drivers/char/synclink_gt.c

   1 /*
   2  * $Id: synclink_gt.c,v 4.25 2006/02/06 21:20:33 paulkf Exp $
   3  *
   4  * Device driver for Microgate SyncLink GT serial adapters.
   5  *
   6  * written by Paul Fulghum for Microgate Corporation
   7  * paulkf@microgate.com
   8  *
   9  * Microgate and SyncLink are trademarks of Microgate Corporation
  10  *
  11  * This code is released under the GNU General Public License (GPL)
  12  *
  13  * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
  14  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
  15  * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  16  * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
  17  * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  18  * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  19  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  20  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
  21  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  22  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
  23  * OF THE POSSIBILITY OF SUCH DAMAGE.
  24  */
  25
  26 /*
  27  * DEBUG OUTPUT DEFINITIONS
  28  *
  29  * uncomment lines below to enable specific types of debug output
  30  *
  31  * DBGINFO   information - most verbose output
  32  * DBGERR    serious errors
  33  * DBGBH     bottom half service routine debugging
  34  * DBGISR    interrupt service routine debugging
  35  * DBGDATA   output receive and transmit data
  36  * DBGTBUF   output transmit DMA buffers and registers
  37  * DBGRBUF   output receive DMA buffers and registers
  38  */
  39
  40 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
  41 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
  42 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
  43 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
  44 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
  45 //#define DBGTBUF(info) dump_tbufs(info)
  46 //#define DBGRBUF(info) dump_rbufs(info)
  47
  48
  49 #include <linux/config.h>
  50 #include <linux/module.h>
  51 #include <linux/version.h>
  52 #include <linux/errno.h>
  53 #include <linux/signal.h>
  54 #include <linux/sched.h>
  55 #include <linux/timer.h>
  56 #include <linux/interrupt.h>
  57 #include <linux/pci.h>
  58 #include <linux/tty.h>
  59 #include <linux/tty_flip.h>
  60 #include <linux/serial.h>
  61 #include <linux/major.h>
  62 #include <linux/string.h>
  63 #include <linux/fcntl.h>
  64 #include <linux/ptrace.h>
  65 #include <linux/ioport.h>
  66 #include <linux/mm.h>
  67 #include <linux/slab.h>
  68 #include <linux/netdevice.h>
  69 #include <linux/vmalloc.h>
  70 #include <linux/init.h>
  71 #include <linux/delay.h>
  72 #include <linux/ioctl.h>
  73 #include <linux/termios.h>
  74 #include <linux/bitops.h>
  75 #include <linux/workqueue.h>
  76 #include <linux/hdlc.h>
  77
  78 #include <asm/system.h>
  79 #include <asm/io.h>
  80 #include <asm/irq.h>
  81 #include <asm/dma.h>
  82 #include <asm/types.h>
  83 #include <asm/uaccess.h>
  84
  85 #include "linux/synclink.h"
  86
  87 #ifdef CONFIG_HDLC_MODULE
  88 #define CONFIG_HDLC 1
  89 #endif
  90
  91 /*
  92  * module identification
  93  */
  94 static char *driver_name     = "SyncLink GT";
  95 static char *driver_version  = "$Revision: 4.25 $";
  96 static char *tty_driver_name = "synclink_gt";
  97 static char *tty_dev_prefix  = "ttySLG";
  98 MODULE_LICENSE("GPL");
  99 #define MGSL_MAGIC 0x5401
 100 #define MAX_DEVICES 12
 101
 102 static struct pci_device_id pci_table[] = {
 103         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 104         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 105         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 106         {0,}, /* terminate list */
 107 };
 108 MODULE_DEVICE_TABLE(pci, pci_table);
 109
 110 static int  init_one(struct pci_dev *dev,const struct pci_device_id *ent);
 111 static void remove_one(struct pci_dev *dev);
 112 static struct pci_driver pci_driver = {
 113         .name           = "synclink_gt",
 114         .id_table       = pci_table,
 115         .probe          = init_one,
 116         .remove         = __devexit_p(remove_one),
 117 };
 118
 119 static int pci_registered;
 120
 121 /*
 122  * module configuration and status
 123  */
 124 static struct slgt_info *slgt_device_list;
 125 static int slgt_device_count;
 126
 127 static int ttymajor;
 128 static int debug_level;
 129 static int maxframe[MAX_DEVICES];
 130 static int dosyncppp[MAX_DEVICES];
 131
 132 module_param(ttymajor, int, 0);
 133 module_param(debug_level, int, 0);
 134 module_param_array(maxframe, int, NULL, 0);
 135 module_param_array(dosyncppp, int, NULL, 0);
 136
 137 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
 138 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
 139 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
 140 MODULE_PARM_DESC(dosyncppp, "Enable synchronous net device, 0=disable 1=enable");
 141
 142 /*
 143  * tty support and callbacks
 144  */
 145 #define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
 146
 147 static struct tty_driver *serial_driver;
 148
 149 static int  open(struct tty_struct *tty, struct file * filp);
 150 static void close(struct tty_struct *tty, struct file * filp);
 151 static void hangup(struct tty_struct *tty);
 152 static void set_termios(struct tty_struct *tty, struct termios *old_termios);
 153
 154 static int  write(struct tty_struct *tty, const unsigned char *buf, int count);
 155 static void put_char(struct tty_struct *tty, unsigned char ch);
 156 static void send_xchar(struct tty_struct *tty, char ch);
 157 static void wait_until_sent(struct tty_struct *tty, int timeout);
 158 static int  write_room(struct tty_struct *tty);
 159 static void flush_chars(struct tty_struct *tty);
 160 static void flush_buffer(struct tty_struct *tty);
 161 static void tx_hold(struct tty_struct *tty);
 162 static void tx_release(struct tty_struct *tty);
 163
 164 static int  ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
 165 static int  read_proc(char *page, char **start, off_t off, int count,int *eof, void *data);
 166 static int  chars_in_buffer(struct tty_struct *tty);
 167 static void throttle(struct tty_struct * tty);
 168 static void unthrottle(struct tty_struct * tty);
 169 static void set_break(struct tty_struct *tty, int break_state);
 170
 171 /*
 172  * generic HDLC support and callbacks
 173  */
 174 #ifdef CONFIG_HDLC
 175 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
 176 static void hdlcdev_tx_done(struct slgt_info *info);
 177 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
 178 static int  hdlcdev_init(struct slgt_info *info);
 179 static void hdlcdev_exit(struct slgt_info *info);
 180 #endif
 181
 182
 183 /*
 184  * device specific structures, macros and functions
 185  */
 186
 187 #define SLGT_MAX_PORTS 4
 188 #define SLGT_REG_SIZE  256
 189
 190 /*
 191  * conditional wait facility
 192  */
 193 struct cond_wait {
 194         struct cond_wait *next;
 195         wait_queue_head_t q;
 196         wait_queue_t wait;
 197         unsigned int data;
 198 };
 199 static void init_cond_wait(struct cond_wait *w, unsigned int data);
 200 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
 201 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
 202 static void flush_cond_wait(struct cond_wait **head);
 203
 204 /*
 205  * DMA buffer descriptor and access macros
 206  */
 207 struct slgt_desc
 208 {
 209         unsigned short count;
 210         unsigned short status;
 211         unsigned int pbuf;  /* physical address of data buffer */
 212         unsigned int next;  /* physical address of next descriptor */
 213
 214         /* driver book keeping */
 215         char *buf;          /* virtual  address of data buffer */
 216         unsigned int pdesc; /* physical address of this descriptor */
 217         dma_addr_t buf_dma_addr;
 218 };
 219
 220 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
 221 #define set_desc_next(a,b) (a).next   = cpu_to_le32((unsigned int)(b))
 222 #define set_desc_count(a,b)(a).count  = cpu_to_le16((unsigned short)(b))
 223 #define set_desc_eof(a,b)  (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
 224 #define desc_count(a)      (le16_to_cpu((a).count))
 225 #define desc_status(a)     (le16_to_cpu((a).status))
 226 #define desc_complete(a)   (le16_to_cpu((a).status) & BIT15)
 227 #define desc_eof(a)        (le16_to_cpu((a).status) & BIT2)
 228 #define desc_crc_error(a)  (le16_to_cpu((a).status) & BIT1)
