drivers/net/wan/hostess_sv11.c

   1 /*
   2  *      Comtrol SV11 card driver
   3  *
   4  *      This is a slightly odd Z85230 synchronous driver. All you need to
   5  *      know basically is
   6  *
   7  *      Its a genuine Z85230
   8  *
   9  *      It supports DMA using two DMA channels in SYNC mode. The driver doesn't
  10  *      use these facilities
  11  *
  12  *      The control port is at io+1, the data at io+3 and turning off the DMA
  13  *      is done by writing 0 to io+4
  14  *
  15  *      The hardware does the bus handling to avoid the need for delays between
  16  *      touching control registers.
  17  *
  18  *      Port B isnt wired (why - beats me)
  19  */
  20
  21 #include <linux/module.h>
  22 #include <linux/kernel.h>
  23 #include <linux/mm.h>
  24 #include <linux/net.h>
  25 #include <linux/skbuff.h>
  26 #include <linux/netdevice.h>
  27 #include <linux/if_arp.h>
  28 #include <linux/delay.h>
  29 #include <linux/ioport.h>
  30 #include <net/arp.h>
  31
  32 #include <asm/io.h>
  33 #include <asm/dma.h>
  34 #include <asm/byteorder.h>
  35 #include <net/syncppp.h>
  36 #include "z85230.h"
  37
  38 static int dma;
  39
  40 struct sv11_device
  41 {
  42         void *if_ptr;   /* General purpose pointer (used by SPPP) */
  43         struct z8530_dev sync;
  44         struct ppp_device netdev;
  45 };
  46
  47 /*
  48  *      Network driver support routines
  49  */
  50
  51 /*
  52  *      Frame receive. Simple for our card as we do sync ppp and there
  53  *      is no funny garbage involved
  54  */
  55
  56 static void hostess_input(struct z8530_channel *c, struct sk_buff *skb)
  57 {
  58         /* Drop the CRC - it's not a good idea to try and negotiate it ;) */
  59         skb_trim(skb, skb->len-2);
  60         skb->protocol=__constant_htons(ETH_P_WAN_PPP);
  61         skb->mac.raw=skb->data;
  62         skb->dev=c->netdevice;
  63         /*
  64          *      Send it to the PPP layer. We don't have time to process
  65          *      it right now.
  66          */
  67         netif_rx(skb);
  68         c->netdevice->last_rx = jiffies;
  69 }
  70
  71 /*
  72  *      We've been placed in the UP state
  73  */
  74
  75 static int hostess_open(struct net_device *d)
  76 {
  77         struct sv11_device *sv11=d->priv;
  78         int err = -1;
  79
  80         /*
  81          *      Link layer up
  82          */
  83         switch(dma)
  84         {
  85                 case 0:
  86                         err=z8530_sync_open(d, &sv11->sync.chanA);
  87                         break;
  88                 case 1:
  89                         err=z8530_sync_dma_open(d, &sv11->sync.chanA);
  90                         break;
  91                 case 2:
  92                         err=z8530_sync_txdma_open(d, &sv11->sync.chanA);
  93                         break;
  94         }
  95
  96         if(err)
  97                 return err;
  98         /*
  99          *      Begin PPP
 100          */
 101         err=sppp_open(d);
 102         if(err)
 103         {
 104                 switch(dma)
 105                 {
 106                         case 0:
 107                                 z8530_sync_close(d, &sv11->sync.chanA);
 108                                 break;
 109                         case 1:
 110                                 z8530_sync_dma_close(d, &sv11->sync.chanA);
 111                                 break;
 112                         case 2:
 113                                 z8530_sync_txdma_close(d, &sv11->sync.chanA);
 114                                 break;
 115                 }
 116                 return err;
 117         }
 118         sv11->sync.chanA.rx_function=hostess_input;
 119
 120         /*
 121          *      Go go go
 122          */
 123
 124         netif_start_queue(d);
 125         return 0;
 126 }
 127
 128 static int hostess_close(struct net_device *d)
 129 {
 130         struct sv11_device *sv11=d->priv;
 131         /*
 132          *      Discard new frames
 133          */
 134         sv11->sync.chanA.rx_function=z8530_null_rx;
 135         /*
 136          *      PPP off
 137          */
 138         sppp_close(d);
 139         /*
 140          *      Link layer down
 141          */
 142         netif_stop_queue(d);
 143
 144         switch(dma)
 145         {
 146                 case 0:
 147                         z8530_sync_close(d, &sv11->sync.chanA);
 148                         break;
 149                 case 1:
 150                         z8530_sync_dma_close(d, &sv11->sync.chanA);
 151                         break;
 152                 case 2:
 153                         z8530_sync_txdma_close(d, &sv11->sync.chanA);
 154                         break;
 155         }
 156         return 0;
 157 }
 158
 159 static int hostess_ioctl(struct net_device *d, struct ifreq *ifr, int cmd)
 160 {
 161         /* struct sv11_device *sv11=d->priv;
 162            z8530_ioctl(d,&sv11->sync.chanA,ifr,cmd) */
 163         return sppp_do_ioctl(d, ifr,cmd);
 164 }
 165
 166 static struct net_device_stats *hostess_get_stats(struct net_device *d)
 167 {
 168         struct sv11_device *sv11=d->priv;
 169         if(sv11)
 170                 return z8530_get_stats(&sv11->sync.chanA);
 171         else
 172                 return NULL;
 173 }
 174
 175 /*
 176  *      Passed PPP frames, fire them downwind.
