drivers/net/gianfar.c

   1 /*
   2  * drivers/net/gianfar.c
   3  *
   4  * Gianfar Ethernet Driver
   5  * This driver is designed for the non-CPM ethernet controllers
   6  * on the 85xx and 83xx family of integrated processors
   7  * Based on 8260_io/fcc_enet.c
   8  *
   9  * Author: Andy Fleming
  10  * Maintainer: Kumar Gala
  11  *
  12  * Copyright (c) 2002-2006 Freescale Semiconductor, Inc.
  13  * Copyright (c) 2007 MontaVista Software, Inc.
  14  *
  15  * This program is free software; you can redistribute  it and/or modify it
  16  * under  the terms of  the GNU General  Public License as published by the
  17  * Free Software Foundation;  either version 2 of the  License, or (at your
  18  * option) any later version.
  19  *
  20  *  Gianfar:  AKA Lambda Draconis, "Dragon"
  21  *  RA 11 31 24.2
  22  *  Dec +69 19 52
  23  *  V 3.84
  24  *  B-V +1.62
  25  *
  26  *  Theory of operation
  27  *
  28  *  The driver is initialized through of_device. Configuration information
  29  *  is therefore conveyed through an OF-style device tree.
  30  *
  31  *  The Gianfar Ethernet Controller uses a ring of buffer
  32  *  descriptors.  The beginning is indicated by a register
  33  *  pointing to the physical address of the start of the ring.
  34  *  The end is determined by a "wrap" bit being set in the
  35  *  last descriptor of the ring.
  36  *
  37  *  When a packet is received, the RXF bit in the
  38  *  IEVENT register is set, triggering an interrupt when the
  39  *  corresponding bit in the IMASK register is also set (if
  40  *  interrupt coalescing is active, then the interrupt may not
  41  *  happen immediately, but will wait until either a set number
  42  *  of frames or amount of time have passed).  In NAPI, the
  43  *  interrupt handler will signal there is work to be done, and
  44  *  exit. This method will start at the last known empty
  45  *  descriptor, and process every subsequent descriptor until there
  46  *  are none left with data (NAPI will stop after a set number of
  47  *  packets to give time to other tasks, but will eventually
  48  *  process all the packets).  The data arrives inside a
  49  *  pre-allocated skb, and so after the skb is passed up to the
  50  *  stack, a new skb must be allocated, and the address field in
  51  *  the buffer descriptor must be updated to indicate this new
  52  *  skb.
  53  *
  54  *  When the kernel requests that a packet be transmitted, the
  55  *  driver starts where it left off last time, and points the
  56  *  descriptor at the buffer which was passed in.  The driver
  57  *  then informs the DMA engine that there are packets ready to
  58  *  be transmitted.  Once the controller is finished transmitting
  59  *  the packet, an interrupt may be triggered (under the same
  60  *  conditions as for reception, but depending on the TXF bit).
  61  *  The driver then cleans up the buffer.
  62  */
  63
  64 #include <linux/kernel.h>
  65 #include <linux/string.h>
  66 #include <linux/errno.h>
  67 #include <linux/unistd.h>
  68 #include <linux/slab.h>
  69 #include <linux/interrupt.h>
  70 #include <linux/init.h>
  71 #include <linux/delay.h>
  72 #include <linux/netdevice.h>
  73 #include <linux/etherdevice.h>
  74 #include <linux/skbuff.h>
  75 #include <linux/if_vlan.h>
  76 #include <linux/spinlock.h>
  77 #include <linux/mm.h>
  78 #include <linux/of_platform.h>
  79 #include <linux/ip.h>
  80 #include <linux/tcp.h>
  81 #include <linux/udp.h>
  82 #include <linux/in.h>
  83
  84 #include <asm/io.h>
  85 #include <asm/irq.h>
  86 #include <asm/uaccess.h>
  87 #include <linux/module.h>
  88 #include <linux/dma-mapping.h>
  89 #include <linux/crc32.h>
  90 #include <linux/mii.h>
  91 #include <linux/phy.h>
  92 #include <linux/phy_fixed.h>
  93 #include <linux/of.h>
  94
  95 #include "gianfar.h"
  96 #include "gianfar_mii.h"
  97
  98 #define TX_TIMEOUT      (1*HZ)
  99 #undef BRIEF_GFAR_ERRORS
 100 #undef VERBOSE_GFAR_ERRORS
 101
 102 const char gfar_driver_name[] = "Gianfar Ethernet";
 103 const char gfar_driver_version[] = "1.3";
 104
 105 static int gfar_enet_open(struct net_device *dev);
 106 static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev);
 107 static void gfar_reset_task(struct work_struct *work);
 108 static void gfar_timeout(struct net_device *dev);
 109 static int gfar_close(struct net_device *dev);
 110 struct sk_buff *gfar_new_skb(struct net_device *dev);
 111 static void gfar_new_rxbdp(struct net_device *dev, struct rxbd8 *bdp,
 112                 struct sk_buff *skb);
 113 static int gfar_set_mac_address(struct net_device *dev);
 114 static int gfar_change_mtu(struct net_device *dev, int new_mtu);
 115 static irqreturn_t gfar_error(int irq, void *dev_id);
 116 static irqreturn_t gfar_transmit(int irq, void *dev_id);
 117 static irqreturn_t gfar_interrupt(int irq, void *dev_id);
 118 static void adjust_link(struct net_device *dev);
 119 static void init_registers(struct net_device *dev);
 120 static int init_phy(struct net_device *dev);
 121 static int gfar_probe(struct of_device *ofdev,
 122                 const struct of_device_id *match);
 123 static int gfar_remove(struct of_device *ofdev);
 124 static void free_skb_resources(struct gfar_private *priv);
 125 static void gfar_set_multi(struct net_device *dev);
 126 static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr);
 127 static void gfar_configure_serdes(struct net_device *dev);
 128 static int gfar_poll(struct napi_struct *napi, int budget);
 129 #ifdef CONFIG_NET_POLL_CONTROLLER
 130 static void gfar_netpoll(struct net_device *dev);
 131 #endif
 132 int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit);
 133 static int gfar_clean_tx_ring(struct net_device *dev);
 134 static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb,
 135                               int amount_pull);
 136 static void gfar_vlan_rx_register(struct net_device *netdev,
 137                                 struct vlan_group *grp);
 138 void gfar_halt(struct net_device *dev);
 139 static void gfar_halt_nodisable(struct net_device *dev);
 140 void gfar_start(struct net_device *dev);
 141 static void gfar_clear_exact_match(struct net_device *dev);
 142 static void gfar_set_mac_for_addr(struct net_device *dev, int num, u8 *addr);
 143
 144 extern const struct ethtool_ops gfar_ethtool_ops;
 145
 146 MODULE_AUTHOR("Freescale Semiconductor, Inc");
 147 MODULE_DESCRIPTION("Gianfar Ethernet Driver");
 148 MODULE_LICENSE("GPL");
 149
 150 /* Returns 1 if incoming frames use an FCB */
 151 static inline int gfar_uses_fcb(struct gfar_private *priv)
 152 {
 153         return priv->vlgrp || priv->rx_csum_enable;
 154 }
 155
 156 static int gfar_of_init(struct net_device *dev)
 157 {
 158         struct device_node *phy, *mdio;
 159         const unsigned int *id;
 160         const char *model;
 161         const char *ctype;
 162         const void *mac_addr;
 163         const phandle *ph;
 164         u64 addr, size;
 165         int err = 0;
 166         struct gfar_private *priv = netdev_priv(dev);
 167         struct device_node *np = priv->node;
 168         char bus_name[MII_BUS_ID_SIZE];
 169
 170         if (!np || !of_device_is_available(np))
 171                 return -ENODEV;
 172
 173         /* get a pointer to the register memory */
 174         addr = of_translate_address(np, of_get_address(np, 0, &size, NULL));
 175         priv->regs = ioremap(addr, size);
 176
 177         if (priv->regs == NULL)
 178                 return -ENOMEM;
 179
 180         priv->interruptTransmit = irq_of_parse_and_map(np, 0);
 181
 182         model = of_get_property(np, "model", NULL);
 183
 184         /* If we aren't the FEC we have multiple interrupts */
 185         if (model && strcasecmp(model, "FEC")) {
 186                 priv->interruptReceive = irq_of_parse_and_map(np, 1);
 187
 188                 priv->interruptError = irq_of_parse_and_map(np, 2);
 189
 190                 if (priv->interruptTransmit < 0 ||
 191                                 priv->interruptReceive < 0 ||
 192                                 priv->interruptError < 0) {
 193                         err = -EINVAL;
 194                         goto err_out;
 195                 }
 196         }
 197
 198         mac_addr = of_get_mac_address(np);
 199         if (mac_addr)
 200                 memcpy(dev->dev_addr, mac_addr, MAC_ADDR_LEN);
 201
 202         if (model && !strcasecmp(model, "TSEC"))
 203                 priv->device_flags =
 204                         FSL_GIANFAR_DEV_HAS_GIGABIT |
 205                         FSL_GIANFAR_DEV_HAS_COALESCE |
 206                         FSL_GIANFAR_DEV_HAS_RMON |
 207                         FSL_GIANFAR_DEV_HAS_MULTI_INTR;
 208         if (model && !strcasecmp(model, "eTSEC"))
 209                 priv->device_flags =
 210                         FSL_GIANFAR_DEV_HAS_GIGABIT |
 211                         FSL_GIANFAR_DEV_HAS_COALESCE |
 212                         FSL_GIANFAR_DEV_HAS_RMON |
 213                         FSL_GIANFAR_DEV_HAS_MULTI_INTR |
 214                         FSL_GIANFAR_DEV_HAS_PADDING |
 215                         FSL_GIANFAR_DEV_HAS_CSUM |
 216                         FSL_GIANFAR_DEV_HAS_VLAN |
 217                         FSL_GIANFAR_DEV_HAS_MAGIC_PACKET |
 218                         FSL_GIANFAR_DEV_HAS_EXTENDED_HASH;
 219
 220         ctype = of_get_property(np, "phy-connection-type", NULL);
 221
 222         /* We only care about rgmii-id.  The rest are autodetected */
 223         if (ctype && !strcmp(ctype, "rgmii-id"))
 224                 priv->interface = PHY_INTERFACE_MODE_RGMII_ID;
 225         else
 226                 priv->interface = PHY_INTERFACE_MODE_MII;
 227
 228         if (of_get_property(np, "fsl,magic-packet", NULL))
 229                 priv->device_flags |= FSL_GIANFAR_DEV_HAS_MAGIC_PACKET;
 230
 231         ph = of_get_property(np, "phy-handle", NULL);
 232         if (ph == NULL) {
 233                 u32 *fixed_link;
 234
 235                 fixed_link = (u32 *)of_get_property(np, "fixed-link", NULL);
 236                 if (!fixed_link) {
 237                         err = -ENODEV;
 238                         goto err_out;
 239                 }
 240
 241                 snprintf(priv->phy_bus_id, sizeof(priv->phy_bus_id),
 242                                 PHY_ID_FMT, "0", fixed_link[0]);
 243         } else {
 244                 phy = of_find_node_by_phandle(*ph);
 245
 246                 if (phy == NULL) {
 247                         err = -ENODEV;
 248                         goto err_out;
 249                 }
 250
 251                 mdio = of_get_parent(phy);
 252
 253                 id = of_get_property(phy, "reg", NULL);
 254
 255                 of_node_put(phy);
 256                 of_node_put(mdio);
 257
 258                 gfar_mdio_bus_name(bus_name, mdio);
 259                 snprintf(priv->phy_bus_id, sizeof(priv->phy_bus_id), "%s:%02x",
 260                                 bus_name, *id);
 261         }
 262
 263         /* Find the TBI PHY.  If it's not there, we don't support SGMII */
 264         ph = of_get_property(np, "tbi-handle", NULL);
 265         if (ph) {
 266                 struct device_node *tbi = of_find_node_by_phandle(*ph);
 267                 struct of_device *ofdev;
 268                 struct mii_bus *bus;
 269
 270                 if (!tbi)
 271                         return 0;
 272
 273                 mdio = of_get_parent(tbi);
 274                 if (!mdio)
 275                         return 0;
 276
