8 years agoxhci: fix reporting of 0-sized URBs in control endpoint
Aleksander Morgado [Fri, 6 Mar 2015 15:14:21 +0000 (17:14 +0200)]
xhci: fix reporting of 0-sized URBs in control endpoint

commit 45ba2154d12fc43b70312198ec47085f10be801a upstream.

When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.

The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.

This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.

This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control

Signed-off-by: Aleksander Morgado <>
Signed-off-by: Mathias Nyman <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
8 years agox86/asm/entry/64: Remove a bogus 'ret_from_fork' optimization
Andy Lutomirski [Thu, 5 Mar 2015 00:09:44 +0000 (01:09 +0100)]
x86/asm/entry/64: Remove a bogus 'ret_from_fork' optimization

commit 956421fbb74c3a6261903f3836c0740187cf038b upstream.

'ret_from_fork' checks TIF_IA32 to determine whether 'pt_regs' and
the related state make sense for 'ret_from_sys_call'.  This is
entirely the wrong check.  TS_COMPAT would make a little more
sense, but there's really no point in keeping this optimization
at all.

This fixes a return to the wrong user CS if we came from int
0x80 in a 64-bit task.

Signed-off-by: Andy Lutomirski <>
Cc: Borislav Petkov <>
Cc: Denys Vlasenko <>
Cc: H. Peter Anvin <>
Cc: Linus Torvalds <>
Cc: Oleg Nesterov <>
Cc: Thomas Gleixner <>
[ Backported from tip:x86/asm. ]
Signed-off-by: Ingo Molnar <>
Signed-off-by: Ben Hutchings <>
8 years agoASoC: omap-pcm: Correct dma mask
Peter Ujfalusi [Tue, 3 Mar 2015 11:38:14 +0000 (13:38 +0200)]
ASoC: omap-pcm: Correct dma mask

commit d51199a83a2cf82a291d19ee852c44caa511427d upstream.

DMA_BIT_MASK of 64 is not valid dma address mask for OMAPs, it should be
set to 32.
The 64 was introduced by commit (in 2009):
a152ff24b978 ASoC: OMAP: Make DMA 64 aligned

But the dma_mask and coherent_dma_mask can not be used to specify alignment.

Fixes: a152ff24b978 (ASoC: OMAP: Make DMA 64 aligned)
Reported-by: Grygorii Strashko <>
Signed-off-by: Peter Ujfalusi <>
Signed-off-by: Mark Brown <>
[bwh: Backported to 3.2: not using dma_coerce_mask_and_coherent()]
Signed-off-by: Ben Hutchings <>
8 years agoACPI / video: Load the module even if ACPI is disabled
Chris Wilson [Sun, 1 Mar 2015 10:41:37 +0000 (10:41 +0000)]
ACPI / video: Load the module even if ACPI is disabled

commit 6e17cb12881ba8d5e456b89f072dc6b70048af36 upstream.

i915.ko depends upon the acpi/video.ko module and so refuses to load if
ACPI is disabled at runtime if for example the BIOS is broken beyond
repair. acpi/video provides an optional service for i915.ko and so we
should just allow the modules to load, but do no nothing in order to let
the machines boot correctly.

Reported-by: Bill Augur <>
Signed-off-by: Chris Wilson <>
Cc: Daniel Vetter <>
Cc: Jani Nikula <>
Acked-by: Aaron Lu <>
[ rjw: Fixed up the new comment in acpi_video_init() ]
Signed-off-by: Rafael J. Wysocki <>
Signed-off-by: Ben Hutchings <>
8 years agodrm/radeon: fix DRM_IOCTL_RADEON_CS oops
Tommi Rantala [Mon, 2 Mar 2015 19:36:07 +0000 (21:36 +0200)]
drm/radeon: fix DRM_IOCTL_RADEON_CS oops

commit a28b2a47edcd0cb7c051b445f71a426000394606 upstream.

Passing zeroed drm_radeon_cs struct to DRM_IOCTL_RADEON_CS produces the
following oops.

Fix by always calling INIT_LIST_HEAD() to avoid the crash in list_sort().


 #include <stdint.h>
 #include <fcntl.h>
 #include <unistd.h>
 #include <sys/ioctl.h>
 #include <drm/radeon_drm.h>

 static const struct drm_radeon_cs cs;

 int main(int argc, char **argv)
         return ioctl(open(argv[1], O_RDWR), DRM_IOCTL_RADEON_CS, &cs);


[ttrantal@test2 ~]$ ./main /dev/dri/card0
[   46.904650] BUG: unable to handle kernel NULL pointer dereference at           (null)
[   46.905022] IP: [<ffffffff814d6df2>] list_sort+0x42/0x240
[   46.905022] PGD 68f29067 PUD 688b5067 PMD 0
[   46.905022] Oops: 0002 [#1] SMP
[   46.905022] CPU: 0 PID: 2413 Comm: main Not tainted 4.0.0-rc1+ #58
[   46.905022] Hardware name: Hewlett-Packard HP Compaq dc5750 Small Form Factor/0A64h, BIOS 786E3 v02.10 01/25/2007
[   46.905022] task: ffff880058e2bcc0 ti: ffff880058e64000 task.ti: ffff880058e64000
[   46.905022] RIP: 0010:[<ffffffff814d6df2>]  [<ffffffff814d6df2>] list_sort+0x42/0x240
[   46.905022] RSP: 0018:ffff880058e67998  EFLAGS: 00010246
[   46.905022] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[   46.905022] RDX: ffffffff81644410 RSI: ffff880058e67b40 RDI: ffff880058e67a58
[   46.905022] RBP: ffff880058e67a88 R08: 0000000000000000 R09: 0000000000000000
[   46.905022] R10: ffff880058e2bcc0 R11: ffffffff828e6ca0 R12: ffffffff81644410
[   46.905022] R13: ffff8800694b8018 R14: 0000000000000000 R15: ffff880058e679b0
[   46.905022] FS:  00007fdc65a65700(0000) GS:ffff88006d600000(0000) knlGS:0000000000000000
[   46.905022] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   46.905022] CR2: 0000000000000000 CR3: 0000000058dd9000 CR4: 00000000000006f0
[   46.905022] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   46.905022] DR3: 0000000000000000 DR6: 00000000ffff4ff0 DR7: 0000000000000400
[   46.905022] Stack:
[   46.905022]  ffff880058e67b40 ffff880058e2bcc0 ffff880058e67a78 0000000000000000
[   46.905022]  0000000000000000 0000000000000000 0000000000000000 0000000000000000
[   46.905022]  0000000000000000 0000000000000000 0000000000000000 0000000000000000
[   46.905022] Call Trace:
[   46.905022]  [<ffffffff81644a65>] radeon_cs_parser_fini+0x195/0x220
[   46.905022]  [<ffffffff81645069>] radeon_cs_ioctl+0xa9/0x960
[   46.905022]  [<ffffffff815e1f7c>] drm_ioctl+0x19c/0x640
[   46.905022]  [<ffffffff810f8fdd>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[   46.905022]  [<ffffffff810f90ad>] ? trace_hardirqs_on+0xd/0x10
[   46.905022]  [<ffffffff8160c066>] radeon_drm_ioctl+0x46/0x80
[   46.905022]  [<ffffffff81211868>] do_vfs_ioctl+0x318/0x570
[   46.905022]  [<ffffffff81462ef6>] ? selinux_file_ioctl+0x56/0x110
[   46.905022]  [<ffffffff81211b41>] SyS_ioctl+0x81/0xa0
[   46.905022]  [<ffffffff81dc6312>] system_call_fastpath+0x12/0x17
[   46.905022] Code: 48 89 b5 10 ff ff ff 0f 84 03 01 00 00 4c 8d bd 28 ff ff
ff 31 c0 48 89 fb b9 15 00 00 00 49 89 d4 4c 89 ff f3 48 ab 48 8b 46 08 <48> c7
00 00 00 00 00 48 8b 0e 48 85 c9 0f 84 7d 00 00 00 c7 85
[   46.905022] RIP  [<ffffffff814d6df2>] list_sort+0x42/0x240
[   46.905022]  RSP <ffff880058e67998>
[   46.905022] CR2: 0000000000000000
[   47.149253] ---[ end trace 09576b4e8b2c20b8 ]---

Reviewed-by: Christian König <>
Signed-off-by: Tommi Rantala <>
Signed-off-by: Alex Deucher <>
Signed-off-by: Ben Hutchings <>
8 years agodrm/radeon: do a posting read in evergreen_set_irq
Alex Deucher [Tue, 3 Mar 2015 01:42:53 +0000 (20:42 -0500)]
drm/radeon: do a posting read in evergreen_set_irq

commit c320bb5f6dc0cb88a811cbaf839303e0a3916a92 upstream.

To make sure the writes go through the pci bridge.


Signed-off-by: Alex Deucher <>
Signed-off-by: Ben Hutchings <>
8 years agodrm/radeon: do a posting read in r600_set_irq
Alex Deucher [Tue, 3 Mar 2015 01:41:31 +0000 (20:41 -0500)]
drm/radeon: do a posting read in r600_set_irq

commit 9d1393f23d5656cdd5f368efd60694d4aeed81d3 upstream.

To make sure the writes go through the pci bridge.


Signed-off-by: Alex Deucher <>
Signed-off-by: Ben Hutchings <>
8 years agodrm/radeon: do a posting read in rs600_set_irq
Alex Deucher [Tue, 3 Mar 2015 01:39:56 +0000 (20:39 -0500)]
drm/radeon: do a posting read in rs600_set_irq

commit 54acf107e4e66d1f4a697e08a7f60dba9fcf07c3 upstream.

To make sure the writes go through the pci bridge.


Signed-off-by: Alex Deucher <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agodrm/radeon: do a posting read in r100_set_irq
Alex Deucher [Tue, 3 Mar 2015 01:36:26 +0000 (20:36 -0500)]
drm/radeon: do a posting read in r100_set_irq

commit f957063fee6392bb9365370db6db74dc0b2dce0a upstream.

To make sure the writes go through the pci bridge.


Signed-off-by: Alex Deucher <>
Signed-off-by: Ben Hutchings <>
8 years agoeCryptfs: don't pass fs-specific ioctl commands through
Tyler Hicks [Wed, 25 Feb 2015 01:28:10 +0000 (19:28 -0600)]
eCryptfs: don't pass fs-specific ioctl commands through

commit 6d65261a09adaa374c05de807f73a144d783669e upstream.

eCryptfs can't be aware of what to expect when after passing an
arbitrary ioctl command through to the lower filesystem. The ioctl
command may trigger an action in the lower filesystem that is
incompatible with eCryptfs.

One specific example is when one attempts to use the Btrfs clone
ioctl command when the source file is in the Btrfs filesystem that
eCryptfs is mounted on top of and the destination fd is from a new file
created in the eCryptfs mount. The ioctl syscall incorrectly returns
success because the command is passed down to Btrfs which thinks that it
was able to do the clone operation. However, the result is an empty
eCryptfs file.

This patch allows the trim, {g,s}etflags, and {g,s}etversion ioctl
commands through and then copies up the inode metadata from the lower
inode to the eCryptfs inode to catch any changes made to the lower
inode's metadata. Those five ioctl commands are mostly common across all
filesystems but the whitelist may need to be further pruned in the

Signed-off-by: Tyler Hicks <>
Cc: Rocko <>
Cc: Colin Ian King <>
[bwh: Backported to 3.2:
 - Adjust context
 - We don't have file_inode() so open-code the inode lookup]
Signed-off-by: Ben Hutchings <>
8 years agousb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
Max Mansfield [Tue, 3 Mar 2015 01:38:02 +0000 (18:38 -0700)]
usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards

commit c7d373c3f0da2b2b78c4b1ce5ae41485b3ef848c upstream.

This patch integrates Cyber Cortex AV boards with the existing
ftdi_jtag_quirk in order to use serial port 0 with JTAG which is
required by the manufacturers' software.

Steps: 2

1. Defined the device PID

2. Added a macro declaration to the ids array, in order to enable the
jtag quirk for the device.

Signed-off-by: Max Mansfield <>
Signed-off-by: Johan Hovold <>
Signed-off-by: Ben Hutchings <>
8 years agoNFSv4: Don't call put_rpccred() under the rcu_read_lock()
Trond Myklebust [Thu, 26 Feb 2015 17:54:46 +0000 (12:54 -0500)]
NFSv4: Don't call put_rpccred() under the rcu_read_lock()

commit 7c0af9ffb7bb4e5355470fa60b3eb711ddf226fa upstream.

put_rpccred() can sleep.

Fixes: 8f649c3762547 ("NFSv4: Fix the locking in nfs_inode_reclaim_delegation()")
Signed-off-by: Trond Myklebust <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agonilfs2: fix potential memory overrun on inode
Ryusuke Konishi [Fri, 27 Feb 2015 23:51:56 +0000 (15:51 -0800)]
nilfs2: fix potential memory overrun on inode

commit 957ed60b53b519064a54988c4e31e0087e47d091 upstream.

Each inode of nilfs2 stores a root node of a b-tree, and it turned out to
have a memory overrun issue:

Each b-tree node of nilfs2 stores a set of key-value pairs and the number
of them (in "bn_nchildren" member of nilfs_btree_node struct), as well as
a few other "bn_*" members.

Since the value of "bn_nchildren" is used for operations on the key-values
within the b-tree node, it can cause memory access overrun if a large
number is incorrectly set to "bn_nchildren".

For instance, nilfs_btree_node_lookup() function determines the range of
binary search with it, and too large "bn_nchildren" leads
nilfs_btree_node_get_key() in that function to overrun.

As for intermediate b-tree nodes, this is prevented by a sanity check
performed when each node is read from a drive, however, no sanity check
has been done for root nodes stored in inodes.

This patch fixes the issue by adding missing sanity check against b-tree
root nodes so that it's called when on-memory inodes are read from ifile,
inode metadata file.

Signed-off-by: Ryusuke Konishi <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
8 years agoUSB: serial: cp210x: Adding Seletek device id's
Michiel vd Garde [Fri, 27 Feb 2015 01:08:29 +0000 (02:08 +0100)]
USB: serial: cp210x: Adding Seletek device id's

commit 675af70856d7cc026be8b6ea7a8b9db10b8b38a1 upstream.

These device ID's are not associated with the cp210x module currently,
but should be. This patch allows the devices to operate upon connecting
them to the usb bus as intended.

Signed-off-by: Michiel van de Garde <>
Signed-off-by: Johan Hovold <>
Signed-off-by: Ben Hutchings <>
8 years agomac80211: Send EAPOL frames at lowest rate
Jouni Malinen [Thu, 26 Feb 2015 13:50:50 +0000 (15:50 +0200)]
mac80211: Send EAPOL frames at lowest rate

commit 9c1c98a3bb7b7593b60264b9a07e001e68b46697 upstream.

