drivers/usb/gadget/pxa25x_udc.c

   1 /*
   2  * Intel PXA25x and IXP4xx on-chip full speed USB device controllers
   3  *
   4  * Copyright (C) 2002 Intrinsyc, Inc. (Frank Becker)
   5  * Copyright (C) 2003 Robert Schwebel, Pengutronix
   6  * Copyright (C) 2003 Benedikt Spranger, Pengutronix
   7  * Copyright (C) 2003 David Brownell
   8  * Copyright (C) 2003 Joshua Wise
   9  *
  10  * This program is free software; you can redistribute it and/or modify
  11  * it under the terms of the GNU General Public License as published by
  12  * the Free Software Foundation; either version 2 of the License, or
  13  * (at your option) any later version.
  14  */
  15
  16 /* #define VERBOSE_DEBUG */
  17
  18 #include <linux/device.h>
  19 #include <linux/module.h>
  20 #include <linux/kernel.h>
  21 #include <linux/ioport.h>
  22 #include <linux/types.h>
  23 #include <linux/errno.h>
  24 #include <linux/err.h>
  25 #include <linux/delay.h>
  26 #include <linux/slab.h>
  27 #include <linux/init.h>
  28 #include <linux/timer.h>
  29 #include <linux/list.h>
  30 #include <linux/interrupt.h>
  31 #include <linux/mm.h>
  32 #include <linux/platform_device.h>
  33 #include <linux/dma-mapping.h>
  34 #include <linux/irq.h>
  35 #include <linux/clk.h>
  36 #include <linux/err.h>
  37 #include <linux/seq_file.h>
  38 #include <linux/debugfs.h>
  39 #include <linux/io.h>
  40 #include <linux/prefetch.h>
  41
  42 #include <asm/byteorder.h>
  43 #include <asm/dma.h>
  44 #include <asm/gpio.h>
  45 #include <asm/mach-types.h>
  46 #include <asm/unaligned.h>
  47
  48 #include <linux/usb/ch9.h>
  49 #include <linux/usb/gadget.h>
  50 #include <linux/usb/otg.h>
  51
  52 /*
  53  * This driver is PXA25x only.  Grab the right register definitions.
  54  */
  55 #ifdef CONFIG_ARCH_PXA
  56 #include <mach/pxa25x-udc.h>
  57 #endif
  58
  59 #ifdef CONFIG_ARCH_LUBBOCK
  60 #include <mach/lubbock.h>
  61 #endif
  62
  63 #include <asm/mach/udc_pxa2xx.h>
  64
  65
  66 /*
  67  * This driver handles the USB Device Controller (UDC) in Intel's PXA 25x
  68  * series processors.  The UDC for the IXP 4xx series is very similar.
  69  * There are fifteen endpoints, in addition to ep0.
  70  *
  71  * Such controller drivers work with a gadget driver.  The gadget driver
  72  * returns descriptors, implements configuration and data protocols used
  73  * by the host to interact with this device, and allocates endpoints to
  74  * the different protocol interfaces.  The controller driver virtualizes
  75  * usb hardware so that the gadget drivers will be more portable.
  76  *
  77  * This UDC hardware wants to implement a bit too much USB protocol, so
  78  * it constrains the sorts of USB configuration change events that work.
  79  * The errata for these chips are misleading; some "fixed" bugs from
  80  * pxa250 a0/a1 b0/b1/b2 sure act like they're still there.
  81  *
  82  * Note that the UDC hardware supports DMA (except on IXP) but that's
  83  * not used here.  IN-DMA (to host) is simple enough, when the data is
  84  * suitably aligned (16 bytes) ... the network stack doesn't do that,
  85  * other software can.  OUT-DMA is buggy in most chip versions, as well
  86  * as poorly designed (data toggle not automatic).  So this driver won't
  87  * bother using DMA.  (Mostly-working IN-DMA support was available in
  88  * kernels before 2.6.23, but was never enabled or well tested.)
  89  */
  90
  91 #define DRIVER_VERSION  "30-June-2007"
  92 #define DRIVER_DESC     "PXA 25x USB Device Controller driver"
  93
  94
  95 static const char driver_name [] = "pxa25x_udc";
  96
  97 static const char ep0name [] = "ep0";
  98
  99
 100 #ifdef CONFIG_ARCH_IXP4XX
 101
 102 /* cpu-specific register addresses are compiled in to this code */
 103 #ifdef CONFIG_ARCH_PXA
 104 #error "Can't configure both IXP and PXA"
 105 #endif
 106
 107 /* IXP doesn't yet support <linux/clk.h> */
 108 #define clk_get(dev,name)       NULL
 109 #define clk_enable(clk)         do { } while (0)
 110 #define clk_disable(clk)        do { } while (0)
 111 #define clk_put(clk)            do { } while (0)
 112
 113 #endif
 114
 115 #include "pxa25x_udc.h"
 116
 117
 118 #ifdef  CONFIG_USB_PXA25X_SMALL
 119 #define SIZE_STR        " (small)"
 120 #else
 121 #define SIZE_STR        ""
 122 #endif
 123
 124 /* ---------------------------------------------------------------------------
 125  *      endpoint related parts of the api to the usb controller hardware,
 126  *      used by gadget driver; and the inner talker-to-hardware core.
 127  * ---------------------------------------------------------------------------
 128  */
 129
 130 static void pxa25x_ep_fifo_flush (struct usb_ep *ep);
 131 static void nuke (struct pxa25x_ep *, int status);
 132
 133 /* one GPIO should control a D+ pullup, so host sees this device (or not) */
 134 static void pullup_off(void)
 135 {
 136         struct pxa2xx_udc_mach_info             *mach = the_controller->mach;
 137         int off_level = mach->gpio_pullup_inverted;
 138
 139         if (gpio_is_valid(mach->gpio_pullup))
 140                 gpio_set_value(mach->gpio_pullup, off_level);
 141         else if (mach->udc_command)
 142                 mach->udc_command(PXA2XX_UDC_CMD_DISCONNECT);
 143 }
 144
 145 static void pullup_on(void)
 146 {
 147         struct pxa2xx_udc_mach_info             *mach = the_controller->mach;
 148         int on_level = !mach->gpio_pullup_inverted;
 149
 150         if (gpio_is_valid(mach->gpio_pullup))
 151                 gpio_set_value(mach->gpio_pullup, on_level);
 152         else if (mach->udc_command)
 153                 mach->udc_command(PXA2XX_UDC_CMD_CONNECT);
 154 }
 155
 156 static void pio_irq_enable(int bEndpointAddress)
 157 {
 158         bEndpointAddress &= 0xf;
 159         if (bEndpointAddress < 8)
 160                 UICR0 &= ~(1 << bEndpointAddress);
 161         else {
 162                 bEndpointAddress -= 8;
 163                 UICR1 &= ~(1 << bEndpointAddress);
 164         }
 165 }
 166
 167 static void pio_irq_disable(int bEndpointAddress)
 168 {
 169         bEndpointAddress &= 0xf;
 170         if (bEndpointAddress < 8)
 171                 UICR0 |= 1 << bEndpointAddress;
 172         else {
 173                 bEndpointAddress -= 8;
 174                 UICR1 |= 1 << bEndpointAddress;
 175         }
 176 }
 177
 178 /* The UDCCR reg contains mask and interrupt status bits,
 179  * so using '|=' isn't safe as it may ack an interrupt.
 180  */
 181 #define UDCCR_MASK_BITS         (UDCCR_REM | UDCCR_SRM | UDCCR_UDE)
 182
 183 static inline void udc_set_mask_UDCCR(int mask)
 184 {
 185         UDCCR = (UDCCR & UDCCR_MASK_BITS) | (mask & UDCCR_MASK_BITS);
 186 }
 187
 188 static inline void udc_clear_mask_UDCCR(int mask)
 189 {
 190         UDCCR = (UDCCR & UDCCR_MASK_BITS) & ~(mask & UDCCR_MASK_BITS);
 191 }
 192
 193 static inline void udc_ack_int_UDCCR(int mask)
 194 {
 195         /* udccr contains the bits we dont want to change */
 196         __u32 udccr = UDCCR & UDCCR_MASK_BITS;
 197
 198         UDCCR = udccr | (mask & ~UDCCR_MASK_BITS);
 199 }
 200
 201 /*
 202  * endpoint enable/disable
 203  *
 204  * we need to verify the descriptors used to enable endpoints.  since pxa25x
 205  * endpoint configurations are fixed, and are pretty much always enabled,
 206  * there's not a lot to manage here.
 207  *
 208  * because pxa25x can't selectively initialize bulk (or interrupt) endpoints,
 209  * (resetting endpoint halt and toggle), SET_INTERFACE is unusable except
 210  * for a single interface (with only the default altsetting) and for gadget
 211  * drivers that don't halt endpoints (not reset by set_interface).  that also
 212  * means that if you use ISO, you must violate the USB spec rule that all
 213  * iso endpoints must be in non-default altsettings.
 214  */
 215 static int pxa25x_ep_enable (struct usb_ep *_ep,
 216                 const struct usb_endpoint_descriptor *desc)
 217 {
 218         struct pxa25x_ep        *ep;
 219         struct pxa25x_udc       *dev;
 220
 221         ep = container_of (_ep, struct pxa25x_ep, ep);
 222         if (!_ep || !desc || _ep->name == ep0name
 223                         || desc->bDescriptorType != USB_DT_ENDPOINT
 224                         || ep->bEndpointAddress != desc->bEndpointAddress
 225                         || ep->fifo_size < usb_endpoint_maxp (desc)) {
 226                 DMSG("%s, bad ep or descriptor\n", __func__);
 227                 return -EINVAL;
 228         }
 229
 230         /* xfer types must match, except that interrupt ~= bulk */
 231         if (ep->bmAttributes != desc->bmAttributes
 232                         && ep->bmAttributes != USB_ENDPOINT_XFER_BULK
 233                         && desc->bmAttributes != USB_ENDPOINT_XFER_INT) {
 234                 DMSG("%s, %s type mismatch\n", __func__, _ep->name);
 235                 return -EINVAL;
 236         }
 237
 238         /* hardware _could_ do smaller, but driver doesn't */
 239         if ((desc->bmAttributes == USB_ENDPOINT_XFER_BULK
 240                                 && usb_endpoint_maxp (desc)
 241                                                 != BULK_FIFO_SIZE)
 242                         || !desc->wMaxPacketSize) {
 243                 DMSG("%s, bad %s maxpacket\n", __func__, _ep->name);
 244                 return -ERANGE;
 245         }
 246
 247         dev = ep->dev;
 248         if (!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN) {
 249                 DMSG("%s, bogus device state\n", __func__);
 250                 return -ESHUTDOWN;
 251         }
 252
 253         ep->ep.desc = desc;
 254         ep->stopped = 0;
 255         ep->pio_irqs = 0;
 256         ep->ep.maxpacket = usb_endpoint_maxp (desc);
 257
 258         /* flush fifo (mostly for OUT buffers) */
 259         pxa25x_ep_fifo_flush (_ep);
 260
 261         /* ... reset halt state too, if we could ... */
 262
 263         DBG(DBG_VERBOSE, "enabled %s\n", _ep->name);
 264         return 0;
 265 }
 266
 267 static int pxa25x_ep_disable (struct usb_ep *_ep)
 268 {
 269         struct pxa25x_ep        *ep;
 270         unsigned long           flags;
 271
 272         ep = container_of (_ep, struct pxa25x_ep, ep);
 273         if (!_ep || !ep->ep.desc) {
 274                 DMSG("%s, %s not enabled\n", __func__,
 275                         _ep ? ep->ep.name : NULL);
 276                 return -EINVAL;
 277         }
 278         local_irq_save(flags);
 279
 280         nuke (ep, -ESHUTDOWN);
 281
 282         /* flush fifo (mostly for IN buffers) */
 283         pxa25x_ep_fifo_flush (_ep);
 284
 285         ep->ep.desc = NULL;
 286         ep->stopped = 1;
 287
 288         local_irq_restore(flags);
 289         DBG(DBG_VERBOSE, "%s disabled\n", _ep->name);
 290         return 0;
 291 }
 292
 293 /*-------------------------------------------------------------------------*/
 294
 295 /* for the pxa25x, these can just wrap kmalloc/kfree.  gadget drivers
 296  * must still pass correctly initialized endpoints, since other controller
 297  * drivers may care about how it's currently set up (dma issues etc).