 277                 ofdev = of_find_device_by_node(mdio);
 278
 279                 of_node_put(mdio);
 280
 281                 id = of_get_property(tbi, "reg", NULL);
 282                 if (!id)
 283                         return 0;
 284
 285                 of_node_put(tbi);
 286
 287                 bus = dev_get_drvdata(&ofdev->dev);
 288
 289                 priv->tbiphy = bus->phy_map[*id];
 290         }
 291
 292         return 0;
 293
 294 err_out:
 295         iounmap(priv->regs);
 296         return err;
 297 }
 298
 299 /* Ioctl MII Interface */
 300 static int gfar_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
 301 {
 302         struct gfar_private *priv = netdev_priv(dev);
 303
 304         if (!netif_running(dev))
 305                 return -EINVAL;
 306
 307         if (!priv->phydev)
 308                 return -ENODEV;
 309
 310         return phy_mii_ioctl(priv->phydev, if_mii(rq), cmd);
 311 }
 312
 313 /* Set up the ethernet device structure, private data,
 314  * and anything else we need before we start */
 315 static int gfar_probe(struct of_device *ofdev,
 316                 const struct of_device_id *match)
 317 {
 318         u32 tempval;
 319         struct net_device *dev = NULL;
 320         struct gfar_private *priv = NULL;
 321         DECLARE_MAC_BUF(mac);
 322         int err = 0;
 323         int len_devname;
 324
 325         /* Create an ethernet device instance */
 326         dev = alloc_etherdev(sizeof (*priv));
 327
 328         if (NULL == dev)
 329                 return -ENOMEM;
 330
 331         priv = netdev_priv(dev);
 332         priv->dev = dev;
 333         priv->node = ofdev->node;
 334
 335         err = gfar_of_init(dev);
 336
 337         if (err)
 338                 goto regs_fail;
 339
 340         spin_lock_init(&priv->txlock);
 341         spin_lock_init(&priv->rxlock);
 342         spin_lock_init(&priv->bflock);
 343         INIT_WORK(&priv->reset_task, gfar_reset_task);
 344
 345         dev_set_drvdata(&ofdev->dev, priv);
 346
 347         /* Stop the DMA engine now, in case it was running before */
 348         /* (The firmware could have used it, and left it running). */
 349         gfar_halt(dev);
 350
 351         /* Reset MAC layer */
 352         gfar_write(&priv->regs->maccfg1, MACCFG1_SOFT_RESET);
 353
 354         /* We need to delay at least 3 TX clocks */
 355         udelay(2);
 356
 357         tempval = (MACCFG1_TX_FLOW | MACCFG1_RX_FLOW);
 358         gfar_write(&priv->regs->maccfg1, tempval);
 359
 360         /* Initialize MACCFG2. */
 361         gfar_write(&priv->regs->maccfg2, MACCFG2_INIT_SETTINGS);
 362
 363         /* Initialize ECNTRL */
 364         gfar_write(&priv->regs->ecntrl, ECNTRL_INIT_SETTINGS);
 365
 366         /* Set the dev->base_addr to the gfar reg region */
 367         dev->base_addr = (unsigned long) (priv->regs);
 368
 369         SET_NETDEV_DEV(dev, &ofdev->dev);
 370
 371         /* Fill in the dev structure */
 372         dev->open = gfar_enet_open;
 373         dev->hard_start_xmit = gfar_start_xmit;
 374         dev->tx_timeout = gfar_timeout;
 375         dev->watchdog_timeo = TX_TIMEOUT;
 376         netif_napi_add(dev, &priv->napi, gfar_poll, GFAR_DEV_WEIGHT);
 377 #ifdef CONFIG_NET_POLL_CONTROLLER
 378         dev->poll_controller = gfar_netpoll;
 379 #endif
 380         dev->stop = gfar_close;
 381         dev->change_mtu = gfar_change_mtu;
 382         dev->mtu = 1500;
 383         dev->set_multicast_list = gfar_set_multi;
 384
 385         dev->ethtool_ops = &gfar_ethtool_ops;
 386         dev->do_ioctl = gfar_ioctl;
 387
 388         if (priv->device_flags & FSL_GIANFAR_DEV_HAS_CSUM) {
 389                 priv->rx_csum_enable = 1;
 390                 dev->features |= NETIF_F_IP_CSUM | NETIF_F_SG | NETIF_F_HIGHDMA;
 391         } else
 392                 priv->rx_csum_enable = 0;
 393
 394         priv->vlgrp = NULL;
 395
 396         if (priv->device_flags & FSL_GIANFAR_DEV_HAS_VLAN) {
 397                 dev->vlan_rx_register = gfar_vlan_rx_register;
 398
 399                 dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
 400         }
 401
 402         if (priv->device_flags & FSL_GIANFAR_DEV_HAS_EXTENDED_HASH) {
 403                 priv->extended_hash = 1;
 404                 priv->hash_width = 9;
 405
 406                 priv->hash_regs[0] = &priv->regs->igaddr0;
 407                 priv->hash_regs[1] = &priv->regs->igaddr1;
 408                 priv->hash_regs[2] = &priv->regs->igaddr2;
 409                 priv->hash_regs[3] = &priv->regs->igaddr3;
 410                 priv->hash_regs[4] = &priv->regs->igaddr4;
 411                 priv->hash_regs[5] = &priv->regs->igaddr5;
 412                 priv->hash_regs[6] = &priv->regs->igaddr6;
 413                 priv->hash_regs[7] = &priv->regs->igaddr7;
 414                 priv->hash_regs[8] = &priv->regs->gaddr0;
 415                 priv->hash_regs[9] = &priv->regs->gaddr1;
 416                 priv->hash_regs[10] = &priv->regs->gaddr2;
 417                 priv->hash_regs[11] = &priv->regs->gaddr3;
 418                 priv->hash_regs[12] = &priv->regs->gaddr4;
 419                 priv->hash_regs[13] = &priv->regs->gaddr5;
 420                 priv->hash_regs[14] = &priv->regs->gaddr6;
 421                 priv->hash_regs[15] = &priv->regs->gaddr7;
 422
 423         } else {
 424                 priv->extended_hash = 0;
 425                 priv->hash_width = 8;
 426
 427                 priv->hash_regs[0] = &priv->regs->gaddr0;
 428                 priv->hash_regs[1] = &priv->regs->gaddr1;
 429                 priv->hash_regs[2] = &priv->regs->gaddr2;
 430                 priv->hash_regs[3] = &priv->regs->gaddr3;
 431                 priv->hash_regs[4] = &priv->regs->gaddr4;
 432                 priv->hash_regs[5] = &priv->regs->gaddr5;
 433                 priv->hash_regs[6] = &priv->regs->gaddr6;
 434                 priv->hash_regs[7] = &priv->regs->gaddr7;
 435         }
 436
 437         if (priv->device_flags & FSL_GIANFAR_DEV_HAS_PADDING)
 438                 priv->padding = DEFAULT_PADDING;
 439         else
 440                 priv->padding = 0;
 441
 442         if (dev->features & NETIF_F_IP_CSUM)
 443                 dev->hard_header_len += GMAC_FCB_LEN;
 444
 445         priv->rx_buffer_size = DEFAULT_RX_BUFFER_SIZE;
 446         priv->tx_ring_size = DEFAULT_TX_RING_SIZE;
 447         priv->rx_ring_size = DEFAULT_RX_RING_SIZE;
 448         priv->num_txbdfree = DEFAULT_TX_RING_SIZE;
 449
 450         priv->txcoalescing = DEFAULT_TX_COALESCE;
 451         priv->txic = DEFAULT_TXIC;
 452         priv->rxcoalescing = DEFAULT_RX_COALESCE;
 453         priv->rxic = DEFAULT_RXIC;
 454
 455         /* Enable most messages by default */
 456         priv->msg_enable = (NETIF_MSG_IFUP << 1 ) - 1;
 457
 458         /* Carrier starts down, phylib will bring it up */
 459         netif_carrier_off(dev);
 460
 461         err = register_netdev(dev);
 462
 463         if (err) {
 464                 printk(KERN_ERR "%s: Cannot register net device, aborting.\n",
 465                                 dev->name);
 466                 goto register_fail;
 467         }
 468
 469         /* fill out IRQ number and name fields */
 470         len_devname = strlen(dev->name);
 471         strncpy(&priv->int_name_tx[0], dev->name, len_devname);
 472         if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) {
 473                 strncpy(&priv->int_name_tx[len_devname],
 474                         "_tx", sizeof("_tx") + 1);
 475
 476                 strncpy(&priv->int_name_rx[0], dev->name, len_devname);
 477                 strncpy(&priv->int_name_rx[len_devname],
 478                         "_rx", sizeof("_rx") + 1);
 479
 480                 strncpy(&priv->int_name_er[0], dev->name, len_devname);
 481                 strncpy(&priv->int_name_er[len_devname],
 482                         "_er", sizeof("_er") + 1);
 483         } else
 484                 priv->int_name_tx[len_devname] = '\0';
 485
 486         /* Create all the sysfs files */
 487         gfar_init_sysfs(dev);
 488
 489         /* Print out the device info */
 490         printk(KERN_INFO DEVICE_NAME "%pM\n", dev->name, dev->dev_addr);
 491
 492         /* Even more device info helps when determining which kernel */
 493         /* provided which set of benchmarks. */
 494         printk(KERN_INFO "%s: Running with NAPI enabled\n", dev->name);
 495         printk(KERN_INFO "%s: %d/%d RX/TX BD ring size\n",
 496                dev->name, priv->rx_ring_size, priv->tx_ring_size);
 497
 498         return 0;
 499
 500 register_fail:
 501         iounmap(priv->regs);
 502 regs_fail:
 503         free_netdev(dev);
 504         return err;
 505 }
 506
 507 static int gfar_remove(struct of_device *ofdev)
 508 {
 509         struct gfar_private *priv = dev_get_drvdata(&ofdev->dev);
 510
 511         dev_set_drvdata(&ofdev->dev, NULL);
 512
 513         iounmap(priv->regs);
 514         free_netdev(priv->dev);
 515
 516         return 0;
 517 }
 518
 519 #ifdef CONFIG_PM
 520 static int gfar_suspend(struct of_device *ofdev, pm_message_t state)
 521 {
 522         struct gfar_private *priv = dev_get_drvdata(&ofdev->dev);
 523         struct net_device *dev = priv->dev;
 524         unsigned long flags;
 525         u32 tempval;
 526
 527         int magic_packet = priv->wol_en &&
 528                 (priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET);
 529
 530         netif_device_detach(dev);
 531
 532         if (netif_running(dev)) {
 533                 spin_lock_irqsave(&priv->txlock, flags);
 534                 spin_lock(&priv->rxlock);
 535
 536                 gfar_halt_nodisable(dev);
 537
 538                 /* Disable Tx, and Rx if wake-on-LAN is disabled. */
 539                 tempval = gfar_read(&priv->regs->maccfg1);
 540
 541                 tempval &= ~MACCFG1_TX_EN;
 542
 543                 if (!magic_packet)
 544                         tempval &= ~MACCFG1_RX_EN;
 545
 546                 gfar_write(&priv->regs->maccfg1, tempval);
 547
 548                 spin_unlock(&priv->rxlock);
 549                 spin_unlock_irqrestore(&priv->txlock, flags);
 550
 551                 napi_disable(&priv->napi);
 552
 553                 if (magic_packet) {
 554                         /* Enable interrupt on Magic Packet */
 555                         gfar_write(&priv->regs->imask, IMASK_MAG);
 556
 557                         /* Enable Magic Packet mode */
 558                         tempval = gfar_read(&priv->regs->maccfg2);
 559                         tempval |= MACCFG2_MPEN;
 560                         gfar_write(&priv->regs->maccfg2, tempval);
 561                 } else {
 562                         phy_stop(priv->phydev);
 563                 }
 564         }
 565
 566         return 0;
 567 }
 568
 569 static int gfar_resume(struct of_device *ofdev)
 570 {
 571         struct gfar_private *priv = dev_get_drvdata(&ofdev->dev);
 572         struct net_device *dev = priv->dev;
 573         unsigned long flags;
 574         u32 tempval;
 575         int magic_packet = priv->wol_en &&
 576                 (priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET);
 577
 578         if (!netif_running(dev)) {
 579                 netif_device_attach(dev);
 580                 return 0;
 581         }
 582
 583         if (!magic_packet && priv->phydev)
 584                 phy_start(priv->phydev);
 585
 586         /* Disable Magic Packet mode, in case something
 587          * else woke us up.
