drivers/usb/host/ohci-hcd.c

   1 /*
   2  * OHCI HCD (Host Controller Driver) for USB.
   3  *
   4  * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
   5  * (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net>
   6  *
   7  * [ Initialisation is based on Linus'  ]
   8  * [ uhci code and gregs ohci fragments ]
   9  * [ (C) Copyright 1999 Linus Torvalds  ]
  10  * [ (C) Copyright 1999 Gregory P. Smith]
  11  *
  12  *
  13  * OHCI is the main "non-Intel/VIA" standard for USB 1.1 host controller
  14  * interfaces (though some non-x86 Intel chips use it).  It supports
  15  * smarter hardware than UHCI.  A download link for the spec available
  16  * through the http://www.usb.org website.
  17  *
  18  * This file is licenced under the GPL.
  19  */
  20
  21 #include <linux/module.h>
  22 #include <linux/moduleparam.h>
  23 #include <linux/pci.h>
  24 #include <linux/kernel.h>
  25 #include <linux/delay.h>
  26 #include <linux/ioport.h>
  27 #include <linux/sched.h>
  28 #include <linux/slab.h>
  29 #include <linux/smp_lock.h>
  30 #include <linux/errno.h>
  31 #include <linux/init.h>
  32 #include <linux/timer.h>
  33 #include <linux/list.h>
  34 #include <linux/usb.h>
  35 #include <linux/usb/otg.h>
  36 #include <linux/dma-mapping.h>
  37 #include <linux/dmapool.h>
  38 #include <linux/reboot.h>
  39
  40 #include <asm/io.h>
  41 #include <asm/irq.h>
  42 #include <asm/system.h>
  43 #include <asm/unaligned.h>
  44 #include <asm/byteorder.h>
  45 #ifdef CONFIG_PPC_PS3
  46 #include <asm/firmware.h>
  47 #endif
  48
  49 #include "../core/hcd.h"
  50
  51 #define DRIVER_VERSION "2006 August 04"
  52 #define DRIVER_AUTHOR "Roman Weissgaerber, David Brownell"
  53 #define DRIVER_DESC "USB 1.1 'Open' Host Controller (OHCI) Driver"
  54
  55 /*-------------------------------------------------------------------------*/
  56
  57 #undef OHCI_VERBOSE_DEBUG       /* not always helpful */
  58
  59 /* For initializing controller (mask in an HCFS mode too) */
  60 #define OHCI_CONTROL_INIT       OHCI_CTRL_CBSR
  61 #define OHCI_INTR_INIT \
  62                 (OHCI_INTR_MIE | OHCI_INTR_RHSC | OHCI_INTR_UE \
  63                 | OHCI_INTR_RD | OHCI_INTR_WDH)
  64
  65 #ifdef __hppa__
  66 /* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */
  67 #define IR_DISABLE
  68 #endif
  69
  70 #ifdef CONFIG_ARCH_OMAP
  71 /* OMAP doesn't support IR (no SMM; not needed) */
  72 #define IR_DISABLE
  73 #endif
  74
  75 /*-------------------------------------------------------------------------*/
  76
  77 static const char       hcd_name [] = "ohci_hcd";
  78
  79 #define STATECHANGE_DELAY       msecs_to_jiffies(300)
  80
  81 #include "ohci.h"
  82
  83 static void ohci_dump (struct ohci_hcd *ohci, int verbose);
  84 static int ohci_init (struct ohci_hcd *ohci);
  85 static void ohci_stop (struct usb_hcd *hcd);
  86
  87 #include "ohci-hub.c"
  88 #include "ohci-dbg.c"
  89 #include "ohci-mem.c"
  90 #include "ohci-q.c"
  91
  92
  93 /*
  94  * On architectures with edge-triggered interrupts we must never return
  95  * IRQ_NONE.
