drivers/spi/spi_bfin5xx.c

   1 /*
   2  * Blackfin On-Chip SPI Driver
   3  *
   4  * Copyright 2004-2010 Analog Devices Inc.
   5  *
   6  * Enter bugs at http://blackfin.uclinux.org/
   7  *
   8  * Licensed under the GPL-2 or later.
   9  */
  10
  11 #include <linux/init.h>
  12 #include <linux/module.h>
  13 #include <linux/delay.h>
  14 #include <linux/device.h>
  15 #include <linux/slab.h>
  16 #include <linux/io.h>
  17 #include <linux/ioport.h>
  18 #include <linux/irq.h>
  19 #include <linux/errno.h>
  20 #include <linux/interrupt.h>
  21 #include <linux/platform_device.h>
  22 #include <linux/dma-mapping.h>
  23 #include <linux/spi/spi.h>
  24 #include <linux/workqueue.h>
  25
  26 #include <asm/dma.h>
  27 #include <asm/portmux.h>
  28 #include <asm/bfin5xx_spi.h>
  29 #include <asm/cacheflush.h>
  30
  31 #define DRV_NAME        "bfin-spi"
  32 #define DRV_AUTHOR      "Bryan Wu, Luke Yang"
  33 #define DRV_DESC        "Blackfin on-chip SPI Controller Driver"
  34 #define DRV_VERSION     "1.0"
  35
  36 MODULE_AUTHOR(DRV_AUTHOR);
  37 MODULE_DESCRIPTION(DRV_DESC);
  38 MODULE_LICENSE("GPL");
  39
  40 #define START_STATE     ((void *)0)
  41 #define RUNNING_STATE   ((void *)1)
  42 #define DONE_STATE      ((void *)2)
  43 #define ERROR_STATE     ((void *)-1)
  44
  45 struct bfin_spi_master_data;
  46
  47 struct bfin_spi_transfer_ops {
  48         void (*write) (struct bfin_spi_master_data *);
  49         void (*read) (struct bfin_spi_master_data *);
  50         void (*duplex) (struct bfin_spi_master_data *);
  51 };
  52
  53 struct bfin_spi_master_data {
  54         /* Driver model hookup */
  55         struct platform_device *pdev;
  56
  57         /* SPI framework hookup */
  58         struct spi_master *master;
  59
  60         /* Regs base of SPI controller */
  61         void __iomem *regs_base;
  62
  63         /* Pin request list */
  64         u16 *pin_req;
  65
  66         /* BFIN hookup */
  67         struct bfin5xx_spi_master *master_info;
  68
  69         /* Driver message queue */
  70         struct workqueue_struct *workqueue;
  71         struct work_struct pump_messages;
  72         spinlock_t lock;
  73         struct list_head queue;
  74         int busy;
  75         bool running;
  76
  77         /* Message Transfer pump */
  78         struct tasklet_struct pump_transfers;
  79
  80         /* Current message transfer state info */
  81         struct spi_message *cur_msg;
  82         struct spi_transfer *cur_transfer;
  83         struct bfin_spi_slave_data *cur_chip;
  84         size_t len_in_bytes;
  85         size_t len;
  86         void *tx;
  87         void *tx_end;
  88         void *rx;
  89         void *rx_end;
  90
  91         /* DMA stuffs */
  92         int dma_channel;
  93         int dma_mapped;
  94         int dma_requested;
  95         dma_addr_t rx_dma;
  96         dma_addr_t tx_dma;
  97
  98         int irq_requested;
  99         int spi_irq;
 100
 101         size_t rx_map_len;
 102         size_t tx_map_len;
 103         u8 n_bytes;
 104         u16 ctrl_reg;
 105         u16 flag_reg;
 106
 107         int cs_change;
 108         const struct bfin_spi_transfer_ops *ops;
 109 };
 110
 111 struct bfin_spi_slave_data {
 112         u16 ctl_reg;
 113         u16 baud;
 114         u16 flag;
 115
 116         u8 chip_select_num;
 117         u8 enable_dma;
 118         u16 cs_chg_udelay;      /* Some devices require > 255usec delay */
 119         u32 cs_gpio;
 120         u16 idle_tx_val;
 121         u8 pio_interrupt;       /* use spi data irq */
 122         const struct bfin_spi_transfer_ops *ops;
 123 };
 124
 125 #define DEFINE_SPI_REG(reg, off) \
 126 static inline u16 read_##reg(struct bfin_spi_master_data *drv_data) \
 127         { return bfin_read16(drv_data->regs_base + off); } \
 128 static inline void write_##reg(struct bfin_spi_master_data *drv_data, u16 v) \
 129         { bfin_write16(drv_data->regs_base + off, v); }
 130
 131 DEFINE_SPI_REG(CTRL, 0x00)
 132 DEFINE_SPI_REG(FLAG, 0x04)
 133 DEFINE_SPI_REG(STAT, 0x08)
 134 DEFINE_SPI_REG(TDBR, 0x0C)
 135 DEFINE_SPI_REG(RDBR, 0x10)
 136 DEFINE_SPI_REG(BAUD, 0x14)
 137 DEFINE_SPI_REG(SHAW, 0x18)
 138
 139 static void bfin_spi_enable(struct bfin_spi_master_data *drv_data)
 140 {
 141         u16 cr;
 142
 143         cr = read_CTRL(drv_data);
 144         write_CTRL(drv_data, (cr | BIT_CTL_ENABLE));
 145 }
 146
 147 static void bfin_spi_disable(struct bfin_spi_master_data *drv_data)
 148 {
 149         u16 cr;
 150
 151         cr = read_CTRL(drv_data);
 152         write_CTRL(drv_data, (cr & (~BIT_CTL_ENABLE)));
 153 }
 154
 155 /* Caculate the SPI_BAUD register value based on input HZ */
 156 static u16 hz_to_spi_baud(u32 speed_hz)
 157 {
 158         u_long sclk = get_sclk();
 159         u16 spi_baud = (sclk / (2 * speed_hz));
 160
 161         if ((sclk % (2 * speed_hz)) > 0)
 162                 spi_baud++;
 163
 164         if (spi_baud < MIN_SPI_BAUD_VAL)
 165                 spi_baud = MIN_SPI_BAUD_VAL;
 166
 167         return spi_baud;
 168 }
 169
 170 static int bfin_spi_flush(struct bfin_spi_master_data *drv_data)
 171 {
 172         unsigned long limit = loops_per_jiffy << 1;
 173
 174         /* wait for stop and clear stat */
 175         while (!(read_STAT(drv_data) & BIT_STAT_SPIF) && --limit)
 176                 cpu_relax();
 177
 178         write_STAT(drv_data, BIT_STAT_CLR);
 179
 180         return limit;
 181 }
 182
 183 /* Chip select operation functions for cs_change flag */
 184 static void bfin_spi_cs_active(struct bfin_spi_master_data *drv_data, struct bfin_spi_slave_data *chip)
 185 {
 186         if (likely(chip->chip_select_num < MAX_CTRL_CS)) {
 187                 u16 flag = read_FLAG(drv_data);
 188
 189                 flag &= ~chip->flag;
 190
 191                 write_FLAG(drv_data, flag);
 192         } else {
 193                 gpio_set_value(chip->cs_gpio, 0);
 194         }
 195 }
 196
 197 static void bfin_spi_cs_deactive(struct bfin_spi_master_data *drv_data,
 198                                  struct bfin_spi_slave_data *chip)
 199 {
 200         if (likely(chip->chip_select_num < MAX_CTRL_CS)) {
 201                 u16 flag = read_FLAG(drv_data);
 202
 203                 flag |= chip->flag;
 204
 205                 write_FLAG(drv_data, flag);
 206         } else {
 207                 gpio_set_value(chip->cs_gpio, 1);
 208         }
 209
 210         /* Move delay here for consistency */
 211         if (chip->cs_chg_udelay)
 212                 udelay(chip->cs_chg_udelay);
 213 }
 214
 215 /* enable or disable the pin muxed by GPIO and SPI CS to work as SPI CS */
 216 static inline void bfin_spi_cs_enable(struct bfin_spi_master_data *drv_data,
