drivers/net/wireless/orinoco/orinoco_usb.c

   1 /*
   2  * USB Orinoco driver
   3  *
   4  * Copyright (c) 2003 Manuel Estrada Sainz
   5  *
   6  * The contents of this file are subject to the Mozilla Public License
   7  * Version 1.1 (the "License"); you may not use this file except in
   8  * compliance with the License. You may obtain a copy of the License
   9  * at http://www.mozilla.org/MPL/
  10  *
  11  * Software distributed under the License is distributed on an "AS IS"
  12  * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
  13  * the License for the specific language governing rights and
  14  * limitations under the License.
  15  *
  16  * Alternatively, the contents of this file may be used under the
  17  * terms of the GNU General Public License version 2 (the "GPL"), in
  18  * which case the provisions of the GPL are applicable instead of the
  19  * above.  If you wish to allow the use of your version of this file
  20  * only under the terms of the GPL and not to allow others to use your
  21  * version of this file under the MPL, indicate your decision by
  22  * deleting the provisions above and replace them with the notice and
  23  * other provisions required by the GPL.  If you do not delete the
  24  * provisions above, a recipient may use your version of this file
  25  * under either the MPL or the GPL.
  26  *
  27  * Queueing code based on linux-wlan-ng 0.2.1-pre5
  28  *
  29  * Copyright (C) 1999 AbsoluteValue Systems, Inc.  All Rights Reserved.
  30  *
  31  *      The license is the same as above.
  32  *
  33  * Initialy based on USB Skeleton driver - 0.7
  34  *
  35  * Copyright (c) 2001 Greg Kroah-Hartman (greg@kroah.com)
  36  *
  37  *      This program is free software; you can redistribute it and/or
  38  *      modify it under the terms of the GNU General Public License as
  39  *      published by the Free Software Foundation; either version 2 of
  40  *      the License, or (at your option) any later version.
  41  *
  42  * NOTE: The original USB Skeleton driver is GPL, but all that code is
  43  * gone so MPL/GPL applies.
  44  */
  45
  46 #define DRIVER_NAME "orinoco_usb"
  47 #define PFX DRIVER_NAME ": "
  48
  49 #include <linux/module.h>
  50 #include <linux/kernel.h>
  51 #include <linux/sched.h>
  52 #include <linux/signal.h>
  53 #include <linux/errno.h>
  54 #include <linux/poll.h>
  55 #include <linux/init.h>
  56 #include <linux/slab.h>
  57 #include <linux/fcntl.h>
  58 #include <linux/spinlock.h>
  59 #include <linux/list.h>
  60 #include <linux/usb.h>
  61 #include <linux/timer.h>
  62
  63 #include <linux/netdevice.h>
  64 #include <linux/if_arp.h>
  65 #include <linux/etherdevice.h>
  66 #include <linux/wireless.h>
  67 #include <linux/firmware.h>
  68
  69 #include "mic.h"
  70 #include "orinoco.h"
  71
  72 #ifndef URB_ASYNC_UNLINK
  73 #define URB_ASYNC_UNLINK 0
  74 #endif
  75
  76 /* 802.2 LLC/SNAP header used for Ethernet encapsulation over 802.11 */
  77 static const u8 encaps_hdr[] = {0xaa, 0xaa, 0x03, 0x00, 0x00, 0x00};
  78 #define ENCAPS_OVERHEAD         (sizeof(encaps_hdr) + 2)
  79
  80 struct header_struct {
  81         /* 802.3 */
  82         u8 dest[ETH_ALEN];
  83         u8 src[ETH_ALEN];
  84         __be16 len;
  85         /* 802.2 */
  86         u8 dsap;
  87         u8 ssap;
  88         u8 ctrl;
  89         /* SNAP */
  90         u8 oui[3];
  91         __be16 ethertype;
  92 } __packed;
  93
  94 struct ez_usb_fw {
  95         u16 size;
  96         const u8 *code;
  97 };
  98
  99 static struct ez_usb_fw firmware = {
 100         .size = 0,
 101         .code = NULL,
 102 };
 103
 104 #ifdef CONFIG_USB_DEBUG
 105 static int debug = 1;
 106 #else
 107 static int debug;
 108 #endif
 109
 110 /* Debugging macros */
 111 #undef dbg
 112 #define dbg(format, arg...) \
 113         do { if (debug) printk(KERN_DEBUG PFX "%s: " format "\n", \
 114                                __func__ , ## arg); } while (0)
 115 #undef err
 116 #define err(format, arg...) \
 117         do { printk(KERN_ERR PFX format "\n", ## arg); } while (0)
 118
 119 /* Module paramaters */
 120 module_param(debug, int, 0644);
 121 MODULE_PARM_DESC(debug, "Debug enabled or not");
 122
 123 MODULE_FIRMWARE("orinoco_ezusb_fw");
 124
 125 /*
 126  * Under some conditions, the card gets stuck and stops paying attention
 127  * to the world (i.e. data communication stalls) until we do something to
 128  * it.  Sending an INQ_TALLIES command seems to be enough and should be
 129  * harmless otherwise.  This behaviour has been observed when using the
 130  * driver on a systemimager client during installation.  In the past a
 131  * timer was used to send INQ_TALLIES commands when there was no other
 132  * activity, but it was troublesome and was removed.
 133  */
 134
 135 #define USB_COMPAQ_VENDOR_ID     0x049f /* Compaq Computer Corp. */
 136 #define USB_COMPAQ_WL215_ID      0x001f /* Compaq WL215 USB Adapter */
 137 #define USB_COMPAQ_W200_ID       0x0076 /* Compaq W200 USB Adapter */
 138 #define USB_HP_WL215_ID          0x0082 /* Compaq WL215 USB Adapter */
 139
 140 #define USB_MELCO_VENDOR_ID      0x0411
 141 #define USB_BUFFALO_L11_ID       0x0006 /* BUFFALO WLI-USB-L11 */
 142 #define USB_BUFFALO_L11G_WR_ID   0x000B /* BUFFALO WLI-USB-L11G-WR */
 143 #define USB_BUFFALO_L11G_ID      0x000D /* BUFFALO WLI-USB-L11G */
 144
 145 #define USB_LUCENT_VENDOR_ID     0x047E /* Lucent Technologies */
 146 #define USB_LUCENT_ORINOCO_ID    0x0300 /* Lucent/Agere Orinoco USB Client */
 147
 148 #define USB_AVAYA8_VENDOR_ID     0x0D98
 149 #define USB_AVAYAE_VENDOR_ID     0x0D9E
 150 #define USB_AVAYA_WIRELESS_ID    0x0300 /* Avaya Wireless USB Card */
 151
 152 #define USB_AGERE_VENDOR_ID      0x0D4E /* Agere Systems */
 153 #define USB_AGERE_MODEL0801_ID   0x1000 /* Wireless USB Card Model 0801 */
 154 #define USB_AGERE_MODEL0802_ID   0x1001 /* Wireless USB Card Model 0802 */
 155 #define USB_AGERE_REBRANDED_ID   0x047A /* WLAN USB Card */
 156
 157 #define USB_ELSA_VENDOR_ID       0x05CC
 158 #define USB_ELSA_AIRLANCER_ID    0x3100 /* ELSA AirLancer USB-11 */
 159
 160 #define USB_LEGEND_VENDOR_ID     0x0E7C
 161 #define USB_LEGEND_JOYNET_ID     0x0300 /* Joynet WLAN USB Card */
 162
 163 #define USB_SAMSUNG_VENDOR_ID    0x04E8
 164 #define USB_SAMSUNG_SEW2001U1_ID 0x5002 /* Samsung SEW-2001u Card */
 165 #define USB_SAMSUNG_SEW2001U2_ID 0x5B11 /* Samsung SEW-2001u Card */
 166 #define USB_SAMSUNG_SEW2003U_ID  0x7011 /* Samsung SEW-2003U Card */
 167
 168 #define USB_IGATE_VENDOR_ID      0x0681
 169 #define USB_IGATE_IGATE_11M_ID   0x0012 /* I-GATE 11M USB Card */
 170
 171 #define USB_FUJITSU_VENDOR_ID    0x0BF8
 172 #define USB_FUJITSU_E1100_ID     0x1002 /* connect2AIR WLAN E-1100 USB */
 173
 174 #define USB_2WIRE_VENDOR_ID      0x1630
 175 #define USB_2WIRE_WIRELESS_ID    0xff81 /* 2Wire Wireless USB adapter */
 176
 177
 178 #define EZUSB_REQUEST_FW_TRANS          0xA0
 179 #define EZUSB_REQUEST_TRIGER            0xAA
 180 #define EZUSB_REQUEST_TRIG_AC           0xAC
 181 #define EZUSB_CPUCS_REG                 0x7F92
 182
 183 #define EZUSB_RID_TX                    0x0700
 184 #define EZUSB_RID_RX                    0x0701
 185 #define EZUSB_RID_INIT1                 0x0702
 186 #define EZUSB_RID_ACK                   0x0710
 187 #define EZUSB_RID_READ_PDA              0x0800
 188 #define EZUSB_RID_PROG_INIT             0x0852
 189 #define EZUSB_RID_PROG_SET_ADDR         0x0853
 190 #define EZUSB_RID_PROG_BYTES            0x0854
 191 #define EZUSB_RID_PROG_END              0x0855
 192 #define EZUSB_RID_DOCMD                 0x0860
 193
 194 /* Recognize info frames */
 195 #define EZUSB_IS_INFO(id)               ((id >= 0xF000) && (id <= 0xF2FF))
 196
 197 #define EZUSB_MAGIC                     0x0210
 198
 199 #define EZUSB_FRAME_DATA                1
 200 #define EZUSB_FRAME_CONTROL             2
 201
 202 #define DEF_TIMEOUT                     (3*HZ)
 203
 204 #define BULK_BUF_SIZE                   2048
 205
 206 #define MAX_DL_SIZE (BULK_BUF_SIZE - sizeof(struct ezusb_packet))
 207
 208 #define FW_BUF_SIZE                     64
 209 #define FW_VAR_OFFSET_PTR               0x359
 210 #define FW_VAR_VALUE                    0
 211 #define FW_HOLE_START                   0x100
 212 #define FW_HOLE_END                     0x300
 213
 214 struct ezusb_packet {
 215         __le16 magic;           /* 0x0210 */
 216         u8 req_reply_count;
 217         u8 ans_reply_count;
 218         __le16 frame_type;      /* 0x01 for data frames, 0x02 otherwise */
 219         __le16 size;            /* transport size */
 220         __le16 crc;             /* CRC up to here */
 221         __le16 hermes_len;
 222         __le16 hermes_rid;
 223         u8 data[0];
 224 } __packed;
 225
