* Driver for ST STV0367 DVB-T & DVB-C demodulator IC.
*
* Copyright (C) ST Microelectronics.
- * Copyright (C) 2010 NetUP Inc.
- * Copyright (C) 2010 Igor M. Liplianin <liplianin@netup.ru>
+ * Copyright (C) 2010,2011 NetUP Inc.
+ * Copyright (C) 2010,2011 Igor M. Liplianin <liplianin@netup.ru>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
config VIDEO_CX23885
tristate "Conexant cx23885 (2388x successor) support"
- depends on DVB_CORE && VIDEO_DEV && PCI && I2C && INPUT
+ depends on DVB_CORE && VIDEO_DEV && PCI && I2C && INPUT && SND
+ select SND_PCM
select I2C_ALGOBIT
select VIDEO_BTCX
select VIDEO_TUNER
#include <linux/pci.h>
#include <linux/delay.h>
#include <media/cx25840.h>
+#include <linux/firmware.h>
+#include <staging/altera.h>
#include "cx23885.h"
#include "tuner-xc2028.h"
#include "netup-init.h"
+#include "altera-ci.h"
+#include "xc5000.h"
#include "cx23888-ir.h"
static unsigned int enable_885_ir;
.portb = CX23885_MPEG_DVB,
},
[CX23885_BOARD_NETUP_DUAL_DVBS2_CI] = {
- .cimax = 1,
+ .ci_type = 1,
.name = "NetUP Dual DVB-S2 CI",
.portb = CX23885_MPEG_DVB,
.portc = CX23885_MPEG_DVB,
CX25840_SVIDEO_CHROMA4,
} },
},
+ [CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF] = {
+ .ci_type = 2,
+ .name = "NetUP Dual DVB-T/C-CI RF",
+ .porta = CX23885_ANALOG_VIDEO,
+ .portb = CX23885_MPEG_DVB,
+ .portc = CX23885_MPEG_DVB,
+ .tuner_type = TUNER_XC5000,
+ .tuner_addr = 0x64,
+ .input = { {
+ .type = CX23885_VMUX_TELEVISION,
+ .vmux = CX25840_COMPOSITE1,
+ } },
+ },
};
const unsigned int cx23885_bcount = ARRAY_SIZE(cx23885_boards);
.subvendor = 0x5654,
.subdevice = 0x2390,
.card = CX23885_BOARD_GOTVIEW_X5_3D_HYBRID,
+ }, {
+ .subvendor = 0x1b55,
+ .subdevice = 0xe2e4,
+ .card = CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF,
},
};
const unsigned int cx23885_idcount = ARRAY_SIZE(cx23885_subids);
/* Tuner Reset Command */
bitmask = 0x02;
break;
+ case CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF:
+ altera_ci_tuner_reset(dev, port->nr);
+ break;
}
if (bitmask) {
case CX23885_BOARD_GOTVIEW_X5_3D_HYBRID:
cx_set(GP0_IO, 0x00010001); /* Bring the part out of reset */
break;
+ case CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF:
+ /* GPIO-0 ~INT in
+ GPIO-1 TMS out
+ GPIO-2 ~reset chips out
+ GPIO-3 to GPIO-10 data/addr for CA in/out
+ GPIO-11 ~CS out
+ GPIO-12 ADDR out
+ GPIO-13 ~WR out
+ GPIO-14 ~RD out
+ GPIO-15 ~RDY in
+ GPIO-16 TCK out
+ GPIO-17 TDO in
+ GPIO-18 TDI out
+ */
+ cx_set(GP0_IO, 0x00060000); /* GPIO-1,2 as out */
+ /* GPIO-0 as INT, reset & TMS low */
+ cx_clear(GP0_IO, 0x00010006);
+ mdelay(100);/* reset delay */
+ cx_set(GP0_IO, 0x00000004); /* reset high */
+ cx_write(MC417_CTL, 0x00000037);/* enable GPIO-3..18 pins */
+ /* GPIO-17 is TDO in, GPIO-15 is ~RDY in, rest is out */
+ cx_write(MC417_OEN, 0x00005000);
+ /* ~RD, ~WR high; ADDR low; ~CS high */
+ cx_write(MC417_RWD, 0x00000d00);
+ /* enable irq */
+ cx_write(GPIO_ISM, 0x00000000);/* INTERRUPTS active low*/
+ break;
}
}
}
}
+int netup_jtag_io(void *device, int tms, int tdi, int read_tdo)
+{
+ int data;
+ int tdo = 0;
+ struct cx23885_dev *dev = (struct cx23885_dev *)device;
+ /*TMS*/
+ data = ((cx_read(GP0_IO)) & (~0x00000002));
