checksum"
Ben Hutchings [Mon, 28 Apr 2014 01:04:30 +0000 (02:04 +0100)]
Revert "alpha: fix broken network checksum"

This reverts commit b93b90ff7c50288d602108ae1a09673df3f799a8, which
was commit 0ef38d70d4118b2ce1a538d14357be5ff9dc2bbd upstream.
It was intended to fix a regression which never occurred in 3.2.

9 years agopowernow-k6: reorder frequencies
Mikulas Patocka [Thu, 12 Dec 2013 00:39:19 +0000 (19:39 -0500)]
powernow-k6: reorder frequencies

commit 22c73795b101597051924556dce019385a1e2fa0 upstream.

This patch reorders reported frequencies from the highest to the lowest,
just like in other frequency drivers.

Signed-off-by: Mikulas Patocka <>
Acked-by: Viresh Kumar <>
Signed-off-by: Rafael J. Wysocki <>
[bwh: Backported to 3.2: cpu_frequency_table::driver_data is called index]
Signed-off-by: Ben Hutchings <>
9 years agopowernow-k6: correctly initialize default parameters
Mikulas Patocka [Thu, 12 Dec 2013 00:38:53 +0000 (19:38 -0500)]
powernow-k6: correctly initialize default parameters

commit d82b922a4acc1781d368aceac2f9da43b038cab2 upstream.

The powernow-k6 driver used to read the initial multiplier from the
powernow register. However, there is a problem with this:

* If there was a frequency transition before, the multiplier read from the
  register corresponds to the current multiplier.
* If there was no frequency transition since reset, the field in the
  register always reads as zero, regardless of the current multiplier that
  is set using switches on the mainboard and that the CPU is running at.

The zero value corresponds to multiplier 4.5, so as a consequence, the
powernow-k6 driver always assumes multiplier 4.5.

For example, if we have 550MHz CPU with bus frequency 100MHz and
multiplier 5.5, the powernow-k6 driver thinks that the multiplier is 4.5
and bus frequency is 122MHz. The powernow-k6 driver then sets the
multiplier to 4.5, underclocking the CPU to 450MHz, but reports the
current frequency as 550MHz.

There is no reliable way how to read the initial multiplier. I modified
the driver so that it contains a table of known frequencies (based on
parameters of existing CPUs and some common overclocking schemes) and sets
the multiplier according to the frequency. If the frequency is unknown
(because of unusual overclocking or underclocking), the user must supply
the bus speed and maximum multiplier as module parameters.

This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.

Signed-off-by: Mikulas Patocka <>
Signed-off-by: Rafael J. Wysocki <>
[bwh: Backported to 3.2:
 - Adjust context
 - s/driver_data/index/]
Signed-off-by: Ben Hutchings <>
9 years agopowernow-k6: disable cache when changing frequency
Mikulas Patocka [Thu, 12 Dec 2013 00:38:32 +0000 (19:38 -0500)]
powernow-k6: disable cache when changing frequency

commit e20e1d0ac02308e2211306fc67abcd0b2668fb8b upstream.

I found out that a system with k6-3+ processor is unstable during network
server load. The system locks up or the network card stops receiving. The
reason for the instability is the CPU frequency scaling.

During frequency transition the processor is in "EPM Stop Grant" state.
The documentation says that the processor doesn't respond to inquiry
requests in this state. Consequently, coherency of processor caches and
bus master devices is not maintained, causing the system instability.

This patch flushes the cache during frequency transition. It fixes the

Other minor changes:
* u64 invalue changed to unsigned long because the variable is 32-bit
* move the logic to set the multiplier to a separate function
* preserve lower 5 bits of the powernow port instead of 4 (the voltage
  field has 5 bits)
* mask interrupts when reading the multiplier, so that the port is not
  open during other activity (running other kernel code with the port open
  shouldn't cause any misbehavior, but we should better be safe and keep
  the port closed)

This patch should be backported to all stable kernels. If it doesn't
apply cleanly, change it, or ask me to change it.

Signed-off-by: Mikulas Patocka <>
Signed-off-by: Rafael J. Wysocki <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoselinux: correctly label /proc inodes in use before the policy is loaded
Paul Moore [Wed, 19 Mar 2014 20:46:18 +0000 (16:46 -0400)]
selinux: correctly label /proc inodes in use before the policy is loaded

commit f64410ec665479d7b4b77b7519e814253ed0f686 upstream.

This patch is based on an earlier patch by Eric Paris, he describes
the problem below:

  "If an inode is accessed before policy load it will get placed on a
   list of inodes to be initialized after policy load.  After policy
   load we call inode_doinit() which calls inode_doinit_with_dentry()
   on all inodes accessed before policy load.  In the case of inodes
   in procfs that means we'll end up at the bottom where it does:

     /* Default to the fs superblock SID. */
     isec->sid = sbsec->sid;

     if ((sbsec->flags & SE_SBPROC) && !S_ISLNK(inode->i_mode)) {
             if (opt_dentry) {
                     isec->sclass = inode_mode_to_security_class(...)
                     rc = selinux_proc_get_sid(opt_dentry,
                     if (rc)
                             goto out_unlock;
                     isec->sid = sid;

   Since opt_dentry is null, we'll never call selinux_proc_get_sid()
   and will leave the inode labeled with the label on the superblock.
   I believe a fix would be to mimic the behavior of xattrs.  Look
   for an alias of the inode.  If it can't be found, just leave the
   inode uninitialized (and pick it up later) if it can be found, we
   should be able to call selinux_proc_get_sid() ..."

On a system exhibiting this problem, you will notice a lot of files in
/proc with the generic "proc_t" type (at least the ones that were
accessed early in the boot), for example:

   # ls -Z /proc/sys/kernel/shmmax | awk '{ print $4 " " $5 }'
   system_u:object_r:proc_t:s0 /proc/sys/kernel/shmmax

However, with this patch in place we see the expected result:

   # ls -Z /proc/sys/kernel/shmmax | awk '{ print $4 " " $5 }'
   system_u:object_r:sysctl_kernel_t:s0 /proc/sys/kernel/shmmax

Cc: Eric Paris <>
Signed-off-by: Paul Moore <>
Acked-by: Eric Paris <>
Signed-off-by: Ben Hutchings <>
9 years agoChar: ipmi_bt_sm, fix infinite loop
Jiri Slaby [Mon, 14 Apr 2014 14:46:50 +0000 (09:46 -0500)]
Char: ipmi_bt_sm, fix infinite loop

commit a94cdd1f4d30f12904ab528152731fb13a812a16 upstream.

In read_all_bytes, we do

  unsigned char i;
  bt->read_data[0] = BMC2HOST;
  bt->read_count = bt->read_data[0];
  for (i = 1; i <= bt->read_count; i++)
    bt->read_data[i] = BMC2HOST;

If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the
'for' loop.  Make 'i' an 'int' instead of 'char' to get rid of the
overflow and finish the loop after 255 iterations every time.

Signed-off-by: Jiri Slaby <>
Reported-and-debugged-by: Rui Hui Dian <>
Cc: Tomas Cech <>
Cc: Corey Minyard <>
Cc: <>
Signed-off-by: Corey Minyard <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
9 years agodrivers: hv: additional switch to use mb() instead of smp_mb()
Qiang Huang [Fri, 18 Apr 2014 09:29:24 +0000 (17:29 +0800)]
drivers: hv: additional switch to use mb() instead of smp_mb()

commit e4af376d04b0(drivers: hv: switch to use mb() instead of smp_mb()),
the adjustment mistakenly dropped the change in hv_ringbuffer_read,
so add it.

Signed-off-by: Qiang Huang <>
Signed-off-by: Ben Hutchings <>
9 years agotarget/tcm_fc: Fix use-after-free of ft_tpg
Andy Grover [Fri, 4 Apr 2014 23:44:37 +0000 (16:44 -0700)]
target/tcm_fc: Fix use-after-free of ft_tpg

commit 2c42be2dd4f6586728dba5c4e197afd5cfaded78 upstream.

ft_del_tpg checks tpg->tport is set before unlinking the tpg from the
tport when the tpg is being removed. Set this pointer in ft_tport_create,
or the unlinking won't happen in ft_del_tpg and tport->tpg will reference
a deleted object.

This patch sets tpg->tport in ft_tport_create, because that's what
ft_del_tpg checks, and is the only way to get back to the tport to
clear tport->tpg.

The bug was occuring when:

- lport created, tport (our per-lport, per-provider context) is
  tport->tpg = NULL
- tpg created
- a PRLI is received. ft_tport_create is called, tpg is found and
  tport->tpg is set
- tpg removed. ft_tpg is freed in ft_del_tpg. Since tpg->tport was not
  set, tport->tpg is not cleared and points at freed memory
- Future calls to ft_tport_create return tport via first conditional,
  instead of searching for new tpg by calling ft_lport_find_tpg.
  tport->tpg is still invalid, and will access freed memory.


Signed-off-by: Andy Grover <>
Signed-off-by: Nicholas Bellinger <>
Signed-off-by: Ben Hutchings <>
9 years agox86-64, modify_ldt: Ban 16-bit segments on 64-bit kernels
H. Peter Anvin [Sun, 16 Mar 2014 22:31:54 +0000 (15:31 -0700)]
x86-64, modify_ldt: Ban 16-bit segments on 64-bit kernels

commit b3b42ac2cbae1f3cecbb6229964a4d48af31d382 upstream.

The IRET instruction, when returning to a 16-bit segment, only
restores the bottom 16 bits of the user space stack pointer.  We have
a software workaround for that ("espfix") for the 32-bit kernel, but
it relies on a nonzero stack segment base which is not available in
32-bit mode.

Since 16-bit support is somewhat crippled anyway on a 64-bit kernel
(no V86 mode), and most (if not quite all) 64-bit processors support
virtualization for the users who really need it, simply reject
attempts at creating a 16-bit segment when running on top of a 64-bit

Cc: Linus Torvalds <>
Signed-off-by: H. Peter Anvin <>
Signed-off-by: Ben Hutchings <>
9 years agob43: Fix machine check error due to improper access of B43_MMIO_PSM_PHY_HDR
Rafał Miłecki [Sat, 5 Apr 2014 16:08:25 +0000 (18:08 +0200)]
b43: Fix machine check error due to improper access of B43_MMIO_PSM_PHY_HDR

commit 12cd43c6ed6da7bf7c5afbd74da6959cda6d056b upstream.