 226 /* Table of devices that work or may work with this driver */
 227 static struct usb_device_id ezusb_table[] = {
 228         {USB_DEVICE(USB_COMPAQ_VENDOR_ID, USB_COMPAQ_WL215_ID)},
 229         {USB_DEVICE(USB_COMPAQ_VENDOR_ID, USB_HP_WL215_ID)},
 230         {USB_DEVICE(USB_COMPAQ_VENDOR_ID, USB_COMPAQ_W200_ID)},
 231         {USB_DEVICE(USB_MELCO_VENDOR_ID, USB_BUFFALO_L11_ID)},
 232         {USB_DEVICE(USB_MELCO_VENDOR_ID, USB_BUFFALO_L11G_WR_ID)},
 233         {USB_DEVICE(USB_MELCO_VENDOR_ID, USB_BUFFALO_L11G_ID)},
 234         {USB_DEVICE(USB_LUCENT_VENDOR_ID, USB_LUCENT_ORINOCO_ID)},
 235         {USB_DEVICE(USB_AVAYA8_VENDOR_ID, USB_AVAYA_WIRELESS_ID)},
 236         {USB_DEVICE(USB_AVAYAE_VENDOR_ID, USB_AVAYA_WIRELESS_ID)},
 237         {USB_DEVICE(USB_AGERE_VENDOR_ID, USB_AGERE_MODEL0801_ID)},
 238         {USB_DEVICE(USB_AGERE_VENDOR_ID, USB_AGERE_MODEL0802_ID)},
 239         {USB_DEVICE(USB_ELSA_VENDOR_ID, USB_ELSA_AIRLANCER_ID)},
 240         {USB_DEVICE(USB_LEGEND_VENDOR_ID, USB_LEGEND_JOYNET_ID)},
 241         {USB_DEVICE_VER(USB_SAMSUNG_VENDOR_ID, USB_SAMSUNG_SEW2001U1_ID,
 242                         0, 0)},
 243         {USB_DEVICE(USB_SAMSUNG_VENDOR_ID, USB_SAMSUNG_SEW2001U2_ID)},
 244         {USB_DEVICE(USB_SAMSUNG_VENDOR_ID, USB_SAMSUNG_SEW2003U_ID)},
 245         {USB_DEVICE(USB_IGATE_VENDOR_ID, USB_IGATE_IGATE_11M_ID)},
 246         {USB_DEVICE(USB_FUJITSU_VENDOR_ID, USB_FUJITSU_E1100_ID)},
 247         {USB_DEVICE(USB_2WIRE_VENDOR_ID, USB_2WIRE_WIRELESS_ID)},
 248         {USB_DEVICE(USB_AGERE_VENDOR_ID, USB_AGERE_REBRANDED_ID)},
 249         {}                      /* Terminating entry */
 250 };
 251
 252 MODULE_DEVICE_TABLE(usb, ezusb_table);
 253
 254 /* Structure to hold all of our device specific stuff */
 255 struct ezusb_priv {
 256         struct usb_device *udev;
 257         struct net_device *dev;
 258         struct mutex mtx;
 259         spinlock_t req_lock;
 260         struct list_head req_pending;
 261         struct list_head req_active;
 262         spinlock_t reply_count_lock;
 263         u16 hermes_reg_fake[0x40];
 264         u8 *bap_buf;
 265         struct urb *read_urb;
 266         int read_pipe;
 267         int write_pipe;
 268         u8 reply_count;
 269 };
 270
 271 enum ezusb_state {
 272         EZUSB_CTX_START,
 273         EZUSB_CTX_QUEUED,
 274         EZUSB_CTX_REQ_SUBMITTED,
 275         EZUSB_CTX_REQ_COMPLETE,
 276         EZUSB_CTX_RESP_RECEIVED,
 277         EZUSB_CTX_REQ_TIMEOUT,
 278         EZUSB_CTX_REQ_FAILED,
 279         EZUSB_CTX_RESP_TIMEOUT,
 280         EZUSB_CTX_REQSUBMIT_FAIL,
 281         EZUSB_CTX_COMPLETE,
 282 };
 283
 284 struct request_context {
 285         struct list_head list;
 286         atomic_t refcount;
 287         struct completion done; /* Signals that CTX is dead */
 288         int killed;
 289         struct urb *outurb;     /* OUT for req pkt */
 290         struct ezusb_priv *upriv;
 291         struct ezusb_packet *buf;
 292         int buf_length;
 293         struct timer_list timer;        /* Timeout handling */
 294         enum ezusb_state state; /* Current state */
 295         /* the RID that we will wait for */
 296         u16 out_rid;
 297         u16 in_rid;
 298 };
 299
 300
 301 /* Forward declarations */
 302 static void ezusb_ctx_complete(struct request_context *ctx);
 303 static void ezusb_req_queue_run(struct ezusb_priv *upriv);
 304 static void ezusb_bulk_in_callback(struct urb *urb);
 305
 306 static inline u8 ezusb_reply_inc(u8 count)
 307 {
 308         if (count < 0x7F)
 309                 return count + 1;
 310         else
 311                 return 1;
 312 }
 313
 314 static void ezusb_request_context_put(struct request_context *ctx)
 315 {
 316         if (!atomic_dec_and_test(&ctx->refcount))
 317                 return;
 318
 319         WARN_ON(!ctx->done.done);
 320         BUG_ON(ctx->outurb->status == -EINPROGRESS);
 321         BUG_ON(timer_pending(&ctx->timer));
 322         usb_free_urb(ctx->outurb);
 323         kfree(ctx->buf);
 324         kfree(ctx);
 325 }
 326
 327 static inline void ezusb_mod_timer(struct ezusb_priv *upriv,
 328                                    struct timer_list *timer,
 329                                    unsigned long expire)
 330 {
 331         if (!upriv->udev)
 332                 return;
 333         mod_timer(timer, expire);
 334 }
 335
 336 static void ezusb_request_timerfn(u_long _ctx)
 337 {
 338         struct request_context *ctx = (void *) _ctx;
 339
 340         ctx->outurb->transfer_flags |= URB_ASYNC_UNLINK;
 341         if (usb_unlink_urb(ctx->outurb) == -EINPROGRESS) {
 342                 ctx->state = EZUSB_CTX_REQ_TIMEOUT;
 343         } else {
 344                 ctx->state = EZUSB_CTX_RESP_TIMEOUT;
 345                 dbg("couldn't unlink");
 346                 atomic_inc(&ctx->refcount);
 347                 ctx->killed = 1;
 348                 ezusb_ctx_complete(ctx);
 349                 ezusb_request_context_put(ctx);
 350         }
 351 };
 352
 353 static struct request_context *ezusb_alloc_ctx(struct ezusb_priv *upriv,
 354                                                u16 out_rid, u16 in_rid)
 355 {
 356         struct request_context *ctx;
 357
 358         ctx = kzalloc(sizeof(*ctx), GFP_ATOMIC);
 359         if (!ctx)
 360                 return NULL;
 361
 362         ctx->buf = kmalloc(BULK_BUF_SIZE, GFP_ATOMIC);
 363         if (!ctx->buf) {
 364                 kfree(ctx);
 365                 return NULL;
 366         }
 367         ctx->outurb = usb_alloc_urb(0, GFP_ATOMIC);
 368         if (!ctx->outurb) {
 369                 kfree(ctx->buf);
 370                 kfree(ctx);
 371                 return NULL;
 372         }
 373
 374         ctx->upriv = upriv;
 375         ctx->state = EZUSB_CTX_START;
 376         ctx->out_rid = out_rid;
 377         ctx->in_rid = in_rid;
 378
 379         atomic_set(&ctx->refcount, 1);
 380         init_completion(&ctx->done);
 381
 382         init_timer(&ctx->timer);
 383         ctx->timer.function = ezusb_request_timerfn;
 384         ctx->timer.data = (u_long) ctx;
 385         return ctx;
 386 }
 387
 388
 389 /* Hopefully the real complete_all will soon be exported, in the mean
 390  * while this should work. */
 391 static inline void ezusb_complete_all(struct completion *comp)
 392 {
 393         complete(comp);
 394         complete(comp);
 395         complete(comp);
 396         complete(comp);
 397 }
 398
 399 static void ezusb_ctx_complete(struct request_context *ctx)
 400 {
 401         struct ezusb_priv *upriv = ctx->upriv;
 402         unsigned long flags;
 403
 404         spin_lock_irqsave(&upriv->req_lock, flags);
 405
 406         list_del_init(&ctx->list);
 407         if (upriv->udev) {
 408                 spin_unlock_irqrestore(&upriv->req_lock, flags);
 409                 ezusb_req_queue_run(upriv);
 410                 spin_lock_irqsave(&upriv->req_lock, flags);
 411         }
 412
 413         switch (ctx->state) {
 414         case EZUSB_CTX_COMPLETE:
 415         case EZUSB_CTX_REQSUBMIT_FAIL:
 416         case EZUSB_CTX_REQ_FAILED:
 417         case EZUSB_CTX_REQ_TIMEOUT:
 418         case EZUSB_CTX_RESP_TIMEOUT:
 419                 spin_unlock_irqrestore(&upriv->req_lock, flags);
 420
 421                 if ((ctx->out_rid == EZUSB_RID_TX) && upriv->dev) {
 422                         struct net_device *dev = upriv->dev;
 423                         struct orinoco_private *priv = ndev_priv(dev);
 424                         struct net_device_stats *stats = &priv->stats;
 425
 426                         if (ctx->state != EZUSB_CTX_COMPLETE)
 427                                 stats->tx_errors++;
 428                         else
 429                                 stats->tx_packets++;
 430
 431                         netif_wake_queue(dev);
 432                 }
 433                 ezusb_complete_all(&ctx->done);
 434                 ezusb_request_context_put(ctx);
 435                 break;
 436
 437         default:
 438                 spin_unlock_irqrestore(&upriv->req_lock, flags);
 439                 if (!upriv->udev) {
 440                         /* This is normal, as all request contexts get flushed
 441                          * when the device is disconnected */
 442                         err("Called, CTX not terminating, but device gone");
 443                         ezusb_complete_all(&ctx->done);
 444                         ezusb_request_context_put(ctx);
 445                         break;
 446                 }
 447
 448                 err("Called, CTX not in terminating state.");
 449                 /* Things are really bad if this happens. Just leak
 450                  * the CTX because it may still be linked to the
 451                  * queue or the OUT urb may still be active.
