Bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=105331
reports that the "AEO model 0" display is driven with 8 bpc
without dithering by default, which looks bad because that
panel is apparently a 6 bpc DP panel with faulty EDID.
A fix for this was made by commit 013dd9e03872
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown").
That commit triggers new regressions in precision for DP->DVI and
DP->VGA displays. A patch is out to revert that commit, but it will
revert video output for the AEO model 0 panel to 8 bpc without
dithering.
The EDID 1.3 of that panel, as decoded from the xrandr output
attached to that bugzilla bug report, is somewhat faulty, and beyond
other problems also sets the "DFP 1.x compliant TMDS" bit, which
according to DFP spec means to drive the panel with 8 bpc and
no dithering in absence of other colorimetry information.
Try to make the original bug reporter happy despite the
faulty EDID by adding a quirk to mark that panel as 6 bpc,
so 6 bpc output with dithering creates a nice picture.
Tested by injecting the edid from the fdo bug into a DP connector
via drm_kms_helper.edid_firmware and verifying the 6 bpc + dithering
is selected.
This patch should be backported to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Dave Airlie <airlied@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
BCM20706V2_EVAL is a WICED dev board designed with FT2232H USB 2.0
UART/FIFO IC.
To support BCM920706V2_EVAL dev board for WICED development on Linux.
Add the VID(0a5c) and PID(6422) to ftdi_sio driver to allow loading
ftdi_sio for this board.
Signed-off-by: Sheng-Hui J. Chu <s.jeffrey.chu@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This problem can occur in the following situation:
open()
- pread()
- .seq_start()
- iter = kmalloc() // succeeds
- seqf->private = iter
- .seq_stop()
- kfree(seqf->private)
- pread()
- .seq_start()
- iter = kmalloc() // fails
- .seq_stop()
- class_dev_iter_exit(seqf->private) // boom! old pointer
As the comment in disk_seqf_stop() says, stop is called even if start
failed, so we need to reinitialise the private pointer to NULL when seq
iteration stops.
An alternative would be to set the private pointer to NULL when the
kmalloc() in disk_seqf_start() fails.
We can't pass error pointers to kfree() or it causes an oops.
Fixes: 52b209f7b848 ('get rid of hostfs_read_inode()') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In powerpc servers with large memory(32TB), we watched several soft
lockups for hugepage under stress tests.
The call traces are as follows:
1.
get_page_from_freelist+0x2d8/0xd50
__alloc_pages_nodemask+0x180/0xc20
alloc_fresh_huge_page+0xb0/0x190
set_max_huge_pages+0x164/0x3b0
When the corrupt_bio_byte feature was introduced it caused READ bios to
no longer be errored with -EIO during the down_interval. This had to do
with the complexity of needing to submit READs if the corrupt_bio_byte
feature was used.
Fix it so READ bios are properly errored with -EIO; doing so early in
flakey_map() as long as there isn't a match for the corrupt_bio_byte
feature.
Fixes: a3998799fb4df ("dm flakey: add corrupt_bio_byte feature") Reported-by: Akira Hayakawa <ruby.wktk@gmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[bwh: Backported to 3.2: in flakey_end_io(), keep using
bio_submitted_while_down instead of pb->bio_submitted] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The balloon has a special mechanism that is subscribed to the oom
notification which leads to deflation for a fixed number of pages.
The number is always fixed even when the balloon is fully deflated.
But leak_balloon did not expect that the pages to deflate will be more
than taken, and raise a "BUG" in balloon_page_dequeue when page list
will be empty.
So, the simplest solution would be to check that the number of releases
pages is less or equal to the number taken pages.
Signed-off-by: Konstantin Neumoin <kneumoin@virtuozzo.com> Signed-off-by: Denis V. Lunev <den@openvz.org> CC: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
x86_64 needs to use compat_sys_keyctl for 32-bit userspace rather than
calling sys_keyctl(). The latter will work in a lot of cases, thereby
hiding the issue.
Reported-by: Stephan Mueller <smueller@chronox.de> Tested-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: David Howells <dhowells@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: keyrings@vger.kernel.org Cc: linux-security-module@vger.kernel.org Link: http://lkml.kernel.org/r/146961615805.14395.5581949237156769439.stgit@warthog.procyon.org.uk Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: compat system call table is in ia32entry.S] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
AT_VECTOR_SIZE_ARCH should be defined with the maximum number of
NEW_AUX_ENT entries that ARCH_DLINFO can contain, but it wasn't defined
for s390 at all even though ARCH_DLINFO can contain one NEW_AUX_ENT when
VDSO is enabled.
This shouldn't be a problem as AT_VECTOR_SIZE_BASE includes space for
AT_BASE_PLATFORM which s390 doesn't use, but lets define it now and add
the comment above ARCH_DLINFO as found in several other architectures to
remind future modifiers of ARCH_DLINFO to keep AT_VECTOR_SIZE_ARCH up to
date.
Fixes: b020632e40c3 ("[S390] introduce vdso on s390") Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: linux-s390@vger.kernel.org
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
tcp_select_initial_window() intends to advertise a window
scaling for the maximum possible window size. To do so,
it considers the maximum of net.ipv4.tcp_rmem[2] and
net.core.rmem_max as the only possible upper-bounds.
However, users with CAP_NET_ADMIN can use SO_RCVBUFFORCE
to set the socket's receive buffer size to values
larger than net.ipv4.tcp_rmem[2] and net.core.rmem_max.
Thus, SO_RCVBUFFORCE is effectively ignored by
tcp_select_initial_window().
To fix this, consider the maximum of net.ipv4.tcp_rmem[2],
net.core.rmem_max and socket's initial buffer space.
Fixes: b0573dea1fb3 ("[NET]: Introduce SO_{SND,RCV}BUFFORCE socket options") Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Suggested-by: Neal Cardwell <ncardwell@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
MIPS64 needs to use compat_sys_keyctl for 32-bit userspace rather than
calling sys_keyctl. The latter will work in a lot of cases, thereby hiding
the issue.
Reported-by: Stephan Mueller <smueller@chronox.de> Signed-off-by: David Howells <dhowells@redhat.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: linux-security-module@vger.kernel.org Cc: keyrings@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13832/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ceph_llseek does not correctly return NXIO errors because the 'out' path
always returns 'offset'.
Fixes: 06222e491e66 ("fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: Yan, Zheng <zyan@redhat.com>
[bwh: Backported to 3.2:
- We don't use vfs_setpos(); instead set ret = -EINVAL or ret = offset
directly
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As explained in 1407814240-4275-1-git-send-email-decui@microsoft.com we
have a hard load dependency between i8042 and atkbd which prevents
keyboard from working on Gen2 Hyper-V VMs.