 177  */
 178
 179 static int hostess_queue_xmit(struct sk_buff *skb, struct net_device *d)
 180 {
 181         struct sv11_device *sv11=d->priv;
 182         return z8530_queue_xmit(&sv11->sync.chanA, skb);
 183 }
 184
 185 static int hostess_neigh_setup(struct neighbour *n)
 186 {
 187         if (n->nud_state == NUD_NONE) {
 188                 n->ops = &arp_broken_ops;
 189                 n->output = n->ops->output;
 190         }
 191         return 0;
 192 }
 193
 194 static int hostess_neigh_setup_dev(struct net_device *dev, struct neigh_parms *p)
 195 {
 196         if (p->tbl->family == AF_INET) {
 197                 p->neigh_setup = hostess_neigh_setup;
 198                 p->ucast_probes = 0;
 199                 p->mcast_probes = 0;
 200         }
 201         return 0;
 202 }
 203
 204 static void sv11_setup(struct net_device *dev)
 205 {
 206         dev->open = hostess_open;
 207         dev->stop = hostess_close;
 208         dev->hard_start_xmit = hostess_queue_xmit;
 209         dev->get_stats = hostess_get_stats;
 210         dev->do_ioctl = hostess_ioctl;
 211         dev->neigh_setup = hostess_neigh_setup_dev;
 212 }
 213
 214 /*
 215  *      Description block for a Comtrol Hostess SV11 card
 216  */
 217
 218 static struct sv11_device *sv11_init(int iobase, int irq)
 219 {
 220         struct z8530_dev *dev;
 221         struct sv11_device *sv;
 222
 223         /*
 224          *      Get the needed I/O space
 225          */
 226
 227         if(!request_region(iobase, 8, "Comtrol SV11"))
 228         {
 229                 printk(KERN_WARNING "hostess: I/O 0x%X already in use.\n", iobase);
 230                 return NULL;
 231         }
 232
 233         sv=(struct sv11_device *)kmalloc(sizeof(struct sv11_device), GFP_KERNEL);
 234         if(!sv)
 235                 goto fail3;
 236
 237         memset(sv, 0, sizeof(*sv));
 238         sv->if_ptr=&sv->netdev;
 239
 240         sv->netdev.dev = alloc_netdev(0, "hdlc%d", sv11_setup);
 241         if(!sv->netdev.dev)
 242                 goto fail2;
 243
 244         SET_MODULE_OWNER(sv->netdev.dev);
 245
 246         dev=&sv->sync;
 247
 248         /*
 249          *      Stuff in the I/O addressing
 250          */
 251
 252         dev->active = 0;
 253
 254         dev->chanA.ctrlio=iobase+1;
 255         dev->chanA.dataio=iobase+3;
 256         dev->chanB.ctrlio=-1;
 257         dev->chanB.dataio=-1;
 258         dev->chanA.irqs=&z8530_nop;
 259         dev->chanB.irqs=&z8530_nop;
 260
 261         outb(0, iobase+4);              /* DMA off */
 262
 263         /* We want a fast IRQ for this device. Actually we'd like an even faster
 264            IRQ ;) - This is one driver RtLinux is made for */
 265
 266         if(request_irq(irq, &z8530_interrupt, SA_INTERRUPT, "Hostess SV11", dev)<0)
 267         {
 268                 printk(KERN_WARNING "hostess: IRQ %d already in use.\n", irq);
 269                 goto fail1;
 270         }
 271
 272         dev->irq=irq;
 273         dev->chanA.private=sv;
 274         dev->chanA.netdevice=sv->netdev.dev;
 275         dev->chanA.dev=dev;
 276         dev->chanB.dev=dev;
 277
 278         if(dma)
 279         {
 280                 /*
 281                  *      You can have DMA off or 1 and 3 thats the lot
 282                  *      on the Comtrol.