 229 #define desc_abort(a)      (le16_to_cpu((a).status) & BIT0)
 230 #define desc_residue(a)    ((le16_to_cpu((a).status) & 0x38) >> 3)
 231
 232 struct _input_signal_events {
 233         int ri_up;
 234         int ri_down;
 235         int dsr_up;
 236         int dsr_down;
 237         int dcd_up;
 238         int dcd_down;
 239         int cts_up;
 240         int cts_down;
 241 };
 242
 243 /*
 244  * device instance data structure
 245  */
 246 struct slgt_info {
 247         void *if_ptr;           /* General purpose pointer (used by SPPP) */
 248
 249         struct slgt_info *next_device;  /* device list link */
 250
 251         int magic;
 252         int flags;
 253
 254         char device_name[25];
 255         struct pci_dev *pdev;
 256
 257         int port_count;  /* count of ports on adapter */
 258         int adapter_num; /* adapter instance number */
 259         int port_num;    /* port instance number */
 260
 261         /* array of pointers to port contexts on this adapter */
 262         struct slgt_info *port_array[SLGT_MAX_PORTS];
 263
 264         int                     count;          /* count of opens */
 265         int                     line;           /* tty line instance number */
 266         unsigned short          close_delay;
 267         unsigned short          closing_wait;   /* time to wait before closing */
 268
 269         struct mgsl_icount      icount;
 270
 271         struct tty_struct       *tty;
 272         int                     timeout;
 273         int                     x_char;         /* xon/xoff character */
 274         int                     blocked_open;   /* # of blocked opens */
 275         unsigned int            read_status_mask;
 276         unsigned int            ignore_status_mask;
 277
 278         wait_queue_head_t       open_wait;
 279         wait_queue_head_t       close_wait;
 280
 281         wait_queue_head_t       status_event_wait_q;
 282         wait_queue_head_t       event_wait_q;
 283         struct timer_list       tx_timer;
 284         struct timer_list       rx_timer;
 285
 286         unsigned int            gpio_present;
 287         struct cond_wait        *gpio_wait_q;
 288
 289         spinlock_t lock;        /* spinlock for synchronizing with ISR */
 290
 291         struct work_struct task;
 292         u32 pending_bh;
 293         int bh_requested;
 294         int bh_running;
 295
 296         int isr_overflow;
 297         int irq_requested;      /* nonzero if IRQ requested */
 298         int irq_occurred;       /* for diagnostics use */
 299
 300         /* device configuration */
 301
 302         unsigned int bus_type;
 303         unsigned int irq_level;
 304         unsigned long irq_flags;
 305
 306         unsigned char __iomem * reg_addr;  /* memory mapped registers address */
 307         u32 phys_reg_addr;
 308         int reg_addr_requested;
 309
 310         MGSL_PARAMS params;       /* communications parameters */
 311         u32 idle_mode;
 312         u32 max_frame_size;       /* as set by device config */
 313
 314         unsigned int raw_rx_size;
 315         unsigned int if_mode;
 316
 317         /* device status */
 318
 319         int rx_enabled;
 320         int rx_restart;
 321
 322         int tx_enabled;
 323         int tx_active;
 324
 325         unsigned char signals;    /* serial signal states */
 326         int init_error;  /* initialization error */
 327
 328         unsigned char *tx_buf;
 329         int tx_count;
 330
 331         char flag_buf[MAX_ASYNC_BUFFER_SIZE];
 332         char char_buf[MAX_ASYNC_BUFFER_SIZE];
 333         BOOLEAN drop_rts_on_tx_done;
 334         struct  _input_signal_events    input_signal_events;
 335
 336         int dcd_chkcount;       /* check counts to prevent */
 337         int cts_chkcount;       /* too many IRQs if a signal */
 338         int dsr_chkcount;       /* is floating */
 339         int ri_chkcount;
 340
 341         char *bufs;             /* virtual address of DMA buffer lists */
 342         dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
 343
 344         unsigned int rbuf_count;
 345         struct slgt_desc *rbufs;
 346         unsigned int rbuf_current;
 347         unsigned int rbuf_index;
 348
 349         unsigned int tbuf_count;
 350         struct slgt_desc *tbufs;
 351         unsigned int tbuf_current;
 352         unsigned int tbuf_start;
 353
 354         unsigned char *tmp_rbuf;
 355         unsigned int tmp_rbuf_count;
 356
 357         /* SPPP/Cisco HDLC device parts */
 358
 359         int netcount;
 360         int dosyncppp;
 361         spinlock_t netlock;
 362 #ifdef CONFIG_HDLC
 363         struct net_device *netdev;
 364 #endif
 365
 366 };
 367
 368 static MGSL_PARAMS default_params = {
 369         .mode            = MGSL_MODE_HDLC,
 370         .loopback        = 0,
 371         .flags           = HDLC_FLAG_UNDERRUN_ABORT15,
 372         .encoding        = HDLC_ENCODING_NRZI_SPACE,
 373         .clock_speed     = 0,
 374         .addr_filter     = 0xff,
 375         .crc_type        = HDLC_CRC_16_CCITT,
 376         .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
 377         .preamble        = HDLC_PREAMBLE_PATTERN_NONE,
 378         .data_rate       = 9600,
 379         .data_bits       = 8,
 380         .stop_bits       = 1,
 381         .parity          = ASYNC_PARITY_NONE
 382 };
 383
 384
 385 #define BH_RECEIVE  1
 386 #define BH_TRANSMIT 2
 387 #define BH_STATUS   4
 388 #define IO_PIN_SHUTDOWN_LIMIT 100
 389
 390 #define DMABUFSIZE 256
 391 #define DESC_LIST_SIZE 4096
 392
 393 #define MASK_PARITY  BIT1
 394 #define MASK_FRAMING BIT2
 395 #define MASK_BREAK   BIT3
 396 #define MASK_OVERRUN BIT4
 397
 398 #define GSR   0x00 /* global status */
 399 #define JCR   0x04 /* JTAG control */
 400 #define IODR  0x08 /* GPIO direction */
 401 #define IOER  0x0c /* GPIO interrupt enable */
 402 #define IOVR  0x10 /* GPIO value */
 403 #define IOSR  0x14 /* GPIO interrupt status */
 404 #define TDR   0x80 /* tx data */
 405 #define RDR   0x80 /* rx data */
 406 #define TCR   0x82 /* tx control */
 407 #define TIR   0x84 /* tx idle */
 408 #define TPR   0x85 /* tx preamble */
 409 #define RCR   0x86 /* rx control */
 410 #define VCR   0x88 /* V.24 control */
 411 #define CCR   0x89 /* clock control */
 412 #define BDR   0x8a /* baud divisor */
 413 #define SCR   0x8c /* serial control */
 414 #define SSR   0x8e /* serial status */
 415 #define RDCSR 0x90 /* rx DMA control/status */
 416 #define TDCSR 0x94 /* tx DMA control/status */
 417 #define RDDAR 0x98 /* rx DMA descriptor address */
 418 #define TDDAR 0x9c /* tx DMA descriptor address */
 419
 420 #define RXIDLE      BIT14
 421 #define RXBREAK     BIT14
 422 #define IRQ_TXDATA  BIT13
 423 #define IRQ_TXIDLE  BIT12
 424 #define IRQ_TXUNDER BIT11 /* HDLC */
 425 #define IRQ_RXDATA  BIT10
 426 #define IRQ_RXIDLE  BIT9  /* HDLC */
 427 #define IRQ_RXBREAK BIT9  /* async */
 428 #define IRQ_RXOVER  BIT8
 429 #define IRQ_DSR     BIT7
 430 #define IRQ_CTS     BIT6
 431 #define IRQ_DCD     BIT5
 432 #define IRQ_RI      BIT4
 433 #define IRQ_ALL     0x3ff0
 434 #define IRQ_MASTER  BIT0
 435
 436 #define slgt_irq_on(info, mask) \
 437         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
 438 #define slgt_irq_off(info, mask) \
 439         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
 440
 441 static __u8  rd_reg8(struct slgt_info *info, unsigned int addr);
 442 static void  wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
 443 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
 444 static void  wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
 445 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
 446 static void  wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
 447
 448 static void  msc_set_vcr(struct slgt_info *info);
 449
 450 static int  startup(struct slgt_info *info);
 451 static int  block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
 452 static void shutdown(struct slgt_info *info);
 453 static void program_hw(struct slgt_info *info);
 454 static void change_params(struct slgt_info *info);
 455
 456 static int  register_test(struct slgt_info *info);
 457 static int  irq_test(struct slgt_info *info);
 458 static int  loopback_test(struct slgt_info *info);
 459 static int  adapter_test(struct slgt_info *info);
 460
 461 static void reset_adapter(struct slgt_info *info);
 462 static void reset_port(struct slgt_info *info);