The current minstrel_ht rate control behavior is somewhat optimistic in
trying to find optimum TX rate. While this is usually fine for normal
Data frames, there are cases where a more conservative set of retry
parameters would be beneficial to make the connection more robust.

EAPOL frames are critical to the authentication and especially the
EAPOL-Key message 4/4 (the last message in the 4-way handshake) is
important to get through to the AP. If that message is lost, the only
recovery mechanism in many cases is to reassociate with the AP and start
from scratch. This can often be avoided by trying to send the frame with
more conservative rate and/or with more link layer retries.

In most cases, minstrel_ht is currently using the initial EAPOL-Key
frames for probing higher rates and this results in only five link layer
transmission attempts (one at high(ish) MCS and four at MCS0). While
this works with most APs, it looks like there are some deployed APs that
may have issues with the EAPOL frames using HT MCS immediately after
association. Similarly, there may be issues in cases where the signal
strength or radio environment is not good enough to be able to get
frames through even at couple of MCS 0 tries.

The best approach for this would likely to be to reduce the TX rate for
the last rate (3rd rate parameter in the set) to a low basic rate (say,
6 Mbps on 5 GHz and 2 or 5.5 Mbps on 2.4 GHz), but doing that cleanly
requires some more effort. For now, we can start with a simple one-liner
that forces the minimum rate to be used for EAPOL frames similarly how
the TX rate is selected for the IEEE 802.11 Management frames. This does
result in a small extra latency added to the cases where the AP would be
able to receive the higher rate, but taken into account how small number
of EAPOL frames are used, this is likely to be insignificant. A future
optimization in the minstrel_ht design can also allow this patch to be
reverted to get back to the more optimized initial TX rate.

It should also be noted that many drivers that do not use minstrel as
the rate control algorithm are already doing similar workarounds by
forcing the lowest TX rate to be used for EAPOL frames.

Reported-by: Linus Torvalds <>
Tested-by: Linus Torvalds <>
Signed-off-by: Jouni Malinen <>
Signed-off-by: Johannes Berg <>
[bwh: Backported to 3.2: adjust the controlling if-statement to make
 this work]
Signed-off-by: Ben Hutchings <>
8 years agoUSB: serial: fix tty-device error handling at probe
Johan Hovold [Wed, 18 Feb 2015 03:34:51 +0000 (10:34 +0700)]
USB: serial: fix tty-device error handling at probe

commit ca4383a3947a83286bc9b9c598a1f55e867871d7 upstream.

Add missing error handling when registering the tty device at port
probe. This avoids trying to remove an uninitialised character device
when the port device is removed.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Takashi Iwai <>
Signed-off-by: Johan Hovold <>
Acked-by: Greg Kroah-Hartman <>
[bwh: Backported to 3.2:
 - Adjust context
 - No need to clean up autopm]
Signed-off-by: Ben Hutchings <>
8 years agoUSB: serial: fix potential use-after-free after failed probe
Johan Hovold [Wed, 18 Feb 2015 03:34:50 +0000 (10:34 +0700)]
USB: serial: fix potential use-after-free after failed probe

commit 07fdfc5e9f1c966be8722e8fa927e5ea140df5ce upstream.

Fix return value in probe error path, which could end up returning
success (0) on errors. This could in turn lead to use-after-free or
double free (e.g. in port_remove) when the port device is removed.

Fixes: c706ebdfc895 ("USB: usb-serial: call port_probe and port_remove
at the right times")
Signed-off-by: Johan Hovold <>
Acked-by: Greg Kroah-Hartman <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agoUSB: ftdi_sio: add PIDs for Actisense USB devices
Mark Glover [Fri, 13 Feb 2015 09:04:39 +0000 (09:04 +0000)]
USB: ftdi_sio: add PIDs for Actisense USB devices

commit f6950344d3cf4a1e231b5828b50c4ac168db3886 upstream.

These product identifiers (PID) all deal with marine NMEA format data
used on motor boats and yachts. We supply the programmed devices to
Chetco, for use inside their equipment. The PIDs are a direct copy of
our Windows device drivers (FTDI drivers with altered PIDs).

Signed-off-by: Mark Glover <>
[johan: edit commit message slightly ]
Signed-off-by: Johan Hovold <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agoUSB: usbfs: don't leak kernel data in siginfo
Alan Stern [Fri, 13 Feb 2015 15:54:53 +0000 (10:54 -0500)]
USB: usbfs: don't leak kernel data in siginfo

commit f0c2b68198589249afd2b1f2c4e8de8c03e19c16 upstream.

When a signal is delivered, the information in the siginfo structure
is copied to userspace.  Good security practice dicatates that the
unused fields in this structure should be initialized to 0 so that
random kernel stack data isn't exposed to the user.  This patch adds
such an initialization to the two places where usbfs raises signals.

Signed-off-by: Alan Stern <>
Reported-by: Dave Mielke <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
8 years agoxhci: Allocate correct amount of scratchpad buffers
Mathias Nyman [Tue, 24 Feb 2015 16:27:01 +0000 (18:27 +0200)]
xhci: Allocate correct amount of scratchpad buffers

commit 6596a926b0b6c80b730a1dd2fa91908e0a539c37 upstream.

Include the high order bit fields for Max scratchpad buffers when
calculating how many scratchpad buffers are needed.

I'm suprised this hasn't caused more issues, we never allocated more than
32 buffers even if xhci needed more. Either we got lucky and xhci never
really used past that area, or then we got enough zeroed dma memory anyway.

Should be backported as far back as possible

Reported-by: Tim Chen <>
Tested-by: Tim Chen <>
Signed-off-by: Mathias Nyman <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
8 years agonet: compat: Ignore MSG_CMSG_COMPAT in compat_sys_{send, recv}msg
Catalin Marinas [Mon, 23 Feb 2015 18:12:56 +0000 (18:12 +0000)]
net: compat: Ignore MSG_CMSG_COMPAT in compat_sys_{send, recv}msg

commit d720d8cec563ce4e4fa44a613d4f2dcb1caf2998 upstream.

With commit a7526eb5d06b (net: Unbreak compat_sys_{send,recv}msg), the
MSG_CMSG_COMPAT flag is blocked at the compat syscall entry points,
changing the kernel compat behaviour from the one before the commit it
was trying to fix (1be374a0518a, net: Block MSG_CMSG_COMPAT in
send(m)msg and recv(m)msg).

On 32-bit kernels (!CONFIG_COMPAT), MSG_CMSG_COMPAT is 0 and the native
32-bit sys_sendmsg() allows flag 0x80000000 to be set (it is ignored by
the kernel). However, on a 64-bit kernel, the compat ABI is different
with commit a7526eb5d06b.

This patch changes the compat_sys_{send,recv}msg behaviour to the one
prior to commit 1be374a0518a.

The problem was found running 32-bit LTP (sendmsg01) binary on an arm64
kernel. Arguably, LTP should not pass 0xffffffff as flags to sendmsg()
but the general rule is not to break user ABI (even when the user
behaviour is not entirely sane).

Fixes: a7526eb5d06b (net: Unbreak compat_sys_{send,recv}msg)
Cc: Andy Lutomirski <>
Cc: David S. Miller <>
Signed-off-by: Catalin Marinas <>
Signed-off-by: David S. Miller <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agoKVM: emulate: fix CMPXCHG8B on 32-bit hosts
Paolo Bonzini [Thu, 12 Feb 2015 16:04:47 +0000 (17:04 +0100)]
KVM: emulate: fix CMPXCHG8B on 32-bit hosts

commit 4ff6f8e61eb7f96d3ca535c6d240f863ccd6fb7d upstream.

This has been broken for a long time: it broke first in 2.6.35, then was
almost fixed in 2.6.36 but this one-liner slipped through the cracks.
The bug shows up as an infinite loop in Windows 7 (and newer) boot on
32-bit hosts without EPT.

Windows uses CMPXCHG8B to write to page tables, which causes a
page fault if running without EPT; the emulator is then called from
kvm_mmu_page_fault.  The loop then happens if the higher 4 bytes are
not 0; the common case for this is that the NX bit (bit 63) is 1.

Fixes: 6550e1f165f384f3a46b60a1be9aba4bc3c2adad
Fixes: 16518d5ada690643453eb0aef3cc7841d3623c2d
Reported-by: Erik Rull <>
Tested-by: Erik Rull <>
Signed-off-by: Paolo Bonzini <>
Signed-off-by: Ben Hutchings <>
8 years agoALSA: pcm: Don't leave PREPARED state after draining
Takashi Iwai [Thu, 18 Dec 2014 09:02:41 +0000 (10:02 +0100)]
ALSA: pcm: Don't leave PREPARED state after draining

commit 70372a7566b5e552dbe48abdac08c275081d8558 upstream.

When a PCM draining is performed to an empty stream that has been
already in PREPARED state, the current code just ignores and leaves as
it is, although the drain is supposed to set all such streams to SETUP
state.  This patch covers that overlooked case.

Signed-off-by: Takashi Iwai <>
Signed-off-by: Ben Hutchings <>
8 years agogpio: tps65912: fix wrong container_of arguments
Nicolas Saenz Julienne [Thu, 19 Feb 2015 01:52:25 +0000 (01:52 +0000)]
gpio: tps65912: fix wrong container_of arguments

commit 2f97c20e5f7c3582c7310f65a04465bfb0fd0e85 upstream.

The gpio_chip operations receive a pointer the gpio_chip struct which is
contained in the driver's private struct, yet the container_of call in those
functions point to the mfd struct defined in include/linux/mfd/tps65912.h.

Signed-off-by: Nicolas Saenz Julienne <>
Signed-off-by: Linus Walleij <>
Signed-off-by: Ben Hutchings <>
8 years agoxfs: ensure truncate forces zeroed blocks to disk
Dave Chinner [Mon, 23 Feb 2015 11:37:08 +0000 (22:37 +1100)]
xfs: ensure truncate forces zeroed blocks to disk

commit 5885ebda878b47c4b4602d4b0410cb4b282af024 upstream.

A new fsync vs power fail test in xfstests indicated that XFS can
have unreliable data consistency when doing extending truncates that
require block zeroing. The blocks beyond EOF get zeroed in memory,
but we never force those changes to disk before we run the
transaction that extends the file size and exposes those blocks to
userspace. This can result in the blocks not being correctly zeroed
after a crash.

Because in-memory behaviour is correct, tools like fsx don't pick up
any coherency problems - it's not until the filesystem is shutdown
or the system crashes after writing the truncate transaction to the
journal but before the zeroed data in the page cache is flushed that
the issue is exposed.

Fix this by also flushing the dirty data in memory region between
the old size and new size when we've found blocks that need zeroing
in the truncate process.

Reported-by: Liu Bo <>
Signed-off-by: Dave Chinner <>
Reviewed-by: Brian Foster <>
Signed-off-by: Dave Chinner <>
[bwh: Backported to 3.2: adjust filename, context]
Signed-off-by: Ben Hutchings <>
8 years agoautofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
Al Viro [Sun, 22 Feb 2015 03:19:57 +0000 (22:19 -0500)]
autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation

commit 0a280962dc6e117e0e4baa668453f753579265d9 upstream.

X-Coverup: just ask spender
Signed-off-by: Al Viro <>
Signed-off-by: Ben Hutchings <>
8 years agoautofs4: check dev ioctl size before allocating
Sasha Levin [Tue, 8 Apr 2014 23:04:11 +0000 (16:04 -0700)]
autofs4: check dev ioctl size before allocating

commit e53d77eb8bb616e903e34cc7a918401bee3b5149 upstream.

There wasn't any check of the size passed from userspace before trying
to allocate the memory required.

This meant that userspace might request more space than allowed,
triggering an OOM.

Signed-off-by: Sasha Levin <>
Signed-off-by: Ian Kent <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
8 years agodebugfs: leave freeing a symlink body until inode eviction
Al Viro [Sun, 22 Feb 2015 03:05:11 +0000 (22:05 -0500)]
debugfs: leave freeing a symlink body until inode eviction

commit 0db59e59299f0b67450c5db21f7f316c8fb04e84 upstream.

As it is, we have debugfs_remove() racing with symlink traversals.
Supply ->evict_inode() and do freeing there - inode will remain
pinned until we are done with the symlink body.

And rip the idiocy with checking if dentry is positive right after
we'd verified debugfs_positive(), which is a stronger check...

Signed-off-by: Al Viro <>
[bwh: Backported to 3.2:
 - Plumb in debugfs_super_operations, which we didn't previously define
 - Call truncate_inode_pages() instead of truncate_inode_pages_final()
 - Call end_writeback() instead of clear_inode()]
Signed-off-by: Ben Hutchings <>
8 years agoipv4: ip_check_defrag should correctly check return value of skb_copy_bits
Alexander Drozdov [Tue, 17 Feb 2015 10:33:46 +0000 (13:33 +0300)]
ipv4: ip_check_defrag should correctly check return value of skb_copy_bits

commit fba04a9e0c869498889b6445fd06cbe7da9bb834 upstream.

skb_copy_bits() returns zero on success and negative value on error,
so it is needed to invert the condition in ip_check_defrag().

Fixes: 1bf3751ec90c ("ipv4: ip_check_defrag must not modify skb before unsharing")
Signed-off-by: Alexander Drozdov <>
Acked-by: Eric Dumazet <>
Signed-off-by: David S. Miller <>
Signed-off-by: Ben Hutchings <>
8 years agokdb: fix incorrect counts in KDB summary command output
Jay Lan [Mon, 29 Sep 2014 22:36:57 +0000 (15:36 -0700)]
kdb: fix incorrect counts in KDB summary command output

commit 146755923262037fc4c54abc28c04b1103f3cc51 upstream.

The output of KDB 'summary' command should report MemTotal, MemFree
and Buffers output in kB. Current codes report in unit of pages.

A define of K(x) as
is defined in the code, but not used.

This patch would apply the define to convert the values to kB.
Please include me on Cc on replies. I do not subscribe to linux-kernel.

Signed-off-by: Jay Lan <>
Signed-off-by: Jason Wessel <>
Signed-off-by: Ben Hutchings <>
8 years agolibceph: fix double __remove_osd() problem
Ilya Dryomov [Tue, 17 Feb 2015 16:37:15 +0000 (19:37 +0300)]
libceph: fix double __remove_osd() problem

commit 7eb71e0351fbb1b242ae70abb7bb17107fe2f792 upstream.

It turns out it's possible to get __remove_osd() called twice on the
same OSD.  That doesn't sit well with rb_erase() - depending on the
shape of the tree we can get a NULL dereference, a soft lockup or
a random crash at some point in the future as we end up touching freed
memory.  One scenario that I was able to reproduce is as follows:

            <osd3 is idle, on the osd lru list>
<con reset - osd3>
                              <osdmap - osd3 down>
                                <takes map_sem>
                                  <takes request_mutex>
                                  <releases request_mutex>
                                <releases map_sem>
    <takes map_sem>
    <takes request_mutex>
        __remove_osd() <-- !!!