Register B43_MMIO_PSM_PHY_HDR is 16 bit one, so accessing it with 32b
functions isn't safe. On my machine it causes delayed (!) CPU exception:

Disabling lock debugging due to kernel taint
mce: [Hardware Error]: CPU 0: Machine Check Exception: 4 Bank 4: b200000000070f0f
mce: [Hardware Error]: TSC 164083803dc
mce: [Hardware Error]: PROCESSOR 2:20fc2 TIME 1396650505 SOCKET 0 APIC 0 microcode 0
mce: [Hardware Error]: Run the above through 'mcelog --ascii'
mce: [Hardware Error]: Machine check: Processor context corrupt
Kernel panic - not syncing: Fatal machine check on current CPU
Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff)

Signed-off-by: Rafał Miłecki <>
Acked-by: Larry Finger <>
Signed-off-by: John W. Linville <>
Signed-off-by: Ben Hutchings <>
9 years agolib/percpu_counter.c: fix bad percpu counter state during suspend
Jens Axboe [Tue, 8 Apr 2014 23:04:12 +0000 (16:04 -0700)]
lib/percpu_counter.c: fix bad percpu counter state during suspend

commit e39435ce68bb4685288f78b1a7e24311f7ef939f upstream.

I got a bug report yesterday from Laszlo Ersek in which he states that
his kvm instance fails to suspend.  Laszlo bisected it down to this
commit 1cf7e9c68fe8 ("virtio_blk: blk-mq support") where virtio-blk is
converted to use the blk-mq infrastructure.

After digging a bit, it became clear that the issue was with the queue
drain.  blk-mq tracks queue usage in a percpu counter, which is
incremented on request alloc and decremented when the request is freed.
The initial hunt was for an inconsistency in blk-mq, but everything
seemed fine.  In fact, the counter only returned crazy values when
suspend was in progress.

When a CPU is unplugged, the percpu counters merges that CPU state with
the general state.  blk-mq takes care to register a hotcpu notifier with
the appropriate priority, so we know it runs after the percpu counter
notifier.  However, the percpu counter notifier only merges the state
when the CPU is fully gone.  This leaves a state transition where the
CPU going away is no longer in the online mask, yet it still holds
private values.  This means that in this state, percpu_counter_sum()
returns invalid results, and the suspend then hangs waiting for
abs(dead-cpu-value) requests to complete which of course will never

Fix this by clearing the state earlier, so we never have a case where
the CPU isn't in online mask but still holds private state.  This bug
has been there since forever, I guess we don't have a lot of users where
percpu counters needs to be reliable during the suspend cycle.

Signed-off-by: Jens Axboe <>
Reported-by: Laszlo Ersek <>
Tested-by: Laszlo Ersek <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
9 years agoALSA: ice1712: Fix boundary checks in PCM pointer ops
Takashi Iwai [Tue, 8 Apr 2014 14:58:34 +0000 (16:58 +0200)]
ALSA: ice1712: Fix boundary checks in PCM pointer ops

commit 4f8e940095536bc002a81666a4107a581c84e9b9 upstream.

PCM pointer callbacks in ice1712 driver check the buffer size boundary
wrongly between bytes and frames.  This leads to PCM core warnings
   snd_pcm_update_hw_ptr0: 105 callbacks suppressed
   ALSA pcm_lib.c:352 BUG: pcmC3D0c:0, pos = 5461, buffer size = 5461, period size = 2730

This patch fixes these checks to be placed after the proper unit

Signed-off-by: Takashi Iwai <>
Signed-off-by: Ben Hutchings <>
9 years agowait: fix reparent_leader() vs EXIT_DEAD->EXIT_ZOMBIE race
Oleg Nesterov [Mon, 7 Apr 2014 22:38:41 +0000 (15:38 -0700)]
wait: fix reparent_leader() vs EXIT_DEAD->EXIT_ZOMBIE race

commit dfccbb5e49a621c1b21a62527d61fc4305617aca upstream.

wait_task_zombie() first does EXIT_ZOMBIE->EXIT_DEAD transition and
drops tasklist_lock.  If this task is not the natural child and it is
traced, we change its state back to EXIT_ZOMBIE for ->real_parent.

The last transition is racy, this is even documented in 50b8d257486a
"ptrace: partially fix the do_wait(WEXITED) vs EXIT_DEAD->EXIT_ZOMBIE
race".  wait_consider_task() tries to detect this transition and clear
->notask_error but we can't rely on ptrace_reparented(), debugger can
exit and do ptrace_unlink() before its sub-thread sets EXIT_ZOMBIE.

And there is another problem which were missed before: this transition
can also race with reparent_leader() which doesn't reset >exit_signal if
EXIT_DEAD, assuming that this task must be reaped by someone else.  So
the tracee can be re-parented with ->exit_signal != SIGCHLD, and if
/sbin/init doesn't use __WALL it becomes unreapable.

Change reparent_leader() to update ->exit_signal even if EXIT_DEAD.
Note: this is the simple temporary hack for -stable, it doesn't try to
solve all problems, it will be reverted by the next changes.

Signed-off-by: Oleg Nesterov <>
Reported-by: Jan Kratochvil <>
Reported-by: Michal Schmidt <>
Tested-by: Michal Schmidt <>
Cc: Al Viro <>
Cc: Lennart Poettering <>
Cc: Roland McGrath <>
Cc: Tejun Heo <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
9 years agomm: hugetlb: fix softlockup when a large number of hugepages are freed.
Mizuma, Masayoshi [Mon, 7 Apr 2014 22:37:54 +0000 (15:37 -0700)]
mm: hugetlb: fix softlockup when a large number of hugepages are freed.

commit 55f67141a8927b2be3e51840da37b8a2320143ed upstream.

When I decrease the value of nr_hugepage in procfs a lot, softlockup
happens.  It is because there is no chance of context switch during this

On the other hand, when I allocate a large number of hugepages, there is
some chance of context switch.  Hence softlockup doesn't happen during
this process.  So it's necessary to add the context switch in the
freeing process as same as allocating process to avoid softlockup.

When I freed 12 TB hugapages with kernel-2.6.32-358.el6, the freeing
process occupied a CPU over 150 seconds and following softlockup message
appeared twice or more.

$ echo 6000000 > /proc/sys/vm/nr_hugepages
$ cat /proc/sys/vm/nr_hugepages
$ grep ^Huge /proc/meminfo
HugePages_Total:   6000000
HugePages_Free:    6000000
HugePages_Rsvd:        0
HugePages_Surp:        0
Hugepagesize:       2048 kB
$ echo 0 > /proc/sys/vm/nr_hugepages

BUG: soft lockup - CPU#16 stuck for 67s! [sh:12883] ...
Pid: 12883, comm: sh Not tainted 2.6.32-358.el6.x86_64 #1
Call Trace:

I have not confirmed this problem with upstream kernels because I am not
able to prepare the machine equipped with 12TB memory now.  However I
confirmed that the amount of decreasing hugepages was directly
proportional to the amount of required time.

I measured required times on a smaller machine.  It showed 130-145
hugepages decreased in a millisecond.

  Amount of decreasing     Required time      Decreasing rate
  hugepages                     (msec)         (pages/msec)
  10,000 pages == 20GB         70 -  74          135-142
  30,000 pages == 60GB        208 - 229          131-144

It means decrement of 6TB hugepages will trigger softlockup with the
default threshold 20sec, in this decreasing rate.

Signed-off-by: Masayoshi Mizuma <>
Cc: Joonsoo Kim <>
Cc: Michal Hocko <>
Cc: Wanpeng Li <>
Cc: Aneesh Kumar <>
Cc: KOSAKI Motohiro <>
Cc: Naoya Horiguchi <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
9 years agomm: try_to_unmap_cluster() should lock_page() before mlocking
Vlastimil Babka [Mon, 7 Apr 2014 22:37:50 +0000 (15:37 -0700)]
mm: try_to_unmap_cluster() should lock_page() before mlocking

commit 57e68e9cd65b4b8eb4045a1e0d0746458502554c upstream.

A BUG_ON(!PageLocked) was triggered in mlock_vma_page() by Sasha Levin
fuzzing with trinity.  The call site try_to_unmap_cluster() does not lock
the pages other than its check_page parameter (which is already locked).

The BUG_ON in mlock_vma_page() is not documented and its purpose is
somewhat unclear, but apparently it serializes against page migration,
which could otherwise fail to transfer the PG_mlocked flag.  This would
not be fatal, as the page would be eventually encountered again, but
NR_MLOCK accounting would become distorted nevertheless.  This patch adds
a comment to the BUG_ON in mlock_vma_page() and munlock_vma_page() to that

The call site try_to_unmap_cluster() is fixed so that for page !=
check_page, trylock_page() is attempted (to avoid possible deadlocks as we
already have check_page locked) and mlock_vma_page() is performed only
upon success.  If the page lock cannot be obtained, the page is left
without PG_mlocked, which is again not a problem in the whole unevictable
memory design.

Signed-off-by: Vlastimil Babka <>
Signed-off-by: Bob Liu <>
Reported-by: Sasha Levin <>
Cc: Wanpeng Li <>
Cc: Michel Lespinasse <>
Cc: KOSAKI Motohiro <>
Acked-by: Rik van Riel <>
Cc: David Rientjes <>
Cc: Mel Gorman <>
Cc: Hugh Dickins <>
Cc: Joonsoo Kim <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoiscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug
Nicholas Bellinger [Wed, 19 Feb 2014 23:32:14 +0000 (23:32 +0000)]
iscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug

commit d444edc679e7713412f243b792b1f964e5cff1e1 upstream.

This patch fixes a long-standing bug in iscsit_build_conn_drop_async_message()
where during ERL=2 connection recovery, a bogus conn_p pointer could
end up being used to send the ISCSI_OP_ASYNC_EVENT + DROPPING_CONNECTION
notifying the initiator that cmd->logout_cid has failed.

The bug was manifesting itself as an OOPs in iscsit_allocate_cmd() with
a bogus conn_p pointer in iscsit_build_conn_drop_async_message().

Reported-by: Arshad Hussain <>
Reported-by: santosh kulkarni <>
Signed-off-by: Nicholas Bellinger <>
Signed-off-by: Ben Hutchings <>
9 years agoocfs2: do not put bh when buffer_uptodate failed
alex chen [Thu, 3 Apr 2014 21:47:05 +0000 (14:47 -0700)]
ocfs2: do not put bh when buffer_uptodate failed

commit f7cf4f5bfe073ad792ab49c04f247626b3e38db6 upstream.