 298  */
 299
 300 /*
 301  *      pxa25x_ep_alloc_request - allocate a request data structure
 302  */
 303 static struct usb_request *
 304 pxa25x_ep_alloc_request (struct usb_ep *_ep, gfp_t gfp_flags)
 305 {
 306         struct pxa25x_request *req;
 307
 308         req = kzalloc(sizeof(*req), gfp_flags);
 309         if (!req)
 310                 return NULL;
 311
 312         INIT_LIST_HEAD (&req->queue);
 313         return &req->req;
 314 }
 315
 316
 317 /*
 318  *      pxa25x_ep_free_request - deallocate a request data structure
 319  */
 320 static void
 321 pxa25x_ep_free_request (struct usb_ep *_ep, struct usb_request *_req)
 322 {
 323         struct pxa25x_request   *req;
 324
 325         req = container_of (_req, struct pxa25x_request, req);
 326         WARN_ON(!list_empty (&req->queue));
 327         kfree(req);
 328 }
 329
 330 /*-------------------------------------------------------------------------*/
 331
 332 /*
 333  *      done - retire a request; caller blocked irqs
 334  */
 335 static void done(struct pxa25x_ep *ep, struct pxa25x_request *req, int status)
 336 {
 337         unsigned                stopped = ep->stopped;
 338
 339         list_del_init(&req->queue);
 340
 341         if (likely (req->req.status == -EINPROGRESS))
 342                 req->req.status = status;
 343         else
 344                 status = req->req.status;
 345
 346         if (status && status != -ESHUTDOWN)
 347                 DBG(DBG_VERBOSE, "complete %s req %p stat %d len %u/%u\n",
 348                         ep->ep.name, &req->req, status,
 349                         req->req.actual, req->req.length);
 350
 351         /* don't modify queue heads during completion callback */
 352         ep->stopped = 1;
 353         req->req.complete(&ep->ep, &req->req);
 354         ep->stopped = stopped;
 355 }
 356
 357
 358 static inline void ep0_idle (struct pxa25x_udc *dev)
 359 {
 360         dev->ep0state = EP0_IDLE;
 361 }
 362
 363 static int
 364 write_packet(volatile u32 *uddr, struct pxa25x_request *req, unsigned max)
 365 {
 366         u8              *buf;
 367         unsigned        length, count;
 368
 369         buf = req->req.buf + req->req.actual;
 370         prefetch(buf);
 371
 372         /* how big will this packet be? */
 373         length = min(req->req.length - req->req.actual, max);
 374         req->req.actual += length;
 375
 376         count = length;
 377         while (likely(count--))
 378                 *uddr = *buf++;
 379
 380         return length;
 381 }
 382
 383 /*
 384  * write to an IN endpoint fifo, as many packets as possible.
 385  * irqs will use this to write the rest later.
 386  * caller guarantees at least one packet buffer is ready (or a zlp).
 387  */
 388 static int
 389 write_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req)
 390 {
 391         unsigned                max;
 392
 393         max = usb_endpoint_maxp(ep->ep.desc);
 394         do {
 395                 unsigned        count;
 396                 int             is_last, is_short;
 397
 398                 count = write_packet(ep->reg_uddr, req, max);
 399
 400                 /* last packet is usually short (or a zlp) */
 401                 if (unlikely (count != max))
 402                         is_last = is_short = 1;
 403                 else {
 404                         if (likely(req->req.length != req->req.actual)
 405                                         || req->req.zero)
 406                                 is_last = 0;
 407                         else
 408                                 is_last = 1;
 409                         /* interrupt/iso maxpacket may not fill the fifo */
 410                         is_short = unlikely (max < ep->fifo_size);
 411                 }
 412
 413                 DBG(DBG_VERY_NOISY, "wrote %s %d bytes%s%s %d left %p\n",
 414                         ep->ep.name, count,
 415                         is_last ? "/L" : "", is_short ? "/S" : "",
 416                         req->req.length - req->req.actual, req);
 417
 418                 /* let loose that packet. maybe try writing another one,
 419                  * double buffering might work.  TSP, TPC, and TFS
 420                  * bit values are the same for all normal IN endpoints.
 421                  */
 422                 *ep->reg_udccs = UDCCS_BI_TPC;
 423                 if (is_short)
 424                         *ep->reg_udccs = UDCCS_BI_TSP;
 425
 426                 /* requests complete when all IN data is in the FIFO */
 427                 if (is_last) {
 428                         done (ep, req, 0);
 429                         if (list_empty(&ep->queue))
 430                                 pio_irq_disable (ep->bEndpointAddress);
 431                         return 1;
 432                 }
 433
 434                 // TODO experiment: how robust can fifo mode tweaking be?
 435                 // double buffering is off in the default fifo mode, which
 436                 // prevents TFS from being set here.
 437
 438         } while (*ep->reg_udccs & UDCCS_BI_TFS);
 439         return 0;
 440 }
 441
 442 /* caller asserts req->pending (ep0 irq status nyet cleared); starts
 443  * ep0 data stage.  these chips want very simple state transitions.
 444  */
 445 static inline
 446 void ep0start(struct pxa25x_udc *dev, u32 flags, const char *tag)
 447 {
 448         UDCCS0 = flags|UDCCS0_SA|UDCCS0_OPR;
 449         USIR0 = USIR0_IR0;
 450         dev->req_pending = 0;
 451         DBG(DBG_VERY_NOISY, "%s %s, %02x/%02x\n",
 452                 __func__, tag, UDCCS0, flags);
 453 }
 454
 455 static int
 456 write_ep0_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req)
 457 {
 458         unsigned        count;
 459         int             is_short;
 460
 461         count = write_packet(&UDDR0, req, EP0_FIFO_SIZE);
 462         ep->dev->stats.write.bytes += count;
 463
 464         /* last packet "must be" short (or a zlp) */
 465         is_short = (count != EP0_FIFO_SIZE);
 466
 467         DBG(DBG_VERY_NOISY, "ep0in %d bytes %d left %p\n", count,
 468                 req->req.length - req->req.actual, req);
 469
 470         if (unlikely (is_short)) {
 471                 if (ep->dev->req_pending)
 472                         ep0start(ep->dev, UDCCS0_IPR, "short IN");
 473                 else
 474                         UDCCS0 = UDCCS0_IPR;
 475
 476                 count = req->req.length;
 477                 done (ep, req, 0);
 478                 ep0_idle(ep->dev);
 479 #ifndef CONFIG_ARCH_IXP4XX
 480 #if 1
 481                 /* This seems to get rid of lost status irqs in some cases:
 482                  * host responds quickly, or next request involves config
 483                  * change automagic, or should have been hidden, or ...
 484                  *
 485                  * FIXME get rid of all udelays possible...
 486                  */
 487                 if (count >= EP0_FIFO_SIZE) {
 488                         count = 100;
 489                         do {
 490                                 if ((UDCCS0 & UDCCS0_OPR) != 0) {
 491                                         /* clear OPR, generate ack */
 492                                         UDCCS0 = UDCCS0_OPR;
 493                                         break;
 494                                 }
 495                                 count--;
 496                                 udelay(1);
 497                         } while (count);
 498                 }
 499 #endif
 500 #endif
 501         } else if (ep->dev->req_pending)
 502                 ep0start(ep->dev, 0, "IN");
 503         return is_short;
 504 }
 505
 506
 507 /*
 508  * read_fifo -  unload packet(s) from the fifo we use for usb OUT
 509  * transfers and put them into the request.  caller should have made
 510  * sure there's at least one packet ready.
 511  *
 512  * returns true if the request completed because of short packet or the
 513  * request buffer having filled (and maybe overran till end-of-packet).
 514  */
 515 static int
 516 read_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req)
 517 {
 518         for (;;) {
 519                 u32             udccs;
 520                 u8              *buf;
 521                 unsigned        bufferspace, count, is_short;
 522
 523                 /* make sure there's a packet in the FIFO.
 524                  * UDCCS_{BO,IO}_RPC are all the same bit value.
 525                  * UDCCS_{BO,IO}_RNE are all the same bit value.
 526                  */
 527                 udccs = *ep->reg_udccs;
 528                 if (unlikely ((udccs & UDCCS_BO_RPC) == 0))
 529                         break;
 530                 buf = req->req.buf + req->req.actual;
 531                 prefetchw(buf);
 532                 bufferspace = req->req.length - req->req.actual;
 533
 534                 /* read all bytes from this packet */
 535                 if (likely (udccs & UDCCS_BO_RNE)) {
 536                         count = 1 + (0x0ff & *ep->reg_ubcr);
 537                         req->req.actual += min (count, bufferspace);
 538                 } else /* zlp */
 539                         count = 0;
 540                 is_short = (count < ep->ep.maxpacket);
 541                 DBG(DBG_VERY_NOISY, "read %s %02x, %d bytes%s req %p %d/%d\n",
 542                         ep->ep.name, udccs, count,
 543                         is_short ? "/S" : "",
 544                         req, req->req.actual, req->req.length);
 545                 while (likely (count-- != 0)) {
 546                         u8      byte = (u8) *ep->reg_uddr;
 547
 548                         if (unlikely (bufferspace == 0)) {
 549                                 /* this happens when the driver's buffer
 550                                  * is smaller than what the host sent.
 551                                  * discard the extra data.
 552                                  */
 553                                 if (req->req.status != -EOVERFLOW)
 554                                         DMSG("%s overflow %d\n",
 555                                                 ep->ep.name, count);
 556                                 req->req.status = -EOVERFLOW;
 557                         } else {
 558                                 *buf++ = byte;
 559                                 bufferspace--;
 560                         }
 561                 }
 562                 *ep->reg_udccs =  UDCCS_BO_RPC;
 563                 /* RPC/RSP/RNE could now reflect the other packet buffer */
 564
 565                 /* iso is one request per packet */
 566                 if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) {
 567                         if (udccs & UDCCS_IO_ROF)
 568                                 req->req.status = -EHOSTUNREACH;
 569                         /* more like "is_done" */
 570                         is_short = 1;
 571                 }
 572
 573                 /* completion */
 574                 if (is_short || req->req.actual == req->req.length) {
 575                         done (ep, req, 0);
 576                         if (list_empty(&ep->queue))
 577                                 pio_irq_disable (ep->bEndpointAddress);
 578                         return 1;
 579                 }
 580
 581                 /* finished that packet.  the next one may be waiting... */
 582         }
 583         return 0;
 584 }
 585
 586 /*
 587  * special ep0 version of the above.  no UBCR0 or double buffering; status
 588  * handshaking is magic.  most device protocols don't need control-OUT.
 589  * CDC vendor commands (and RNDIS), mass storage CB/CBI, and some other
 590  * protocols do use them.
 591  */
 592 static int
 593 read_ep0_fifo (struct pxa25x_ep *ep, struct pxa25x_request *req)
 594 {
 595         u8              *buf, byte;
 596         unsigned        bufferspace;
 597
 598         buf = req->req.buf + req->req.actual;
 599         bufferspace = req->req.length - req->req.actual;
 600
 601         while (UDCCS0 & UDCCS0_RNE) {
 602                 byte = (u8) UDDR0;
 603
 604                 if (unlikely (bufferspace == 0)) {
 605                         /* this happens when the driver's buffer
 606                          * is smaller than what the host sent.