 463 static void async_mode(struct slgt_info *info);
 464 static void hdlc_mode(struct slgt_info *info);
 465
 466 static void rx_stop(struct slgt_info *info);
 467 static void rx_start(struct slgt_info *info);
 468 static void reset_rbufs(struct slgt_info *info);
 469 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
 470 static void rdma_reset(struct slgt_info *info);
 471 static int  rx_get_frame(struct slgt_info *info);
 472 static int  rx_get_buf(struct slgt_info *info);
 473
 474 static void tx_start(struct slgt_info *info);
 475 static void tx_stop(struct slgt_info *info);
 476 static void tx_set_idle(struct slgt_info *info);
 477 static unsigned int free_tbuf_count(struct slgt_info *info);
 478 static void reset_tbufs(struct slgt_info *info);
 479 static void tdma_reset(struct slgt_info *info);
 480 static void tx_load(struct slgt_info *info, const char *buf, unsigned int count);
 481
 482 static void get_signals(struct slgt_info *info);
 483 static void set_signals(struct slgt_info *info);
 484 static void enable_loopback(struct slgt_info *info);
 485 static void set_rate(struct slgt_info *info, u32 data_rate);
 486
 487 static int  bh_action(struct slgt_info *info);
 488 static void bh_handler(void* context);
 489 static void bh_transmit(struct slgt_info *info);
 490 static void isr_serial(struct slgt_info *info);
 491 static void isr_rdma(struct slgt_info *info);
 492 static void isr_txeom(struct slgt_info *info, unsigned short status);
 493 static void isr_tdma(struct slgt_info *info);
 494 static irqreturn_t slgt_interrupt(int irq, void *dev_id, struct pt_regs * regs);
 495
 496 static int  alloc_dma_bufs(struct slgt_info *info);
 497 static void free_dma_bufs(struct slgt_info *info);
 498 static int  alloc_desc(struct slgt_info *info);
 499 static void free_desc(struct slgt_info *info);
 500 static int  alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 501 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 502
 503 static int  alloc_tmp_rbuf(struct slgt_info *info);
 504 static void free_tmp_rbuf(struct slgt_info *info);
 505
 506 static void tx_timeout(unsigned long context);
 507 static void rx_timeout(unsigned long context);
 508
 509 /*
 510  * ioctl handlers
 511  */
 512 static int  get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
 513 static int  get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 514 static int  set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 515 static int  get_txidle(struct slgt_info *info, int __user *idle_mode);
 516 static int  set_txidle(struct slgt_info *info, int idle_mode);
 517 static int  tx_enable(struct slgt_info *info, int enable);
 518 static int  tx_abort(struct slgt_info *info);
 519 static int  rx_enable(struct slgt_info *info, int enable);
 520 static int  modem_input_wait(struct slgt_info *info,int arg);
 521 static int  wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
 522 static int  tiocmget(struct tty_struct *tty, struct file *file);
 523 static int  tiocmset(struct tty_struct *tty, struct file *file,
 524                      unsigned int set, unsigned int clear);
 525 static void set_break(struct tty_struct *tty, int break_state);
 526 static int  get_interface(struct slgt_info *info, int __user *if_mode);
 527 static int  set_interface(struct slgt_info *info, int if_mode);
 528 static int  set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 529 static int  get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 530 static int  wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 531
 532 /*
 533  * driver functions
 534  */
 535 static void add_device(struct slgt_info *info);
 536 static void device_init(int adapter_num, struct pci_dev *pdev);
 537 static int  claim_resources(struct slgt_info *info);
 538 static void release_resources(struct slgt_info *info);
 539
 540 /*
 541  * DEBUG OUTPUT CODE
 542  */
 543 #ifndef DBGINFO
 544 #define DBGINFO(fmt)
 545 #endif
 546 #ifndef DBGERR
 547 #define DBGERR(fmt)
 548 #endif
 549 #ifndef DBGBH
 550 #define DBGBH(fmt)
 551 #endif
 552 #ifndef DBGISR
 553 #define DBGISR(fmt)
 554 #endif
 555
 556 #ifdef DBGDATA
 557 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
 558 {
 559         int i;
 560         int linecount;
 561         printk("%s %s data:\n",info->device_name, label);
 562         while(count) {
 563                 linecount = (count > 16) ? 16 : count;
 564                 for(i=0; i < linecount; i++)
 565                         printk("%02X ",(unsigned char)data[i]);
 566                 for(;i<17;i++)
 567                         printk("   ");
 568                 for(i=0;i<linecount;i++) {
 569                         if (data[i]>=040 && data[i]<=0176)
 570                                 printk("%c",data[i]);
 571                         else
 572                                 printk(".");
 573                 }
 574                 printk("\n");
 575                 data  += linecount;
 576                 count -= linecount;
 577         }
 578 }
 579 #else
 580 #define DBGDATA(info, buf, size, label)
 581 #endif
 582
 583 #ifdef DBGTBUF
 584 static void dump_tbufs(struct slgt_info *info)
 585 {
 586         int i;
 587         printk("tbuf_current=%d\n", info->tbuf_current);
 588         for (i=0 ; i < info->tbuf_count ; i++) {
 589                 printk("%d: count=%04X status=%04X\n",
 590                         i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
 591         }
 592 }
 593 #else
 594 #define DBGTBUF(info)
 595 #endif
 596
 597 #ifdef DBGRBUF
 598 static void dump_rbufs(struct slgt_info *info)
 599 {
 600         int i;
 601         printk("rbuf_current=%d\n", info->rbuf_current);
 602         for (i=0 ; i < info->rbuf_count ; i++) {
 603                 printk("%d: count=%04X status=%04X\n",
 604                         i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
 605         }
 606 }
 607 #else
 608 #define DBGRBUF(info)
 609 #endif
 610
 611 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
 612 {
 613 #ifdef SANITY_CHECK
 614         if (!info) {
 615                 printk("null struct slgt_info for (%s) in %s\n", devname, name);
 616                 return 1;
 617         }
 618         if (info->magic != MGSL_MAGIC) {
 619                 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
 620                 return 1;
 621         }
 622 #else
 623         if (!info)
 624                 return 1;
 625 #endif
 626         return 0;
 627 }
 628
 629 /**
 630  * line discipline callback wrappers
 631  *
 632  * The wrappers maintain line discipline references
 633  * while calling into the line discipline.
 634  *
 635  * ldisc_receive_buf  - pass receive data to line discipline
 636  */
 637 static void ldisc_receive_buf(struct tty_struct *tty,
 638                               const __u8 *data, char *flags, int count)
 639 {
 640         struct tty_ldisc *ld;
 641         if (!tty)
 642                 return;
 643         ld = tty_ldisc_ref(tty);
 644         if (ld) {
 645                 if (ld->receive_buf)
 646                         ld->receive_buf(tty, data, flags, count);
 647                 tty_ldisc_deref(ld);
 648         }
 649 }
 650
 651 /* tty callbacks */
 652
 653 static int open(struct tty_struct *tty, struct file *filp)
 654 {
 655         struct slgt_info *info;
 656         int retval, line;
 657         unsigned long flags;
 658
 659         line = tty->index;
 660         if ((line < 0) || (line >= slgt_device_count)) {
 661                 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
 662                 return -ENODEV;
 663         }
 664
 665         info = slgt_device_list;
 666         while(info && info->line != line)
 667                 info = info->next_device;
 668         if (sanity_check(info, tty->name, "open"))
 669                 return -ENODEV;
 670         if (info->init_error) {
 671                 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
 672                 return -ENODEV;
 673         }
 674
 675         tty->driver_data = info;
 676         info->tty = tty;
 677
 678         DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->count));
 679
 680         /* If port is closing, signal caller to try again */
 681         if (tty_hung_up_p(filp) || info->flags & ASYNC_CLOSING){
 682                 if (info->flags & ASYNC_CLOSING)
 683                         interruptible_sleep_on(&info->close_wait);
 684                 retval = ((info->flags & ASYNC_HUP_NOTIFY) ?