A case can be made that osd refcounting is imperfect and reworking it
would be a proper resolution, but for now Sage and I decided to fix
this by adding a safe guard around __remove_osd().


Cc: Sage Weil <>
Signed-off-by: Ilya Dryomov <>
Reviewed-by: Sage Weil <>
Reviewed-by: Alex Elder <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agox86, mm/ASLR: Fix stack randomization on 64-bit systems
Hector Marco-Gisbert [Sat, 14 Feb 2015 17:33:50 +0000 (09:33 -0800)]
x86, mm/ASLR: Fix stack randomization on 64-bit systems

commit 4e7c22d447bb6d7e37bfe39ff658486ae78e8d77 upstream.

The issue is that the stack for processes is not properly randomized on
64 bit architectures due to an integer overflow.

The affected function is randomize_stack_top() in file

  static unsigned long randomize_stack_top(unsigned long stack_top)
           unsigned int random_variable = 0;

           if ((current->flags & PF_RANDOMIZE) &&
                   !(current->personality & ADDR_NO_RANDOMIZE)) {
                   random_variable = get_random_int() & STACK_RND_MASK;
                   random_variable <<= PAGE_SHIFT;
           return PAGE_ALIGN(stack_top) + random_variable;
           return PAGE_ALIGN(stack_top) - random_variable;

Note that, it declares the "random_variable" variable as "unsigned int".
Since the result of the shifting operation between STACK_RND_MASK (which
is 0x3fffff on x86_64, 22 bits) and PAGE_SHIFT (which is 12 on x86_64):

  random_variable <<= PAGE_SHIFT;

then the two leftmost bits are dropped when storing the result in the
"random_variable". This variable shall be at least 34 bits long to hold
the (22+12) result.

These two dropped bits have an impact on the entropy of process stack.
Concretely, the total stack entropy is reduced by four: from 2^28 to
2^30 (One fourth of expected entropy).

This patch restores back the entropy by correcting the types involved
in the operations in the functions randomize_stack_top() and

The successful fix can be tested with:

  $ for i in `seq 1 10`; do cat /proc/self/maps | grep stack; done
  7ffeda566000-7ffeda587000 rw-p 00000000 00:00 0                          [stack]
  7fff5a332000-7fff5a353000 rw-p 00000000 00:00 0                          [stack]
  7ffcdb7a1000-7ffcdb7c2000 rw-p 00000000 00:00 0                          [stack]
  7ffd5e2c4000-7ffd5e2e5000 rw-p 00000000 00:00 0                          [stack]

Once corrected, the leading bytes should be between 7ffc and 7fff,
rather than always being 7fff.

Signed-off-by: Hector Marco-Gisbert <>
Signed-off-by: Ismael Ripoll <>
[ Rebased, fixed 80 char bugs, cleaned up commit message, added test example and CVE ]
Signed-off-by: Kees Cook <>
Cc: Linus Torvalds <>
Cc: Andrew Morton <>
Cc: Al Viro <>
Fixes: CVE-2015-1593
Signed-off-by: Borislav Petkov <>
Signed-off-by: Ben Hutchings <>
8 years agosched/autogroup: Fix failure to set cpu.rt_runtime_us
Peter Zijlstra [Mon, 9 Feb 2015 10:53:18 +0000 (11:53 +0100)]
sched/autogroup: Fix failure to set cpu.rt_runtime_us

commit 1fe89e1b6d270aa0d3452c60d38461ea589594e3 upstream.

Because task_group() uses a cache of autogroup_task_group(), whose
output depends on sched_class, switching classes can generate

In particular, when started as fair, the cache points to the
autogroup, so when switching to RT the tg_rt_schedulable() test fails
for every cpu.rt_{runtime,period}_us change because now the autogroup
has tasks and no runtime.

Furthermore, going back to the previous semantics of varying
task_group() with sched_class has the down-side that the sched_debug
output varies as well, even though the task really is in the

Therefore add an autogroup exception to tg_has_rt_tasks() -- such that
both (all) task_group() usages in sched/core now have one. And remove
all the remnants of the variable task_group() output.

Reported-by: Zefan Li <>
Signed-off-by: Peter Zijlstra (Intel) <>
Cc: Linus Torvalds <>
Cc: Mike Galbraith <>
Cc: Stefan Bader <>
Fixes: 8323f26ce342 ("sched: Fix race in task_group()")
Signed-off-by: Ingo Molnar <>
[bwh: Backported to 3.2: adjust filenames, context]
Signed-off-by: Ben Hutchings <>
8 years agodm snapshot: fix a possible invalid memory access on unload
Mikulas Patocka [Tue, 17 Feb 2015 19:34:00 +0000 (14:34 -0500)]
dm snapshot: fix a possible invalid memory access on unload

commit 22aa66a3ee5b61e0f4a0bfeabcaa567861109ec3 upstream.

When the snapshot target is unloaded, snapshot_dtr() waits until
pending_exceptions_count drops to zero.  Then, it destroys the snapshot.
Therefore, the function that decrements pending_exceptions_count
should not touch the snapshot structure after the decrement.

pending_complete() calls free_pending_exception(), which decrements
pending_exceptions_count, and then it performs up_write(&s->lock) and it
calls retry_origin_bios() which dereferences  s->origin.  These two
memory accesses to the fields of the snapshot may touch the dm_snapshot
struture after it is freed.

This patch moves the call to free_pending_exception() to the end of
pending_complete(), so that the snapshot will not be destroyed while
pending_complete() is in progress.

Signed-off-by: Mikulas Patocka <>
Signed-off-by: Mike Snitzer <>
Signed-off-by: Ben Hutchings <>
8 years agodm: fix a race condition in dm_get_md
Mikulas Patocka [Tue, 17 Feb 2015 19:30:53 +0000 (14:30 -0500)]
dm: fix a race condition in dm_get_md

commit 2bec1f4a8832e74ebbe859f176d8a9cb20dd97f4 upstream.

The function dm_get_md finds a device mapper device with a given dev_t,
increases the reference count and returns the pointer.

dm_get_md calls dm_find_md, dm_find_md takes _minor_lock, finds the
device, tests that the device doesn't have DMF_DELETING or DMF_FREEING
flag, drops _minor_lock and returns pointer to the device. dm_get_md then
calls dm_get. dm_get calls BUG if the device has the DMF_FREEING flag,
otherwise it increments the reference count.

There is a possible race condition - after dm_find_md exits and before
dm_get is called, there are no locks held, so the device may disappear or
DMF_FREEING flag may be set, which results in BUG.

To fix this bug, we need to call dm_get while we hold _minor_lock. This
patch renames dm_find_md to dm_get_md and changes it so that it calls
dm_get while holding the lock.

Signed-off-by: Mikulas Patocka <>
Signed-off-by: Mike Snitzer <>
Signed-off-by: Ben Hutchings <>
8 years agoIB/qib: Do not write EEPROM
Mitko Haralanov [Fri, 16 Jan 2015 13:55:27 +0000 (08:55 -0500)]
IB/qib: Do not write EEPROM

commit 18c0b82a3e4501511b08d0e8676fb08ac08734a3 upstream.

This changeset removes all the code that allows the driver to write to
the EEPROM and update the recorded error counters and power on hours.

These two stats are unused and writing them exposes a timing risk
which could leave the EEPROM in a bad state preventing further normal
operation of the HCA.

Reviewed-by: Mike Marciniszyn <>
Signed-off-by: Mitko Haralanov <>
Signed-off-by: Mike Marciniszyn <>
Signed-off-by: Roland Dreier <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agonetfilter: xt_socket: fix a stack corruption bug
Eric Dumazet [Mon, 16 Feb 2015 03:03:45 +0000 (19:03 -0800)]
netfilter: xt_socket: fix a stack corruption bug

commit 78296c97ca1fd3b104f12e1f1fbc06c46635990b upstream.

As soon as extract_icmp6_fields() returns, its local storage (automatic
variables) is deallocated and can be overwritten.

Lets add an additional parameter to make sure storage is valid long

While we are at it, adds some const qualifiers.

Signed-off-by: Eric Dumazet <>
Fixes: b64c9256a9b76 ("tproxy: added IPv6 support to the socket match")
Signed-off-by: Pablo Neira Ayuso <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agosg: fix read() error reporting
Tony Battersby [Wed, 11 Feb 2015 16:32:06 +0000 (11:32 -0500)]
sg: fix read() error reporting

commit 3b524a683af8991b4eab4182b947c65f0ce1421b upstream.

Fix SCSI generic read() incorrectly returning success after detecting an

Signed-off-by: Tony Battersby <>
Acked-by: Douglas Gilbert <>
Signed-off-by: James Bottomley <>
Signed-off-by: Ben Hutchings <>
8 years agofixed invalid assignment of 64bit mask to host dma_boundary for scatter gather segmen...
Minh Duc Tran [Mon, 9 Feb 2015 18:54:09 +0000 (18:54 +0000)]
fixed invalid assignment of 64bit mask to host dma_boundary for scatter gather segment boundary limit.

commit f76a610a8b4b6280eaedf48f3af9d5d74e418b66 upstream.

In reference to bug
Assert is seen with AMD cpu whenever calling pci_alloc_consistent.

[   29.406183] ------------[ cut here ]------------
[   29.410505] kernel BUG at lib/iommu-helper.c:13!

Signed-off-by: Minh Tran <>
Fixes: 6733b39a1301b0b020bbcbf3295852e93e624cb1
Signed-off-by: James Bottomley <>
Signed-off-by: Ben Hutchings <>
8 years agoipv6: fix ipv6_cow_metrics for non DST_HOST case
Martin KaFai Lau [Fri, 13 Feb 2015 00:14:08 +0000 (16:14 -0800)]
ipv6: fix ipv6_cow_metrics for non DST_HOST case

commit 3b4711757d7903ab6fa88a9e7ab8901b8227da60 upstream.

ipv6_cow_metrics() currently assumes only DST_HOST routes require
dynamic metrics allocation from inetpeer.  The assumption breaks
when ndisc discovered router with RTAX_MTU and RTAX_HOPLIMIT metric.
Refer to ndisc_router_discovery() in ndisc.c and note that dst_metric_set()
is called after the route is created.

This patch creates the metrics array (by calling dst_cow_metrics_generic) in

interface qemubr0
AdvLinkMTU 1300;
AdvCurHopLimit 30;

prefix fd00:face:face:face::/64
AdvOnLink on;
AdvAutonomous on;
AdvRouterAddr off;

[root@qemu1 ~]# ip -6 r show | egrep -v unreachable
fd00:face:face:face::/64 dev eth0  proto kernel  metric 256  expires 27sec
fe80::/64 dev eth0  proto kernel  metric 256
default via fe80::74df:d0ff:fe23:8ef2 dev eth0  proto ra  metric 1024  expires 27sec

[root@qemu1 ~]# ip -6 r show | egrep -v unreachable
fd00:face:face:face::/64 dev eth0  proto kernel  metric 256  expires 27sec mtu 1300
fe80::/64 dev eth0  proto kernel  metric 256  mtu 1300
default via fe80::74df:d0ff:fe23:8ef2 dev eth0  proto ra  metric 1024  expires 27sec mtu 1300 hoplimit 30

Fixes: 8e2ec639173f325 (ipv6: don't use inetpeer to store metrics for routes.)
Signed-off-by: Martin KaFai Lau <>
Signed-off-by: David S. Miller <>
Signed-off-by: Ben Hutchings <>
8 years agodm io: reject unsupported DISCARD requests with EOPNOTSUPP
Darrick J. Wong [Fri, 13 Feb 2015 19:05:37 +0000 (11:05 -0800)]
dm io: reject unsupported DISCARD requests with EOPNOTSUPP

commit 37527b869207ad4c208b1e13967d69b8bba1fbf9 upstream.

I created a dm-raid1 device backed by a device that supports DISCARD
and another device that does NOT support DISCARD with the following
dm configuration:

 #  echo '0 2048 mirror core 1 512 2 /dev/sda 0 /dev/sdb 0' | dmsetup create moo
 # lsblk -D
 sda                 0        4K       1G         0
 `-moo (dm-0)        0        4K       1G         0
 sdb                 0        0B       0B         0
 `-moo (dm-0)        0        4K       1G         0

Notice that the mirror device /dev/mapper/moo advertises DISCARD
support even though one of the mirror halves doesn't.

If I issue a DISCARD request (via fstrim, mount -o discard, or ioctl
BLKDISCARD) through the mirror, kmirrord gets stuck in an infinite
loop in do_region() when it tries to issue a DISCARD request to sdb.
The problem is that when we call do_region() against sdb, num_sectors
is set to zero because q->limits.max_discard_sectors is zero.
Therefore, "remaining" never decreases and the loop never terminates.

To fix this: before entering the loop, check for the combination of
REQ_DISCARD and no discard and return -EOPNOTSUPP to avoid hanging up
the mirror device.

This bug was found by the unfortunate coincidence of pvmove and a
discard operation in the RHEL 6.5 kernel; upstream is also affected.

Signed-off-by: Darrick J. Wong <>
Acked-by: "Martin K. Petersen" <>
Signed-off-by: Mike Snitzer <>
Signed-off-by: Ben Hutchings <>
8 years agodm mirror: do not degrade the mirror on discard error
Mikulas Patocka [Thu, 12 Feb 2015 15:09:20 +0000 (10:09 -0500)]
dm mirror: do not degrade the mirror on discard error

commit f2ed51ac64611d717d1917820a01930174c2f236 upstream.

It may be possible that a device claims discard support but it rejects
discards with -EOPNOTSUPP.  It happens when using loopback on ext2/ext3
filesystem driven by the ext4 driver.  It may also happen if the
underlying devices are moved from one disk on another.

If discard error happens, we reject the bio with -EOPNOTSUPP, but we do
not degrade the array.

This patch fixes failed test shell/ in the
lvm2 testsuite if the testsuite is extracted on an ext2 or ext3
filesystem and it is being driven by the ext4 driver.

Signed-off-by: Mikulas Patocka <>
Signed-off-by: Mike Snitzer <>
Signed-off-by: Ben Hutchings <>
8 years agojffs2: fix handling of corrupted summary length
Chen Jie [Tue, 10 Feb 2015 20:49:48 +0000 (12:49 -0800)]
jffs2: fix handling of corrupted summary length

commit 164c24063a3eadee11b46575c5482b2f1417be49 upstream.

sm->offset maybe wrong but magic maybe right, the offset do not have CRC.