 452                  * Just leaking at least prevents an Oops or Panic.
 453                  */
 454                 break;
 455         }
 456 }
 457
 458 /**
 459  * ezusb_req_queue_run:
 460  * Description:
 461  *      Note: Only one active CTX at any one time, because there's no
 462  *      other (reliable) way to match the response URB to the correct
 463  *      CTX.
 464  **/
 465 static void ezusb_req_queue_run(struct ezusb_priv *upriv)
 466 {
 467         unsigned long flags;
 468         struct request_context *ctx;
 469         int result;
 470
 471         spin_lock_irqsave(&upriv->req_lock, flags);
 472
 473         if (!list_empty(&upriv->req_active))
 474                 goto unlock;
 475
 476         if (list_empty(&upriv->req_pending))
 477                 goto unlock;
 478
 479         ctx =
 480             list_entry(upriv->req_pending.next, struct request_context,
 481                        list);
 482
 483         if (!ctx->upriv->udev)
 484                 goto unlock;
 485
 486         /* We need to split this off to avoid a race condition */
 487         list_move_tail(&ctx->list, &upriv->req_active);
 488
 489         if (ctx->state == EZUSB_CTX_QUEUED) {
 490                 atomic_inc(&ctx->refcount);
 491                 result = usb_submit_urb(ctx->outurb, GFP_ATOMIC);
 492                 if (result) {
 493                         ctx->state = EZUSB_CTX_REQSUBMIT_FAIL;
 494
 495                         spin_unlock_irqrestore(&upriv->req_lock, flags);
 496
 497                         err("Fatal, failed to submit command urb."
 498                             " error=%d\n", result);
 499
 500                         ezusb_ctx_complete(ctx);
 501                         ezusb_request_context_put(ctx);
 502                         goto done;
 503                 }
 504
 505                 ctx->state = EZUSB_CTX_REQ_SUBMITTED;
 506                 ezusb_mod_timer(ctx->upriv, &ctx->timer,
 507                                 jiffies + DEF_TIMEOUT);
 508         }
 509
 510  unlock:
 511         spin_unlock_irqrestore(&upriv->req_lock, flags);
 512
 513  done:
 514         return;
 515 }
 516
 517 static void ezusb_req_enqueue_run(struct ezusb_priv *upriv,
 518                                   struct request_context *ctx)
 519 {
 520         unsigned long flags;
 521
 522         spin_lock_irqsave(&upriv->req_lock, flags);
 523
 524         if (!ctx->upriv->udev) {
 525                 spin_unlock_irqrestore(&upriv->req_lock, flags);
 526                 goto done;
 527         }
 528         atomic_inc(&ctx->refcount);
 529         list_add_tail(&ctx->list, &upriv->req_pending);
 530         spin_unlock_irqrestore(&upriv->req_lock, flags);
 531
 532         ctx->state = EZUSB_CTX_QUEUED;
 533         ezusb_req_queue_run(upriv);
 534
 535  done:
 536         return;
 537 }
 538
 539 static void ezusb_request_out_callback(struct urb *urb)
 540 {
 541         unsigned long flags;
 542         enum ezusb_state state;
 543         struct request_context *ctx = urb->context;
 544         struct ezusb_priv *upriv = ctx->upriv;
 545
 546         spin_lock_irqsave(&upriv->req_lock, flags);
 547
 548         del_timer(&ctx->timer);
 549
 550         if (ctx->killed) {
 551                 spin_unlock_irqrestore(&upriv->req_lock, flags);
 552                 pr_warning("interrupt called with dead ctx");
 553                 goto out;
 554         }
 555
 556         state = ctx->state;
 557
 558         if (urb->status == 0) {
 559                 switch (state) {
 560                 case EZUSB_CTX_REQ_SUBMITTED:
 561                         if (ctx->in_rid) {
 562                                 ctx->state = EZUSB_CTX_REQ_COMPLETE;
 563                                 /* reply URB still pending */
 564                                 ezusb_mod_timer(upriv, &ctx->timer,
 565                                                 jiffies + DEF_TIMEOUT);
 566                                 spin_unlock_irqrestore(&upriv->req_lock,
 567                                                        flags);
 568                                 break;
 569                         }
 570                         /* fall through */
 571                 case EZUSB_CTX_RESP_RECEIVED:
 572                         /* IN already received before this OUT-ACK */
 573                         ctx->state = EZUSB_CTX_COMPLETE;
 574                         spin_unlock_irqrestore(&upriv->req_lock, flags);
 575                         ezusb_ctx_complete(ctx);
 576                         break;
 577
 578                 default:
 579                         spin_unlock_irqrestore(&upriv->req_lock, flags);
 580                         err("Unexpected state(0x%x, %d) in OUT URB",
 581                             state, urb->status);
 582                         break;
 583                 }
 584         } else {
 585                 /* If someone cancels the OUT URB then its status
 586                  * should be either -ECONNRESET or -ENOENT.
 587                  */
 588                 switch (state) {
 589                 case EZUSB_CTX_REQ_SUBMITTED:
 590                 case EZUSB_CTX_RESP_RECEIVED:
 591                         ctx->state = EZUSB_CTX_REQ_FAILED;
 592                         /* fall through */
 593
 594                 case EZUSB_CTX_REQ_FAILED:
 595                 case EZUSB_CTX_REQ_TIMEOUT:
 596                         spin_unlock_irqrestore(&upriv->req_lock, flags);
 597
 598                         ezusb_ctx_complete(ctx);
 599                         break;
 600
 601                 default:
 602                         spin_unlock_irqrestore(&upriv->req_lock, flags);
 603
 604                         err("Unexpected state(0x%x, %d) in OUT URB",
 605                             state, urb->status);
 606                         break;
 607                 }
 608         }
 609  out:
 610         ezusb_request_context_put(ctx);
 611 }
 612
 613 static void ezusb_request_in_callback(struct ezusb_priv *upriv,
 614                                       struct urb *urb)
 615 {
 616         struct ezusb_packet *ans = urb->transfer_buffer;
 617         struct request_context *ctx = NULL;
 618         enum ezusb_state state;
 619         unsigned long flags;
 620
 621         /* Find the CTX on the active queue that requested this URB */
 622         spin_lock_irqsave(&upriv->req_lock, flags);
 623         if (upriv->udev) {
 624                 struct list_head *item;
 625
 626                 list_for_each(item, &upriv->req_active) {
 627                         struct request_context *c;
 628                         int reply_count;
 629
 630                         c = list_entry(item, struct request_context, list);
 631                         reply_count =
 632                             ezusb_reply_inc(c->buf->req_reply_count);
 633                         if ((ans->ans_reply_count == reply_count)
 634                             && (le16_to_cpu(ans->hermes_rid) == c->in_rid)) {
 635                                 ctx = c;
 636                                 break;
 637                         }
 638                         dbg("Skipped (0x%x/0x%x) (%d/%d)",
 639                             le16_to_cpu(ans->hermes_rid),
 640                             c->in_rid, ans->ans_reply_count, reply_count);
 641                 }
 642         }
 643
 644         if (ctx == NULL) {
 645                 spin_unlock_irqrestore(&upriv->req_lock, flags);
 646                 err("%s: got unexpected RID: 0x%04X", __func__,
 647                     le16_to_cpu(ans->hermes_rid));
 648                 ezusb_req_queue_run(upriv);
 649                 return;
 650         }
 651
 652         /* The data we want is in the in buffer, exchange */
 653         urb->transfer_buffer = ctx->buf;
 654         ctx->buf = (void *) ans;
 655         ctx->buf_length = urb->actual_length;
 656
 657         state = ctx->state;
 658         switch (state) {
 659         case EZUSB_CTX_REQ_SUBMITTED:
 660                 /* We have received our response URB before
 661                  * our request has been acknowledged. Do NOT
 662                  * destroy our CTX yet, because our OUT URB
 663                  * is still alive ...