 607                          * discard the extra data.
 608                          */
 609                         if (req->req.status != -EOVERFLOW)
 610                                 DMSG("%s overflow\n", ep->ep.name);
 611                         req->req.status = -EOVERFLOW;
 612                 } else {
 613                         *buf++ = byte;
 614                         req->req.actual++;
 615                         bufferspace--;
 616                 }
 617         }
 618
 619         UDCCS0 = UDCCS0_OPR | UDCCS0_IPR;
 620
 621         /* completion */
 622         if (req->req.actual >= req->req.length)
 623                 return 1;
 624
 625         /* finished that packet.  the next one may be waiting... */
 626         return 0;
 627 }
 628
 629 /*-------------------------------------------------------------------------*/
 630
 631 static int
 632 pxa25x_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
 633 {
 634         struct pxa25x_request   *req;
 635         struct pxa25x_ep        *ep;
 636         struct pxa25x_udc       *dev;
 637         unsigned long           flags;
 638
 639         req = container_of(_req, struct pxa25x_request, req);
 640         if (unlikely (!_req || !_req->complete || !_req->buf
 641                         || !list_empty(&req->queue))) {
 642                 DMSG("%s, bad params\n", __func__);
 643                 return -EINVAL;
 644         }
 645
 646         ep = container_of(_ep, struct pxa25x_ep, ep);
 647         if (unlikely(!_ep || (!ep->ep.desc && ep->ep.name != ep0name))) {
 648                 DMSG("%s, bad ep\n", __func__);
 649                 return -EINVAL;
 650         }
 651
 652         dev = ep->dev;
 653         if (unlikely (!dev->driver
 654                         || dev->gadget.speed == USB_SPEED_UNKNOWN)) {
 655                 DMSG("%s, bogus device state\n", __func__);
 656                 return -ESHUTDOWN;
 657         }
 658
 659         /* iso is always one packet per request, that's the only way
 660          * we can report per-packet status.  that also helps with dma.
 661          */
 662         if (unlikely (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC
 663                         && req->req.length > usb_endpoint_maxp(ep->ep.desc)))
 664                 return -EMSGSIZE;
 665
 666         DBG(DBG_NOISY, "%s queue req %p, len %d buf %p\n",
 667                 _ep->name, _req, _req->length, _req->buf);
 668
 669         local_irq_save(flags);
 670
 671         _req->status = -EINPROGRESS;
 672         _req->actual = 0;
 673
 674         /* kickstart this i/o queue? */
 675         if (list_empty(&ep->queue) && !ep->stopped) {
 676                 if (ep->ep.desc == NULL/* ep0 */) {
 677                         unsigned        length = _req->length;
 678
 679                         switch (dev->ep0state) {
 680                         case EP0_IN_DATA_PHASE:
 681                                 dev->stats.write.ops++;
 682                                 if (write_ep0_fifo(ep, req))
 683                                         req = NULL;
 684                                 break;
 685
 686                         case EP0_OUT_DATA_PHASE:
 687                                 dev->stats.read.ops++;
 688                                 /* messy ... */
 689                                 if (dev->req_config) {
 690                                         DBG(DBG_VERBOSE, "ep0 config ack%s\n",
 691                                                 dev->has_cfr ?  "" : " raced");
 692                                         if (dev->has_cfr)
 693                                                 UDCCFR = UDCCFR_AREN|UDCCFR_ACM
 694                                                         |UDCCFR_MB1;
 695                                         done(ep, req, 0);
 696                                         dev->ep0state = EP0_END_XFER;
 697                                         local_irq_restore (flags);
 698                                         return 0;
 699                                 }
 700                                 if (dev->req_pending)
 701                                         ep0start(dev, UDCCS0_IPR, "OUT");
 702                                 if (length == 0 || ((UDCCS0 & UDCCS0_RNE) != 0
 703                                                 && read_ep0_fifo(ep, req))) {
 704                                         ep0_idle(dev);
 705                                         done(ep, req, 0);
 706                                         req = NULL;
 707                                 }
 708                                 break;
 709
 710                         default:
 711                                 DMSG("ep0 i/o, odd state %d\n", dev->ep0state);
 712                                 local_irq_restore (flags);
 713                                 return -EL2HLT;
 714                         }
 715                 /* can the FIFO can satisfy the request immediately? */
 716                 } else if ((ep->bEndpointAddress & USB_DIR_IN) != 0) {
 717                         if ((*ep->reg_udccs & UDCCS_BI_TFS) != 0
 718                                         && write_fifo(ep, req))
 719                                 req = NULL;
 720                 } else if ((*ep->reg_udccs & UDCCS_BO_RFS) != 0
 721                                 && read_fifo(ep, req)) {
 722                         req = NULL;
 723                 }
 724
 725                 if (likely(req && ep->ep.desc))
 726                         pio_irq_enable(ep->bEndpointAddress);
 727         }
 728
 729         /* pio or dma irq handler advances the queue. */
 730         if (likely(req != NULL))
 731                 list_add_tail(&req->queue, &ep->queue);
 732         local_irq_restore(flags);
 733
 734         return 0;
 735 }
 736
 737
 738 /*
 739  *      nuke - dequeue ALL requests
 740  */
 741 static void nuke(struct pxa25x_ep *ep, int status)
 742 {
 743         struct pxa25x_request *req;
 744
 745         /* called with irqs blocked */
 746         while (!list_empty(&ep->queue)) {
 747                 req = list_entry(ep->queue.next,
 748                                 struct pxa25x_request,
 749                                 queue);
 750                 done(ep, req, status);
 751         }
 752         if (ep->ep.desc)
 753                 pio_irq_disable (ep->bEndpointAddress);
 754 }
 755
 756
 757 /* dequeue JUST ONE request */
 758 static int pxa25x_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)
 759 {
 760         struct pxa25x_ep        *ep;
 761         struct pxa25x_request   *req;
 762         unsigned long           flags;
 763
 764         ep = container_of(_ep, struct pxa25x_ep, ep);
 765         if (!_ep || ep->ep.name == ep0name)
 766                 return -EINVAL;
 767
 768         local_irq_save(flags);
 769
 770         /* make sure it's actually queued on this endpoint */
 771         list_for_each_entry (req, &ep->queue, queue) {
 772                 if (&req->req == _req)
 773                         break;
 774         }
 775         if (&req->req != _req) {
 776                 local_irq_restore(flags);
 777                 return -EINVAL;
 778         }
 779
 780         done(ep, req, -ECONNRESET);
 781
 782         local_irq_restore(flags);
 783         return 0;
 784 }
 785
 786 /*-------------------------------------------------------------------------*/
 787
 788 static int pxa25x_ep_set_halt(struct usb_ep *_ep, int value)
 789 {
 790         struct pxa25x_ep        *ep;
 791         unsigned long           flags;
 792
 793         ep = container_of(_ep, struct pxa25x_ep, ep);
 794         if (unlikely (!_ep
 795                         || (!ep->ep.desc && ep->ep.name != ep0name))
 796                         || ep->bmAttributes == USB_ENDPOINT_XFER_ISOC) {
 797                 DMSG("%s, bad ep\n", __func__);
 798                 return -EINVAL;
 799         }
 800         if (value == 0) {
 801                 /* this path (reset toggle+halt) is needed to implement
 802                  * SET_INTERFACE on normal hardware.  but it can't be
 803                  * done from software on the PXA UDC, and the hardware
 804                  * forgets to do it as part of SET_INTERFACE automagic.
 805                  */
 806                 DMSG("only host can clear %s halt\n", _ep->name);
 807                 return -EROFS;
 808         }
 809
 810         local_irq_save(flags);
 811
 812         if ((ep->bEndpointAddress & USB_DIR_IN) != 0
 813                         && ((*ep->reg_udccs & UDCCS_BI_TFS) == 0
 814                            || !list_empty(&ep->queue))) {
 815                 local_irq_restore(flags);
 816                 return -EAGAIN;
 817         }
 818
 819         /* FST bit is the same for control, bulk in, bulk out, interrupt in */
 820         *ep->reg_udccs = UDCCS_BI_FST|UDCCS_BI_FTF;
 821
 822         /* ep0 needs special care */
 823         if (!ep->ep.desc) {
 824                 start_watchdog(ep->dev);
 825                 ep->dev->req_pending = 0;
 826                 ep->dev->ep0state = EP0_STALL;
 827
 828         /* and bulk/intr endpoints like dropping stalls too */
 829         } else {
 830                 unsigned i;
 831                 for (i = 0; i < 1000; i += 20) {
 832                         if (*ep->reg_udccs & UDCCS_BI_SST)
 833                                 break;
 834                         udelay(20);
 835                 }
 836         }
 837         local_irq_restore(flags);
 838
 839         DBG(DBG_VERBOSE, "%s halt\n", _ep->name);
 840         return 0;
 841 }
 842
 843 static int pxa25x_ep_fifo_status(struct usb_ep *_ep)
 844 {
 845         struct pxa25x_ep        *ep;
 846
 847         ep = container_of(_ep, struct pxa25x_ep, ep);
 848         if (!_ep) {
 849                 DMSG("%s, bad ep\n", __func__);
 850                 return -ENODEV;
 851         }
 852         /* pxa can't report unclaimed bytes from IN fifos */
 853         if ((ep->bEndpointAddress & USB_DIR_IN) != 0)
 854                 return -EOPNOTSUPP;
 855         if (ep->dev->gadget.speed == USB_SPEED_UNKNOWN
 856                         || (*ep->reg_udccs & UDCCS_BO_RFS) == 0)
 857                 return 0;
 858         else
 859                 return (*ep->reg_ubcr & 0xfff) + 1;
 860 }
 861
 862 static void pxa25x_ep_fifo_flush(struct usb_ep *_ep)
 863 {
 864         struct pxa25x_ep        *ep;
 865
 866         ep = container_of(_ep, struct pxa25x_ep, ep);
 867         if (!_ep || ep->ep.name == ep0name || !list_empty(&ep->queue)) {
 868                 DMSG("%s, bad ep\n", __func__);
 869                 return;
 870         }
 871
 872         /* toggle and halt bits stay unchanged */
 873
 874         /* for OUT, just read and discard the FIFO contents. */
 875         if ((ep->bEndpointAddress & USB_DIR_IN) == 0) {
 876                 while (((*ep->reg_udccs) & UDCCS_BO_RNE) != 0)
 877                         (void) *ep->reg_uddr;
 878                 return;
 879         }
 880
 881         /* most IN status is the same, but ISO can't stall */
 882         *ep->reg_udccs = UDCCS_BI_TPC|UDCCS_BI_FTF|UDCCS_BI_TUR
 883                 | (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC
 884                         ? 0 : UDCCS_BI_SST);
 885 }
 886
 887
 888 static struct usb_ep_ops pxa25x_ep_ops = {
 889         .enable         = pxa25x_ep_enable,
 890         .disable        = pxa25x_ep_disable,
 891
 892         .alloc_request  = pxa25x_ep_alloc_request,
 893         .free_request   = pxa25x_ep_free_request,
 894
 895         .queue          = pxa25x_ep_queue,
 896         .dequeue        = pxa25x_ep_dequeue,
 897
 898         .set_halt       = pxa25x_ep_set_halt,
 899         .fifo_status    = pxa25x_ep_fifo_status,
 900         .fifo_flush     = pxa25x_ep_fifo_flush,
 901 };
 902
 903
 904 /* ---------------------------------------------------------------------------
 905  *      device-scoped parts of the api to the usb controller hardware
 906  * ---------------------------------------------------------------------------
 907  */
 908
 909 static int pxa25x_udc_get_frame(struct usb_gadget *_gadget)
 910 {
 911         return ((UFNRH & 0x07) << 8) | (UFNRL & 0xff);
 912 }
 913
 914 static int pxa25x_udc_wakeup(struct usb_gadget *_gadget)
 915 {
 916         /* host may not have enabled remote wakeup */
 917         if ((UDCCS0 & UDCCS0_DRWF) == 0)
 918                 return -EHOSTUNREACH;
 919         udc_set_mask_UDCCR(UDCCR_RSM);
 920         return 0;
 921 }
 922
 923 static void stop_activity(struct pxa25x_udc *, struct usb_gadget_driver *);
 924 static void udc_enable (struct pxa25x_udc *);
 925 static void udc_disable(struct pxa25x_udc *);
 926
 927 /* We disable the UDC -- and its 48 MHz clock -- whenever it's not
 928  * in active use.