 217                                       struct bfin_spi_slave_data *chip)
 218 {
 219         if (chip->chip_select_num < MAX_CTRL_CS) {
 220                 u16 flag = read_FLAG(drv_data);
 221
 222                 flag |= (chip->flag >> 8);
 223
 224                 write_FLAG(drv_data, flag);
 225         }
 226 }
 227
 228 static inline void bfin_spi_cs_disable(struct bfin_spi_master_data *drv_data,
 229                                        struct bfin_spi_slave_data *chip)
 230 {
 231         if (chip->chip_select_num < MAX_CTRL_CS) {
 232                 u16 flag = read_FLAG(drv_data);
 233
 234                 flag &= ~(chip->flag >> 8);
 235
 236                 write_FLAG(drv_data, flag);
 237         }
 238 }
 239
 240 /* stop controller and re-config current chip*/
 241 static void bfin_spi_restore_state(struct bfin_spi_master_data *drv_data)
 242 {
 243         struct bfin_spi_slave_data *chip = drv_data->cur_chip;
 244
 245         /* Clear status and disable clock */
 246         write_STAT(drv_data, BIT_STAT_CLR);
 247         bfin_spi_disable(drv_data);
 248         dev_dbg(&drv_data->pdev->dev, "restoring spi ctl state\n");
 249
 250         SSYNC();
 251
 252         /* Load the registers */
 253         write_CTRL(drv_data, chip->ctl_reg);
 254         write_BAUD(drv_data, chip->baud);
 255
 256         bfin_spi_enable(drv_data);
 257         bfin_spi_cs_active(drv_data, chip);
 258 }
 259
 260 /* used to kick off transfer in rx mode and read unwanted RX data */
 261 static inline void bfin_spi_dummy_read(struct bfin_spi_master_data *drv_data)
 262 {
 263         (void) read_RDBR(drv_data);
 264 }
 265
 266 static void bfin_spi_u8_writer(struct bfin_spi_master_data *drv_data)
 267 {
 268         /* clear RXS (we check for RXS inside the loop) */
 269         bfin_spi_dummy_read(drv_data);
 270
 271         while (drv_data->tx < drv_data->tx_end) {
 272                 write_TDBR(drv_data, (*(u8 *) (drv_data->tx++)));
 273                 /* wait until transfer finished.
 274                    checking SPIF or TXS may not guarantee transfer completion */
 275                 while (!(read_STAT(drv_data) & BIT_STAT_RXS))
 276                         cpu_relax();
 277                 /* discard RX data and clear RXS */
 278                 bfin_spi_dummy_read(drv_data);
 279         }
 280 }
 281
 282 static void bfin_spi_u8_reader(struct bfin_spi_master_data *drv_data)
 283 {
 284         u16 tx_val = drv_data->cur_chip->idle_tx_val;
 285
 286         /* discard old RX data and clear RXS */
 287         bfin_spi_dummy_read(drv_data);
 288
 289         while (drv_data->rx < drv_data->rx_end) {
 290                 write_TDBR(drv_data, tx_val);
 291                 while (!(read_STAT(drv_data) & BIT_STAT_RXS))
 292                         cpu_relax();
 293                 *(u8 *) (drv_data->rx++) = read_RDBR(drv_data);
 294         }
 295 }
 296
 297 static void bfin_spi_u8_duplex(struct bfin_spi_master_data *drv_data)
 298 {
 299         /* discard old RX data and clear RXS */
 300         bfin_spi_dummy_read(drv_data);
 301
 302         while (drv_data->rx < drv_data->rx_end) {
 303                 write_TDBR(drv_data, (*(u8 *) (drv_data->tx++)));
 304                 while (!(read_STAT(drv_data) & BIT_STAT_RXS))
 305                         cpu_relax();
 306                 *(u8 *) (drv_data->rx++) = read_RDBR(drv_data);
 307         }
 308 }
 309
 310 static const struct bfin_spi_transfer_ops bfin_bfin_spi_transfer_ops_u8 = {
 311         .write  = bfin_spi_u8_writer,
 312         .read   = bfin_spi_u8_reader,
 313         .duplex = bfin_spi_u8_duplex,
 314 };
 315
 316 static void bfin_spi_u16_writer(struct bfin_spi_master_data *drv_data)
 317 {
 318         /* clear RXS (we check for RXS inside the loop) */
 319         bfin_spi_dummy_read(drv_data);
 320
 321         while (drv_data->tx < drv_data->tx_end) {
 322                 write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
 323                 drv_data->tx += 2;
 324                 /* wait until transfer finished.
 325                    checking SPIF or TXS may not guarantee transfer completion */
 326                 while (!(read_STAT(drv_data) & BIT_STAT_RXS))
 327                         cpu_relax();
 328                 /* discard RX data and clear RXS */
 329                 bfin_spi_dummy_read(drv_data);
 330         }
 331 }
 332
 333 static void bfin_spi_u16_reader(struct bfin_spi_master_data *drv_data)
 334 {
 335         u16 tx_val = drv_data->cur_chip->idle_tx_val;
 336
 337         /* discard old RX data and clear RXS */
 338         bfin_spi_dummy_read(drv_data);
 339
 340         while (drv_data->rx < drv_data->rx_end) {
 341                 write_TDBR(drv_data, tx_val);
 342                 while (!(read_STAT(drv_data) & BIT_STAT_RXS))
 343                         cpu_relax();
 344                 *(u16 *) (drv_data->rx) = read_RDBR(drv_data);
 345                 drv_data->rx += 2;
 346         }
 347 }
 348
 349 static void bfin_spi_u16_duplex(struct bfin_spi_master_data *drv_data)
 350 {
 351         /* discard old RX data and clear RXS */
 352         bfin_spi_dummy_read(drv_data);
 353
 354         while (drv_data->rx < drv_data->rx_end) {
 355                 write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
 356                 drv_data->tx += 2;
 357                 while (!(read_STAT(drv_data) & BIT_STAT_RXS))
 358                         cpu_relax();
 359                 *(u16 *) (drv_data->rx) = read_RDBR(drv_data);
 360                 drv_data->rx += 2;
 361         }
 362 }
 363
 364 static const struct bfin_spi_transfer_ops bfin_bfin_spi_transfer_ops_u16 = {
 365         .write  = bfin_spi_u16_writer,
 366         .read   = bfin_spi_u16_reader,
 367         .duplex = bfin_spi_u16_duplex,
 368 };
 369
 370 /* test if there is more transfer to be done */
 371 static void *bfin_spi_next_transfer(struct bfin_spi_master_data *drv_data)
 372 {
 373         struct spi_message *msg = drv_data->cur_msg;
 374         struct spi_transfer *trans = drv_data->cur_transfer;
 375
 376         /* Move to next transfer */
 377         if (trans->transfer_list.next != &msg->transfers) {
 378                 drv_data->cur_transfer =
 379                     list_entry(trans->transfer_list.next,
 380                                struct spi_transfer, transfer_list);
 381                 return RUNNING_STATE;
 382         } else
 383                 return DONE_STATE;
 384 }
 385
 386 /*
 387  * caller already set message->status;
 388  * dma and pio irqs are blocked give finished message back
 389  */
 390 static void bfin_spi_giveback(struct bfin_spi_master_data *drv_data)
 391 {
 392         struct bfin_spi_slave_data *chip = drv_data->cur_chip;