  96  */
  97 #if defined(CONFIG_SA1111)  /* ... or other edge-triggered systems */
  98 #define IRQ_NOTMINE     IRQ_HANDLED
  99 #else
 100 #define IRQ_NOTMINE     IRQ_NONE
 101 #endif
 102
 103
 104 /* Some boards misreport power switching/overcurrent */
 105 static int distrust_firmware = 1;
 106 module_param (distrust_firmware, bool, 0);
 107 MODULE_PARM_DESC (distrust_firmware,
 108         "true to distrust firmware power/overcurrent setup");
 109
 110 /* Some boards leave IR set wrongly, since they fail BIOS/SMM handshakes */
 111 static int no_handshake = 0;
 112 module_param (no_handshake, bool, 0);
 113 MODULE_PARM_DESC (no_handshake, "true (not default) disables BIOS handshake");
 114
 115 /*-------------------------------------------------------------------------*/
 116
 117 /*
 118  * queue up an urb for anything except the root hub
 119  */
 120 static int ohci_urb_enqueue (
 121         struct usb_hcd  *hcd,
 122         struct usb_host_endpoint *ep,
 123         struct urb      *urb,
 124         gfp_t           mem_flags
 125 ) {
 126         struct ohci_hcd *ohci = hcd_to_ohci (hcd);
 127         struct ed       *ed;
 128         urb_priv_t      *urb_priv;
 129         unsigned int    pipe = urb->pipe;
 130         int             i, size = 0;
 131         unsigned long   flags;
 132         int             retval = 0;
 133
 134 #ifdef OHCI_VERBOSE_DEBUG
 135         urb_print (urb, "SUB", usb_pipein (pipe));
 136 #endif
 137
 138         /* every endpoint has a ed, locate and maybe (re)initialize it */
 139         if (! (ed = ed_get (ohci, ep, urb->dev, pipe, urb->interval)))
 140                 return -ENOMEM;
 141
 142         /* for the private part of the URB we need the number of TDs (size) */
 143         switch (ed->type) {
 144                 case PIPE_CONTROL:
 145                         /* td_submit_urb() doesn't yet handle these */
 146                         if (urb->transfer_buffer_length > 4096)
 147                                 return -EMSGSIZE;
 148
 149                         /* 1 TD for setup, 1 for ACK, plus ... */
 150                         size = 2;
 151                         /* FALLTHROUGH */
 152                 // case PIPE_INTERRUPT:
 153                 // case PIPE_BULK:
 154                 default:
 155                         /* one TD for every 4096 Bytes (can be upto 8K) */
 156                         size += urb->transfer_buffer_length / 4096;
 157                         /* ... and for any remaining bytes ... */
 158                         if ((urb->transfer_buffer_length % 4096) != 0)
 159                                 size++;
 160                         /* ... and maybe a zero length packet to wrap it up */
 161                         if (size == 0)
 162                                 size++;
 163                         else if ((urb->transfer_flags & URB_ZERO_PACKET) != 0
 164                                 && (urb->transfer_buffer_length
 165                                         % usb_maxpacket (urb->dev, pipe,
 166                                                 usb_pipeout (pipe))) == 0)
 167                                 size++;
 168                         break;
 169                 case PIPE_ISOCHRONOUS: /* number of packets from URB */
 170                         size = urb->number_of_packets;
 171                         break;
 172         }
 173
 174         /* allocate the private part of the URB */
 175         urb_priv = kmalloc (sizeof (urb_priv_t) + size * sizeof (struct td *),
 176                         mem_flags);
 177         if (!urb_priv)
 178                 return -ENOMEM;
 179         memset (urb_priv, 0, sizeof (urb_priv_t) + size * sizeof (struct td *));
 180         INIT_LIST_HEAD (&urb_priv->pending);
 181         urb_priv->length = size;
 182         urb_priv->ed = ed;
 183
 184         /* allocate the TDs (deferring hash chain updates) */
 185         for (i = 0; i < size; i++) {
 186                 urb_priv->td [i] = td_alloc (ohci, mem_flags);
 187                 if (!urb_priv->td [i]) {
 188                         urb_priv->length = i;
 189                         urb_free_priv (ohci, urb_priv);
 190                         return -ENOMEM;
 191                 }
 192         }
 193
 194         spin_lock_irqsave (&ohci->lock, flags);
 195
 196         /* don't submit to a dead HC */
 197         if (!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags)) {
 198                 retval = -ENODEV;
 199                 goto fail;
 200         }
 201         if (!HC_IS_RUNNING(hcd->state)) {
 202                 retval = -ENODEV;
 203                 goto fail;
 204         }
 205
 206         /* in case of unlink-during-submit */
 207         spin_lock (&urb->lock);
 208         if (urb->status != -EINPROGRESS) {
 209                 spin_unlock (&urb->lock);
 210                 urb->hcpriv = urb_priv;
 211                 finish_urb (ohci, urb);
 212                 retval = 0;
 213                 goto fail;
 214         }
 215
 216         /* schedule the ed if needed */
 217         if (ed->state == ED_IDLE) {
 218                 retval = ed_schedule (ohci, ed);
 219                 if (retval < 0)
 220                         goto fail0;
 221                 if (ed->type == PIPE_ISOCHRONOUS) {
 222                         u16     frame = ohci_frame_no(ohci);
 223
 224                         /* delay a few frames before the first TD */
 225                         frame += max_t (u16, 8, ed->interval);
 226                         frame &= ~(ed->interval - 1);
 227                         frame |= ed->branch;
 228                         urb->start_frame = frame;
 229
 230                         /* yes, only URB_ISO_ASAP is supported, and
 231                          * urb->start_frame is never used as input.
 232                          */
 233                 }
 234         } else if (ed->type == PIPE_ISOCHRONOUS)
 235                 urb->start_frame = ed->last_iso + ed->interval;
 236
 237         /* fill the TDs and link them to the ed; and
 238          * enable that part of the schedule, if needed
 239          * and update count of queued periodic urbs
 240          */
 241         urb->hcpriv = urb_priv;
 242         td_submit_urb (ohci, urb);
 243
 244 fail0:
 245         spin_unlock (&urb->lock);
 246 fail:
 247         if (retval)
 248                 urb_free_priv (ohci, urb_priv);
 249         spin_unlock_irqrestore (&ohci->lock, flags);
 250         return retval;
 251 }
 252
 253 /*
 254  * decouple the URB from the HC queues (TDs, urb_priv); it's
 255  * already marked using urb->status.  reporting is always done
 256  * asynchronously, and we might be dealing with an urb that's
 257  * partially transferred, or an ED with other urbs being unlinked.