 685                         -EAGAIN : -ERESTARTSYS);
 686                 goto cleanup;
 687         }
 688
 689         info->tty->low_latency = (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 690
 691         spin_lock_irqsave(&info->netlock, flags);
 692         if (info->netcount) {
 693                 retval = -EBUSY;
 694                 spin_unlock_irqrestore(&info->netlock, flags);
 695                 goto cleanup;
 696         }
 697         info->count++;
 698         spin_unlock_irqrestore(&info->netlock, flags);
 699
 700         if (info->count == 1) {
 701                 /* 1st open on this device, init hardware */
 702                 retval = startup(info);
 703                 if (retval < 0)
 704                         goto cleanup;
 705         }
 706
 707         retval = block_til_ready(tty, filp, info);
 708         if (retval) {
 709                 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
 710                 goto cleanup;
 711         }
 712
 713         retval = 0;
 714
 715 cleanup:
 716         if (retval) {
 717                 if (tty->count == 1)
 718                         info->tty = NULL; /* tty layer will release tty struct */
 719                 if(info->count)
 720                         info->count--;
 721         }
 722
 723         DBGINFO(("%s open rc=%d\n", info->device_name, retval));
 724         return retval;
 725 }
 726
 727 static void close(struct tty_struct *tty, struct file *filp)
 728 {
 729         struct slgt_info *info = tty->driver_data;
 730
 731         if (sanity_check(info, tty->name, "close"))
 732                 return;
 733         DBGINFO(("%s close entry, count=%d\n", info->device_name, info->count));
 734
 735         if (!info->count)
 736                 return;
 737
 738         if (tty_hung_up_p(filp))
 739                 goto cleanup;
 740
 741         if ((tty->count == 1) && (info->count != 1)) {
 742                 /*
 743                  * tty->count is 1 and the tty structure will be freed.
 744                  * info->count should be one in this case.
 745                  * if it's not, correct it so that the port is shutdown.
 746                  */
 747                 DBGERR(("%s close: bad refcount; tty->count=1, "
 748                        "info->count=%d\n", info->device_name, info->count));
 749                 info->count = 1;
 750         }
 751
 752         info->count--;
 753
 754         /* if at least one open remaining, leave hardware active */
 755         if (info->count)
 756                 goto cleanup;
 757
 758         info->flags |= ASYNC_CLOSING;
 759
 760         /* set tty->closing to notify line discipline to
 761          * only process XON/XOFF characters. Only the N_TTY
 762          * discipline appears to use this (ppp does not).
 763          */
 764         tty->closing = 1;
 765
 766         /* wait for transmit data to clear all layers */
 767
 768         if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE) {
 769                 DBGINFO(("%s call tty_wait_until_sent\n", info->device_name));
 770                 tty_wait_until_sent(tty, info->closing_wait);
 771         }
 772
 773         if (info->flags & ASYNC_INITIALIZED)
 774                 wait_until_sent(tty, info->timeout);
 775         if (tty->driver->flush_buffer)
 776                 tty->driver->flush_buffer(tty);
 777         tty_ldisc_flush(tty);
 778
 779         shutdown(info);
 780
 781         tty->closing = 0;
 782         info->tty = NULL;
 783
 784         if (info->blocked_open) {
 785                 if (info->close_delay) {
 786                         msleep_interruptible(jiffies_to_msecs(info->close_delay));
 787                 }
 788                 wake_up_interruptible(&info->open_wait);
 789         }
 790
 791         info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
 792
 793         wake_up_interruptible(&info->close_wait);
 794
 795 cleanup:
 796         DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->count));
 797 }
 798
 799 static void hangup(struct tty_struct *tty)
 800 {
 801         struct slgt_info *info = tty->driver_data;
 802
 803         if (sanity_check(info, tty->name, "hangup"))
 804                 return;
 805         DBGINFO(("%s hangup\n", info->device_name));
 806
 807         flush_buffer(tty);
 808         shutdown(info);
 809
 810         info->count = 0;
 811         info->flags &= ~ASYNC_NORMAL_ACTIVE;
 812         info->tty = NULL;
 813
 814         wake_up_interruptible(&info->open_wait);
 815 }
 816
 817 static void set_termios(struct tty_struct *tty, struct termios *old_termios)
 818 {
 819         struct slgt_info *info = tty->driver_data;
 820         unsigned long flags;
 821
 822         DBGINFO(("%s set_termios\n", tty->driver->name));
 823
 824         /* just return if nothing has changed */
 825         if ((tty->termios->c_cflag == old_termios->c_cflag)
 826             && (RELEVANT_IFLAG(tty->termios->c_iflag)
 827                 == RELEVANT_IFLAG(old_termios->c_iflag)))
 828                 return;
 829
 830         change_params(info);
 831
 832         /* Handle transition to B0 status */
 833         if (old_termios->c_cflag & CBAUD &&
 834             !(tty->termios->c_cflag & CBAUD)) {
 835                 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
 836                 spin_lock_irqsave(&info->lock,flags);
 837                 set_signals(info);
 838                 spin_unlock_irqrestore(&info->lock,flags);
 839         }
 840
 841         /* Handle transition away from B0 status */
 842         if (!(old_termios->c_cflag & CBAUD) &&
 843             tty->termios->c_cflag & CBAUD) {
 844                 info->signals |= SerialSignal_DTR;
 845                 if (!(tty->termios->c_cflag & CRTSCTS) ||
 846                     !test_bit(TTY_THROTTLED, &tty->flags)) {
 847                         info->signals |= SerialSignal_RTS;
 848                 }
 849                 spin_lock_irqsave(&info->lock,flags);
 850                 set_signals(info);
 851                 spin_unlock_irqrestore(&info->lock,flags);
 852         }
 853
 854         /* Handle turning off CRTSCTS */
 855         if (old_termios->c_cflag & CRTSCTS &&
 856             !(tty->termios->c_cflag & CRTSCTS)) {
 857                 tty->hw_stopped = 0;
 858                 tx_release(tty);
 859         }
 860 }
 861
 862 static int write(struct tty_struct *tty,
 863                  const unsigned char *buf, int count)
 864 {
 865         int ret = 0;
 866         struct slgt_info *info = tty->driver_data;
 867         unsigned long flags;
 868
 869         if (sanity_check(info, tty->name, "write"))
 870                 goto cleanup;
 871         DBGINFO(("%s write count=%d\n", info->device_name, count));
 872
 873         if (!tty || !info->tx_buf)
 874                 goto cleanup;
 875
 876         if (count > info->max_frame_size) {
 877                 ret = -EIO;
 878                 goto cleanup;
 879         }
 880
 881         if (!count)
 882                 goto cleanup;
 883
 884         if (info->params.mode == MGSL_MODE_RAW) {
 885                 unsigned int bufs_needed = (count/DMABUFSIZE);
 886                 unsigned int bufs_free = free_tbuf_count(info);
 887                 if (count % DMABUFSIZE)
 888                         ++bufs_needed;
 889                 if (bufs_needed > bufs_free)
 890                         goto cleanup;
 891         } else {
 892                 if (info->tx_active)
 893                         goto cleanup;
 894                 if (info->tx_count) {
 895                         /* send accumulated data from send_char() calls */
 896                         /* as frame and wait before accepting more data. */
 897                         tx_load(info, info->tx_buf, info->tx_count);
 898                         goto start;
 899                 }
 900         }
 901
 902         ret = info->tx_count = count;
 903         tx_load(info, buf, count);
 904         goto start;
 905
 906 start:
 907         if (info->tx_count && !tty->stopped && !tty->hw_stopped) {
 908                 spin_lock_irqsave(&info->lock,flags);
 909                 if (!info->tx_active)
 910                         tx_start(info);
 911                 spin_unlock_irqrestore(&info->lock,flags);
 912         }
 913
 914 cleanup:
 915         DBGINFO(("%s write rc=%d\n", info->device_name, ret));
 916         return ret;
 917 }
 918
 919 static void put_char(struct tty_struct *tty, unsigned char ch)
 920 {
 921         struct slgt_info *info = tty->driver_data;
 922         unsigned long flags;
 923
 924         if (sanity_check(info, tty->name, "put_char"))
 925                 return;
 926         DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
 927         if (!tty || !info->tx_buf)
 928                 return;
 929         spin_lock_irqsave(&info->lock,flags);
 930         if (!info->tx_active && (info->tx_count < info->max_frame_size))
 931                 info->tx_buf[info->tx_count++] = ch;
 932         spin_unlock_irqrestore(&info->lock,flags);
 933 }
 934
 935 static void send_xchar(struct tty_struct *tty, char ch)
 936 {
 937         struct slgt_info *info = tty->driver_data;
 938         unsigned long flags;
 939
 940         if (sanity_check(info, tty->name, "send_xchar"))
 941                 return;
 942         DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
 943         info->x_char = ch;
 944         if (ch) {
 945                 spin_lock_irqsave(&info->lock,flags);
 946                 if (!info->tx_enabled)
 947                         tx_start(info);
 948                 spin_unlock_irqrestore(&info->lock,flags);
 949         }
 950 }
 951
 952 static void wait_until_sent(struct tty_struct *tty, int timeout)
 953 {
 954         struct slgt_info *info = tty->driver_data;
 955         unsigned long orig_jiffies, char_time;
 956
 957         if (!info )
 958                 return;
 959         if (sanity_check(info, tty->name, "wait_until_sent"))
 960                 return;
 961         DBGINFO(("%s wait_until_sent entry\n", info->device_name));
 962         if (!(info->flags & ASYNC_INITIALIZED))
 963                 goto exit;
 964
 965         orig_jiffies = jiffies;
 966
 967         /* Set check interval to 1/5 of estimated time to
 968          * send a character, and make it at least 1. The check
 969          * interval should also be less than the timeout.