 393         struct spi_transfer *last_transfer;
 394         unsigned long flags;
 395         struct spi_message *msg;
 396
 397         spin_lock_irqsave(&drv_data->lock, flags);
 398         msg = drv_data->cur_msg;
 399         drv_data->cur_msg = NULL;
 400         drv_data->cur_transfer = NULL;
 401         drv_data->cur_chip = NULL;
 402         queue_work(drv_data->workqueue, &drv_data->pump_messages);
 403         spin_unlock_irqrestore(&drv_data->lock, flags);
 404
 405         last_transfer = list_entry(msg->transfers.prev,
 406                                    struct spi_transfer, transfer_list);
 407
 408         msg->state = NULL;
 409
 410         if (!drv_data->cs_change)
 411                 bfin_spi_cs_deactive(drv_data, chip);
 412
 413         /* Not stop spi in autobuffer mode */
 414         if (drv_data->tx_dma != 0xFFFF)
 415                 bfin_spi_disable(drv_data);
 416
 417         if (msg->complete)
 418                 msg->complete(msg->context);
 419 }
 420
 421 /* spi data irq handler */
 422 static irqreturn_t bfin_spi_pio_irq_handler(int irq, void *dev_id)
 423 {
 424         struct bfin_spi_master_data *drv_data = dev_id;
 425         struct bfin_spi_slave_data *chip = drv_data->cur_chip;
 426         struct spi_message *msg = drv_data->cur_msg;
 427         int n_bytes = drv_data->n_bytes;
 428
 429         /* wait until transfer finished. */
 430         while (!(read_STAT(drv_data) & BIT_STAT_RXS))
 431                 cpu_relax();
 432
 433         if ((drv_data->tx && drv_data->tx >= drv_data->tx_end) ||
 434                 (drv_data->rx && drv_data->rx >= (drv_data->rx_end - n_bytes))) {
 435                 /* last read */
 436                 if (drv_data->rx) {
 437                         dev_dbg(&drv_data->pdev->dev, "last read\n");
 438                         if (n_bytes == 2)
 439                                 *(u16 *) (drv_data->rx) = read_RDBR(drv_data);
 440                         else if (n_bytes == 1)
 441                                 *(u8 *) (drv_data->rx) = read_RDBR(drv_data);
 442                         drv_data->rx += n_bytes;
 443                 }
 444
 445                 msg->actual_length += drv_data->len_in_bytes;
 446                 if (drv_data->cs_change)
 447                         bfin_spi_cs_deactive(drv_data, chip);
 448                 /* Move to next transfer */
 449                 msg->state = bfin_spi_next_transfer(drv_data);
 450
 451                 disable_irq_nosync(drv_data->spi_irq);
 452
 453                 /* Schedule transfer tasklet */
 454                 tasklet_schedule(&drv_data->pump_transfers);
 455                 return IRQ_HANDLED;
 456         }
 457
 458         if (drv_data->rx && drv_data->tx) {
 459                 /* duplex */
 460                 dev_dbg(&drv_data->pdev->dev, "duplex: write_TDBR\n");
 461                 if (drv_data->n_bytes == 2) {
 462                         *(u16 *) (drv_data->rx) = read_RDBR(drv_data);
 463                         write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
 464                 } else if (drv_data->n_bytes == 1) {
 465                         *(u8 *) (drv_data->rx) = read_RDBR(drv_data);
 466                         write_TDBR(drv_data, (*(u8 *) (drv_data->tx)));
 467                 }
 468         } else if (drv_data->rx) {
 469                 /* read */
 470                 dev_dbg(&drv_data->pdev->dev, "read: write_TDBR\n");
 471                 if (drv_data->n_bytes == 2)
 472                         *(u16 *) (drv_data->rx) = read_RDBR(drv_data);
 473                 else if (drv_data->n_bytes == 1)
 474                         *(u8 *) (drv_data->rx) = read_RDBR(drv_data);
 475                 write_TDBR(drv_data, chip->idle_tx_val);
 476         } else if (drv_data->tx) {
 477                 /* write */
 478                 dev_dbg(&drv_data->pdev->dev, "write: write_TDBR\n");
 479                 bfin_spi_dummy_read(drv_data);
 480                 if (drv_data->n_bytes == 2)
 481                         write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
 482                 else if (drv_data->n_bytes == 1)
 483                         write_TDBR(drv_data, (*(u8 *) (drv_data->tx)));
 484         }
 485
 486         if (drv_data->tx)
 487                 drv_data->tx += n_bytes;
 488         if (drv_data->rx)
 489                 drv_data->rx += n_bytes;
 490
 491         return IRQ_HANDLED;
 492 }
 493
 494 static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
 495 {
 496         struct bfin_spi_master_data *drv_data = dev_id;
 497         struct bfin_spi_slave_data *chip = drv_data->cur_chip;
 498         struct spi_message *msg = drv_data->cur_msg;
 499         unsigned long timeout;
 500         unsigned short dmastat = get_dma_curr_irqstat(drv_data->dma_channel);
 501         u16 spistat = read_STAT(drv_data);
 502
 503         dev_dbg(&drv_data->pdev->dev,
 504                 "in dma_irq_handler dmastat:0x%x spistat:0x%x\n",
 505                 dmastat, spistat);
 506
 507         if (drv_data->rx != NULL) {
 508                 u16 cr = read_CTRL(drv_data);
 509                 /* discard old RX data and clear RXS */
 510                 bfin_spi_dummy_read(drv_data);
 511                 write_CTRL(drv_data, cr & ~BIT_CTL_ENABLE); /* Disable SPI */
 512                 write_CTRL(drv_data, cr & ~BIT_CTL_TIMOD); /* Restore State */
 513                 write_STAT(drv_data, BIT_STAT_CLR); /* Clear Status */
 514         }
 515
 516         clear_dma_irqstat(drv_data->dma_channel);
 517
 518         /*
 519          * wait for the last transaction shifted out.  HRM states:
 520          * at this point there may still be data in the SPI DMA FIFO waiting
 521          * to be transmitted ... software needs to poll TXS in the SPI_STAT
 522          * register until it goes low for 2 successive reads
 523          */
 524         if (drv_data->tx != NULL) {
 525                 while ((read_STAT(drv_data) & BIT_STAT_TXS) ||
 526                        (read_STAT(drv_data) & BIT_STAT_TXS))
 527                         cpu_relax();
 528         }
 529
 530         dev_dbg(&drv_data->pdev->dev,
 531                 "in dma_irq_handler dmastat:0x%x spistat:0x%x\n",
 532                 dmastat, read_STAT(drv_data));
 533
 534         timeout = jiffies + HZ;
 535         while (!(read_STAT(drv_data) & BIT_STAT_SPIF))
 536                 if (!time_before(jiffies, timeout)) {
 537                         dev_warn(&drv_data->pdev->dev, "timeout waiting for SPIF");
 538                         break;
 539                 } else
 540                         cpu_relax();
 541
 542         if ((dmastat & DMA_ERR) && (spistat & BIT_STAT_RBSY)) {