> hyperv_keyboard invokes serio_interrupt(), which needs a valid serio
> driver like atkbd.c. atkbd.c depends on libps2.c because it invokes
> ps2_command(). libps2.c depends on i8042.c because it invokes
> i8042_check_port_owner(). As a result, hyperv_keyboard actually
> depends on i8042.c.
>
> For a Generation 2 Hyper-V VM (meaning no i8042 device emulated), if a
> Linux VM (like Arch Linux) happens to configure CONFIG_SERIO_I8042=m
> rather than =y, atkbd.ko can't load because i8042.ko can't load(due to
> no i8042 device emulated) and finally hyperv_keyboard can't work and
> the user can't input: https://bugs.archlinux.org/task/39820
> (Ubuntu/RHEL/SUSE aren't affected since they use CONFIG_SERIO_I8042=y)
To break the dependency we move away from using i8042_check_port_owner()
and instead allow serio port owner specify a mutex that clients should use
to serialize PS/2 command stream.
Reported-by: Mark Laws <mdl@60hz.org> Tested-by: Mark Laws <mdl@60hz.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If 'tunnel' is NULL we should return -EBADF but the 'end_put_sess' path
unconditionally sets 'error' back to zero. Rework the error path so it
more closely matches pppol2tp_sendmsg.
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The problem is that irda_open_tsap() can fail and leave self->tsap = NULL,
and then irttp_connect_request() almost immediately dereferences it.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
NFS doesn't expect requests with wb_bytes set to zero and may make
unexpected decisions about how to handle that request at the page IO layer.
Skip request creation if we won't have any wb_bytes in the request.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Reviewed-by: Weston Andros Adamson <dros@primarydata.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The size of individual keymap in drivers/tty/vt/keyboard.c is NR_KEYS,
which is currently 256, whereas number of keys/buttons in input device (and
therefor in key_down) is much larger - KEY_CNT - 768, and that can cause
out-of-bound access when we do
sym = U(key_maps[0][k]);
with large 'k'.
To fix it we should not attempt iterating beyond smaller of NR_KEYS and
KEY_CNT.
Also while at it let's switch to for_each_set_bit() instead of open-coding
it.
According to the datasheet you should only write 1 to this bit. If it is
not set, at least AIN3 will return bad values on newer silicon revisions.
Fixes: d84ca5b345c2 ("hwmon: Add driver for ADT7411 voltage and temperature sensor") Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write,
although it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating endlessly.
The bug may not be easy to reproduce in Linux since user space tools
usually force the padding or round-up the write size to a page-size
multiple.
This was discovered in U-Boot where the issue can be reproduced by
writing any size that is 1 byte less than a page-size multiple.
For example, on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
[Editor's note: the bug was added in commit 29072b96078f, but moved
around in commit 66507c7bc8895 ("mtd: nand: Add support to use nand_base
poi databuf as bounce buffer")]
Fixes: 29072b96078f ("[MTD] NAND: add subpage write support") Signed-off-by: Hector Palacios <hector.palacios@digi.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[bwh: Backported to 3.2: adjusted context as noted above] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
wlc_phy_txpower_get_current() does a logical OR of power->flags, which
presumes that power.flags was initiliazed earlier by the caller,
unfortunately, this is not the case, so make sure we zero out the struct
tx_power before calling into wlc_phy_txpower_get_current().
Reported-by: coverity (CID 146011) Fixes: 5b435de0d7868 ("net: wireless: add brcm80211 drivers") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some chips incorrectly support partial reads from TPM_STS register
at non-zero offsets. Read the entire 32-bits register instead of
making two 8-bit reads to support such devices and reduce the number
of bus transactions when obtaining the burstcount from TPM_STS.
Fixes: 27084efee0c3 ("tpm: driver for next generation TPM chips") Signed-off-by: Andrey Pronin <apronin@chromium.org> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
[bwh: Backported to 3.2:
- Use raw ioread32() instead of tpm_tis_read32()
- Adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When there is more data to be processed, the current test in
scatterwalk_done may prevent us from calling pagedone even when
we should.
In particular, if we're on an SG entry spanning multiple pages
where the last page is not a full page, we will incorrectly skip
calling pagedone on the second last page.
This patch fixes this by adding a separate test for whether we've
reached the end of a page.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When we retrieve imtu value from userspace we should use 16 bit pointer
cast instead of 32 as it's defined that way in headers. Fixes setsockopt
calls on big-endian platforms.
There is a cut and paste issue here. The bug is that we are allocating
more memory than necessary for msp_maps. We should be allocating enough
space for a map_info struct (144 bytes) but we instead allocate enough
for an mtd_info struct (1840 bytes). It's a small waste.
The other part of this is not harmful but when we allocated msp_flash
then we allocated enough space fro a map_info pointer instead of an
mtd_info pointer. But since pointers are the same size it works out
fine.
Anyway, I decided to clean up all three allocations a bit to make them
a bit more consistent and clear.
Fixes: 68aa0fa87f6d ('[MTD] PMC MSP71xx flash/rootfs mappings') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If we encounter a filesystem error during orphan cleanup, we should stop.
Otherwise, we may end up in an infinite loop where the same inode is
processed again and again.
EXT4-fs (loop0): warning: checktime reached, running e2fsck is recommended
EXT4-fs error (device loop0): ext4_mb_generate_buddy:758: group 2, block bitmap and bg descriptor inconsistent: 6117 vs 0 free clusters
Aborting journal on device loop0-8.
EXT4-fs (loop0): Remounting filesystem read-only
EXT4-fs error (device loop0) in ext4_free_blocks:4895: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs error (device loop0) in ext4_ext_remove_space:3068: IO failure
EXT4-fs error (device loop0) in ext4_ext_truncate:4667: Journal has aborted
EXT4-fs error (device loop0) in ext4_orphan_del:2927: Journal has aborted
EXT4-fs error (device loop0) in ext4_do_update_inode:4893: Journal has aborted
EXT4-fs (loop0): Inode 16 (00000000618192a0): orphan list check failed!
[...]
EXT4-fs (loop0): Inode 16 (0000000061819748): orphan list check failed!
[...]
EXT4-fs (loop0): Inode 16 (0000000061819bf0): orphan list check failed!
[...]