 929  */
 930 static int pullup(struct pxa25x_udc *udc)
 931 {
 932         int is_active = udc->vbus && udc->pullup && !udc->suspended;
 933         DMSG("%s\n", is_active ? "active" : "inactive");
 934         if (is_active) {
 935                 if (!udc->active) {
 936                         udc->active = 1;
 937                         /* Enable clock for USB device */
 938                         clk_enable(udc->clk);
 939                         udc_enable(udc);
 940                 }
 941         } else {
 942                 if (udc->active) {
 943                         if (udc->gadget.speed != USB_SPEED_UNKNOWN) {
 944                                 DMSG("disconnect %s\n", udc->driver
 945                                         ? udc->driver->driver.name
 946                                         : "(no driver)");
 947                                 stop_activity(udc, udc->driver);
 948                         }
 949                         udc_disable(udc);
 950                         /* Disable clock for USB device */
 951                         clk_disable(udc->clk);
 952                         udc->active = 0;
 953                 }
 954
 955         }
 956         return 0;
 957 }
 958
 959 /* VBUS reporting logically comes from a transceiver */
 960 static int pxa25x_udc_vbus_session(struct usb_gadget *_gadget, int is_active)
 961 {
 962         struct pxa25x_udc       *udc;
 963
 964         udc = container_of(_gadget, struct pxa25x_udc, gadget);
 965         udc->vbus = is_active;
 966         DMSG("vbus %s\n", is_active ? "supplied" : "inactive");
 967         pullup(udc);
 968         return 0;
 969 }
 970
 971 /* drivers may have software control over D+ pullup */
 972 static int pxa25x_udc_pullup(struct usb_gadget *_gadget, int is_active)
 973 {
 974         struct pxa25x_udc       *udc;
 975
 976         udc = container_of(_gadget, struct pxa25x_udc, gadget);
 977
 978         /* not all boards support pullup control */
 979         if (!gpio_is_valid(udc->mach->gpio_pullup) && !udc->mach->udc_command)
 980                 return -EOPNOTSUPP;
 981
 982         udc->pullup = (is_active != 0);
 983         pullup(udc);
 984         return 0;
 985 }
 986
 987 /* boards may consume current from VBUS, up to 100-500mA based on config.
 988  * the 500uA suspend ceiling means that exclusively vbus-powered PXA designs
 989  * violate USB specs.
 990  */
 991 static int pxa25x_udc_vbus_draw(struct usb_gadget *_gadget, unsigned mA)
 992 {
 993         struct pxa25x_udc       *udc;
 994
 995         udc = container_of(_gadget, struct pxa25x_udc, gadget);
 996
 997         if (!IS_ERR_OR_NULL(udc->transceiver))
 998                 return usb_phy_set_power(udc->transceiver, mA);
 999         return -EOPNOTSUPP;
1000 }
1001
1002 static int pxa25x_start(struct usb_gadget_driver *driver,
1003                 int (*bind)(struct usb_gadget *));
1004 static int pxa25x_stop(struct usb_gadget_driver *driver);
1005
1006 static const struct usb_gadget_ops pxa25x_udc_ops = {
1007         .get_frame      = pxa25x_udc_get_frame,
1008         .wakeup         = pxa25x_udc_wakeup,
1009         .vbus_session   = pxa25x_udc_vbus_session,
1010         .pullup         = pxa25x_udc_pullup,
1011         .vbus_draw      = pxa25x_udc_vbus_draw,
1012         .start          = pxa25x_start,
1013         .stop           = pxa25x_stop,
1014 };
1015
1016 /*-------------------------------------------------------------------------*/
1017
1018 #ifdef CONFIG_USB_GADGET_DEBUG_FS
1019
1020 static int
1021 udc_seq_show(struct seq_file *m, void *_d)
1022 {
1023         struct pxa25x_udc       *dev = m->private;
1024         unsigned long           flags;
1025         int                     i;
1026         u32                     tmp;
1027
1028         local_irq_save(flags);
1029
1030         /* basic device status */
1031         seq_printf(m, DRIVER_DESC "\n"
1032                 "%s version: %s\nGadget driver: %s\nHost %s\n\n",
1033                 driver_name, DRIVER_VERSION SIZE_STR "(pio)",
1034                 dev->driver ? dev->driver->driver.name : "(none)",
1035                 dev->gadget.speed == USB_SPEED_FULL ? "full speed" : "disconnected");
1036
1037         /* registers for device and ep0 */
1038         seq_printf(m,
1039                 "uicr %02X.%02X, usir %02X.%02x, ufnr %02X.%02X\n",
1040                 UICR1, UICR0, USIR1, USIR0, UFNRH, UFNRL);
1041
1042         tmp = UDCCR;
1043         seq_printf(m,
1044                 "udccr %02X =%s%s%s%s%s%s%s%s\n", tmp,
1045                 (tmp & UDCCR_REM) ? " rem" : "",
1046                 (tmp & UDCCR_RSTIR) ? " rstir" : "",
1047                 (tmp & UDCCR_SRM) ? " srm" : "",
1048                 (tmp & UDCCR_SUSIR) ? " susir" : "",
1049                 (tmp & UDCCR_RESIR) ? " resir" : "",
1050                 (tmp & UDCCR_RSM) ? " rsm" : "",
1051                 (tmp & UDCCR_UDA) ? " uda" : "",
1052                 (tmp & UDCCR_UDE) ? " ude" : "");
1053
1054         tmp = UDCCS0;
1055         seq_printf(m,
1056                 "udccs0 %02X =%s%s%s%s%s%s%s%s\n", tmp,
1057                 (tmp & UDCCS0_SA) ? " sa" : "",
1058                 (tmp & UDCCS0_RNE) ? " rne" : "",
1059                 (tmp & UDCCS0_FST) ? " fst" : "",
1060                 (tmp & UDCCS0_SST) ? " sst" : "",
1061                 (tmp & UDCCS0_DRWF) ? " dwrf" : "",
1062                 (tmp & UDCCS0_FTF) ? " ftf" : "",
1063                 (tmp & UDCCS0_IPR) ? " ipr" : "",
1064                 (tmp & UDCCS0_OPR) ? " opr" : "");
1065
1066         if (dev->has_cfr) {
1067                 tmp = UDCCFR;
1068                 seq_printf(m,
1069                         "udccfr %02X =%s%s\n", tmp,
1070                         (tmp & UDCCFR_AREN) ? " aren" : "",
1071                         (tmp & UDCCFR_ACM) ? " acm" : "");
1072         }
1073
1074         if (dev->gadget.speed != USB_SPEED_FULL || !dev->driver)
1075                 goto done;
1076
1077         seq_printf(m, "ep0 IN %lu/%lu, OUT %lu/%lu\nirqs %lu\n\n",
1078                 dev->stats.write.bytes, dev->stats.write.ops,
1079                 dev->stats.read.bytes, dev->stats.read.ops,
1080                 dev->stats.irqs);
1081
1082         /* dump endpoint queues */
1083         for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) {
1084                 struct pxa25x_ep        *ep = &dev->ep [i];
1085                 struct pxa25x_request   *req;
1086
1087                 if (i != 0) {
1088                         const struct usb_endpoint_descriptor    *desc;
1089
1090                         desc = ep->ep.desc;
1091                         if (!desc)
1092                                 continue;
1093                         tmp = *dev->ep [i].reg_udccs;
1094                         seq_printf(m,
1095                                 "%s max %d %s udccs %02x irqs %lu\n",
1096                                 ep->ep.name, usb_endpoint_maxp(desc),
1097                                 "pio", tmp, ep->pio_irqs);
1098                         /* TODO translate all five groups of udccs bits! */
1099
1100                 } else /* ep0 should only have one transfer queued */
1101                         seq_printf(m, "ep0 max 16 pio irqs %lu\n",
1102                                 ep->pio_irqs);
1103
1104                 if (list_empty(&ep->queue)) {
1105                         seq_printf(m, "\t(nothing queued)\n");
1106                         continue;
1107                 }
1108                 list_for_each_entry(req, &ep->queue, queue) {
1109                         seq_printf(m,
1110                                         "\treq %p len %d/%d buf %p\n",
1111                                         &req->req, req->req.actual,
1112                                         req->req.length, req->req.buf);
1113                 }
1114         }
1115
1116 done:
1117         local_irq_restore(flags);
1118         return 0;
1119 }
1120
1121 static int
1122 udc_debugfs_open(struct inode *inode, struct file *file)
1123 {
1124         return single_open(file, udc_seq_show, inode->i_private);
1125 }
1126
1127 static const struct file_operations debug_fops = {
1128         .open           = udc_debugfs_open,
1129         .read           = seq_read,
1130         .llseek         = seq_lseek,
1131         .release        = single_release,
1132         .owner          = THIS_MODULE,
1133 };
1134
1135 #define create_debug_files(dev) \
1136         do { \
1137                 dev->debugfs_udc = debugfs_create_file(dev->gadget.name, \
1138                         S_IRUGO, NULL, dev, &debug_fops); \
1139         } while (0)
1140 #define remove_debug_files(dev) \
1141         do { \
1142                 if (dev->debugfs_udc) \
1143                         debugfs_remove(dev->debugfs_udc); \
1144         } while (0)
1145
1146 #else   /* !CONFIG_USB_GADGET_DEBUG_FILES */
1147
1148 #define create_debug_files(dev) do {} while (0)
1149 #define remove_debug_files(dev) do {} while (0)
1150
1151 #endif  /* CONFIG_USB_GADGET_DEBUG_FILES */
1152
1153 /*-------------------------------------------------------------------------*/
1154
1155 /*
1156  *      udc_disable - disable USB device controller
1157  */
1158 static void udc_disable(struct pxa25x_udc *dev)
1159 {
1160         /* block all irqs */
1161         udc_set_mask_UDCCR(UDCCR_SRM|UDCCR_REM);
1162         UICR0 = UICR1 = 0xff;
1163         UFNRH = UFNRH_SIM;
1164
1165         /* if hardware supports it, disconnect from usb */
1166         pullup_off();
1167
1168         udc_clear_mask_UDCCR(UDCCR_UDE);
1169
1170         ep0_idle (dev);
1171         dev->gadget.speed = USB_SPEED_UNKNOWN;
1172 }
1173
1174
1175 /*
1176  *      udc_reinit - initialize software state
1177  */
1178 static void udc_reinit(struct pxa25x_udc *dev)
1179 {
1180         u32     i;
1181
1182         /* device/ep0 records init */
1183         INIT_LIST_HEAD (&dev->gadget.ep_list);
1184         INIT_LIST_HEAD (&dev->gadget.ep0->ep_list);
1185         dev->ep0state = EP0_IDLE;
1186
1187         /* basic endpoint records init */
1188         for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) {
1189                 struct pxa25x_ep *ep = &dev->ep[i];
1190
1191                 if (i != 0)
1192                         list_add_tail (&ep->ep.ep_list, &dev->gadget.ep_list);
1193
1194                 ep->ep.desc = NULL;
1195                 ep->stopped = 0;
1196                 INIT_LIST_HEAD (&ep->queue);
1197                 ep->pio_irqs = 0;
1198         }
1199
1200         /* the rest was statically initialized, and is read-only */
1201 }
1202
1203 /* until it's enabled, this UDC should be completely invisible
1204  * to any USB host.