 588          */
 589
 590         spin_lock_irqsave(&priv->txlock, flags);
 591         spin_lock(&priv->rxlock);
 592
 593         tempval = gfar_read(&priv->regs->maccfg2);
 594         tempval &= ~MACCFG2_MPEN;
 595         gfar_write(&priv->regs->maccfg2, tempval);
 596
 597         gfar_start(dev);
 598
 599         spin_unlock(&priv->rxlock);
 600         spin_unlock_irqrestore(&priv->txlock, flags);
 601
 602         netif_device_attach(dev);
 603
 604         napi_enable(&priv->napi);
 605
 606         return 0;
 607 }
 608 #else
 609 #define gfar_suspend NULL
 610 #define gfar_resume NULL
 611 #endif
 612
 613 /* Reads the controller's registers to determine what interface
 614  * connects it to the PHY.
 615  */
 616 static phy_interface_t gfar_get_interface(struct net_device *dev)
 617 {
 618         struct gfar_private *priv = netdev_priv(dev);
 619         u32 ecntrl = gfar_read(&priv->regs->ecntrl);
 620
 621         if (ecntrl & ECNTRL_SGMII_MODE)
 622                 return PHY_INTERFACE_MODE_SGMII;
 623
 624         if (ecntrl & ECNTRL_TBI_MODE) {
 625                 if (ecntrl & ECNTRL_REDUCED_MODE)
 626                         return PHY_INTERFACE_MODE_RTBI;
 627                 else
 628                         return PHY_INTERFACE_MODE_TBI;
 629         }
 630
 631         if (ecntrl & ECNTRL_REDUCED_MODE) {
 632                 if (ecntrl & ECNTRL_REDUCED_MII_MODE)
 633                         return PHY_INTERFACE_MODE_RMII;
 634                 else {
 635                         phy_interface_t interface = priv->interface;
 636
 637                         /*
 638                          * This isn't autodetected right now, so it must
 639                          * be set by the device tree or platform code.
 640                          */
 641                         if (interface == PHY_INTERFACE_MODE_RGMII_ID)
 642                                 return PHY_INTERFACE_MODE_RGMII_ID;
 643
 644                         return PHY_INTERFACE_MODE_RGMII;
 645                 }
 646         }
 647
 648         if (priv->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT)
 649                 return PHY_INTERFACE_MODE_GMII;
 650
 651         return PHY_INTERFACE_MODE_MII;
 652 }
 653
 654
 655 /* Initializes driver's PHY state, and attaches to the PHY.
 656  * Returns 0 on success.
 657  */
 658 static int init_phy(struct net_device *dev)
 659 {
 660         struct gfar_private *priv = netdev_priv(dev);
 661         uint gigabit_support =
 662                 priv->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT ?
 663                 SUPPORTED_1000baseT_Full : 0;
 664         struct phy_device *phydev;
 665         phy_interface_t interface;
 666
 667         priv->oldlink = 0;
 668         priv->oldspeed = 0;
 669         priv->oldduplex = -1;
 670
 671         interface = gfar_get_interface(dev);
 672
 673         phydev = phy_connect(dev, priv->phy_bus_id, &adjust_link, 0, interface);
 674
 675         if (interface == PHY_INTERFACE_MODE_SGMII)
 676                 gfar_configure_serdes(dev);
 677
 678         if (IS_ERR(phydev)) {
 679                 printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
 680                 return PTR_ERR(phydev);
 681         }
 682
 683         /* Remove any features not supported by the controller */
 684         phydev->supported &= (GFAR_SUPPORTED | gigabit_support);
 685         phydev->advertising = phydev->supported;
 686
 687         priv->phydev = phydev;
 688
 689         return 0;
 690 }
 691
 692 /*
 693  * Initialize TBI PHY interface for communicating with the
 694  * SERDES lynx PHY on the chip.  We communicate with this PHY
 695  * through the MDIO bus on each controller, treating it as a
 696  * "normal" PHY at the address found in the TBIPA register.  We assume
 697  * that the TBIPA register is valid.  Either the MDIO bus code will set
 698  * it to a value that doesn't conflict with other PHYs on the bus, or the
 699  * value doesn't matter, as there are no other PHYs on the bus.
 700  */
 701 static void gfar_configure_serdes(struct net_device *dev)
 702 {
 703         struct gfar_private *priv = netdev_priv(dev);
 704
 705         if (!priv->tbiphy) {
 706                 printk(KERN_WARNING "SGMII mode requires that the device "
 707                                 "tree specify a tbi-handle\n");
 708                 return;
 709         }
 710
 711         /*
 712          * If the link is already up, we must already be ok, and don't need to
 713          * configure and reset the TBI<->SerDes link.  Maybe U-Boot configured
 714          * everything for us?  Resetting it takes the link down and requires
 715          * several seconds for it to come back.
 716          */
 717         if (phy_read(priv->tbiphy, MII_BMSR) & BMSR_LSTATUS)
 718                 return;
 719
 720         /* Single clk mode, mii mode off(for serdes communication) */
 721         phy_write(priv->tbiphy, MII_TBICON, TBICON_CLK_SELECT);
 722
 723         phy_write(priv->tbiphy, MII_ADVERTISE,
 724                         ADVERTISE_1000XFULL | ADVERTISE_1000XPAUSE |
 725                         ADVERTISE_1000XPSE_ASYM);
 726
 727         phy_write(priv->tbiphy, MII_BMCR, BMCR_ANENABLE |
 728                         BMCR_ANRESTART | BMCR_FULLDPLX | BMCR_SPEED1000);
 729 }
 730
 731 static void init_registers(struct net_device *dev)
 732 {
 733         struct gfar_private *priv = netdev_priv(dev);
 734
 735         /* Clear IEVENT */
 736         gfar_write(&priv->regs->ievent, IEVENT_INIT_CLEAR);
 737
 738         /* Initialize IMASK */
 739         gfar_write(&priv->regs->imask, IMASK_INIT_CLEAR);
 740
 741         /* Init hash registers to zero */
 742         gfar_write(&priv->regs->igaddr0, 0);
 743         gfar_write(&priv->regs->igaddr1, 0);
 744         gfar_write(&priv->regs->igaddr2, 0);
 745         gfar_write(&priv->regs->igaddr3, 0);
 746         gfar_write(&priv->regs->igaddr4, 0);
 747         gfar_write(&priv->regs->igaddr5, 0);
 748         gfar_write(&priv->regs->igaddr6, 0);
 749         gfar_write(&priv->regs->igaddr7, 0);
 750
 751         gfar_write(&priv->regs->gaddr0, 0);
 752         gfar_write(&priv->regs->gaddr1, 0);
 753         gfar_write(&priv->regs->gaddr2, 0);
 754         gfar_write(&priv->regs->gaddr3, 0);
 755         gfar_write(&priv->regs->gaddr4, 0);
 756         gfar_write(&priv->regs->gaddr5, 0);
 757         gfar_write(&priv->regs->gaddr6, 0);
 758         gfar_write(&priv->regs->gaddr7, 0);
 759
 760         /* Zero out the rmon mib registers if it has them */
 761         if (priv->device_flags & FSL_GIANFAR_DEV_HAS_RMON) {
 762                 memset_io(&(priv->regs->rmon), 0, sizeof (struct rmon_mib));
 763
 764                 /* Mask off the CAM interrupts */
 765                 gfar_write(&priv->regs->rmon.cam1, 0xffffffff);
 766                 gfar_write(&priv->regs->rmon.cam2, 0xffffffff);
 767         }
 768
 769         /* Initialize the max receive buffer length */
 770         gfar_write(&priv->regs->mrblr, priv->rx_buffer_size);
 771
 772         /* Initialize the Minimum Frame Length Register */
 773         gfar_write(&priv->regs->minflr, MINFLR_INIT_SETTINGS);
 774 }
 775
 776
 777 /* Halt the receive and transmit queues */
 778 static void gfar_halt_nodisable(struct net_device *dev)
 779 {
 780         struct gfar_private *priv = netdev_priv(dev);
 781         struct gfar __iomem *regs = priv->regs;
 782         u32 tempval;
 783
 784         /* Mask all interrupts */
 785         gfar_write(&regs->imask, IMASK_INIT_CLEAR);
 786
 787         /* Clear all interrupts */
 788         gfar_write(&regs->ievent, IEVENT_INIT_CLEAR);
 789
 790         /* Stop the DMA, and wait for it to stop */
 791         tempval = gfar_read(&priv->regs->dmactrl);
 792         if ((tempval & (DMACTRL_GRS | DMACTRL_GTS))
 793             != (DMACTRL_GRS | DMACTRL_GTS)) {
 794                 tempval |= (DMACTRL_GRS | DMACTRL_GTS);
 795                 gfar_write(&priv->regs->dmactrl, tempval);
 796
 797                 while (!(gfar_read(&priv->regs->ievent) &
 798                          (IEVENT_GRSC | IEVENT_GTSC)))
 799                         cpu_relax();
 800         }
 801 }
 802
 803 /* Halt the receive and transmit queues */
 804 void gfar_halt(struct net_device *dev)
 805 {
 806         struct gfar_private *priv = netdev_priv(dev);
 807         struct gfar __iomem *regs = priv->regs;
 808         u32 tempval;
 809
 810         gfar_halt_nodisable(dev);
 811
 812         /* Disable Rx and Tx */
 813         tempval = gfar_read(&regs->maccfg1);
 814         tempval &= ~(MACCFG1_RX_EN | MACCFG1_TX_EN);
 815         gfar_write(&regs->maccfg1, tempval);
 816 }
 817
 818 void stop_gfar(struct net_device *dev)
 819 {
 820         struct gfar_private *priv = netdev_priv(dev);
 821         struct gfar __iomem *regs = priv->regs;
 822         unsigned long flags;
 823
 824         phy_stop(priv->phydev);
 825
 826         /* Lock it down */
 827         spin_lock_irqsave(&priv->txlock, flags);
 828         spin_lock(&priv->rxlock);
 829
 830         gfar_halt(dev);
 831
 832         spin_unlock(&priv->rxlock);
 833         spin_unlock_irqrestore(&priv->txlock, flags);
 834
 835         /* Free the IRQs */
 836         if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) {
 837                 free_irq(priv->interruptError, dev);
 838                 free_irq(priv->interruptTransmit, dev);
 839                 free_irq(priv->interruptReceive, dev);
 840         } else {
 841                 free_irq(priv->interruptTransmit, dev);
 842         }
 843
 844         free_skb_resources(priv);
 845
 846         dma_free_coherent(&dev->dev,
 847                         sizeof(struct txbd8)*priv->tx_ring_size
 848                         + sizeof(struct rxbd8)*priv->rx_ring_size,
 849                         priv->tx_bd_base,
 850                         gfar_read(&regs->tbase0));
 851 }
 852
 853 /* If there are any tx skbs or rx skbs still around, free them.