 664                  */
 665                 ctx->state = EZUSB_CTX_RESP_RECEIVED;
 666                 spin_unlock_irqrestore(&upriv->req_lock, flags);
 667
 668                 /* Let the machine continue running. */
 669                 break;
 670
 671         case EZUSB_CTX_REQ_COMPLETE:
 672                 /* This is the usual path: our request
 673                  * has already been acknowledged, and
 674                  * we have now received the reply.
 675                  */
 676                 ctx->state = EZUSB_CTX_COMPLETE;
 677
 678                 /* Stop the intimer */
 679                 del_timer(&ctx->timer);
 680                 spin_unlock_irqrestore(&upriv->req_lock, flags);
 681
 682                 /* Call the completion handler */
 683                 ezusb_ctx_complete(ctx);
 684                 break;
 685
 686         default:
 687                 spin_unlock_irqrestore(&upriv->req_lock, flags);
 688
 689                 pr_warning("Matched IN URB, unexpected context state(0x%x)",
 690                      state);
 691                 /* Throw this CTX away and try submitting another */
 692                 del_timer(&ctx->timer);
 693                 ctx->outurb->transfer_flags |= URB_ASYNC_UNLINK;
 694                 usb_unlink_urb(ctx->outurb);
 695                 ezusb_req_queue_run(upriv);
 696                 break;
 697         }                       /* switch */
 698 }
 699
 700
 701 static void ezusb_req_ctx_wait(struct ezusb_priv *upriv,
 702                                struct request_context *ctx)
 703 {
 704         switch (ctx->state) {
 705         case EZUSB_CTX_QUEUED:
 706         case EZUSB_CTX_REQ_SUBMITTED:
 707         case EZUSB_CTX_REQ_COMPLETE:
 708         case EZUSB_CTX_RESP_RECEIVED:
 709                 if (in_softirq()) {
 710                         /* If we get called from a timer, timeout timers don't
 711                          * get the chance to run themselves. So we make sure
 712                          * that we don't sleep for ever */
 713                         int msecs = DEF_TIMEOUT * (1000 / HZ);
 714                         while (!ctx->done.done && msecs--)
 715                                 udelay(1000);
 716                 } else {
 717                         wait_event_interruptible(ctx->done.wait,
 718                                                  ctx->done.done);
 719                 }
 720                 break;
 721         default:
 722                 /* Done or failed - nothing to wait for */
 723                 break;
 724         }
 725 }
 726
 727 static inline u16 build_crc(struct ezusb_packet *data)
 728 {
 729         u16 crc = 0;
 730         u8 *bytes = (u8 *)data;
 731         int i;
 732
 733         for (i = 0; i < 8; i++)
 734                 crc = (crc << 1) + bytes[i];
 735
 736         return crc;
 737 }
 738
 739 /**
 740  * ezusb_fill_req:
 741  *
 742  * if data == NULL and length > 0 the data is assumed to be already in
 743  * the target buffer and only the header is filled.
 744  *
 745  */
 746 static int ezusb_fill_req(struct ezusb_packet *req, u16 length, u16 rid,
 747                           const void *data, u16 frame_type, u8 reply_count)
 748 {
 749         int total_size = sizeof(*req) + length;
 750
 751         BUG_ON(total_size > BULK_BUF_SIZE);
 752
 753         req->magic = cpu_to_le16(EZUSB_MAGIC);
 754         req->req_reply_count = reply_count;
 755         req->ans_reply_count = 0;
 756         req->frame_type = cpu_to_le16(frame_type);
 757         req->size = cpu_to_le16(length + 4);
 758         req->crc = cpu_to_le16(build_crc(req));
 759         req->hermes_len = cpu_to_le16(HERMES_BYTES_TO_RECLEN(length));
 760         req->hermes_rid = cpu_to_le16(rid);
 761         if (data)
 762                 memcpy(req->data, data, length);
 763         return total_size;
 764 }
 765
 766 static int ezusb_submit_in_urb(struct ezusb_priv *upriv)
 767 {
 768         int retval = 0;
 769         void *cur_buf = upriv->read_urb->transfer_buffer;
 770
 771         if (upriv->read_urb->status == -EINPROGRESS) {
 772                 dbg("urb busy, not resubmiting");
 773                 retval = -EBUSY;
 774                 goto exit;
 775         }
 776         usb_fill_bulk_urb(upriv->read_urb, upriv->udev, upriv->read_pipe,
 777                           cur_buf, BULK_BUF_SIZE,
 778                           ezusb_bulk_in_callback, upriv);
 779         upriv->read_urb->transfer_flags = 0;
 780         retval = usb_submit_urb(upriv->read_urb, GFP_ATOMIC);
 781         if (retval)
 782                 err("%s submit failed %d", __func__, retval);
 783
 784  exit:
 785         return retval;
 786 }
 787
 788 static inline int ezusb_8051_cpucs(struct ezusb_priv *upriv, int reset)
 789 {
 790         u8 res_val = reset;     /* avoid argument promotion */
 791
 792         if (!upriv->udev) {
 793                 err("%s: !upriv->udev", __func__);
 794                 return -EFAULT;
 795         }
 796         return usb_control_msg(upriv->udev,
 797                                usb_sndctrlpipe(upriv->udev, 0),
 798                                EZUSB_REQUEST_FW_TRANS,
 799                                USB_TYPE_VENDOR | USB_RECIP_DEVICE |
 800                                USB_DIR_OUT, EZUSB_CPUCS_REG, 0, &res_val,
 801                                sizeof(res_val), DEF_TIMEOUT);
 802 }
 803
 804 static int ezusb_firmware_download(struct ezusb_priv *upriv,
 805                                    struct ez_usb_fw *fw)
 806 {
 807         u8 fw_buffer[FW_BUF_SIZE];
 808         int retval, addr;
 809         int variant_offset;
 810
 811         /*
 812          * This byte is 1 and should be replaced with 0.  The offset is
 813          * 0x10AD in version 0.0.6.  The byte in question should follow
 814          * the end of the code pointed to by the jump in the beginning
 815          * of the firmware.  Also, it is read by code located at 0x358.