1205  */
1206 static void udc_enable (struct pxa25x_udc *dev)
1207 {
1208         udc_clear_mask_UDCCR(UDCCR_UDE);
1209
1210         /* try to clear these bits before we enable the udc */
1211         udc_ack_int_UDCCR(UDCCR_SUSIR|/*UDCCR_RSTIR|*/UDCCR_RESIR);
1212
1213         ep0_idle(dev);
1214         dev->gadget.speed = USB_SPEED_UNKNOWN;
1215         dev->stats.irqs = 0;
1216
1217         /*
1218          * sequence taken from chapter 12.5.10, PXA250 AppProcDevManual:
1219          * - enable UDC
1220          * - if RESET is already in progress, ack interrupt
1221          * - unmask reset interrupt
1222          */
1223         udc_set_mask_UDCCR(UDCCR_UDE);
1224         if (!(UDCCR & UDCCR_UDA))
1225                 udc_ack_int_UDCCR(UDCCR_RSTIR);
1226
1227         if (dev->has_cfr /* UDC_RES2 is defined */) {
1228                 /* pxa255 (a0+) can avoid a set_config race that could
1229                  * prevent gadget drivers from configuring correctly
1230                  */
1231                 UDCCFR = UDCCFR_ACM | UDCCFR_MB1;
1232         } else {
1233                 /* "USB test mode" for pxa250 errata 40-42 (stepping a0, a1)
1234                  * which could result in missing packets and interrupts.
1235                  * supposedly one bit per endpoint, controlling whether it
1236                  * double buffers or not; ACM/AREN bits fit into the holes.
1237                  * zero bits (like USIR0_IRx) disable double buffering.
1238                  */
1239                 UDC_RES1 = 0x00;
1240                 UDC_RES2 = 0x00;
1241         }
1242
1243         /* enable suspend/resume and reset irqs */
1244         udc_clear_mask_UDCCR(UDCCR_SRM | UDCCR_REM);
1245
1246         /* enable ep0 irqs */
1247         UICR0 &= ~UICR0_IM0;
1248
1249         /* if hardware supports it, pullup D+ and wait for reset */
1250         pullup_on();
1251 }
1252
1253
1254 /* when a driver is successfully registered, it will receive
1255  * control requests including set_configuration(), which enables
1256  * non-control requests.  then usb traffic follows until a
1257  * disconnect is reported.  then a host may connect again, or
1258  * the driver might get unbound.
1259  */
1260 static int pxa25x_start(struct usb_gadget_driver *driver,
1261                 int (*bind)(struct usb_gadget *))
1262 {
1263         struct pxa25x_udc       *dev = the_controller;
1264         int                     retval;
1265
1266         if (!driver
1267                         || driver->max_speed < USB_SPEED_FULL
1268                         || !bind
1269                         || !driver->disconnect
1270                         || !driver->setup)
1271                 return -EINVAL;
1272         if (!dev)
1273                 return -ENODEV;
1274         if (dev->driver)
1275                 return -EBUSY;
1276
1277         /* first hook up the driver ... */
1278         dev->driver = driver;
1279         dev->gadget.dev.driver = &driver->driver;
1280         dev->pullup = 1;
1281
1282         retval = device_add (&dev->gadget.dev);
1283         if (retval) {
1284 fail:
1285                 dev->driver = NULL;
1286                 dev->gadget.dev.driver = NULL;
1287                 return retval;
1288         }
1289         retval = bind(&dev->gadget);
1290         if (retval) {
1291                 DMSG("bind to driver %s --> error %d\n",
1292                                 driver->driver.name, retval);
1293                 device_del (&dev->gadget.dev);
1294                 goto fail;
1295         }
1296
1297         /* ... then enable host detection and ep0; and we're ready
1298          * for set_configuration as well as eventual disconnect.
1299          */
1300         DMSG("registered gadget driver '%s'\n", driver->driver.name);
1301
1302         /* connect to bus through transceiver */
1303         if (!IS_ERR_OR_NULL(dev->transceiver)) {
1304                 retval = otg_set_peripheral(dev->transceiver->otg,
1305                                                 &dev->gadget);
1306                 if (retval) {
1307                         DMSG("can't bind to transceiver\n");
1308                         if (driver->unbind)
1309                                 driver->unbind(&dev->gadget);
1310                         goto bind_fail;
1311                 }
1312         }
1313
1314         pullup(dev);
1315         dump_state(dev);
1316         return 0;
1317 bind_fail:
1318         return retval;
1319 }
1320
1321 static void
1322 stop_activity(struct pxa25x_udc *dev, struct usb_gadget_driver *driver)
1323 {
1324         int i;
1325
1326         /* don't disconnect drivers more than once */
1327         if (dev->gadget.speed == USB_SPEED_UNKNOWN)
1328                 driver = NULL;
1329         dev->gadget.speed = USB_SPEED_UNKNOWN;
1330
1331         /* prevent new request submissions, kill any outstanding requests  */
1332         for (i = 0; i < PXA_UDC_NUM_ENDPOINTS; i++) {
1333                 struct pxa25x_ep *ep = &dev->ep[i];
1334
1335                 ep->stopped = 1;
1336                 nuke(ep, -ESHUTDOWN);
1337         }
1338         del_timer_sync(&dev->timer);
1339
1340         /* report disconnect; the driver is already quiesced */
1341         if (driver)
1342                 driver->disconnect(&dev->gadget);
1343
1344         /* re-init driver-visible data structures */
1345         udc_reinit(dev);
1346 }
1347
1348 static int pxa25x_stop(struct usb_gadget_driver *driver)
1349 {
1350         struct pxa25x_udc       *dev = the_controller;
1351
1352         if (!dev)
1353                 return -ENODEV;
1354         if (!driver || driver != dev->driver || !driver->unbind)
1355                 return -EINVAL;
1356
1357         local_irq_disable();
1358         dev->pullup = 0;
1359         pullup(dev);
1360         stop_activity(dev, driver);
1361         local_irq_enable();
1362
1363         if (!IS_ERR_OR_NULL(dev->transceiver))
1364                 (void) otg_set_peripheral(dev->transceiver->otg, NULL);
1365
1366         driver->unbind(&dev->gadget);
1367         dev->gadget.dev.driver = NULL;
1368         dev->driver = NULL;
1369
1370         device_del (&dev->gadget.dev);
1371
1372         DMSG("unregistered gadget driver '%s'\n", driver->driver.name);
1373         dump_state(dev);
1374         return 0;
1375 }
1376
1377 /*-------------------------------------------------------------------------*/
1378
1379 #ifdef CONFIG_ARCH_LUBBOCK
1380
1381 /* Lubbock has separate connect and disconnect irqs.  More typical designs
1382  * use one GPIO as the VBUS IRQ, and another to control the D+ pullup.
1383  */
1384
1385 static irqreturn_t
1386 lubbock_vbus_irq(int irq, void *_dev)
1387 {
1388         struct pxa25x_udc       *dev = _dev;
1389         int                     vbus;
1390
1391         dev->stats.irqs++;
1392         switch (irq) {
1393         case LUBBOCK_USB_IRQ:
1394                 vbus = 1;
1395                 disable_irq(LUBBOCK_USB_IRQ);
1396                 enable_irq(LUBBOCK_USB_DISC_IRQ);
1397                 break;
1398         case LUBBOCK_USB_DISC_IRQ:
1399                 vbus = 0;
1400                 disable_irq(LUBBOCK_USB_DISC_IRQ);
1401                 enable_irq(LUBBOCK_USB_IRQ);
1402                 break;
1403         default:
1404                 return IRQ_NONE;
1405         }
1406
1407         pxa25x_udc_vbus_session(&dev->gadget, vbus);
1408         return IRQ_HANDLED;
1409 }
1410
1411 #endif
1412
1413
1414 /*-------------------------------------------------------------------------*/
1415
1416 static inline void clear_ep_state (struct pxa25x_udc *dev)
1417 {
1418         unsigned i;
1419
1420         /* hardware SET_{CONFIGURATION,INTERFACE} automagic resets endpoint
1421          * fifos, and pending transactions mustn't be continued in any case.
1422          */
1423         for (i = 1; i < PXA_UDC_NUM_ENDPOINTS; i++)
1424                 nuke(&dev->ep[i], -ECONNABORTED);
1425 }
1426
1427 static void udc_watchdog(unsigned long _dev)
1428 {
1429         struct pxa25x_udc       *dev = (void *)_dev;
1430
1431         local_irq_disable();
1432         if (dev->ep0state == EP0_STALL
1433                         && (UDCCS0 & UDCCS0_FST) == 0
1434                         && (UDCCS0 & UDCCS0_SST) == 0) {
1435                 UDCCS0 = UDCCS0_FST|UDCCS0_FTF;
1436                 DBG(DBG_VERBOSE, "ep0 re-stall\n");
1437                 start_watchdog(dev);
1438         }
1439         local_irq_enable();
1440 }
1441
1442 static void handle_ep0 (struct pxa25x_udc *dev)
1443 {
1444         u32                     udccs0 = UDCCS0;
1445         struct pxa25x_ep        *ep = &dev->ep [0];
1446         struct pxa25x_request   *req;
1447         union {
1448                 struct usb_ctrlrequest  r;
1449                 u8                      raw [8];
1450                 u32                     word [2];
1451         } u;
1452
1453         if (list_empty(&ep->queue))
1454                 req = NULL;
1455         else
1456                 req = list_entry(ep->queue.next, struct pxa25x_request, queue);
1457
1458         /* clear stall status */
1459         if (udccs0 & UDCCS0_SST) {
1460                 nuke(ep, -EPIPE);
1461                 UDCCS0 = UDCCS0_SST;
1462                 del_timer(&dev->timer);
1463                 ep0_idle(dev);
1464         }
1465
1466         /* previous request unfinished?  non-error iff back-to-back ... */
1467         if ((udccs0 & UDCCS0_SA) != 0 && dev->ep0state != EP0_IDLE) {
1468                 nuke(ep, 0);
1469                 del_timer(&dev->timer);
1470                 ep0_idle(dev);
1471         }
1472
1473         switch (dev->ep0state) {
1474         case EP0_IDLE:
1475                 /* late-breaking status? */
1476                 udccs0 = UDCCS0;
1477
1478                 /* start control request? */
1479                 if (likely((udccs0 & (UDCCS0_OPR|UDCCS0_SA|UDCCS0_RNE))
1480                                 == (UDCCS0_OPR|UDCCS0_SA|UDCCS0_RNE))) {
1481                         int i;
1482
1483                         nuke (ep, -EPROTO);
1484
1485                         /* read SETUP packet */
1486                         for (i = 0; i < 8; i++) {
1487                                 if (unlikely(!(UDCCS0 & UDCCS0_RNE))) {
1488 bad_setup:
1489                                         DMSG("SETUP %d!\n", i);
1490                                         goto stall;
1491                                 }
1492                                 u.raw [i] = (u8) UDDR0;
1493                         }
1494                         if (unlikely((UDCCS0 & UDCCS0_RNE) != 0))
1495                                 goto bad_setup;
1496
1497 got_setup:
1498                         DBG(DBG_VERBOSE, "SETUP %02x.%02x v%04x i%04x l%04x\n",
1499                                 u.r.bRequestType, u.r.bRequest,
1500                                 le16_to_cpu(u.r.wValue),
1501                                 le16_to_cpu(u.r.wIndex),
1502                                 le16_to_cpu(u.r.wLength));
1503
1504                         /* cope with automagic for some standard requests. */
1505                         dev->req_std = (u.r.bRequestType & USB_TYPE_MASK)
1506                                                 == USB_TYPE_STANDARD;
1507                         dev->req_config = 0;
1508                         dev->req_pending = 1;
1509                         switch (u.r.bRequest) {
1510                         /* hardware restricts gadget drivers here! */
1511                         case USB_REQ_SET_CONFIGURATION:
1512                                 if (u.r.bRequestType == USB_RECIP_DEVICE) {
1513                                         /* reflect hardware's automagic
1514                                          * up to the gadget driver.