Do not put bh when buffer_uptodate failed in ocfs2_write_block and
ocfs2_write_super_or_backup, because it will put bh in b_end_io.
Otherwise it will hit a warning "VFS: brelse: Trying to free free

Signed-off-by: Alex Chen <>
Reviewed-by: Joseph Qi <>
Reviewed-by: Srinivas Eeda <>
Cc: Mark Fasheh <>
Acked-by: Joel Becker <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
9 years agoocfs2: dlm: fix recovery hung
Junxiao Bi [Thu, 3 Apr 2014 21:46:51 +0000 (14:46 -0700)]
ocfs2: dlm: fix recovery hung

commit ded2cf71419b9353060e633b59e446c42a6a2a09 upstream.

There is a race window in dlm_do_recovery() between dlm_remaster_locks()
and dlm_reset_recovery() when the recovery master nearly finish the
recovery process for a dead node.  After the master sends FINALIZE_RECO
message in dlm_remaster_locks(), another node may become the recovery
master for another dead node, and then send the BEGIN_RECO message to
all the nodes included the old master, in the handler of this message
dlm_begin_reco_handler() of old master, dlm->reco.dead_node and
dlm->reco.new_master will be set to the second dead node and the new
master, then in dlm_reset_recovery(), these two variables will be reset
to default value.  This will cause new recovery master can not finish
the recovery process and hung, at last the whole cluster will hung for

old recovery master:                                 new recovery master:
                                                  become recovery master for
                                                  another dead node.
 if (dlm->reco.state & DLM_RECO_STATE_FINALIZE) {
  return -EAGAIN;
 dlm_set_reco_master(dlm, br->node_idx);
 dlm_set_reco_dead_node(dlm, br->dead_node);
 dlm_set_reco_dead_node(dlm, O2NM_INVALID_NODE_NUM);
 dlm_set_reco_master(dlm, O2NM_INVALID_NODE_NUM);
                                                  will hang in dlm_remaster_locks() for
                                                  request dlm locks info

Before send FINALIZE_RECO message, recovery master should set
DLM_RECO_STATE_FINALIZE for itself and clear it after the recovery done,
this can break the race windows as the BEGIN_RECO messages will not be
handled before DLM_RECO_STATE_FINALIZE flag is cleared.

A similar race may happen between new recovery master and normal node
which is in dlm_finalize_reco_handler(), also fix it.

Signed-off-by: Junxiao Bi <>
Reviewed-by: Srinivas Eeda <>
Reviewed-by: Wengang Wang <>
Cc: Joel Becker <>
Cc: Mark Fasheh <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
9 years agoocfs2: dlm: fix lock migration crash
Junxiao Bi [Thu, 3 Apr 2014 21:46:49 +0000 (14:46 -0700)]
ocfs2: dlm: fix lock migration crash

commit 34aa8dac482f1358d59110d5e3a12f4351f6acaa upstream.

This issue was introduced by commit 800deef3f6f8 ("ocfs2: use
list_for_each_entry where benefical") in 2007 where it replaced
list_for_each with list_for_each_entry.  The variable "lock" will point
to invalid data if "tmpq" list is empty and a panic will be triggered
due to this.  Sunil advised reverting it back, but the old version was
also not right.  At the end of the outer for loop, that
list_for_each_entry will also set "lock" to an invalid data, then in the
next loop, if the "tmpq" list is empty, "lock" will be an stale invalid
data and cause the panic.  So reverting the list_for_each back and reset
"lock" to NULL to fix this issue.

Another concern is that this seemes can not happen because the "tmpq"
list should not be empty.  Let me describe how.

old lock resource owner(node 1):                                  migratation target(node 2):
image there's lockres with a EX lock from node 2 in
granted list, a NR lock from node x with convert_type
EX in converting list.
dlm_empty_lockres() {
 dlm_pick_migration_target() {
   pick node 2 as target as its lock is the first one
   in granted list.
 dlm_migrate_lockres() {
   dlm_mark_lockres_migrating() {
     res->state |= DLM_LOCK_RES_BLOCK_DIRTY;
     wait_event(dlm->ast_wq, !dlm_lockres_is_dirty(dlm, res));
 //after the above code, we can not dirty lockres any more,
     // so dlm_thread shuffle list will not run
                                                                   downconvert lock from EX to NR
                                                                   upconvert lock from NR to EX
<<< migration may schedule out here, then
<<< node 2 send down convert request to convert type from EX to
<<< NR, then send up convert request to convert type from NR to
<<< EX, at this time, lockres granted list is empty, and two locks
<<< in the converting list, node x up convert lock followed by
<<< node 2 up convert lock.

 // will set lockres RES_MIGRATING flag, the following
 // lock/unlock can not run
     dlm_lockres_release_ast(dlm, res);

                                                                   for (i=0; i<mres->num_locks; i++)
                                                                     if (ml->node == dlm->node_num)
                                                                       for (j = DLM_GRANTED_LIST; j <= DLM_BLOCKED_LIST; j++) {
                                                                        list_for_each_entry(lock, tmpq, list)
                                                                        if (lock) break; <<< lock is invalid as grant list is empty.
                                                                       if (lock->ml.node != ml->node)
                                                                         BUG() >>> crash here

I see the above locks status from a vmcore of our internal bug.

Signed-off-by: Junxiao Bi <>
Reviewed-by: Wengang Wang <>
Cc: Sunil Mushran <>
Reviewed-by: Srinivas Eeda <>
Cc: Joel Becker <>
Cc: Mark Fasheh <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
9 years agosh: fix format string bug in stack tracer
Matt Fleming [Thu, 3 Apr 2014 21:46:20 +0000 (14:46 -0700)]
sh: fix format string bug in stack tracer

commit a0c32761e73c9999cbf592b702f284221fea8040 upstream.

Kees reported the following error:

   arch/sh/kernel/dumpstack.c: In function 'print_trace_address':
   arch/sh/kernel/dumpstack.c:118:2: error: format not a string literal and no format arguments [-Werror=format-security]

Use the "%s" format so that it's impossible to interpret 'data' as a
format string.

Signed-off-by: Matt Fleming <>
Reported-by: Kees Cook <>
Acked-by: Kees Cook <>
Cc: Paul Mundt <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
9 years agodrm/radeon: call drm_edid_to_eld when we update the edid
Alex Deucher [Mon, 31 Mar 2014 15:19:46 +0000 (11:19 -0400)]
drm/radeon: call drm_edid_to_eld when we update the edid

commit 16086279353cbfecbb3ead474072dced17b97ddc upstream.

This needs to be done to update some of the fields in
the connector structure used by the audio code.

Noticed by several users on irc.

Signed-off-by: Alex Deucher <>
Signed-off-by: Christian König <>
Signed-off-by: Ben Hutchings <>
9 years agodrm/vmwgfx: correct fb_fix_screeninfo.line_length
Christopher Friedt [Sat, 1 Feb 2014 15:01:15 +0000 (10:01 -0500)]
drm/vmwgfx: correct fb_fix_screeninfo.line_length

commit aa6de142c901cd2d90ef08db30ae87da214bedcc upstream.

Previously, the vmwgfx_fb driver would allow users to call FBIOSET_VINFO, but it would not adjust
the FINFO properly, resulting in distorted screen rendering. The patch corrects that behaviour.

See for examples.

Signed-off-by: Christopher Friedt <>
Reviewed-by: Thomas Hellstrom <>
Signed-off-by: Ben Hutchings <>
9 years agoreiserfs: fix race in readdir
Jeff Mahoney [Wed, 2 Apr 2014 18:40:26 +0000 (14:40 -0400)]
reiserfs: fix race in readdir

commit 01d8885785a60ae8f4c37b0ed75bdc96d0fc6a44 upstream.

jdm-20004 reiserfs_delete_xattrs: Couldn't delete all xattrs (-2)

The -ENOENT is due to readdir calling dir_emit on the same entry twice.

If the dir_emit callback sleeps and the tree is changed underneath us,
we won't be able to trust deh_offset(deh) anymore. We need to save
next_pos before we might sleep so we can find the next entry.

Signed-off-by: Jeff Mahoney <>
Signed-off-by: Jan Kara <>
Signed-off-by: Ben Hutchings <>
9 years agoIB/ehca: Returns an error on ib_copy_to_udata() failure
Yann Droneaud [Mon, 10 Mar 2014 22:06:25 +0000 (23:06 +0100)]
IB/ehca: Returns an error on ib_copy_to_udata() failure

commit 5bdb0f02add5994b0bc17494f4726925ca5d6ba1 upstream.

In case of error when writing to userspace, function ehca_create_cq()
does not set an error code before following its error path.

This patch sets the error code to -EFAULT when ib_copy_to_udata()

This was caught when using spatch (aka. coccinelle)
to rewrite call to ib_copy_{from,to}_udata().

Signed-off-by: Yann Droneaud <>
Signed-off-by: Roland Dreier <>
Signed-off-by: Ben Hutchings <>
9 years agoIB/mthca: Return an error on ib_copy_to_udata() failure
Yann Droneaud [Mon, 10 Mar 2014 22:06:26 +0000 (23:06 +0100)]
IB/mthca: Return an error on ib_copy_to_udata() failure

commit 08e74c4b00c30c232d535ff368554959403d0432 upstream.

In case of error when writing to userspace, the function mthca_create_cq()
does not set an error code before following its error path.

This patch sets the error code to -EFAULT when ib_copy_to_udata() fails.

This was caught when using spatch (aka. coccinelle)
to rewrite call to ib_copy_{from,to}_udata().

Signed-off-by: Yann Droneaud <>
Signed-off-by: Roland Dreier <>
Signed-off-by: Ben Hutchings <>
9 years agoALSA: hda - Enable beep for ASUS 1015E
W. Trevor King [Sun, 30 Mar 2014 00:47:24 +0000 (17:47 -0700)]
ALSA: hda - Enable beep for ASUS 1015E

commit a4b7f21d7b42b33609df3f86992a8deff80abfaf upstream.

The `lspci -nnvv` output contains (wrapped for line length):

  00:1b.0 Audio device [0403]:
    Intel Corporation 7 Series/C210 Series Chipset Family
    High Definition Audio Controller [8086:1e20] (rev 04)
        Subsystem: ASUSTeK Computer Inc. Device [1043:115d]

Signed-off-by: W. Trevor King <>
Signed-off-by: Takashi Iwai <>
Signed-off-by: Ben Hutchings <>
9 years agoMIPS: Hibernate: Flush TLB entries in swsusp_arch_resume()
Huacai Chen [Sat, 22 Mar 2014 09:21:44 +0000 (17:21 +0800)]
MIPS: Hibernate: Flush TLB entries in swsusp_arch_resume()

commit c14af233fbe279d0e561ecf84f1208b1bae087ef upstream.