 283                  */
 284                 dev->chanA.txdma=3;
 285                 dev->chanA.rxdma=1;
 286                 outb(0x03|0x08, iobase+4);              /* DMA on */
 287                 if(request_dma(dev->chanA.txdma, "Hostess SV/11 (TX)")!=0)
 288                         goto fail;
 289
 290                 if(dma==1)
 291                 {
 292                         if(request_dma(dev->chanA.rxdma, "Hostess SV/11 (RX)")!=0)
 293                                 goto dmafail;
 294                 }
 295         }
 296
 297         /* Kill our private IRQ line the hostess can end up chattering
 298            until the configuration is set */
 299         disable_irq(irq);
 300
 301         /*
 302          *      Begin normal initialise
 303          */
 304
 305         if(z8530_init(dev)!=0)
 306         {
 307                 printk(KERN_ERR "Z8530 series device not found.\n");
 308                 enable_irq(irq);
 309                 goto dmafail2;
 310         }
 311         z8530_channel_load(&dev->chanB, z8530_dead_port);
 312         if(dev->type==Z85C30)
 313                 z8530_channel_load(&dev->chanA, z8530_hdlc_kilostream);
 314         else
 315                 z8530_channel_load(&dev->chanA, z8530_hdlc_kilostream_85230);
 316
 317         enable_irq(irq);
 318
 319
 320         /*
 321          *      Now we can take the IRQ
 322          */
 323         if(dev_alloc_name(dev->chanA.netdevice,"hdlc%d")>=0)
 324         {
 325                 struct net_device *d=dev->chanA.netdevice;
 326
 327                 /*
 328                  *      Initialise the PPP components
 329                  */
 330                 sppp_attach(&sv->netdev);
 331
 332                 /*
 333                  *      Local fields
 334                  */
 335
 336                 d->base_addr = iobase;
 337                 d->irq = irq;
 338                 d->priv = sv;
 339
 340                 if(register_netdev(d))
 341                 {
 342                         printk(KERN_ERR "%s: unable to register device.\n",
 343                                 d->name);
 344                         sppp_detach(d);
 345                         goto dmafail2;
 346                 }
 347
 348                 z8530_describe(dev, "I/O", iobase);
 349                 dev->active=1;
 350                 return sv;
 351         }
 352 dmafail2:
 353         if(dma==1)
 354                 free_dma(dev->chanA.rxdma);
 355 dmafail:
 356         if(dma)
 357                 free_dma(dev->chanA.txdma);
 358 fail:
 359         free_irq(irq, dev);
 360 fail1:
 361         free_netdev(sv->netdev.dev);
 362 fail2:
 363         kfree(sv);
 364 fail3:
 365         release_region(iobase,8);
 366         return NULL;
 367 }
 368
 369 static void sv11_shutdown(struct sv11_device *dev)
 370 {
 371         sppp_detach(dev->netdev.dev);
 372         unregister_netdev(dev->netdev.dev);
 373         z8530_shutdown(&dev->sync);
 374         free_irq(dev->sync.irq, dev);
 375         if(dma)
 376         {
 377                 if(dma==1)
 378                         free_dma(dev->sync.chanA.rxdma);
 379                 free_dma(dev->sync.chanA.txdma);
 380         }
 381         release_region(dev->sync.chanA.ctrlio-1, 8);
 382         free_netdev(dev->netdev.dev);
 383         kfree(dev);
 384 }
 385
 386 #ifdef MODULE
 387
 388 static int io=0x200;
 389 static int irq=9;
 390
 391 module_param(io, int, 0);
 392 MODULE_PARM_DESC(io, "The I/O base of the Comtrol Hostess SV11 card");
 393 module_param(dma, int, 0);
 394 MODULE_PARM_DESC(dma, "Set this to 1 to use DMA1/DMA3 for TX/RX");
 395 module_param(irq, int, 0);
 396 MODULE_PARM_DESC(irq, "The interrupt line setting for the Comtrol Hostess SV11 card");
 397
 398 MODULE_AUTHOR("Alan Cox");
 399 MODULE_LICENSE("GPL");
 400 MODULE_DESCRIPTION("Modular driver for the Comtrol Hostess SV11");
 401
 402 static struct sv11_device *sv11_unit;
 403
 404 int init_module(void)
 405 {
 406         printk(KERN_INFO "SV-11 Z85230 Synchronous Driver v 0.03.\n");
 407         printk(KERN_INFO "(c) Copyright 2001, Red Hat Inc.\n");
 408         if((sv11_unit=sv11_init(io,irq))==NULL)
 409                 return -ENODEV;
 410         return 0;
 411 }
 412
 413 void cleanup_module(void)
 414 {
 415         if(sv11_unit)
 416                 sv11_shutdown(sv11_unit);
 417 }
 418
 419 #endif
 420