1515                                          */
1516 config_change:
1517                                         dev->req_config = 1;
1518                                         clear_ep_state(dev);
1519                                         /* if !has_cfr, there's no synch
1520                                          * else use AREN (later) not SA|OPR
1521                                          * USIR0_IR0 acts edge sensitive
1522                                          */
1523                                 }
1524                                 break;
1525                         /* ... and here, even more ... */
1526                         case USB_REQ_SET_INTERFACE:
1527                                 if (u.r.bRequestType == USB_RECIP_INTERFACE) {
1528                                         /* udc hardware is broken by design:
1529                                          *  - altsetting may only be zero;
1530                                          *  - hw resets all interfaces' eps;
1531                                          *  - ep reset doesn't include halt(?).
1532                                          */
1533                                         DMSG("broken set_interface (%d/%d)\n",
1534                                                 le16_to_cpu(u.r.wIndex),
1535                                                 le16_to_cpu(u.r.wValue));
1536                                         goto config_change;
1537                                 }
1538                                 break;
1539                         /* hardware was supposed to hide this */
1540                         case USB_REQ_SET_ADDRESS:
1541                                 if (u.r.bRequestType == USB_RECIP_DEVICE) {
1542                                         ep0start(dev, 0, "address");
1543                                         return;
1544                                 }
1545                                 break;
1546                         }
1547
1548                         if (u.r.bRequestType & USB_DIR_IN)
1549                                 dev->ep0state = EP0_IN_DATA_PHASE;
1550                         else
1551                                 dev->ep0state = EP0_OUT_DATA_PHASE;
1552
1553                         i = dev->driver->setup(&dev->gadget, &u.r);
1554                         if (i < 0) {
1555                                 /* hardware automagic preventing STALL... */
1556                                 if (dev->req_config) {
1557                                         /* hardware sometimes neglects to tell
1558                                          * tell us about config change events,
1559                                          * so later ones may fail...
1560                                          */
1561                                         WARNING("config change %02x fail %d?\n",
1562                                                 u.r.bRequest, i);
1563                                         return;
1564                                         /* TODO experiment:  if has_cfr,
1565                                          * hardware didn't ACK; maybe we
1566                                          * could actually STALL!
1567                                          */
1568                                 }
1569                                 DBG(DBG_VERBOSE, "protocol STALL, "
1570                                         "%02x err %d\n", UDCCS0, i);
1571 stall:
1572                                 /* the watchdog timer helps deal with cases
1573                                  * where udc seems to clear FST wrongly, and
1574                                  * then NAKs instead of STALLing.
1575                                  */
1576                                 ep0start(dev, UDCCS0_FST|UDCCS0_FTF, "stall");
1577                                 start_watchdog(dev);
1578                                 dev->ep0state = EP0_STALL;
1579
1580                         /* deferred i/o == no response yet */
1581                         } else if (dev->req_pending) {
1582                                 if (likely(dev->ep0state == EP0_IN_DATA_PHASE
1583                                                 || dev->req_std || u.r.wLength))
1584                                         ep0start(dev, 0, "defer");
1585                                 else
1586                                         ep0start(dev, UDCCS0_IPR, "defer/IPR");
1587                         }
1588
1589                         /* expect at least one data or status stage irq */
1590                         return;
1591
1592                 } else if (likely((udccs0 & (UDCCS0_OPR|UDCCS0_SA))
1593                                 == (UDCCS0_OPR|UDCCS0_SA))) {
1594                         unsigned i;
1595
1596                         /* pxa210/250 erratum 131 for B0/B1 says RNE lies.
1597                          * still observed on a pxa255 a0.
1598                          */
1599                         DBG(DBG_VERBOSE, "e131\n");
1600                         nuke(ep, -EPROTO);
1601
1602                         /* read SETUP data, but don't trust it too much */
1603                         for (i = 0; i < 8; i++)
1604                                 u.raw [i] = (u8) UDDR0;
1605                         if ((u.r.bRequestType & USB_RECIP_MASK)
1606                                         > USB_RECIP_OTHER)
1607                                 goto stall;
1608                         if (u.word [0] == 0 && u.word [1] == 0)
1609                                 goto stall;
1610                         goto got_setup;
1611                 } else {
1612                         /* some random early IRQ:
1613                          * - we acked FST
1614                          * - IPR cleared
1615                          * - OPR got set, without SA (likely status stage)
1616                          */
1617                         UDCCS0 = udccs0 & (UDCCS0_SA|UDCCS0_OPR);
1618                 }
1619                 break;
1620         case EP0_IN_DATA_PHASE:                 /* GET_DESCRIPTOR etc */
1621                 if (udccs0 & UDCCS0_OPR) {
1622                         UDCCS0 = UDCCS0_OPR|UDCCS0_FTF;
1623                         DBG(DBG_VERBOSE, "ep0in premature status\n");
1624                         if (req)
1625                                 done(ep, req, 0);
1626                         ep0_idle(dev);
1627                 } else /* irq was IPR clearing */ {
1628                         if (req) {
1629                                 /* this IN packet might finish the request */
1630                                 (void) write_ep0_fifo(ep, req);
1631                         } /* else IN token before response was written */
1632                 }
1633                 break;
1634         case EP0_OUT_DATA_PHASE:                /* SET_DESCRIPTOR etc */
1635                 if (udccs0 & UDCCS0_OPR) {
1636                         if (req) {
1637                                 /* this OUT packet might finish the request */
1638                                 if (read_ep0_fifo(ep, req))
1639                                         done(ep, req, 0);
1640                                 /* else more OUT packets expected */
1641                         } /* else OUT token before read was issued */
1642                 } else /* irq was IPR clearing */ {
1643                         DBG(DBG_VERBOSE, "ep0out premature status\n");
1644                         if (req)
1645                                 done(ep, req, 0);
1646                         ep0_idle(dev);
1647                 }
1648                 break;
1649         case EP0_END_XFER:
1650                 if (req)
1651                         done(ep, req, 0);
1652                 /* ack control-IN status (maybe in-zlp was skipped)
1653                  * also appears after some config change events.
1654                  */
1655                 if (udccs0 & UDCCS0_OPR)
1656                         UDCCS0 = UDCCS0_OPR;
1657                 ep0_idle(dev);
1658                 break;
1659         case EP0_STALL:
1660                 UDCCS0 = UDCCS0_FST;
1661                 break;
1662         }
1663         USIR0 = USIR0_IR0;
1664 }
1665
1666 static void handle_ep(struct pxa25x_ep *ep)
1667 {
1668         struct pxa25x_request   *req;
1669         int                     is_in = ep->bEndpointAddress & USB_DIR_IN;
1670         int                     completed;
1671         u32                     udccs, tmp;
1672
1673         do {
1674                 completed = 0;
1675                 if (likely (!list_empty(&ep->queue)))
1676                         req = list_entry(ep->queue.next,
1677                                         struct pxa25x_request, queue);
1678                 else
1679                         req = NULL;
1680
1681                 // TODO check FST handling
1682
1683                 udccs = *ep->reg_udccs;
1684                 if (unlikely(is_in)) {  /* irq from TPC, SST, or (ISO) TUR */
1685                         tmp = UDCCS_BI_TUR;
1686                         if (likely(ep->bmAttributes == USB_ENDPOINT_XFER_BULK))
1687                                 tmp |= UDCCS_BI_SST;
1688                         tmp &= udccs;
1689                         if (likely (tmp))
1690                                 *ep->reg_udccs = tmp;
1691                         if (req && likely ((udccs & UDCCS_BI_TFS) != 0))
1692                                 completed = write_fifo(ep, req);
1693
1694                 } else {        /* irq from RPC (or for ISO, ROF) */
1695                         if (likely(ep->bmAttributes == USB_ENDPOINT_XFER_BULK))
1696                                 tmp = UDCCS_BO_SST | UDCCS_BO_DME;
1697                         else
1698                                 tmp = UDCCS_IO_ROF | UDCCS_IO_DME;
1699                         tmp &= udccs;
1700                         if (likely(tmp))
1701                                 *ep->reg_udccs = tmp;
1702
1703                         /* fifos can hold packets, ready for reading... */
1704                         if (likely(req)) {
1705                                 completed = read_fifo(ep, req);
1706                         } else
1707                                 pio_irq_disable (ep->bEndpointAddress);
1708                 }
1709                 ep->pio_irqs++;
1710         } while (completed);
1711 }
1712
1713 /*
1714  *      pxa25x_udc_irq - interrupt handler
1715  *
1716  * avoid delays in ep0 processing. the control handshaking isn't always
1717  * under software control (pxa250c0 and the pxa255 are better), and delays
1718  * could cause usb protocol errors.
1719  */
1720 static irqreturn_t
1721 pxa25x_udc_irq(int irq, void *_dev)
1722 {
1723         struct pxa25x_udc       *dev = _dev;
1724         int                     handled;
1725
1726         dev->stats.irqs++;
1727         do {
1728                 u32             udccr = UDCCR;
1729
1730                 handled = 0;
1731
1732                 /* SUSpend Interrupt Request */
1733                 if (unlikely(udccr & UDCCR_SUSIR)) {
1734                         udc_ack_int_UDCCR(UDCCR_SUSIR);
1735                         handled = 1;
1736                         DBG(DBG_VERBOSE, "USB suspend\n");
1737
1738                         if (dev->gadget.speed != USB_SPEED_UNKNOWN
1739                                         && dev->driver
1740                                         && dev->driver->suspend)
1741                                 dev->driver->suspend(&dev->gadget);
1742                         ep0_idle (dev);
1743                 }
1744
1745                 /* RESume Interrupt Request */
1746                 if (unlikely(udccr & UDCCR_RESIR)) {
1747                         udc_ack_int_UDCCR(UDCCR_RESIR);
1748                         handled = 1;
1749                         DBG(DBG_VERBOSE, "USB resume\n");
1750
1751                         if (dev->gadget.speed != USB_SPEED_UNKNOWN
1752                                         && dev->driver
1753                                         && dev->driver->resume)
1754                                 dev->driver->resume(&dev->gadget);
1755                 }
1756
1757                 /* ReSeT Interrupt Request - USB reset */
1758                 if (unlikely(udccr & UDCCR_RSTIR)) {
1759                         udc_ack_int_UDCCR(UDCCR_RSTIR);
1760                         handled = 1;
1761
1762                         if ((UDCCR & UDCCR_UDA) == 0) {
1763                                 DBG(DBG_VERBOSE, "USB reset start\n");
1764
1765                                 /* reset driver and endpoints,
1766                                  * in case that's not yet done
1767                                  */
1768                                 stop_activity (dev, dev->driver);
1769
1770                         } else {
1771                                 DBG(DBG_VERBOSE, "USB reset end\n");
1772                                 dev->gadget.speed = USB_SPEED_FULL;
1773                                 memset(&dev->stats, 0, sizeof dev->stats);
1774                                 /* driver and endpoints are still reset */
1775                         }
1776
1777                 } else {
1778                         u32     usir0 = USIR0 & ~UICR0;
1779                         u32     usir1 = USIR1 & ~UICR1;
1780                         int     i;
1781
1782                         if (unlikely (!usir0 && !usir1))
1783                                 continue;
1784
1785                         DBG(DBG_VERY_NOISY, "irq %02x.%02x\n", usir1, usir0);
1786
1787                         /* control traffic */
1788                         if (usir0 & USIR0_IR0) {
1789                                 dev->ep[0].pio_irqs++;
1790                                 handle_ep0(dev);
1791                                 handled = 1;
1792                         }
1793
1794                         /* endpoint data transfers */
1795                         for (i = 0; i < 8; i++) {
1796                                 u32     tmp = 1 << i;
1797
1798                                 if (i && (usir0 & tmp)) {
1799                                         handle_ep(&dev->ep[i]);
1800                                         USIR0 |= tmp;
1801                                         handled = 1;
1802                                 }
1803 #ifndef CONFIG_USB_PXA25X_SMALL
1804                                 if (usir1 & tmp) {
1805                                         handle_ep(&dev->ep[i+8]);
1806                                         USIR1 |= tmp;
1807                                         handled = 1;
1808                                 }
1809 #endif
1810                         }
1811                 }
1812
1813                 /* we could also ask for 1 msec SOF (SIR) interrupts */
1814
1815         } while (handled);
1816         return IRQ_HANDLED;
1817 }
1818
1819 /*-------------------------------------------------------------------------*/
1820
1821 static void nop_release (struct device *dev)
1822 {
1823         DMSG("%s %s\n", __func__, dev_name(dev));
1824 }
1825
1826 /* this uses load-time allocation and initialization (instead of
1827  * doing it at run-time) to save code, eliminate fault paths, and
1828  * be more obviously correct.