Badness at c00c7580 [verbose debug info unavailable]
NIP: c00c7580 LR: c00c718c CTR: 00000014
REGS: df07bb40 TRAP: 0700   Not tainted  (
MSR: 00029000 <EE,ME,CE>  CR: 22084f84  XER: 00000000
TASK = df84d6e0[908] 'mount' THREAD: df07a000
GPR00: 00000001 df07bbf0 df84d6e0 00000000 00000001 00000000 df07bb58 00000041
GPR08: 00000041 c0638860 00000000 00000010 22084f88 100636c8 df814ff8 00000000
GPR16: df84d6e0 dfa558cc c05adb90 00000048 c0452d30 00000000 000240d0 000040d0
GPR24: 00000014 c05ae734 c05be2e0 00000000 00000001 00000000 00000000 c05ae730
NIP [c00c7580] __alloc_pages_nodemask+0x4d0/0x638
LR [c00c718c] __alloc_pages_nodemask+0xdc/0x638
Call Trace:
[df07bbf0] [c00c718c] __alloc_pages_nodemask+0xdc/0x638 (unreliable)
[df07bc90] [c00c7708] __get_free_pages+0x20/0x48
[df07bca0] [c00f4a40] __kmalloc+0x15c/0x1ec
[df07bcd0] [c01fc880] jffs2_scan_medium+0xa58/0x14d0
[df07bd70] [c01ff38c] jffs2_do_mount_fs+0x1f4/0x6b4
[df07bdb0] [c020144c] jffs2_do_fill_super+0xa8/0x260
[df07bdd0] [c020230c] jffs2_fill_super+0x104/0x184
[df07be00] [c0335814] get_sb_mtd_aux+0x9c/0xec
[df07be20] [c033596c] get_sb_mtd+0x84/0x1e8
[df07be60] [c0201ed0] jffs2_get_sb+0x1c/0x2c
[df07be70] [c0103898] vfs_kern_mount+0x78/0x1e8
[df07bea0] [c0103a58] do_kern_mount+0x40/0x100
[df07bec0] [c011fe90] do_mount+0x240/0x890
[df07bf10] [c0120570] sys_mount+0x90/0xd8
[df07bf40] [c00110d8] ret_from_syscall+0x0/0x4

=== Exception: c01 at 0xff61a34
    LR = 0x100135f0
Instruction dump:
38800005 38600000 48010f41 4bfffe1c 4bfc2d15 4bfffe8c 72e90200 4082fc28
3d20c064 39298860 8809000d 68000001 <0f0000002f800000 419efc0c 38000001
mount: mounting /dev/mtdblock3 on /common failed: Input/output error

Signed-off-by: Chen Jie <>
Signed-off-by: Andrew Morton <>
Signed-off-by: David Woodhouse <>
Signed-off-by: Ben Hutchings <>
8 years agoALSA: hdspm - Constrain periods to 2 on older cards
Adrian Knoth [Tue, 10 Feb 2015 10:33:50 +0000 (11:33 +0100)]
ALSA: hdspm - Constrain periods to 2 on older cards

commit f0153c3d948c1764f6c920a0675d86fc1d75813e upstream.

RME RayDAT and AIO use a fixed buffer size of 16384 samples. With period
sizes of 32-4096, this translates to 4-512 periods.

The older RME cards have a variable buffer size but require exactly two

This patch enforces nperiods=2 on those cards.

Signed-off-by: Adrian Knoth <>
Signed-off-by: Takashi Iwai <>
Signed-off-by: Ben Hutchings <>
8 years agodrm/radeon/dp: Set EDP_CONFIGURATION_SET for bridge chips if necessary
Alex Deucher [Wed, 11 Feb 2015 23:34:36 +0000 (18:34 -0500)]
drm/radeon/dp: Set EDP_CONFIGURATION_SET for bridge chips if necessary

commit 66c2b84ba6256bc5399eed45582af9ebb3ba2c15 upstream.

Don't restrict it to just eDP panels.  Some LVDS bridge chips require
this.  Fixes blank panels on resume on certain laptops.  Noticed
by mrnuke on IRC.


Signed-off-by: Alex Deucher <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agomm/memory.c: actually remap enough memory
Grazvydas Ignotas [Thu, 12 Feb 2015 23:00:19 +0000 (15:00 -0800)]
mm/memory.c: actually remap enough memory

commit 9cb12d7b4ccaa976f97ce0c5fd0f1b6a83bc2a75 upstream.

For whatever reason, generic_access_phys() only remaps one page, but
actually allows to access arbitrary size.  It's quite easy to trigger
large reads, like printing out large structure with gdb, which leads to a
crash.  Fix it by remapping correct size.

Fixes: 28b2ee20c7cb ("access_process_vm device memory infrastructure")
Signed-off-by: Grazvydas Ignotas <>
Cc: Rik van Riel <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
8 years agoiscsi-target: Drop problematic active_ts_list usage
Nicholas Bellinger [Thu, 22 Jan 2015 08:56:53 +0000 (00:56 -0800)]
iscsi-target: Drop problematic active_ts_list usage

commit 3fd7b60f2c7418239d586e359e0c6d8503e10646 upstream.

This patch drops legacy active_ts_list usage within iscsi_target_tq.c
code.  It was originally used to track the active thread sets during
iscsi-target shutdown, and is no longer used by modern upstream code.

Two people have reported list corruption using traditional iscsi-target
and iser-target with the following backtrace, that appears to be related
to iscsi_thread_set->ts_list being used across both active_ts_list and

[   60.782534] ------------[ cut here ]------------
[   60.782543] WARNING: CPU: 0 PID: 9430 at lib/list_debug.c:53 __list_del_entry+0x63/0xd0()
[   60.782545] list_del corruption, ffff88045b00d180->next is LIST_POISON1 (dead000000100100)
[   60.782546] Modules linked in: ib_srpt tcm_qla2xxx qla2xxx tcm_loop tcm_fc libfc scsi_transport_fc scsi_tgt ib_isert rdma_cm iw_cm ib_addr iscsi_target_mod target_core_pscsi target_core_file target_core_iblock target_core_mod configfs ebtable_nat ebtables ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 ipt_REJECT xt_CHECKSUM iptable_mangle iptable_filter ip_tables bridge stp llc autofs4 sunrpc ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 ib_ipoib ib_cm ib_uverbs ib_umad mlx4_en mlx4_ib ib_sa ib_mad ib_core mlx4_core dm_mirror dm_region_hash dm_log dm_mod vhost_net macvtap macvlan vhost tun kvm_intel kvm uinput iTCO_wdt iTCO_vendor_support microcode serio_raw pcspkr sb_edac edac_core sg i2c_i801 lpc_ich mfd_core mtip32xx igb i2c_algo_bit i2c_core ptp pps_core ioatdma dca wmi ext3(F) jbd(F) mbcache(F) sd_mod(F) crc_t10dif(F) crct10dif_common(F) ahci(F) libahci(F) isci(F) libsas(F) scsi_transport_sas(F) [last unloaded: speedstep_lib]
[   60.782597] CPU: 0 PID: 9430 Comm: iscsi_ttx Tainted: GF 3.12.19+ #2
[   60.782598] Hardware name: Supermicro X9DRX+-F/X9DRX+-F, BIOS 3.00 07/09/2013
[   60.782599]  0000000000000035 ffff88044de31d08 ffffffff81553ae7 0000000000000035
[   60.782602]  ffff88044de31d58 ffff88044de31d48 ffffffff8104d1cc 0000000000000002
[   60.782605]  ffff88045b00d180 ffff88045b00d0c0 ffff88045b00d0c0 ffff88044de31e58
[   60.782607] Call Trace:
[   60.782611]  [<ffffffff81553ae7>] dump_stack+0x49/0x62
[   60.782615]  [<ffffffff8104d1cc>] warn_slowpath_common+0x8c/0xc0
[   60.782618]  [<ffffffff8104d2b6>] warn_slowpath_fmt+0x46/0x50
[   60.782620]  [<ffffffff81280933>] __list_del_entry+0x63/0xd0
[   60.782622]  [<ffffffff812809b1>] list_del+0x11/0x40
[   60.782630]  [<ffffffffa06e7cf9>] iscsi_del_ts_from_active_list+0x29/0x50 [iscsi_target_mod]
[   60.782635]  [<ffffffffa06e87b1>] iscsi_tx_thread_pre_handler+0xa1/0x180 [iscsi_target_mod]
[   60.782642]  [<ffffffffa06fb9ae>] iscsi_target_tx_thread+0x4e/0x220 [iscsi_target_mod]
[   60.782647]  [<ffffffffa06fb960>] ? iscsit_handle_snack+0x190/0x190 [iscsi_target_mod]
[   60.782652]  [<ffffffffa06fb960>] ? iscsit_handle_snack+0x190/0x190 [iscsi_target_mod]
[   60.782655]  [<ffffffff8106f99e>] kthread+0xce/0xe0
[   60.782657]  [<ffffffff8106f8d0>] ? kthread_freezable_should_stop+0x70/0x70
[   60.782660]  [<ffffffff8156026c>] ret_from_fork+0x7c/0xb0
[   60.782662]  [<ffffffff8106f8d0>] ? kthread_freezable_should_stop+0x70/0x70
[   60.782663] ---[ end trace 9662f4a661d33965 ]---

Since this code is no longer used, go ahead and drop the problematic usage

Reported-by: Gavin Guo <>
Reported-by: Moussa Ba <>
Signed-off-by: Nicholas Bellinger <>
[bwh: Backported to 3.2:
 - Adjust context
 - Also delete redundant initialisation, deleted upstream in commit
   d0f474e50192 ('target: Use LIST_HEAD()/DEFINE_MUTEX() for static objects')]
Signed-off-by: Ben Hutchings <>
8 years agomm/nommu.c: fix arithmetic overflow in __vm_enough_memory()
Roman Gushchin [Wed, 11 Feb 2015 23:28:42 +0000 (15:28 -0800)]
mm/nommu.c: fix arithmetic overflow in __vm_enough_memory()

commit 8138a67a5557ffea3a21dfd6f037842d4e748513 upstream.

I noticed that "allowed" can easily overflow by falling below 0, because
(total_vm / 32) can be larger than "allowed".  The problem occurs in

In this case, a huge allocation can success and overcommit the system
(despite OVERCOMMIT_NONE mode).  All subsequent allocations will fall
(system-wide), so system become unusable.

The problem was masked out by commit c9b1d0981fcc
("mm: limit growth of 3% hardcoded other user reserve"),
but it's easy to reproduce it on older kernels:
1) set overcommit_memory sysctl to 2
2) mmap() large file multiple times (with VM_SHARED flag)
3) try to malloc() large amount of memory

It also can be reproduced on newer kernels, but miss-configured
sysctl_user_reserve_kbytes is required.

Fix this issue by switching to signed arithmetic here.

Signed-off-by: Roman Gushchin <>
Cc: Andrew Shewmaker <>
Cc: Rik van Riel <>
Cc: Konstantin Khlebnikov <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
[bwh: Backported to 3.2: there is no 'reserved' variable]
Signed-off-by: Ben Hutchings <>
8 years agomm/mmap.c: fix arithmetic overflow in __vm_enough_memory()
Roman Gushchin [Wed, 11 Feb 2015 23:28:39 +0000 (15:28 -0800)]
mm/mmap.c: fix arithmetic overflow in __vm_enough_memory()

commit 5703b087dc8eaf47bfb399d6cf512d471beff405 upstream.

I noticed, that "allowed" can easily overflow by falling below 0,
because (total_vm / 32) can be larger than "allowed".  The problem
occurs in OVERCOMMIT_NONE mode.

In this case, a huge allocation can success and overcommit the system
(despite OVERCOMMIT_NONE mode).  All subsequent allocations will fall
(system-wide), so system become unusable.

The problem was masked out by commit c9b1d0981fcc
("mm: limit growth of 3% hardcoded other user reserve"),
but it's easy to reproduce it on older kernels:
1) set overcommit_memory sysctl to 2
2) mmap() large file multiple times (with VM_SHARED flag)
3) try to malloc() large amount of memory

It also can be reproduced on newer kernels, but miss-configured
sysctl_user_reserve_kbytes is required.

Fix this issue by switching to signed arithmetic here.

[ use min_t]
Signed-off-by: Roman Gushchin <>
Cc: Andrew Shewmaker <>
Cc: Rik van Riel <>
Cc: Konstantin Khlebnikov <>
Reviewed-by: Michal Hocko <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
[bwh: Backported to 3.2: there is no 'reserved' variable]
Signed-off-by: Ben Hutchings <>
8 years agomm/hugetlb: add migration entry check in __unmap_hugepage_range
Naoya Horiguchi [Wed, 11 Feb 2015 23:25:32 +0000 (15:25 -0800)]
mm/hugetlb: add migration entry check in __unmap_hugepage_range

commit 9fbc1f635fd0bd28cb32550211bf095753ac637a upstream.

If __unmap_hugepage_range() tries to unmap the address range over which
hugepage migration is on the way, we get the wrong page because pte_page()
doesn't work for migration entries.  This patch simply clears the pte for
migration entries as we do for hwpoison entries.

Fixes: 290408d4a2 ("hugetlb: hugepage migration core")
Signed-off-by: Naoya Horiguchi <>
Cc: Hugh Dickins <>
Cc: James Hogan <>
Cc: David Rientjes <>
Cc: Mel Gorman <>
Cc: Johannes Weiner <>
Cc: Michal Hocko <>
Cc: Rik van Riel <>
Cc: Andrea Arcangeli <>
Cc: Luiz Capitulino <>
Cc: Nishanth Aravamudan <>
Cc: Lee Schermerhorn <>
Cc: Steve Capper <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
[bwh: Backported to 3.2: adjust context and comment, as we're checking after
 the PTE has been cleared]
Signed-off-by: Ben Hutchings <>
8 years agomm/hugetlb: add migration/hwpoisoned entry check in hugetlb_change_protection
Naoya Horiguchi [Wed, 11 Feb 2015 23:25:28 +0000 (15:25 -0800)]
mm/hugetlb: add migration/hwpoisoned entry check in hugetlb_change_protection

commit a8bda28d87c38c6aa93de28ba5d30cc18e865a11 upstream.

There is a race condition between hugepage migration and
change_protection(), where hugetlb_change_protection() doesn't care about
migration entries and wrongly overwrites them.  That causes unexpected
results like kernel crash.  HWPoison entries also can cause the same

This patch adds is_hugetlb_entry_(migration|hwpoisoned) check in this
function to do proper actions.