 970          * Note: use tight timings here to satisfy the NIST-PCTS.
 971          */
 972
 973         if (info->params.data_rate) {
 974                 char_time = info->timeout/(32 * 5);
 975                 if (!char_time)
 976                         char_time++;
 977         } else
 978                 char_time = 1;
 979
 980         if (timeout)
 981                 char_time = min_t(unsigned long, char_time, timeout);
 982
 983         while (info->tx_active) {
 984                 msleep_interruptible(jiffies_to_msecs(char_time));
 985                 if (signal_pending(current))
 986                         break;
 987                 if (timeout && time_after(jiffies, orig_jiffies + timeout))
 988                         break;
 989         }
 990
 991 exit:
 992         DBGINFO(("%s wait_until_sent exit\n", info->device_name));
 993 }
 994
 995 static int write_room(struct tty_struct *tty)
 996 {
 997         struct slgt_info *info = tty->driver_data;
 998         int ret;
 999
1000         if (sanity_check(info, tty->name, "write_room"))
1001                 return 0;
1002         ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
1003         DBGINFO(("%s write_room=%d\n", info->device_name, ret));
1004         return ret;
1005 }
1006
1007 static void flush_chars(struct tty_struct *tty)
1008 {
1009         struct slgt_info *info = tty->driver_data;
1010         unsigned long flags;
1011
1012         if (sanity_check(info, tty->name, "flush_chars"))
1013                 return;
1014         DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
1015
1016         if (info->tx_count <= 0 || tty->stopped ||
1017             tty->hw_stopped || !info->tx_buf)
1018                 return;
1019
1020         DBGINFO(("%s flush_chars start transmit\n", info->device_name));
1021
1022         spin_lock_irqsave(&info->lock,flags);
1023         if (!info->tx_active && info->tx_count) {
1024                 tx_load(info, info->tx_buf,info->tx_count);
1025                 tx_start(info);
1026         }
1027         spin_unlock_irqrestore(&info->lock,flags);
1028 }
1029
1030 static void flush_buffer(struct tty_struct *tty)
1031 {
1032         struct slgt_info *info = tty->driver_data;
1033         unsigned long flags;
1034
1035         if (sanity_check(info, tty->name, "flush_buffer"))
1036                 return;
1037         DBGINFO(("%s flush_buffer\n", info->device_name));
1038
1039         spin_lock_irqsave(&info->lock,flags);
1040         if (!info->tx_active)
1041                 info->tx_count = 0;
1042         spin_unlock_irqrestore(&info->lock,flags);
1043
1044         wake_up_interruptible(&tty->write_wait);
1045         tty_wakeup(tty);
1046 }
1047
1048 /*
1049  * throttle (stop) transmitter
1050  */
1051 static void tx_hold(struct tty_struct *tty)
1052 {
1053         struct slgt_info *info = tty->driver_data;
1054         unsigned long flags;
1055
1056         if (sanity_check(info, tty->name, "tx_hold"))
1057                 return;
1058         DBGINFO(("%s tx_hold\n", info->device_name));
1059         spin_lock_irqsave(&info->lock,flags);
1060         if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
1061                 tx_stop(info);
1062         spin_unlock_irqrestore(&info->lock,flags);
1063 }
1064
1065 /*
1066  * release (start) transmitter
1067  */
1068 static void tx_release(struct tty_struct *tty)
1069 {
1070         struct slgt_info *info = tty->driver_data;
1071         unsigned long flags;
1072
1073         if (sanity_check(info, tty->name, "tx_release"))
1074                 return;
1075         DBGINFO(("%s tx_release\n", info->device_name));
1076         spin_lock_irqsave(&info->lock,flags);
1077         if (!info->tx_active && info->tx_count) {
1078                 tx_load(info, info->tx_buf, info->tx_count);
1079                 tx_start(info);
1080         }
1081         spin_unlock_irqrestore(&info->lock,flags);
1082 }
1083
1084 /*
1085  * Service an IOCTL request
1086  *
1087  * Arguments
1088  *
1089  *      tty     pointer to tty instance data
1090  *      file    pointer to associated file object for device
1091  *      cmd     IOCTL command code
1092  *      arg     command argument/context
1093  *
1094  * Return 0 if success, otherwise error code
1095  */
1096 static int ioctl(struct tty_struct *tty, struct file *file,
1097                  unsigned int cmd, unsigned long arg)
1098 {
1099         struct slgt_info *info = tty->driver_data;
1100         struct mgsl_icount cnow;        /* kernel counter temps */
1101         struct serial_icounter_struct __user *p_cuser;  /* user space */
1102         unsigned long flags;
1103         void __user *argp = (void __user *)arg;
1104
1105         if (sanity_check(info, tty->name, "ioctl"))
1106                 return -ENODEV;
1107         DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1108
1109         if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1110             (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
1111                 if (tty->flags & (1 << TTY_IO_ERROR))
1112                     return -EIO;
1113         }
1114
1115         switch (cmd) {
1116         case MGSL_IOCGPARAMS:
1117                 return get_params(info, argp);
1118         case MGSL_IOCSPARAMS:
1119                 return set_params(info, argp);
1120         case MGSL_IOCGTXIDLE:
1121                 return get_txidle(info, argp);
1122         case MGSL_IOCSTXIDLE:
1123                 return set_txidle(info, (int)arg);
1124         case MGSL_IOCTXENABLE:
1125                 return tx_enable(info, (int)arg);
1126         case MGSL_IOCRXENABLE:
1127                 return rx_enable(info, (int)arg);
1128         case MGSL_IOCTXABORT:
1129                 return tx_abort(info);
1130         case MGSL_IOCGSTATS:
1131                 return get_stats(info, argp);
1132         case MGSL_IOCWAITEVENT:
1133                 return wait_mgsl_event(info, argp);
1134         case TIOCMIWAIT:
1135                 return modem_input_wait(info,(int)arg);
1136         case MGSL_IOCGIF:
1137                 return get_interface(info, argp);
1138         case MGSL_IOCSIF:
1139                 return set_interface(info,(int)arg);
1140         case MGSL_IOCSGPIO:
1141                 return set_gpio(info, argp);
1142         case MGSL_IOCGGPIO:
1143                 return get_gpio(info, argp);
1144         case MGSL_IOCWAITGPIO:
1145                 return wait_gpio(info, argp);
1146         case TIOCGICOUNT:
1147                 spin_lock_irqsave(&info->lock,flags);
1148                 cnow = info->icount;
1149                 spin_unlock_irqrestore(&info->lock,flags);
1150                 p_cuser = argp;
1151                 if (put_user(cnow.cts, &p_cuser->cts) ||
1152                     put_user(cnow.dsr, &p_cuser->dsr) ||
1153                     put_user(cnow.rng, &p_cuser->rng) ||
1154                     put_user(cnow.dcd, &p_cuser->dcd) ||
1155                     put_user(cnow.rx, &p_cuser->rx) ||
1156                     put_user(cnow.tx, &p_cuser->tx) ||
1157                     put_user(cnow.frame, &p_cuser->frame) ||
1158                     put_user(cnow.overrun, &p_cuser->overrun) ||
1159                     put_user(cnow.parity, &p_cuser->parity) ||
1160                     put_user(cnow.brk, &p_cuser->brk) ||
1161                     put_user(cnow.buf_overrun, &p_cuser->buf_overrun))
1162                         return -EFAULT;
1163                 return 0;
1164         default:
1165                 return -ENOIOCTLCMD;
1166         }
1167         return 0;
1168 }
1169
1170 /*
1171  * proc fs support
1172  */
1173 static inline int line_info(char *buf, struct slgt_info *info)
1174 {
1175         char stat_buf[30];
1176         int ret;
1177         unsigned long flags;
1178
1179         ret = sprintf(buf, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1180                       info->device_name, info->phys_reg_addr,
1181                       info->irq_level, info->max_frame_size);
1182
1183         /* output current serial signal states */
1184         spin_lock_irqsave(&info->lock,flags);
1185         get_signals(info);
1186         spin_unlock_irqrestore(&info->lock,flags);
1187
1188         stat_buf[0] = 0;
1189         stat_buf[1] = 0;
1190         if (info->signals & SerialSignal_RTS)
1191                 strcat(stat_buf, "|RTS");
