2 * OHCI HCD (Host Controller Driver) for USB.
4 * Copyright (C) 2004 SAN People (Pty) Ltd.
5 * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
9 * Based on fragments of 2.4 driver by Rick Bronson.
10 * Based on ohci-omap.c
12 * This file is licenced under the GPL.
15 #include <linux/clk.h>
16 #include <linux/platform_device.h>
18 #include <mach/hardware.h>
21 #include <mach/board.h>
24 #ifndef CONFIG_ARCH_AT91
25 #error "CONFIG_ARCH_AT91 must be defined."
28 /* interface and function clocks; sometimes also an AHB clock */
29 static struct clk *iclk, *fclk, *hclk;
32 extern int usb_disabled(void);
34 /*-------------------------------------------------------------------------*/
36 static void at91_start_clock(void)
44 static void at91_stop_clock(void)
52 static void at91_start_hc(struct platform_device *pdev)
54 struct usb_hcd *hcd = platform_get_drvdata(pdev);
55 struct ohci_regs __iomem *regs = hcd->regs;
57 dev_dbg(&pdev->dev, "start\n");
60 * Start the USB clocks.
65 * The USB host controller must remain in reset.
67 writel(0, ®s->control);
70 static void at91_stop_hc(struct platform_device *pdev)
72 struct usb_hcd *hcd = platform_get_drvdata(pdev);
73 struct ohci_regs __iomem *regs = hcd->regs;
75 dev_dbg(&pdev->dev, "stop\n");
78 * Put the USB host controller into reset.
80 writel(0, ®s->control);
83 * Stop the USB clocks.
89 /*-------------------------------------------------------------------------*/
91 static void usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *);
93 /* configure so an HC device and id are always provided */
94 /* always called with process context; sleeping is OK */
98 * usb_hcd_at91_probe - initialize AT91-based HCDs
99 * Context: !in_interrupt()
101 * Allocates basic resources for this USB host controller, and
102 * then invokes the start() method for the HCD associated with it
103 * through the hotplug entry's driver_data.
105 static int usb_hcd_at91_probe(const struct hc_driver *driver,
106 struct platform_device *pdev)
109 struct usb_hcd *hcd = NULL;
111 if (pdev->num_resources != 2) {
112 pr_debug("hcd probe: invalid num_resources");
116 if ((pdev->resource[0].flags != IORESOURCE_MEM)
117 || (pdev->resource[1].flags != IORESOURCE_IRQ)) {
118 pr_debug("hcd probe: invalid resource type\n");
122 hcd = usb_create_hcd(driver, &pdev->dev, "at91");
125 hcd->rsrc_start = pdev->resource[0].start;
126 hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
128 if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
129 pr_debug("request_mem_region failed\n");
134 hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
136 pr_debug("ioremap failed\n");
141 iclk = clk_get(&pdev->dev, "ohci_clk");
142 fclk = clk_get(&pdev->dev, "uhpck");
143 hclk = clk_get(&pdev->dev, "hclk");
146 ohci_hcd_init(hcd_to_ohci(hcd));
148 retval = usb_add_hcd(hcd, pdev->resource[1].start, IRQF_SHARED);
162 release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
170 /* may be called with controller, bus, and devices active */
173 * usb_hcd_at91_remove - shutdown processing for AT91-based HCDs
174 * @dev: USB Host Controller being removed
175 * Context: !in_interrupt()
177 * Reverses the effect of usb_hcd_at91_probe(), first invoking
178 * the HCD's stop() method. It is always called from a thread
179 * context, "rmmod" or something similar.
182 static void usb_hcd_at91_remove(struct usb_hcd *hcd,
183 struct platform_device *pdev)
188 release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
194 fclk = iclk = hclk = NULL;
196 dev_set_drvdata(&pdev->dev, NULL);
199 /*-------------------------------------------------------------------------*/
202 ohci_at91_start (struct usb_hcd *hcd)
204 struct at91_usbh_data *board = hcd->self.controller->platform_data;
205 struct ohci_hcd *ohci = hcd_to_ohci (hcd);
208 if ((ret = ohci_init(ohci)) < 0)
211 ohci->num_ports = board->ports;
213 if ((ret = ohci_run(ohci)) < 0) {
214 err("can't start %s", hcd->self.bus_name);
221 static void ohci_at91_usb_set_power(struct at91_usbh_data *pdata, int port, int enable)
223 if (port < 0 || port >= 2)
226 gpio_set_value(pdata->vbus_pin[port], !pdata->vbus_pin_inverted ^ enable);
229 static int ohci_at91_usb_get_power(struct at91_usbh_data *pdata, int port)
231 if (port < 0 || port >= 2)
234 return gpio_get_value(pdata->vbus_pin[port]) ^ !pdata->vbus_pin_inverted;
238 * Update the status data from the hub with the over-current indicator change.