 543                 msg->state = ERROR_STATE;
 544                 dev_err(&drv_data->pdev->dev, "dma receive: fifo/buffer overflow\n");
 545         } else {
 546                 msg->actual_length += drv_data->len_in_bytes;
 547
 548                 if (drv_data->cs_change)
 549                         bfin_spi_cs_deactive(drv_data, chip);
 550
 551                 /* Move to next transfer */
 552                 msg->state = bfin_spi_next_transfer(drv_data);
 553         }
 554
 555         /* Schedule transfer tasklet */
 556         tasklet_schedule(&drv_data->pump_transfers);
 557
 558         /* free the irq handler before next transfer */
 559         dev_dbg(&drv_data->pdev->dev,
 560                 "disable dma channel irq%d\n",
 561                 drv_data->dma_channel);
 562         dma_disable_irq_nosync(drv_data->dma_channel);
 563
 564         return IRQ_HANDLED;
 565 }
 566
 567 static void bfin_spi_pump_transfers(unsigned long data)
 568 {
 569         struct bfin_spi_master_data *drv_data = (struct bfin_spi_master_data *)data;
 570         struct spi_message *message = NULL;
 571         struct spi_transfer *transfer = NULL;
 572         struct spi_transfer *previous = NULL;
 573         struct bfin_spi_slave_data *chip = NULL;
 574         unsigned int bits_per_word;
 575         u16 cr, cr_width, dma_width, dma_config;
 576         u32 tranf_success = 1;
 577         u8 full_duplex = 0;
 578
 579         /* Get current state information */
 580         message = drv_data->cur_msg;
 581         transfer = drv_data->cur_transfer;
 582         chip = drv_data->cur_chip;
 583
 584         /*
 585          * if msg is error or done, report it back using complete() callback
 586          */
 587
 588          /* Handle for abort */
 589         if (message->state == ERROR_STATE) {
 590                 dev_dbg(&drv_data->pdev->dev, "transfer: we've hit an error\n");
 591                 message->status = -EIO;
 592                 bfin_spi_giveback(drv_data);
 593                 return;
 594         }
 595
 596         /* Handle end of message */
 597         if (message->state == DONE_STATE) {
 598                 dev_dbg(&drv_data->pdev->dev, "transfer: all done!\n");
 599                 message->status = 0;
 600                 bfin_spi_giveback(drv_data);
 601                 return;
 602         }
 603
 604         /* Delay if requested at end of transfer */
 605         if (message->state == RUNNING_STATE) {
 606                 dev_dbg(&drv_data->pdev->dev, "transfer: still running ...\n");
 607                 previous = list_entry(transfer->transfer_list.prev,
 608                                       struct spi_transfer, transfer_list);
 609                 if (previous->delay_usecs)
 610                         udelay(previous->delay_usecs);
 611         }
 612
 613         /* Flush any existing transfers that may be sitting in the hardware */
 614         if (bfin_spi_flush(drv_data) == 0) {
 615                 dev_err(&drv_data->pdev->dev, "pump_transfers: flush failed\n");
 616                 message->status = -EIO;
 617                 bfin_spi_giveback(drv_data);
 618                 return;
 619         }
 620
 621         if (transfer->len == 0) {
 622                 /* Move to next transfer of this msg */
 623                 message->state = bfin_spi_next_transfer(drv_data);
 624                 /* Schedule next transfer tasklet */
 625                 tasklet_schedule(&drv_data->pump_transfers);
 626         }
 627
 628         if (transfer->tx_buf != NULL) {
 629                 drv_data->tx = (void *)transfer->tx_buf;
 630                 drv_data->tx_end = drv_data->tx + transfer->len;
 631                 dev_dbg(&drv_data->pdev->dev, "tx_buf is %p, tx_end is %p\n",
 632                         transfer->tx_buf, drv_data->tx_end);
 633         } else {
 634                 drv_data->tx = NULL;
 635         }
 636
 637         if (transfer->rx_buf != NULL) {
 638                 full_duplex = transfer->tx_buf != NULL;
 639                 drv_data->rx = transfer->rx_buf;
 640                 drv_data->rx_end = drv_data->rx + transfer->len;
 641                 dev_dbg(&drv_data->pdev->dev, "rx_buf is %p, rx_end is %p\n",
 642                         transfer->rx_buf, drv_data->rx_end);
 643         } else {
 644                 drv_data->rx = NULL;
 645         }
 646
 647         drv_data->rx_dma = transfer->rx_dma;
 648         drv_data->tx_dma = transfer->tx_dma;
 649         drv_data->len_in_bytes = transfer->len;
 650         drv_data->cs_change = transfer->cs_change;
 651
 652         /* Bits per word setup */
 653         bits_per_word = transfer->bits_per_word ? : message->spi->bits_per_word;
 654         if (bits_per_word == 8) {
 655                 drv_data->n_bytes = 1;
 656                 drv_data->len = transfer->len;
 657                 cr_width = 0;
 658                 drv_data->ops = &bfin_bfin_spi_transfer_ops_u8;
 659         } else if (bits_per_word == 16) {
 660                 drv_data->n_bytes = 2;
 661                 drv_data->len = (transfer->len) >> 1;
 662                 cr_width = BIT_CTL_WORDSIZE;
 663                 drv_data->ops = &bfin_bfin_spi_transfer_ops_u16;
 664         } else {
 665                 dev_err(&drv_data->pdev->dev, "transfer: unsupported bits_per_word\n");
 666                 message->status = -EINVAL;
 667                 bfin_spi_giveback(drv_data);
 668                 return;
 669         }
 670         cr = read_CTRL(drv_data) & ~(BIT_CTL_TIMOD | BIT_CTL_WORDSIZE);
 671         cr |= cr_width;
 672         write_CTRL(drv_data, cr);
 673
 674         dev_dbg(&drv_data->pdev->dev,
 675                 "transfer: drv_data->ops is %p, chip->ops is %p, u8_ops is %p\n",
 676                 drv_data->ops, chip->ops, &bfin_bfin_spi_transfer_ops_u8);
 677
 678         message->state = RUNNING_STATE;
 679         dma_config = 0;
 680
 681         /* Speed setup (surely valid because already checked) */
 682         if (transfer->speed_hz)
 683                 write_BAUD(drv_data, hz_to_spi_baud(transfer->speed_hz));
 684         else
 685                 write_BAUD(drv_data, chip->baud);
 686
 687         write_STAT(drv_data, BIT_STAT_CLR);
 688         bfin_spi_cs_active(drv_data, chip);
 689
 690         dev_dbg(&drv_data->pdev->dev,
 691                 "now pumping a transfer: width is %d, len is %d\n",
 692                 cr_width, transfer->len);
 693
 694         /*
 695          * Try to map dma buffer and do a dma transfer.  If successful use,
 696          * different way to r/w according to the enable_dma settings and if
 697          * we are not doing a full duplex transfer (since the hardware does
 698          * not support full duplex DMA transfers).