See-also: c9eb13a9105 ("ext4: fix hang when processing corrupted orphaned inode list") Cc: Jan Kara <jack@suse.cz> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If we hit this error when mounted with errors=continue or
errors=remount-ro:
EXT4-fs error (device loop0): ext4_mb_mark_diskspace_used:2940: comm ext4.exe: Allocating blocks 5090-6081 which overlap fs metadata
then ext4_mb_new_blocks() will call ext4_mb_release_context() and try to
continue. However, ext4_mb_release_context() is the wrong thing to call
here since we are still actually using the allocation context.
Instead, just error out. We could retry the allocation, but there is a
possibility of getting stuck in an infinite loop instead, so this seems
safer.
[ Fixed up so we don't return EAGAIN to userspace. --tytso ]
Fixes: 8556e8f3b6 ("ext4: Don't allow new groups to be added during block allocation") Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[bwh: Backported to 3.2:
- Use EIO instead of EFSCORRUPTED
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When freeing the nested resources of a vcpu, there is an assumption that
the vcpu's vmcs01 is the current VMCS on the CPU that executes
nested_release_vmcs12(). If this assumption is violated, the vcpu's
vmcs01 may be made active on multiple CPUs at the same time, in
violation of Intel's specification. Moreover, since the vcpu's vmcs01 is
not VMCLEARed on every CPU on which it is active, it can linger in a
CPU's VMCS cache after it has been freed and potentially
repurposed. Subsequent eviction from the CPU's VMCS cache on a capacity
miss can result in memory corruption.
It is not sufficient for vmx_free_vcpu() to call vmx_load_vmcs01(). If
the vcpu in question was last loaded on a different CPU, it must be
migrated to the current CPU before calling vmx_load_vmcs01().
Signed-off-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.2: vcpu_load() returns void] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
free_nested needs the loaded_vmcs to be valid if it is a vmcs02, in
order to detach it from the shadow vmcs. However, this is not
available anymore after commit 26a865f4aa8e (KVM: VMX: fix use after
free of vmx->loaded_vmcs, 2014-01-03).
Revert that patch, and fix its problem by forcing a vmcs01 as the
active VMCS before freeing all the nested VMX state.
Reported-by: Wanpeng Li <wanpeng.li@linux.intel.com> Tested-by: Wanpeng Li <wanpeng.li@linux.intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In case any operation fails before we can successfully go the point
where we would register a MDIO bus, we would be going to an error label
which involves unregistering then freeing this yet to be created MDIO
bus. Update all error paths to go to label free which is the only one
valid until either the clock is enabled, or the MDIO bus is allocated
and registered. This fixes kernel oops observed while trying to
dereference the MDIO bus structure which is not yet allocated.
Fixes: a1702857724f ("net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Before commit 778be232a207 ("NFS do not find client in NFSv4
pg_authenticate"), the Linux callback server replied with
RPC_AUTH_ERROR / RPC_AUTH_BADCRED, instead of dropping the CB
request. Let's restore that behavior so the server has a chance to
do something useful about it, and provide a warning that helps
admins correct the problem.
Fixes: 778be232a207 ("NFS do not find client in NFSv4 ...") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Tested-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If an RPC program does not set vs_dispatch and pc_func() returns
rpc_drop_reply, the server sends a reply anyway containing a single
word containing the value RPC_DROP_REPLY (in network byte-order, of
course). This is a nonsense RPC message.
Fixes: 9e701c610923 ("svcrpc: simpler request dropping") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Tested-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The EFI firmware on Macs contains a full-fledged network stack for
downloading OS X images from osrecovery.apple.com. Unfortunately
on Macs introduced 2011 and 2012, EFI brings up the Broadcom 4331
wireless card on every boot and leaves it enabled even after
ExitBootServices has been called. The card continues to assert its IRQ
line, causing spurious interrupts if the IRQ is shared. It also corrupts
memory by DMAing received packets, allowing for remote code execution
over the air. This only stops when a driver is loaded for the wireless
card, which may be never if the driver is not installed or blacklisted.
The issue seems to be constrained to the Broadcom 4331. Chris Milsted
has verified that the newer Broadcom 4360 built into the MacBookPro11,3
(2013/2014) does not exhibit this behaviour. The chances that Apple will
ever supply a firmware fix for the older machines appear to be zero.
The solution is to reset the card on boot by writing to a reset bit in
its mmio space. This must be done as an early quirk and not as a plain
vanilla PCI quirk to successfully combat memory corruption by DMAed
packets: Matthew Garrett found out in 2012 that the packets are written
to EfiBootServicesData memory (http://mjg59.dreamwidth.org/11235.html).
This type of memory is made available to the page allocator by
efi_free_boot_services(). Plain vanilla PCI quirks run much later, in
subsys initcall level. In-between a time window would be open for memory
corruption. Random crashes occurring in this time window and attributed
to DMAed packets have indeed been observed in the wild by Chris
Bainbridge.
When Matthew Garrett analyzed the memory corruption issue in 2012, he
sought to fix it with a grub quirk which transitions the card to D3hot:
http://git.savannah.gnu.org/cgit/grub.git/commit/?id=9d34bb85da56
This approach does not help users with other bootloaders and while it
may prevent DMAed packets, it does not cure the spurious interrupts
emanating from the card. Unfortunately the card's mmio space is
inaccessible in D3hot, so to reset it, we have to undo the effect of
Matthew's grub patch and transition the card back to D0.
Note that the quirk takes a few shortcuts to reduce the amount of code:
The size of BAR 0 and the location of the PM capability is identical
on all affected machines and therefore hardcoded. Only the address of
BAR 0 differs between models. Also, it is assumed that the BCMA core
currently mapped is the 802.11 core. The EFI driver seems to always take
care of this.
Michael Büsch, Bjorn Helgaas and Matt Fleming contributed feedback
towards finding the best solution to this problem.
The following should be a comprehensive list of affected models:
iMac13,1 2012 21.5" [Root Port 00:1c.3 = 8086:1e16]
iMac13,2 2012 27" [Root Port 00:1c.3 = 8086:1e16]
Macmini5,1 2011 i5 2.3 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,2 2011 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,3 2011 i7 2.0 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini6,1 2012 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1e12]
Macmini6,2 2012 i7 2.3 GHz [Root Port 00:1c.1 = 8086:1e12]
MacBookPro8,1 2011 13" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,2 2011 15" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,3 2011 17" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro9,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro9,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
For posterity, spurious interrupts caused by the Broadcom 4331 wireless
card resulted in splats like this (stacktrace omitted):
We used to scan secondary buses until the following commit that
was applied in 2009:
8659c406ade3 ("x86: only scan the root bus in early PCI quirks")
which commit constrained early quirks to the root bus only. Its
motivation was to prevent application of the nvidia_bugs quirk
on secondary buses.