+ data |= (tms ? 0x00020002 : 0x00020000);
+ cx_write(GP0_IO, data);
+
+ /*TDI*/
+ data = ((cx_read(MC417_RWD)) & (~0x0000a000));
+ data |= (tdi ? 0x00008000 : 0);
+ cx_write(MC417_RWD, data);
+ if (read_tdo)
+ tdo = (data & 0x00004000) ? 1 : 0; /*TDO*/
+
+ cx_write(MC417_RWD, data | 0x00002000);
+ udelay(1);
+ /*TCK*/
+ cx_write(MC417_RWD, data);
+
+ return tdo;
+}
+
void cx23885_ir_pci_int_enable(struct cx23885_dev *dev)
{
switch (dev->board) {
ts1->src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
break;
case CX23885_BOARD_NETUP_DUAL_DVBS2_CI:
+ case CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF:
ts1->gen_ctrl_val = 0xc; /* Serial bus + punctured clock */
ts1->ts_clk_en_val = 0x1; /* Enable TS_CLK */
ts1->src_sel_val = CX23885_SRC_SEL_PARALLEL_MPEG_VIDEO;
case CX23885_BOARD_LEADTEK_WINFAST_PXDVR3200_H:
case CX23885_BOARD_COMPRO_VIDEOMATE_E650F:
case CX23885_BOARD_NETUP_DUAL_DVBS2_CI:
+ case CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF:
case CX23885_BOARD_COMPRO_VIDEOMATE_E800:
case CX23885_BOARD_HAUPPAUGE_HVR1850:
case CX23885_BOARD_MYGICA_X8506:
case CX23885_BOARD_NETUP_DUAL_DVBS2_CI:
netup_initialize(dev);
break;
+ case CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF: {
+ int ret;
+ const struct firmware *fw;
+ const char *filename = "dvb-netup-altera-01.fw";
+ char *action = "configure";
+ struct altera_config netup_config = {
+ .dev = dev,
+ .action = action,
+ .jtag_io = netup_jtag_io,
+ };
+
+ netup_initialize(dev);
+
+ ret = request_firmware(&fw, filename, &dev->pci->dev);
+ if (ret != 0)
+ printk(KERN_ERR "did not find the firmware file. (%s) "
+ "Please see linux/Documentation/dvb/ for more details "
+ "on firmware-problems.", filename);
+ else
+ altera_init(&netup_config, fw);
+
+ break;
+ }
}
}
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <asm/div64.h>
+#include <linux/firmware.h>
#include "cx23885.h"
#include "cimax2.h"
+#include "altera-ci.h"
#include "cx23888-ir.h"
#include "cx23885-ir.h"
#include "cx23885-av.h"
dev->pci_bus = dev->pci->bus->number;
dev->pci_slot = PCI_SLOT(dev->pci->devfn);
cx23885_irq_add(dev, 0x001f00);
- if (cx23885_boards[dev->board].cimax > 0)
- cx23885_irq_add(dev, 0x01800000); /* for CiMaxes */
/* External Master 1 Bus */
dev->i2c_bus[0].nr = 0;
PCI_MSK_IR);
}
- if (cx23885_boards[dev->board].cimax > 0 &&
- ((pci_status & PCI_MSK_GPIO0) ||
- (pci_status & PCI_MSK_GPIO1))) {
+ if (cx23885_boards[dev->board].ci_type == 1 &&
+ (pci_status & (PCI_MSK_GPIO1 | PCI_MSK_GPIO0)))
+ handled += netup_ci_slot_status(dev, pci_status);
- if (cx23885_boards[dev->board].cimax > 0)
- handled += netup_ci_slot_status(dev, pci_status);
-
- }
+ if (cx23885_boards[dev->board].ci_type == 2 &&
+ (pci_status & PCI_MSK_GPIO0))
+ handled += altera_ci_irq(dev);
if (ts1_status) {
if (cx23885_boards[dev->board].portb == CX23885_MPEG_DVB)
switch (dev->board) {
case CX23885_BOARD_NETUP_DUAL_DVBS2_CI:
- cx23885_irq_add_enable(dev, 0x01800000); /* for NetUP */
+ cx23885_irq_add_enable(dev, PCI_MSK_GPIO1 | PCI_MSK_GPIO0);
+ break;
+ case CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF:
+ cx23885_irq_add_enable(dev, PCI_MSK_GPIO0);
break;
}
#include "atbm8830.h"
#include "ds3000.h"