Fixes: 290408d4a2 ("hugetlb: hugepage migration core")
Signed-off-by: Naoya Horiguchi <>
Cc: Hugh Dickins <>
Cc: James Hogan <>
Cc: David Rientjes <>
Cc: Mel Gorman <>
Cc: Johannes Weiner <>
Cc: Michal Hocko <>
Cc: Rik van Riel <>
Cc: Andrea Arcangeli <>
Cc: Luiz Capitulino <>
Cc: Nishanth Aravamudan <>
Cc: Lee Schermerhorn <>
Cc: Steve Capper <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
[bwh: Backported to 3.2:
 - Adjust context
 - We don't have split page table locks, so don't unlock inside the loop
 - We don't count pages here]
Signed-off-by: Ben Hutchings <>
8 years agomm/hugetlb: fix getting refcount 0 page in hugetlb_fault()
Naoya Horiguchi [Wed, 11 Feb 2015 23:25:25 +0000 (15:25 -0800)]
mm/hugetlb: fix getting refcount 0 page in hugetlb_fault()

commit 0f792cf949a0be506c2aa8bfac0605746b146dda upstream.

When running the test which causes the race as shown in the previous patch,
we can hit the BUG "get_page() on refcount 0 page" in hugetlb_fault().

This race happens when pte turns into migration entry just after the first
check of is_hugetlb_entry_migration() in hugetlb_fault() passed with false.
To fix this, we need to check pte_present() again after huge_ptep_get().

This patch also reorders taking ptl and doing pte_page(), because
pte_page() should be done in ptl.  Due to this reordering, we need use
trylock_page() in page != pagecache_page case to respect locking order.

Fixes: 66aebce747ea ("hugetlb: fix race condition in hugetlb_fault()")
Signed-off-by: Naoya Horiguchi <>
Cc: Hugh Dickins <>
Cc: James Hogan <>
Cc: David Rientjes <>
Cc: Mel Gorman <>
Cc: Johannes Weiner <>
Cc: Michal Hocko <>
Cc: Rik van Riel <>
Cc: Andrea Arcangeli <>
Cc: Luiz Capitulino <>
Cc: Nishanth Aravamudan <>
Cc: Lee Schermerhorn <>
Cc: Steve Capper <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
[bwh: Backported to 3.2:
 - Adjust context
 - Error label is named 'out_page_table_lock' not 'out_ptl']
Signed-off-by: Ben Hutchings <>
8 years agocpufreq: speedstep-smi: enable interrupts when waiting
Mikulas Patocka [Mon, 9 Feb 2015 18:38:17 +0000 (13:38 -0500)]
cpufreq: speedstep-smi: enable interrupts when waiting

commit d4d4eda23794c701442e55129dd4f8f2fefd5e4d upstream.

On Dell Latitude C600 laptop with Pentium 3 850MHz processor, the
speedstep-smi driver sometimes loads and sometimes doesn't load with
"change to state X failed" message.

The hardware sometimes refuses to change frequency and in this case, we
need to retry later. I found out that we need to enable interrupts while
waiting. When we enable interrupts, the hardware blockage that prevents
frequency transition resolves and the transition is possible. With
disabled interrupts, the blockage doesn't resolve (no matter how long do
we wait). The exact reasons for this hardware behavior are unknown.

This patch enables interrupts in the function speedstep_set_state that can
be called with disabled interrupts. However, this function is called with
disabled interrupts only from speedstep_get_freqs, so it shouldn't cause
any problem.

Signed-off-by: Mikulas Patocka <
Acked-by: Viresh Kumar <>
Signed-off-by: Rafael J. Wysocki <>
Signed-off-by: Ben Hutchings <>
8 years agoNFSv4.1: Fix a kfree() of uninitialised pointers in decode_cb_sequence_args
Trond Myklebust [Wed, 11 Feb 2015 22:27:55 +0000 (17:27 -0500)]
NFSv4.1: Fix a kfree() of uninitialised pointers in decode_cb_sequence_args

commit d8ba1f971497c19cf80da1ea5391a46a5f9fbd41 upstream.

If the call to decode_rc_list() fails due to a memory allocation error,
then we need to truncate the array size to ensure that we only call
kfree() on those pointer that were allocated.

Reported-by: David Ramos <>
Fixes: 4aece6a19cf7f ("nfs41: cb_sequence xdr implementation")
Signed-off-by: Trond Myklebust <>
Signed-off-by: Ben Hutchings <>
8 years agofsnotify: fix handling of renames in audit
Jan Kara [Tue, 10 Feb 2015 22:08:32 +0000 (14:08 -0800)]
fsnotify: fix handling of renames in audit

commit 6ee8e25fc3e916193bce4ebb43d5439e1e2144ab upstream.

Commit e9fd702a58c4 ("audit: convert audit watches to use fsnotify
instead of inotify") broke handling of renames in audit.  Audit code
wants to update inode number of an inode corresponding to watched name
in a directory.  When something gets renamed into a directory to a
watched name, inotify previously passed moved inode to audit code
however new fsnotify code passes directory inode where the change
happened.  That confuses audit and it starts watching parent directory
instead of a file in a directory.

This can be observed for example by doing:

  cd /tmp
  touch foo bar
  auditctl -w /tmp/foo
  touch foo
  mv bar foo
  touch foo

In audit log we see events like:

  type=CONFIG_CHANGE msg=audit(1423563584.155:90): auid=1000 ses=2 op="updated rules" path="/tmp/foo" key=(null) list=4 res=1
  type=PATH msg=audit(1423563584.155:91): item=2 name="bar" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE
  type=PATH msg=audit(1423563584.155:91): item=3 name="foo" inode=1046842 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=DELETE
  type=PATH msg=audit(1423563584.155:91): item=4 name="foo" inode=1046884 dev=08:0 2 mode=0100644 ouid=0 ogid=0 rdev=00:00 nametype=CREATE

and that's it - we see event for the first touch after creating the
audit rule, we see events for rename but we don't see any event for the
last touch.  However we start seeing events for unrelated stuff
happening in /tmp.

Fix the problem by passing moved inode as data in the FS_MOVED_FROM and
FS_MOVED_TO events instead of the directory where the change happens.
This doesn't introduce any new problems because noone besides
audit_watch.c cares about the passed value:

  fs/notify/fanotify/fanotify.c cares only about FSNOTIFY_EVENT_PATH events.
  fs/notify/dnotify/dnotify.c doesn't care about passed 'data' value at all.
  fs/notify/inotify/inotify_fsnotify.c uses 'data' only for FSNOTIFY_EVENT_PATH.
  kernel/audit_tree.c doesn't care about passed 'data' at all.
  kernel/audit_watch.c expects moved inode as 'data'.

Fixes: e9fd702a58c49db ("audit: convert audit watches to use fsnotify instead of inotify")
Signed-off-by: Jan Kara <>
Cc: Paul Moore <>
Cc: Eric Paris <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
8 years agoALSA: off by one bug in snd_riptide_joystick_probe()
Dan Carpenter [Mon, 9 Feb 2015 13:51:40 +0000 (16:51 +0300)]
ALSA: off by one bug in snd_riptide_joystick_probe()

commit e4940626defdf6c92da1052ad3f12741c1a28c90 upstream.

The problem here is that we check:

if (dev >= SNDRV_CARDS)

Then we increment "dev".

       if (!joystick_port[dev++])

Then we use it as an offset into a array with SNDRV_CARDS elements.

if (!request_region(joystick_port[dev], 8, "Riptide gameport")) {

This has 3 effects:
1) If you use the module option to specify the joystick port then it has
   to be shifted one space over.
2) The wrong error message will be printed on failure if you have over
   32 cards.
3) Static checkers will correctly complain that are off by one.

Fixes: db1005ec6ff8 ('ALSA: riptide - Fix joystick resource handling')
Signed-off-by: Dan Carpenter <>
Signed-off-by: Takashi Iwai <>
Signed-off-by: Ben Hutchings <>
8 years agortnetlink: ifla_vf_policy: fix misuses of NLA_BINARY
Daniel Borkmann [Thu, 5 Feb 2015 17:44:04 +0000 (18:44 +0100)]
rtnetlink: ifla_vf_policy: fix misuses of NLA_BINARY

commit 364d5716a7adb91b731a35765d369602d68d2881 upstream.

ifla_vf_policy[] is wrong in advertising its individual member types as
NLA_BINARY since .type = NLA_BINARY in combination with .len declares the
len member as *max* attribute length [0, len].

The issue is that when do_setvfinfo() is being called to set up a VF
through ndo handler, we could set corrupted data if the attribute length
is less than the size of the related structure itself.

The intent is exactly the opposite, namely to make sure to pass at least
data of minimum size of len.

Fixes: ebc08a6f47ee ("rtnetlink: Add VF config code to rtnetlink")
Cc: Mitch Williams <>
Cc: Jeff Kirsher <>
Signed-off-by: Daniel Borkmann <>
Acked-by: Thomas Graf <>
Signed-off-by: David S. Miller <>
[bwh: Backported to 3.2: drop the unsupported attributes]
Signed-off-by: Ben Hutchings <>
8 years agoxen/manage: Fix USB interaction issues when resuming
Ross Lagerwall [Mon, 19 Jan 2015 13:19:38 +0000 (13:19 +0000)]
xen/manage: Fix USB interaction issues when resuming

commit 72978b2fe2f2cdf9f319c6c6dcdbe92b38de2be2 upstream.

Commit 61a734d305e1 ("xen/manage: Always freeze/thaw processes when
suspend/resuming") ensured that userspace processes were always frozen
before suspending to reduce interaction issues when resuming devices.
However, freeze_processes() does not freeze kernel threads.  Freeze
kernel threads as well to prevent deadlocks with the khubd thread when
resuming devices.

This is what native suspend and resume does.

Example deadlock:
[ 7279.648010]  [<ffffffff81446bde>] ? xen_poll_irq_timeout+0x3e/0x50
[ 7279.648010]  [<ffffffff81448d60>] xen_poll_irq+0x10/0x20
[ 7279.648010]  [<ffffffff81011723>] xen_lock_spinning+0xb3/0x120
[ 7279.648010]  [<ffffffff810115d1>] __raw_callee_save_xen_lock_spinning+0x11/0x20
[ 7279.648010]  [<ffffffff815620b6>] ? usb_control_msg+0xe6/0x120
[ 7279.648010]  [<ffffffff81747e50>] ? _raw_spin_lock_irq+0x50/0x60
[ 7279.648010]  [<ffffffff8174522c>] wait_for_completion+0xac/0x160
[ 7279.648010]  [<ffffffff8109c520>] ? try_to_wake_up+0x2c0/0x2c0
[ 7279.648010]  [<ffffffff814b60f2>] dpm_wait+0x32/0x40
[ 7279.648010]  [<ffffffff814b6eb0>] device_resume+0x90/0x210
[ 7279.648010]  [<ffffffff814b7d71>] dpm_resume+0x121/0x250
[ 7279.648010]  [<ffffffff8144c570>] ? xenbus_dev_request_and_reply+0xc0/0xc0
[ 7279.648010]  [<ffffffff814b80d5>] dpm_resume_end+0x15/0x30
[ 7279.648010]  [<ffffffff81449fba>] do_suspend+0x10a/0x200
[ 7279.648010]  [<ffffffff8144a2f0>] ? xen_pre_suspend+0x20/0x20
[ 7279.648010]  [<ffffffff8144a1d0>] shutdown_handler+0x120/0x150
[ 7279.648010]  [<ffffffff8144c60f>] xenwatch_thread+0x9f/0x160
[ 7279.648010]  [<ffffffff810ac510>] ? finish_wait+0x80/0x80
[ 7279.648010]  [<ffffffff8108d189>] kthread+0xc9/0xe0
[ 7279.648010]  [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80
[ 7279.648010]  [<ffffffff8175087c>] ret_from_fork+0x7c/0xb0
[ 7279.648010]  [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80

[ 7441.216287] INFO: task khubd:89 blocked for more than 120 seconds.
[ 7441.219457]       Tainted: G            X #1
[ 7441.222176] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 7441.225827] khubd           D ffff88003f433440     0    89      2 0x00000000
[ 7441.229258]  ffff88003ceb9b98 0000000000000046 ffff88003ce83000 0000000000013440
[ 7441.232959]  ffff88003ceb9fd8 0000000000013440 ffff88003cd13000 ffff88003ce83000
[ 7441.236658]  0000000000000286 ffff88003d3e0000 ffff88003ceb9bd0 00000001001aa01e
[ 7441.240415] Call Trace:
[ 7441.241614]  [<ffffffff817442f9>] schedule+0x29/0x70
[ 7441.243930]  [<ffffffff81743406>] schedule_timeout+0x166/0x2c0
[ 7441.246681]  [<ffffffff81075b80>] ? call_timer_fn+0x110/0x110
[ 7441.249339]  [<ffffffff8174357e>] schedule_timeout_uninterruptible+0x1e/0x20
[ 7441.252644]  [<ffffffff81077710>] msleep+0x20/0x30
[ 7441.254812]  [<ffffffff81555f00>] hub_port_reset+0xf0/0x580
[ 7441.257400]  [<ffffffff81558465>] hub_port_init+0x75/0xb40
[ 7441.259981]  [<ffffffff814bb3c9>] ? update_autosuspend+0x39/0x60
[ 7441.262817]  [<ffffffff814bb4f0>] ? pm_runtime_set_autosuspend_delay+0x50/0xa0
[ 7441.266212]  [<ffffffff8155a64a>] hub_thread+0x71a/0x1750
[ 7441.268728]  [<ffffffff810ac510>] ? finish_wait+0x80/0x80
[ 7441.271272]  [<ffffffff81559f30>] ? usb_port_resume+0x670/0x670
[ 7441.274067]  [<ffffffff8108d189>] kthread+0xc9/0xe0
[ 7441.276305]  [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80
[ 7441.279131]  [<ffffffff8175087c>] ret_from_fork+0x7c/0xb0
[ 7441.281659]  [<ffffffff8108d0c0>] ? flush_kthread_worker+0x80/0x80

Signed-off-by: Ross Lagerwall <>
Signed-off-by: David Vrabel <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agolmedm04: Fix usb_submit_urb BOGUS urb xfer, pipe 1 != type 3 in interrupt urb
Malcolm Priestley [Fri, 2 Jan 2015 13:56:28 +0000 (10:56 -0300)]
lmedm04: Fix usb_submit_urb BOGUS urb xfer, pipe 1 != type 3 in interrupt urb

commit 15e1ce33182d1d5dbd8efe8d382b9352dc857527 upstream.

A quirk of some older firmwares that report endpoint pipe type as PIPE_BULK
but the endpoint otheriwse functions as interrupt.

Check if usb_endpoint_type is USB_ENDPOINT_XFER_BULK and set as usb_rcvbulkpipe.