 258  */
 259 static int ohci_urb_dequeue (struct usb_hcd *hcd, struct urb *urb)
 260 {
 261         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
 262         unsigned long           flags;
 263
 264 #ifdef OHCI_VERBOSE_DEBUG
 265         urb_print (urb, "UNLINK", 1);
 266 #endif
 267
 268         spin_lock_irqsave (&ohci->lock, flags);
 269         if (HC_IS_RUNNING(hcd->state)) {
 270                 urb_priv_t  *urb_priv;
 271
 272                 /* Unless an IRQ completed the unlink while it was being
 273                  * handed to us, flag it for unlink and giveback, and force
 274                  * some upcoming INTR_SF to call finish_unlinks()
 275                  */
 276                 urb_priv = urb->hcpriv;
 277                 if (urb_priv) {
 278                         if (urb_priv->ed->state == ED_OPER)
 279                                 start_ed_unlink (ohci, urb_priv->ed);
 280                 }
 281         } else {
 282                 /*
 283                  * with HC dead, we won't respect hc queue pointers
 284                  * any more ... just clean up every urb's memory.
 285                  */
 286                 if (urb->hcpriv)
 287                         finish_urb (ohci, urb);
 288         }
 289         spin_unlock_irqrestore (&ohci->lock, flags);
 290         return 0;
 291 }
 292
 293 /*-------------------------------------------------------------------------*/
 294
 295 /* frees config/altsetting state for endpoints,
 296  * including ED memory, dummy TD, and bulk/intr data toggle
 297  */
 298
 299 static void
 300 ohci_endpoint_disable (struct usb_hcd *hcd, struct usb_host_endpoint *ep)
 301 {
 302         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
 303         unsigned long           flags;
 304         struct ed               *ed = ep->hcpriv;
 305         unsigned                limit = 1000;
 306
 307         /* ASSERT:  any requests/urbs are being unlinked */
 308         /* ASSERT:  nobody can be submitting urbs for this any more */
 309
 310         if (!ed)
 311                 return;
 312
 313 rescan:
 314         spin_lock_irqsave (&ohci->lock, flags);
 315
 316         if (!HC_IS_RUNNING (hcd->state)) {
 317 sanitize:
 318                 ed->state = ED_IDLE;
 319                 finish_unlinks (ohci, 0);
 320         }
 321
 322         switch (ed->state) {
 323         case ED_UNLINK:         /* wait for hw to finish? */
 324                 /* major IRQ delivery trouble loses INTR_SF too... */
 325                 if (limit-- == 0) {
 326                         ohci_warn (ohci, "IRQ INTR_SF lossage\n");
 327                         goto sanitize;
 328                 }
 329                 spin_unlock_irqrestore (&ohci->lock, flags);
 330                 schedule_timeout_uninterruptible(1);
 331                 goto rescan;
 332         case ED_IDLE:           /* fully unlinked */
 333                 if (list_empty (&ed->td_list)) {
 334                         td_free (ohci, ed->dummy);
 335                         ed_free (ohci, ed);
 336                         break;
 337                 }
 338                 /* else FALL THROUGH */
 339         default:
 340                 /* caller was supposed to have unlinked any requests;
 341                  * that's not our job.  can't recover; must leak ed.
 342                  */
 343                 ohci_err (ohci, "leak ed %p (#%02x) state %d%s\n",
 344                         ed, ep->desc.bEndpointAddress, ed->state,
 345                         list_empty (&ed->td_list) ? "" : " (has tds)");
 346                 td_free (ohci, ed->dummy);
 347                 break;
 348         }
 349         ep->hcpriv = NULL;
 350         spin_unlock_irqrestore (&ohci->lock, flags);
 351         return;
 352 }
 353
 354 static int ohci_get_frame (struct usb_hcd *hcd)
 355 {
 356         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
 357
 358         return ohci_frame_no(ohci);
 359 }
 360
 361 static void ohci_usb_reset (struct ohci_hcd *ohci)
 362 {
 363         ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
 364         ohci->hc_control &= OHCI_CTRL_RWC;
 365         ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
 366 }
 367
 368 /* ohci_shutdown forcibly disables IRQs and DMA, helping kexec and
 369  * other cases where the next software may expect clean state from the
 370  * "firmware".  this is bus-neutral, unlike shutdown() methods.
 371  */
 372 static void
 373 ohci_shutdown (struct usb_hcd *hcd)
 374 {
 375         struct ohci_hcd *ohci;
 376
 377         ohci = hcd_to_ohci (hcd);
 378         ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
 379         ohci_usb_reset (ohci);
 380         /* flush the writes */
 381         (void) ohci_readl (ohci, &ohci->regs->control);
 382 }
 383
 384 /*-------------------------------------------------------------------------*
 385  * HC functions
 386  *-------------------------------------------------------------------------*/
 387
 388 /* init memory, and kick BIOS/SMM off */
 389
 390 static int ohci_init (struct ohci_hcd *ohci)
 391 {
 392         int ret;
 393         struct usb_hcd *hcd = ohci_to_hcd(ohci);
 394
 395         disable (ohci);
 396         ohci->regs = hcd->regs;
 397
 398         /* REVISIT this BIOS handshake is now moved into PCI "quirks", and
 399          * was never needed for most non-PCI systems ... remove the code?
 400          */
 401
 402 #ifndef IR_DISABLE
 403         /* SMM owns the HC?  not for long! */
 404         if (!no_handshake && ohci_readl (ohci,
 405                                         &ohci->regs->control) & OHCI_CTRL_IR) {
 406                 u32 temp;
 407
 408                 ohci_dbg (ohci, "USB HC TakeOver from BIOS/SMM\n");
 409
 410                 /* this timeout is arbitrary.  we make it long, so systems
 411                  * depending on usb keyboards may be usable even if the
 412                  * BIOS/SMM code seems pretty broken.