 816          */
 817         variant_offset = be16_to_cpup((__be16 *) &fw->code[FW_VAR_OFFSET_PTR]);
 818         if (variant_offset >= fw->size) {
 819                 printk(KERN_ERR PFX "Invalid firmware variant offset: "
 820                        "0x%04x\n", variant_offset);
 821                 retval = -EINVAL;
 822                 goto fail;
 823         }
 824
 825         retval = ezusb_8051_cpucs(upriv, 1);
 826         if (retval < 0)
 827                 goto fail;
 828         for (addr = 0; addr < fw->size; addr += FW_BUF_SIZE) {
 829                 /* 0x100-0x300 should be left alone, it contains card
 830                  * specific data, like USB enumeration information */
 831                 if ((addr >= FW_HOLE_START) && (addr < FW_HOLE_END))
 832                         continue;
 833
 834                 memcpy(fw_buffer, &fw->code[addr], FW_BUF_SIZE);
 835                 if (variant_offset >= addr &&
 836                     variant_offset < addr + FW_BUF_SIZE) {
 837                         dbg("Patching card_variant byte at 0x%04X",
 838                             variant_offset);
 839                         fw_buffer[variant_offset - addr] = FW_VAR_VALUE;
 840                 }
 841                 retval = usb_control_msg(upriv->udev,
 842                                          usb_sndctrlpipe(upriv->udev, 0),
 843                                          EZUSB_REQUEST_FW_TRANS,
 844                                          USB_TYPE_VENDOR | USB_RECIP_DEVICE
 845                                          | USB_DIR_OUT,
 846                                          addr, 0x0,
 847                                          fw_buffer, FW_BUF_SIZE,
 848                                          DEF_TIMEOUT);
 849
 850                 if (retval < 0)
 851                         goto fail;
 852         }
 853         retval = ezusb_8051_cpucs(upriv, 0);
 854         if (retval < 0)
 855                 goto fail;
 856
 857         goto exit;
 858  fail:
 859         printk(KERN_ERR PFX "Firmware download failed, error %d\n",
 860                retval);
 861  exit:
 862         return retval;
 863 }
 864
 865 static int ezusb_access_ltv(struct ezusb_priv *upriv,
 866                             struct request_context *ctx,
 867                             u16 length, const void *data, u16 frame_type,
 868                             void *ans_buff, int ans_size, u16 *ans_length)
 869 {
 870         int req_size;
 871         int retval = 0;
 872         enum ezusb_state state;
 873
 874         BUG_ON(in_irq());
 875
 876         if (!upriv->udev) {
 877                 dbg("Device disconnected");
 878                 return -ENODEV;
 879         }
 880
 881         if (upriv->read_urb->status != -EINPROGRESS)
 882                 err("%s: in urb not pending", __func__);
 883
 884         /* protect upriv->reply_count, guarantee sequential numbers */
 885         spin_lock_bh(&upriv->reply_count_lock);
 886         req_size = ezusb_fill_req(ctx->buf, length, ctx->out_rid, data,
 887                                   frame_type, upriv->reply_count);
 888         usb_fill_bulk_urb(ctx->outurb, upriv->udev, upriv->write_pipe,
 889                           ctx->buf, req_size,
 890                           ezusb_request_out_callback, ctx);
 891
 892         if (ctx->in_rid)
 893                 upriv->reply_count = ezusb_reply_inc(upriv->reply_count);
 894
 895         ezusb_req_enqueue_run(upriv, ctx);
 896
 897         spin_unlock_bh(&upriv->reply_count_lock);
 898
 899         if (ctx->in_rid)
 900                 ezusb_req_ctx_wait(upriv, ctx);
 901
 902         state = ctx->state;
 903         switch (state) {
 904         case EZUSB_CTX_COMPLETE:
 905                 retval = ctx->outurb->status;
 906                 break;
 907
 908         case EZUSB_CTX_QUEUED:
 909         case EZUSB_CTX_REQ_SUBMITTED:
 910                 if (!ctx->in_rid)
 911                         break;
 912         default:
 913                 err("%s: Unexpected context state %d", __func__,
 914                     state);
 915                 /* fall though */
 916         case EZUSB_CTX_REQ_TIMEOUT:
 917         case EZUSB_CTX_REQ_FAILED:
 918         case EZUSB_CTX_RESP_TIMEOUT:
 919         case EZUSB_CTX_REQSUBMIT_FAIL:
 920                 printk(KERN_ERR PFX "Access failed, resetting (state %d,"
 921                        " reply_count %d)\n", state, upriv->reply_count);
 922                 upriv->reply_count = 0;
 923                 if (state == EZUSB_CTX_REQ_TIMEOUT
 924                     || state == EZUSB_CTX_RESP_TIMEOUT) {
 925                         printk(KERN_ERR PFX "ctx timed out\n");
 926                         retval = -ETIMEDOUT;
 927                 } else {
 928                         printk(KERN_ERR PFX "ctx failed\n");
 929                         retval = -EFAULT;
 930                 }
 931                 goto exit;
 932                 break;
 933         }
 934         if (ctx->in_rid) {
 935                 struct ezusb_packet *ans = ctx->buf;
 936                 int exp_len;
 937
 938                 if (ans->hermes_len != 0)
 939                         exp_len = le16_to_cpu(ans->hermes_len) * 2 + 12;
 940                 else
 941                         exp_len = 14;
 942
 943                 if (exp_len != ctx->buf_length) {
 944                         err("%s: length mismatch for RID 0x%04x: "
 945                             "expected %d, got %d", __func__,
 946                             ctx->in_rid, exp_len, ctx->buf_length);
 947                         retval = -EIO;
 948                         goto exit;
 949                 }
 950
 951                 if (ans_buff)
 952                         memcpy(ans_buff, ans->data,
 953                                min_t(int, exp_len, ans_size));
 954                 if (ans_length)
 955                         *ans_length = le16_to_cpu(ans->hermes_len);
 956         }
 957  exit:
 958         ezusb_request_context_put(ctx);
 959         return retval;
 960 }
 961
 962 static int ezusb_write_ltv(hermes_t *hw, int bap, u16 rid,
 963                            u16 length, const void *data)
 964 {
 965         struct ezusb_priv *upriv = hw->priv;
 966         u16 frame_type;
 967         struct request_context *ctx;
 968
 969         if (length == 0)
 970                 return -EINVAL;
 971
 972         length = HERMES_RECLEN_TO_BYTES(length);
 973
 974         /* On memory mapped devices HERMES_RID_CNFGROUPADDRESSES can be
 975          * set to be empty, but the USB bridge doesn't like it */
 976         if (length == 0)
 977                 return 0;
 978
 979         ctx = ezusb_alloc_ctx(upriv, rid, EZUSB_RID_ACK);
 980         if (!ctx)
 981                 return -ENOMEM;
 982
 983         if (rid == EZUSB_RID_TX)
 984                 frame_type = EZUSB_FRAME_DATA;
 985         else
 986                 frame_type = EZUSB_FRAME_CONTROL;
 987
 988         return ezusb_access_ltv(upriv, ctx, length, data, frame_type,
 989                                 NULL, 0, NULL);
 990 }
 991
 992 static int ezusb_read_ltv(hermes_t *hw, int bap, u16 rid,
 993                           unsigned bufsize, u16 *length, void *buf)
 994 {
 995         struct ezusb_priv *upriv = hw->priv;
 996         struct request_context *ctx;
 997
 998         if ((bufsize < 0) || (bufsize % 2))
 999                 return -EINVAL;
1000
1001         ctx = ezusb_alloc_ctx(upriv, rid, rid);
1002         if (!ctx)
1003                 return -ENOMEM;
1004
1005         return ezusb_access_ltv(upriv, ctx, 0, NULL, EZUSB_FRAME_CONTROL,
1006                                 buf, bufsize, length);
1007 }
1008
1009 static int ezusb_doicmd_wait(hermes_t *hw, u16 cmd, u16 parm0, u16 parm1,
1010                              u16 parm2, struct hermes_response *resp)
1011 {
1012         struct ezusb_priv *upriv = hw->priv;
1013         struct request_context *ctx;
1014
1015         __le16 data[4] = {
1016                 cpu_to_le16(cmd),
1017                 cpu_to_le16(parm0),
1018                 cpu_to_le16(parm1),
1019                 cpu_to_le16(parm2),
1020         };
1021         dbg("0x%04X, parm0 0x%04X, parm1 0x%04X, parm2 0x%04X",
1022             cmd, parm0, parm1, parm2);
1023         ctx = ezusb_alloc_ctx(upriv, EZUSB_RID_DOCMD, EZUSB_RID_ACK);
1024         if (!ctx)
1025                 return -ENOMEM;
1026
1027         return ezusb_access_ltv(upriv, ctx, sizeof(data), &data,
1028                                 EZUSB_FRAME_CONTROL, NULL, 0, NULL);
1029 }
1030
1031 static int ezusb_docmd_wait(hermes_t *hw, u16 cmd, u16 parm0,
1032                             struct hermes_response *resp)
1033 {
1034         struct ezusb_priv *upriv = hw->priv;
1035         struct request_context *ctx;
1036
1037         __le16 data[4] = {
1038                 cpu_to_le16(cmd),
1039                 cpu_to_le16(parm0),
1040                 0,
1041                 0,
1042         };
1043         dbg("0x%04X, parm0 0x%04X", cmd, parm0);
1044         ctx = ezusb_alloc_ctx(upriv, EZUSB_RID_DOCMD, EZUSB_RID_ACK);
1045         if (!ctx)
1046                 return -ENOMEM;
1047
1048         return ezusb_access_ltv(upriv, ctx, sizeof(data), &data,
1049                                 EZUSB_FRAME_CONTROL, NULL, 0, NULL);
1050 }
1051
1052 static int ezusb_bap_pread(struct hermes *hw, int bap,
1053                            void *buf, int len, u16 id, u16 offset)
1054 {
1055         struct ezusb_priv *upriv = hw->priv;
1056         struct ezusb_packet *ans = (void *) upriv->read_urb->transfer_buffer;
1057         int actual_length = upriv->read_urb->actual_length;
1058
1059         if (id == EZUSB_RID_RX) {
1060                 if ((sizeof(*ans) + offset + len) > actual_length) {
1061                         printk(KERN_ERR PFX "BAP read beyond buffer end "
1062                                "in rx frame\n");
1063                         return -EINVAL;
1064                 }
1065                 memcpy(buf, ans->data + offset, len);
1066                 return 0;
1067         }
1068
1069         if (EZUSB_IS_INFO(id)) {
1070                 /* Include 4 bytes for length/type */
1071                 if ((sizeof(*ans) + offset + len - 4) > actual_length) {
1072                         printk(KERN_ERR PFX "BAP read beyond buffer end "
1073                                "in info frame\n");
1074                         return -EFAULT;
1075                 }
1076                 memcpy(buf, ans->data + offset - 4, len);
1077         } else {
1078                 printk(KERN_ERR PFX "Unexpected fid 0x%04x\n", id);
1079                 return -EINVAL;
1080         }
1081
1082         return 0;
1083 }
1084
1085 static int ezusb_read_pda(struct hermes *hw, __le16 *pda,
1086                           u32 pda_addr, u16 pda_len)
1087 {
1088         struct ezusb_priv *upriv = hw->priv;
1089         struct request_context *ctx;
1090         __le16 data[] = {
1091                 cpu_to_le16(pda_addr & 0xffff),
1092                 cpu_to_le16(pda_len - 4)
1093         };
1094         ctx = ezusb_alloc_ctx(upriv, EZUSB_RID_READ_PDA, EZUSB_RID_READ_PDA);
1095         if (!ctx)
1096                 return -ENOMEM;
1097
1098         /* wl_lkm does not include PDA size in the PDA area.