Signed-off-by: Malcolm Priestley <>
Signed-off-by: Mauro Carvalho Chehab <>
[bwh: Backported to 3.2:
 - Adjust filename, context
 - Add definition of the local variable 'd']
Signed-off-by: Ben Hutchings <>
8 years agotty: Prevent untrappable signals from malicious program
Peter Hurley [Mon, 19 Jan 2015 18:05:03 +0000 (13:05 -0500)]
tty: Prevent untrappable signals from malicious program

commit 37480a05685ed5b8e1b9bf5e5c53b5810258b149 upstream.

Commit 26df6d13406d1a5 ("tty: Add EXTPROC support for LINEMODE")
allows a process which has opened a pty master to send _any_ signal
to the process group of the pty slave. Although potentially
exploitable by a malicious program running a setuid program on
a pty slave, it's unknown if this exploit currently exists.

Limit to signals actually used.

Cc: Theodore Ts'o <>
Cc: Howard Chu <>
Cc: One Thousand Gnomes <>
Cc: Jiri Slaby <>
Signed-off-by: Peter Hurley <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
8 years agovt: provide notifications on selection changes
Nicolas Pitre [Fri, 23 Jan 2015 22:07:21 +0000 (17:07 -0500)]
vt: provide notifications on selection changes

commit 19e3ae6b4f07a87822c1c9e7ed99d31860e701af upstream.

The vcs device's poll/fasync support relies on the vt notifier to signal
changes to the screen content.  Notifier invocations were missing for
changes that comes through the selection interface though.  Fix that.

Tested with BRLTTY 5.2.

Signed-off-by: Nicolas Pitre <>
Cc: Dave Mielke <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
8 years agoUSB: fix use-after-free bug in usb_hcd_unlink_urb()
Alan Stern [Fri, 30 Jan 2015 17:58:26 +0000 (12:58 -0500)]
USB: fix use-after-free bug in usb_hcd_unlink_urb()

commit c99197902da284b4b723451c1471c45b18537cde upstream.

The usb_hcd_unlink_urb() routine in hcd.c contains two possible
use-after-free errors.  The dev_dbg() statement at the end of the
routine dereferences urb and urb->dev even though both structures may
have been deallocated.

This patch fixes the problem by storing urb->dev in a local variable
(avoiding the dereference of urb) and moving the dev_dbg() up before
the usb_put_dev() call.

Signed-off-by: Alan Stern <>
Reported-by: Joe Lawrence <>
Tested-by: Joe Lawrence <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
8 years agoUSB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
Alan Stern [Thu, 29 Jan 2015 20:05:04 +0000 (15:05 -0500)]
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)

commit 074f9dd55f9cab1b82690ed7e44bcf38b9616ce0 upstream.

Currently the USB stack assumes that all host controller drivers are
capable of receiving wakeup requests from downstream devices.
However, this isn't true for the isp1760-hcd driver, which means that
it isn't safe to do a runtime suspend of any device attached to a
root-hub port if the device requires wakeup.

This patch adds a "cant_recv_wakeups" flag to the usb_hcd structure
and sets the flag in isp1760-hcd.  The core is modified to prevent a
direct child of the root hub from being put into runtime suspend with
wakeup enabled if the flag is set.

Signed-off-by: Alan Stern <>
Tested-by: Nicolas Pitre <>
Signed-off-by: Greg Kroah-Hartman <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agocdc-acm: add sanity checks
Oliver Neukum [Wed, 28 Jan 2015 10:14:55 +0000 (11:14 +0100)]
cdc-acm: add sanity checks

commit 7e860a6e7aa62b337a61110430cd633db5b0d2dd upstream.

Check the special CDC headers for a plausible minimum length.
Another big operating systems ignores such garbage.

Signed-off-by: Oliver Neukum <>
Reviewed-by: Adam Lee <>
Tested-by: Adam Lee <>
Signed-off-by: Greg Kroah-Hartman <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agonfs: don't call blocking operations while !TASK_RUNNING
Jeff Layton [Wed, 14 Jan 2015 18:08:57 +0000 (13:08 -0500)]
nfs: don't call blocking operations while !TASK_RUNNING

commit 6ffa30d3f734d4f6b478081dfc09592021028f90 upstream.

Bruce reported seeing this warning pop when mounting using v4.1:

     ------------[ cut here ]------------
     WARNING: CPU: 1 PID: 1121 at kernel/sched/core.c:7300 __might_sleep+0xbd/0xd0()
    do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff810ff58f>] prepare_to_wait+0x2f/0x90
    Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace sunrpc fscache ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw snd_hda_codec_generic snd_hda_intel snd_hda_controller snd_hda_codec snd_hwdep snd_pcm snd_timer ppdev joydev snd virtio_console virtio_balloon pcspkr serio_raw parport_pc parport pvpanic floppy soundcore i2c_piix4 virtio_blk virtio_net qxl drm_kms_helper ttm drm virtio_pci virtio_ring ata_generic virtio pata_acpi
    CPU: 1 PID: 1121 Comm: nfsv4.1-svc Not tainted 3.19.0-rc4+ #25
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140709_153950- 04/01/2014
     0000000000000000 000000004e5e3f73 ffff8800b998fb48 ffffffff8186ac78
     0000000000000000 ffff8800b998fba0 ffff8800b998fb88 ffffffff810ac9da
     ffff8800b998fb68 ffffffff81c923e7 00000000000004d9 0000000000000000
    Call Trace:
     [<ffffffff8186ac78>] dump_stack+0x4c/0x65
     [<ffffffff810ac9da>] warn_slowpath_common+0x8a/0xc0
     [<ffffffff810aca65>] warn_slowpath_fmt+0x55/0x70
     [<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90
     [<ffffffff810ff58f>] ? prepare_to_wait+0x2f/0x90
     [<ffffffff810dd2ad>] __might_sleep+0xbd/0xd0
     [<ffffffff8124c973>] kmem_cache_alloc_trace+0x243/0x430
     [<ffffffff810d941e>] ? groups_alloc+0x3e/0x130
     [<ffffffff810d941e>] groups_alloc+0x3e/0x130
     [<ffffffffa0301b1e>] svcauth_unix_accept+0x16e/0x290 [sunrpc]
     [<ffffffffa0300571>] svc_authenticate+0xe1/0xf0 [sunrpc]
     [<ffffffffa02fc564>] svc_process_common+0x244/0x6a0 [sunrpc]
     [<ffffffffa02fd044>] bc_svc_process+0x1c4/0x260 [sunrpc]
     [<ffffffffa03d5478>] nfs41_callback_svc+0x128/0x1f0 [nfsv4]
     [<ffffffff810ff970>] ? wait_woken+0xc0/0xc0
     [<ffffffffa03d5350>] ? nfs4_callback_svc+0x60/0x60 [nfsv4]
     [<ffffffff810d45bf>] kthread+0x11f/0x140
     [<ffffffff810ea815>] ? local_clock+0x15/0x30
     [<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250
     [<ffffffff81874bfc>] ret_from_fork+0x7c/0xb0
     [<ffffffff810d44a0>] ? kthread_create_on_node+0x250/0x250
    ---[ end trace 675220a11e30f4f2 ]---

nfs41_callback_svc does most of its work while in TASK_INTERRUPTIBLE,
which is just wrong. Fix that by finishing the wait immediately if we've
found that the list has something on it.

Also, we don't expect this kthread to accept signals, so we should be
using a TASK_UNINTERRUPTIBLE sleep instead. That however, opens us up
hung task warnings from the watchdog, so have the schedule_timeout
wake up every 60s if there's no callback activity.

Reported-by: "J. Bruce Fields" <>
Signed-off-by: Jeff Layton <>
Signed-off-by: Trond Myklebust <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agoxprtrdma: Free the pd if ib_query_qp() fails
Chuck Lever [Wed, 21 Jan 2015 16:03:19 +0000 (11:03 -0500)]
xprtrdma: Free the pd if ib_query_qp() fails

commit 5ae711a24601257f395c1f8746ac95be0cbd75e5 upstream.

If ib_query_qp() fails or the memory registration mode isn't
supported, don't leak the PD. An orphaned IB/core resource will
cause IB module removal to hang.

Fixes: bd7ed1d13304 ("RPC/RDMA: check selected memory registration ...")
Signed-off-by: Chuck Lever <>
Reviewed-by: Steve Wise <>
Signed-off-by: Anna Schumaker <>
[bwh: Backported to 3.2:
 - Adjust context
 - There are only 2 goto's to be changed, not 3]
Signed-off-by: Ben Hutchings <>
8 years agoARM: 8284/1: sa1100: clear RCSR_SMR on resume
Dmitry Eremin-Solenikov [Thu, 15 Jan 2015 02:06:22 +0000 (03:06 +0100)]
ARM: 8284/1: sa1100: clear RCSR_SMR on resume

commit e461894dc2ce7778ccde1c3483c9b15a85a7fc5f upstream.

StrongARM core uses RCSR SMR bit to tell to bootloader that it was reset
by entering the sleep mode. After we have resumed, there is little point
in having that bit enabled. Moreover, if this bit is set before reboot,
the bootloader can become confused. Thus clear the SMR bit on resume
just before clearing the scratchpad (resume address) register.

Signed-off-by: Dmitry Eremin-Solenikov <>
Signed-off-by: Russell King <>
Signed-off-by: Ben Hutchings <>
8 years agostaging: comedi: comedi_compat32.c: fix COMEDI_CMD copy back
Ian Abbott [Tue, 27 Jan 2015 18:16:51 +0000 (18:16 +0000)]
staging: comedi: comedi_compat32.c: fix COMEDI_CMD copy back

commit 42b8ce6f55facfa101462e694d33fc6bca471138 upstream.

`do_cmd_ioctl()` in "comedi_fops.c" handles the `COMEDI_CMD` ioctl.
This returns `-EAGAIN` if it has copied a modified `struct comedi_cmd`
back to user-space.  (This occurs when the low-level Comedi driver's
`do_cmdtest()` handler returns non-zero to indicate a problem with the
contents of the `struct comedi_cmd`, or when the `struct comedi_cmd` has
the `CMDF_BOGUS` flag set.)

`compat_cmd()` in "comedi_compat32.c" handles the 32-bit compatible
version of the `COMEDI_CMD` ioctl.  Currently, it never copies a 32-bit
compatible version of `struct comedi_cmd` back to user-space, which is
at odds with the way the regular `COMEDI_CMD` ioctl is handled.  To fix
it, change `compat_cmd()` to copy a 32-bit compatible version of the
`struct comedi_cmd` back to user-space when the main ioctl handler
returns `-EAGAIN`.

Signed-off-by: Ian Abbott <>
Reviewed-by: H Hartley Sweeten <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
8 years agoiio: imu: adis16400: Fix sign extension
Rasmus Villemoes [Thu, 22 Jan 2015 23:34:02 +0000 (00:34 +0100)]
iio: imu: adis16400: Fix sign extension

commit 19e353f2b344ad86cea6ebbc0002e5f903480a90 upstream.

The intention is obviously to sign-extend a 12 bit quantity. But
because of C's promotion rules, the assignment is equivalent to "val16
&= 0xfff;". Use the proper API for this.

Signed-off-by: Rasmus Villemoes <>
Acked-by: Lars-Peter Clausen <>
Signed-off-by: Jonathan Cameron <>
[bwh: Backported to 3.2: adjust filename, context]
Signed-off-by: Ben Hutchings <>
8 years agoUSB: cp210x: add ID for RUGGEDCOM USB Serial Console
Lennart Sorensen [Wed, 21 Jan 2015 20:24:27 +0000 (15:24 -0500)]
USB: cp210x: add ID for RUGGEDCOM USB Serial Console

commit a6f0331236fa75afba14bbcf6668d42cebb55c43 upstream.

Added the USB serial console device ID for Siemens Ruggedcom devices
which have a USB port for their serial console.

Signed-off-by: Len Sorensen <>
Signed-off-by: Johan Hovold <>
Signed-off-by: Ben Hutchings <>
8 years agoPCI: Fix infinite loop with ROM image of size 0
Michel Dänzer [Mon, 19 Jan 2015 08:53:20 +0000 (17:53 +0900)]
PCI: Fix infinite loop with ROM image of size 0

commit 16b036af31e1456cb69243a5a0c9ef801ecd1f17 upstream.

If the image size would ever read as 0, pci_get_rom_size() could keep
processing the same image over and over again.  Exit the loop if we ever
read a length of zero.

This fixes a soft lockup on boot when the radeon driver calls
pci_get_rom_size() on an AMD Radeon R7 250X PCIe discrete graphics card.

[bhelgaas: changelog, reference]
Reported-by: Federico <>
Signed-off-by: Michel Dänzer <>
Signed-off-by: Bjorn Helgaas <>
Reviewed-by: Alex Deucher <>
Signed-off-by: Ben Hutchings <>
8 years agoKVM: s390: base hrtimer on a monotonic clock
David Hildenbrand [Fri, 12 Dec 2014 14:17:31 +0000 (15:17 +0100)]
KVM: s390: base hrtimer on a monotonic clock

commit 0ac96caf0f9381088c673a16d910b1d329670edf upstream.

The hrtimer that handles the wait with enabled timer interrupts
should not be disturbed by changes of the host time.

This patch changes our hrtimer to be based on a monotonic clock.

Signed-off-by: David Hildenbrand <>
Acked-by: Cornelia Huck <>
Signed-off-by: Christian Borntraeger <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agosmack: fix possible use after frees in task_security() callers
Andrey Ryabinin [Tue, 13 Jan 2015 15:52:40 +0000 (18:52 +0300)]
smack: fix possible use after frees in task_security() callers

commit 6d1cff2a885850b78b40c34777b46cf5da5d1050 upstream.

We hit use after free on dereferncing pointer to task_smack struct in
smk_of_task() called from smack_task_to_inode().

task_security() macro uses task_cred_xxx() to get pointer to the task_smack.
task_cred_xxx() could be used only for non-pointer members of task's
credentials. It cannot be used for pointer members since what they point
to may disapper after dropping RCU read lock.

Mainly task_security() used this way:

Intead of this introduce function smk_of_task_struct() which
takes task_struct as argument and returns pointer to smk_known struct
and do this under RCU read lock.
Bogus task_security() macro is not used anymore, so remove it.