240 static int ohci_at91_hub_status_data(struct usb_hcd *hcd, char *buf)
242 struct at91_usbh_data *pdata = hcd->self.controller->platform_data;
243 int length = ohci_hub_status_data(hcd, buf);
246 for (port = 0; port < ARRAY_SIZE(pdata->overcurrent_pin); port++) {
247 if (pdata->overcurrent_changed[port]) {
250 buf[0] |= 1 << (port + 1);
258 * Look at the control requests to the root hub and see if we need to override.
260 static int ohci_at91_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
261 u16 wIndex, char *buf, u16 wLength)
263 struct at91_usbh_data *pdata = hcd->self.controller->platform_data;
264 struct usb_hub_descriptor *desc;
266 u32 *data = (u32 *)buf;
268 dev_dbg(hcd->self.controller,
269 "ohci_at91_hub_control(%p,0x%04x,0x%04x,0x%04x,%p,%04x)\n",
270 hcd, typeReq, wValue, wIndex, buf, wLength);
274 if (wValue == USB_PORT_FEAT_POWER) {
275 dev_dbg(hcd->self.controller, "SetPortFeat: POWER\n");
276 ohci_at91_usb_set_power(pdata, wIndex - 1, 1);
281 case ClearPortFeature:
283 case USB_PORT_FEAT_C_OVER_CURRENT:
284 dev_dbg(hcd->self.controller,
285 "ClearPortFeature: C_OVER_CURRENT\n");
287 if (wIndex == 1 || wIndex == 2) {
288 pdata->overcurrent_changed[wIndex-1] = 0;
289 pdata->overcurrent_status[wIndex-1] = 0;
294 case USB_PORT_FEAT_OVER_CURRENT:
295 dev_dbg(hcd->self.controller,
296 "ClearPortFeature: OVER_CURRENT\n");
298 if (wIndex == 1 || wIndex == 2) {
299 pdata->overcurrent_status[wIndex-1] = 0;
304 case USB_PORT_FEAT_POWER:
305 dev_dbg(hcd->self.controller,
306 "ClearPortFeature: POWER\n");
308 if (wIndex == 1 || wIndex == 2) {
309 ohci_at91_usb_set_power(pdata, wIndex - 1, 0);
316 ret = ohci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength);
321 case GetHubDescriptor:
323 /* update the hub's descriptor */
325 desc = (struct usb_hub_descriptor *)buf;
327 dev_dbg(hcd->self.controller, "wHubCharacteristics 0x%04x\n",
328 desc->wHubCharacteristics);
330 /* remove the old configurations for power-switching, and
331 * over-current protection, and insert our new configuration
334 desc->wHubCharacteristics &= ~cpu_to_le16(HUB_CHAR_LPSM);
335 desc->wHubCharacteristics |= cpu_to_le16(0x0001);
337 if (pdata->overcurrent_supported) {
338 desc->wHubCharacteristics &= ~cpu_to_le16(HUB_CHAR_OCPM);
339 desc->wHubCharacteristics |= cpu_to_le16(0x0008|0x0001);
342 dev_dbg(hcd->self.controller, "wHubCharacteristics after 0x%04x\n",
343 desc->wHubCharacteristics);
348 /* check port status */
350 dev_dbg(hcd->self.controller, "GetPortStatus(%d)\n", wIndex);
352 if (wIndex == 1 || wIndex == 2) {
353 if (! ohci_at91_usb_get_power(pdata, wIndex-1)) {
354 *data &= ~cpu_to_le32(RH_PS_PPS);
357 if (pdata->overcurrent_changed[wIndex-1]) {
358 *data |= cpu_to_le32(RH_PS_OCIC);
361 if (pdata->overcurrent_status[wIndex-1]) {
362 *data |= cpu_to_le32(RH_PS_POCI);
371 /*-------------------------------------------------------------------------*/
373 static const struct hc_driver ohci_at91_hc_driver = {
374 .description = hcd_name,
375 .product_desc = "AT91 OHCI",
376 .hcd_priv_size = sizeof(struct ohci_hcd),
379 * generic hardware linkage
382 .flags = HCD_USB11 | HCD_MEMORY,
385 * basic lifecycle operations
387 .start = ohci_at91_start,
389 .shutdown = ohci_shutdown,
392 * managing i/o requests and associated device resources
394 .urb_enqueue = ohci_urb_enqueue,
395 .urb_dequeue = ohci_urb_dequeue,
396 .endpoint_disable = ohci_endpoint_disable,
401 .get_frame_number = ohci_get_frame,
406 .hub_status_data = ohci_at91_hub_status_data,
407 .hub_control = ohci_at91_hub_control,
409 .bus_suspend = ohci_bus_suspend,
410 .bus_resume = ohci_bus_resume,
412 .start_port_reset = ohci_start_port_reset,
415 /*-------------------------------------------------------------------------*/