1192         if (info->signals & SerialSignal_CTS)
1193                 strcat(stat_buf, "|CTS");
1194         if (info->signals & SerialSignal_DTR)
1195                 strcat(stat_buf, "|DTR");
1196         if (info->signals & SerialSignal_DSR)
1197                 strcat(stat_buf, "|DSR");
1198         if (info->signals & SerialSignal_DCD)
1199                 strcat(stat_buf, "|CD");
1200         if (info->signals & SerialSignal_RI)
1201                 strcat(stat_buf, "|RI");
1202
1203         if (info->params.mode != MGSL_MODE_ASYNC) {
1204                 ret += sprintf(buf+ret, "\tHDLC txok:%d rxok:%d",
1205                                info->icount.txok, info->icount.rxok);
1206                 if (info->icount.txunder)
1207                         ret += sprintf(buf+ret, " txunder:%d", info->icount.txunder);
1208                 if (info->icount.txabort)
1209                         ret += sprintf(buf+ret, " txabort:%d", info->icount.txabort);
1210                 if (info->icount.rxshort)
1211                         ret += sprintf(buf+ret, " rxshort:%d", info->icount.rxshort);
1212                 if (info->icount.rxlong)
1213                         ret += sprintf(buf+ret, " rxlong:%d", info->icount.rxlong);
1214                 if (info->icount.rxover)
1215                         ret += sprintf(buf+ret, " rxover:%d", info->icount.rxover);
1216                 if (info->icount.rxcrc)
1217                         ret += sprintf(buf+ret, " rxcrc:%d", info->icount.rxcrc);
1218         } else {
1219                 ret += sprintf(buf+ret, "\tASYNC tx:%d rx:%d",
1220                                info->icount.tx, info->icount.rx);
1221                 if (info->icount.frame)
1222                         ret += sprintf(buf+ret, " fe:%d", info->icount.frame);
1223                 if (info->icount.parity)
1224                         ret += sprintf(buf+ret, " pe:%d", info->icount.parity);
1225                 if (info->icount.brk)
1226                         ret += sprintf(buf+ret, " brk:%d", info->icount.brk);
1227                 if (info->icount.overrun)
1228                         ret += sprintf(buf+ret, " oe:%d", info->icount.overrun);
1229         }
1230
1231         /* Append serial signal status to end */
1232         ret += sprintf(buf+ret, " %s\n", stat_buf+1);
1233
1234         ret += sprintf(buf+ret, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1235                        info->tx_active,info->bh_requested,info->bh_running,
1236                        info->pending_bh);
1237
1238         return ret;
1239 }
1240
1241 /* Called to print information about devices
1242  */
1243 static int read_proc(char *page, char **start, off_t off, int count,
1244                      int *eof, void *data)
1245 {
1246         int len = 0, l;
1247         off_t   begin = 0;
1248         struct slgt_info *info;
1249
1250         len += sprintf(page, "synclink_gt driver:%s\n", driver_version);
1251
1252         info = slgt_device_list;
1253         while( info ) {
1254                 l = line_info(page + len, info);
1255                 len += l;
1256                 if (len+begin > off+count)
1257                         goto done;
1258                 if (len+begin < off) {
1259                         begin += len;
1260                         len = 0;
1261                 }
1262                 info = info->next_device;
1263         }
1264
1265         *eof = 1;
1266 done:
1267         if (off >= len+begin)
1268                 return 0;
1269         *start = page + (off-begin);
1270         return ((count < begin+len-off) ? count : begin+len-off);
1271 }
1272
1273 /*
1274  * return count of bytes in transmit buffer
1275  */
1276 static int chars_in_buffer(struct tty_struct *tty)
1277 {
1278         struct slgt_info *info = tty->driver_data;
1279         if (sanity_check(info, tty->name, "chars_in_buffer"))
1280                 return 0;
1281         DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, info->tx_count));
1282         return info->tx_count;
1283 }
1284
1285 /*
1286  * signal remote device to throttle send data (our receive data)
1287  */
1288 static void throttle(struct tty_struct * tty)
1289 {
1290         struct slgt_info *info = tty->driver_data;
1291         unsigned long flags;
1292
1293         if (sanity_check(info, tty->name, "throttle"))
1294                 return;
1295         DBGINFO(("%s throttle\n", info->device_name));
1296         if (I_IXOFF(tty))
1297                 send_xchar(tty, STOP_CHAR(tty));
1298         if (tty->termios->c_cflag & CRTSCTS) {
1299                 spin_lock_irqsave(&info->lock,flags);
1300                 info->signals &= ~SerialSignal_RTS;
1301                 set_signals(info);
1302                 spin_unlock_irqrestore(&info->lock,flags);
1303         }
1304 }
1305
1306 /*
1307  * signal remote device to stop throttling send data (our receive data)
1308  */
1309 static void unthrottle(struct tty_struct * tty)
1310 {
1311         struct slgt_info *info = tty->driver_data;
1312         unsigned long flags;
1313
1314         if (sanity_check(info, tty->name, "unthrottle"))
1315                 return;
1316         DBGINFO(("%s unthrottle\n", info->device_name));
1317         if (I_IXOFF(tty)) {
1318                 if (info->x_char)
1319                         info->x_char = 0;
1320                 else
1321                         send_xchar(tty, START_CHAR(tty));
1322         }
1323         if (tty->termios->c_cflag & CRTSCTS) {
1324                 spin_lock_irqsave(&info->lock,flags);
1325                 info->signals |= SerialSignal_RTS;
1326                 set_signals(info);
1327                 spin_unlock_irqrestore(&info->lock,flags);
1328         }
1329 }
1330
1331 /*
1332  * set or clear transmit break condition
1333  * break_state  -1=set break condition, 0=clear
1334  */
1335 static void set_break(struct tty_struct *tty, int break_state)
1336 {
1337         struct slgt_info *info = tty->driver_data;
1338         unsigned short value;
1339         unsigned long flags;
1340
1341         if (sanity_check(info, tty->name, "set_break"))
1342                 return;
1343         DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1344
1345         spin_lock_irqsave(&info->lock,flags);
1346         value = rd_reg16(info, TCR);
1347         if (break_state == -1)
1348                 value |= BIT6;
1349         else
1350                 value &= ~BIT6;
1351         wr_reg16(info, TCR, value);
1352         spin_unlock_irqrestore(&info->lock,flags);
1353 }
1354
1355 #ifdef CONFIG_HDLC
1356
1357 /**
1358  * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1359  * set encoding and frame check sequence (FCS) options
1360  *
1361  * dev       pointer to network device structure
1362  * encoding  serial encoding setting
1363  * parity    FCS setting
1364  *
1365  * returns 0 if success, otherwise error code
1366  */
1367 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1368                           unsigned short parity)
1369 {
1370         struct slgt_info *info = dev_to_port(dev);
1371         unsigned char  new_encoding;
1372         unsigned short new_crctype;
1373
1374         /* return error if TTY interface open */
1375         if (info->count)
1376                 return -EBUSY;
1377
1378         DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1379
1380         switch (encoding)
1381         {
1382         case ENCODING_NRZ:        new_encoding = HDLC_ENCODING_NRZ; break;
1383         case ENCODING_NRZI:       new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1384         case ENCODING_FM_MARK:    new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1385         case ENCODING_FM_SPACE:   new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1386         case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1387         default: return -EINVAL;
1388         }
1389
1390         switch (parity)
1391         {
1392         case PARITY_NONE:            new_crctype = HDLC_CRC_NONE; break;
1393         case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1394         case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1395         default: return -EINVAL;
1396         }
1397
1398         info->params.encoding = new_encoding;
1399         info->params.crc_type = new_crctype;
1400