We're about to add a quirk to reset the Broadcom 4331 wireless card on
2011/2012 Macs, which is located on a secondary bus behind a PCIe root
port. To facilitate that, reintroduce scanning of secondary buses.
The commit message of 8659c406ade3 notes that scanning only the root bus
"saves quite some unnecessary scanning work". The algorithm used prior
to 8659c406ade3 was particularly time consuming because it scanned
buses 0 to 31 brute force. To avoid lengthening boot time, employ a
recursive strategy which only scans buses that are actually reachable
from the root bus.
Yinghai Lu pointed out that the secondary bus number read from a
bridge's config space may be invalid, in particular a value of 0 would
cause an infinite loop. The PCI core goes beyond that and recurses to a
child bus only if its bus number is greater than the parent bus number
(see pci_scan_bridge()). Since the root bus is numbered 0, this implies
that secondary buses may not be 0. Do the same on early scanning.
If this algorithm is found to significantly impact boot time or cause
infinite loops on broken hardware, it would be possible to limit its
recursion depth: The Broadcom 4331 quirk applies at depth 1, all others
at depth 0, so the bus need not be scanned deeper than that for now. An
alternative approach would be to revert to scanning only the root bus,
and apply the Broadcom 4331 quirk to the root ports 8086:1c12, 8086:1e12
and 8086:1e16. Apple always positioned the card behind either of these
three ports. The quirk would then check presence of the card in slot 0
below the root port and do its deed.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yinghai Lu <yinghai@kernel.org> Cc: linux-pci@vger.kernel.org Link: http://lkml.kernel.org/r/f0daa70dac1a9b2483abdb31887173eb6ab77bdf.1465690253.git.lukas@wunner.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
8659c406ade3 ("x86: only scan the root bus in early PCI quirks")
... early quirks are only applied to devices on the root bus.
The motivation was to prevent application of the nvidia_bugs quirk on
secondary buses.
We're about to reintroduce scanning of secondary buses for a quirk to
reset the Broadcom 4331 wireless card on 2011/2012 Macs. To prevent
regressions, open code the requirement to apply nvidia_bugs only on the
root bus.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yinghai Lu <yinghai@kernel.org> Link: http://lkml.kernel.org/r/4d5477c1d76b2f0387a780f2142bbcdd9fee869b.1465690253.git.lukas@wunner.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Matt reported that we have a NULL pointer dereference
in ppp_pernet() from ppp_connect_channel(),
i.e. pch->chan_net is NULL.
This is due to that a parallel ppp_unregister_channel()
could happen while we are in ppp_connect_channel(), during
which pch->chan_net set to NULL. Since we need a reference
to net per channel, it makes sense to sync the refcnt
with the life time of the channel, therefore we should
release this reference when we destroy it.
Fixes: 1f461dcdd296 ("ppp: take reference on channels netns") Reported-by: Matt Bennett <Matt.Bennett@alliedtelesis.co.nz> Cc: Paul Mackerras <paulus@samba.org> Cc: linux-ppp@vger.kernel.org Cc: Guillaume Nault <g.nault@alphalink.fr> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
snd_ctl_remove() has a notification for the removal event. It's
superfluous when done during the device got disconnected. Although
the notification itself is mostly harmless, it may potentially be
harmful, and should be suppressed. Actually some components PCM may
free ctl elements during the disconnect or free callbacks, thus it's
no theoretical issue.
This patch adds the check of card->shutdown flag for avoiding
unnecessary notifications after (or during) the disconnect.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
DRM_CONNECTOR_POLL_CONNECT only enables polling for connections, not
disconnections. Because of this, we end up losing hotplug polling for
analog connectors once they get connected.
Easy way to reproduce:
- Grab a machine with a radeon GPU and a VGA port
- Plug a monitor into the VGA port, wait for it to update the connector
from disconnected to connected
- Disconnect the monitor on VGA, a hotplug event is never sent for the
removal of the connector.
Originally, only using DRM_CONNECTOR_POLL_CONNECT might have been a good
idea since doing VGA polling can sometimes result in having to mess with
the DAC voltages to figure out whether or not there's actually something
there since VGA doesn't have HPD. Doing this would have the potential of
showing visible artifacts on the screen every time we ran a poll while a
VGA display was connected. Luckily, radeon_vga_detect() only resorts to
this sort of polling if the poll is forced, and DRM's polling helper
doesn't force it's polls.
Additionally, this removes some assignments to connector->polled that
weren't actually doing anything.
Signed-off-by: Lyude <cpaul@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If s_reserved_gdt_blocks is extremely large, it's possible for
ext4_init_block_bitmap(), which is called when ext4 sets up an
uninitialized block bitmap, to corrupt random kernel memory. Add the
same checks which e2fsck has --- it must never be larger than
blocksize / sizeof(__u32) --- and then add a backup check in
ext4_init_block_bitmap() in case the superblock gets modified after
the file system is mounted.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 3.2:
- Drop the second check in ext4_init_block_bitmap() since it can't return
an error code
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If ext4_fill_super() fails early, it's possible for ext4_evict_inode()
to call ext4_should_journal_data() before superblock options and flags
are fully set up. In that case, the iput() on the journal inode can
end up causing a BUG().
Work around this problem by reordering the tests so we only call
ext4_should_journal_data() after we know it's not the journal inode.
Fixes: 2d859db3e4 ("ext4: fix data corruption in inodes with journalled data") Fixes: 2b405bfa84 ("ext4: fix data=journal fast mount/umount hang") Cc: Jan Kara <jack@suse.cz> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
An extent with lblock = 4294967295 and len = 1 will pass the
ext4_valid_extent() test:
ext4_lblk_t last = lblock + len - 1;
if (len == 0 || lblock > last)
return 0;
since last = 4294967295 + 1 - 1 = 4294967295. This would later trigger
the BUG_ON(es->es_lblk + es->es_len < es->es_lblk) in ext4_es_end().
We can simplify it by removing the - 1 altogether and changing the test
to use lblock + len <= lblock, since now if len = 0, then lblock + 0 ==
lblock and it fails, and if len > 0 then lblock + len > lblock in order
to pass (i.e. it doesn't overflow).