 699          */
 700         if (!full_duplex && drv_data->cur_chip->enable_dma
 701                                 && drv_data->len > 6) {
 702
 703                 unsigned long dma_start_addr, flags;
 704
 705                 disable_dma(drv_data->dma_channel);
 706                 clear_dma_irqstat(drv_data->dma_channel);
 707
 708                 /* config dma channel */
 709                 dev_dbg(&drv_data->pdev->dev, "doing dma transfer\n");
 710                 set_dma_x_count(drv_data->dma_channel, drv_data->len);
 711                 if (cr_width == BIT_CTL_WORDSIZE) {
 712                         set_dma_x_modify(drv_data->dma_channel, 2);
 713                         dma_width = WDSIZE_16;
 714                 } else {
 715                         set_dma_x_modify(drv_data->dma_channel, 1);
 716                         dma_width = WDSIZE_8;
 717                 }
 718
 719                 /* poll for SPI completion before start */
 720                 while (!(read_STAT(drv_data) & BIT_STAT_SPIF))
 721                         cpu_relax();
 722
 723                 /* dirty hack for autobuffer DMA mode */
 724                 if (drv_data->tx_dma == 0xFFFF) {
 725                         dev_dbg(&drv_data->pdev->dev,
 726                                 "doing autobuffer DMA out.\n");
 727
 728                         /* no irq in autobuffer mode */
 729                         dma_config =
 730                             (DMAFLOW_AUTO | RESTART | dma_width | DI_EN);
 731                         set_dma_config(drv_data->dma_channel, dma_config);
 732                         set_dma_start_addr(drv_data->dma_channel,
 733                                         (unsigned long)drv_data->tx);
 734                         enable_dma(drv_data->dma_channel);
 735
 736                         /* start SPI transfer */
 737                         write_CTRL(drv_data, cr | BIT_CTL_TIMOD_DMA_TX);
 738
 739                         /* just return here, there can only be one transfer
 740                          * in this mode
 741                          */
 742                         message->status = 0;
 743                         bfin_spi_giveback(drv_data);
 744                         return;
 745                 }
 746
 747                 /* In dma mode, rx or tx must be NULL in one transfer */
 748                 dma_config = (RESTART | dma_width | DI_EN);
 749                 if (drv_data->rx != NULL) {
 750                         /* set transfer mode, and enable SPI */
 751                         dev_dbg(&drv_data->pdev->dev, "doing DMA in to %p (size %zx)\n",
 752                                 drv_data->rx, drv_data->len_in_bytes);
 753
 754                         /* invalidate caches, if needed */
 755                         if (bfin_addr_dcacheable((unsigned long) drv_data->rx))
 756                                 invalidate_dcache_range((unsigned long) drv_data->rx,
 757                                                         (unsigned long) (drv_data->rx +
 758                                                         drv_data->len_in_bytes));
 759
 760                         dma_config |= WNR;
 761                         dma_start_addr = (unsigned long)drv_data->rx;
 762                         cr |= BIT_CTL_TIMOD_DMA_RX | BIT_CTL_SENDOPT;
 763
 764                 } else if (drv_data->tx != NULL) {
 765                         dev_dbg(&drv_data->pdev->dev, "doing DMA out.\n");
 766
 767                         /* flush caches, if needed */
 768                         if (bfin_addr_dcacheable((unsigned long) drv_data->tx))
 769                                 flush_dcache_range((unsigned long) drv_data->tx,
 770                                                 (unsigned long) (drv_data->tx +
 771                                                 drv_data->len_in_bytes));
 772
 773                         dma_start_addr = (unsigned long)drv_data->tx;
 774                         cr |= BIT_CTL_TIMOD_DMA_TX;
 775
 776                 } else
 777                         BUG();
 778
 779                 /* oh man, here there be monsters ... and i dont mean the
 780                  * fluffy cute ones from pixar, i mean the kind that'll eat
 781                  * your data, kick your dog, and love it all.  do *not* try
 782                  * and change these lines unless you (1) heavily test DMA
 783                  * with SPI flashes on a loaded system (e.g. ping floods),
 784                  * (2) know just how broken the DMA engine interaction with
 785                  * the SPI peripheral is, and (3) have someone else to blame
 786                  * when you screw it all up anyways.
 787                  */
 788                 set_dma_start_addr(drv_data->dma_channel, dma_start_addr);
 789                 set_dma_config(drv_data->dma_channel, dma_config);
 790                 local_irq_save(flags);
 791                 SSYNC();
 792                 write_CTRL(drv_data, cr);
 793                 enable_dma(drv_data->dma_channel);
 794                 dma_enable_irq(drv_data->dma_channel);
 795                 local_irq_restore(flags);
 796
 797                 return;
 798         }
 799
 800         /*
 801          * We always use SPI_WRITE mode (transfer starts with TDBR write).
 802          * SPI_READ mode (transfer starts with RDBR read) seems to have
 803          * problems with setting up the output value in TDBR prior to the
 804          * start of the transfer.
 805          */
 806         write_CTRL(drv_data, cr | BIT_CTL_TXMOD);
 807
 808         if (chip->pio_interrupt) {
 809                 /* SPI irq should have been disabled by now */
 810
 811                 /* discard old RX data and clear RXS */
 812                 bfin_spi_dummy_read(drv_data);
 813
 814                 /* start transfer */
 815                 if (drv_data->tx == NULL)
 816                         write_TDBR(drv_data, chip->idle_tx_val);
 817                 else {
 818                         if (bits_per_word == 8)
 819                                 write_TDBR(drv_data, (*(u8 *) (drv_data->tx)));
 820                         else
 821                                 write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
 822                         drv_data->tx += drv_data->n_bytes;
 823                 }
 824
 825                 /* once TDBR is empty, interrupt is triggered */
 826                 enable_irq(drv_data->spi_irq);
 827                 return;
 828         }
 829
 830         /* IO mode */
 831         dev_dbg(&drv_data->pdev->dev, "doing IO transfer\n");
 832
 833         if (full_duplex) {
 834                 /* full duplex mode */
 835                 BUG_ON((drv_data->tx_end - drv_data->tx) !=
 836                        (drv_data->rx_end - drv_data->rx));
 837                 dev_dbg(&drv_data->pdev->dev,
 838                         "IO duplex: cr is 0x%x\n", cr);
 839
 840                 drv_data->ops->duplex(drv_data);
 841
 842                 if (drv_data->tx != drv_data->tx_end)
 843                         tranf_success = 0;
 844         } else if (drv_data->tx != NULL) {
 845                 /* write only half duplex */
 846                 dev_dbg(&drv_data->pdev->dev,
 847                         "IO write: cr is 0x%x\n", cr);
 848
 849                 drv_data->ops->write(drv_data);
 850
 851                 if (drv_data->tx != drv_data->tx_end)
 852                         tranf_success = 0;
 853         } else if (drv_data->rx != NULL) {
 854                 /* read only half duplex */
 855                 dev_dbg(&drv_data->pdev->dev,
 856                         "IO read: cr is 0x%x\n", cr);
 857
 858                 drv_data->ops->read(drv_data);
 859                 if (drv_data->rx != drv_data->rx_end)
 860                         tranf_success = 0;
 861         }
 862
 863         if (!tranf_success) {
 864                 dev_dbg(&drv_data->pdev->dev,
 865                         "IO write error!\n");
 866                 message->state = ERROR_STATE;
 867         } else {
 868                 /* Update total byte transfered */
 869                 message->actual_length += drv_data->len_in_bytes;
 870                 /* Move to next transfer of this msg */
 871                 message->state = bfin_spi_next_transfer(drv_data);
 872                 if (drv_data->cs_change)
 873                         bfin_spi_cs_deactive(drv_data, chip);
 874         }
 875
 876         /* Schedule next transfer tasklet */
 877         tasklet_schedule(&drv_data->pump_transfers);
 878 }
 879
 880 /* pop a msg from queue and kick off real transfer */
 881 static void bfin_spi_pump_messages(struct work_struct *work)
 882 {
 883         struct bfin_spi_master_data *drv_data;
 884         unsigned long flags;
 885
 886         drv_data = container_of(work, struct bfin_spi_master_data, pump_messages);
 887
 888         /* Lock queue and check for queue work */
 889         spin_lock_irqsave(&drv_data->lock, flags);
 890         if (list_empty(&drv_data->queue) || !drv_data->running) {
 891                 /* pumper kicked off but no work to do */
 892                 drv_data->busy = 0;
 893                 spin_unlock_irqrestore(&drv_data->lock, flags);
 894                 return;
 895         }
 896
 897         /* Make sure we are not already running a message */
 898         if (drv_data->cur_msg) {
 899                 spin_unlock_irqrestore(&drv_data->lock, flags);
 900                 return;
 901         }
 902
 903         /* Extract head of queue */
 904         drv_data->cur_msg = list_entry(drv_data->queue.next,
 905                                        struct spi_message, queue);
 906
 907         /* Setup the SSP using the per chip configuration */
 908         drv_data->cur_chip = spi_get_ctldata(drv_data->cur_msg->spi);
 909         bfin_spi_restore_state(drv_data);
 910
 911         list_del_init(&drv_data->cur_msg->queue);
 912
 913         /* Initial message state */
 914         drv_data->cur_msg->state = START_STATE;
 915         drv_data->cur_transfer = list_entry(drv_data->cur_msg->transfers.next,
 916                                             struct spi_transfer, transfer_list);
 917
 918         dev_dbg(&drv_data->pdev->dev, "got a message to pump, "
 919                 "state is set to: baud %d, flag 0x%x, ctl 0x%x\n",
 920                 drv_data->cur_chip->baud, drv_data->cur_chip->flag,
 921                 drv_data->cur_chip->ctl_reg);
 922
 923         dev_dbg(&drv_data->pdev->dev,
 924                 "the first transfer len is %d\n",
 925                 drv_data->cur_transfer->len);
 926
 927         /* Mark as busy and launch transfers */
 928         tasklet_schedule(&drv_data->pump_transfers);
 929
 930         drv_data->busy = 1;
 931         spin_unlock_irqrestore(&drv_data->lock, flags);
 932 }
 933
 934 /*
 935  * got a msg to transfer, queue it in drv_data->queue.