#include "cx23885-f300.h"
+#include "altera-ci.h"
+#include "stv0367.h"
static unsigned int debug;
cx23885_free_buffer(q, (struct cx23885_buffer *)vb);
}
+static void cx23885_dvb_gate_ctrl(struct cx23885_tsport *port, int open)
+{
+ struct videobuf_dvb_frontends *f;
+ struct videobuf_dvb_frontend *fe;
+
+ f = &port->frontends;
+
+ if (f->gate <= 1) /* undefined or fe0 */
+ fe = videobuf_dvb_get_frontend(f, 1);
+ else
+ fe = videobuf_dvb_get_frontend(f, f->gate);
+
+ if (fe && fe->dvb.frontend && fe->dvb.frontend->ops.i2c_gate_ctrl)
+ fe->dvb.frontend->ops.i2c_gate_ctrl(fe->dvb.frontend, open);
+}
+
static struct videobuf_queue_ops dvb_qops = {
.buf_setup = dvb_buf_setup,
.buf_prepare = dvb_buf_prepare,
.i2c_address = 0x60,
.osc_clk = 20
};
+static struct stv0367_config netup_stv0367_config[] = {
+ {
+ .demod_address = 0x1c,
+ .xtal = 27000000,
+ .if_khz = 4500,
+ .if_iq_mode = 0,
+ .ts_mode = 1,
+ .clk_pol = 0,
+ }, {
+ .demod_address = 0x1d,
+ .xtal = 27000000,
+ .if_khz = 4500,
+ .if_iq_mode = 0,
+ .ts_mode = 1,
+ .clk_pol = 0,
+ },
+};
+
+static struct xc5000_config netup_xc5000_config[] = {
+ {
+ .i2c_address = 0x61,
+ .if_khz = 4500,
+ }, {
+ .i2c_address = 0x64,
+ .if_khz = 4500,
+ },
+};
+
+int netup_altera_fpga_rw(void *device, int flag, int data, int read)
+{
+ struct cx23885_dev *dev = (struct cx23885_dev *)device;
+ unsigned long timeout = jiffies + msecs_to_jiffies(1);
+ int mem = 0;
+
+ cx_set(MC417_RWD, ALT_RD | ALT_WR | ALT_CS);
+ if (read)
+ cx_set(MC417_OEN, ALT_DATA);
+ else {
+ cx_clear(MC417_OEN, ALT_DATA);/* D0-D7 out */
+ mem = cx_read(MC417_RWD);
+ mem &= ~ALT_DATA;
+ mem |= (data & ALT_DATA);
+ cx_write(MC417_RWD, mem);
+ }
+
+ if (flag)
+ cx_set(MC417_RWD, ALT_AD_RG);/* ADDR */
+ else
+ cx_clear(MC417_RWD, ALT_AD_RG);/* VAL */
+
+ cx_clear(MC417_RWD, ALT_CS);/* ~CS */
+ if (read)
+ cx_clear(MC417_RWD, ALT_RD);
+ else
+ cx_clear(MC417_RWD, ALT_WR);
+
+ for (;;) {
+ mem = cx_read(MC417_RWD);
+ if ((mem & ALT_RDY) == 0)
+ break;
+ if (time_after(jiffies, timeout))
+ break;
+ udelay(1);
+ }
+
+ cx_set(MC417_RWD, ALT_RD | ALT_WR | ALT_CS);
+ if (read)
+ return mem & ALT_DATA;
+
+ return 0;
+};
static int dvb_register(struct cx23885_tsport *port)
{
struct cx23885_dev *dev = port->dev;
struct cx23885_i2c *i2c_bus = NULL, *i2c_bus2 = NULL;
- struct videobuf_dvb_frontend *fe0;
+ struct videobuf_dvb_frontend *fe0, *fe1 = NULL;
+ int mfe_shared = 0; /* bus not shared by default */
int ret;
/* Get the first frontend */
/* init struct videobuf_dvb */
fe0->dvb.name = dev->name;
+ /* multi-frontend gate control is undefined or defaults to fe0 */
+ port->frontends.gate = 0;
+
+ /* Sets the gate control callback to be used by i2c command calls */
+ port->gate_ctrl = cx23885_dvb_gate_ctrl;
+
/* init frontend */
switch (dev->board) {
case CX23885_BOARD_HAUPPAUGE_HVR1250:
break;
}
break;
-
+ case CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF:
+ i2c_bus = &dev->i2c_bus[0];
+ mfe_shared = 1;/* MFE */
+ port->frontends.gate = 0;/* not clear for me yet */
+ /* ports B, C */
+ /* MFE frontend 1 DVB-T */
+ fe0->dvb.frontend = dvb_attach(stv0367ter_attach,
+ &netup_stv0367_config[port->nr - 1],
+ &i2c_bus->i2c_adap);
+ if (fe0->dvb.frontend != NULL)