1829  */
1830 static struct pxa25x_udc memory = {
1831         .gadget = {
1832                 .ops            = &pxa25x_udc_ops,
1833                 .ep0            = &memory.ep[0].ep,
1834                 .name           = driver_name,
1835                 .dev = {
1836                         .init_name      = "gadget",
1837                         .release        = nop_release,
1838                 },
1839         },
1840
1841         /* control endpoint */
1842         .ep[0] = {
1843                 .ep = {
1844                         .name           = ep0name,
1845                         .ops            = &pxa25x_ep_ops,
1846                         .maxpacket      = EP0_FIFO_SIZE,
1847                 },
1848                 .dev            = &memory,
1849                 .reg_udccs      = &UDCCS0,
1850                 .reg_uddr       = &UDDR0,
1851         },
1852
1853         /* first group of endpoints */
1854         .ep[1] = {
1855                 .ep = {
1856                         .name           = "ep1in-bulk",
1857                         .ops            = &pxa25x_ep_ops,
1858                         .maxpacket      = BULK_FIFO_SIZE,
1859                 },
1860                 .dev            = &memory,
1861                 .fifo_size      = BULK_FIFO_SIZE,
1862                 .bEndpointAddress = USB_DIR_IN | 1,
1863                 .bmAttributes   = USB_ENDPOINT_XFER_BULK,
1864                 .reg_udccs      = &UDCCS1,
1865                 .reg_uddr       = &UDDR1,
1866         },
1867         .ep[2] = {
1868                 .ep = {
1869                         .name           = "ep2out-bulk",
1870                         .ops            = &pxa25x_ep_ops,
1871                         .maxpacket      = BULK_FIFO_SIZE,
1872                 },
1873                 .dev            = &memory,
1874                 .fifo_size      = BULK_FIFO_SIZE,
1875                 .bEndpointAddress = 2,
1876                 .bmAttributes   = USB_ENDPOINT_XFER_BULK,
1877                 .reg_udccs      = &UDCCS2,
1878                 .reg_ubcr       = &UBCR2,
1879                 .reg_uddr       = &UDDR2,
1880         },
1881 #ifndef CONFIG_USB_PXA25X_SMALL
1882         .ep[3] = {
1883                 .ep = {
1884                         .name           = "ep3in-iso",
1885                         .ops            = &pxa25x_ep_ops,
1886                         .maxpacket      = ISO_FIFO_SIZE,
1887                 },
1888                 .dev            = &memory,
1889                 .fifo_size      = ISO_FIFO_SIZE,
1890                 .bEndpointAddress = USB_DIR_IN | 3,
1891                 .bmAttributes   = USB_ENDPOINT_XFER_ISOC,
1892                 .reg_udccs      = &UDCCS3,
1893                 .reg_uddr       = &UDDR3,
1894         },
1895         .ep[4] = {
1896                 .ep = {
1897                         .name           = "ep4out-iso",
1898                         .ops            = &pxa25x_ep_ops,
1899                         .maxpacket      = ISO_FIFO_SIZE,
1900                 },
1901                 .dev            = &memory,
1902                 .fifo_size      = ISO_FIFO_SIZE,
1903                 .bEndpointAddress = 4,
1904                 .bmAttributes   = USB_ENDPOINT_XFER_ISOC,
1905                 .reg_udccs      = &UDCCS4,
1906                 .reg_ubcr       = &UBCR4,
1907                 .reg_uddr       = &UDDR4,
1908         },
1909         .ep[5] = {
1910                 .ep = {
1911                         .name           = "ep5in-int",
1912                         .ops            = &pxa25x_ep_ops,
1913                         .maxpacket      = INT_FIFO_SIZE,
1914                 },
1915                 .dev            = &memory,
1916                 .fifo_size      = INT_FIFO_SIZE,
1917                 .bEndpointAddress = USB_DIR_IN | 5,
1918                 .bmAttributes   = USB_ENDPOINT_XFER_INT,
1919                 .reg_udccs      = &UDCCS5,
1920                 .reg_uddr       = &UDDR5,
1921         },
1922
1923         /* second group of endpoints */
1924         .ep[6] = {
1925                 .ep = {
1926                         .name           = "ep6in-bulk",
1927                         .ops            = &pxa25x_ep_ops,
1928                         .maxpacket      = BULK_FIFO_SIZE,
1929                 },
1930                 .dev            = &memory,
1931                 .fifo_size      = BULK_FIFO_SIZE,
1932                 .bEndpointAddress = USB_DIR_IN | 6,
1933                 .bmAttributes   = USB_ENDPOINT_XFER_BULK,
1934                 .reg_udccs      = &UDCCS6,
1935                 .reg_uddr       = &UDDR6,
1936         },
1937         .ep[7] = {
1938                 .ep = {
1939                         .name           = "ep7out-bulk",
1940                         .ops            = &pxa25x_ep_ops,
1941                         .maxpacket      = BULK_FIFO_SIZE,
1942                 },
1943                 .dev            = &memory,
1944                 .fifo_size      = BULK_FIFO_SIZE,
1945                 .bEndpointAddress = 7,
1946                 .bmAttributes   = USB_ENDPOINT_XFER_BULK,
1947                 .reg_udccs      = &UDCCS7,
1948                 .reg_ubcr       = &UBCR7,
1949                 .reg_uddr       = &UDDR7,
1950         },
1951         .ep[8] = {
1952                 .ep = {
1953                         .name           = "ep8in-iso",
1954                         .ops            = &pxa25x_ep_ops,
1955                         .maxpacket      = ISO_FIFO_SIZE,
1956                 },
1957                 .dev            = &memory,
1958                 .fifo_size      = ISO_FIFO_SIZE,
1959                 .bEndpointAddress = USB_DIR_IN | 8,
1960                 .bmAttributes   = USB_ENDPOINT_XFER_ISOC,
1961                 .reg_udccs      = &UDCCS8,
1962                 .reg_uddr       = &UDDR8,
1963         },
1964         .ep[9] = {
1965                 .ep = {
1966                         .name           = "ep9out-iso",
1967                         .ops            = &pxa25x_ep_ops,
1968                         .maxpacket      = ISO_FIFO_SIZE,
1969                 },
1970                 .dev            = &memory,
1971                 .fifo_size      = ISO_FIFO_SIZE,
1972                 .bEndpointAddress = 9,
1973                 .bmAttributes   = USB_ENDPOINT_XFER_ISOC,
1974                 .reg_udccs      = &UDCCS9,
1975                 .reg_ubcr       = &UBCR9,
1976                 .reg_uddr       = &UDDR9,
1977         },
1978         .ep[10] = {
1979                 .ep = {
1980                         .name           = "ep10in-int",
1981                         .ops            = &pxa25x_ep_ops,
1982                         .maxpacket      = INT_FIFO_SIZE,
1983                 },
1984                 .dev            = &memory,
1985                 .fifo_size      = INT_FIFO_SIZE,
1986                 .bEndpointAddress = USB_DIR_IN | 10,
1987                 .bmAttributes   = USB_ENDPOINT_XFER_INT,
1988                 .reg_udccs      = &UDCCS10,
1989                 .reg_uddr       = &UDDR10,
1990         },
1991
1992         /* third group of endpoints */
1993         .ep[11] = {
1994                 .ep = {
1995                         .name           = "ep11in-bulk",
1996                         .ops            = &pxa25x_ep_ops,
1997                         .maxpacket      = BULK_FIFO_SIZE,
1998                 },
1999                 .dev            = &memory,
2000                 .fifo_size      = BULK_FIFO_SIZE,
2001                 .bEndpointAddress = USB_DIR_IN | 11,
2002                 .bmAttributes   = USB_ENDPOINT_XFER_BULK,
2003                 .reg_udccs      = &UDCCS11,
2004                 .reg_uddr       = &UDDR11,
2005         },
2006         .ep[12] = {
2007                 .ep = {
2008                         .name           = "ep12out-bulk",
2009                         .ops            = &pxa25x_ep_ops,
2010                         .maxpacket      = BULK_FIFO_SIZE,
2011                 },
2012                 .dev            = &memory,
2013                 .fifo_size      = BULK_FIFO_SIZE,
2014                 .bEndpointAddress = 12,
2015                 .bmAttributes   = USB_ENDPOINT_XFER_BULK,
2016                 .reg_udccs      = &UDCCS12,
2017                 .reg_ubcr       = &UBCR12,
2018                 .reg_uddr       = &UDDR12,
2019         },
2020         .ep[13] = {
2021                 .ep = {
2022                         .name           = "ep13in-iso",
2023                         .ops            = &pxa25x_ep_ops,
2024                         .maxpacket      = ISO_FIFO_SIZE,
2025                 },
2026                 .dev            = &memory,
2027                 .fifo_size      = ISO_FIFO_SIZE,
2028                 .bEndpointAddress = USB_DIR_IN | 13,
2029                 .bmAttributes   = USB_ENDPOINT_XFER_ISOC,
2030                 .reg_udccs      = &UDCCS13,
2031                 .reg_uddr       = &UDDR13,
2032         },
2033         .ep[14] = {
2034                 .ep = {
2035                         .name           = "ep14out-iso",
2036                         .ops            = &pxa25x_ep_ops,
2037                         .maxpacket      = ISO_FIFO_SIZE,
2038                 },
2039                 .dev            = &memory,
2040                 .fifo_size      = ISO_FIFO_SIZE,
2041                 .bEndpointAddress = 14,
2042                 .bmAttributes   = USB_ENDPOINT_XFER_ISOC,
2043                 .reg_udccs      = &UDCCS14,
2044                 .reg_ubcr       = &UBCR14,
2045                 .reg_uddr       = &UDDR14,
2046         },
2047         .ep[15] = {
2048                 .ep = {
2049                         .name           = "ep15in-int",
2050                         .ops            = &pxa25x_ep_ops,
2051                         .maxpacket      = INT_FIFO_SIZE,
2052                 },
2053                 .dev            = &memory,
2054                 .fifo_size      = INT_FIFO_SIZE,
2055                 .bEndpointAddress = USB_DIR_IN | 15,
2056                 .bmAttributes   = USB_ENDPOINT_XFER_INT,
2057                 .reg_udccs      = &UDCCS15,
2058                 .reg_uddr       = &UDDR15,
2059         },
2060 #endif /* !CONFIG_USB_PXA25X_SMALL */
2061 };
2062
2063 #define CP15R0_VENDOR_MASK      0xffffe000
2064
2065 #if     defined(CONFIG_ARCH_PXA)
2066 #define CP15R0_XSCALE_VALUE     0x69052000      /* intel/arm/xscale */
2067
2068 #elif   defined(CONFIG_ARCH_IXP4XX)
2069 #define CP15R0_XSCALE_VALUE     0x69054000      /* intel/arm/ixp4xx */
2070
2071 #endif
2072
2073 #define CP15R0_PROD_MASK        0x000003f0
2074 #define PXA25x                  0x00000100      /* and PXA26x */