The original MIPS hibernate code flushes cache and TLB entries in
swsusp_arch_resume(). But they are removed in Commit 44eeab67416711
(MIPS: Hibernation: Remove SMP TLB and cacheflushing code.). A cross-
CPU flush is surely unnecessary because all but the local CPU have
already been disabled. But a local flush (at least the TLB flush) is
needed. When we do hibernation on Loongson-3 with an E1000E NIC, it is
very easy to produce a kernel panic (kernel page fault, or unaligned
access). The root cause is E1000E driver use vzalloc_node() to allocate
pages, the stale TLB entries of the booting kernel will be misused by
the resumed target kernel.

Signed-off-by: Huacai Chen <>
Cc: John Crispin <>
Cc: Steven J. Hill <>
Cc: Aurelien Jarno <>
Cc: Fuxin Zhang <>
Cc: Zhangjin Wu <>
Signed-off-by: Ralf Baechle <>
Signed-off-by: Ben Hutchings <>
9 years agonfsd4: fix setclientid encode size
J. Bruce Fields [Mon, 10 Mar 2014 18:17:55 +0000 (14:17 -0400)]
nfsd4: fix setclientid encode size

commit 480efaee085235bb848f1063f959bf144103c342 upstream.

Signed-off-by: J. Bruce Fields <>
Signed-off-by: Ben Hutchings <>
9 years agodm thin: fix dangling bio in process_deferred_bios error path
Mike Snitzer [Fri, 28 Mar 2014 06:15:02 +0000 (02:15 -0400)]
dm thin: fix dangling bio in process_deferred_bios error path

commit fe76cd88e654124d1431bb662a0fc6e99ca811a5 upstream.

If unable to ensure_next_mapping() we must add the current bio, which
was removed from the @bios list via bio_list_pop, back to the
deferred_bios list before all the remaining @bios.

Signed-off-by: Mike Snitzer <>
Acked-by: Joe Thornber <>
Signed-off-by: Ben Hutchings <>
9 years agodrm/i915/tv: fix gen4 composite s-video tv-out
Jani Nikula [Fri, 28 Mar 2014 06:54:04 +0000 (08:54 +0200)]
drm/i915/tv: fix gen4 composite s-video tv-out

commit e1f23f3dd817f53f622e486913ac662add46eeed upstream.

This is *not* bisected, but the likely regression is

commit c35614380d5c956bfda20eab2755b2f5a7d6f1e7
Author: Zhao Yakui <>
Date:   Tue Nov 24 09:48:48 2009 +0800

    drm/i915: Don't set up the TV port if it isn't in the BIOS table.

The commit does not check for all TV device types that might be present
in the VBT, disabling TV out for the missing ones. Add composite

Reported-and-tested-by: Matthew Khouzam <>
Signed-off-by: Jani Nikula <>
Signed-off-by: Daniel Vetter <>
[bwh: Backported to 3.2: s/old\.device_type/device_type/]
Signed-off-by: Ben Hutchings <>
9 years agonfsd: notify_change needs elevated write count
J. Bruce Fields [Mon, 24 Feb 2014 19:59:47 +0000 (14:59 -0500)]
nfsd: notify_change needs elevated write count

commit 9f67f189939eccaa54f3d2c9cf10788abaf2d584 upstream.

Looks like this bug has been here since these write counts were
introduced, not sure why it was just noticed now.

Thanks also to Jan Kara for pointing out the problem.

Reported-by: Matthew Rahtz <>
Signed-off-by: J. Bruce Fields <>
Signed-off-by: Ben Hutchings <>
9 years agonfsd: Add fh_{want,drop}_write()
Ben Hutchings [Sun, 27 Apr 2014 00:20:19 +0000 (01:20 +0100)]
nfsd: Add fh_{want,drop}_write()

Part of commit bad0dcffc21d17a07dbb83a2bf764f35a57feba5
('new helpers: fh_{want,drop}_write()') upstream.

Signed-off-by: Ben Hutchings <>
9 years agonfsd4: session needs room for following op to error out
J. Bruce Fields [Tue, 28 Jan 2014 21:01:04 +0000 (16:01 -0500)]
nfsd4: session needs room for following op to error out

commit 4c69d5855a16f7378648c5733632628fa10431db upstream.

Signed-off-by: J. Bruce Fields <>
Signed-off-by: Ben Hutchings <>
9 years agonfsd4: buffer-length check for SUPPATTR_EXCLCREAT
J. Bruce Fields [Tue, 28 Jan 2014 21:05:15 +0000 (16:05 -0500)]
nfsd4: buffer-length check for SUPPATTR_EXCLCREAT

commit de3997a7eeb9ea286b15879fdf8a95aae065b4f7 upstream.

This was an omission from 8c18f2052e756e7d5dea712fc6e7ed70c00e8a39
"nfsd41: SUPPATTR_EXCLCREAT attribute".

Cc: Benny Halevy <>
Signed-off-by: J. Bruce Fields <>
Signed-off-by: Ben Hutchings <>
9 years agox86, hyperv: Bypass the timer_irq_works() check
Jason Wang [Fri, 28 Feb 2014 03:30:29 +0000 (11:30 +0800)]
x86, hyperv: Bypass the timer_irq_works() check

commit ca3ba2a2f4a49a308e7d78c784d51b2332064f15 upstream.

This patch bypass the timer_irq_works() check for hyperv guest since:

- It was guaranteed to work.
- timer_irq_works() may fail sometime due to the lpj calibration were inaccurate
  in a hyperv guest or a buggy host.

In the future, we should get the tsc frequency from hypervisor and use preset
lpj instead.

[ hpa: I would prefer to not defer things to "the future" in the future... ]

Cc: K. Y. Srinivasan <>
Cc: Haiyang Zhang <>
Acked-by: K. Y. Srinivasan <>
Signed-off-by: Jason Wang <>
Signed-off-by: H. Peter Anvin <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agogpio: mxs: Allow for recursive enable_irq_wake() call
Marek Vasut [Mon, 24 Mar 2014 02:38:10 +0000 (03:38 +0100)]
gpio: mxs: Allow for recursive enable_irq_wake() call

commit a585f87c863e4e1d496459d382b802bf5ebe3717 upstream.

The scenario here is that someone calls enable_irq_wake() from somewhere
in the code. This will result in the lockdep producing a backtrace as can
be seen below. In my case, this problem is triggered when using the wl1271
(TI WlCore) driver found in drivers/net/wireless/ti/ .

The problem cause is rather obvious from the backtrace, but let's outline
the dependency. enable_irq_wake() grabs the IRQ buslock in irq_set_irq_wake(),
which in turns calls mxs_gpio_set_wake_irq() . But mxs_gpio_set_wake_irq()
calls enable_irq_wake() again on the one-level-higher IRQ , thus it tries to
grab the IRQ buslock again in irq_set_irq_wake() . Because the spinlock in
irq_set_irq_wake()->irq_get_desc_buslock()->__irq_get_desc_lock() is not
marked as recursive, lockdep will spew the stuff below.

We know we can safely re-enter the lock, so use IRQ_GC_INIT_NESTED_LOCK to
fix the spew.

 [ INFO: possible recursive locking detected ]
 3.10.33-00012-gf06b763-dirty #61 Not tainted
 kworker/0:1/18 is trying to acquire lock:
  (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88

 but task is already holding lock:
  (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88

 other info that might help us debug this:
  Possible unsafe locking scenario:


  *** DEADLOCK ***

  May be due to missing lock nesting notation

 3 locks held by kworker/0:1/18:
  #0:  (events){.+.+.+}, at: [<c0036308>] process_one_work+0x134/0x4a4
  #1:  ((&fw_work->work)){+.+.+.}, at: [<c0036308>] process_one_work+0x134/0x4a4
  #2:  (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88

 stack backtrace:
 CPU: 0 PID: 18 Comm: kworker/0:1 Not tainted 3.10.33-00012-gf06b763-dirty #61
 Workqueue: events request_firmware_work_func
 [<c0013eb4>] (unwind_backtrace+0x0/0xf0) from [<c0011c74>] (show_stack+0x10/0x14)
 [<c0011c74>] (show_stack+0x10/0x14) from [<c005bb08>] (__lock_acquire+0x140c/0x1a64)
 [<c005bb08>] (__lock_acquire+0x140c/0x1a64) from [<c005c6a8>] (lock_acquire+0x9c/0x104)
 [<c005c6a8>] (lock_acquire+0x9c/0x104) from [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58)
 [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58) from [<c00685f0>] (__irq_get_desc_lock+0x48/0x88)
 [<c00685f0>] (__irq_get_desc_lock+0x48/0x88) from [<c0068e78>] (irq_set_irq_wake+0x20/0xf4)
 [<c0068e78>] (irq_set_irq_wake+0x20/0xf4) from [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24)
 [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24) from [<c0068cf4>] (set_irq_wake_real+0x30/0x44)
 [<c0068cf4>] (set_irq_wake_real+0x30/0x44) from [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4)
 [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4) from [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c)
 [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c) from [<c02be5e8>] (request_firmware_work_func+0x38/0x58)
 [<c02be5e8>] (request_firmware_work_func+0x38/0x58) from [<c0036394>] (process_one_work+0x1c0/0x4a4)
 [<c0036394>] (process_one_work+0x1c0/0x4a4) from [<c0036a4c>] (worker_thread+0x138/0x394)
 [<c0036a4c>] (worker_thread+0x138/0x394) from [<c003cb74>] (kthread+0xa4/0xb0)
 [<c003cb74>] (kthread+0xa4/0xb0) from [<c000ee00>] (ret_from_fork+0x14/0x34)
 wlcore: loaded

Signed-off-by: Marek Vasut <>
Acked-by: Shawn Guo <>
Signed-off-by: Linus Walleij <>
Signed-off-by: Ben Hutchings <>
9 years agoBtrfs: fix deadlock with nested trans handles
Josef Bacik [Fri, 7 Mar 2014 00:01:07 +0000 (19:01 -0500)]
Btrfs: fix deadlock with nested trans handles

commit 3bbb24b20a8800158c33eca8564f432dd14d0bf3 upstream.