KASan's report for this:

AddressSanitizer: use after free in smack_task_to_inode+0x50/0x70 at addr c4635600
BUG kmalloc-64 (Tainted: PO): kasan error

Disabling lock debugging due to kernel taint
INFO: Allocated in new_task_smack+0x44/0xd8 age=39 cpu=0 pid=1866
INFO: Freed in smack_cred_free+0xc4/0xd0 age=27 cpu=0 pid=1564
INFO: Slab 0xd3b23f50 objects=32 used=31 fp=0xc4635600 flags=0x4080
INFO: Object 0xc4635600 @offset=5632 fp=0x  (null)

Bytes b4 c46355f0: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a  ZZZZZZZZZZZZZZZZ
Object c4635600: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  kkkkkkkkkkkkkkkk
Object c4635610: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  kkkkkkkkkkkkkkkk
Object c4635620: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  kkkkkkkkkkkkkkkk
Object c4635630: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5  kkkkkkkkkkkkkkk.
Redzone c4635640: bb bb bb bb                                      ....
Padding c46356e8: 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a 5a  ZZZZZZZZZZZZZZZZ
Padding c46356f8: 5a 5a 5a 5a 5a 5a 5a 5a                          ZZZZZZZZ
CPU: 5 PID: 834 Comm: launchpad_prelo Tainted: PBO 3.10.30 #1
[<c00233a4>] (dump_backtrace+0x0/0x158) from [<c0023dec>] (show_stack+0x20/0x24)
 r7:c4634010 r6:d3b23f50 r5:c4635600 r4:d1002140
[<c0023dcc>] (show_stack+0x0/0x24) from [<c06d6d7c>] (dump_stack+0x20/0x28)
[<c06d6d5c>] (dump_stack+0x0/0x28) from [<c01c1d50>] (print_trailer+0x124/0x144)
[<c01c1c2c>] (print_trailer+0x0/0x144) from [<c01c1e88>] (object_err+0x3c/0x44)
 r7:c4635600 r6:d1002140 r5:d3b23f50 r4:c4635600
[<c01c1e4c>] (object_err+0x0/0x44) from [<c01cac18>] (kasan_report_error+0x2b8/0x538)
 r6:d1002140 r5:d3b23f50 r4:c6429cf8 r3:c09e1aa7
[<c01ca960>] (kasan_report_error+0x0/0x538) from [<c01c9430>] (__asan_load4+0xd4/0xf8)
[<c01c935c>] (__asan_load4+0x0/0xf8) from [<c031e168>] (smack_task_to_inode+0x50/0x70)
 r5:c4635600 r4:ca9da000
[<c031e118>] (smack_task_to_inode+0x0/0x70) from [<c031af64>] (security_task_to_inode+0x3c/0x44)
 r5:cca25e80 r4:c0ba9780
[<c031af28>] (security_task_to_inode+0x0/0x44) from [<c023d614>] (pid_revalidate+0x124/0x178)
 r6:00000000 r5:cca25e80 r4:cbabe3c0 r3:00008124
[<c023d4f0>] (pid_revalidate+0x0/0x178) from [<c01db98c>] (lookup_fast+0x35c/0x43y4)
 r9:c6429efc r8:00000101 r7:c079d940 r6:c6429e90 r5:c6429ed8 r4:c83c4148
[<c01db630>] (lookup_fast+0x0/0x434) from [<c01deec8>] (do_last.isra.24+0x1c0/0x1108)
[<c01ded08>] (do_last.isra.24+0x0/0x1108) from [<c01dff04>] (path_openat.isra.25+0xf4/0x648)
[<c01dfe10>] (path_openat.isra.25+0x0/0x648) from [<c01e1458>] (do_filp_open+0x3c/0x88)
[<c01e141c>] (do_filp_open+0x0/0x88) from [<c01ccb28>] (do_sys_open+0xf0/0x198)
 r7:00000001 r6:c0ea2180 r5:0000000b r4:00000000
[<c01cca38>] (do_sys_open+0x0/0x198) from [<c01ccc00>] (SyS_open+0x30/0x34)
[<c01ccbd0>] (SyS_open+0x0/0x34) from [<c001db80>] (ret_fast_syscall+0x0/0x48)
Read of size 4 by thread T834:
Memory state around the buggy address:
 c4635380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 c4635400: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
 c4635480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 c4635500: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc
 c4635580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>c4635600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 c4635680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
 c4635700: 00 00 00 00 04 fc fc fc fc fc fc fc fc fc fc fc
 c4635780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 c4635800: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
 c4635880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc

Signed-off-by: Andrey Ryabinin <>
[bwh: Backported to 3.2:
 - smk_of_task() and similar functions return char * not struct smack_known *
 - The callers of task_security() are quite different, but most can be changed
   to use smk_of_task_struct() just as in the upstream version
 - Use open-coded RCU locking in the one place using smk_of_forked() instead
   of smk_of_task()]
Signed-off-by: Ben Hutchings <>
8 years agoBluetooth: ath3k: Add support of AR3012 bluetooth 13d3:3423 device
Dmitry Tunin [Sat, 17 Jan 2015 21:16:51 +0000 (00:16 +0300)]
Bluetooth: ath3k: Add support of AR3012 bluetooth 13d3:3423 device

commit 033efa920a7f22a8caf7a38d851a2f451781bbf7 upstream.

Add support of 13d3:3423 device.

T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3423 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms

Signed-off-by: Dmitry Tunin <>
Signed-off-by: Marcel Holtmann <>
Signed-off-by: Ben Hutchings <>
8 years agoTPM: Add new TPMs to the tail of the list to prevent inadvertent change of dev
David Howells [Fri, 29 Aug 2014 09:33:02 +0000 (10:33 +0100)]
TPM: Add new TPMs to the tail of the list to prevent inadvertent change of dev

commit 398a1e71dc827b994b7f2f56c7c2186fea7f8d75 upstream.

Add newly registered TPMs to the tail of the list, not the beginning, so that
things that are specifying TPM_ANY_NUM don't find that the device they're
using has inadvertently changed.  Adding a second device would break IMA, for

Signed-off-by: David Howells <>
Reviewed-by: Jason Gunthorpe <>
Signed-off-by: Peter Huewe <>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <>
8 years agoaxonram: Fix bug in direct_access
Matthew Wilcox [Wed, 7 Jan 2015 16:04:18 +0000 (18:04 +0200)]
axonram: Fix bug in direct_access

commit 91117a20245b59f70b563523edbf998a62fc6383 upstream.

The 'pfn' returned by axonram was completely bogus, and has been since

Signed-off-by: Matthew Wilcox <>
Reviewed-by: Jan Kara <>
Reviewed-by: Mathieu Desnoyers <>
Signed-off-by: Jens Axboe <>
Signed-off-by: Ben Hutchings <>
8 years agousb: core: buffer: smallest buffer should start at ARCH_DMA_MINALIGN
Sebastian Andrzej Siewior [Fri, 5 Dec 2014 14:13:54 +0000 (15:13 +0100)]
usb: core: buffer: smallest buffer should start at ARCH_DMA_MINALIGN

commit 5efd2ea8c9f4f12916ffc8ba636792ce052f6911 upstream.

the following error pops up during "testusb -a -t 10"
| musb-hdrc dma_pool_free buffer-128, f134e000/be842000 (bad dma)
hcd_buffer_create() creates a few buffers, the smallest has 32 bytes of
size. ARCH_KMALLOC_MINALIGN is set to 64 bytes. This combo results in
hcd_buffer_alloc() returning memory which is 32 bytes aligned and it
might by identified by buffer_offset() as another buffer. This means the
buffer which is on a 32 byte boundary will not get freed, instead it
tries to free another buffer with the error message.

This patch fixes the issue by creating the smallest DMA buffer with the
smaller). This might be 32, 64 or even 128 bytes. The next three pools
will have the size 128, 512 and 2048.
In case the smallest pool is 128 bytes then we have only three pools
instead of four (and zero the first entry in the array).
The last pool size is always 2048 bytes which is the assumed PAGE_SIZE /
2 of 4096. I doubt it makes sense to continue using PAGE_SIZE / 2 where
we would end up with 8KiB buffer in case we have 16KiB pages.
Instead I think it makes sense to have a common size(s) and extend them
if there is need to.
There is a BUILD_BUG_ON() now in case someone has a minalign of more than
128 bytes.

Signed-off-by: Sebastian Andrzej Siewior <>
Acked-by: Alan Stern <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
8 years agokernel.h: add BUILD_BUG() macro
David Daney [Tue, 10 Jan 2012 23:07:25 +0000 (15:07 -0800)]
kernel.h: add BUILD_BUG() macro

commit 1399ff86f2a2bbacbbe68fa00c5f8c752b344723 upstream.

We can place this in definitions that we expect the compiler to remove by
dead code elimination.  If this assertion fails, we get a nice error
message at build time.

The GCC function attribute error("message") was added in version 4.3, so
we define a new macro __linktime_error(message) to expand to this for
GCC-4.3 and later.  This will give us an error diagnostic from the
compiler on the line that fails.  For other compilers
__linktime_error(message) expands to nothing, and we have to be content
with a link time error, but at least we will still get a build error.

BUILD_BUG() expands to the undefined function __build_bug_failed() and
will fail at link time if the compiler ever emits code for it.  On GCC-4.3
and later, attribute((error())) is used so that the failure will be noted
at compile time instead.

Signed-off-by: David Daney <>
Acked-by: David Rientjes <>
Cc: DM <>
Cc: Ralf Baechle <>
Acked-by: David Howells <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agoPCI: Generate uppercase hex for modalias var in uevent
Ricardo Ribalda Delgado [Tue, 2 Dec 2014 16:35:04 +0000 (17:35 +0100)]
PCI: Generate uppercase hex for modalias var in uevent

commit 145b3fe579db66fbe999a2bc3fd5b63dffe9636d upstream.

Some implementations of modprobe fail to load the driver for a PCI device
automatically because the "interface" part of the modalias from the kernel
is lowercase, and the modalias from file2alias is uppercase.

The "interface" is the low-order byte of the Class Code, defined in PCI
r3.0, Appendix D.  Most interface types defined in the spec do not use
alpha characters, so they won't be affected.  For example, 00h, 01h, 10h,
20h, etc. are unaffected.

Print the "interface" byte of the Class Code in uppercase hex, as we
already do for the Vendor ID, Device ID, Class, etc.

Commit 89ec3dcf17fd ("PCI: Generate uppercase hex for modalias interface
class") fixed only half of the problem.  Some udev implementations rely on
the uevent file and not the modalias file.

Fixes: d1ded203adf1 ("PCI: add MODALIAS to hotplug event for pci devices")
Fixes: 89ec3dcf17fd ("PCI: Generate uppercase hex for modalias interface class")
Signed-off-by: Ricardo Ribalda Delgado <>
Signed-off-by: Bjorn Helgaas <>
Acked-by: Greg Kroah-Hartman <>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <>
8 years agoudf: Check length of extended attributes and allocation descriptors
Jan Kara [Wed, 7 Jan 2015 12:49:08 +0000 (13:49 +0100)]
udf: Check length of extended attributes and allocation descriptors

commit 23b133bdc452aa441fcb9b82cbf6dd05cfd342d0 upstream.

Check length of extended attributes and allocation descriptors when
loading inodes from disk. Otherwise corrupted filesystems could confuse
the code and make the kernel oops.

Reported-by: Carl Henrik Lunde <>
Signed-off-by: Jan Kara <>
[bwh: Backported to 3.16: use make_bad_inode() instead of returning error]
Signed-off-by: Ben Hutchings <>
8 years agoudf: Remove repeated loads blocksize
Jan Kara [Wed, 7 Jan 2015 12:46:16 +0000 (13:46 +0100)]
udf: Remove repeated loads blocksize

commit 79144954278d4bb5989f8b903adcac7a20ff2a5a upstream.

Store blocksize in a local variable in udf_fill_inode() since it is used
a lot of times.

Signed-off-by: Jan Kara <>
[bwh: Needed for the following fix. Backported to 3.16: adjust context.]
Signed-off-by: Ben Hutchings <>
8 years agohx4700: regulator: declare full constraints
Martin Vajnar [Tue, 23 Dec 2014 23:27:57 +0000 (00:27 +0100)]
hx4700: regulator: declare full constraints

commit a52d209336f8fc7483a8c7f4a8a7d2a8e1692a6c upstream.

Since the removal of CONFIG_REGULATOR_DUMMY option, the touchscreen stopped
working. This patch enables the "replacement" for REGULATOR_DUMMY and
allows the touchscreen to work even though there is no regulator for "vcc".

Signed-off-by: Martin Vajnar <>
Signed-off-by: Robert Jarzmik <>
Signed-off-by: Ben Hutchings <>
8 years agoARM: pxa: add regulator_has_full_constraints to spitz board file
Dmitry Eremin-Solenikov [Thu, 4 Dec 2014 11:10:02 +0000 (14:10 +0300)]
ARM: pxa: add regulator_has_full_constraints to spitz board file

commit baad2dc49c5d970ea881d92981a1b76c94a7b7a1 upstream.

Add regulator_has_full_constraints() call to spitz board file to let
regulator core know that we do not have any additional regulators left.
This lets it substitute unprovided regulators with dummy ones.

This fixes the following warnings that can be seen on spitz if
regulators are enabled:

ads7846 spi2.0: unable to get regulator: -517
spi spi2.0: Driver ads7846 requests probe deferral

Signed-off-by: Dmitry Eremin-Solenikov <>
Acked-by: Mark Brown <>
Signed-off-by: Robert Jarzmik <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agoARM: pxa: add regulator_has_full_constraints to poodle board file
Dmitry Eremin-Solenikov [Thu, 4 Dec 2014 11:10:01 +0000 (14:10 +0300)]
ARM: pxa: add regulator_has_full_constraints to poodle board file

commit 9bc78f32c2e430aebf6def965b316aa95e37a20c upstream.

Add regulator_has_full_constraints() call to poodle board file to let
regulator core know that we do not have any additional regulators left.
This lets it substitute unprovided regulators with dummy ones.

This fixes the following warnings that can be seen on poodle if
regulators are enabled:

ads7846 spi1.0: unable to get regulator: -517
spi spi1.0: Driver ads7846 requests probe deferral
wm8731 0-001b: Failed to get supply 'AVDD': -517
wm8731 0-001b: Failed to request supplies: -517
wm8731 0-001b: ASoC: failed to probe component -517

Signed-off-by: Dmitry Eremin-Solenikov <>
Acked-by: Mark Brown <>
Signed-off-by: Robert Jarzmik <>
Signed-off-by: Ben Hutchings <>
8 years agoARM: pxa: add regulator_has_full_constraints to corgi board file
Dmitry Eremin-Solenikov [Thu, 4 Dec 2014 11:10:00 +0000 (14:10 +0300)]
ARM: pxa: add regulator_has_full_constraints to corgi board file

commit 271e80176aae4e5b481f4bb92df9768c6075bbca upstream.

Add regulator_has_full_constraints() call to corgi board file to let
regulator core know that we do not have any additional regulators left.
This lets it substitute unprovided regulators with dummy ones.