 936  * And kick off message pumper
 937  */
 938 static int bfin_spi_transfer(struct spi_device *spi, struct spi_message *msg)
 939 {
 940         struct bfin_spi_master_data *drv_data = spi_master_get_devdata(spi->master);
 941         unsigned long flags;
 942
 943         spin_lock_irqsave(&drv_data->lock, flags);
 944
 945         if (!drv_data->running) {
 946                 spin_unlock_irqrestore(&drv_data->lock, flags);
 947                 return -ESHUTDOWN;
 948         }
 949
 950         msg->actual_length = 0;
 951         msg->status = -EINPROGRESS;
 952         msg->state = START_STATE;
 953
 954         dev_dbg(&spi->dev, "adding an msg in transfer() \n");
 955         list_add_tail(&msg->queue, &drv_data->queue);
 956
 957         if (drv_data->running && !drv_data->busy)
 958                 queue_work(drv_data->workqueue, &drv_data->pump_messages);
 959
 960         spin_unlock_irqrestore(&drv_data->lock, flags);
 961
 962         return 0;
 963 }
 964
 965 #define MAX_SPI_SSEL    7
 966
 967 static u16 ssel[][MAX_SPI_SSEL] = {
 968         {P_SPI0_SSEL1, P_SPI0_SSEL2, P_SPI0_SSEL3,
 969         P_SPI0_SSEL4, P_SPI0_SSEL5,
 970         P_SPI0_SSEL6, P_SPI0_SSEL7},
 971
 972         {P_SPI1_SSEL1, P_SPI1_SSEL2, P_SPI1_SSEL3,
 973         P_SPI1_SSEL4, P_SPI1_SSEL5,
 974         P_SPI1_SSEL6, P_SPI1_SSEL7},
 975
 976         {P_SPI2_SSEL1, P_SPI2_SSEL2, P_SPI2_SSEL3,
 977         P_SPI2_SSEL4, P_SPI2_SSEL5,
 978         P_SPI2_SSEL6, P_SPI2_SSEL7},
 979 };
 980
 981 /* setup for devices (may be called multiple times -- not just first setup) */
 982 static int bfin_spi_setup(struct spi_device *spi)
 983 {
 984         struct bfin5xx_spi_chip *chip_info;
 985         struct bfin_spi_slave_data *chip = NULL;
 986         struct bfin_spi_master_data *drv_data = spi_master_get_devdata(spi->master);
 987         u16 bfin_ctl_reg;
 988         int ret = -EINVAL;
 989
 990         /* Only alloc (or use chip_info) on first setup */
 991         chip_info = NULL;
 992         chip = spi_get_ctldata(spi);
 993         if (chip == NULL) {
 994                 chip = kzalloc(sizeof(*chip), GFP_KERNEL);
 995                 if (!chip) {
 996                         dev_err(&spi->dev, "cannot allocate chip data\n");
 997                         ret = -ENOMEM;
 998                         goto error;
 999                 }
1000
1001                 chip->enable_dma = 0;
1002                 chip_info = spi->controller_data;
1003         }
1004
1005         /* Let people set non-standard bits directly */
1006         bfin_ctl_reg = BIT_CTL_OPENDRAIN | BIT_CTL_EMISO |
1007                 BIT_CTL_PSSE | BIT_CTL_GM | BIT_CTL_SZ;
1008
1009         /* chip_info isn't always needed */
1010         if (chip_info) {
1011                 /* Make sure people stop trying to set fields via ctl_reg
1012                  * when they should actually be using common SPI framework.
1013                  * Currently we let through: WOM EMISO PSSE GM SZ.
1014                  * Not sure if a user actually needs/uses any of these,
1015                  * but let's assume (for now) they do.
1016                  */
1017                 if (chip_info->ctl_reg & ~bfin_ctl_reg) {
1018                         dev_err(&spi->dev, "do not set bits in ctl_reg "
1019                                 "that the SPI framework manages\n");
1020                         goto error;
1021                 }
1022                 chip->enable_dma = chip_info->enable_dma != 0
1023                     && drv_data->master_info->enable_dma;
1024                 chip->ctl_reg = chip_info->ctl_reg;
1025                 chip->cs_chg_udelay = chip_info->cs_chg_udelay;
1026                 chip->idle_tx_val = chip_info->idle_tx_val;
1027                 chip->pio_interrupt = chip_info->pio_interrupt;
1028                 spi->bits_per_word = chip_info->bits_per_word;
1029         } else {
1030                 /* force a default base state */
1031                 chip->ctl_reg &= bfin_ctl_reg;
1032         }
1033
1034         if (spi->bits_per_word != 8 && spi->bits_per_word != 16) {
1035                 dev_err(&spi->dev, "%d bits_per_word is not supported\n",
1036                                 spi->bits_per_word);
1037                 goto error;
1038         }
1039
1040         /* translate common spi framework into our register */
1041         if (spi->mode & ~(SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST)) {
1042                 dev_err(&spi->dev, "unsupported spi modes detected\n");
1043                 goto error;
1044         }
1045         if (spi->mode & SPI_CPOL)
1046                 chip->ctl_reg |= BIT_CTL_CPOL;
1047         if (spi->mode & SPI_CPHA)
1048                 chip->ctl_reg |= BIT_CTL_CPHA;
1049         if (spi->mode & SPI_LSB_FIRST)
1050                 chip->ctl_reg |= BIT_CTL_LSBF;
1051         /* we dont support running in slave mode (yet?) */
1052         chip->ctl_reg |= BIT_CTL_MASTER;
1053
1054         /*
1055          * Notice: for blackfin, the speed_hz is the value of register
1056          * SPI_BAUD, not the real baudrate
1057          */
1058         chip->baud = hz_to_spi_baud(spi->max_speed_hz);
1059         chip->chip_select_num = spi->chip_select;
1060         if (chip->chip_select_num < MAX_CTRL_CS) {
1061                 if (!(spi->mode & SPI_CPHA))
1062                         dev_warn(&spi->dev, "Warning: SPI CPHA not set:"
1063                                 " Slave Select not under software control!\n"
1064                                 " See Documentation/blackfin/bfin-spi-notes.txt");
1065
1066                 chip->flag = (1 << spi->chip_select) << 8;
1067         } else
1068                 chip->cs_gpio = chip->chip_select_num - MAX_CTRL_CS;
1069
1070         if (chip->enable_dma && chip->pio_interrupt) {
1071                 dev_err(&spi->dev, "enable_dma is set, "
1072                                 "do not set pio_interrupt\n");
1073                 goto error;
1074         }
1075         /*
1076          * if any one SPI chip is registered and wants DMA, request the
1077          * DMA channel for it
1078          */
1079         if (chip->enable_dma && !drv_data->dma_requested) {
1080                 /* register dma irq handler */