Fixes: 5946d0893 ("ext4: check for overlapping extents in ext4_valid_extent_entries()") Fixes: 2f974865f ("ext4: check for zero length extent explicitly") Cc: Eryu Guan <guaneryu@gmail.com> Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes an issue that the CFIFOSEL register value is possible
to be changed by usbhsg_ep_enable() wrongly. And then, a data transfer
using CFIFO may not work correctly.
For example:
# modprobe g_multi file=usb-storage.bin
# ifconfig usb0 192.168.1.1 up
(During the USB host is sending file to the mass storage)
# ifconfig usb0 down
In this case, since the u_ether.c may call usb_ep_enable() in
eth_stop(), if the renesas_usbhs driver is also using CFIFO for
mass storage, the mass storage may not work correctly.
So, this patch adds usbhs_lock() and usbhs_unlock() calling in
usbhsg_ep_enable() to protect CFIFOSEL register. This is because:
- CFIFOSEL.CURPIPE = 0 is also needed for the pipe configuration
- The CFIFOSEL (fifo->sel) is already protected by usbhs_lock()
Fixes: 97664a207bc2 ("usb: renesas_usbhs: shrink spin lock area") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes an issue that the xfer_work() is possible to cause
NULL pointer dereference if the usb cable is disconnected while data
transfer is running.
In such case, a gadget driver may call usb_ep_disable()) before
xfer_work() is actually called. In this case, the usbhs_pkt_pop()
will call usbhsf_fifo_unselect(), and then usbhs_pipe_to_fifo()
in xfer_work() will return NULL.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On non-DeviceTree platforms, the index of serial device is a static
variable incremented on each probe. It is incremented even if deferred
probe happens when getting the clock in s3c24xx_serial_init_port().
This index is used for referencing elements of statically allocated
s3c24xx_serial_ports array. In case of re-probe, the index will point
outside of this array leading to memory corruption.
Increment the index only on successful probe.
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Fixes: b497549a035c ("[ARM] S3C24XX: Split serial driver into core and per-cpu drivers") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
e9532e69b8d1 ("sched/cputime: Fix steal time accounting vs. CPU hotplug")
... set rq->prev_* to 0 after a CPU hotplug comes back, in order to
fix the case where (after CPU hotplug) steal time is smaller than
rq->prev_steal_time.
However, this should never happen. Steal time was only smaller because of the
KVM-specific bug fixed by the previous patch. Worse, the previous patch
triggers a bug on CPU hot-unplug/plug operation: because
rq->prev_steal_time is cleared, all of the CPU's past steal time will be
accounted again on hot-plug.
Since the root cause has been fixed, we can just revert commit e9532e69b8d1.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 'commit e9532e69b8d1 ("sched/cputime: Fix steal time accounting vs. CPU hotplug")' Link: http://lkml.kernel.org/r/1465813966-3116-3-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
memory_hotplug_max() uses hot_add_drconf_memory_max() to get maxmimum
addressable memory by referring to ibm,dyanamic-memory property. There
are three problems with the current approach:
1 hot_add_drconf_memory_max() assumes that ibm,dynamic-memory includes
all the LMBs of the guest, but that is not true for PowerKVM which
populates only DR LMBs (LMBs that can be hotplugged/removed) in that
property.
2 hot_add_drconf_memory_max() multiplies lmb-size with lmb-count to arrive
at the max possible address. Since ibm,dynamic-memory doesn't include
RMA LMBs, the address thus obtained will be less than the actual max
address. For example, if max possible memory size is 32G, with lmb-size
of 256MB there can be 127 LMBs in ibm,dynamic-memory (1 LMB for RMA
which won't be present here). hot_add_drconf_memory_max() would then
return the max addressable memory as 127 * 256MB = 31.75GB, the max
address should have been 32G which is what ibm,lrdr-capacity shows.
3 In PowerKVM, there can be a gap between the end of boot time RAM and
beginning of hotplug RAM area. So just multiplying lmb-count with
lmb-size will not provide the correct max possible address for PowerKVM.
This patch fixes 1 by using ibm,lrdr-capacity property to return the max
addressable memory whenever the property is present. Then it fixes 2 & 3
by fetching the address of the last LMB in ibm,dynamic-memory property.
Fixes: cd34206e949b ("powerpc: Add memory_hotplug_max()") Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It seems risky to always rely on the caller to ensure the socket's
address family is correct before passing it to the NetLabel kAPI,
especially since we see at least one LSM which didn't. Add address
family checks to the *_delattr() functions to help prevent future
problems.
Reported-by: Maninder Singh <maninder1.s@samsung.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
faultin_page drops FOLL_WRITE after the page fault handler did the CoW
and then we retry follow_page_mask to get our CoWed page. This is racy,
however because the page might have been unmapped by that time and so
we would have to do a page fault again, this time without CoW. This
would cause the page cache corruption for FOLL_FORCE on MAP_PRIVATE
read only mappings with obvious consequences.
This is an ancient bug that was actually already fixed once by Linus
eleven years ago in commit 4ceb5db9757a ("Fix get_user_pages() race
for write access") but that was then undone due to problems on s390
by commit f33ea7f404e5 ("fix get_user_pages bug") because s390 didn't
have proper dirty pte tracking until abf09bed3cce ("s390/mm: implement
software dirty bits"). This wasn't a problem at the time as pointed out
by Hugh Dickins because madvise relied on mmap_sem for write up until 0a27a14a6292 ("mm: madvise avoid exclusive mmap_sem") but since then we
can race with madvise which can unmap the fresh COWed page or with KSM
and corrupt the content of the shared page.
This patch is based on the Linus' approach to not clear FOLL_WRITE after
the CoW page fault (aka VM_FAULT_WRITE) but instead introduces FOLL_COW
to note this fact. The flag is then rechecked during follow_pfn_pte to
enforce the page fault again if we do not see the CoWed page. Linus was
suggesting to check pte_dirty again as s390 is OK now. But that would
make backporting to some old kernels harder. So instead let's just make
sure that vm_normal_page sees a pure anonymous page.
This would guarantee we are seeing a real CoW page. Introduce
can_follow_write_pte which checks both pte_write and falls back to
PageAnon on forced write faults which passed CoW already. Thanks to Hugh
to point out that a special care has to be taken for KSM pages because
our COWed page might have been merged with a KSM one and keep its
PageAnon flag.