2075 #define PXA210                  0x00000120
2076
2077 #define CP15R0_REV_MASK         0x0000000f
2078
2079 #define CP15R0_PRODREV_MASK     (CP15R0_PROD_MASK | CP15R0_REV_MASK)
2080
2081 #define PXA255_A0               0x00000106      /* or PXA260_B1 */
2082 #define PXA250_C0               0x00000105      /* or PXA26x_B0 */
2083 #define PXA250_B2               0x00000104
2084 #define PXA250_B1               0x00000103      /* or PXA260_A0 */
2085 #define PXA250_B0               0x00000102
2086 #define PXA250_A1               0x00000101
2087 #define PXA250_A0               0x00000100
2088
2089 #define PXA210_C0               0x00000125
2090 #define PXA210_B2               0x00000124
2091 #define PXA210_B1               0x00000123
2092 #define PXA210_B0               0x00000122
2093 #define IXP425_A0               0x000001c1
2094 #define IXP425_B0               0x000001f1
2095 #define IXP465_AD               0x00000200
2096
2097 /*
2098  *      probe - binds to the platform device
2099  */
2100 static int __init pxa25x_udc_probe(struct platform_device *pdev)
2101 {
2102         struct pxa25x_udc *dev = &memory;
2103         int retval, irq;
2104         u32 chiprev;
2105
2106         /* insist on Intel/ARM/XScale */
2107         asm("mrc%? p15, 0, %0, c0, c0" : "=r" (chiprev));
2108         if ((chiprev & CP15R0_VENDOR_MASK) != CP15R0_XSCALE_VALUE) {
2109                 pr_err("%s: not XScale!\n", driver_name);
2110                 return -ENODEV;
2111         }
2112
2113         /* trigger chiprev-specific logic */
2114         switch (chiprev & CP15R0_PRODREV_MASK) {
2115 #if     defined(CONFIG_ARCH_PXA)
2116         case PXA255_A0:
2117                 dev->has_cfr = 1;
2118                 break;
2119         case PXA250_A0:
2120         case PXA250_A1:
2121                 /* A0/A1 "not released"; ep 13, 15 unusable */
2122                 /* fall through */
2123         case PXA250_B2: case PXA210_B2:
2124         case PXA250_B1: case PXA210_B1:
2125         case PXA250_B0: case PXA210_B0:
2126                 /* OUT-DMA is broken ... */
2127                 /* fall through */
2128         case PXA250_C0: case PXA210_C0:
2129                 break;
2130 #elif   defined(CONFIG_ARCH_IXP4XX)
2131         case IXP425_A0:
2132         case IXP425_B0:
2133         case IXP465_AD:
2134                 dev->has_cfr = 1;
2135                 break;
2136 #endif
2137         default:
2138                 pr_err("%s: unrecognized processor: %08x\n",
2139                         driver_name, chiprev);
2140                 /* iop3xx, ixp4xx, ... */
2141                 return -ENODEV;
2142         }
2143
2144         irq = platform_get_irq(pdev, 0);
2145         if (irq < 0)
2146                 return -ENODEV;
2147
2148         dev->clk = clk_get(&pdev->dev, NULL);
2149         if (IS_ERR(dev->clk)) {
2150                 retval = PTR_ERR(dev->clk);
2151                 goto err_clk;
2152         }
2153
2154         pr_debug("%s: IRQ %d%s%s\n", driver_name, irq,
2155                 dev->has_cfr ? "" : " (!cfr)",
2156                 SIZE_STR "(pio)"
2157                 );
2158
2159         /* other non-static parts of init */
2160         dev->dev = &pdev->dev;
2161         dev->mach = pdev->dev.platform_data;
2162
2163         dev->transceiver = usb_get_phy(USB_PHY_TYPE_USB2);
2164
2165         if (gpio_is_valid(dev->mach->gpio_pullup)) {
2166                 if ((retval = gpio_request(dev->mach->gpio_pullup,
2167                                 "pca25x_udc GPIO PULLUP"))) {
2168                         dev_dbg(&pdev->dev,
2169                                 "can't get pullup gpio %d, err: %d\n",
2170                                 dev->mach->gpio_pullup, retval);
2171                         goto err_gpio_pullup;
2172                 }
2173                 gpio_direction_output(dev->mach->gpio_pullup, 0);
2174         }
2175
2176         init_timer(&dev->timer);
2177         dev->timer.function = udc_watchdog;
2178         dev->timer.data = (unsigned long) dev;
2179
2180         device_initialize(&dev->gadget.dev);
2181         dev->gadget.dev.parent = &pdev->dev;
2182         dev->gadget.dev.dma_mask = pdev->dev.dma_mask;
2183
2184         the_controller = dev;
2185         platform_set_drvdata(pdev, dev);
2186
2187         udc_disable(dev);
2188         udc_reinit(dev);
2189
2190         dev->vbus = 0;
2191
2192         /* irq setup after old hardware state is cleaned up */
2193         retval = request_irq(irq, pxa25x_udc_irq,
2194                         0, driver_name, dev);
2195         if (retval != 0) {
2196                 pr_err("%s: can't get irq %d, err %d\n",
2197                         driver_name, irq, retval);
2198                 goto err_irq1;
2199         }
2200         dev->got_irq = 1;
2201
2202 #ifdef CONFIG_ARCH_LUBBOCK
2203         if (machine_is_lubbock()) {
2204                 retval = request_irq(LUBBOCK_USB_DISC_IRQ, lubbock_vbus_irq,
2205                                      0, driver_name, dev);
2206                 if (retval != 0) {
2207                         pr_err("%s: can't get irq %i, err %d\n",
2208                                 driver_name, LUBBOCK_USB_DISC_IRQ, retval);
2209                         goto err_irq_lub;
2210                 }
2211                 retval = request_irq(LUBBOCK_USB_IRQ, lubbock_vbus_irq,
2212                                      0, driver_name, dev);
2213                 if (retval != 0) {
2214                         pr_err("%s: can't get irq %i, err %d\n",
2215                                 driver_name, LUBBOCK_USB_IRQ, retval);
2216                         goto lubbock_fail0;
2217                 }
2218         } else
2219 #endif
2220         create_debug_files(dev);
2221
2222         retval = usb_add_gadget_udc(&pdev->dev, &dev->gadget);
2223         if (!retval)
2224                 return retval;
2225
2226         remove_debug_files(dev);
2227 #ifdef  CONFIG_ARCH_LUBBOCK
2228 lubbock_fail0:
2229         free_irq(LUBBOCK_USB_DISC_IRQ, dev);
2230  err_irq_lub:
2231         free_irq(irq, dev);
2232 #endif
2233  err_irq1:
2234         if (gpio_is_valid(dev->mach->gpio_pullup))
2235                 gpio_free(dev->mach->gpio_pullup);
2236  err_gpio_pullup:
2237         if (!IS_ERR_OR_NULL(dev->transceiver)) {
2238                 usb_put_phy(dev->transceiver);
2239                 dev->transceiver = NULL;
2240         }
2241         clk_put(dev->clk);
2242  err_clk:
2243         return retval;
2244 }
2245
2246 static void pxa25x_udc_shutdown(struct platform_device *_dev)
2247 {
2248         pullup_off();
2249 }
2250
2251 static int __exit pxa25x_udc_remove(struct platform_device *pdev)
2252 {
2253         struct pxa25x_udc *dev = platform_get_drvdata(pdev);
2254
2255         usb_del_gadget_udc(&dev->gadget);
2256         if (dev->driver)
2257                 return -EBUSY;
2258
2259         dev->pullup = 0;
2260         pullup(dev);
2261
2262         remove_debug_files(dev);
2263
2264         if (dev->got_irq) {
2265                 free_irq(platform_get_irq(pdev, 0), dev);
2266                 dev->got_irq = 0;
2267         }
2268 #ifdef CONFIG_ARCH_LUBBOCK
2269         if (machine_is_lubbock()) {
2270                 free_irq(LUBBOCK_USB_DISC_IRQ, dev);
2271                 free_irq(LUBBOCK_USB_IRQ, dev);
2272         }
2273 #endif
2274         if (gpio_is_valid(dev->mach->gpio_pullup))
2275                 gpio_free(dev->mach->gpio_pullup);
2276
2277         clk_put(dev->clk);
2278
2279         if (!IS_ERR_OR_NULL(dev->transceiver)) {
2280                 usb_put_phy(dev->transceiver);
2281                 dev->transceiver = NULL;
2282         }
2283
2284         platform_set_drvdata(pdev, NULL);
2285         the_controller = NULL;
2286         return 0;
2287 }
2288
2289 /*-------------------------------------------------------------------------*/
2290
2291 #ifdef  CONFIG_PM
2292
2293 /* USB suspend (controlled by the host) and system suspend (controlled
2294  * by the PXA) don't necessarily work well together.  If USB is active,
2295  * the 48 MHz clock is required; so the system can't enter 33 MHz idle
2296  * mode, or any deeper PM saving state.
2297  *
2298  * For now, we punt and forcibly disconnect from the USB host when PXA
2299  * enters any suspend state.  While we're disconnected, we always disable
2300  * the 48MHz USB clock ... allowing PXA sleep and/or 33 MHz idle states.
2301  * Boards without software pullup control shouldn't use those states.
2302  * VBUS IRQs should probably be ignored so that the PXA device just acts
2303  * "dead" to USB hosts until system resume.
2304  */
2305 static int pxa25x_udc_suspend(struct platform_device *dev, pm_message_t state)
2306 {
2307         struct pxa25x_udc       *udc = platform_get_drvdata(dev);
2308         unsigned long flags;
2309
2310         if (!gpio_is_valid(udc->mach->gpio_pullup) && !udc->mach->udc_command)
2311                 WARNING("USB host won't detect disconnect!\n");
2312         udc->suspended = 1;
2313
2314         local_irq_save(flags);
2315         pullup(udc);
2316         local_irq_restore(flags);
2317
2318         return 0;
2319 }
2320
2321 static int pxa25x_udc_resume(struct platform_device *dev)
2322 {
2323         struct pxa25x_udc       *udc = platform_get_drvdata(dev);
2324         unsigned long flags;
2325
2326         udc->suspended = 0;
2327         local_irq_save(flags);
2328         pullup(udc);
2329         local_irq_restore(flags);
2330
2331         return 0;
2332 }
2333
2334 #else
2335 #define pxa25x_udc_suspend      NULL
2336 #define pxa25x_udc_resume       NULL
2337 #endif
2338
2339 /*-------------------------------------------------------------------------*/
2340
2341 static struct platform_driver udc_driver = {
2342         .shutdown       = pxa25x_udc_shutdown,
2343         .remove         = __exit_p(pxa25x_udc_remove),
2344         .suspend        = pxa25x_udc_suspend,
2345         .resume         = pxa25x_udc_resume,
2346         .driver         = {
2347                 .owner  = THIS_MODULE,
2348                 .name   = "pxa25x-udc",
2349         },
2350 };
2351
2352 static int __init udc_init(void)
2353 {
2354         pr_info("%s: version %s\n", driver_name, DRIVER_VERSION);
2355         return platform_driver_probe(&udc_driver, pxa25x_udc_probe);
2356 }
2357 module_init(udc_init);
2358
2359 static void __exit udc_exit(void)
2360 {
2361         platform_driver_unregister(&udc_driver);
2362 }
2363 module_exit(udc_exit);
2364
2365 MODULE_DESCRIPTION(DRIVER_DESC);
2366 MODULE_AUTHOR("Frank Becker, Robert Schwebel, David Brownell");
2367 MODULE_LICENSE("GPL");
2368 MODULE_ALIAS("platform:pxa25x-udc");