 854  * Then free tx_skbuff and rx_skbuff */
 855 static void free_skb_resources(struct gfar_private *priv)
 856 {
 857         struct rxbd8 *rxbdp;
 858         struct txbd8 *txbdp;
 859         int i, j;
 860
 861         /* Go through all the buffer descriptors and free their data buffers */
 862         txbdp = priv->tx_bd_base;
 863
 864         for (i = 0; i < priv->tx_ring_size; i++) {
 865                 if (!priv->tx_skbuff[i])
 866                         continue;
 867
 868                 dma_unmap_single(&priv->dev->dev, txbdp->bufPtr,
 869                                 txbdp->length, DMA_TO_DEVICE);
 870                 txbdp->lstatus = 0;
 871                 for (j = 0; j < skb_shinfo(priv->tx_skbuff[i])->nr_frags; j++) {
 872                         txbdp++;
 873                         dma_unmap_page(&priv->dev->dev, txbdp->bufPtr,
 874                                         txbdp->length, DMA_TO_DEVICE);
 875                 }
 876                 txbdp++;
 877                 dev_kfree_skb_any(priv->tx_skbuff[i]);
 878                 priv->tx_skbuff[i] = NULL;
 879         }
 880
 881         kfree(priv->tx_skbuff);
 882
 883         rxbdp = priv->rx_bd_base;
 884
 885         /* rx_skbuff is not guaranteed to be allocated, so only
 886          * free it and its contents if it is allocated */
 887         if(priv->rx_skbuff != NULL) {
 888                 for (i = 0; i < priv->rx_ring_size; i++) {
 889                         if (priv->rx_skbuff[i]) {
 890                                 dma_unmap_single(&priv->dev->dev, rxbdp->bufPtr,
 891                                                 priv->rx_buffer_size,
 892                                                 DMA_FROM_DEVICE);
 893
 894                                 dev_kfree_skb_any(priv->rx_skbuff[i]);
 895                                 priv->rx_skbuff[i] = NULL;
 896                         }
 897
 898                         rxbdp->lstatus = 0;
 899                         rxbdp->bufPtr = 0;
 900
 901                         rxbdp++;
 902                 }
 903
 904                 kfree(priv->rx_skbuff);
 905         }
 906 }
 907
 908 void gfar_start(struct net_device *dev)
 909 {
 910         struct gfar_private *priv = netdev_priv(dev);
 911         struct gfar __iomem *regs = priv->regs;
 912         u32 tempval;
 913
 914         /* Enable Rx and Tx in MACCFG1 */
 915         tempval = gfar_read(&regs->maccfg1);
 916         tempval |= (MACCFG1_RX_EN | MACCFG1_TX_EN);
 917         gfar_write(&regs->maccfg1, tempval);
 918
 919         /* Initialize DMACTRL to have WWR and WOP */
 920         tempval = gfar_read(&priv->regs->dmactrl);
 921         tempval |= DMACTRL_INIT_SETTINGS;
 922         gfar_write(&priv->regs->dmactrl, tempval);
 923
 924         /* Make sure we aren't stopped */
 925         tempval = gfar_read(&priv->regs->dmactrl);
 926         tempval &= ~(DMACTRL_GRS | DMACTRL_GTS);
 927         gfar_write(&priv->regs->dmactrl, tempval);
 928
 929         /* Clear THLT/RHLT, so that the DMA starts polling now */
 930         gfar_write(&regs->tstat, TSTAT_CLEAR_THALT);
 931         gfar_write(&regs->rstat, RSTAT_CLEAR_RHALT);
 932
 933         /* Unmask the interrupts we look for */
 934         gfar_write(&regs->imask, IMASK_DEFAULT);
 935
 936         dev->trans_start = jiffies;
 937 }
 938
 939 /* Bring the controller up and running */
 940 int startup_gfar(struct net_device *dev)
 941 {
 942         struct txbd8 *txbdp;
 943         struct rxbd8 *rxbdp;
 944         dma_addr_t addr = 0;
 945         unsigned long vaddr;
 946         int i;
 947         struct gfar_private *priv = netdev_priv(dev);
 948         struct gfar __iomem *regs = priv->regs;
 949         int err = 0;
 950         u32 rctrl = 0;
 951         u32 attrs = 0;
 952
 953         gfar_write(&regs->imask, IMASK_INIT_CLEAR);
 954
 955         /* Allocate memory for the buffer descriptors */
 956         vaddr = (unsigned long) dma_alloc_coherent(&dev->dev,
 957                         sizeof (struct txbd8) * priv->tx_ring_size +
 958                         sizeof (struct rxbd8) * priv->rx_ring_size,
 959                         &addr, GFP_KERNEL);
 960
 961         if (vaddr == 0) {
 962                 if (netif_msg_ifup(priv))
 963                         printk(KERN_ERR "%s: Could not allocate buffer descriptors!\n",
 964                                         dev->name);
 965                 return -ENOMEM;
 966         }
 967
 968         priv->tx_bd_base = (struct txbd8 *) vaddr;
 969
 970         /* enet DMA only understands physical addresses */
 971         gfar_write(&regs->tbase0, addr);
 972
 973         /* Start the rx descriptor ring where the tx ring leaves off */
 974         addr = addr + sizeof (struct txbd8) * priv->tx_ring_size;
 975         vaddr = vaddr + sizeof (struct txbd8) * priv->tx_ring_size;
 976         priv->rx_bd_base = (struct rxbd8 *) vaddr;
 977         gfar_write(&regs->rbase0, addr);
 978
 979         /* Setup the skbuff rings */
 980         priv->tx_skbuff =
 981             (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) *
 982                                         priv->tx_ring_size, GFP_KERNEL);
 983
 984         if (NULL == priv->tx_skbuff) {
 985                 if (netif_msg_ifup(priv))
 986                         printk(KERN_ERR "%s: Could not allocate tx_skbuff\n",
 987                                         dev->name);
 988                 err = -ENOMEM;
 989                 goto tx_skb_fail;
 990         }
 991
 992         for (i = 0; i < priv->tx_ring_size; i++)
 993                 priv->tx_skbuff[i] = NULL;
 994
 995         priv->rx_skbuff =
 996             (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) *
 997                                         priv->rx_ring_size, GFP_KERNEL);
 998
 999         if (NULL == priv->rx_skbuff) {
1000                 if (netif_msg_ifup(priv))
1001                         printk(KERN_ERR "%s: Could not allocate rx_skbuff\n",
1002                                         dev->name);
1003                 err = -ENOMEM;
1004                 goto rx_skb_fail;
1005         }
1006
1007         for (i = 0; i < priv->rx_ring_size; i++)
1008                 priv->rx_skbuff[i] = NULL;
1009
1010         /* Initialize some variables in our dev structure */
1011         priv->num_txbdfree = priv->tx_ring_size;
1012         priv->dirty_tx = priv->cur_tx = priv->tx_bd_base;
1013         priv->cur_rx = priv->rx_bd_base;
1014         priv->skb_curtx = priv->skb_dirtytx = 0;
1015         priv->skb_currx = 0;
1016
1017         /* Initialize Transmit Descriptor Ring */
1018         txbdp = priv->tx_bd_base;
1019         for (i = 0; i < priv->tx_ring_size; i++) {
1020                 txbdp->lstatus = 0;
1021                 txbdp->bufPtr = 0;
1022                 txbdp++;
1023         }
1024
1025         /* Set the last descriptor in the ring to indicate wrap */
1026         txbdp--;
1027         txbdp->status |= TXBD_WRAP;
1028
1029         rxbdp = priv->rx_bd_base;
1030         for (i = 0; i < priv->rx_ring_size; i++) {
1031                 struct sk_buff *skb;
1032
1033                 skb = gfar_new_skb(dev);
1034
1035                 if (!skb) {
1036                         printk(KERN_ERR "%s: Can't allocate RX buffers\n",
1037                                         dev->name);
1038
1039                         goto err_rxalloc_fail;
1040                 }
1041
1042                 priv->rx_skbuff[i] = skb;
1043
1044                 gfar_new_rxbdp(dev, rxbdp, skb);
1045
1046                 rxbdp++;
1047         }
1048
1049         /* Set the last descriptor in the ring to wrap */
1050         rxbdp--;
1051         rxbdp->status |= RXBD_WRAP;
1052
1053         /* If the device has multiple interrupts, register for
1054          * them.  Otherwise, only register for the one */
1055         if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) {
1056                 /* Install our interrupt handlers for Error,
1057                  * Transmit, and Receive */
1058                 if (request_irq(priv->interruptError, gfar_error,
1059                                 0, priv->int_name_er, dev) < 0) {
1060                         if (netif_msg_intr(priv))
1061                                 printk(KERN_ERR "%s: Can't get IRQ %d\n",
1062                                         dev->name, priv->interruptError);
1063
1064                         err = -1;
1065                         goto err_irq_fail;
1066                 }
1067
1068                 if (request_irq(priv->interruptTransmit, gfar_transmit,
1069                                 0, priv->int_name_tx, dev) < 0) {
1070                         if (netif_msg_intr(priv))
1071                                 printk(KERN_ERR "%s: Can't get IRQ %d\n",
1072                                         dev->name, priv->interruptTransmit);
1073
1074                         err = -1;
1075
1076                         goto tx_irq_fail;
1077                 }
1078
1079                 if (request_irq(priv->interruptReceive, gfar_receive,
1080                                 0, priv->int_name_rx, dev) < 0) {
1081                         if (netif_msg_intr(priv))
1082                                 printk(KERN_ERR "%s: Can't get IRQ %d (receive0)\n",
1083                                                 dev->name, priv->interruptReceive);
1084
1085                         err = -1;
1086                         goto rx_irq_fail;
1087                 }
1088         } else {
1089                 if (request_irq(priv->interruptTransmit, gfar_interrupt,
1090                                 0, priv->int_name_tx, dev) < 0) {
1091                         if (netif_msg_intr(priv))
1092                                 printk(KERN_ERR "%s: Can't get IRQ %d\n",