1081                 ret = request_dma(drv_data->dma_channel, "BFIN_SPI_DMA");
1082                 if (ret) {
1083                         dev_err(&spi->dev,
1084                                 "Unable to request BlackFin SPI DMA channel\n");
1085                         goto error;
1086                 }
1087                 drv_data->dma_requested = 1;
1088
1089                 ret = set_dma_callback(drv_data->dma_channel,
1090                         bfin_spi_dma_irq_handler, drv_data);
1091                 if (ret) {
1092                         dev_err(&spi->dev, "Unable to set dma callback\n");
1093                         goto error;
1094                 }
1095                 dma_disable_irq(drv_data->dma_channel);
1096         }
1097
1098         if (chip->pio_interrupt && !drv_data->irq_requested) {
1099                 ret = request_irq(drv_data->spi_irq, bfin_spi_pio_irq_handler,
1100                         IRQF_DISABLED, "BFIN_SPI", drv_data);
1101                 if (ret) {
1102                         dev_err(&spi->dev, "Unable to register spi IRQ\n");
1103                         goto error;
1104                 }
1105                 drv_data->irq_requested = 1;
1106                 /* we use write mode, spi irq has to be disabled here */
1107                 disable_irq(drv_data->spi_irq);
1108         }
1109
1110         if (chip->chip_select_num >= MAX_CTRL_CS) {
1111                 /* Only request on first setup */
1112                 if (spi_get_ctldata(spi) == NULL) {
1113                         ret = gpio_request(chip->cs_gpio, spi->modalias);
1114                         if (ret) {
1115                                 dev_err(&spi->dev, "gpio_request() error\n");
1116                                 goto pin_error;
1117                         }
1118                         gpio_direction_output(chip->cs_gpio, 1);
1119                 }
1120         }
1121
1122         dev_dbg(&spi->dev, "setup spi chip %s, width is %d, dma is %d\n",
1123                         spi->modalias, spi->bits_per_word, chip->enable_dma);
1124         dev_dbg(&spi->dev, "ctl_reg is 0x%x, flag_reg is 0x%x\n",
1125                         chip->ctl_reg, chip->flag);
1126
1127         spi_set_ctldata(spi, chip);
1128
1129         dev_dbg(&spi->dev, "chip select number is %d\n", chip->chip_select_num);
1130         if (chip->chip_select_num < MAX_CTRL_CS) {
1131                 ret = peripheral_request(ssel[spi->master->bus_num]
1132                                          [chip->chip_select_num-1], spi->modalias);
1133                 if (ret) {
1134                         dev_err(&spi->dev, "peripheral_request() error\n");
1135                         goto pin_error;
1136                 }
1137         }
1138
1139         bfin_spi_cs_enable(drv_data, chip);
1140         bfin_spi_cs_deactive(drv_data, chip);
1141
1142         return 0;
1143
1144  pin_error:
1145         if (chip->chip_select_num >= MAX_CTRL_CS)
1146                 gpio_free(chip->cs_gpio);
1147         else
1148                 peripheral_free(ssel[spi->master->bus_num]
1149                         [chip->chip_select_num - 1]);
1150  error:
1151         if (chip) {
1152                 if (drv_data->dma_requested)
1153                         free_dma(drv_data->dma_channel);
1154                 drv_data->dma_requested = 0;
1155
1156                 kfree(chip);
1157                 /* prevent free 'chip' twice */
1158                 spi_set_ctldata(spi, NULL);
1159         }
1160
1161         return ret;
1162 }
1163
1164 /*
1165  * callback for spi framework.
1166  * clean driver specific data
1167  */
1168 static void bfin_spi_cleanup(struct spi_device *spi)
1169 {
1170         struct bfin_spi_slave_data *chip = spi_get_ctldata(spi);
1171         struct bfin_spi_master_data *drv_data = spi_master_get_devdata(spi->master);
1172
1173         if (!chip)
1174                 return;
1175
1176         if (chip->chip_select_num < MAX_CTRL_CS) {
1177                 peripheral_free(ssel[spi->master->bus_num]
1178                                         [chip->chip_select_num-1]);
1179                 bfin_spi_cs_disable(drv_data, chip);
1180         } else
1181                 gpio_free(chip->cs_gpio);
1182
1183         kfree(chip);
1184         /* prevent free 'chip' twice */
1185         spi_set_ctldata(spi, NULL);
1186 }
1187
1188 static inline int bfin_spi_init_queue(struct bfin_spi_master_data *drv_data)
1189 {
1190         INIT_LIST_HEAD(&drv_data->queue);
1191         spin_lock_init(&drv_data->lock);
1192
1193         drv_data->running = false;
1194         drv_data->busy = 0;
1195
1196         /* init transfer tasklet */
1197         tasklet_init(&drv_data->pump_transfers,
1198                      bfin_spi_pump_transfers, (unsigned long)drv_data);
1199
1200         /* init messages workqueue */
1201         INIT_WORK(&drv_data->pump_messages, bfin_spi_pump_messages);
1202         drv_data->workqueue = create_singlethread_workqueue(
1203                                 dev_name(drv_data->master->dev.parent));
1204         if (drv_data->workqueue == NULL)
1205                 return -EBUSY;
1206
1207         return 0;
1208 }
1209
1210 static inline int bfin_spi_start_queue(struct bfin_spi_master_data *drv_data)
1211 {
1212         unsigned long flags;
1213
1214         spin_lock_irqsave(&drv_data->lock, flags);
1215
1216         if (drv_data->running || drv_data->busy) {
1217                 spin_unlock_irqrestore(&drv_data->lock, flags);
1218                 return -EBUSY;
1219         }
1220
1221         drv_data->running = true;
1222         drv_data->cur_msg = NULL;
1223         drv_data->cur_transfer = NULL;
1224         drv_data->cur_chip = NULL;
1225         spin_unlock_irqrestore(&drv_data->lock, flags);
1226
1227         queue_work(drv_data->workqueue, &drv_data->pump_messages);
1228
1229         return 0;
1230 }
1231
1232 static inline int bfin_spi_stop_queue(struct bfin_spi_master_data *drv_data)
1233 {
1234         unsigned long flags;
1235         unsigned limit = 500;
1236         int status = 0;
1237
1238         spin_lock_irqsave(&drv_data->lock, flags);
1239
1240         /*
1241          * This is a bit lame, but is optimized for the common execution path.