Fixes: 0a27a14a6292 ("mm: madvise avoid exclusive mmap_sem") Reported-by: Phil "not Paul" Oester <kernel@linuxace.com> Disclosed-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Michal Hocko <mhocko@suse.com>
[bwh: Backported to 3.2:
- Adjust filename, context, indentation
- The 'no_page' exit path in follow_page() is different, so open-code the
cleanup
- Delete a now-unused label] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There is a double fetch problem in audit_log_single_execve_arg()
where we first check the execve(2) argumnets for any "bad" characters
which would require hex encoding and then re-fetch the arguments for
logging in the audit record[1]. Of course this leaves a window of
opportunity for an unsavory application to munge with the data.
This patch reworks things by only fetching the argument data once[2]
into a buffer where it is scanned and logged into the audit
records(s). In addition to fixing the double fetch, this patch
improves on the original code in a few other ways: better handling
of large arguments which require encoding, stricter record length
checking, and some performance improvements (completely unverified,
but we got rid of some strlen() calls, that's got to be a good
thing).
As part of the development of this patch, I've also created a basic
regression test for the audit-testsuite, the test can be tracked on
GitHub at the following link:
[1] If you pay careful attention, there is actually a triple fetch
problem due to a strnlen_user() call at the top of the function.
[2] This is a tiny white lie, we do make a call to strnlen_user()
prior to fetching the argument data. I don't like it, but due to the
way the audit record is structured we really have no choice unless we
copy the entire argument at once (which would require a rather
wasteful allocation). The good news is that with this patch the
kernel no longer relies on this strnlen_user() value for anything
beyond recording it in the log, we also update it with a trustworthy
value whenever possible.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com> Signed-off-by: Paul Moore <paul@paul-moore.com>
[bwh: Backported to 3.2:
- In audit_log_execve_info() various information is retrieved via
the extra parameter struct audit_aux_data_execve *axi
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Yue Cao claims that current host rate limiting of challenge ACKS
(RFC 5961) could leak enough information to allow a patient attacker
to hijack TCP sessions. He will soon provide details in an academic
paper.
This patch increases the default limit from 100 to 1000, and adds
some randomization so that the attacker can no longer hijack
sessions without spending a considerable amount of probes.
Based on initial analysis and patch from Linus.
Note that we also have per socket rate limiting, so it is tempting
to remove the host limit in the future.
v2: randomize the count of challenge acks per second, not the period.
Fixes: 282f23c6ee34 ("tcp: implement RFC 5961 3.2") Reported-by: Yue Cao <ycao009@ucr.edu> Signed-off-by: Eric Dumazet <edumazet@google.com> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
- Adjust context
- Use ACCESS_ONCE() instead of {READ,WRITE}_ONCE()
- Open-code prandom_u32_max()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The last field "flags" of object "minfo" is not initialized.
Copying this object out may leak kernel stack data.
Assign 0 to it to avoid leak.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
link_info.str is a char array of size 60. Memory after the NULL
byte is not initialized. Sending the whole object out can cause
a leak.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: the unpadded strcpy() is in tipc_node_get_links()
and no nlattr is involved, so use strncpy()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The stack object “r1” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The stack object “r1” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The stack object “tread” has a total size of 32 bytes. Its field
“event” and “val” both contain 4 bytes padding. These 8 bytes
padding bytes are sent to user without being initialized.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The stack object “ci” has a total size of 8 bytes. Its last 3 bytes
are padding bytes which are not initialized and leaked to userland
via “copy_to_user”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This prevents stacking filesystems (ecryptfs and overlayfs) from using
procfs as lower filesystem. There is too much magic going on inside
procfs, and there is no good reason to stack stuff on top of procfs.
(For example, procfs does access checks in VFS open handlers, and
ecryptfs by design calls open handlers from a kernel thread that doesn't
drop privileges or so.)
Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Add a simple read-only counter to super_block that indicates how deep this
is in the stack of filesystems. Previously ecryptfs was the only stackable
filesystem and it explicitly disallowed multiple layers of itself.
Overlayfs, however, can be stacked recursively and also may be stacked
on top of ecryptfs or vice versa.
To limit the kernel stack usage we must limit the depth of the
filesystem stack. Initially the limit is set to 2.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
[bwh: Backported to 3.2:
- Drop changes to overlayfs
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In sess_auth_rawntlmssp_authenticate(), the ntlmssp blob is allocated
statically and its size is an "empirical" 5*sizeof(struct
_AUTHENTICATE_MESSAGE) (320B on x86_64). I don't know where this value
comes from or if it was ever appropriate, but it is currently
insufficient: the user and domain name in UTF16 could take 1kB by
themselves. Because of that, build_ntlmssp_auth_blob() might corrupt
memory (out-of-bounds write). The size of ntlmssp_blob in
SMB2_sess_setup() is too small too (sizeof(struct _NEGOTIATE_MESSAGE)
+ 500).
This patch allocates the blob dynamically in
build_ntlmssp_auth_blob().
Signed-off-by: Jerome Marchand <jmarchan@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com>
[bwh: Backported to 3.2:
- Adjust context, indentation
- build_ntlmssp_auth_blob() is static
- Drop changes to smb2pdu.c
- Use cERROR() instead of cifs_dbg(VFS, ...)
- Use MAX_USERNAME_SIZE instead of CIFS_MAX_USERNAME_LEN] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There are legitimate reasons to disallow mmap on certain files, notably
in sysfs or procfs. We shouldn't emulate mmap support on file systems
that don't offer support natively.
CVE-2016-1583
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
[tyhicks: clean up f_op check by using ecryptfs_file_to_lower()] Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A qeth_card contains a napi_struct linked to the net_device during
device probing. This struct must be deleted when removing the qeth
device, otherwise Panic on oops can occur when qeth devices are
repeatedly removed and added.
Fixes: a1c3ed4c9ca ("qeth: NAPI support for l2 and l3 discipline") Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Tested-by: Alexander Klein <ALKL@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The user timer tu->qused counter may go to a negative value when
multiple concurrent reads are performed since both the check and the
decrement of tu->qused are done in two individual locked contexts.
This results in bogus read outs, and the endless loop in the
user-space side.
The fix is to move the decrement of the tu->qused counter into the
same spinlock context as the zero-check of the counter.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ether_addr_equal_64bits() requires some care about its arguments,
namely that 8 bytes might be read, even if last 2 byte values are not
used.
KASan detected a violation with null_mac_addr and lacpdu_mcast_addr
in bond_3ad.c
Same problem with mac_bcast[] and mac_v6_allmcast[] in bond_alb.c :
Although the 8-byte alignment was there, KASan would detect out
of bound accesses.
Fixes: 815117adaf5b ("bonding: use ether_addr_equal_unaligned for bond addr compare") Fixes: bb54e58929f3 ("bonding: Verify RX LACPDU has proper dest mac-addr") Fixes: 885a136c52a8 ("bonding: use compare_ether_addr_64bits() in ALB") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Acked-by: Dmitry Vyukov <dvyukov@google.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
- Adjust filename
- Drop change to bond_params::ad_actor_system
- Fix one more copy of null_mac_addr to use eth_zero_addr()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
a lot of code has either the memset or an inefficient copy
from a static array that contains the all-zeros Ethernet address.
Introduce help function eth_zero_addr() to fill an address with
all zeros, making the code clearer and allowing us to get rid of
some constant arrays.
Signed-off-by: Duan Jiong <djduanjiong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix boot crash that triggers if this driver is built into a kernel and
run on non-AMD systems.
AMD northbridges users call amd_cache_northbridges() and it returns
a negative value to signal that we weren't able to cache/detect any
northbridges on the system.
At least, it should do so as all its callers expect it to do so. But it
does return a negative value only when kmalloc() fails.
Fix it to return -ENODEV if there are no NBs cached as otherwise, amd_nb
users like amd64_edac, for example, which relies on it to know whether
it should load or not, gets loaded on systems like Intel Xeons where it
shouldn't.
vortex_wtdma_bufshift() function does calculate the page index
wrongly, first masking then shift, which always results in zero.
The proper computation is to first shift, then mask.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The tt_req_node is added and removed from a list inside a spinlock. But the
locking is sometimes removed even when the object is still referenced and
will be used later via this reference. For example batadv_send_tt_request
can create a new tt_req_node (including add to a list) and later
re-acquires the lock to remove it from the list and to free it. But at this
time another context could have already removed this tt_req_node from the
list and freed it.
CPU#0
batadv_batman_skb_recv from net_device 0
-> batadv_iv_ogm_receive
-> batadv_iv_ogm_process
-> batadv_iv_ogm_process_per_outif
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_ogm_handler_v1
-> batadv_tt_update_orig
-> batadv_send_tt_request
-> batadv_tt_req_node_new
spin_lock(...)
allocates new tt_req_node and adds it to list
spin_unlock(...)
return tt_req_node
CPU#1
batadv_batman_skb_recv from net_device 1
-> batadv_recv_unicast_tvlv
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_unicast_handler_v1
-> batadv_handle_tt_response
spin_lock(...)
tt_req_node gets removed from list and is freed
spin_unlock(...)
CPU#0
<- returned to batadv_send_tt_request
spin_lock(...)
tt_req_node gets removed from list and is freed
MEMORY CORRUPTION/SEGFAULT/...
spin_unlock(...)
This can only be solved via reference counting to allow multiple contexts
to handle the list manipulation while making sure that only the last
context holding a reference will free the object.
Fixes: a73105b8d4c7 ("batman-adv: improved client announcement mechanism") Signed-off-by: Sven Eckelmann <sven@narfation.org> Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net> Tested-by: Amadeus Alfa <amadeus@chemnitz.freifunk.net> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2:
- Adjust context
- Use struct tt_req_node instead of struct batadv_tt_req_node
- Use list_empty() instead of hlist_unhashed()
- Drop kernel-doc change] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Olga Kornievskaia reports that the following test fails to trigger
an OPEN_DOWNGRADE on the wire, and only triggers the final CLOSE.
fd0 = open(foo, RDRW) -- should be open on the wire for "both"
fd1 = open(foo, RDONLY) -- should be open on the wire for "read"
close(fd0) -- should trigger an open_downgrade
read(fd1)
close(fd1)
The issue is that we're missing a check for whether or not the current
state transitioned from an O_RDWR state as opposed to having transitioned
from a combination of O_RDONLY and O_WRONLY.
Reported-by: Olga Kornievskaia <aglo@umich.edu> Fixes: cd9288ffaea4 ("NFSv4: Fix another bug in the close/open_downgrade code") Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
'commpage_bak' is allocated with 'sizeof(struct echoaudio)' bytes.
We then copy 'sizeof(struct comm_page)' bytes in it.
On my system, smatch complains because one is 2960 and the other is 3072.
This would result in memory corruption or a oops.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
sca3000_read_ctrl_reg() returns a negative number on failure, check for
this instead of zero.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The value `bytes' comes from the filesystem which is about to be
mounted. We cannot trust that the value is always in the range we
expect it to be.
Check its value before using it to calculate the length for the crc32_le
call. It value must be larger (or equal) sumoff + 4.
This fixes a kernel bug when accidentially mounting an image file which
had the nilfs2 magic value 0x3434 at the right offset 0x406 by chance.
The bytes 0x01 0x00 were stored at 0x408 and were interpreted as a
s_bytes value of 1. This caused an underflow when substracting sumoff +
4 (20) in the call to crc32_le.
This patch validates the num_values parameter from userland during the
HIDIOCGUSAGES and HIDIOCSUSAGES commands. Previously, if the report id was set
to HID_REPORT_ID_UNKNOWN, we would fail to validate the num_values parameter
leading to a heap overflow.
Signed-off-by: Scott Bauer <sbauer@plzdonthack.me> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The touchpad in HP Pavilion 14-ab057ca reports it's version as 12 and
according to Elan both 11 and 12 are valid IC types and should be
identified as hw_version 4.
Reported-by: Patrick Lessard <Patrick.Lessard@cogeco.com> Tested-by: Patrick Lessard <Patrick.Lessard@cogeco.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When calculating the required size of an RC QP send queue, leave
enough space for masked atomic operations, which require more space than
"regular" atomic operation.
Fixes: 6fa8f719844b ("IB/mlx4: Add support for masked atomic operations") Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Reviewed-by: Jack Morgenstein <jackm@mellanox.co.il> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Current overlap check is evaluating to false a case where a filter
field is fully contained (proper subset) of a r/w request. This
change applies classical overlap check instead to include all the
scenarios.
More specifically, for (Hilscher GmbH CIFX 50E-DP(M/S)) device driver
the logic is such that the entire confspace is read and written in 4
byte chunks. In this case as an example, CACHE_LINE_SIZE,
LATENCY_TIMER and PCI_BIST are arriving together in one call to
xen_pcibk_config_write() with offset == 0xc and size == 4. With the
exsisting overlap check the LATENCY_TIMER field (offset == 0xd, length
== 1) is fully contained in the write request and hence is excluded
from write, which is incorrect.
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...
This patch adds a private dellink function for the CAN device driver interface
that does just nothing.
It's a follow up to commit 993e6f2fd ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.
Reported-by: ajneu <ajneu1@gmail.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
During page migrations UBIFS might get confused
and the following assert triggers:
[ 213.480000] UBIFS assert failed in ubifs_set_page_dirty at 1451 (pid 436)
[ 213.490000] CPU: 0 PID: 436 Comm: drm-stress-test Not tainted 4.4.4-00176-geaa802524636-dirty #1008
[ 213.490000] Hardware name: Allwinner sun4i/sun5i Families
[ 213.490000] [<c0015e70>] (unwind_backtrace) from [<c0012cdc>] (show_stack+0x10/0x14)
[ 213.490000] [<c0012cdc>] (show_stack) from [<c02ad834>] (dump_stack+0x8c/0xa0)
[ 213.490000] [<c02ad834>] (dump_stack) from [<c0236ee8>] (ubifs_set_page_dirty+0x44/0x50)
[ 213.490000] [<c0236ee8>] (ubifs_set_page_dirty) from [<c00fa0bc>] (try_to_unmap_one+0x10c/0x3a8)
[ 213.490000] [<c00fa0bc>] (try_to_unmap_one) from [<c00fadb4>] (rmap_walk+0xb4/0x290)
[ 213.490000] [<c00fadb4>] (rmap_walk) from [<c00fb1bc>] (try_to_unmap+0x64/0x80)
[ 213.490000] [<c00fb1bc>] (try_to_unmap) from [<c010dc28>] (migrate_pages+0x328/0x7a0)
[ 213.490000] [<c010dc28>] (migrate_pages) from [<c00d0cb0>] (alloc_contig_range+0x168/0x2f4)
[ 213.490000] [<c00d0cb0>] (alloc_contig_range) from [<c010ec00>] (cma_alloc+0x170/0x2c0)
[ 213.490000] [<c010ec00>] (cma_alloc) from [<c001a958>] (__alloc_from_contiguous+0x38/0xd8)
[ 213.490000] [<c001a958>] (__alloc_from_contiguous) from [<c001ad44>] (__dma_alloc+0x23c/0x274)
[ 213.490000] [<c001ad44>] (__dma_alloc) from [<c001ae08>] (arm_dma_alloc+0x54/0x5c)
[ 213.490000] [<c001ae08>] (arm_dma_alloc) from [<c035cecc>] (drm_gem_cma_create+0xb8/0xf0)
[ 213.490000] [<c035cecc>] (drm_gem_cma_create) from [<c035cf20>] (drm_gem_cma_create_with_handle+0x1c/0xe8)
[ 213.490000] [<c035cf20>] (drm_gem_cma_create_with_handle) from [<c035d088>] (drm_gem_cma_dumb_create+0x3c/0x48)
[ 213.490000] [<c035d088>] (drm_gem_cma_dumb_create) from [<c0341ed8>] (drm_ioctl+0x12c/0x444)
[ 213.490000] [<c0341ed8>] (drm_ioctl) from [<c0121adc>] (do_vfs_ioctl+0x3f4/0x614)
[ 213.490000] [<c0121adc>] (do_vfs_ioctl) from [<c0121d30>] (SyS_ioctl+0x34/0x5c)
[ 213.490000] [<c0121d30>] (SyS_ioctl) from [<c000f2c0>] (ret_fast_syscall+0x0/0x34)
UBIFS is using PagePrivate() which can have different meanings across
filesystems. Therefore the generic page migration code cannot handle this
case correctly.
We have to implement our own migration function which basically does a
plain copy but also duplicates the page private flag.
UBIFS is not a block device filesystem and cannot use buffer_migrate_page().
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[rw: Massaged changelog, build fixes, etc...] Signed-off-by: Richard Weinberger <richard@nod.at> Acked-by: Christoph Hellwig <hch@lst.de>
[bwh: Backported to 3.2:
- migrate_page_move_mapping() doesn't take an extra_count parameter
- Use literal 0 instead of MIGRATEPAGE_SUCCESS] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Export these symbols such that UBIFS can implement
->migratepage.
Signed-off-by: Richard Weinberger <richard@nod.at> Acked-by: Christoph Hellwig <hch@lst.de>
[bwh: Backported to 3.2: also change migrate_page_move_mapping() from
static to extern, done as part of an earlier commit upstream] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
recover_peb() was never power cut aware,
if a power cut happened right after writing the VID header
upon next attach UBI would blindly use the new partial written
PEB and all data from the old PEB is lost.
In order to make recover_peb() power cut aware, write the new
VID with a proper crc and copy_flag set such that the UBI attach
process will detect whether the new PEB is completely written
or not.
We cannot directly use ubi_eba_atomic_leb_change() since we'd
have to unlock the LEB which is facing a write error.
Reported-by: Jörg Pfähler <pfaehler@isse.de> Reviewed-by: Jörg Pfähler <pfaehler@isse.de> Signed-off-by: Richard Weinberger <richard@nod.at>
[bwh: Backported to 3.2:
- Adjust context
- Use next_sqnum() instead of ubi_next_sqnum()
- Use ubi_device::peb_buf1 instead of ubi_device::peb_buf
- No need to unlock ubi->fm_eba_sem on error] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Tested-by: Amr Bekhit <amrbekhit@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
For security reasons ordinary user must not be able to control fan speed
via /proc/i8k by default. Some malicious software running under "nobody"
user could be able to turn fan off and cause HW problems. So this patch
changes default value of "restricted" parameter to 1.
Also restrict reading of DMI_PRODUCT_SERIAL from /proc/i8k via "restricted"
parameter. It is because non root user cannot read DMI_PRODUCT_SERIAL from
sysfs file /sys/class/dmi/id/product_serial.
Old non secure behaviour of file /proc/i8k can be achieved by loading this
module with "restricted" parameter set to 0.
Note that this patch has effects only for kernels compiled with CONFIG_I8K
and only for file /proc/i8k. Hwmon interface provided by this driver was
not changed and root access for setting fan speed was needed also before.
Reported-by: Mario Limonciello <Mario_Limonciello@dell.com> Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The isa_bus_init function must be called before drivers which utilize
the ISA bus driver are registered. A race condition for initilization
exists if device_initcall is used (the isa_bus_init callback is placed
in the same initcall level as dependent drivers which use module_init).
This patch ensures that isa_bus_init is called first by utilizing
postcore_initcall in favor of device_initcall.
Fixes: a5117ba7da37 ("[PATCH] Driver model: add ISA bus") Cc: Rene Herman <rene.herman@keyaccess.nl> Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
projects / pandora-kernel.git / log