1093                                         dev->name, priv->interruptTransmit);
1094
1095                         err = -1;
1096                         goto err_irq_fail;
1097                 }
1098         }
1099
1100         phy_start(priv->phydev);
1101
1102         /* Configure the coalescing support */
1103         gfar_write(&regs->txic, 0);
1104         if (priv->txcoalescing)
1105                 gfar_write(&regs->txic, priv->txic);
1106
1107         gfar_write(&regs->rxic, 0);
1108         if (priv->rxcoalescing)
1109                 gfar_write(&regs->rxic, priv->rxic);
1110
1111         if (priv->rx_csum_enable)
1112                 rctrl |= RCTRL_CHECKSUMMING;
1113
1114         if (priv->extended_hash) {
1115                 rctrl |= RCTRL_EXTHASH;
1116
1117                 gfar_clear_exact_match(dev);
1118                 rctrl |= RCTRL_EMEN;
1119         }
1120
1121         if (priv->padding) {
1122                 rctrl &= ~RCTRL_PAL_MASK;
1123                 rctrl |= RCTRL_PADDING(priv->padding);
1124         }
1125
1126         /* Init rctrl based on our settings */
1127         gfar_write(&priv->regs->rctrl, rctrl);
1128
1129         if (dev->features & NETIF_F_IP_CSUM)
1130                 gfar_write(&priv->regs->tctrl, TCTRL_INIT_CSUM);
1131
1132         /* Set the extraction length and index */
1133         attrs = ATTRELI_EL(priv->rx_stash_size) |
1134                 ATTRELI_EI(priv->rx_stash_index);
1135
1136         gfar_write(&priv->regs->attreli, attrs);
1137
1138         /* Start with defaults, and add stashing or locking
1139          * depending on the approprate variables */
1140         attrs = ATTR_INIT_SETTINGS;
1141
1142         if (priv->bd_stash_en)
1143                 attrs |= ATTR_BDSTASH;
1144
1145         if (priv->rx_stash_size != 0)
1146                 attrs |= ATTR_BUFSTASH;
1147
1148         gfar_write(&priv->regs->attr, attrs);
1149
1150         gfar_write(&priv->regs->fifo_tx_thr, priv->fifo_threshold);
1151         gfar_write(&priv->regs->fifo_tx_starve, priv->fifo_starve);
1152         gfar_write(&priv->regs->fifo_tx_starve_shutoff, priv->fifo_starve_off);
1153
1154         /* Start the controller */
1155         gfar_start(dev);
1156
1157         return 0;
1158
1159 rx_irq_fail:
1160         free_irq(priv->interruptTransmit, dev);
1161 tx_irq_fail:
1162         free_irq(priv->interruptError, dev);
1163 err_irq_fail:
1164 err_rxalloc_fail:
1165 rx_skb_fail:
1166         free_skb_resources(priv);
1167 tx_skb_fail:
1168         dma_free_coherent(&dev->dev,
1169                         sizeof(struct txbd8)*priv->tx_ring_size
1170                         + sizeof(struct rxbd8)*priv->rx_ring_size,
1171                         priv->tx_bd_base,
1172                         gfar_read(&regs->tbase0));
1173
1174         return err;
1175 }
1176
1177 /* Called when something needs to use the ethernet device */
1178 /* Returns 0 for success. */
1179 static int gfar_enet_open(struct net_device *dev)
1180 {
1181         struct gfar_private *priv = netdev_priv(dev);
1182         int err;
1183
1184         napi_enable(&priv->napi);
1185
1186         /* Initialize a bunch of registers */
1187         init_registers(dev);
1188
1189         gfar_set_mac_address(dev);
1190
1191         err = init_phy(dev);
1192
1193         if(err) {
1194                 napi_disable(&priv->napi);
1195                 return err;
1196         }
1197
1198         err = startup_gfar(dev);
1199         if (err) {
1200                 napi_disable(&priv->napi);
1201                 return err;
1202         }
1203
1204         netif_start_queue(dev);
1205
1206         return err;
1207 }
1208
1209 static inline struct txfcb *gfar_add_fcb(struct sk_buff *skb)
1210 {
1211         struct txfcb *fcb = (struct txfcb *)skb_push (skb, GMAC_FCB_LEN);
1212
1213         cacheable_memzero(fcb, GMAC_FCB_LEN);
1214
1215         return fcb;
1216 }
1217
1218 static inline void gfar_tx_checksum(struct sk_buff *skb, struct txfcb *fcb)
1219 {
1220         u8 flags = 0;
1221
1222         /* If we're here, it's a IP packet with a TCP or UDP
1223          * payload.  We set it to checksum, using a pseudo-header
1224          * we provide
1225          */
1226         flags = TXFCB_DEFAULT;
1227
1228         /* Tell the controller what the protocol is */
1229         /* And provide the already calculated phcs */
1230         if (ip_hdr(skb)->protocol == IPPROTO_UDP) {
1231                 flags |= TXFCB_UDP;
1232                 fcb->phcs = udp_hdr(skb)->check;
1233         } else
1234                 fcb->phcs = tcp_hdr(skb)->check;
1235
1236         /* l3os is the distance between the start of the
1237          * frame (skb->data) and the start of the IP hdr.
1238          * l4os is the distance between the start of the
1239          * l3 hdr and the l4 hdr */
1240         fcb->l3os = (u16)(skb_network_offset(skb) - GMAC_FCB_LEN);
1241         fcb->l4os = skb_network_header_len(skb);
1242
1243         fcb->flags = flags;
1244 }
1245
1246 void inline gfar_tx_vlan(struct sk_buff *skb, struct txfcb *fcb)
1247 {
1248         fcb->flags |= TXFCB_VLN;
1249         fcb->vlctl = vlan_tx_tag_get(skb);
1250 }
1251
1252 static inline struct txbd8 *skip_txbd(struct txbd8 *bdp, int stride,
1253                                struct txbd8 *base, int ring_size)
1254 {
1255         struct txbd8 *new_bd = bdp + stride;
1256
1257         return (new_bd >= (base + ring_size)) ? (new_bd - ring_size) : new_bd;
1258 }
1259
1260 static inline struct txbd8 *next_txbd(struct txbd8 *bdp, struct txbd8 *base,
1261                 int ring_size)
1262 {
1263         return skip_txbd(bdp, 1, base, ring_size);
1264 }
1265
1266 /* This is called by the kernel when a frame is ready for transmission. */
1267 /* It is pointed to by the dev->hard_start_xmit function pointer */
1268 static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev)
1269 {
1270         struct gfar_private *priv = netdev_priv(dev);
1271         struct txfcb *fcb = NULL;
1272         struct txbd8 *txbdp, *txbdp_start, *base;
1273         u32 lstatus;
1274         int i;
1275         u32 bufaddr;
1276         unsigned long flags;
1277         unsigned int nr_frags, length;
1278
1279         base = priv->tx_bd_base;
1280
1281         /* total number of fragments in the SKB */
1282         nr_frags = skb_shinfo(skb)->nr_frags;
1283
1284         spin_lock_irqsave(&priv->txlock, flags);
1285
1286         /* check if there is space to queue this packet */
1287         if ((nr_frags+1) > priv->num_txbdfree) {
1288                 /* no space, stop the queue */
1289                 netif_stop_queue(dev);
1290                 dev->stats.tx_fifo_errors++;
1291                 spin_unlock_irqrestore(&priv->txlock, flags);
1292                 return NETDEV_TX_BUSY;
1293         }
1294
1295         /* Update transmit stats */
1296         dev->stats.tx_bytes += skb->len;
1297
1298         txbdp = txbdp_start = priv->cur_tx;
1299
1300         if (nr_frags == 0) {
1301                 lstatus = txbdp->lstatus | BD_LFLAG(TXBD_LAST | TXBD_INTERRUPT);
1302         } else {
1303                 /* Place the fragment addresses and lengths into the TxBDs */
1304                 for (i = 0; i < nr_frags; i++) {
1305                         /* Point at the next BD, wrapping as needed */
1306                         txbdp = next_txbd(txbdp, base, priv->tx_ring_size);
1307
1308                         length = skb_shinfo(skb)->frags[i].size;
1309
1310                         lstatus = txbdp->lstatus | length |
1311                                 BD_LFLAG(TXBD_READY);
1312
1313                         /* Handle the last BD specially */
1314                         if (i == nr_frags - 1)
1315                                 lstatus |= BD_LFLAG(TXBD_LAST | TXBD_INTERRUPT);
1316
1317                         bufaddr = dma_map_page(&dev->dev,
1318                                         skb_shinfo(skb)->frags[i].page,
1319                                         skb_shinfo(skb)->frags[i].page_offset,
1320                                         length,
1321                                         DMA_TO_DEVICE);
1322
1323                         /* set the TxBD length and buffer pointer */
1324                         txbdp->bufPtr = bufaddr;
1325                         txbdp->lstatus = lstatus;
1326                 }
1327
1328                 lstatus = txbdp_start->lstatus;
1329         }
1330
1331         /* Set up checksumming */
1332         if (CHECKSUM_PARTIAL == skb->ip_summed) {
1333                 fcb = gfar_add_fcb(skb);
1334                 lstatus |= BD_LFLAG(TXBD_TOE);
1335                 gfar_tx_checksum(skb, fcb);
1336         }
1337
1338         if (priv->vlgrp && vlan_tx_tag_present(skb)) {
1339                 if (unlikely(NULL == fcb)) {
1340                         fcb = gfar_add_fcb(skb);
1341                         lstatus |= BD_LFLAG(TXBD_TOE);
1342                 }
1343
1344                 gfar_tx_vlan(skb, fcb);
1345         }
1346
1347         /* setup the TxBD length and buffer pointer for the first BD */
1348         priv->tx_skbuff[priv->skb_curtx] = skb;
1349         txbdp_start->bufPtr = dma_map_single(&dev->dev, skb->data,
1350                         skb_headlen(skb), DMA_TO_DEVICE);
1351
1352         lstatus |= BD_LFLAG(TXBD_CRC | TXBD_READY) | skb_headlen(skb);
1353
1354         /*
1355          * The powerpc-specific eieio() is used, as wmb() has too strong
1356          * semantics (it requires synchronization between cacheable and
1357          * uncacheable mappings, which eieio doesn't provide and which we
1358          * don't need), thus requiring a more expensive sync instruction.  At
1359          * some point, the set of architecture-independent barrier functions
1360          * should be expanded to include weaker barriers.