Zach found this deadlock that would happen like this

btrfs_end_transaction <- reduce trans->use_count to 0
btrfs_start_transaction <- increase trans->use_count to 1
          allocate chunk
btrfs_end_transaction <- decrease trans->use_count to 0
    lock tree block we are cowing above ^^

We need to only decrease trans->use_count if it is above 1, otherwise leave it
alone.  This will make nested trans be the only ones who decrease their added
ref, and will let us get rid of the trans->use_count++ hack if we have to commit
the transaction.  Thanks,

Reported-by: Zach Brown <>
Signed-off-by: Josef Bacik <>
Tested-by: Zach Brown <>
Signed-off-by: Chris Mason <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoaudit: convert PPIDs to the inital PID namespace.
Richard Guy Briggs [Wed, 11 Dec 2013 03:10:41 +0000 (22:10 -0500)]
audit: convert PPIDs to the inital PID namespace.

commit c92cdeb45eea38515e82187f48c2e4f435fb4e25 upstream.

sys_getppid() returns the parent pid of the current process in its own pid
namespace.  Since audit filters are based in the init pid namespace, a process
could avoid a filter or trigger an unintended one by being in an alternate pid
namespace or log meaningless information.

Switch to task_ppid_nr() for PPIDs to anchor all audit filters in the

(informed by ebiederman's 6c621b7e)
Cc: Eric W. Biederman <>
Signed-off-by: Richard Guy Briggs <>
[bwh: Backported to 3.2: sys_getppid() is used by audit_exit() but not
Signed-off-by: Ben Hutchings <>
9 years agopid: get pid_t ppid of task in init_pid_ns
Richard Guy Briggs [Thu, 15 Aug 2013 22:05:12 +0000 (18:05 -0400)]
pid: get pid_t ppid of task in init_pid_ns

commit ad36d28293936b03d6b7996e9d6aadfd73c0eb08 upstream.

Added the functions task_ppid_nr_ns() and task_ppid_nr() to abstract the lookup
of the PPID (real_parent's pid_t) of a process, including rcu locking, in the
arbitrary and init_pid_ns.
This provides an alternative to sys_getppid(), which is relative to the child
process' pid namespace.

(informed by ebiederman's 6c621b7e)
Cc: Eric W. Biederman <>
Signed-off-by: Richard Guy Briggs <>
Signed-off-by: Ben Hutchings <>
9 years agomfd: 88pm860x: Fix possible NULL pointer dereference on i2c_new_dummy error
Krzysztof Kozlowski [Tue, 11 Feb 2014 10:03:29 +0000 (11:03 +0100)]
mfd: 88pm860x: Fix possible NULL pointer dereference on i2c_new_dummy error

commit 159ce52a6b777fc82fa0b51c7440e25f9e4c6feb upstream.

During probe the driver allocates dummy I2C device for companion chip
with i2c_new_dummy() but it does not check the return value of this call.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by regmap_init_i2c().

If i2c_new_dummy() fails for companion device, fail also the probe for
main MFD driver.

Signed-off-by: Krzysztof Kozlowski <>
Signed-off-by: Lee Jones <>
[bwh: Backported to 3.2:
 - Adjust filename, context
 - Add kfree() before return, as driver is not using managed allocations]
Signed-off-by: Ben Hutchings <>
9 years agomfd: max8925: Fix possible NULL pointer dereference on i2c_new_dummy error
Krzysztof Kozlowski [Tue, 11 Feb 2014 10:03:33 +0000 (11:03 +0100)]
mfd: max8925: Fix possible NULL pointer dereference on i2c_new_dummy error

commit 96cf3dedc491d2f1f66cc26217f2b06b0c7b6797 upstream.

During probe the driver allocates dummy I2C devices for RTC and ADC
with i2c_new_dummy() but it does not check the return value of this

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC or ADC devices, fail also the probe
for main MFD driver.

Signed-off-by: Krzysztof Kozlowski <>
Signed-off-by: Lee Jones <>
Signed-off-by: Ben Hutchings <>
9 years agomfd: max8998: Fix possible NULL pointer dereference on i2c_new_dummy error
Krzysztof Kozlowski [Tue, 11 Feb 2014 10:03:35 +0000 (11:03 +0100)]
mfd: max8998: Fix possible NULL pointer dereference on i2c_new_dummy error

commit ed26f87b9f71693a1d1ee85f5e6209601505080f upstream.

During probe the driver allocates dummy I2C device for RTC with i2c_new_dummy() but it does not check the return value of this call.

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC device, fail also the probe for
main MFD driver.

Signed-off-by: Krzysztof Kozlowski <>
Signed-off-by: Lee Jones <>
Signed-off-by: Ben Hutchings <>
9 years agomfd: max8997: Fix possible NULL pointer dereference on i2c_new_dummy error
Krzysztof Kozlowski [Tue, 11 Feb 2014 10:03:34 +0000 (11:03 +0100)]
mfd: max8997: Fix possible NULL pointer dereference on i2c_new_dummy error

commit 97dc4ed3fa377ec91bb60ba98b70d645c2099384 upstream.

During probe the driver allocates dummy I2C devices for RTC, haptic and
MUIC with i2c_new_dummy() but it does not check the return value of this

In case of error (i2c_new_device(): memory allocation failure or I2C
address cannot be used) this function returns NULL which is later used
by i2c_unregister_device().

If i2c_new_dummy() fails for RTC, haptic or MUIC devices, fail also the
probe for main MFD driver.

Signed-off-by: Krzysztof Kozlowski <>
Signed-off-by: Lee Jones <>
Signed-off-by: Ben Hutchings <>
9 years agomfd: Include all drivers in subsystem menu
Linus Walleij [Wed, 29 Jan 2014 10:09:53 +0000 (11:09 +0100)]
mfd: Include all drivers in subsystem menu

commit a6e6e660baa5c583022e3e48c85316bace027825 upstream.

It is currently not possible to select the SA1100 or Vexpress
drivers in the MFD subsystem, because the menu for the entire
subsystem ends before these options are presented.

Move the main menu closing and the endif for HAS_IOMEM to the
end of the file so these are selectable again.

Signed-off-by: Linus Walleij <>
Signed-off-by: Lee Jones <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoIB/nes: Return an error on ib_copy_from_udata() failure instead of NULL
Yann Droneaud [Mon, 10 Mar 2014 22:06:27 +0000 (23:06 +0100)]
IB/nes: Return an error on ib_copy_from_udata() failure instead of NULL

commit 9d194d1025f463392feafa26ff8c2d8247f71be1 upstream.

In case of error while accessing to userspace memory, function
nes_create_qp() returns NULL instead of an error code wrapped through
ERR_PTR().  But NULL is not expected by ib_uverbs_create_qp(), as it
check for error with IS_ERR().

As page 0 is likely not mapped, it is going to trigger an Oops when
the kernel will try to dereference NULL pointer to access to struct
ib_qp's fields.

In some rare cases, page 0 could be mapped by userspace, which could
turn this bug to a vulnerability that could be exploited: the function
pointers in struct ib_device will be under userspace total control.

This was caught when using spatch (aka. coccinelle)
to rewrite calls to ib_copy_{from,to}_udata().

Signed-off-by: Yann Droneaud <>
Signed-off-by: Roland Dreier <>
Signed-off-by: Ben Hutchings <>
9 years agoIB/ipath: Fix potential buffer overrun in sending diag packet routine
Dennis Dalessandro [Thu, 20 Feb 2014 16:02:53 +0000 (11:02 -0500)]
IB/ipath: Fix potential buffer overrun in sending diag packet routine

commit a2cb0eb8a64adb29a99fd864013de957028f36ae upstream.

Guard against a potential buffer overrun.  The size to read from the
user is passed in, and due to the padding that needs to be taken into
account, as well as the place holder for the ICRC it is possible to
overflow the 32bit value which would cause more data to be copied from
user space than is allocated in the buffer.

Reported-by: Nico Golde <>
Reported-by: Fabian Yamaguchi <>
Reviewed-by: Mike Marciniszyn <>
Signed-off-by: Dennis Dalessandro <>
Signed-off-by: Roland Dreier <>
Signed-off-by: Ben Hutchings <>
9 years agoath9k: fix ready time of the multicast buffer queue
Felix Fietkau [Sun, 9 Mar 2014 10:02:54 +0000 (11:02 +0100)]
ath9k: fix ready time of the multicast buffer queue

commit 3b3e0efb5c72c4fc940af50b33626b8a78a907dc upstream.

qi->tqi_readyTime is written directly to registers that expect
microseconds as unit instead of TU.
When setting the CABQ ready time, cur_conf->beacon_interval is in TU, so
convert it to microseconds before passing it to ath9k_hw.

This should hopefully fix some Tx DMA issues with buffered multicast
frames in AP mode.

Signed-off-by: Felix Fietkau <>
Signed-off-by: John W. Linville <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agoext4: fix partial cluster handling for bigalloc file systems
Eric Whitney [Fri, 14 Mar 2014 03:34:16 +0000 (23:34 -0400)]
ext4: fix partial cluster handling for bigalloc file systems

commit c06344939422bbd032ac967223a7863de57496b5 upstream.

Commit 9cb00419fa, which enables hole punching for bigalloc file
systems, exposed a bug introduced by commit 6ae06ff51e in an earlier
release.  When run on a bigalloc file system, xfstests generic/013, 068,
075, 083, 091, 100, 112, 127, 263, 269, and 270 fail with e2fsck errors
or cause kernel error messages indicating that previously freed blocks
are being freed again.

The latter commit optimizes the selection of the starting extent in
ext4_ext_rm_leaf() when hole punching by beginning with the extent
supplied in the path argument rather than with the last extent in the
leaf node (as is still done when truncating).  However, the code in
rm_leaf that initially sets partial_cluster to track cluster sharing on
extent boundaries is only guaranteed to run if rm_leaf starts with the
last node in the leaf.  Consequently, partial_cluster is not correctly
initialized when hole punching, and a cluster on the boundary of a
punched region that should be retained may instead be deallocated.

Signed-off-by: Eric Whitney <>
Signed-off-by: "Theodore Ts'o" <>
Signed-off-by: Ben Hutchings <>
9 years agovirtio_balloon: don't softlockup on huge balloon changes.
Rusty Russell [Thu, 13 Mar 2014 00:53:38 +0000 (11:23 +1030)]
virtio_balloon: don't softlockup on huge balloon changes.

commit 1f74ef0f2d7d692fcd615621e0e734c3e7771413 upstream.

When adding or removing 100G from a balloon:

    BUG: soft lockup - CPU#0 stuck for 22s! [vballoon:367]

We have a wait_event_interruptible(), but the condition is always true
(more ballooning to do) so we don't ever sleep.  We also have a
wait_event() for the host to ack, but that is also always true as QEMU
is synchronous for balloon operations.