1099          * We will pad the information into pda, so other routines
1100          * don't have to be modified */
1101         pda[0] = cpu_to_le16(pda_len - 2);
1102         /* Includes CFG_PROD_DATA but not itself */
1103         pda[1] = cpu_to_le16(0x0800); /* CFG_PROD_DATA */
1104
1105         return ezusb_access_ltv(upriv, ctx, sizeof(data), &data,
1106                                 EZUSB_FRAME_CONTROL, &pda[2], pda_len - 4,
1107                                 NULL);
1108 }
1109
1110 static int ezusb_program_init(struct hermes *hw, u32 entry_point)
1111 {
1112         struct ezusb_priv *upriv = hw->priv;
1113         struct request_context *ctx;
1114         __le32 data = cpu_to_le32(entry_point);
1115
1116         ctx = ezusb_alloc_ctx(upriv, EZUSB_RID_PROG_INIT, EZUSB_RID_ACK);
1117         if (!ctx)
1118                 return -ENOMEM;
1119
1120         return ezusb_access_ltv(upriv, ctx, sizeof(data), &data,
1121                                 EZUSB_FRAME_CONTROL, NULL, 0, NULL);
1122 }
1123
1124 static int ezusb_program_end(struct hermes *hw)
1125 {
1126         struct ezusb_priv *upriv = hw->priv;
1127         struct request_context *ctx;
1128
1129         ctx = ezusb_alloc_ctx(upriv, EZUSB_RID_PROG_END, EZUSB_RID_ACK);
1130         if (!ctx)
1131                 return -ENOMEM;
1132
1133         return ezusb_access_ltv(upriv, ctx, 0, NULL,
1134                                 EZUSB_FRAME_CONTROL, NULL, 0, NULL);
1135 }
1136
1137 static int ezusb_program_bytes(struct hermes *hw, const char *buf,
1138                                u32 addr, u32 len)
1139 {
1140         struct ezusb_priv *upriv = hw->priv;
1141         struct request_context *ctx;
1142         __le32 data = cpu_to_le32(addr);
1143         int err;
1144
1145         ctx = ezusb_alloc_ctx(upriv, EZUSB_RID_PROG_SET_ADDR, EZUSB_RID_ACK);
1146         if (!ctx)
1147                 return -ENOMEM;
1148
1149         err = ezusb_access_ltv(upriv, ctx, sizeof(data), &data,
1150                                EZUSB_FRAME_CONTROL, NULL, 0, NULL);
1151         if (err)
1152                 return err;
1153
1154         ctx = ezusb_alloc_ctx(upriv, EZUSB_RID_PROG_BYTES, EZUSB_RID_ACK);
1155         if (!ctx)
1156                 return -ENOMEM;
1157
1158         return ezusb_access_ltv(upriv, ctx, len, buf,
1159                                 EZUSB_FRAME_CONTROL, NULL, 0, NULL);
1160 }
1161
1162 static int ezusb_program(struct hermes *hw, const char *buf,
1163                          u32 addr, u32 len)
1164 {
1165         u32 ch_addr;
1166         u32 ch_len;
1167         int err = 0;
1168
1169         /* We can only send 2048 bytes out of the bulk xmit at a time,
1170          * so we have to split any programming into chunks of <2048
1171          * bytes. */
1172
1173         ch_len = (len < MAX_DL_SIZE) ? len : MAX_DL_SIZE;
1174         ch_addr = addr;
1175
1176         while (ch_addr < (addr + len)) {
1177                 pr_debug("Programming subblock of length %d "
1178                          "to address 0x%08x. Data @ %p\n",
1179                          ch_len, ch_addr, &buf[ch_addr - addr]);
1180
1181                 err = ezusb_program_bytes(hw, &buf[ch_addr - addr],
1182                                           ch_addr, ch_len);
1183                 if (err)
1184                         break;
1185
1186                 ch_addr += ch_len;
1187                 ch_len = ((addr + len - ch_addr) < MAX_DL_SIZE) ?
1188                         (addr + len - ch_addr) : MAX_DL_SIZE;
1189         }
1190
1191         return err;
1192 }
1193
1194 static netdev_tx_t ezusb_xmit(struct sk_buff *skb, struct net_device *dev)
1195 {
1196         struct orinoco_private *priv = ndev_priv(dev);
1197         struct net_device_stats *stats = &priv->stats;
1198         struct ezusb_priv *upriv = priv->card;
1199         u8 mic[MICHAEL_MIC_LEN+1];
1200         int err = 0;
1201         int tx_control;
1202         unsigned long flags;
1203         struct request_context *ctx;
1204         u8 *buf;
1205         int tx_size;
1206
1207         if (!netif_running(dev)) {
1208                 printk(KERN_ERR "%s: Tx on stopped device!\n",
1209                        dev->name);
1210                 return NETDEV_TX_BUSY;
1211         }
1212
1213         if (netif_queue_stopped(dev)) {
1214                 printk(KERN_DEBUG "%s: Tx while transmitter busy!\n",
1215                        dev->name);
1216                 return NETDEV_TX_BUSY;
1217         }
1218
1219         if (orinoco_lock(priv, &flags) != 0) {
1220                 printk(KERN_ERR
1221                        "%s: ezusb_xmit() called while hw_unavailable\n",
1222                        dev->name);
1223                 return NETDEV_TX_BUSY;
1224         }
1225
1226         if (!netif_carrier_ok(dev) ||
1227             (priv->iw_mode == NL80211_IFTYPE_MONITOR)) {
1228                 /* Oops, the firmware hasn't established a connection,
1229                    silently drop the packet (this seems to be the
1230                    safest approach). */
1231                 goto drop;
1232         }
1233
1234         /* Check packet length */
1235         if (skb->len < ETH_HLEN)
1236                 goto drop;
1237
1238         ctx = ezusb_alloc_ctx(upriv, EZUSB_RID_TX, 0);
1239         if (!ctx)
1240                 goto busy;
1241
1242         memset(ctx->buf, 0, BULK_BUF_SIZE);
1243         buf = ctx->buf->data;
1244
1245         tx_control = 0;
1246
1247         err = orinoco_process_xmit_skb(skb, dev, priv, &tx_control,
1248                                        &mic[0]);
1249         if (err)
1250                 goto drop;
1251
1252         {
1253                 __le16 *tx_cntl = (__le16 *)buf;
1254                 *tx_cntl = cpu_to_le16(tx_control);
1255                 buf += sizeof(*tx_cntl);
1256         }
1257
1258         memcpy(buf, skb->data, skb->len);
1259         buf += skb->len;
1260
1261         if (tx_control & HERMES_TXCTRL_MIC) {
1262                 u8 *m = mic;
1263                 /* Mic has been offset so it can be copied to an even
1264                  * address. We're copying eveything anyway, so we
1265                  * don't need to copy that first byte. */
1266                 if (skb->len % 2)
1267                         m++;
1268                 memcpy(buf, m, MICHAEL_MIC_LEN);
1269                 buf += MICHAEL_MIC_LEN;
1270         }
1271
1272         /* Finally, we actually initiate the send */
1273         netif_stop_queue(dev);
1274
1275         /* The card may behave better if we send evenly sized usb transfers */
1276         tx_size = ALIGN(buf - ctx->buf->data, 2);
1277
1278         err = ezusb_access_ltv(upriv, ctx, tx_size, NULL,
1279                                EZUSB_FRAME_DATA, NULL, 0, NULL);
1280
1281         if (err) {
1282                 netif_start_queue(dev);
1283                 if (net_ratelimit())
1284                         printk(KERN_ERR "%s: Error %d transmitting packet\n",
1285                                 dev->name, err);
1286                 goto busy;
1287         }
1288
1289         dev->trans_start = jiffies;
1290         stats->tx_bytes += skb->len;
1291         goto ok;
1292
1293  drop:
1294         stats->tx_errors++;
1295         stats->tx_dropped++;
1296
1297  ok:
1298         orinoco_unlock(priv, &flags);
1299         dev_kfree_skb(skb);
1300         return NETDEV_TX_OK;
1301
1302  busy:
1303         orinoco_unlock(priv, &flags);
1304         return NETDEV_TX_BUSY;
1305 }
1306
1307 static int ezusb_allocate(struct hermes *hw, u16 size, u16 *fid)
1308 {
1309         *fid = EZUSB_RID_TX;
1310         return 0;
1311 }
1312
1313
1314 static int ezusb_hard_reset(struct orinoco_private *priv)
1315 {
1316         struct ezusb_priv *upriv = priv->card;
1317         int retval = ezusb_8051_cpucs(upriv, 1);
1318
1319         if (retval < 0) {
1320                 err("Failed to reset");
1321                 return retval;
1322         }
1323
1324         retval = ezusb_8051_cpucs(upriv, 0);
1325         if (retval < 0) {
1326                 err("Failed to unreset");
1327                 return retval;
1328         }
1329
1330         dbg("sending control message");
1331         retval = usb_control_msg(upriv->udev,
1332                                  usb_sndctrlpipe(upriv->udev, 0),
1333                                  EZUSB_REQUEST_TRIGER,
1334                                  USB_TYPE_VENDOR | USB_RECIP_DEVICE |
1335                                  USB_DIR_OUT, 0x0, 0x0, NULL, 0,
1336                                  DEF_TIMEOUT);
1337         if (retval < 0) {
1338                 err("EZUSB_REQUEST_TRIGER failed retval %d", retval);
1339                 return retval;
1340         }
1341 #if 0
1342         dbg("Sending EZUSB_REQUEST_TRIG_AC");
1343         retval = usb_control_msg(upriv->udev,