+ if (NULL == dvb_attach(xc5000_attach,
+ fe0->dvb.frontend,
+ &i2c_bus->i2c_adap,
+ &netup_xc5000_config[port->nr - 1]))
+ goto frontend_detach;
+ /* MFE frontend 2 */
+ fe1 = videobuf_dvb_get_frontend(&port->frontends, 2);
+ if (fe1 == NULL)
+ goto frontend_detach;
+ /* DVB-C init */
+ fe1->dvb.frontend = dvb_attach(stv0367cab_attach,
+ &netup_stv0367_config[port->nr - 1],
+ &i2c_bus->i2c_adap);
+ if (fe1->dvb.frontend != NULL) {
+ fe1->dvb.frontend->id = 1;
+ if (NULL == dvb_attach(xc5000_attach,
+ fe1->dvb.frontend,
+ &i2c_bus->i2c_adap,
+ &netup_xc5000_config[port->nr - 1]))
+ goto frontend_detach;
+ }
+ break;
default:
printk(KERN_INFO "%s: The frontend of your DVB/ATSC card "
" isn't supported yet\n",
dev->name);
break;
}
- if (NULL == fe0->dvb.frontend) {
+
+ if ((NULL == fe0->dvb.frontend) || (fe1 && NULL == fe1->dvb.frontend)) {
printk(KERN_ERR "%s: frontend initialization failed\n",
- dev->name);
- return -1;
+ dev->name);
+ goto frontend_detach;
}
+
/* define general-purpose callback pointer */
fe0->dvb.frontend->callback = cx23885_tuner_callback;
+ if (fe1)
+ fe1->dvb.frontend->callback = cx23885_tuner_callback;
+#if 0
+ /* Ensure all frontends negotiate bus access */
+ fe0->dvb.frontend->ops.ts_bus_ctrl = cx23885_dvb_bus_ctrl;
+ if (fe1)
+ fe1->dvb.frontend->ops.ts_bus_ctrl = cx23885_dvb_bus_ctrl;
+#endif
/* Put the analog decoder in standby to keep it quiet */
call_all(dev, core, s_power, 0);
/* register everything */
ret = videobuf_dvb_register_bus(&port->frontends, THIS_MODULE, port,
- &dev->pci->dev, adapter_nr, 0,
+ &dev->pci->dev, adapter_nr, mfe_shared,
cx23885_dvb_fe_ioctl_override);
if (ret)
- return ret;
+ goto frontend_detach;
/* init CI & MAC */
switch (dev->board) {
netup_ci_init(port);
break;
}
+ case CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF: {
+ struct altera_ci_config netup_ci_cfg = {
+ .dev = dev,/* magic number to identify*/
+ .adapter = &port->frontends.adapter,/* for CI */
+ .demux = &fe0->dvb.demux,/* for hw pid filter */
+ .fpga_rw = netup_altera_fpga_rw,
+ };
+
+ altera_ci_init(&netup_ci_cfg, port->nr);
+ break;
+ }
case CX23885_BOARD_TEVII_S470: {
u8 eeprom[256]; /* 24C02 i2c eeprom */
}
return ret;
+
+frontend_detach:
+ port->gate_ctrl = NULL;
+ videobuf_dvb_dealloc_frontends(&port->frontends);
+ return -EINVAL;
}
int cx23885_dvb_register(struct cx23885_tsport *port)
case CX23885_BOARD_NETUP_DUAL_DVBS2_CI:
netup_ci_exit(port);
break;
+ case CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF:
+ altera_ci_release(port->dev, port->nr);
+ break;
}
+ port->gate_ctrl = NULL;
+
return 0;
}
#define CX23885_BOARD_MYGICA_X8558PRO 27
#define CX23885_BOARD_LEADTEK_WINFAST_PXTV1200 28
#define CX23885_BOARD_GOTVIEW_X5_3D_HYBRID 29
+#define CX23885_BOARD_NETUP_DUAL_DVB_T_C_CI_RF 30
#define GPIO_0 0x00000001
#define GPIO_1 0x00000002
*/
u32 clk_freq;
struct cx23885_input input[MAX_CX23885_INPUT];
- int cimax; /* for NetUP */
+ int ci_type; /* for NetUP */
};
struct cx23885_subid {
/* Allow a single tsport to have multiple frontends */
u32 num_frontends;
+ void (*gate_ctrl)(struct cx23885_tsport *port, int open);
void *port_priv;
};
git.openpandora.org / pandora-kernel.git / commitdiff