 413                  */
 414                 temp = 500;     /* arbitrary: five seconds */
 415
 416                 ohci_writel (ohci, OHCI_INTR_OC, &ohci->regs->intrenable);
 417                 ohci_writel (ohci, OHCI_OCR, &ohci->regs->cmdstatus);
 418                 while (ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_IR) {
 419                         msleep (10);
 420                         if (--temp == 0) {
 421                                 ohci_err (ohci, "USB HC takeover failed!"
 422                                         "  (BIOS/SMM bug)\n");
 423                                 return -EBUSY;
 424                         }
 425                 }
 426                 ohci_usb_reset (ohci);
 427         }
 428 #endif
 429
 430         /* Disable HC interrupts */
 431         ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
 432
 433         /* flush the writes, and save key bits like RWC */
 434         if (ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_RWC)
 435                 ohci->hc_control |= OHCI_CTRL_RWC;
 436
 437         /* Read the number of ports unless overridden */
 438         if (ohci->num_ports == 0)
 439                 ohci->num_ports = roothub_a(ohci) & RH_A_NDP;
 440
 441         if (ohci->hcca)
 442                 return 0;
 443
 444         ohci->hcca = dma_alloc_coherent (hcd->self.controller,
 445                         sizeof *ohci->hcca, &ohci->hcca_dma, 0);
 446         if (!ohci->hcca)
 447                 return -ENOMEM;
 448
 449         if ((ret = ohci_mem_init (ohci)) < 0)
 450                 ohci_stop (hcd);
 451         else {
 452                 create_debug_files (ohci);
 453         }
 454
 455         return ret;
 456 }
 457
 458 /*-------------------------------------------------------------------------*/
 459
 460 /* Start an OHCI controller, set the BUS operational
 461  * resets USB and controller
 462  * enable interrupts
 463  */
 464 static int ohci_run (struct ohci_hcd *ohci)
 465 {
 466         u32                     mask, temp;
 467         int                     first = ohci->fminterval == 0;
 468         struct usb_hcd          *hcd = ohci_to_hcd(ohci);
 469
 470         disable (ohci);
 471
 472         /* boot firmware should have set this up (5.1.1.3.1) */
 473         if (first) {
 474
 475                 temp = ohci_readl (ohci, &ohci->regs->fminterval);
 476                 ohci->fminterval = temp & 0x3fff;
 477                 if (ohci->fminterval != FI)
 478                         ohci_dbg (ohci, "fminterval delta %d\n",
 479                                 ohci->fminterval - FI);
 480                 ohci->fminterval |= FSMP (ohci->fminterval) << 16;
 481                 /* also: power/overcurrent flags in roothub.a */
 482         }
 483
 484         /* Reset USB nearly "by the book".  RemoteWakeupConnected was
 485          * saved if boot firmware (BIOS/SMM/...) told us it's connected,
 486          * or if bus glue did the same (e.g. for PCI add-in cards with
 487          * PCI PM support).
 488          */
 489         if ((ohci->hc_control & OHCI_CTRL_RWC) != 0
 490                         && !device_may_wakeup(hcd->self.controller))
 491                 device_init_wakeup(hcd->self.controller, 1);
 492
 493         switch (ohci->hc_control & OHCI_CTRL_HCFS) {
 494         case OHCI_USB_OPER:
 495                 temp = 0;
 496                 break;
 497         case OHCI_USB_SUSPEND:
 498         case OHCI_USB_RESUME:
 499                 ohci->hc_control &= OHCI_CTRL_RWC;
 500                 ohci->hc_control |= OHCI_USB_RESUME;
 501                 temp = 10 /* msec wait */;
 502                 break;
 503         // case OHCI_USB_RESET:
 504         default:
 505                 ohci->hc_control &= OHCI_CTRL_RWC;
 506                 ohci->hc_control |= OHCI_USB_RESET;
 507                 temp = 50 /* msec wait */;
 508                 break;
 509         }
 510         ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
 511         // flush the writes
 512         (void) ohci_readl (ohci, &ohci->regs->control);
 513         msleep(temp);
 514         temp = roothub_a (ohci);
 515         if (!(temp & RH_A_NPS)) {
 516                 /* power down each port */
 517                 for (temp = 0; temp < ohci->num_ports; temp++)
 518                         ohci_writel (ohci, RH_PS_LSDA,
 519                                 &ohci->regs->roothub.portstatus [temp]);
 520         }
 521         // flush those writes
 522         (void) ohci_readl (ohci, &ohci->regs->control);
 523         memset (ohci->hcca, 0, sizeof (struct ohci_hcca));
 524
 525         /* 2msec timelimit here means no irqs/preempt */
 526         spin_lock_irq (&ohci->lock);
 527
 528 retry:
 529         /* HC Reset requires max 10 us delay */
 530         ohci_writel (ohci, OHCI_HCR,  &ohci->regs->cmdstatus);
 531         temp = 30;      /* ... allow extra time */
 532         while ((ohci_readl (ohci, &ohci->regs->cmdstatus) & OHCI_HCR) != 0) {
 533                 if (--temp == 0) {
 534                         spin_unlock_irq (&ohci->lock);
 535                         ohci_err (ohci, "USB HC reset timed out!\n");
 536                         return -1;
 537                 }
 538                 udelay (1);
 539         }
 540
 541         /* now we're in the SUSPEND state ... must go OPERATIONAL
 542          * within 2msec else HC enters RESUME
 543          *
 544          * ... but some hardware won't init fmInterval "by the book"
 545          * (SiS, OPTi ...), so reset again instead.  SiS doesn't need
 546          * this if we write fmInterval after we're OPERATIONAL.