This fixes the following warnings that can be seen on corgi if
regulators are enabled:

ads7846 spi1.0: unable to get regulator: -517
spi spi1.0: Driver ads7846 requests probe deferral
wm8731 0-001b: Failed to get supply 'AVDD': -517
wm8731 0-001b: Failed to request supplies: -517
wm8731 0-001b: ASoC: failed to probe component -517
corgi-audio corgi-audio: ASoC: failed to instantiate card -517

Signed-off-by: Dmitry Eremin-Solenikov <>
Acked-by: Mark Brown <>
Signed-off-by: Robert Jarzmik <>
Signed-off-by: Ben Hutchings <>
8 years agoLinux 3.2.68 v3.2.68
Ben Hutchings [Fri, 6 Mar 2015 00:39:21 +0000 (00:39 +0000)]
Linux 3.2.68

8 years agoBluetooth: ath3k: workaround the compatibility issue with xHCI controller
Adam Lee [Wed, 28 Jan 2015 20:30:27 +0000 (15:30 -0500)]
Bluetooth: ath3k: workaround the compatibility issue with xHCI controller

commit c561a5753dd631920c4459a067d22679b3d110d6 upstream.

ath3k devices fail to load firmwares on xHCI buses, but work well on
EHCI, this might be a compatibility issue between xHCI and ath3k chips.
As my testing result, those chips will work on xHCI buses again with
this patch.

This workaround is from Qualcomm, they also did some workarounds in
Windows driver.

Signed-off-by: Adam Lee <>
Signed-off-by: Marcel Holtmann <>
Signed-off-by: Ben Hutchings <>
8 years agoipv6: fib: fix fib dump restart
Kumar Sundararajan [Thu, 24 Apr 2014 13:48:53 +0000 (09:48 -0400)]
ipv6: fib: fix fib dump restart

commit 1c2658545816088477e91860c3a645053719cb54 upstream.

When the ipv6 fib changes during a table dump, the walk is
restarted and the number of nodes dumped are skipped. But the existing
code doesn't advance to the next node after a node is skipped. This can
cause the dump to loop or produce lots of duplicates when the fib
is modified during the dump.

This change advances the walk to the next node if the current node is
skipped after a restart.

Signed-off-by: Kumar Sundararajan <>
Signed-off-by: Chris Mason <>
Signed-off-by: David S. Miller <>
Signed-off-by: Ben Hutchings <>
8 years agoipv6: fib: fix fib dump restart
Eric Dumazet [Mon, 25 Jun 2012 22:37:19 +0000 (15:37 -0700)]
ipv6: fib: fix fib dump restart

commit fa809e2fd6e317226c046202a88520962672eac0 upstream.

Commit 2bec5a369ee79576a3 (ipv6: fib: fix crash when changing large fib
while dumping it) introduced ability to restart the dump at tree root,
but failed to skip correctly a count of already dumped entries. Code
didn't match Patrick intent.

We must skip exactly the number of already dumped entries.

Note that like other /proc/net files or netlink producers, we could
still dump some duplicates entries.

Reported-by: Debabrata Banerjee <>
Reported-by: Josh Hunt <>
Signed-off-by: Eric Dumazet <>
Signed-off-by: David S. Miller <>
Signed-off-by: Ben Hutchings <>
8 years agontp: Fixup adjtimex freq validation on 32-bit systems
John Stultz [Tue, 10 Feb 2015 07:30:36 +0000 (23:30 -0800)]
ntp: Fixup adjtimex freq validation on 32-bit systems

commit 29183a70b0b828500816bd794b3fe192fce89f73 upstream.

Additional validation of adjtimex freq values to avoid
potential multiplication overflows were added in commit
5e5aeb4367b (time: adjtimex: Validate the ADJ_FREQUENCY values)

Unfortunately the patch used LONG_MAX/MIN instead of
LLONG_MAX/MIN, which was fine on 64-bit systems, but being
much smaller on 32-bit systems caused false positives
resulting in most direct frequency adjustments to fail w/

ntpd only does direct frequency adjustments at startup, so
the issue was not as easily observed there, but other time
sync applications like ptpd and chrony were more effected by
the bug.

See bugs:

This patch changes the checks to use LLONG_MAX for
clarity, and additionally the checks are disabled
on 32-bit systems since LLONG_MAX/PPM_SCALE is always
larger then the 32-bit long freq value, so multiplication
overflows aren't possible there.

Reported-by: Josh Boyer <>
Reported-by: George Joseph <>
Tested-by: George Joseph <>
Signed-off-by: John Stultz <>
Signed-off-by: Peter Zijlstra (Intel) <>
Cc: Linus Torvalds <>
Cc: Sasha Levin <>
[ Prettified the changelog and the comments a bit. ]
Signed-off-by: Ingo Molnar <>
Signed-off-by: Ben Hutchings <>
8 years agotime: adjtimex: Validate the ADJ_FREQUENCY values
Sasha Levin [Thu, 4 Dec 2014 00:25:05 +0000 (19:25 -0500)]
time: adjtimex: Validate the ADJ_FREQUENCY values

commit 5e5aeb4367b450a28f447f6d5ab57d8f2ab16a5f upstream.

Verify that the frequency value from userspace is valid and makes sense.

Unverified values can cause overflows later on.

Cc: Thomas Gleixner <>
Cc: Ingo Molnar <>
Signed-off-by: Sasha Levin <>
[jstultz: Fix up bug for negative values and drop redunent cap check]
Signed-off-by: John Stultz <>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <>
8 years agosched/rt: Reduce rq lock contention by eliminating locking of non-feasible target
Tim Chen [Fri, 12 Dec 2014 23:38:12 +0000 (15:38 -0800)]
sched/rt: Reduce rq lock contention by eliminating locking of non-feasible target

commit 80e3d87b2c5582db0ab5e39610ce3707d97ba409 upstream.

This patch adds checks that prevens futile attempts to move rt tasks
to a CPU with active tasks of equal or higher priority.

This reduces run queue lock contention and improves the performance of
a well known OLTP benchmark by 0.7%.

Signed-off-by: Tim Chen <>
Signed-off-by: Peter Zijlstra (Intel) <>
Cc: Shawn Bohrer <>
Cc: Suruchi Kadu <>
Cc: Doug Nelson<>
Cc: Steven Rostedt <>
Cc: Linus Torvalds <>
Signed-off-by: Ingo Molnar <>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <>
8 years agomedia/rc: Send sync space information on the lirc device
Austin Lund [Thu, 24 Jul 2014 10:40:20 +0000 (07:40 -0300)]
media/rc: Send sync space information on the lirc device

commit a8f29e89f2b54fbf2c52be341f149bc195b63a8b upstream.

Userspace expects to see a long space before the first pulse is sent on
the lirc device.  Currently, if a long time has passed and a new packet
is started, the lirc codec just returns and doesn't send anything.  This
makes lircd ignore many perfectly valid signals unless they are sent in
quick sucession.  When a reset event is delivered, we cannot know
anything about the duration of the space.  But it should be safe to
assume it has been a long time and we just set the duration to maximum.

Signed-off-by: Austin Lund <>
Signed-off-by: Mauro Carvalho Chehab <>
Signed-off-by: Ben Hutchings <>
8 years agostaging: comedi: cb_pcidas64: fix incorrect AI range code handling
Ian Abbott [Fri, 27 Feb 2015 18:52:08 +0000 (18:52 +0000)]
staging: comedi: cb_pcidas64: fix incorrect AI range code handling

commit be8e89087ec2d2c8a1ad1e3db64bf4efdfc3c298 upstream.

The hardware range code values and list of valid ranges for the AI
subdevice is incorrect for several supported boards.  The hardware range
code values for all boards except PCI-DAS4020/12 is determined by
calling `ai_range_bits_6xxx()` based on the maximum voltage of the range
and whether it is bipolar or unipolar, however it only returns the
correct hardware range code for the PCI-DAS60xx boards.  For
PCI-DAS6402/16 (and /12) it returns the wrong code for the unipolar
ranges.  For PCI-DAS64/Mx/16 it returns the wrong code for all the
ranges and the comedi range table is incorrect.

Change `ai_range_bits_6xxx()` to use a look-up table pointed to by new
member `ai_range_codes` of `struct pcidas64_board` to map the comedi
range table indices to the hardware range codes.  Use a new comedi range
table for the PCI-DAS64/Mx/16 boards (and the commented out variants).

Signed-off-by: Ian Abbott <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
8 years agoDrivers: hv: vmbus: incorrect device name is printed when child device is unregistered
Fernando Soto [Fri, 14 Jun 2013 23:13:35 +0000 (23:13 +0000)]
Drivers: hv: vmbus: incorrect device name is printed when child device is unregistered

commit 84672369ffb98a51d4ddf74c20a23636da3ad615 upstream.

Whenever a device is unregistered in vmbus_device_unregister (drivers/hv/vmbus_drv.c), the device name in the log message may contain garbage as the memory has already been freed by the time pr_info is called. Log example:
 [ 3149.170475] hv_vmbus: child device àõsèè0_5 unregistered

By logging the message just before calling device_unregister, the correct device name is printed:
[ 3145.034652] hv_vmbus: child device vmbus_0_5 unregistered

Also changing register & unregister messages to debug to avoid unnecessarily cluttering the kernel log.

Signed-off-by: Fernando M Soto <>
Signed-off-by: K. Y. Srinivasan <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Ben Hutchings <>
8 years agonilfs2: fix deadlock of segment constructor over I_SYNC flag
Ryusuke Konishi [Thu, 5 Feb 2015 20:25:20 +0000 (12:25 -0800)]
nilfs2: fix deadlock of segment constructor over I_SYNC flag

commit 7ef3ff2fea8bf5e4a21cef47ad87710a3d0fdb52 upstream.

Nilfs2 eventually hangs in a stress test with fsstress program.  This
issue was caused by the following deadlock over I_SYNC flag between
nilfs_segctor_thread() and writeback_sb_inodes():

                inode_wait_for_writeback()  * wait for I_SYNC flag

     * set I_SYNC flag on inode->i_state
               * wait for completion of segment constructor
       * clear I_SYNC flag after __writeback_single_inode() completed

writeback_sb_inodes() calls do_writepages() for dirty inodes after
setting I_SYNC flag on inode->i_state.  do_writepages() in turn calls
nilfs_writepages(), which can run segment constructor and wait for its
completion.  On the other hand, segment constructor calls iput(), which
can call evict() and wait for the I_SYNC flag on

Since segment constructor doesn't know when I_SYNC will be set, it
cannot know whether iput() will block or not unless inode->i_nlink has a
non-zero count.  We can prevent evict() from being called in iput() by
implementing sop->drop_inode(), but it's not preferable to leave inodes
with i_nlink == 0 for long periods because it even defers file
truncation and inode deallocation.  So, this instead resolves the
deadlock by calling iput() asynchronously with a workqueue for inodes
with i_nlink == 0.

Signed-off-by: Ryusuke Konishi <>
Cc: Al Viro <>
Tested-by: Ryusuke Konishi <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
8 years agomm: pagewalk: call pte_hole() for VM_PFNMAP during walk_page_range
Shiraz Hashim [Thu, 5 Feb 2015 20:25:06 +0000 (12:25 -0800)]
mm: pagewalk: call pte_hole() for VM_PFNMAP during walk_page_range

commit 23aaed6659df9adfabe9c583e67a36b54e21df46 upstream.

walk_page_range() silently skips vma having VM_PFNMAP set, which leads
to undesirable behaviour at client end (who called walk_page_range).
Userspace applications get the wrong data, so the effect is like just
confusing users (if the applications just display the data) or sometimes
killing the processes (if the applications do something with
misunderstanding virtual addresses due to the wrong data.)

For example for pagemap_read, when no callbacks are called against
VM_PFNMAP vma, pagemap_read may prepare pagemap data for next virtual
address range at wrong index.

Eventually userspace may get wrong pagemap data for a task.
Corresponding to a VM_PFNMAP marked vma region, kernel may report
mappings from subsequent vma regions.  User space in turn may account
more pages (than really are) to the task.

In my case I was using procmem, procrack (Android utility) which uses
pagemap interface to account RSS pages of a task.  Due to this bug it
was giving a wrong picture for vmas (with VM_PFNMAP set).

Fixes: a9ff785e4437 ("mm/pagewalk.c: walk_page_range should avoid VM_PFNMAP areas")
Signed-off-by: Shiraz Hashim <>
Acked-by: Naoya Horiguchi <>
Signed-off-by: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Ben Hutchings <>
8 years agonet: sctp: fix passing wrong parameter header to param_type2af in sctp_process_param
Saran Maruti Ramanara [Thu, 29 Jan 2015 10:05:58 +0000 (11:05 +0100)]
net: sctp: fix passing wrong parameter header to param_type2af in sctp_process_param

commit cfbf654efc6d78dc9812e030673b86f235bf677d upstream.

When making use of RFC5061, section 4.2.4. for setting the primary IP
address, we're passing a wrong parameter header to param_type2af(),
resulting always in NULL being returned.

At this point, param.p points to a sctp_addip_param struct, containing
a sctp_paramhdr (type = 0xc004, length = var), and crr_id as a correlation
id. Followed by that, as also presented in RFC5061 section 4.2.4., comes
the actual sctp_addr_param, which also contains a sctp_paramhdr, but
this time with the correct type SCTP_PARAM_IPV{4,6}_ADDRESS that
param_type2af() can make use of. Since we already hold a pointer to
addr_param from previous line, just reuse it for param_type2af().

Fixes: d6de3097592b ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Saran Maruti Ramanara <>
Signed-off-by: Daniel Borkmann <>
Acked-by: Vlad Yasevich <>
Acked-by: Neil Horman <>
Signed-off-by: David S. Miller <>
Signed-off-by: Ben Hutchings <>
8 years agogpio: sysfs: fix memory leak in gpiod_sysfs_set_active_low
Johan Hovold [Mon, 26 Jan 2015 11:02:46 +0000 (12:02 +0100)]
gpio: sysfs: fix memory leak in gpiod_sysfs_set_active_low

commit 49d2ca84e433dab854c7a866bc6add09cfab682d upstream.

Fix memory leak in the gpio sysfs interface due to failure to drop
reference to device returned by class_find_device when setting the
gpio-line polarity.

Fixes: 0769746183ca ("gpiolib: add support for changing value polarity
in sysfs")
Signed-off-by: Johan Hovold <>
Signed-off-by: Linus Walleij <>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <>
8 years agogpio: sysfs: fix memory leak in gpiod_export_link
Johan Hovold [Mon, 26 Jan 2015 11:02:45 +0000 (12:02 +0100)]
gpio: sysfs: fix memory leak in gpiod_export_link

commit 0f303db08df0df9bd0966443ad6001e63960af16 upstream.

Fix memory leak in the gpio sysfs interface due to failure to drop
reference to device returned by class_find_device when creating a link.

Fixes: a4177ee7f1a8 ("gpiolib: allow exported GPIO nodes to be named
using sysfs links")
Signed-off-by: Johan Hovold <>
Signed-off-by: Linus Walleij <>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <>