board/compulab/cm_fx6/cm_fx6.c

   1 /*
   2  * Board functions for Compulab CM-FX6 board
   3  *
   4  * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
   5  *
   6  * Author: Nikita Kiryanov <nikita@compulab.co.il>
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #include <common.h>
  12 #include <dm.h>
  13 #include <fsl_esdhc.h>
  14 #include <miiphy.h>
  15 #include <netdev.h>
  16 #include <errno.h>
  17 #include <usb.h>
  18 #include <fdt_support.h>
  19 #include <sata.h>
  20 #include <splash.h>
  21 #include <asm/arch/crm_regs.h>
  22 #include <asm/arch/sys_proto.h>
  23 #include <asm/arch/iomux.h>
  24 #include <asm/arch/mxc_hdmi.h>
  25 #include <asm/imx-common/mxc_i2c.h>
  26 #include <asm/imx-common/sata.h>
  27 #include <asm/imx-common/video.h>
  28 #include <asm/io.h>
  29 #include <asm/gpio.h>
  30 #include <dm/platform_data/serial_mxc.h>
  31 #include "common.h"
  32 #include "../common/eeprom.h"
  33 #include "../common/common.h"
  34
  35 DECLARE_GLOBAL_DATA_PTR;
  36
  37 #ifdef CONFIG_SPLASH_SCREEN
  38 static struct splash_location cm_fx6_splash_locations[] = {
  39         {
  40                 .name = "sf",
  41                 .storage = SPLASH_STORAGE_SF,
  42                 .offset = 0x100000,
  43         },
  44 };
  45
  46 int splash_screen_prepare(void)
  47 {
  48         return splash_source_load(cm_fx6_splash_locations,
  49                                   ARRAY_SIZE(cm_fx6_splash_locations));
  50 }
  51 #endif
  52
  53 #ifdef CONFIG_IMX_HDMI
  54 static void cm_fx6_enable_hdmi(struct display_info_t const *dev)
  55 {
  56         struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
  57         imx_setup_hdmi();
  58         setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_IPU1_IPU_DI0_MASK);
  59         imx_enable_hdmi_phy();
  60 }
  61
  62 static struct display_info_t preset_hdmi_1024X768 = {
  63         .bus    = -1,
  64         .addr   = 0,
  65         .pixfmt = IPU_PIX_FMT_RGB24,
  66         .enable = cm_fx6_enable_hdmi,
  67         .mode   = {
  68                 .name           = "HDMI",
  69                 .refresh        = 60,
  70                 .xres           = 1024,
  71                 .yres           = 768,
  72                 .pixclock       = 40385,
  73                 .left_margin    = 220,
  74                 .right_margin   = 40,
  75                 .upper_margin   = 21,
  76                 .lower_margin   = 7,
  77                 .hsync_len      = 60,
  78                 .vsync_len      = 10,
  79                 .sync           = FB_SYNC_EXT,
  80                 .vmode          = FB_VMODE_NONINTERLACED,
  81         }
  82 };
  83
  84 static void cm_fx6_setup_display(void)
  85 {
  86         struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
  87
  88         enable_ipu_clock();
  89         clrbits_le32(&iomuxc_regs->gpr[3], MXC_CCM_CCGR3_IPU1_IPU_DI0_MASK);
  90 }
  91
  92 int board_video_skip(void)
  93 {
  94         int ret;
  95         struct display_info_t *preset;
  96         char const *panel = getenv("displaytype");
  97
  98         if (!panel) /* Also accept panel for backward compatibility */
  99                 panel = getenv("panel");
 100
 101         if (!panel)
 102                 return -ENOENT;
 103
 104         if (!strcmp(panel, "HDMI"))
 105                 preset = &preset_hdmi_1024X768;
 106         else
 107                 return -EINVAL;
 108
 109         ret = ipuv3_fb_init(&preset->mode, 0, preset->pixfmt);
 110         if (ret) {
 111                 printf("Can't init display %s: %d\n", preset->mode.name, ret);
 112                 return ret;
 113         }
 114
 115         preset->enable(preset);