1242          * A wait_queue on the drv_data->busy could be used, but then the common
1243          * execution path (pump_messages) would be required to call wake_up or
1244          * friends on every SPI message. Do this instead
1245          */
1246         drv_data->running = false;
1247         while (!list_empty(&drv_data->queue) && drv_data->busy && limit--) {
1248                 spin_unlock_irqrestore(&drv_data->lock, flags);
1249                 msleep(10);
1250                 spin_lock_irqsave(&drv_data->lock, flags);
1251         }
1252
1253         if (!list_empty(&drv_data->queue) || drv_data->busy)
1254                 status = -EBUSY;
1255
1256         spin_unlock_irqrestore(&drv_data->lock, flags);
1257
1258         return status;
1259 }
1260
1261 static inline int bfin_spi_destroy_queue(struct bfin_spi_master_data *drv_data)
1262 {
1263         int status;
1264
1265         status = bfin_spi_stop_queue(drv_data);
1266         if (status != 0)
1267                 return status;
1268
1269         destroy_workqueue(drv_data->workqueue);
1270
1271         return 0;
1272 }
1273
1274 static int __init bfin_spi_probe(struct platform_device *pdev)
1275 {
1276         struct device *dev = &pdev->dev;
1277         struct bfin5xx_spi_master *platform_info;
1278         struct spi_master *master;
1279         struct bfin_spi_master_data *drv_data;
1280         struct resource *res;
1281         int status = 0;
1282
1283         platform_info = dev->platform_data;
1284
1285         /* Allocate master with space for drv_data */
1286         master = spi_alloc_master(dev, sizeof(*drv_data));
1287         if (!master) {
1288                 dev_err(&pdev->dev, "can not alloc spi_master\n");
1289                 return -ENOMEM;
1290         }
1291
1292         drv_data = spi_master_get_devdata(master);
1293         drv_data->master = master;
1294         drv_data->master_info = platform_info;
1295         drv_data->pdev = pdev;
1296         drv_data->pin_req = platform_info->pin_req;
1297
1298         /* the spi->mode bits supported by this driver: */
1299         master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST;
1300
1301         master->bus_num = pdev->id;
1302         master->num_chipselect = platform_info->num_chipselect;
1303         master->cleanup = bfin_spi_cleanup;
1304         master->setup = bfin_spi_setup;
1305         master->transfer = bfin_spi_transfer;
1306
1307         /* Find and map our resources */
1308         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1309         if (res == NULL) {
1310                 dev_err(dev, "Cannot get IORESOURCE_MEM\n");
1311                 status = -ENOENT;
1312                 goto out_error_get_res;
1313         }
1314
1315         drv_data->regs_base = ioremap(res->start, resource_size(res));
1316         if (drv_data->regs_base == NULL) {
1317                 dev_err(dev, "Cannot map IO\n");
1318                 status = -ENXIO;
1319                 goto out_error_ioremap;
1320         }
1321
1322         res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
1323         if (res == NULL) {
1324                 dev_err(dev, "No DMA channel specified\n");
1325                 status = -ENOENT;
1326                 goto out_error_free_io;
1327         }
1328         drv_data->dma_channel = res->start;
1329
1330         drv_data->spi_irq = platform_get_irq(pdev, 0);
1331         if (drv_data->spi_irq < 0) {
1332                 dev_err(dev, "No spi pio irq specified\n");
1333                 status = -ENOENT;
1334                 goto out_error_free_io;
1335         }
1336
1337         /* Initial and start queue */
1338         status = bfin_spi_init_queue(drv_data);
1339         if (status != 0) {
1340                 dev_err(dev, "problem initializing queue\n");
1341                 goto out_error_queue_alloc;
1342         }
1343
1344         status = bfin_spi_start_queue(drv_data);
1345         if (status != 0) {
1346                 dev_err(dev, "problem starting queue\n");
1347                 goto out_error_queue_alloc;
1348         }
1349
1350         status = peripheral_request_list(drv_data->pin_req, DRV_NAME);
1351         if (status != 0) {
1352                 dev_err(&pdev->dev, ": Requesting Peripherals failed\n");
1353                 goto out_error_queue_alloc;
1354         }
1355
1356         /* Reset SPI registers. If these registers were used by the boot loader,
1357          * the sky may fall on your head if you enable the dma controller.
1358          */
1359         write_CTRL(drv_data, BIT_CTL_CPHA | BIT_CTL_MASTER);
1360         write_FLAG(drv_data, 0xFF00);
1361
1362         /* Register with the SPI framework */
1363         platform_set_drvdata(pdev, drv_data);
1364         status = spi_register_master(master);
1365         if (status != 0) {
1366                 dev_err(dev, "problem registering spi master\n");
1367                 goto out_error_queue_alloc;
1368         }
1369
1370         dev_info(dev, "%s, Version %s, regs_base@%p, dma channel@%d\n",
1371                 DRV_DESC, DRV_VERSION, drv_data->regs_base,
1372                 drv_data->dma_channel);
1373         return status;
1374
1375 out_error_queue_alloc:
1376         bfin_spi_destroy_queue(drv_data);
1377 out_error_free_io:
1378         iounmap((void *) drv_data->regs_base);
1379 out_error_ioremap:
1380 out_error_get_res:
1381         spi_master_put(master);
1382
1383         return status;
1384 }
1385
1386 /* stop hardware and remove the driver */
1387 static int __devexit bfin_spi_remove(struct platform_device *pdev)
1388 {
1389         struct bfin_spi_master_data *drv_data = platform_get_drvdata(pdev);
1390         int status = 0;
1391
1392         if (!drv_data)
1393                 return 0;
1394
1395         /* Remove the queue */
1396         status = bfin_spi_destroy_queue(drv_data);
1397         if (status != 0)
1398                 return status;
1399
1400         /* Disable the SSP at the peripheral and SOC level */
1401         bfin_spi_disable(drv_data);
1402
1403         /* Release DMA */
1404         if (drv_data->master_info->enable_dma) {
1405                 if (dma_channel_active(drv_data->dma_channel))
1406                         free_dma(drv_data->dma_channel);
1407         }
1408
1409         if (drv_data->irq_requested) {
1410                 free_irq(drv_data->spi_irq, drv_data);
1411                 drv_data->irq_requested = 0;
1412         }
1413
1414         /* Disconnect from the SPI framework */
1415         spi_unregister_master(drv_data->master);
1416
1417         peripheral_free_list(drv_data->pin_req);
1418
1419         /* Prevent double remove */
1420         platform_set_drvdata(pdev, NULL);
1421
1422         return 0;
1423 }
1424
1425 #ifdef CONFIG_PM
1426 static int bfin_spi_suspend(struct platform_device *pdev, pm_message_t state)
1427 {
1428         struct bfin_spi_master_data *drv_data = platform_get_drvdata(pdev);
1429         int status = 0;
1430
1431         status = bfin_spi_stop_queue(drv_data);
1432         if (status != 0)
1433                 return status;
1434
1435         drv_data->ctrl_reg = read_CTRL(drv_data);
1436         drv_data->flag_reg = read_FLAG(drv_data);
1437
1438         /*
1439          * reset SPI_CTL and SPI_FLG registers
1440          */
1441         write_CTRL(drv_data, BIT_CTL_CPHA | BIT_CTL_MASTER);
1442         write_FLAG(drv_data, 0xFF00);
1443
1444         return 0;
1445 }
1446
1447 static int bfin_spi_resume(struct platform_device *pdev)
1448 {
1449         struct bfin_spi_master_data *drv_data = platform_get_drvdata(pdev);
1450         int status = 0;
1451
1452         write_CTRL(drv_data, drv_data->ctrl_reg);
1453         write_FLAG(drv_data, drv_data->flag_reg);
1454
1455         /* Start the queue running */
1456         status = bfin_spi_start_queue(drv_data);
1457         if (status != 0) {
1458                 dev_err(&pdev->dev, "problem starting queue (%d)\n", status);
1459                 return status;
1460         }
1461
1462         return 0;
1463 }
1464 #else
1465 #define bfin_spi_suspend NULL
1466 #define bfin_spi_resume NULL
1467 #endif                          /* CONFIG_PM */
1468
1469 MODULE_ALIAS("platform:bfin-spi");
1470 static struct platform_driver bfin_spi_driver = {
1471         .driver = {
1472                 .name   = DRV_NAME,
1473                 .owner  = THIS_MODULE,
1474         },
1475         .suspend        = bfin_spi_suspend,
1476         .resume         = bfin_spi_resume,
1477         .remove         = __devexit_p(bfin_spi_remove),
1478 };
1479
1480 static int __init bfin_spi_init(void)
1481 {
1482         return platform_driver_probe(&bfin_spi_driver, bfin_spi_probe);
1483 }
1484 subsys_initcall(bfin_spi_init);
1485
1486 static void __exit bfin_spi_exit(void)
1487 {
1488         platform_driver_unregister(&bfin_spi_driver);
1489 }
1490 module_exit(bfin_spi_exit);