1344                                  usb_sndctrlpipe(upriv->udev, 0),
1345                                  EZUSB_REQUEST_TRIG_AC,
1346                                  USB_TYPE_VENDOR | USB_RECIP_DEVICE |
1347                                  USB_DIR_OUT, 0x00FA, 0x0, NULL, 0,
1348                                  DEF_TIMEOUT);
1349         if (retval < 0) {
1350                 err("EZUSB_REQUEST_TRIG_AC failed retval %d", retval);
1351                 return retval;
1352         }
1353 #endif
1354
1355         return 0;
1356 }
1357
1358
1359 static int ezusb_init(hermes_t *hw)
1360 {
1361         struct ezusb_priv *upriv = hw->priv;
1362         int retval;
1363
1364         BUG_ON(in_interrupt());
1365         BUG_ON(!upriv);
1366
1367         upriv->reply_count = 0;
1368         /* Write the MAGIC number on the simulated registers to keep
1369          * orinoco.c happy */
1370         hermes_write_regn(hw, SWSUPPORT0, HERMES_MAGIC);
1371         hermes_write_regn(hw, RXFID, EZUSB_RID_RX);
1372
1373         usb_kill_urb(upriv->read_urb);
1374         ezusb_submit_in_urb(upriv);
1375
1376         retval = ezusb_write_ltv(hw, 0, EZUSB_RID_INIT1,
1377                                  HERMES_BYTES_TO_RECLEN(2), "\x10\x00");
1378         if (retval < 0) {
1379                 printk(KERN_ERR PFX "EZUSB_RID_INIT1 error %d\n", retval);
1380                 return retval;
1381         }
1382
1383         retval = ezusb_docmd_wait(hw, HERMES_CMD_INIT, 0, NULL);
1384         if (retval < 0) {
1385                 printk(KERN_ERR PFX "HERMES_CMD_INIT error %d\n", retval);
1386                 return retval;
1387         }
1388
1389         return 0;
1390 }
1391
1392 static void ezusb_bulk_in_callback(struct urb *urb)
1393 {
1394         struct ezusb_priv *upriv = (struct ezusb_priv *) urb->context;
1395         struct ezusb_packet *ans = urb->transfer_buffer;
1396         u16 crc;
1397         u16 hermes_rid;
1398
1399         if (upriv->udev == NULL) {
1400                 dbg("disconnected");
1401                 return;
1402         }
1403
1404         if (urb->status == -ETIMEDOUT) {
1405                 /* When a device gets unplugged we get this every time
1406                  * we resubmit, flooding the logs.  Since we don't use
1407                  * USB timeouts, it shouldn't happen any other time*/
1408                 pr_warning("%s: urb timed out, not resubmiting", __func__);
1409                 return;
1410         }
1411         if (urb->status == -ECONNABORTED) {
1412                 pr_warning("%s: connection abort, resubmiting urb",
1413                      __func__);
1414                 goto resubmit;
1415         }
1416         if ((urb->status == -EILSEQ)
1417             || (urb->status == -ENOENT)
1418             || (urb->status == -ECONNRESET)) {
1419                 dbg("status %d, not resubmiting", urb->status);
1420                 return;
1421         }
1422         if (urb->status)
1423                 dbg("status: %d length: %d",
1424                     urb->status, urb->actual_length);
1425         if (urb->actual_length < sizeof(*ans)) {
1426                 err("%s: short read, ignoring", __func__);
1427                 goto resubmit;
1428         }
1429         crc = build_crc(ans);
1430         if (le16_to_cpu(ans->crc) != crc) {
1431                 err("CRC error, ignoring packet");
1432                 goto resubmit;
1433         }
1434
1435         hermes_rid = le16_to_cpu(ans->hermes_rid);
1436         if ((hermes_rid != EZUSB_RID_RX) && !EZUSB_IS_INFO(hermes_rid)) {
1437                 ezusb_request_in_callback(upriv, urb);
1438         } else if (upriv->dev) {
1439                 struct net_device *dev = upriv->dev;
1440                 struct orinoco_private *priv = ndev_priv(dev);
1441                 hermes_t *hw = &priv->hw;
1442
1443                 if (hermes_rid == EZUSB_RID_RX) {
1444                         __orinoco_ev_rx(dev, hw);
1445                 } else {
1446                         hermes_write_regn(hw, INFOFID,
1447                                           le16_to_cpu(ans->hermes_rid));
1448                         __orinoco_ev_info(dev, hw);
1449                 }
1450         }
1451
1452  resubmit:
1453         if (upriv->udev)
1454                 ezusb_submit_in_urb(upriv);
1455 }
1456
1457 static inline void ezusb_delete(struct ezusb_priv *upriv)
1458 {
1459         struct net_device *dev;
1460         struct list_head *item;
1461         struct list_head *tmp_item;
1462         unsigned long flags;
1463
1464         BUG_ON(in_interrupt());
1465         BUG_ON(!upriv);
1466
1467         dev = upriv->dev;
1468         mutex_lock(&upriv->mtx);
1469
1470         upriv->udev = NULL;     /* No timer will be rearmed from here */
1471
1472         usb_kill_urb(upriv->read_urb);
1473
1474         spin_lock_irqsave(&upriv->req_lock, flags);
1475         list_for_each_safe(item, tmp_item, &upriv->req_active) {
1476                 struct request_context *ctx;
1477                 int err;
1478
1479                 ctx = list_entry(item, struct request_context, list);
1480                 atomic_inc(&ctx->refcount);
1481
1482                 ctx->outurb->transfer_flags |= URB_ASYNC_UNLINK;
1483                 err = usb_unlink_urb(ctx->outurb);
1484
1485                 spin_unlock_irqrestore(&upriv->req_lock, flags);
1486                 if (err == -EINPROGRESS)
1487                         wait_for_completion(&ctx->done);
1488
1489                 del_timer_sync(&ctx->timer);
1490                 /* FIXME: there is an slight chance for the irq handler to
1491                  * be running */
1492                 if (!list_empty(&ctx->list))
1493                         ezusb_ctx_complete(ctx);
1494
1495                 ezusb_request_context_put(ctx);
1496                 spin_lock_irqsave(&upriv->req_lock, flags);
1497         }
1498         spin_unlock_irqrestore(&upriv->req_lock, flags);
1499
1500         list_for_each_safe(item, tmp_item, &upriv->req_pending)
1501             ezusb_ctx_complete(list_entry(item,
1502                                           struct request_context, list));
1503
1504         if (upriv->read_urb && upriv->read_urb->status == -EINPROGRESS)
1505                 printk(KERN_ERR PFX "Some URB in progress\n");
1506
1507         mutex_unlock(&upriv->mtx);
1508
1509         if (upriv->read_urb) {
1510                 kfree(upriv->read_urb->transfer_buffer);
1511                 usb_free_urb(upriv->read_urb);
1512         }
1513         kfree(upriv->bap_buf);
1514         if (upriv->dev) {
1515                 struct orinoco_private *priv = ndev_priv(upriv->dev);
1516                 orinoco_if_del(priv);
1517                 free_orinocodev(priv);
1518         }
1519 }
1520
1521 static void ezusb_lock_irqsave(spinlock_t *lock,
1522                                unsigned long *flags) __acquires(lock)
1523 {
1524         spin_lock_bh(lock);
1525 }
1526
1527 static void ezusb_unlock_irqrestore(spinlock_t *lock,
1528                                     unsigned long *flags) __releases(lock)
1529 {
1530         spin_unlock_bh(lock);
1531 }
1532
1533 static void ezusb_lock_irq(spinlock_t *lock) __acquires(lock)
1534 {
1535         spin_lock_bh(lock);
1536 }
1537
1538 static void ezusb_unlock_irq(spinlock_t *lock) __releases(lock)
1539 {
1540         spin_unlock_bh(lock);
1541 }
1542
1543 static const struct hermes_ops ezusb_ops = {
1544         .init = ezusb_init,
1545         .cmd_wait = ezusb_docmd_wait,
1546         .init_cmd_wait = ezusb_doicmd_wait,
1547         .allocate = ezusb_allocate,
1548         .read_ltv = ezusb_read_ltv,
1549         .write_ltv = ezusb_write_ltv,
1550         .bap_pread = ezusb_bap_pread,
1551         .read_pda = ezusb_read_pda,
1552         .program_init = ezusb_program_init,
1553         .program_end = ezusb_program_end,
1554         .program = ezusb_program,
1555         .lock_irqsave = ezusb_lock_irqsave,
1556         .unlock_irqrestore = ezusb_unlock_irqrestore,
1557         .lock_irq = ezusb_lock_irq,
1558         .unlock_irq = ezusb_unlock_irq,
1559 };
1560
1561 static const struct net_device_ops ezusb_netdev_ops = {
1562         .ndo_open               = orinoco_open,
1563         .ndo_stop               = orinoco_stop,
1564         .ndo_start_xmit         = ezusb_xmit,
1565         .ndo_set_multicast_list = orinoco_set_multicast_list,
1566         .ndo_change_mtu         = orinoco_change_mtu,
1567         .ndo_set_mac_address    = eth_mac_addr,
1568         .ndo_validate_addr      = eth_validate_addr,
1569         .ndo_tx_timeout         = orinoco_tx_timeout,
1570         .ndo_get_stats          = orinoco_get_stats,
1571 };
1572
1573 static int ezusb_probe(struct usb_interface *interface,
1574                        const struct usb_device_id *id)
1575 {