 116         printf("Display: %s (%ux%u)\n", preset->mode.name, preset->mode.xres,
 117                preset->mode.yres);
 118
 119         return 0;
 120 }
 121 #else
 122 static inline void cm_fx6_setup_display(void) {}
 123 #endif /* CONFIG_VIDEO_IPUV3 */
 124
 125 #ifdef CONFIG_DWC_AHSATA
 126 static int cm_fx6_issd_gpios[] = {
 127         /* The order of the GPIOs in the array is important! */
 128         CM_FX6_SATA_LDO_EN,
 129         CM_FX6_SATA_PHY_SLP,
 130         CM_FX6_SATA_NRSTDLY,
 131         CM_FX6_SATA_PWREN,
 132         CM_FX6_SATA_NSTANDBY1,
 133         CM_FX6_SATA_NSTANDBY2,
 134 };
 135
 136 static void cm_fx6_sata_power(int on)
 137 {
 138         int i;
 139
 140         if (!on) { /* tell the iSSD that the power will be removed */
 141                 gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 1);
 142                 mdelay(10);
 143         }
 144
 145         for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) {
 146                 gpio_direction_output(cm_fx6_issd_gpios[i], on);
 147                 udelay(100);
 148         }
 149
 150         if (!on) /* for compatibility lower the power loss interrupt */
 151                 gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
 152 }
 153
 154 static iomux_v3_cfg_t const sata_pads[] = {
 155         /* SATA PWR */
 156         IOMUX_PADS(PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 157         IOMUX_PADS(PAD_EIM_A22__GPIO2_IO16    | MUX_PAD_CTRL(NO_PAD_CTRL)),
 158         IOMUX_PADS(PAD_EIM_D20__GPIO3_IO20    | MUX_PAD_CTRL(NO_PAD_CTRL)),
 159         IOMUX_PADS(PAD_EIM_A25__GPIO5_IO02    | MUX_PAD_CTRL(NO_PAD_CTRL)),
 160         /* SATA CTRL */
 161         IOMUX_PADS(PAD_ENET_TXD0__GPIO1_IO30  | MUX_PAD_CTRL(NO_PAD_CTRL)),
 162         IOMUX_PADS(PAD_EIM_D23__GPIO3_IO23    | MUX_PAD_CTRL(NO_PAD_CTRL)),
 163         IOMUX_PADS(PAD_EIM_D29__GPIO3_IO29    | MUX_PAD_CTRL(NO_PAD_CTRL)),
 164         IOMUX_PADS(PAD_EIM_A23__GPIO6_IO06    | MUX_PAD_CTRL(NO_PAD_CTRL)),
 165         IOMUX_PADS(PAD_EIM_BCLK__GPIO6_IO31   | MUX_PAD_CTRL(NO_PAD_CTRL)),
 166 };
 167
 168 static int cm_fx6_setup_issd(void)
 169 {
 170         int ret, i;
 171
 172         SETUP_IOMUX_PADS(sata_pads);
 173
 174         for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) {
 175                 ret = gpio_request(cm_fx6_issd_gpios[i], "sata");
 176                 if (ret)
 177                         return ret;
 178         }
 179
 180         ret = gpio_request(CM_FX6_SATA_PWLOSS_INT, "sata_pwloss_int");
 181         if (ret)
 182                 return ret;
 183
 184         return 0;
 185 }
 186
 187 #define CM_FX6_SATA_INIT_RETRIES        10
 188 int sata_initialize(void)
 189 {
 190         int err, i;
 191
 192         /* Make sure this gpio has logical 0 value */
 193         gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
 194         udelay(100);
 195         cm_fx6_sata_power(1);
 196
 197         for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) {
 198                 err = setup_sata();
 199                 if (err) {
 200                         printf("SATA setup failed: %d\n", err);
 201                         return err;
 202                 }
 203
 204                 udelay(100);
 205
 206                 err = __sata_initialize();
 207                 if (!err)
 208                         break;
 209
 210                 /* There is no device on the SATA port */
 211                 if (sata_port_status(0, 0) == 0)
 212                         break;
 213
 214                 /* There's a device, but link not established. Retry */
 215         }
 216
 217         return err;
 218 }
 219
 220 int sata_stop(void)
 221 {
 222         __sata_stop();
 223         cm_fx6_sata_power(0);
 224         mdelay(250);
 225
 226         return 0;
 227 }
 228 #else
 229 static int cm_fx6_setup_issd(void) { return 0; }
 230 #endif
 231
 232 #ifdef CONFIG_SYS_I2C_MXC
 233 #define I2C_PAD_CTRL    (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
 234                         PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
 235                         PAD_CTL_ODE | PAD_CTL_SRE_FAST)
 236
 237 I2C_PADS(i2c0_pads,
 238          PAD_EIM_D21__I2C1_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
 239          PAD_EIM_D21__GPIO3_IO21 | MUX_PAD_CTRL(I2C_PAD_CTRL),
 240          IMX_GPIO_NR(3, 21),
 241          PAD_EIM_D28__I2C1_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
 242          PAD_EIM_D28__GPIO3_IO28 | MUX_PAD_CTRL(I2C_PAD_CTRL),
 243          IMX_GPIO_NR(3, 28));
 244
 245 I2C_PADS(i2c1_pads,
 246          PAD_KEY_COL3__I2C2_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
 247          PAD_KEY_COL3__GPIO4_IO12 | MUX_PAD_CTRL(I2C_PAD_CTRL),
 248          IMX_GPIO_NR(4, 12),
 249          PAD_KEY_ROW3__I2C2_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
 250          PAD_KEY_ROW3__GPIO4_IO13 | MUX_PAD_CTRL(I2C_PAD_CTRL),
 251          IMX_GPIO_NR(4, 13));
 252
 253 I2C_PADS(i2c2_pads,
 254          PAD_GPIO_3__I2C3_SCL | MUX_PAD_CTRL(I2C_PAD_CTRL),
 255          PAD_GPIO_3__GPIO1_IO03 | MUX_PAD_CTRL(I2C_PAD_CTRL),
 256          IMX_GPIO_NR(1, 3),
 257          PAD_GPIO_6__I2C3_SDA | MUX_PAD_CTRL(I2C_PAD_CTRL),
 258          PAD_GPIO_6__GPIO1_IO06 | MUX_PAD_CTRL(I2C_PAD_CTRL),
 259          IMX_GPIO_NR(1, 6));
 260
 261
 262 static int cm_fx6_setup_one_i2c(int busnum, struct i2c_pads_info *pads)
 263 {
 264         int ret;
 265
 266         ret = setup_i2c(busnum, CONFIG_SYS_I2C_SPEED, 0x7f, pads);
 267         if (ret)
 268                 printf("Warning: I2C%d setup failed: %d\n", busnum, ret);
 269
 270         return ret;
 271 }
 272
 273 static int cm_fx6_setup_i2c(void)
 274 {
 275         int ret = 0, err;
 276
 277         /* i2c<x>_pads are wierd macro variables; we can't use an array */
 278         err = cm_fx6_setup_one_i2c(0, I2C_PADS_INFO(i2c0_pads));
 279         if (err)
 280                 ret = err;
 281         err = cm_fx6_setup_one_i2c(1, I2C_PADS_INFO(i2c1_pads));
 282         if (err)
 283                 ret = err;
 284         err = cm_fx6_setup_one_i2c(2, I2C_PADS_INFO(i2c2_pads));
 285         if (err)
 286                 ret = err;
 287
 288         return ret;
 289 }
 290 #else
 291 static int cm_fx6_setup_i2c(void) { return 0; }
 292 #endif
 293
 294 #ifdef CONFIG_USB_EHCI_MX6
 295 #define WEAK_PULLDOWN   (PAD_CTL_PUS_100K_DOWN |                \
 296                         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
 297                         PAD_CTL_HYS | PAD_CTL_SRE_SLOW)
 298 #define MX6_USBNC_BASEADDR      0x2184800
 299 #define USBNC_USB_H1_PWR_POL    (1 << 9)
 300
 301 static int cm_fx6_setup_usb_host(void)
 302 {
 303         int err;
 304
 305         err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst");
 306         if (err)
 307                 return err;
 308
 309         SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL));
 310         SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL));
 311
 312         return 0;
 313 }
 314
 315 static int cm_fx6_setup_usb_otg(void)
 316 {
 317         int err;
 318         struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
 319
 320         err = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr");
 321         if (err) {
 322                 printf("USB OTG pwr gpio request failed: %d\n", err);