Reported-by: Gopesh Kumar Chaudhary <>
Signed-off-by: Rusty Russell <>
Signed-off-by: Ben Hutchings <>
9 years agoiwlwifi: dvm: take mutex when sending SYNC BT config command
Emmanuel Grumbach [Mon, 10 Mar 2014 13:22:03 +0000 (15:22 +0200)]
iwlwifi: dvm: take mutex when sending SYNC BT config command

commit 82e5a649453a3cf23516277abb84273768a1592b upstream.

There is a flow in which we send the host command in SYNC
mode, but we don't take priv->mutex.


Reviewed-by: Johannes Berg <>
Signed-off-by: Emmanuel Grumbach <>
[bwh: Backported to 3.2:
 - Adjust filename, context
 - mutex is priv->shrd->mutex]
Signed-off-by: Ben Hutchings <>
9 years agojffs2: Fix crash due to truncation of csize
Ajesh Kunhipurayil Vijayan [Mon, 6 Jan 2014 13:36:55 +0000 (19:06 +0530)]
jffs2: Fix crash due to truncation of csize

commit 41bf1a24c1001f4d0d41a78e1ac575d2f14789d7 upstream.

mounting JFFS2 partition sometimes crashes with this call trace:

[ 1322.240000] Kernel bug detected[#1]:
[ 1322.244000] Cpu 2
[ 1322.244000] $ 0   : 0000000000000000 0000000000000018 000000003ff00070 0000000000000001
[ 1322.252000] $ 4   : 0000000000000000 c0000000f3980150 0000000000000000 0000000000010000
[ 1322.260000] $ 8   : ffffffffc09cd5f8 0000000000000001 0000000000000088 c0000000ed300de8
[ 1322.268000] $12   : e5e19d9c5f613a45 ffffffffc046d464 0000000000000000 66227ba5ea67b74e
[ 1322.276000] $16   : c0000000f1769c00 c0000000ed1e0200 c0000000f3980150 0000000000000000
[ 1322.284000] $20   : c0000000f3a80000 00000000fffffffc c0000000ed2cfbd8 c0000000f39818f0
[ 1322.292000] $24   : 0000000000000004 0000000000000000
[ 1322.300000] $28   : c0000000ed2c0000 c0000000ed2cfab8 0000000000010000 ffffffffc039c0b0
[ 1322.308000] Hi    : 000000000000023c
[ 1322.312000] Lo    : 000000000003f802
[ 1322.316000] epc   : ffffffffc039a9f8 check_tn_node+0x88/0x3b0
[ 1322.320000]     Not tainted
[ 1322.324000] ra    : ffffffffc039c0b0 jffs2_do_read_inode_internal+0x1250/0x1e48
[ 1322.332000] Status: 5400f8e3    KX SX UX KERNEL EXL IE
[ 1322.336000] Cause : 00800034
[ 1322.340000] PrId  : 000c1004 (Netlogic XLP)
[ 1322.344000] Modules linked in:
[ 1322.348000] Process jffs2_gcd_mtd7 (pid: 264, threadinfo=c0000000ed2c0000, task=c0000000f0e68dd8, tls=0000000000000000)
[ 1322.356000] Stack : c0000000f1769e30 c0000000ed010780 c0000000ed010780 c0000000ed300000
        c0000000f1769c00 c0000000f3980150 c0000000f3a80000 00000000fffffffc
        c0000000ed2cfbd8 ffffffffc039c0b0 ffffffffc09c6340 0000000000001000
        0000000000000dec ffffffffc016c9d8 c0000000f39805a0 c0000000f3980180
        0000008600000000 0000000000000000 0000000000000000 0000000000000000
        0001000000000dec c0000000f1769d98 c0000000ed2cfb18 0000000000010000
        0000000000010000 0000000000000044 c0000000f3a80000 c0000000f1769c00
        c0000000f3d207a8 c0000000f1769d98 c0000000f1769de0 ffffffffc076f9c0
        0000000000000009 0000000000000000 0000000000000000 ffffffffc039cf90
        0000000000000017 ffffffffc013fbdc 0000000000000001 000000010003e61c
[ 1322.424000] Call Trace:
[ 1322.428000] [<ffffffffc039a9f8>] check_tn_node+0x88/0x3b0
[ 1322.432000] [<ffffffffc039c0b0>] jffs2_do_read_inode_internal+0x1250/0x1e48
[ 1322.440000] [<ffffffffc039cf90>] jffs2_do_crccheck_inode+0x70/0xd0
[ 1322.448000] [<ffffffffc03a1b80>] jffs2_garbage_collect_pass+0x160/0x870
[ 1322.452000] [<ffffffffc03a392c>] jffs2_garbage_collect_thread+0xdc/0x1f0
[ 1322.460000] [<ffffffffc01541c8>] kthread+0xb8/0xc0
[ 1322.464000] [<ffffffffc0106d18>] kernel_thread_helper+0x10/0x18
[ 1322.472000]
[ 1322.472000]
Code: 67bd0050  94a4002c  2c830001 <00038036de050218  2403fffc  0080a82d  00431824  24630044
[ 1322.480000] ---[ end trace b052bb90e97dfbf5 ]---

The variable csize in structure jffs2_tmp_dnode_info is of type uint16_t, but it
is used to hold the compressed data length(csize) which is declared as uint32_t.
So, when the value of csize exceeds 16bits, it gets truncated when assigned to
tn->csize. This is causing a kernel BUG.
Changing the definition of csize in jffs2_tmp_dnode_info to uint32_t fixes the issue.

Signed-off-by: Ajesh Kunhipurayil Vijayan <>
Signed-off-by: Kamlakant Patel <>
Signed-off-by: Brian Norris <>
Signed-off-by: Ben Hutchings <>
9 years agojffs2: Fix segmentation fault found in stress test
Kamlakant Patel [Mon, 6 Jan 2014 13:36:54 +0000 (19:06 +0530)]
jffs2: Fix segmentation fault found in stress test

commit 3367da5610c50e6b83f86d366d72b41b350b06a2 upstream.

Creating a large file on a JFFS2 partition sometimes crashes with this call

[  306.476000] CPU 13 Unable to handle kernel paging request at virtual address c0000000dfff8002, epc == ffffffffc03a80a8, ra == ffffffffc03a8044
[  306.488000] Oops[#1]:
[  306.488000] Cpu 13
[  306.492000] $ 0   : 0000000000000000 0000000000000000 0000000000008008 0000000000008007
[  306.500000] $ 4   : c0000000dfff8002 000000000000009f c0000000e0007cde c0000000ee95fa58
[  306.508000] $ 8   : 0000000000000001 0000000000008008 0000000000010000 ffffffffffff8002
[  306.516000] $12   : 0000000000007fa9 000000000000ff0e 000000000000ff0f 80e55930aebb92bb
[  306.524000] $16   : c0000000e0000000 c0000000ee95fa5c c0000000efc80000 ffffffffc09edd70
[  306.532000] $20   : ffffffffc2b60000 c0000000ee95fa58 0000000000000000 c0000000efc80000
[  306.540000] $24   : 0000000000000000 0000000000000004
[  306.548000] $28   : c0000000ee950000 c0000000ee95f738 0000000000000000 ffffffffc03a8044
[  306.556000] Hi    : 00000000000574a5
[  306.560000] Lo    : 6193b7a7e903d8c9
[  306.564000] epc   : ffffffffc03a80a8 jffs2_rtime_compress+0x98/0x198
[  306.568000]     Tainted: G        W
[  306.572000] ra    : ffffffffc03a8044 jffs2_rtime_compress+0x34/0x198
[  306.580000] Status: 5000f8e3    KX SX UX KERNEL EXL IE
[  306.584000] Cause : 00800008
[  306.588000] BadVA : c0000000dfff8002
[  306.592000] PrId  : 000c1100 (Netlogic XLP)
[  306.596000] Modules linked in:
[  306.596000] Process dd (pid: 170, threadinfo=c0000000ee950000, task=c0000000ee6e0858, tls=0000000000c47490)
[  306.608000] Stack : 7c547f377ddc7ee4 7ffc7f967f5d7fae 7f617f507fc37ff4 7e7d7f817f487f5f
        7d8e7fec7ee87eb3 7e977ff27eec7f9e 7d677ec67f917f67 7f3d7e457f017ed7
        7fd37f517f867eb2 7fed7fd17ca57e1d 7e5f7fe87f257f77 7fd77f0d7ede7fdb
        7fba7fef7e197f99 7fde7fe07ee37eb5 7f5c7f8c7fc67f65 7f457fb87f847e93
        7f737f3e7d137cd9 7f8e7e9c7fc47d25 7dbb7fac7fb67e52 7ff17f627da97f64
        7f6b7df77ffa7ec5 80057ef17f357fb3 7f767fa27dfc7fd5 7fe37e8e7fd07e53
        7e227fcf7efb7fa1 7f547e787fa87fcc 7fcb7fc57f5a7ffb 7fc07f6c7ea97e80
        7e2d7ed17e587ee0 7fb17f9d7feb7f31 7f607e797e887faa 7f757fdd7c607ff3
        7e877e657ef37fbd 7ec17fd67fe67ff7 7ff67f797ff87dc4 7eef7f3a7c337fa6
        7fe57fc97ed87f4b 7ebe7f097f0b8003 7fe97e2a7d997cba 7f587f987f3c7fa9
[  306.676000] Call Trace:
[  306.680000] [<ffffffffc03a80a8>] jffs2_rtime_compress+0x98/0x198
[  306.684000] [<ffffffffc0394f10>] jffs2_selected_compress+0x110/0x230
[  306.692000] [<ffffffffc039508c>] jffs2_compress+0x5c/0x388
[  306.696000] [<ffffffffc039dc58>] jffs2_write_inode_range+0xd8/0x388
[  306.704000] [<ffffffffc03971bc>] jffs2_write_end+0x16c/0x2d0
[  306.708000] [<ffffffffc01d3d90>] generic_file_buffered_write+0xf8/0x2b8
[  306.716000] [<ffffffffc01d4e7c>] __generic_file_aio_write+0x1ac/0x350
[  306.720000] [<ffffffffc01d50a0>] generic_file_aio_write+0x80/0x168
[  306.728000] [<ffffffffc021f7dc>] do_sync_write+0x94/0xf8
[  306.732000] [<ffffffffc021ff6c>] vfs_write+0xa4/0x1a0
[  306.736000] [<ffffffffc02202e8>] SyS_write+0x50/0x90
[  306.744000] [<ffffffffc0116cc0>] handle_sys+0x180/0x1a0
[  306.748000]
[  306.748000]
Code: 020b202d  0205282d  90a50000 <9084000014a40038  00000000  0060602d  0000282d  016c5823
[  306.760000] ---[ end trace 79dd088435be02d0 ]---
Segmentation fault

This crash is caused because the 'positions' is declared as an array of signed
short. The value of position is in the range 0..65535, and will be converted
to a negative number when the position is greater than 32767 and causes a
corruption and crash. Changing the definition to 'unsigned short' fixes this

Signed-off-by: Jayachandran C <>
Signed-off-by: Kamlakant Patel <>
Signed-off-by: Brian Norris <>
Signed-off-by: Ben Hutchings <>
9 years agojffs2: avoid soft-lockup in jffs2_reserve_space_gc()
Li Zefan [Wed, 12 Feb 2014 20:44:56 +0000 (12:44 -0800)]
jffs2: avoid soft-lockup in jffs2_reserve_space_gc()

commit 13b546d96207c131eeae15dc7b26c6e7d0f1cad7 upstream.