1361          */
1362         eieio();
1363
1364         txbdp_start->lstatus = lstatus;
1365
1366         /* Update the current skb pointer to the next entry we will use
1367          * (wrapping if necessary) */
1368         priv->skb_curtx = (priv->skb_curtx + 1) &
1369                 TX_RING_MOD_MASK(priv->tx_ring_size);
1370
1371         priv->cur_tx = next_txbd(txbdp, base, priv->tx_ring_size);
1372
1373         /* reduce TxBD free count */
1374         priv->num_txbdfree -= (nr_frags + 1);
1375
1376         dev->trans_start = jiffies;
1377
1378         /* If the next BD still needs to be cleaned up, then the bds
1379            are full.  We need to tell the kernel to stop sending us stuff. */
1380         if (!priv->num_txbdfree) {
1381                 netif_stop_queue(dev);
1382
1383                 dev->stats.tx_fifo_errors++;
1384         }
1385
1386         /* Tell the DMA to go go go */
1387         gfar_write(&priv->regs->tstat, TSTAT_CLEAR_THALT);
1388
1389         /* Unlock priv */
1390         spin_unlock_irqrestore(&priv->txlock, flags);
1391
1392         return 0;
1393 }
1394
1395 /* Stops the kernel queue, and halts the controller */
1396 static int gfar_close(struct net_device *dev)
1397 {
1398         struct gfar_private *priv = netdev_priv(dev);
1399
1400         napi_disable(&priv->napi);
1401
1402         cancel_work_sync(&priv->reset_task);
1403         stop_gfar(dev);
1404
1405         /* Disconnect from the PHY */
1406         phy_disconnect(priv->phydev);
1407         priv->phydev = NULL;
1408
1409         netif_stop_queue(dev);
1410
1411         return 0;
1412 }
1413
1414 /* Changes the mac address if the controller is not running. */
1415 static int gfar_set_mac_address(struct net_device *dev)
1416 {
1417         gfar_set_mac_for_addr(dev, 0, dev->dev_addr);
1418
1419         return 0;
1420 }
1421
1422
1423 /* Enables and disables VLAN insertion/extraction */
1424 static void gfar_vlan_rx_register(struct net_device *dev,
1425                 struct vlan_group *grp)
1426 {
1427         struct gfar_private *priv = netdev_priv(dev);
1428         unsigned long flags;
1429         u32 tempval;
1430
1431         spin_lock_irqsave(&priv->rxlock, flags);
1432
1433         priv->vlgrp = grp;
1434
1435         if (grp) {
1436                 /* Enable VLAN tag insertion */
1437                 tempval = gfar_read(&priv->regs->tctrl);
1438                 tempval |= TCTRL_VLINS;
1439
1440                 gfar_write(&priv->regs->tctrl, tempval);
1441
1442                 /* Enable VLAN tag extraction */
1443                 tempval = gfar_read(&priv->regs->rctrl);
1444                 tempval |= RCTRL_VLEX;
1445                 tempval |= (RCTRL_VLEX | RCTRL_PRSDEP_INIT);
1446                 gfar_write(&priv->regs->rctrl, tempval);
1447         } else {
1448                 /* Disable VLAN tag insertion */
1449                 tempval = gfar_read(&priv->regs->tctrl);
1450                 tempval &= ~TCTRL_VLINS;
1451                 gfar_write(&priv->regs->tctrl, tempval);
1452
1453                 /* Disable VLAN tag extraction */
1454                 tempval = gfar_read(&priv->regs->rctrl);
1455                 tempval &= ~RCTRL_VLEX;
1456                 /* If parse is no longer required, then disable parser */
1457                 if (tempval & RCTRL_REQ_PARSER)
1458                         tempval |= RCTRL_PRSDEP_INIT;
1459                 else
1460                         tempval &= ~RCTRL_PRSDEP_INIT;
1461                 gfar_write(&priv->regs->rctrl, tempval);
1462         }
1463
1464         gfar_change_mtu(dev, dev->mtu);
1465
1466         spin_unlock_irqrestore(&priv->rxlock, flags);
1467 }
1468
1469 static int gfar_change_mtu(struct net_device *dev, int new_mtu)
1470 {
1471         int tempsize, tempval;
1472         struct gfar_private *priv = netdev_priv(dev);
1473         int oldsize = priv->rx_buffer_size;
1474         int frame_size = new_mtu + ETH_HLEN;
1475
1476         if (priv->vlgrp)
1477                 frame_size += VLAN_HLEN;
1478
1479         if ((frame_size < 64) || (frame_size > JUMBO_FRAME_SIZE)) {
1480                 if (netif_msg_drv(priv))
1481                         printk(KERN_ERR "%s: Invalid MTU setting\n",
1482                                         dev->name);
1483                 return -EINVAL;
1484         }
1485
1486         if (gfar_uses_fcb(priv))
1487                 frame_size += GMAC_FCB_LEN;
1488
1489         frame_size += priv->padding;
1490
1491         tempsize =
1492             (frame_size & ~(INCREMENTAL_BUFFER_SIZE - 1)) +
1493             INCREMENTAL_BUFFER_SIZE;
1494
1495         /* Only stop and start the controller if it isn't already
1496          * stopped, and we changed something */
1497         if ((oldsize != tempsize) && (dev->flags & IFF_UP))
1498                 stop_gfar(dev);
1499
1500         priv->rx_buffer_size = tempsize;
1501
1502         dev->mtu = new_mtu;
1503
1504         gfar_write(&priv->regs->mrblr, priv->rx_buffer_size);
1505         gfar_write(&priv->regs->maxfrm, priv->rx_buffer_size);
1506
1507         /* If the mtu is larger than the max size for standard
1508          * ethernet frames (ie, a jumbo frame), then set maccfg2
1509          * to allow huge frames, and to check the length */
1510         tempval = gfar_read(&priv->regs->maccfg2);
1511
1512         if (priv->rx_buffer_size > DEFAULT_RX_BUFFER_SIZE)
1513                 tempval |= (MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK);
1514         else
1515                 tempval &= ~(MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK);
1516
1517         gfar_write(&priv->regs->maccfg2, tempval);
1518
1519         if ((oldsize != tempsize) && (dev->flags & IFF_UP))
1520                 startup_gfar(dev);
1521
1522         return 0;
1523 }
1524
1525 /* gfar_reset_task gets scheduled when a packet has not been
1526  * transmitted after a set amount of time.
1527  * For now, assume that clearing out all the structures, and
1528  * starting over will fix the problem.
1529  */
1530 static void gfar_reset_task(struct work_struct *work)
1531 {
1532         struct gfar_private *priv = container_of(work, struct gfar_private,
1533                         reset_task);
1534         struct net_device *dev = priv->dev;
1535
1536         if (dev->flags & IFF_UP) {
1537                 stop_gfar(dev);
1538                 startup_gfar(dev);
1539         }
1540
1541         netif_tx_schedule_all(dev);
1542 }
1543
1544 static void gfar_timeout(struct net_device *dev)
1545 {
1546         struct gfar_private *priv = netdev_priv(dev);
1547
1548         dev->stats.tx_errors++;
1549         schedule_work(&priv->reset_task);
1550 }
1551
1552 /* Interrupt Handler for Transmit complete */
1553 static int gfar_clean_tx_ring(struct net_device *dev)
1554 {
1555         struct gfar_private *priv = netdev_priv(dev);
1556         struct txbd8 *bdp;
1557         struct txbd8 *lbdp = NULL;
1558         struct txbd8 *base = priv->tx_bd_base;
1559         struct sk_buff *skb;
1560         int skb_dirtytx;
1561         int tx_ring_size = priv->tx_ring_size;
1562         int frags = 0;
1563         int i;
1564         int howmany = 0;
1565         u32 lstatus;
1566
1567         bdp = priv->dirty_tx;
1568         skb_dirtytx = priv->skb_dirtytx;
1569
1570         while ((skb = priv->tx_skbuff[skb_dirtytx])) {
1571                 frags = skb_shinfo(skb)->nr_frags;
1572                 lbdp = skip_txbd(bdp, frags, base, tx_ring_size);
1573
1574                 lstatus = lbdp->lstatus;
1575
1576                 /* Only clean completed frames */
1577                 if ((lstatus & BD_LFLAG(TXBD_READY)) &&
1578                                 (lstatus & BD_LENGTH_MASK))
1579                         break;
1580
1581                 dma_unmap_single(&dev->dev,
1582                                 bdp->bufPtr,
1583                                 bdp->length,
1584                                 DMA_TO_DEVICE);
1585
1586                 bdp->lstatus &= BD_LFLAG(TXBD_WRAP);
1587                 bdp = next_txbd(bdp, base, tx_ring_size);
1588
1589                 for (i = 0; i < frags; i++) {
1590                         dma_unmap_page(&dev->dev,
1591                                         bdp->bufPtr,
1592                                         bdp->length,
1593                                         DMA_TO_DEVICE);
1594                         bdp->lstatus &= BD_LFLAG(TXBD_WRAP);
1595                         bdp = next_txbd(bdp, base, tx_ring_size);
1596                 }
1597
1598                 dev_kfree_skb_any(skb);
1599                 priv->tx_skbuff[skb_dirtytx] = NULL;
1600
1601                 skb_dirtytx = (skb_dirtytx + 1) &
1602                         TX_RING_MOD_MASK(tx_ring_size);
1603
1604                 howmany++;
1605                 priv->num_txbdfree += frags + 1;
1606         }
1607
1608         /* If we freed a buffer, we can restart transmission, if necessary */
1609         if (netif_queue_stopped(dev) && priv->num_txbdfree)
1610                 netif_wake_queue(dev);
1611
1612         /* Update dirty indicators */
1613         priv->skb_dirtytx = skb_dirtytx;
1614         priv->dirty_tx = bdp;
1615
1616         dev->stats.tx_packets += howmany;
1617
1618         return howmany;
1619 }
1620
1621 static void gfar_schedule_cleanup(struct net_device *dev)
1622 {
1623         struct gfar_private *priv = netdev_priv(dev);
1624         unsigned long flags;
1625
1626         spin_lock_irqsave(&priv->txlock, flags);
1627         spin_lock(&priv->rxlock);
1628
1629         if (netif_rx_schedule_prep(&priv->napi)) {
1630                 gfar_write(&priv->regs->imask, IMASK_RTX_DISABLED);
1631                 __netif_rx_schedule(&priv->napi);
1632         } else {
1633                 /*
1634                  * Clear IEVENT, so interrupts aren't called again
1635                  * because of the packets that have already arrived.
1636                  */
1637                 gfar_write(&priv->regs->ievent, IEVENT_RTX_MASK);
1638         }
1639
1640         spin_unlock(&priv->rxlock);
1641         spin_unlock_irqrestore(&priv->txlock, flags);
1642 }
1643
1644 /* Interrupt Handler for Transmit complete */
1645 static irqreturn_t gfar_transmit(int irq, void *dev_id)
1646 {
1647         gfar_schedule_cleanup((struct net_device *)dev_id);
1648         return IRQ_HANDLED;
1649 }
1650
1651 static void gfar_new_rxbdp(struct net_device *dev, struct rxbd8 *bdp,
1652                 struct sk_buff *skb)
1653 {
1654         struct gfar_private *priv = netdev_priv(dev);
1655         u32 lstatus;
1656
1657         bdp->bufPtr = dma_map_single(&dev->dev, skb->data,
1658                         priv->rx_buffer_size, DMA_FROM_DEVICE);
1659
1660         lstatus = BD_LFLAG(RXBD_EMPTY | RXBD_INTERRUPT);
1661
1662         if (bdp == priv->rx_bd_base + priv->rx_ring_size - 1)
1663                 lstatus |= BD_LFLAG(RXBD_WRAP);
1664
1665         eieio();
1666
1667         bdp->lstatus = lstatus;
1668 }
1669
1670
1671 struct sk_buff * gfar_new_skb(struct net_device *dev)
1672 {
1673         unsigned int alignamount;
1674         struct gfar_private *priv = netdev_priv(dev);
1675         struct sk_buff *skb = NULL;
1676
1677         /* We have to allocate the skb, so keep trying till we succeed */
1678         skb = netdev_alloc_skb(dev, priv->rx_buffer_size + RXBUF_ALIGNMENT);
1679
1680         if (!skb)
1681                 return NULL;
1682
1683         alignamount = RXBUF_ALIGNMENT -
1684                 (((unsigned long) skb->data) & (RXBUF_ALIGNMENT - 1));
1685
1686         /* We need the data buffer to be aligned properly.  We will reserve