 323                 return err;
 324         }
 325
 326         SETUP_IOMUX_PAD(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL));
 327         SETUP_IOMUX_PAD(PAD_ENET_RX_ER__USB_OTG_ID |
 328                                                 MUX_PAD_CTRL(WEAK_PULLDOWN));
 329         clrbits_le32(&iomux->gpr[1], IOMUXC_GPR1_OTG_ID_MASK);
 330         /* disable ext. charger detect, or it'll affect signal quality at dp. */
 331         return gpio_direction_output(SB_FX6_USB_OTG_PWR, 0);
 332 }
 333
 334 int board_usb_phy_mode(int port)
 335 {
 336         return USB_INIT_HOST;
 337 }
 338
 339 int board_ehci_hcd_init(int port)
 340 {
 341         int ret;
 342         u32 *usbnc_usb_uh1_ctrl = (u32 *)(MX6_USBNC_BASEADDR + 4);
 343
 344         /* Only 1 host controller in use. port 0 is OTG & needs no attention */
 345         if (port != 1)
 346                 return 0;
 347
 348         /* Set PWR polarity to match power switch's enable polarity */
 349         setbits_le32(usbnc_usb_uh1_ctrl, USBNC_USB_H1_PWR_POL);
 350         ret = gpio_direction_output(CM_FX6_USB_HUB_RST, 0);
 351         if (ret)
 352                 return ret;
 353
 354         udelay(10);
 355         ret = gpio_direction_output(CM_FX6_USB_HUB_RST, 1);
 356         if (ret)
 357                 return ret;
 358
 359         mdelay(1);
 360
 361         return 0;
 362 }
 363
 364 int board_ehci_power(int port, int on)
 365 {
 366         if (port == 0)
 367                 return gpio_direction_output(SB_FX6_USB_OTG_PWR, on);
 368
 369         return 0;
 370 }
 371 #else
 372 static int cm_fx6_setup_usb_otg(void) { return 0; }
 373 static int cm_fx6_setup_usb_host(void) { return 0; }
 374 #endif
 375
 376 #ifdef CONFIG_FEC_MXC
 377 #define ENET_PAD_CTRL           (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
 378                                  PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
 379
 380 static int mx6_rgmii_rework(struct phy_device *phydev)
 381 {
 382         unsigned short val;
 383
 384         /* Ar8031 phy SmartEEE feature cause link status generates glitch,
 385          * which cause ethernet link down/up issue, so disable SmartEEE
 386          */
 387         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x3);
 388         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x805d);
 389         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4003);
 390         val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
 391         val &= ~(0x1 << 8);
 392         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
 393
 394         /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
 395         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
 396         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
 397         phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
 398
 399         val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
 400         val &= 0xffe3;
 401         val |= 0x18;
 402         phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
 403
 404         /* introduce tx clock delay */
 405         phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
 406         val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
 407         val |= 0x0100;
 408         phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
 409
 410         return 0;
 411 }
 412
 413 int board_phy_config(struct phy_device *phydev)
 414 {
 415         mx6_rgmii_rework(phydev);
 416
 417         if (phydev->drv->config)
 418                 return phydev->drv->config(phydev);
 419
 420         return 0;
 421 }
 422
 423 static iomux_v3_cfg_t const enet_pads[] = {
 424         IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 425         IOMUX_PADS(PAD_ENET_MDC__ENET_MDC   | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 426         IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 427         IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 428         IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 429         IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 430         IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 431         IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 432         IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 433         IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 434         IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 435         IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 436         IOMUX_PADS(PAD_GPIO_0__CCM_CLKO1    | MUX_PAD_CTRL(NO_PAD_CTRL)),
 437         IOMUX_PADS(PAD_GPIO_3__CCM_CLKO2    | MUX_PAD_CTRL(NO_PAD_CTRL)),
 438         IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(0x84)),
 439         IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK  |
 440                                                 MUX_PAD_CTRL(ENET_PAD_CTRL)),
 441         IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL |
 442                                                 MUX_PAD_CTRL(ENET_PAD_CTRL)),
 443         IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL |
 444                                                 MUX_PAD_CTRL(ENET_PAD_CTRL)),
 445 };
 446
 447 static int handle_mac_address(char *env_var, uint eeprom_bus)
 448 {
 449         unsigned char enetaddr[6];
 450         int rc;
 451
 452         rc = eth_getenv_enetaddr(env_var, enetaddr);
 453         if (rc)
 454                 return 0;
 455
 456         rc = cl_eeprom_read_mac_addr(enetaddr, eeprom_bus);
 457         if (rc)
 458                 return rc;
 459
 460         if (!is_valid_ethaddr(enetaddr))
 461                 return -1;
 462
 463         return eth_setenv_enetaddr(env_var, enetaddr);
 464 }
 465
 466 #define SB_FX6_I2C_EEPROM_BUS   0
 467 #define NO_MAC_ADDR             "No MAC address found for %s\n"
 468 int board_eth_init(bd_t *bis)
 469 {
 470         int err;
 471
 472         if (handle_mac_address("ethaddr", CONFIG_SYS_I2C_EEPROM_BUS))
 473                 printf(NO_MAC_ADDR, "primary NIC");
 474
 475         if (handle_mac_address("eth1addr", SB_FX6_I2C_EEPROM_BUS))
 476                 printf(NO_MAC_ADDR, "secondary NIC");
 477
 478         SETUP_IOMUX_PADS(enet_pads);
 479         /* phy reset */
 480         err = gpio_request(CM_FX6_ENET_NRST, "enet_nrst");
 481         if (err)
 482                 printf("Etnernet NRST gpio request failed: %d\n", err);
 483         gpio_direction_output(CM_FX6_ENET_NRST, 0);
 484         udelay(500);
 485         gpio_set_value(CM_FX6_ENET_NRST, 1);
 486         enable_enet_clk(1);
 487         return cpu_eth_init(bis);
 488 }
 489 #endif
 490
 491 #ifdef CONFIG_NAND_MXS
 492 static iomux_v3_cfg_t const nand_pads[] = {
 493         IOMUX_PADS(PAD_NANDF_CLE__NAND_CLE     | MUX_PAD_CTRL(NO_PAD_CTRL)),
 494         IOMUX_PADS(PAD_NANDF_ALE__NAND_ALE     | MUX_PAD_CTRL(NO_PAD_CTRL)),
 495         IOMUX_PADS(PAD_NANDF_CS0__NAND_CE0_B   | MUX_PAD_CTRL(NO_PAD_CTRL)),
 496         IOMUX_PADS(PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
 497         IOMUX_PADS(PAD_NANDF_D0__NAND_DATA00   | MUX_PAD_CTRL(NO_PAD_CTRL)),
 498         IOMUX_PADS(PAD_NANDF_D1__NAND_DATA01   | MUX_PAD_CTRL(NO_PAD_CTRL)),
 499         IOMUX_PADS(PAD_NANDF_D2__NAND_DATA02   | MUX_PAD_CTRL(NO_PAD_CTRL)),
 500         IOMUX_PADS(PAD_NANDF_D3__NAND_DATA03   | MUX_PAD_CTRL(NO_PAD_CTRL)),