 547          * Unclear about ALi, ServerWorks, and others ... this could
 548          * easily be a longstanding bug in chip init on Linux.
 549          */
 550         if (ohci->flags & OHCI_QUIRK_INITRESET) {
 551                 ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
 552                 // flush those writes
 553                 (void) ohci_readl (ohci, &ohci->regs->control);
 554         }
 555
 556         /* Tell the controller where the control and bulk lists are
 557          * The lists are empty now. */
 558         ohci_writel (ohci, 0, &ohci->regs->ed_controlhead);
 559         ohci_writel (ohci, 0, &ohci->regs->ed_bulkhead);
 560
 561         /* a reset clears this */
 562         ohci_writel (ohci, (u32) ohci->hcca_dma, &ohci->regs->hcca);
 563
 564         periodic_reinit (ohci);
 565
 566         /* some OHCI implementations are finicky about how they init.
 567          * bogus values here mean not even enumeration could work.
 568          */
 569         if ((ohci_readl (ohci, &ohci->regs->fminterval) & 0x3fff0000) == 0
 570                         || !ohci_readl (ohci, &ohci->regs->periodicstart)) {
 571                 if (!(ohci->flags & OHCI_QUIRK_INITRESET)) {
 572                         ohci->flags |= OHCI_QUIRK_INITRESET;
 573                         ohci_dbg (ohci, "enabling initreset quirk\n");
 574                         goto retry;
 575                 }
 576                 spin_unlock_irq (&ohci->lock);
 577                 ohci_err (ohci, "init err (%08x %04x)\n",
 578                         ohci_readl (ohci, &ohci->regs->fminterval),
 579                         ohci_readl (ohci, &ohci->regs->periodicstart));
 580                 return -EOVERFLOW;
 581         }
 582
 583         /* use rhsc irqs after khubd is fully initialized */
 584         hcd->poll_rh = 1;
 585         hcd->uses_new_polling = 1;
 586
 587         /* start controller operations */
 588         ohci->hc_control &= OHCI_CTRL_RWC;
 589         ohci->hc_control |= OHCI_CONTROL_INIT | OHCI_USB_OPER;
 590         ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
 591         hcd->state = HC_STATE_RUNNING;
 592
 593         /* wake on ConnectStatusChange, matching external hubs */
 594         ohci_writel (ohci, RH_HS_DRWE, &ohci->regs->roothub.status);
 595
 596         /* Choose the interrupts we care about now, others later on demand */
 597         mask = OHCI_INTR_INIT;
 598         ohci_writel (ohci, ~0, &ohci->regs->intrstatus);
 599         ohci_writel (ohci, mask, &ohci->regs->intrenable);
 600
 601         /* handle root hub init quirks ... */
 602         temp = roothub_a (ohci);
 603         temp &= ~(RH_A_PSM | RH_A_OCPM);
 604         if (ohci->flags & OHCI_QUIRK_SUPERIO) {
 605                 /* NSC 87560 and maybe others */
 606                 temp |= RH_A_NOCP;
 607                 temp &= ~(RH_A_POTPGT | RH_A_NPS);
 608                 ohci_writel (ohci, temp, &ohci->regs->roothub.a);
 609         } else if ((ohci->flags & OHCI_QUIRK_AMD756) || distrust_firmware) {
 610                 /* hub power always on; required for AMD-756 and some
 611                  * Mac platforms.  ganged overcurrent reporting, if any.
 612                  */
 613                 temp |= RH_A_NPS;
 614                 ohci_writel (ohci, temp, &ohci->regs->roothub.a);
 615         }
 616         ohci_writel (ohci, RH_HS_LPSC, &ohci->regs->roothub.status);
 617         ohci_writel (ohci, (temp & RH_A_NPS) ? 0 : RH_B_PPCM,
 618                                                 &ohci->regs->roothub.b);
 619         // flush those writes
 620         (void) ohci_readl (ohci, &ohci->regs->control);
 621
 622         ohci->next_statechange = jiffies + STATECHANGE_DELAY;
 623         spin_unlock_irq (&ohci->lock);
 624
 625         // POTPGT delay is bits 24-31, in 2 ms units.