1576         struct usb_device *udev = interface_to_usbdev(interface);
1577         struct orinoco_private *priv;
1578         hermes_t *hw;
1579         struct ezusb_priv *upriv = NULL;
1580         struct usb_interface_descriptor *iface_desc;
1581         struct usb_endpoint_descriptor *ep;
1582         const struct firmware *fw_entry;
1583         int retval = 0;
1584         int i;
1585
1586         priv = alloc_orinocodev(sizeof(*upriv), &udev->dev,
1587                                 ezusb_hard_reset, NULL);
1588         if (!priv) {
1589                 err("Couldn't allocate orinocodev");
1590                 goto exit;
1591         }
1592
1593         hw = &priv->hw;
1594
1595         upriv = priv->card;
1596
1597         mutex_init(&upriv->mtx);
1598         spin_lock_init(&upriv->reply_count_lock);
1599
1600         spin_lock_init(&upriv->req_lock);
1601         INIT_LIST_HEAD(&upriv->req_pending);
1602         INIT_LIST_HEAD(&upriv->req_active);
1603
1604         upriv->udev = udev;
1605
1606         hw->iobase = (void __force __iomem *) &upriv->hermes_reg_fake;
1607         hw->reg_spacing = HERMES_16BIT_REGSPACING;
1608         hw->priv = upriv;
1609         hw->ops = &ezusb_ops;
1610
1611         /* set up the endpoint information */
1612         /* check out the endpoints */
1613
1614         iface_desc = &interface->altsetting[0].desc;
1615         for (i = 0; i < iface_desc->bNumEndpoints; ++i) {
1616                 ep = &interface->altsetting[0].endpoint[i].desc;
1617
1618                 if (((ep->bEndpointAddress & USB_ENDPOINT_DIR_MASK)
1619                      == USB_DIR_IN) &&
1620                     ((ep->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)
1621                      == USB_ENDPOINT_XFER_BULK)) {
1622                         /* we found a bulk in endpoint */
1623                         if (upriv->read_urb != NULL) {
1624                                 pr_warning("Found a second bulk in ep, ignored");
1625                                 continue;
1626                         }
1627
1628                         upriv->read_urb = usb_alloc_urb(0, GFP_KERNEL);
1629                         if (!upriv->read_urb) {
1630                                 err("No free urbs available");
1631                                 goto error;
1632                         }
1633                         if (le16_to_cpu(ep->wMaxPacketSize) != 64)
1634                                 pr_warning("bulk in: wMaxPacketSize!= 64");
1635                         if (ep->bEndpointAddress != (2 | USB_DIR_IN))
1636                                 pr_warning("bulk in: bEndpointAddress: %d",
1637                                      ep->bEndpointAddress);
1638                         upriv->read_pipe = usb_rcvbulkpipe(udev,
1639                                                          ep->
1640                                                          bEndpointAddress);
1641                         upriv->read_urb->transfer_buffer =
1642                             kmalloc(BULK_BUF_SIZE, GFP_KERNEL);
1643                         if (!upriv->read_urb->transfer_buffer) {
1644                                 err("Couldn't allocate IN buffer");
1645                                 goto error;
1646                         }
1647                 }
1648
1649                 if (((ep->bEndpointAddress & USB_ENDPOINT_DIR_MASK)
1650                      == USB_DIR_OUT) &&
1651                     ((ep->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)
1652                      == USB_ENDPOINT_XFER_BULK)) {
1653                         /* we found a bulk out endpoint */
1654                         if (upriv->bap_buf != NULL) {
1655                                 pr_warning("Found a second bulk out ep, ignored");
1656                                 continue;
1657                         }
1658
1659                         if (le16_to_cpu(ep->wMaxPacketSize) != 64)
1660                                 pr_warning("bulk out: wMaxPacketSize != 64");
1661                         if (ep->bEndpointAddress != 2)
1662                                 pr_warning("bulk out: bEndpointAddress: %d",
1663                                      ep->bEndpointAddress);
1664                         upriv->write_pipe = usb_sndbulkpipe(udev,
1665                                                           ep->
1666                                                           bEndpointAddress);
1667                         upriv->bap_buf = kmalloc(BULK_BUF_SIZE, GFP_KERNEL);
1668                         if (!upriv->bap_buf) {
1669                                 err("Couldn't allocate bulk_out_buffer");
1670                                 goto error;
1671                         }
1672                 }
1673         }
1674         if (!upriv->bap_buf || !upriv->read_urb) {
1675                 err("Didn't find the required bulk endpoints");
1676                 goto error;
1677         }
1678
1679         if (request_firmware(&fw_entry, "orinoco_ezusb_fw",
1680                              &interface->dev) == 0) {
1681                 firmware.size = fw_entry->size;
1682                 firmware.code = fw_entry->data;
1683         }
1684         if (firmware.size && firmware.code) {
1685                 ezusb_firmware_download(upriv, &firmware);
1686         } else {
1687                 err("No firmware to download");
1688                 goto error;
1689         }
1690
1691         if (ezusb_hard_reset(priv) < 0) {
1692                 err("Cannot reset the device");
1693                 goto error;
1694         }
1695
1696         /* If the firmware is already downloaded orinoco.c will call
1697          * ezusb_init but if the firmware is not already there, that will make
1698          * the kernel very unstable, so we try initializing here and quit in
1699          * case of error */
1700         if (ezusb_init(hw) < 0) {
1701                 err("Couldn't initialize the device");
1702                 err("Firmware may not be downloaded or may be wrong.");
1703                 goto error;
1704         }
1705
1706         /* Initialise the main driver */
1707         if (orinoco_init(priv) != 0) {
1708                 err("orinoco_init() failed\n");
1709                 goto error;
1710         }
1711
1712         if (orinoco_if_add(priv, 0, 0, &ezusb_netdev_ops) != 0) {
1713                 upriv->dev = NULL;
1714                 err("%s: orinoco_if_add() failed", __func__);
1715                 goto error;
1716         }
1717         upriv->dev = priv->ndev;
1718
1719         goto exit;
1720
1721  error:
1722         ezusb_delete(upriv);
1723         if (upriv->dev) {
1724                 /* upriv->dev was 0, so ezusb_delete() didn't free it */
1725                 free_orinocodev(priv);
1726         }
1727         upriv = NULL;
1728         retval = -EFAULT;
1729  exit:
1730         if (fw_entry) {
1731                 firmware.code = NULL;
1732                 firmware.size = 0;
1733                 release_firmware(fw_entry);
1734         }
1735         usb_set_intfdata(interface, upriv);
1736         return retval;
1737 }
1738
1739
1740 static void ezusb_disconnect(struct usb_interface *intf)
1741 {
1742         struct ezusb_priv *upriv = usb_get_intfdata(intf);
1743         usb_set_intfdata(intf, NULL);
1744         ezusb_delete(upriv);
1745         printk(KERN_INFO PFX "Disconnected\n");
1746 }
1747
1748
1749 /* usb specific object needed to register this driver with the usb subsystem */
1750 static struct usb_driver orinoco_driver = {
1751         .name = DRIVER_NAME,
1752         .probe = ezusb_probe,
1753         .disconnect = ezusb_disconnect,
1754         .id_table = ezusb_table,
1755 };
1756
1757 /* Can't be declared "const" or the whole __initdata section will
1758  * become const */
1759 static char version[] __initdata = DRIVER_NAME " " DRIVER_VERSION
1760     " (Manuel Estrada Sainz)";
1761
1762 static int __init ezusb_module_init(void)
1763 {
1764         int err;
1765
1766         printk(KERN_DEBUG "%s\n", version);
1767
1768         /* register this driver with the USB subsystem */
1769         err = usb_register(&orinoco_driver);
1770         if (err < 0) {
1771                 printk(KERN_ERR PFX "usb_register failed, error %d\n",
1772                        err);
1773                 return err;
1774         }
1775
1776         return 0;
1777 }
1778
1779 static void __exit ezusb_module_exit(void)
1780 {
1781         /* deregister this driver with the USB subsystem */
1782         usb_deregister(&orinoco_driver);
1783 }
1784
1785
1786 module_init(ezusb_module_init);
1787 module_exit(ezusb_module_exit);
1788
1789 MODULE_AUTHOR("Manuel Estrada Sainz");
1790 MODULE_DESCRIPTION
1791     ("Driver for Orinoco wireless LAN cards using EZUSB bridge");
1792 MODULE_LICENSE("Dual MPL/GPL");