We triggered soft-lockup under stress test on 2.6.34 kernel.

BUG: soft lockup - CPU#1 stuck for 60009ms! [lockf2.test:14488]
[<bf09a4d4>] (jffs2_do_reserve_space+0x420/0x440 [jffs2])
[<bf09a528>] (jffs2_reserve_space_gc+0x34/0x78 [jffs2])
[<bf0a1350>] (jffs2_garbage_collect_dnode.isra.3+0x264/0x478 [jffs2])
[<bf0a2078>] (jffs2_garbage_collect_pass+0x9c0/0xe4c [jffs2])
[<bf09a670>] (jffs2_reserve_space+0x104/0x2a8 [jffs2])
[<bf09dc48>] (jffs2_write_inode_range+0x5c/0x4d4 [jffs2])
[<bf097d8c>] (jffs2_write_end+0x198/0x2c0 [jffs2])
[<c00e00a4>] (generic_file_buffered_write+0x158/0x200)
[<c00e14f4>] (__generic_file_aio_write+0x3a4/0x414)
[<c00e15c0>] (generic_file_aio_write+0x5c/0xbc)
[<c012334c>] (do_sync_write+0x98/0xd4)
[<c0123a84>] (vfs_write+0xa8/0x150)
[<c0123d74>] (sys_write+0x3c/0xc0)]

Fix this by adding a cond_resched() in the while loop.

[ don't initialize `ret']
Signed-off-by: Li Zefan <>
Cc: David Woodhouse <>
Cc: Artem Bityutskiy <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Brian Norris <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agojffs2: remove from wait queue after schedule()
Li Zefan [Wed, 12 Feb 2014 20:44:57 +0000 (12:44 -0800)]
jffs2: remove from wait queue after schedule()

commit 3ead9578443b66ddb3d50ed4f53af8a0c0298ec5 upstream.

@wait is a local variable, so if we don't remove it from the wait queue
list, later wake_up() may end up accessing invalid memory.

This was spotted by eyes.

Signed-off-by: Li Zefan <>
Cc: David Woodhouse <>
Cc: Artem Bityutskiy <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Brian Norris <>
Signed-off-by: Ben Hutchings <>
9 years agoBtrfs: skip submitting barrier for missing device
Hidetoshi Seto [Wed, 5 Feb 2014 07:34:38 +0000 (16:34 +0900)]
Btrfs: skip submitting barrier for missing device

commit f88ba6a2a44ee98e8d59654463dc157bb6d13c43 upstream.

I got an error on v3.13:
 BTRFS error (device sdf1) in write_all_supers:3378: errno=-5 IO failure (errors while submitting device barriers.)

how to reproduce:
  > mkfs.btrfs -f -d raid1 /dev/sdf1 /dev/sdf2
  > wipefs -a /dev/sdf2
  > mount -o degraded /dev/sdf1 /mnt
  > btrfs balance start -f -sconvert=single -mconvert=single -dconvert=single /mnt

The reason of the error is that barrier_all_devices() failed to submit
barrier to the missing device.  However it is clear that we cannot do
anything on missing device, and also it is not necessary to care chunks
on the missing device.

This patch stops sending/waiting barrier if device is missing.

Signed-off-by: Hidetoshi Seto <>
Signed-off-by: Josef Bacik <>
Signed-off-by: Ben Hutchings <>
9 years agostaging:serqt_usb2: Fix sparse warning restricted __le16 degrades to integer
Himangi Saraogi [Tue, 4 Mar 2014 23:29:57 +0000 (04:59 +0530)]
staging:serqt_usb2: Fix sparse warning restricted __le16 degrades to integer

commit abe5d64d1a74195a44cd14624f8178b9f48b7cc7 upstream.

This patch fixes the following sparse warning :
drivers/staging/serqt_usb2/serqt_usb2.c:727:40: warning: restricted __le16 degrades to integer

Signed-off-by: Himangi Saraogi <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
9 years agortlwifi: rtl8192se: Fix too long disable of IRQs
Larry Finger [Tue, 4 Mar 2014 22:53:51 +0000 (16:53 -0600)]
rtlwifi: rtl8192se: Fix too long disable of IRQs

commit 2610decdd0b3808ba20471a999835cfee5275f98 upstream.

In commit f78bccd79ba3cd9d9664981b501d57bdb81ab8a4 entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8192se.

Signed-off-by: Larry Finger <>
Signed-off-by: John W. Linville <>
[bwh: Backported to 3.2:
 - Adjust context
 - Drop change to an error path that we don't have]
Signed-off-by: Ben Hutchings <>
9 years agoblktrace: fix accounting of partially completed requests
Roman Pen [Tue, 4 Mar 2014 14:13:10 +0000 (23:13 +0900)]
blktrace: fix accounting of partially completed requests

commit af5040da01ef980670b3741b3e10733ee3e33566 upstream.

trace_block_rq_complete does not take into account that request can
be partially completed, so we can get the following incorrect output
of blkparser:

  C   R 232 + 240 [0]
  C   R 240 + 232 [0]
  C   R 248 + 224 [0]
  C   R 256 + 216 [0]

but should be:

  C   R 232 + 8 [0]
  C   R 240 + 8 [0]
  C   R 248 + 8 [0]
  C   R 256 + 8 [0]

Also, the whole output summary statistics of completed requests and
final throughput will be incorrect.

This patch takes into account real completion size of the request and
fixes wrong completion accounting.

Signed-off-by: Roman Pen <>
CC: Steven Rostedt <>
CC: Frederic Weisbecker <>
CC: Ingo Molnar <>
Signed-off-by: Jens Axboe <>
[bwh: Backported to 3.2: drop change in blk-mq.c]
Signed-off-by: Ben Hutchings <>
9 years agousb: gadget: atmel_usba: fix crashed during stopping when DEBUG is enabled
Gregory CLEMENT [Mon, 3 Mar 2014 16:48:34 +0000 (17:48 +0100)]
usb: gadget: atmel_usba: fix crashed during stopping when DEBUG is enabled

commit d8eb6c653ef6b323d630de3c5685478469e248bc upstream.

commit 511f3c5 (usb: gadget: udc-core: fix a regression during gadget driver
unbinding) introduced a crash when DEBUG is enabled.

The debug trace in the atmel_usba_stop function made the assumption that the
driver pointer passed in parameter was not NULL, but since the commit above,
such assumption was no longer always true.

This commit now uses the driver pointer stored in udc which fixes this

[ : improved commit log a bit ]

Acked-by: Alexandre Belloni <>
Signed-off-by: Gregory CLEMENT <>
Signed-off-by: Felipe Balbi <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
9 years agouvcvideo: Do not use usb_set_interface on bulk EP
Oleksij Rempel [Sun, 16 Feb 2014 09:59:32 +0000 (06:59 -0300)]
uvcvideo: Do not use usb_set_interface on bulk EP

commit b1e43f232698274871e1358c276d7b0242a7d607 upstream.

The UVC specification uses alternate setting selection to notify devices
of stream start/stop. This breaks when using bulk-based devices, as the
video streaming interface has a single alternate setting in that case,
making video stream start and video stream stop events to appear
identical to the device. Bulk-based devices are thus not well supported
by UVC.

The webcam built in the Asus Zenbook UX302LA ignores the set interface
request and will keep the video stream enabled when the driver tries to
stop it. If USB autosuspend is enabled the device will then be suspended
and will crash, requiring a cold reboot.

USB trace capture showed that Windows sends a CLEAR_FEATURE(HALT)
request to the bulk endpoint when stopping the stream instead of
selecting alternate setting 0. The camera then behaves correctly, and
thus seems to require that behaviour.

Replace selection of alternate setting 0 with clearing of the endpoint
halt feature at video stream stop for bulk-based devices. Let's refrain
from blaming Microsoft this time, as it's not clear whether this
Windows-specific but USB-compliant behaviour was specifically developed
to handle bulkd-based UVC devices, or if the camera just took advantage
of it.

Signed-off-by: Oleksij Rempel <>
Signed-off-by: Laurent Pinchart <>
Signed-off-by: Mauro Carvalho Chehab <>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <>
9 years agotty: Set correct tty name in 'active' sysfs attribute
Hannes Reinecke [Thu, 27 Feb 2014 11:30:51 +0000 (12:30 +0100)]
tty: Set correct tty name in 'active' sysfs attribute

commit 723abd87f6e536f1353c8f64f621520bc29523a3 upstream.

The 'active' sysfs attribute should refer to the currently active tty
devices the console is running on, not the currently active console. The
console structure doesn't refer to any device in sysfs, only the tty the
console is running on has. So we need to print out the tty names in
'active', not the console names.

There is one special-case, which is tty0. If the console is directed to
it, we want 'tty0' to show up in the file, so user-space knows that the
messages get forwarded to the active VT. The ->device() callback would
resolve tty0, though. Hence, treat it special and don't call into the VT
layer to resolve it (plymouth is known to depend on it).

Cc: Lennart Poettering <>
Cc: Kay Sievers <>
Cc: Greg Kroah-Hartman <>
Cc: Jiri Slaby <>
Signed-off-by: Werner Fink <>
Signed-off-by: Hannes Reinecke <>
Signed-off-by: David Herrmann <>
Signed-off-by: Greg Kroah-Hartman <>
[bwh: Backported to 3.2: no TTY_DRIVER_UNNUMBERED_NODE case in tty_line_name()]
Signed-off-by: Ben Hutchings <>
9 years agomedia: gspca: sn9c20x: add ID for Genius Look 1320 V2
Wolfram Sang [Sat, 1 Feb 2014 18:26:00 +0000 (15:26 -0300)]
media: gspca: sn9c20x: add ID for Genius Look 1320 V2

commit 61f0319193c44adbbada920162d880b1fdb3aeb3 upstream.