 626         mdelay ((temp >> 23) & 0x1fe);
 627         hcd->state = HC_STATE_RUNNING;
 628
 629         ohci_dump (ohci, 1);
 630
 631         return 0;
 632 }
 633
 634 /*-------------------------------------------------------------------------*/
 635
 636 /* an interrupt happens */
 637
 638 static irqreturn_t ohci_irq (struct usb_hcd *hcd)
 639 {
 640         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
 641         struct ohci_regs __iomem *regs = ohci->regs;
 642         int                     ints;
 643
 644         /* we can eliminate a (slow) ohci_readl()
 645            if _only_ WDH caused this irq */
 646         if ((ohci->hcca->done_head != 0)
 647                         && ! (hc32_to_cpup (ohci, &ohci->hcca->done_head)
 648                                 & 0x01)) {
 649                 ints =  OHCI_INTR_WDH;
 650
 651         /* cardbus/... hardware gone before remove() */
 652         } else if ((ints = ohci_readl (ohci, &regs->intrstatus)) == ~(u32)0) {
 653                 disable (ohci);
 654                 ohci_dbg (ohci, "device removed!\n");
 655                 return IRQ_HANDLED;
 656
 657         /* interrupt for some other device? */
 658         } else if ((ints &= ohci_readl (ohci, &regs->intrenable)) == 0) {
 659                 return IRQ_NOTMINE;
 660         }
 661
 662         if (ints & OHCI_INTR_UE) {
 663                 disable (ohci);
 664                 ohci_err (ohci, "OHCI Unrecoverable Error, disabled\n");
 665                 // e.g. due to PCI Master/Target Abort
 666
 667                 ohci_dump (ohci, 1);
 668                 ohci_usb_reset (ohci);
 669         }
 670
 671         if (ints & OHCI_INTR_RHSC) {
 672                 ohci_vdbg(ohci, "rhsc\n");
 673                 ohci->next_statechange = jiffies + STATECHANGE_DELAY;
 674                 ohci_writel(ohci, OHCI_INTR_RD | OHCI_INTR_RHSC,
 675                                 &regs->intrstatus);
 676
 677                 /* NOTE: Vendors didn't always make the same implementation
 678                  * choices for RHSC.  Many followed the spec; RHSC triggers
 679                  * on an edge, like setting and maybe clearing a port status
 680                  * change bit.  With others it's level-triggered, active
 681                  * until khubd clears all the port status change bits.  We'll
 682                  * always disable it here and rely on polling until khubd
 683                  * re-enables it.
 684                  */
 685                 ohci_writel(ohci, OHCI_INTR_RHSC, &regs->intrdisable);
 686                 usb_hcd_poll_rh_status(hcd);
 687         }
 688
 689         /* For connect and disconnect events, we expect the controller
 690          * to turn on RHSC along with RD.  But for remote wakeup events
 691          * this might not happen.
 692          */
 693         else if (ints & OHCI_INTR_RD) {
 694                 ohci_vdbg(ohci, "resume detect\n");
 695                 ohci_writel(ohci, OHCI_INTR_RD, &regs->intrstatus);
 696                 hcd->poll_rh = 1;
 697                 if (ohci->autostop) {
 698                         spin_lock (&ohci->lock);
 699                         ohci_rh_resume (ohci);
 700                         spin_unlock (&ohci->lock);
 701                 } else
 702                         usb_hcd_resume_root_hub(hcd);
 703         }
 704
 705         if (ints & OHCI_INTR_WDH) {
 706                 if (HC_IS_RUNNING(hcd->state))
 707                         ohci_writel (ohci, OHCI_INTR_WDH, &regs->intrdisable);
 708                 spin_lock (&ohci->lock);
 709                 dl_done_list (ohci);
 710                 spin_unlock (&ohci->lock);
 711                 if (HC_IS_RUNNING(hcd->state))
 712                         ohci_writel (ohci, OHCI_INTR_WDH, &regs->intrenable);
 713         }
 714
 715         /* could track INTR_SO to reduce available PCI/... bandwidth */
 716
 717         /* handle any pending URB/ED unlinks, leaving INTR_SF enabled
 718          * when there's still unlinking to be done (next frame).
 719          */
 720         spin_lock (&ohci->lock);
 721         if (ohci->ed_rm_list)
 722                 finish_unlinks (ohci, ohci_frame_no(ohci));
 723         if ((ints & OHCI_INTR_SF) != 0 && !ohci->ed_rm_list
 724                         && HC_IS_RUNNING(hcd->state))
 725                 ohci_writel (ohci, OHCI_INTR_SF, &regs->intrdisable);
 726         spin_unlock (&ohci->lock);
 727
 728         if (HC_IS_RUNNING(hcd->state)) {
 729                 ohci_writel (ohci, ints, &regs->intrstatus);
 730                 ohci_writel (ohci, OHCI_INTR_MIE, &regs->intrenable);
 731                 // flush those writes
 732                 (void) ohci_readl (ohci, &ohci->regs->control);
 733         }
 734
 735         return IRQ_HANDLED;
 736 }
 737
 738 /*-------------------------------------------------------------------------*/
 739
 740 static void ohci_stop (struct usb_hcd *hcd)
 741 {
 742         struct ohci_hcd         *ohci = hcd_to_ohci (hcd);
 743
 744         ohci_dump (ohci, 1);
 745
 746         flush_scheduled_work();
 747
 748         ohci_usb_reset (ohci);
 749         ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
 750         free_irq(hcd->irq, hcd);
 751         hcd->irq = -1;
 752
 753         remove_debug_files (ohci);
 754         ohci_mem_cleanup (ohci);
 755         if (ohci->hcca) {
 756                 dma_free_coherent (hcd->self.controller,
 757                                 sizeof *ohci->hcca,
 758                                 ohci->hcca, ohci->hcca_dma);
 759                 ohci->hcca = NULL;
 760                 ohci->hcca_dma = 0;
 761         }
 762 }
 763
 764 /*-------------------------------------------------------------------------*/
 765
 766 /* must not be called from interrupt context */
 767
 768 #ifdef  CONFIG_PM
 769
 770 static int ohci_restart (struct ohci_hcd *ohci)
 771 {
 772         int temp;
 773         int i;
 774         struct urb_priv *priv;
 775
 776         /* mark any devices gone, so they do nothing till khubd disconnects.