1401         /* if network interface up, reprogram hardware */
1402         if (info->netcount)
1403                 program_hw(info);
1404
1405         return 0;
1406 }
1407
1408 /**
1409  * called by generic HDLC layer to send frame
1410  *
1411  * skb  socket buffer containing HDLC frame
1412  * dev  pointer to network device structure
1413  *
1414  * returns 0 if success, otherwise error code
1415  */
1416 static int hdlcdev_xmit(struct sk_buff *skb, struct net_device *dev)
1417 {
1418         struct slgt_info *info = dev_to_port(dev);
1419         struct net_device_stats *stats = hdlc_stats(dev);
1420         unsigned long flags;
1421
1422         DBGINFO(("%s hdlc_xmit\n", dev->name));
1423
1424         /* stop sending until this frame completes */
1425         netif_stop_queue(dev);
1426
1427         /* copy data to device buffers */
1428         info->tx_count = skb->len;
1429         tx_load(info, skb->data, skb->len);
1430
1431         /* update network statistics */
1432         stats->tx_packets++;
1433         stats->tx_bytes += skb->len;
1434
1435         /* done with socket buffer, so free it */
1436         dev_kfree_skb(skb);
1437
1438         /* save start time for transmit timeout detection */
1439         dev->trans_start = jiffies;
1440
1441         /* start hardware transmitter if necessary */
1442         spin_lock_irqsave(&info->lock,flags);
1443         if (!info->tx_active)
1444                 tx_start(info);
1445         spin_unlock_irqrestore(&info->lock,flags);
1446
1447         return 0;
1448 }
1449
1450 /**
1451  * called by network layer when interface enabled
1452  * claim resources and initialize hardware
1453  *
1454  * dev  pointer to network device structure
1455  *
1456  * returns 0 if success, otherwise error code
1457  */
1458 static int hdlcdev_open(struct net_device *dev)
1459 {
1460         struct slgt_info *info = dev_to_port(dev);
1461         int rc;
1462         unsigned long flags;
1463
1464         DBGINFO(("%s hdlcdev_open\n", dev->name));
1465
1466         /* generic HDLC layer open processing */
1467         if ((rc = hdlc_open(dev)))
1468                 return rc;
1469
1470         /* arbitrate between network and tty opens */
1471         spin_lock_irqsave(&info->netlock, flags);
1472         if (info->count != 0 || info->netcount != 0) {
1473                 DBGINFO(("%s hdlc_open busy\n", dev->name));
1474                 spin_unlock_irqrestore(&info->netlock, flags);
1475                 return -EBUSY;
1476         }
1477         info->netcount=1;
1478         spin_unlock_irqrestore(&info->netlock, flags);
1479
1480         /* claim resources and init adapter */
1481         if ((rc = startup(info)) != 0) {
1482                 spin_lock_irqsave(&info->netlock, flags);
1483                 info->netcount=0;
1484                 spin_unlock_irqrestore(&info->netlock, flags);
1485                 return rc;
1486         }
1487
1488         /* assert DTR and RTS, apply hardware settings */
1489         info->signals |= SerialSignal_RTS + SerialSignal_DTR;
1490         program_hw(info);
1491
1492         /* enable network layer transmit */
1493         dev->trans_start = jiffies;
1494         netif_start_queue(dev);
1495
1496         /* inform generic HDLC layer of current DCD status */
1497         spin_lock_irqsave(&info->lock, flags);
1498         get_signals(info);
1499         spin_unlock_irqrestore(&info->lock, flags);
1500         hdlc_set_carrier(info->signals & SerialSignal_DCD, dev);
1501
1502         return 0;
1503 }
1504
1505 /**
1506  * called by network layer when interface is disabled
1507  * shutdown hardware and release resources
1508  *
1509  * dev  pointer to network device structure
1510  *
1511  * returns 0 if success, otherwise error code
1512  */
1513 static int hdlcdev_close(struct net_device *dev)
1514 {
1515         struct slgt_info *info = dev_to_port(dev);
1516         unsigned long flags;
1517
1518         DBGINFO(("%s hdlcdev_close\n", dev->name));
1519
1520         netif_stop_queue(dev);
1521
1522         /* shutdown adapter and release resources */
1523         shutdown(info);
1524
1525         hdlc_close(dev);
1526
1527         spin_lock_irqsave(&info->netlock, flags);
1528         info->netcount=0;
1529         spin_unlock_irqrestore(&info->netlock, flags);
1530
1531         return 0;
1532 }
1533
1534 /**
1535  * called by network layer to process IOCTL call to network device
1536  *
1537  * dev  pointer to network device structure
1538  * ifr  pointer to network interface request structure
1539  * cmd  IOCTL command code
1540  *
1541  * returns 0 if success, otherwise error code
1542  */
1543 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1544 {
1545         const size_t size = sizeof(sync_serial_settings);
1546         sync_serial_settings new_line;
1547         sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1548         struct slgt_info *info = dev_to_port(dev);
1549         unsigned int flags;
1550
1551         DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1552
1553         /* return error if TTY interface open */
1554         if (info->count)
1555                 return -EBUSY;
1556
1557         if (cmd != SIOCWANDEV)
1558                 return hdlc_ioctl(dev, ifr, cmd);
1559
1560         switch(ifr->ifr_settings.type) {
1561         case IF_GET_IFACE: /* return current sync_serial_settings */
1562
1563                 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1564                 if (ifr->ifr_settings.size < size) {
1565                         ifr->ifr_settings.size = size; /* data size wanted */
1566                         return -ENOBUFS;
1567                 }
1568
1569                 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1570                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1571                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1572                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1573
1574                 switch (flags){
1575                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1576                 case (HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_INT; break;
1577                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_TXINT; break;
1578                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1579                 default: new_line.clock_type = CLOCK_DEFAULT;
1580                 }
1581
1582                 new_line.clock_rate = info->params.clock_speed;
1583                 new_line.loopback   = info->params.loopback ? 1:0;
1584
1585                 if (copy_to_user(line, &new_line, size))
1586                         return -EFAULT;
1587                 return 0;
1588
1589         case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1590
1591                 if(!capable(CAP_NET_ADMIN))
1592                         return -EPERM;
1593                 if (copy_from_user(&new_line, line, size))
1594                         return -EFAULT;
1595
1596                 switch (new_line.clock_type)
1597                 {
1598                 case CLOCK_EXT:      flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1599                 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1600                 case CLOCK_INT:      flags = HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG;    break;
1601                 case CLOCK_TXINT:    flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG;    break;
1602                 case CLOCK_DEFAULT:  flags = info->params.flags &
1603                                              (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1604                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1605                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1606                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN); break;
1607                 default: return -EINVAL;
1608                 }
1609
1610                 if (new_line.loopback != 0 && new_line.loopback != 1)
1611                         return -EINVAL;
1612
1613                 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1614                                         HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1615                                         HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1616                                         HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1617                 info->params.flags |= flags;