Signed-off-by: Wolfram Sang <>
Signed-off-by: Hans de Goede <>
Signed-off-by: Mauro Carvalho Chehab <>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <>
9 years agousb: dwc3: fix wrong bit mask in dwc3_event_devt
Huang Rui [Tue, 7 Jan 2014 09:45:50 +0000 (17:45 +0800)]
usb: dwc3: fix wrong bit mask in dwc3_event_devt

commit 06f9b6e59661cee510b04513b13ea7927727d758 upstream.

Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.

Because of that, what used to be 8 bits long, has become 9 bits long.

Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.

So in dwc3_event_devt, the bit mask should be:
event_info [24:16] 9 bits
reserved31_25 [31:25] 7 bits

This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.

[ : improve commit log a bit ]

Signed-off-by: Huang Rui <>
Signed-off-by: Felipe Balbi <>
Signed-off-by: Ben Hutchings <>
9 years agohvc: ensure hvc_init is only ever called once in hvc_console.c
Paul Gortmaker [Tue, 14 Jan 2014 21:03:37 +0000 (16:03 -0500)]
hvc: ensure hvc_init is only ever called once in hvc_console.c

commit f76a1cbed18c86e2d192455f0daebb48458965f3 upstream.

Commit 3e6c6f630a5282df8f3393a59f10eb9c56536d23 ("Delay creation of
khcvd thread") moved the call of hvc_init from being a device_initcall
into hvc_alloc, and used a non-null hvc_driver as indication of whether
hvc_init had already been called.

The problem with this is that hvc_driver is only assigned a value
at the bottom of hvc_init, and so there is a window where multiple
hvc_alloc calls can be in progress at the same time and hence try
and call hvc_init multiple times.  Previously the use of device_init
guaranteed that hvc_init was only called once.

This manifests itself as sporadic instances of two hvc_init calls
racing each other, and with the loser of the race getting -EBUSY
from tty_register_driver() and hence that virtual console fails:

    Couldn't register hvc console driver
    virtio-ports vport0p1: error -16 allocating hvc for port

Here we add an atomic_t to guarantee we'll never run hvc_init twice.

Cc: Rusty Russell <>
Cc: Greg Kroah-Hartman <>
Fixes: 3e6c6f630a52 ("Delay creation of khcvd thread")
Reported-by: Jim Somerville <>
Tested-by: Jim Somerville <>
Signed-off-by: Paul Gortmaker <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
9 years agotgafb: fix data copying
Mikulas Patocka [Thu, 23 Jan 2014 19:43:10 +0000 (14:43 -0500)]
tgafb: fix data copying

commit 6b0df6827bb6fcacb158dff29ad0a62d6418b534 upstream.

The functions for data copying copyarea_foreward_8bpp and
copyarea_backward_8bpp are buggy, they produce screen corruption.

This patch fixes the functions and moves the logic to one function
"copyarea_8bpp". For simplicity, the function only handles copying that
is aligned on 8 pixes. If we copy an unaligned area, generic function
cfb_copyarea is used.

Signed-off-by: Mikulas Patocka <>
Signed-off-by: Tomi Valkeinen <>
Signed-off-by: Ben Hutchings <>
9 years agomach64: fix cursor when character width is not a multiple of 8 pixels
Mikulas Patocka [Thu, 23 Jan 2014 19:41:59 +0000 (14:41 -0500)]
mach64: fix cursor when character width is not a multiple of 8 pixels

commit 43751a1b8ee2e70ce392bf31ef3133da324e68b3 upstream.

This patch fixes the hardware cursor on mach64 when font width is not a
multiple of 8 pixels.

If you load such a font, the cursor is expanded to the next 8-byte
boundary and a part of the next character after the cursor is not
For example, when you load a font with 12-pixel width, the cursor width
is 16 pixels and when the cursor is displayed, 4 pixels of the next
character are not visible.

The reason is this: atyfb_cursor is called with proper parameters to
load an image that is 12-pixel wide. However, the number is aligned on
the next 8-pixel boundary on the line
"unsigned int width = (cursor->image.width + 7) >> 3;" and the whole
function acts as it is was loading a 16-pixel image.

This patch fixes it so that the value written to the framebuffer is
padded with 0xaaaa (the transparent pattern) when the image size it not
a multiple of 8 pixels. The transparent pattern causes that the cursor
will not interfere with the next character.

Signed-off-by: Mikulas Patocka <>
Signed-off-by: Tomi Valkeinen <>
Signed-off-by: Ben Hutchings <>
9 years agomach64: use unaligned access
Mikulas Patocka [Thu, 23 Jan 2014 19:41:09 +0000 (14:41 -0500)]
mach64: use unaligned access

commit c29dd8696dc5dbd50b3ac441b8a26751277ba520 upstream.

This patch fixes mach64 to use unaligned access to the font bitmap.

This fixes unaligned access warning on sparc64 when 14x8 font is loaded.

On x86(64), unaligned access is handled in hardware, so both functions
le32_to_cpup and get_unaligned_le32 perform the same operation.

On RISC machines, unaligned access is not handled in hardware, so we
better use get_unaligned_le32 to avoid the unaligned trap and warning.

Signed-off-by: Mikulas Patocka <>
Signed-off-by: Tomi Valkeinen <>
Signed-off-by: Ben Hutchings <>
9 years agoframebuffer: fix cfb_copyarea
Mikulas Patocka [Thu, 23 Jan 2014 19:39:29 +0000 (14:39 -0500)]
framebuffer: fix cfb_copyarea

commit 00a9d699bc85052d2d3ed56251cd928024ce06a3 upstream.

The function cfb_copyarea is buggy when the copy operation is not aligned on
long boundary (4 bytes on 32-bit machines, 8 bytes on 64-bit machines).

How to reproduce:
- use x86-64 machine
- use a framebuffer driver without acceleration (for example uvesafb)
- set the framebuffer to 8-bit depth
(for example fbset -a 1024x768-60 -depth 8)
- load a font with character width that is not a multiple of 8 pixels
note: the console-tools package cannot load a font that has
width different from 8 pixels. You need to install the packages
"kbd" and "console-terminus" and use the program "setfont" to
set font width (for example: setfont Uni2-Terminus20x10)
- move some text left and right on the bash command line and you get a
screen corruption

To expose more bugs, put this line to the end of uvesafb_init_info:
- Now framebuffer console will use cfb_copyarea for console scrolling.
You get a screen corruption when console is scrolled.

This patch is a rewrite of cfb_copyarea. It fixes the bugs, with this
patch, console scrolling in 8-bit depth with a font width that is not a
multiple of 8 pixels works fine.

The cfb_copyarea code was very buggy and it looks like it was written
and never tried with non-8-pixel font.

Signed-off-by: Mikulas Patocka <>
Signed-off-by: Tomi Valkeinen <>
Signed-off-by: Ben Hutchings <>
9 years agomatroxfb: restore the registers M_ACCESS and M_PITCH
Mikulas Patocka [Thu, 23 Jan 2014 19:39:04 +0000 (14:39 -0500)]
matroxfb: restore the registers M_ACCESS and M_PITCH

commit a772d4736641ec1b421ad965e13457c17379fc86 upstream.

When X11 is running and the user switches back to console, the card
modifies the content of registers M_MACCESS and M_PITCH in periodic

This patch fixes it by restoring the content of these registers before
issuing any accelerator command.

Signed-off-by: Mikulas Patocka <>
Signed-off-by: Tomi Valkeinen <>
Signed-off-by: Ben Hutchings <>
9 years agoARM: 7954/1: mm: remove remaining domain support from ARMv6
Will Deacon [Fri, 7 Feb 2014 18:12:27 +0000 (19:12 +0100)]
ARM: 7954/1: mm: remove remaining domain support from ARMv6

commit b6ccb9803e90c16b212cf4ed62913a7591e79a39 upstream.

CPU_32v6 currently selects CPU_USE_DOMAINS if CPU_V6 and MMU. This is
because ARM 1136 r0pX CPUs lack the v6k extensions, and therefore do
not have hardware thread registers. The lack of these registers requires
the kernel to update the vectors page at each context switch in order to
write a new TLS pointer. This write must be done via the userspace
mapping, since aliasing caches can lead to expensive flushing when using
kmap. Finally, this requires the vectors page to be mapped r/w for
kernel and r/o for user, which has implications for things like put_user
which must trigger CoW appropriately when targetting user pages.

The upshot of all this is that a v6/v7 kernel makes use of domains to
segregate kernel and user memory accesses. This has the nasty
side-effect of making device mappings executable, which has been
observed to cause subtle bugs on recent cores (e.g. Cortex-A15
performing a speculative instruction fetch from the GIC and acking an
interrupt in the process).

This patch solves this problem by removing the remaining domain support
from ARMv6. A new memory type is added specifically for the vectors page
which allows that page (and only that page) to be mapped as user r/o,
kernel r/w. All other user r/o pages are mapped also as kernel r/o.
Patch co-developed with Russell King.

Signed-off-by: Will Deacon <>
Signed-off-by: Russell King <>
[bwh: Backported to 3.2:
 - Adjust filename, context
 - Drop condition on CONFIG_ARM_LPAE]
Signed-off-by: Ben Hutchings <>
9 years agoARM: mm: introduce present, faulting entries for PAGE_NONE
Will Deacon [Sat, 1 Sep 2012 04:22:12 +0000 (05:22 +0100)]
ARM: mm: introduce present, faulting entries for PAGE_NONE

commit 26ffd0d43b186b0d5186354da8714a1c2d360df0 upstream.

PROT_NONE mappings apply the page protection attributes defined by _P000
which translate to PAGE_NONE for ARM. These attributes specify an XN,
RDONLY pte that is inaccessible to userspace. However, on kernels
configured without support for domains, such a pte *is* accessible to
the kernel and can be read via get_user, allowing tasks to read
PROT_NONE pages via syscalls such as read/write over a pipe.

This patch introduces a new software pte flag, L_PTE_NONE, that is set
to identify faulting, present entries.

Signed-off-by: Will Deacon <>
[bwh: Backported to 3.2 as dependency of commit b6ccb9803e90
 ('ARM: 7954/1: mm: remove remaining domain support from ARMv6'):
 - Drop 3-level changes
 - Adjust filename, context]
Signed-off-by: Ben Hutchings <>