 777          * recycle any "live" eds/tds (and urbs) right away.
 778          * later, khubd disconnect processing will recycle the other state,
 779          * (either as disconnect/reconnect, or maybe someday as a reset).
 780          */
 781         spin_lock_irq(&ohci->lock);
 782         disable (ohci);
 783         usb_root_hub_lost_power(ohci_to_hcd(ohci)->self.root_hub);
 784         if (!list_empty (&ohci->pending))
 785                 ohci_dbg(ohci, "abort schedule...\n");
 786         list_for_each_entry (priv, &ohci->pending, pending) {
 787                 struct urb      *urb = priv->td[0]->urb;
 788                 struct ed       *ed = priv->ed;
 789
 790                 switch (ed->state) {
 791                 case ED_OPER:
 792                         ed->state = ED_UNLINK;
 793                         ed->hwINFO |= cpu_to_hc32(ohci, ED_DEQUEUE);
 794                         ed_deschedule (ohci, ed);
 795
 796                         ed->ed_next = ohci->ed_rm_list;
 797                         ed->ed_prev = NULL;
 798                         ohci->ed_rm_list = ed;
 799                         /* FALLTHROUGH */
 800                 case ED_UNLINK:
 801                         break;
 802                 default:
 803                         ohci_dbg(ohci, "bogus ed %p state %d\n",
 804                                         ed, ed->state);
 805                 }
 806
 807                 spin_lock (&urb->lock);
 808                 urb->status = -ESHUTDOWN;
 809                 spin_unlock (&urb->lock);
 810         }
 811         finish_unlinks (ohci, 0);
 812         spin_unlock_irq(&ohci->lock);
 813
 814         /* paranoia, in case that didn't work: */
 815
 816         /* empty the interrupt branches */
 817         for (i = 0; i < NUM_INTS; i++) ohci->load [i] = 0;
 818         for (i = 0; i < NUM_INTS; i++) ohci->hcca->int_table [i] = 0;
 819
 820         /* no EDs to remove */
 821         ohci->ed_rm_list = NULL;
 822
 823         /* empty control and bulk lists */
 824         ohci->ed_controltail = NULL;
 825         ohci->ed_bulktail    = NULL;
 826
 827         if ((temp = ohci_run (ohci)) < 0) {
 828                 ohci_err (ohci, "can't restart, %d\n", temp);
 829                 return temp;
 830         } else {
 831                 /* here we "know" root ports should always stay powered,
 832                  * and that if we try to turn them back on the root hub
 833                  * will respond to CSC processing.
 834                  */
 835                 i = ohci->num_ports;
 836                 while (i--)
 837                         ohci_writel (ohci, RH_PS_PSS,
 838                                 &ohci->regs->roothub.portstatus [i]);
 839                 ohci_dbg (ohci, "restart complete\n");
 840         }
 841         return 0;
 842 }
 843 #endif
 844
 845 /*-------------------------------------------------------------------------*/
 846
 847 #define DRIVER_INFO DRIVER_VERSION " " DRIVER_DESC
 848
 849 MODULE_AUTHOR (DRIVER_AUTHOR);
 850 MODULE_DESCRIPTION (DRIVER_INFO);
 851 MODULE_LICENSE ("GPL");
 852
 853 #ifdef CONFIG_PCI
 854 #include "ohci-pci.c"
 855 #define PCI_DRIVER              ohci_pci_driver
 856 #endif
 857
 858 #ifdef CONFIG_SA1111
 859 #include "ohci-sa1111.c"
 860 #define SA1111_DRIVER           ohci_hcd_sa1111_driver
 861 #endif
 862
 863 #ifdef CONFIG_ARCH_S3C2410
 864 #include "ohci-s3c2410.c"
 865 #define PLATFORM_DRIVER         ohci_hcd_s3c2410_driver
 866 #endif
 867
 868 #ifdef CONFIG_ARCH_OMAP
 869 #include "ohci-omap.c"
 870 #define PLATFORM_DRIVER         ohci_hcd_omap_driver
 871 #endif
 872
 873 #ifdef CONFIG_ARCH_LH7A404
 874 #include "ohci-lh7a404.c"
 875 #define PLATFORM_DRIVER         ohci_hcd_lh7a404_driver
 876 #endif
 877
 878 #ifdef CONFIG_PXA27x
 879 #include "ohci-pxa27x.c"
 880 #define PLATFORM_DRIVER         ohci_hcd_pxa27x_driver
 881 #endif
 882
 883 #ifdef CONFIG_ARCH_EP93XX
 884 #include "ohci-ep93xx.c"
 885 #define PLATFORM_DRIVER         ohci_hcd_ep93xx_driver
 886 #endif
 887
 888 #ifdef CONFIG_SOC_AU1X00