417 static irqreturn_t ohci_hcd_at91_overcurrent_irq(int irq, void *data)
419 struct platform_device *pdev = data;
420 struct at91_usbh_data *pdata = pdev->dev.platform_data;
423 /* From the GPIO notifying the over-current situation, find
424 * out the corresponding port */
425 gpio = irq_to_gpio(irq);
426 for (port = 0; port < ARRAY_SIZE(pdata->overcurrent_pin); port++) {
427 if (pdata->overcurrent_pin[port] == gpio)
431 if (port == ARRAY_SIZE(pdata->overcurrent_pin)) {
432 dev_err(& pdev->dev, "overcurrent interrupt from unknown GPIO\n");
436 val = gpio_get_value(gpio);
438 /* When notified of an over-current situation, disable power
439 on the corresponding port, and mark this port in
442 ohci_at91_usb_set_power(pdata, port, 0);
443 pdata->overcurrent_status[port] = 1;
444 pdata->overcurrent_changed[port] = 1;
447 dev_dbg(& pdev->dev, "overcurrent situation %s\n",
448 val ? "exited" : "notified");
453 /*-------------------------------------------------------------------------*/
455 static int ohci_hcd_at91_drv_probe(struct platform_device *pdev)
457 struct at91_usbh_data *pdata = pdev->dev.platform_data;
461 for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
462 if (pdata->vbus_pin[i] <= 0)
464 gpio_request(pdata->vbus_pin[i], "ohci_vbus");
465 ohci_at91_usb_set_power(pdata, i, 1);
468 for (i = 0; i < ARRAY_SIZE(pdata->overcurrent_pin); i++) {
471 if (pdata->overcurrent_pin[i] <= 0)
473 gpio_request(pdata->overcurrent_pin[i], "ohci_overcurrent");
475 ret = request_irq(gpio_to_irq(pdata->overcurrent_pin[i]),
476 ohci_hcd_at91_overcurrent_irq,
477 IRQF_SHARED, "ohci_overcurrent", pdev);
479 gpio_free(pdata->overcurrent_pin[i]);
480 dev_warn(& pdev->dev, "cannot get GPIO IRQ for overcurrent\n");
485 device_init_wakeup(&pdev->dev, 1);
486 return usb_hcd_at91_probe(&ohci_at91_hc_driver, pdev);
489 static int ohci_hcd_at91_drv_remove(struct platform_device *pdev)
491 struct at91_usbh_data *pdata = pdev->dev.platform_data;
495 for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
496 if (pdata->vbus_pin[i] <= 0)
498 ohci_at91_usb_set_power(pdata, i, 0);
499 gpio_free(pdata->vbus_pin[i]);
502 for (i = 0; i < ARRAY_SIZE(pdata->overcurrent_pin); i++) {
503 if (pdata->overcurrent_pin[i] <= 0)
505 free_irq(gpio_to_irq(pdata->overcurrent_pin[i]), pdev);
506 gpio_free(pdata->overcurrent_pin[i]);
510 device_init_wakeup(&pdev->dev, 0);
511 usb_hcd_at91_remove(platform_get_drvdata(pdev), pdev);
518 ohci_hcd_at91_drv_suspend(struct platform_device *pdev, pm_message_t mesg)
520 struct usb_hcd *hcd = platform_get_drvdata(pdev);
521 struct ohci_hcd *ohci = hcd_to_ohci(hcd);
523 if (device_may_wakeup(&pdev->dev))
524 enable_irq_wake(hcd->irq);
527 * The integrated transceivers seem unable to notice disconnect,
528 * reconnect, or wakeup without the 48 MHz clock active. so for
529 * correctness, always discard connection state (using reset).
531 * REVISIT: some boards will be able to turn VBUS off...
533 if (at91_suspend_entering_slow_clock()) {
534 ohci_usb_reset (ohci);
535 /* flush the writes */
536 (void) ohci_readl (ohci, &ohci->regs->control);
543 static int ohci_hcd_at91_drv_resume(struct platform_device *pdev)
545 struct usb_hcd *hcd = platform_get_drvdata(pdev);
547 if (device_may_wakeup(&pdev->dev))
548 disable_irq_wake(hcd->irq);
553 ohci_finish_controller_resume(hcd);
557 #define ohci_hcd_at91_drv_suspend NULL
558 #define ohci_hcd_at91_drv_resume NULL
561 MODULE_ALIAS("platform:at91_ohci");
563 static struct platform_driver ohci_hcd_at91_driver = {
564 .probe = ohci_hcd_at91_drv_probe,
565 .remove = ohci_hcd_at91_drv_remove,
566 .shutdown = usb_hcd_platform_shutdown,
567 .suspend = ohci_hcd_at91_drv_suspend,
568 .resume = ohci_hcd_at91_drv_resume,
571 .owner = THIS_MODULE,