1687          * as many bytes as needed to align the data properly
1688          */
1689         skb_reserve(skb, alignamount);
1690
1691         return skb;
1692 }
1693
1694 static inline void count_errors(unsigned short status, struct net_device *dev)
1695 {
1696         struct gfar_private *priv = netdev_priv(dev);
1697         struct net_device_stats *stats = &dev->stats;
1698         struct gfar_extra_stats *estats = &priv->extra_stats;
1699
1700         /* If the packet was truncated, none of the other errors
1701          * matter */
1702         if (status & RXBD_TRUNCATED) {
1703                 stats->rx_length_errors++;
1704
1705                 estats->rx_trunc++;
1706
1707                 return;
1708         }
1709         /* Count the errors, if there were any */
1710         if (status & (RXBD_LARGE | RXBD_SHORT)) {
1711                 stats->rx_length_errors++;
1712
1713                 if (status & RXBD_LARGE)
1714                         estats->rx_large++;
1715                 else
1716                         estats->rx_short++;
1717         }
1718         if (status & RXBD_NONOCTET) {
1719                 stats->rx_frame_errors++;
1720                 estats->rx_nonoctet++;
1721         }
1722         if (status & RXBD_CRCERR) {
1723                 estats->rx_crcerr++;
1724                 stats->rx_crc_errors++;
1725         }
1726         if (status & RXBD_OVERRUN) {
1727                 estats->rx_overrun++;
1728                 stats->rx_crc_errors++;
1729         }
1730 }
1731
1732 irqreturn_t gfar_receive(int irq, void *dev_id)
1733 {
1734         gfar_schedule_cleanup((struct net_device *)dev_id);
1735         return IRQ_HANDLED;
1736 }
1737
1738 static inline void gfar_rx_checksum(struct sk_buff *skb, struct rxfcb *fcb)
1739 {
1740         /* If valid headers were found, and valid sums
1741          * were verified, then we tell the kernel that no
1742          * checksumming is necessary.  Otherwise, it is */
1743         if ((fcb->flags & RXFCB_CSUM_MASK) == (RXFCB_CIP | RXFCB_CTU))
1744                 skb->ip_summed = CHECKSUM_UNNECESSARY;
1745         else
1746                 skb->ip_summed = CHECKSUM_NONE;
1747 }
1748
1749
1750 /* gfar_process_frame() -- handle one incoming packet if skb
1751  * isn't NULL.  */
1752 static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb,
1753                               int amount_pull)
1754 {
1755         struct gfar_private *priv = netdev_priv(dev);
1756         struct rxfcb *fcb = NULL;
1757
1758         int ret;
1759
1760         /* fcb is at the beginning if exists */
1761         fcb = (struct rxfcb *)skb->data;
1762
1763         /* Remove the FCB from the skb */
1764         /* Remove the padded bytes, if there are any */
1765         if (amount_pull)
1766                 skb_pull(skb, amount_pull);
1767
1768         if (priv->rx_csum_enable)
1769                 gfar_rx_checksum(skb, fcb);
1770
1771         /* Tell the skb what kind of packet this is */
1772         skb->protocol = eth_type_trans(skb, dev);
1773
1774         /* Send the packet up the stack */
1775         if (unlikely(priv->vlgrp && (fcb->flags & RXFCB_VLN)))
1776                 ret = vlan_hwaccel_receive_skb(skb, priv->vlgrp, fcb->vlctl);
1777         else
1778                 ret = netif_receive_skb(skb);
1779
1780         if (NET_RX_DROP == ret)
1781                 priv->extra_stats.kernel_dropped++;
1782
1783         return 0;
1784 }
1785
1786 /* gfar_clean_rx_ring() -- Processes each frame in the rx ring
1787  *   until the budget/quota has been reached. Returns the number
1788  *   of frames handled
1789  */
1790 int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit)
1791 {
1792         struct rxbd8 *bdp, *base;
1793         struct sk_buff *skb;
1794         int pkt_len;
1795         int amount_pull;
1796         int howmany = 0;
1797         struct gfar_private *priv = netdev_priv(dev);
1798
1799         /* Get the first full descriptor */
1800         bdp = priv->cur_rx;
1801         base = priv->rx_bd_base;
1802
1803         amount_pull = (gfar_uses_fcb(priv) ? GMAC_FCB_LEN : 0) +
1804                 priv->padding;
1805
1806         while (!((bdp->status & RXBD_EMPTY) || (--rx_work_limit < 0))) {
1807                 struct sk_buff *newskb;
1808                 rmb();
1809
1810                 /* Add another skb for the future */
1811                 newskb = gfar_new_skb(dev);
1812
1813                 skb = priv->rx_skbuff[priv->skb_currx];
1814
1815                 dma_unmap_single(&priv->dev->dev, bdp->bufPtr,
1816                                 priv->rx_buffer_size, DMA_FROM_DEVICE);
1817
1818                 /* We drop the frame if we failed to allocate a new buffer */
1819                 if (unlikely(!newskb || !(bdp->status & RXBD_LAST) ||
1820                                  bdp->status & RXBD_ERR)) {
1821                         count_errors(bdp->status, dev);
1822
1823                         if (unlikely(!newskb))
1824                                 newskb = skb;
1825                         else if (skb)
1826                                 dev_kfree_skb_any(skb);
1827                 } else {
1828                         /* Increment the number of packets */
1829                         dev->stats.rx_packets++;
1830                         howmany++;
1831
1832                         if (likely(skb)) {
1833                                 pkt_len = bdp->length - ETH_FCS_LEN;
1834                                 /* Remove the FCS from the packet length */
1835                                 skb_put(skb, pkt_len);
1836                                 dev->stats.rx_bytes += pkt_len;
1837
1838                                 gfar_process_frame(dev, skb, amount_pull);
1839
1840                         } else {
1841                                 if (netif_msg_rx_err(priv))
1842                                         printk(KERN_WARNING
1843                                                "%s: Missing skb!\n", dev->name);
1844                                 dev->stats.rx_dropped++;
1845                                 priv->extra_stats.rx_skbmissing++;
1846                         }
1847
1848                 }
1849
1850                 priv->rx_skbuff[priv->skb_currx] = newskb;
1851
1852                 /* Setup the new bdp */
1853                 gfar_new_rxbdp(dev, bdp, newskb);
1854
1855                 /* Update to the next pointer */
1856                 bdp = next_bd(bdp, base, priv->rx_ring_size);
1857
1858                 /* update to point at the next skb */
1859                 priv->skb_currx =
1860                     (priv->skb_currx + 1) &
1861                     RX_RING_MOD_MASK(priv->rx_ring_size);
1862         }
1863
1864         /* Update the current rxbd pointer to be the next one */
1865         priv->cur_rx = bdp;
1866
1867         return howmany;
1868 }
1869
1870 static int gfar_poll(struct napi_struct *napi, int budget)
1871 {
1872         struct gfar_private *priv = container_of(napi, struct gfar_private, napi);
1873         struct net_device *dev = priv->dev;
1874         int tx_cleaned = 0;
1875         int rx_cleaned = 0;
1876         unsigned long flags;
1877
1878         /* Clear IEVENT, so interrupts aren't called again
1879          * because of the packets that have already arrived */
1880         gfar_write(&priv->regs->ievent, IEVENT_RTX_MASK);
1881
1882         /* If we fail to get the lock, don't bother with the TX BDs */
1883         if (spin_trylock_irqsave(&priv->txlock, flags)) {
1884                 tx_cleaned = gfar_clean_tx_ring(dev);
1885                 spin_unlock_irqrestore(&priv->txlock, flags);
1886         }
1887
1888         rx_cleaned = gfar_clean_rx_ring(dev, budget);
1889
1890         if (tx_cleaned)
1891                 return budget;
1892
1893         if (rx_cleaned < budget) {
1894                 netif_rx_complete(napi);
1895
1896                 /* Clear the halt bit in RSTAT */
1897                 gfar_write(&priv->regs->rstat, RSTAT_CLEAR_RHALT);
1898
1899                 gfar_write(&priv->regs->imask, IMASK_DEFAULT);
1900
1901                 /* If we are coalescing interrupts, update the timer */
1902                 /* Otherwise, clear it */
1903                 if (likely(priv->rxcoalescing)) {
1904                         gfar_write(&priv->regs->rxic, 0);
1905                         gfar_write(&priv->regs->rxic, priv->rxic);
1906                 }
1907                 if (likely(priv->txcoalescing)) {
1908                         gfar_write(&priv->regs->txic, 0);
1909                         gfar_write(&priv->regs->txic, priv->txic);
1910                 }
1911         }
1912
1913         return rx_cleaned;
1914 }
1915
1916 #ifdef CONFIG_NET_POLL_CONTROLLER
1917 /*
1918  * Polling 'interrupt' - used by things like netconsole to send skbs
1919  * without having to re-enable interrupts. It's not called while
1920  * the interrupt routine is executing.
1921  */
1922 static void gfar_netpoll(struct net_device *dev)
1923 {
1924         struct gfar_private *priv = netdev_priv(dev);
1925
1926         /* If the device has multiple interrupts, run tx/rx */
1927         if (priv->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) {
1928                 disable_irq(priv->interruptTransmit);
1929                 disable_irq(priv->interruptReceive);
1930                 disable_irq(priv->interruptError);
1931                 gfar_interrupt(priv->interruptTransmit, dev);
1932                 enable_irq(priv->interruptError);
1933                 enable_irq(priv->interruptReceive);
1934                 enable_irq(priv->interruptTransmit);
1935         } else {
1936                 disable_irq(priv->interruptTransmit);
1937                 gfar_interrupt(priv->interruptTransmit, dev);
1938                 enable_irq(priv->interruptTransmit);
1939         }
1940 }
1941 #endif
1942
1943 /* The interrupt handler for devices with one interrupt */
1944 static irqreturn_t gfar_interrupt(int irq, void *dev_id)
1945 {
1946         struct net_device *dev = dev_id;
1947         struct gfar_private *priv = netdev_priv(dev);
1948
1949         /* Save ievent for future reference */
1950         u32 events = gfar_read(&priv->regs->ievent);
1951
1952         /* Check for reception */
1953         if (events & IEVENT_RX_MASK)
1954                 gfar_receive(irq, dev_id);
1955
1956         /* Check for transmit completion */
1957         if (events & IEVENT_TX_MASK)
1958                 gfar_transmit(irq, dev_id);
1959
1960         /* Check for errors */
1961         if (events & IEVENT_ERR_MASK)
1962                 gfar_error(irq, dev_id);
1963
1964         return IRQ_HANDLED;
1965 }
1966
1967 /* Called every time the controller might need to be made
1968  * aware of new link state.  The PHY code conveys this
1969  * information through variables in the phydev structure, and this
1970  * function converts those variables into the appropriate
1971  * register values, and can bring down the device if needed.
1972  */
1973 static void adjust_link(struct net_device *dev)
1974 {
1975         struct gfar_private *priv = netdev_priv(dev);
1976         struct gfar __iomem *regs = priv->regs;
1977         unsigned long flags;
1978         struct phy_device *phydev = priv->phydev;
1979         int new_state = 0;
1980
1981         spin_lock_irqsave(&priv->txlock, flags);
1982         if (phydev->link) {
1983                 u32 tempval = gfar_read(&regs->maccfg2);
1984                 u32 ecntrl = gfar_read(&regs->ecntrl);
1985
1986                 /* Now we make sure that we can be in full duplex mode.