 889 #include "ohci-au1xxx.c"
 890 #define PLATFORM_DRIVER         ohci_hcd_au1xxx_driver
 891 #endif
 892
 893 #ifdef CONFIG_PNX8550
 894 #include "ohci-pnx8550.c"
 895 #define PLATFORM_DRIVER         ohci_hcd_pnx8550_driver
 896 #endif
 897
 898 #ifdef CONFIG_USB_OHCI_HCD_PPC_SOC
 899 #include "ohci-ppc-soc.c"
 900 #define PLATFORM_DRIVER         ohci_hcd_ppc_soc_driver
 901 #endif
 902
 903 #ifdef CONFIG_ARCH_AT91
 904 #include "ohci-at91.c"
 905 #define PLATFORM_DRIVER         ohci_hcd_at91_driver
 906 #endif
 907
 908 #ifdef CONFIG_ARCH_PNX4008
 909 #include "ohci-pnx4008.c"
 910 #define PLATFORM_DRIVER         usb_hcd_pnx4008_driver
 911 #endif
 912
 913
 914 #ifdef CONFIG_USB_OHCI_HCD_PPC_OF
 915 #include "ohci-ppc-of.c"
 916 #define OF_PLATFORM_DRIVER      ohci_hcd_ppc_of_driver
 917 #endif
 918
 919 #ifdef CONFIG_PPC_PS3
 920 #include "ohci-ps3.c"
 921 #define PS3_SYSTEM_BUS_DRIVER   ps3_ohci_sb_driver
 922 #endif
 923
 924 #if     !defined(PCI_DRIVER) &&         \
 925         !defined(PLATFORM_DRIVER) &&    \
 926         !defined(OF_PLATFORM_DRIVER) && \
 927         !defined(SA1111_DRIVER) &&      \
 928         !defined(PS3_SYSTEM_BUS_DRIVER)
 929 #error "missing bus glue for ohci-hcd"
 930 #endif
 931
 932 static int __init ohci_hcd_mod_init(void)
 933 {
 934         int retval = 0;
 935
 936         if (usb_disabled())
 937                 return -ENODEV;
 938
 939         printk (KERN_DEBUG "%s: " DRIVER_INFO "\n", hcd_name);
 940         pr_debug ("%s: block sizes: ed %Zd td %Zd\n", hcd_name,
 941                 sizeof (struct ed), sizeof (struct td));
 942
 943 #ifdef PS3_SYSTEM_BUS_DRIVER
 944         if (firmware_has_feature(FW_FEATURE_PS3_LV1)) {
 945                 retval = ps3_system_bus_driver_register(
 946                                 &PS3_SYSTEM_BUS_DRIVER);
 947                 if (retval < 0)
 948                         goto error_ps3;
 949         }
 950 #endif
 951
 952 #ifdef PLATFORM_DRIVER
 953         retval = platform_driver_register(&PLATFORM_DRIVER);
 954         if (retval < 0)
 955                 goto error_platform;
 956 #endif
 957
 958 #ifdef OF_PLATFORM_DRIVER
 959         retval = of_register_platform_driver(&OF_PLATFORM_DRIVER);
 960         if (retval < 0)
 961                 goto error_of_platform;
 962 #endif
 963
 964 #ifdef SA1111_DRIVER
 965         retval = sa1111_driver_register(&SA1111_DRIVER);
 966         if (retval < 0)
 967                 goto error_sa1111;
 968 #endif
 969
 970 #ifdef PCI_DRIVER
 971         retval = pci_register_driver(&PCI_DRIVER);
 972         if (retval < 0)
 973                 goto error_pci;
 974 #endif
 975
 976         return retval;
 977
 978         /* Error path */
 979 #ifdef PCI_DRIVER
 980  error_pci:
 981 #endif
 982 #ifdef SA1111_DRIVER
 983         sa1111_driver_unregister(&SA1111_DRIVER);
 984  error_sa1111:
 985 #endif
 986 #ifdef OF_PLATFORM_DRIVER
 987         of_unregister_platform_driver(&OF_PLATFORM_DRIVER);
 988  error_of_platform:
 989 #endif
 990 #ifdef PLATFORM_DRIVER
 991         platform_driver_unregister(&PLATFORM_DRIVER);
 992  error_platform:
 993 #endif
 994 #ifdef PS3_SYSTEM_BUS_DRIVER
 995         if (firmware_has_feature(FW_FEATURE_PS3_LV1))
 996                 ps3_system_bus_driver_unregister(&PS3_SYSTEM_BUS_DRIVER);
 997  error_ps3:
 998 #endif
 999         return retval;
1000 }
1001 module_init(ohci_hcd_mod_init);
1002
1003 static void __exit ohci_hcd_mod_exit(void)
1004 {
1005 #ifdef PCI_DRIVER
1006         pci_unregister_driver(&PCI_DRIVER);
1007 #endif
1008 #ifdef SA1111_DRIVER
1009         sa1111_driver_unregister(&SA1111_DRIVER);
1010 #endif
1011 #ifdef OF_PLATFORM_DRIVER
1012         of_unregister_platform_driver(&OF_PLATFORM_DRIVER);
1013 #endif
1014 #ifdef PLATFORM_DRIVER
1015         platform_driver_unregister(&PLATFORM_DRIVER);
1016 #endif
1017 #ifdef PS3_SYSTEM_BUS_DRIVER
1018         if (firmware_has_feature(FW_FEATURE_PS3_LV1))
1019                 ps3_system_bus_driver_unregister(&PS3_SYSTEM_BUS_DRIVER);
1020 #endif
1021 }
1022 module_exit(ohci_hcd_mod_exit);
1023