 501         IOMUX_PADS(PAD_NANDF_D4__NAND_DATA04   | MUX_PAD_CTRL(NO_PAD_CTRL)),
 502         IOMUX_PADS(PAD_NANDF_D5__NAND_DATA05   | MUX_PAD_CTRL(NO_PAD_CTRL)),
 503         IOMUX_PADS(PAD_NANDF_D6__NAND_DATA06   | MUX_PAD_CTRL(NO_PAD_CTRL)),
 504         IOMUX_PADS(PAD_NANDF_D7__NAND_DATA07   | MUX_PAD_CTRL(NO_PAD_CTRL)),
 505         IOMUX_PADS(PAD_SD4_CMD__NAND_RE_B      | MUX_PAD_CTRL(NO_PAD_CTRL)),
 506         IOMUX_PADS(PAD_SD4_CLK__NAND_WE_B      | MUX_PAD_CTRL(NO_PAD_CTRL)),
 507 };
 508
 509 static void cm_fx6_setup_gpmi_nand(void)
 510 {
 511         SETUP_IOMUX_PADS(nand_pads);
 512         /* Enable clock roots */
 513         enable_usdhc_clk(1, 3);
 514         enable_usdhc_clk(1, 4);
 515
 516         setup_gpmi_io_clk(MXC_CCM_CS2CDR_ENFC_CLK_PODF(0xf) |
 517                           MXC_CCM_CS2CDR_ENFC_CLK_PRED(1)   |
 518                           MXC_CCM_CS2CDR_ENFC_CLK_SEL(0));
 519 }
 520 #else
 521 static void cm_fx6_setup_gpmi_nand(void) {}
 522 #endif
 523
 524 #ifdef CONFIG_FSL_ESDHC
 525 static struct fsl_esdhc_cfg usdhc_cfg[3] = {
 526         {USDHC1_BASE_ADDR},
 527         {USDHC2_BASE_ADDR},
 528         {USDHC3_BASE_ADDR},
 529 };
 530
 531 static enum mxc_clock usdhc_clk[3] = {
 532         MXC_ESDHC_CLK,
 533         MXC_ESDHC2_CLK,
 534         MXC_ESDHC3_CLK,
 535 };
 536
 537 int board_mmc_init(bd_t *bis)
 538 {
 539         int i;
 540
 541         cm_fx6_set_usdhc_iomux();
 542         for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
 543                 usdhc_cfg[i].sdhc_clk = mxc_get_clock(usdhc_clk[i]);
 544                 usdhc_cfg[i].max_bus_width = 4;
 545                 fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
 546                 enable_usdhc_clk(1, i);
 547         }
 548
 549         return 0;
 550 }
 551 #endif
 552
 553 #ifdef CONFIG_MXC_SPI
 554 int cm_fx6_setup_ecspi(void)
 555 {
 556         cm_fx6_set_ecspi_iomux();
 557         return gpio_request(CM_FX6_ECSPI_BUS0_CS0, "ecspi_bus0_cs0");
 558 }
 559 #else
 560 int cm_fx6_setup_ecspi(void) { return 0; }
 561 #endif
 562
 563 #ifdef CONFIG_OF_BOARD_SETUP
 564 int ft_board_setup(void *blob, bd_t *bd)
 565 {
 566         uint8_t enetaddr[6];
 567
 568         /* MAC addr */
 569         if (eth_getenv_enetaddr("ethaddr", enetaddr)) {
 570                 fdt_find_and_setprop(blob,
 571                                      "/soc/aips-bus@02100000/ethernet@02188000",
 572                                      "local-mac-address", enetaddr, 6, 1);
 573         }
 574
 575         if (eth_getenv_enetaddr("eth1addr", enetaddr)) {
 576                 fdt_find_and_setprop(blob, "/eth@pcie", "local-mac-address",
 577                                      enetaddr, 6, 1);
 578         }
 579
 580         return 0;
 581 }
 582 #endif
 583
 584 int board_init(void)
 585 {
 586         int ret;
 587
 588         gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
 589         cm_fx6_setup_gpmi_nand();
 590
 591         ret = cm_fx6_setup_ecspi();
 592         if (ret)
 593                 printf("Warning: ECSPI setup failed: %d\n", ret);
 594
 595         ret = cm_fx6_setup_usb_otg();
 596         if (ret)
 597                 printf("Warning: USB OTG setup failed: %d\n", ret);
 598
 599         ret = cm_fx6_setup_usb_host();
 600         if (ret)
 601                 printf("Warning: USB host setup failed: %d\n", ret);
 602
 603         /*
 604          * cm-fx6 may have iSSD not assembled and in this case it has
 605          * bypasses for a (m)SATA socket on the baseboard. The socketed
 606          * device is not controlled by those GPIOs. So just print a warning
 607          * if the setup fails.