1987                  * If not, we operate in half-duplex mode. */
1988                 if (phydev->duplex != priv->oldduplex) {
1989                         new_state = 1;
1990                         if (!(phydev->duplex))
1991                                 tempval &= ~(MACCFG2_FULL_DUPLEX);
1992                         else
1993                                 tempval |= MACCFG2_FULL_DUPLEX;
1994
1995                         priv->oldduplex = phydev->duplex;
1996                 }
1997
1998                 if (phydev->speed != priv->oldspeed) {
1999                         new_state = 1;
2000                         switch (phydev->speed) {
2001                         case 1000:
2002                                 tempval =
2003                                     ((tempval & ~(MACCFG2_IF)) | MACCFG2_GMII);
2004
2005                                 ecntrl &= ~(ECNTRL_R100);
2006                                 break;
2007                         case 100:
2008                         case 10:
2009                                 tempval =
2010                                     ((tempval & ~(MACCFG2_IF)) | MACCFG2_MII);
2011
2012                                 /* Reduced mode distinguishes
2013                                  * between 10 and 100 */
2014                                 if (phydev->speed == SPEED_100)
2015                                         ecntrl |= ECNTRL_R100;
2016                                 else
2017                                         ecntrl &= ~(ECNTRL_R100);
2018                                 break;
2019                         default:
2020                                 if (netif_msg_link(priv))
2021                                         printk(KERN_WARNING
2022                                                 "%s: Ack!  Speed (%d) is not 10/100/1000!\n",
2023                                                 dev->name, phydev->speed);
2024                                 break;
2025                         }
2026
2027                         priv->oldspeed = phydev->speed;
2028                 }
2029
2030                 gfar_write(&regs->maccfg2, tempval);
2031                 gfar_write(&regs->ecntrl, ecntrl);
2032
2033                 if (!priv->oldlink) {
2034                         new_state = 1;
2035                         priv->oldlink = 1;
2036                 }
2037         } else if (priv->oldlink) {
2038                 new_state = 1;
2039                 priv->oldlink = 0;
2040                 priv->oldspeed = 0;
2041                 priv->oldduplex = -1;
2042         }
2043
2044         if (new_state && netif_msg_link(priv))
2045                 phy_print_status(phydev);
2046
2047         spin_unlock_irqrestore(&priv->txlock, flags);
2048 }
2049
2050 /* Update the hash table based on the current list of multicast
2051  * addresses we subscribe to.  Also, change the promiscuity of
2052  * the device based on the flags (this function is called
2053  * whenever dev->flags is changed */
2054 static void gfar_set_multi(struct net_device *dev)
2055 {
2056         struct dev_mc_list *mc_ptr;
2057         struct gfar_private *priv = netdev_priv(dev);
2058         struct gfar __iomem *regs = priv->regs;
2059         u32 tempval;
2060
2061         if(dev->flags & IFF_PROMISC) {
2062                 /* Set RCTRL to PROM */
2063                 tempval = gfar_read(&regs->rctrl);
2064                 tempval |= RCTRL_PROM;
2065                 gfar_write(&regs->rctrl, tempval);
2066         } else {
2067                 /* Set RCTRL to not PROM */
2068                 tempval = gfar_read(&regs->rctrl);
2069                 tempval &= ~(RCTRL_PROM);
2070                 gfar_write(&regs->rctrl, tempval);
2071         }
2072
2073         if(dev->flags & IFF_ALLMULTI) {
2074                 /* Set the hash to rx all multicast frames */
2075                 gfar_write(&regs->igaddr0, 0xffffffff);
2076                 gfar_write(&regs->igaddr1, 0xffffffff);
2077                 gfar_write(&regs->igaddr2, 0xffffffff);
2078                 gfar_write(&regs->igaddr3, 0xffffffff);
2079                 gfar_write(&regs->igaddr4, 0xffffffff);
2080                 gfar_write(&regs->igaddr5, 0xffffffff);
2081                 gfar_write(&regs->igaddr6, 0xffffffff);
2082                 gfar_write(&regs->igaddr7, 0xffffffff);
2083                 gfar_write(&regs->gaddr0, 0xffffffff);
2084                 gfar_write(&regs->gaddr1, 0xffffffff);
2085                 gfar_write(&regs->gaddr2, 0xffffffff);
2086                 gfar_write(&regs->gaddr3, 0xffffffff);
2087                 gfar_write(&regs->gaddr4, 0xffffffff);
2088                 gfar_write(&regs->gaddr5, 0xffffffff);
2089                 gfar_write(&regs->gaddr6, 0xffffffff);
2090                 gfar_write(&regs->gaddr7, 0xffffffff);
2091         } else {
2092                 int em_num;
2093                 int idx;
2094
2095                 /* zero out the hash */
2096                 gfar_write(&regs->igaddr0, 0x0);
2097                 gfar_write(&regs->igaddr1, 0x0);
2098                 gfar_write(&regs->igaddr2, 0x0);
2099                 gfar_write(&regs->igaddr3, 0x0);
2100                 gfar_write(&regs->igaddr4, 0x0);
2101                 gfar_write(&regs->igaddr5, 0x0);
2102                 gfar_write(&regs->igaddr6, 0x0);
2103                 gfar_write(&regs->igaddr7, 0x0);
2104                 gfar_write(&regs->gaddr0, 0x0);
2105                 gfar_write(&regs->gaddr1, 0x0);
2106                 gfar_write(&regs->gaddr2, 0x0);
2107                 gfar_write(&regs->gaddr3, 0x0);
2108                 gfar_write(&regs->gaddr4, 0x0);
2109                 gfar_write(&regs->gaddr5, 0x0);
2110                 gfar_write(&regs->gaddr6, 0x0);
2111                 gfar_write(&regs->gaddr7, 0x0);
2112
2113                 /* If we have extended hash tables, we need to
2114                  * clear the exact match registers to prepare for
2115                  * setting them */
2116                 if (priv->extended_hash) {
2117                         em_num = GFAR_EM_NUM + 1;
2118                         gfar_clear_exact_match(dev);
2119                         idx = 1;
2120                 } else {
2121                         idx = 0;
2122                         em_num = 0;
2123                 }
2124
2125                 if(dev->mc_count == 0)
2126                         return;
2127
2128                 /* Parse the list, and set the appropriate bits */
2129                 for(mc_ptr = dev->mc_list; mc_ptr; mc_ptr = mc_ptr->next) {
2130                         if (idx < em_num) {
2131                                 gfar_set_mac_for_addr(dev, idx,
2132                                                 mc_ptr->dmi_addr);
2133                                 idx++;
2134                         } else
2135                                 gfar_set_hash_for_addr(dev, mc_ptr->dmi_addr);
2136                 }
2137         }
2138
2139         return;
2140 }
2141
2142
2143 /* Clears each of the exact match registers to zero, so they
2144  * don't interfere with normal reception */
2145 static void gfar_clear_exact_match(struct net_device *dev)
2146 {
2147         int idx;
2148         u8 zero_arr[MAC_ADDR_LEN] = {0,0,0,0,0,0};
2149
2150         for(idx = 1;idx < GFAR_EM_NUM + 1;idx++)
2151                 gfar_set_mac_for_addr(dev, idx, (u8 *)zero_arr);
2152 }
2153
2154 /* Set the appropriate hash bit for the given addr */
2155 /* The algorithm works like so:
2156  * 1) Take the Destination Address (ie the multicast address), and
2157  * do a CRC on it (little endian), and reverse the bits of the
2158  * result.
2159  * 2) Use the 8 most significant bits as a hash into a 256-entry
2160  * table.  The table is controlled through 8 32-bit registers:
2161  * gaddr0-7.  gaddr0's MSB is entry 0, and gaddr7's LSB is
2162  * gaddr7.  This means that the 3 most significant bits in the
2163  * hash index which gaddr register to use, and the 5 other bits
2164  * indicate which bit (assuming an IBM numbering scheme, which
2165  * for PowerPC (tm) is usually the case) in the register holds
2166  * the entry. */
2167 static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr)
2168 {
2169         u32 tempval;
2170         struct gfar_private *priv = netdev_priv(dev);
2171         u32 result = ether_crc(MAC_ADDR_LEN, addr);
2172         int width = priv->hash_width;
2173         u8 whichbit = (result >> (32 - width)) & 0x1f;
2174         u8 whichreg = result >> (32 - width + 5);
2175         u32 value = (1 << (31-whichbit));
2176
2177         tempval = gfar_read(priv->hash_regs[whichreg]);
2178         tempval |= value;
2179         gfar_write(priv->hash_regs[whichreg], tempval);
2180
2181         return;
2182 }
2183
2184
2185 /* There are multiple MAC Address register pairs on some controllers
2186  * This function sets the numth pair to a given address
2187  */
2188 static void gfar_set_mac_for_addr(struct net_device *dev, int num, u8 *addr)
2189 {
2190         struct gfar_private *priv = netdev_priv(dev);
2191         int idx;
2192         char tmpbuf[MAC_ADDR_LEN];
2193         u32 tempval;
2194         u32 __iomem *macptr = &priv->regs->macstnaddr1;
2195
2196         macptr += num*2;
2197
2198         /* Now copy it into the mac registers backwards, cuz */
2199         /* little endian is silly */
2200         for (idx = 0; idx < MAC_ADDR_LEN; idx++)
2201                 tmpbuf[MAC_ADDR_LEN - 1 - idx] = addr[idx];
2202
2203         gfar_write(macptr, *((u32 *) (tmpbuf)));
2204
2205         tempval = *((u32 *) (tmpbuf + 4));
2206
2207         gfar_write(macptr+1, tempval);
2208 }
2209
2210 /* GFAR error interrupt handler */
2211 static irqreturn_t gfar_error(int irq, void *dev_id)
2212 {
2213         struct net_device *dev = dev_id;
2214         struct gfar_private *priv = netdev_priv(dev);
2215
2216         /* Save ievent for future reference */
2217         u32 events = gfar_read(&priv->regs->ievent);
2218
2219         /* Clear IEVENT */
2220         gfar_write(&priv->regs->ievent, events & IEVENT_ERR_MASK);
2221
2222         /* Magic Packet is not an error. */
2223         if ((priv->device_flags & FSL_GIANFAR_DEV_HAS_MAGIC_PACKET) &&
2224             (events & IEVENT_MAG))
2225                 events &= ~IEVENT_MAG;
2226
2227         /* Hmm... */
2228         if (netif_msg_rx_err(priv) || netif_msg_tx_err(priv))
2229                 printk(KERN_DEBUG "%s: error interrupt (ievent=0x%08x imask=0x%08x)\n",
2230                        dev->name, events, gfar_read(&priv->regs->imask));
2231
2232         /* Update the error counters */
2233         if (events & IEVENT_TXE) {
2234                 dev->stats.tx_errors++;
2235
2236                 if (events & IEVENT_LC)
2237                         dev->stats.tx_window_errors++;
2238                 if (events & IEVENT_CRL)
2239                         dev->stats.tx_aborted_errors++;
2240                 if (events & IEVENT_XFUN) {
2241                         if (netif_msg_tx_err(priv))
2242                                 printk(KERN_DEBUG "%s: TX FIFO underrun, "
2243                                        "packet dropped.\n", dev->name);
2244                         dev->stats.tx_dropped++;
2245                         priv->extra_stats.tx_underrun++;
2246
2247                         /* Reactivate the Tx Queues */
2248                         gfar_write(&priv->regs->tstat, TSTAT_CLEAR_THALT);
2249                 }
2250                 if (netif_msg_tx_err(priv))
2251                         printk(KERN_DEBUG "%s: Transmit Error\n", dev->name);
2252         }
2253         if (events & IEVENT_BSY) {
2254                 dev->stats.rx_errors++;
2255                 priv->extra_stats.rx_bsy++;
2256
2257                 gfar_receive(irq, dev_id);
2258
2259                 if (netif_msg_rx_err(priv))
2260                         printk(KERN_DEBUG "%s: busy error (rstat: %x)\n",
2261                                dev->name, gfar_read(&priv->regs->rstat));
2262         }
2263         if (events & IEVENT_BABR) {
2264                 dev->stats.rx_errors++;
2265                 priv->extra_stats.rx_babr++;
2266
2267                 if (netif_msg_rx_err(priv))
2268                         printk(KERN_DEBUG "%s: babbling RX error\n", dev->name);
2269         }
2270         if (events & IEVENT_EBERR) {
2271                 priv->extra_stats.eberr++;
2272                 if (netif_msg_rx_err(priv))
2273                         printk(KERN_DEBUG "%s: bus error\n", dev->name);
2274         }
2275         if ((events & IEVENT_RXC) && netif_msg_rx_status(priv))
2276                 printk(KERN_DEBUG "%s: control frame\n", dev->name);
2277
2278         if (events & IEVENT_BABT) {
2279                 priv->extra_stats.tx_babt++;
2280                 if (netif_msg_tx_err(priv))
2281                         printk(KERN_DEBUG "%s: babbling TX error\n", dev->name);
2282         }
2283         return IRQ_HANDLED;
2284 }
2285
2286 /* work with hotplug and coldplug */
2287 MODULE_ALIAS("platform:fsl-gianfar");
2288
2289 static struct of_device_id gfar_match[] =
2290 {
2291         {
2292                 .type = "network",
2293                 .compatible = "gianfar",
2294         },
2295         {},
2296 };
2297
2298 /* Structure for a device driver */
2299 static struct of_platform_driver gfar_driver = {
2300         .name = "fsl-gianfar",
2301         .match_table = gfar_match,
2302
2303         .probe = gfar_probe,
2304         .remove = gfar_remove,
2305         .suspend = gfar_suspend,
2306         .resume = gfar_resume,
2307 };
2308
2309 static int __init gfar_init(void)
2310 {
2311         int err = gfar_mdio_init();
2312
2313         if (err)
2314                 return err;
2315
2316         err = of_register_platform_driver(&gfar_driver);
2317
2318         if (err)
2319                 gfar_mdio_exit();
2320
2321         return err;
2322 }
2323
2324 static void __exit gfar_exit(void)
2325 {
2326         of_unregister_platform_driver(&gfar_driver);
2327         gfar_mdio_exit();
2328 }
2329
2330 module_init(gfar_init);
2331 module_exit(gfar_exit);
2332