 608          */
 609         ret = cm_fx6_setup_issd();
 610         if (ret)
 611                 printf("Warning: iSSD setup failed: %d\n", ret);
 612
 613         /* Warn on failure but do not abort boot */
 614         ret = cm_fx6_setup_i2c();
 615         if (ret)
 616                 printf("Warning: I2C setup failed: %d\n", ret);
 617
 618         cm_fx6_setup_display();
 619
 620         return 0;
 621 }
 622
 623 int checkboard(void)
 624 {
 625         puts("Board: CM-FX6\n");
 626         return 0;
 627 }
 628
 629 int misc_init_r(void)
 630 {
 631         cl_print_pcb_info();
 632
 633         return 0;
 634 }
 635
 636 void dram_init_banksize(void)
 637 {
 638         gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 639         gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
 640
 641         switch (gd->ram_size) {
 642         case 0x10000000: /* DDR_16BIT_256MB */
 643                 gd->bd->bi_dram[0].size = 0x10000000;
 644                 gd->bd->bi_dram[1].size = 0;
 645                 break;
 646         case 0x20000000: /* DDR_32BIT_512MB */
 647                 gd->bd->bi_dram[0].size = 0x20000000;
 648                 gd->bd->bi_dram[1].size = 0;
 649                 break;
 650         case 0x40000000:
 651                 if (is_cpu_type(MXC_CPU_MX6SOLO)) { /* DDR_32BIT_1GB */
 652                         gd->bd->bi_dram[0].size = 0x20000000;
 653                         gd->bd->bi_dram[1].size = 0x20000000;
 654                 } else { /* DDR_64BIT_1GB */
 655                         gd->bd->bi_dram[0].size = 0x40000000;
 656                         gd->bd->bi_dram[1].size = 0;
 657                 }
 658                 break;
 659         case 0x80000000: /* DDR_64BIT_2GB */
 660                 gd->bd->bi_dram[0].size = 0x40000000;
 661                 gd->bd->bi_dram[1].size = 0x40000000;
 662                 break;
 663         case 0xEFF00000: /* DDR_64BIT_4GB */
 664                 gd->bd->bi_dram[0].size = 0x70000000;
 665                 gd->bd->bi_dram[1].size = 0x7FF00000;
 666                 break;
 667         }
 668 }
 669
 670 int dram_init(void)
 671 {
 672         gd->ram_size = imx_ddr_size();
 673         switch (gd->ram_size) {
 674         case 0x10000000:
 675         case 0x20000000:
 676         case 0x40000000:
 677         case 0x80000000:
 678                 break;
 679         case 0xF0000000:
 680                 gd->ram_size -= 0x100000;
 681                 break;
 682         default:
 683                 printf("ERROR: Unsupported DRAM size 0x%lx\n", gd->ram_size);
 684                 return -1;
 685         }
 686
 687         return 0;
 688 }
 689
 690 u32 get_board_rev(void)
 691 {
 692         return cl_eeprom_get_board_rev();
 693 }
 694
 695 static struct mxc_serial_platdata cm_fx6_mxc_serial_plat = {
 696         .reg = (struct mxc_uart *)UART4_BASE,
 697 };
 698
 699 U_BOOT_DEVICE(cm_fx6_serial) = {
 700         .name   = "serial_mxc",
 701         .platdata = &cm_fx6_mxc_serial_plat,
 702 };