1618
1619                 info->params.loopback = new_line.loopback;
1620
1621                 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1622                         info->params.clock_speed = new_line.clock_rate;
1623                 else
1624                         info->params.clock_speed = 0;
1625
1626                 /* if network interface up, reprogram hardware */
1627                 if (info->netcount)
1628                         program_hw(info);
1629                 return 0;
1630
1631         default:
1632                 return hdlc_ioctl(dev, ifr, cmd);
1633         }
1634 }
1635
1636 /**
1637  * called by network layer when transmit timeout is detected
1638  *
1639  * dev  pointer to network device structure
1640  */
1641 static void hdlcdev_tx_timeout(struct net_device *dev)
1642 {
1643         struct slgt_info *info = dev_to_port(dev);
1644         struct net_device_stats *stats = hdlc_stats(dev);
1645         unsigned long flags;
1646
1647         DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1648
1649         stats->tx_errors++;
1650         stats->tx_aborted_errors++;
1651
1652         spin_lock_irqsave(&info->lock,flags);
1653         tx_stop(info);
1654         spin_unlock_irqrestore(&info->lock,flags);
1655
1656         netif_wake_queue(dev);
1657 }
1658
1659 /**
1660  * called by device driver when transmit completes
1661  * reenable network layer transmit if stopped
1662  *
1663  * info  pointer to device instance information
1664  */
1665 static void hdlcdev_tx_done(struct slgt_info *info)
1666 {
1667         if (netif_queue_stopped(info->netdev))
1668                 netif_wake_queue(info->netdev);
1669 }
1670
1671 /**
1672  * called by device driver when frame received
1673  * pass frame to network layer
1674  *
1675  * info  pointer to device instance information
1676  * buf   pointer to buffer contianing frame data
1677  * size  count of data bytes in buf
1678  */
1679 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1680 {
1681         struct sk_buff *skb = dev_alloc_skb(size);
1682         struct net_device *dev = info->netdev;
1683         struct net_device_stats *stats = hdlc_stats(dev);
1684
1685         DBGINFO(("%s hdlcdev_rx\n", dev->name));
1686
1687         if (skb == NULL) {
1688                 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1689                 stats->rx_dropped++;
1690                 return;
1691         }
1692
1693         memcpy(skb_put(skb, size),buf,size);
1694
1695         skb->protocol = hdlc_type_trans(skb, info->netdev);
1696
1697         stats->rx_packets++;
1698         stats->rx_bytes += size;
1699
1700         netif_rx(skb);
1701
1702         info->netdev->last_rx = jiffies;
1703 }
1704
1705 /**
1706  * called by device driver when adding device instance
1707  * do generic HDLC initialization
1708  *
1709  * info  pointer to device instance information
1710  *
1711  * returns 0 if success, otherwise error code
1712  */
1713 static int hdlcdev_init(struct slgt_info *info)
1714 {
1715         int rc;
1716         struct net_device *dev;
1717         hdlc_device *hdlc;
1718
1719         /* allocate and initialize network and HDLC layer objects */
1720
1721         if (!(dev = alloc_hdlcdev(info))) {
1722                 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1723                 return -ENOMEM;
1724         }
1725
1726         /* for network layer reporting purposes only */
1727         dev->mem_start = info->phys_reg_addr;
1728         dev->mem_end   = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1729         dev->irq       = info->irq_level;
1730
1731         /* network layer callbacks and settings */
1732         dev->do_ioctl       = hdlcdev_ioctl;
1733         dev->open           = hdlcdev_open;
1734         dev->stop           = hdlcdev_close;
1735         dev->tx_timeout     = hdlcdev_tx_timeout;
1736         dev->watchdog_timeo = 10*HZ;
1737         dev->tx_queue_len   = 50;
1738
1739         /* generic HDLC layer callbacks and settings */
1740         hdlc         = dev_to_hdlc(dev);
1741         hdlc->attach = hdlcdev_attach;
1742         hdlc->xmit   = hdlcdev_xmit;
1743
1744         /* register objects with HDLC layer */
1745         if ((rc = register_hdlc_device(dev))) {
1746                 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1747                 free_netdev(dev);
1748                 return rc;
1749         }
1750
1751         info->netdev = dev;
1752         return 0;
1753 }
1754
1755 /**
1756  * called by device driver when removing device instance
1757  * do generic HDLC cleanup
1758  *
1759  * info  pointer to device instance information
1760  */
1761 static void hdlcdev_exit(struct slgt_info *info)
1762 {
1763         unregister_hdlc_device(info->netdev);
1764         free_netdev(info->netdev);
1765         info->netdev = NULL;
1766 }
1767
1768 #endif /* ifdef CONFIG_HDLC */
1769
1770 /*
1771  * get async data from rx DMA buffers
1772  */
1773 static void rx_async(struct slgt_info *info)
1774 {
1775         struct tty_struct *tty = info->tty;
1776         struct mgsl_icount *icount = &info->icount;
1777         unsigned int start, end;
1778         unsigned char *p;
1779         unsigned char status;
1780         struct slgt_desc *bufs = info->rbufs;
1781         int i, count;
1782         int chars = 0;
1783         int stat;
1784         unsigned char ch;
1785
1786         start = end = info->rbuf_current;
1787
1788         while(desc_complete(bufs[end])) {
1789                 count = desc_count(bufs[end]) - info->rbuf_index;
1790                 p     = bufs[end].buf + info->rbuf_index;
1791
1792                 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1793                 DBGDATA(info, p, count, "rx");
1794
1795                 for(i=0 ; i < count; i+=2, p+=2) {
1796                         ch = *p;
1797                         icount->rx++;
1798
1799                         stat = 0;
1800
1801                         if ((status = *(p+1) & (BIT9 + BIT8))) {
1802                                 if (status & BIT9)
1803                                         icount->parity++;
1804                                 else if (status & BIT8)
1805                                         icount->frame++;
1806                                 /* discard char if tty control flags say so */
1807                                 if (status & info->ignore_status_mask)
1808                                         continue;
1809                                 if (status & BIT9)
1810                                         stat = TTY_PARITY;
1811                                 else if (status & BIT8)
1812                                         stat = TTY_FRAME;
1813                         }
1814                         if (tty) {
1815                                 tty_insert_flip_char(tty, ch, stat);
1816                                 chars++;
1817                         }
1818                 }
1819
1820                 if (i < count) {
1821                         /* receive buffer not completed */
1822                         info->rbuf_index += i;
1823                         info->rx_timer.expires = jiffies + 1;
1824                         add_timer(&info->rx_timer);
1825                         break;
1826                 }
1827
1828                 info->rbuf_index = 0;
1829                 free_rbufs(info, end, end);
1830
1831                 if (++end == info->rbuf_count)
1832                         end = 0;
1833
1834                 /* if entire list searched then no frame available */
1835                 if (end == start)
1836                         break;
1837         }
1838
1839         if (tty && chars)
1840                 tty_flip_buffer_push(tty);
1841 }
1842
1843 /*
1844  * return next bottom half action to perform
1845  */
1846 static int bh_action(struct slgt_info *info)
1847 {
1848         unsigned long flags;
1849         int rc;
1850
1851         spin_lock_irqsave(&info->lock,flags);
1852
1853         if (info->pending_bh & BH_RECEIVE) {
1854                 info->pending_bh &= ~BH_RECEIVE;
1855                 rc = BH_RECEIVE;
1856         } else if (info->pending_bh & BH_TRANSMIT) {
1857                 info->pending_bh &= ~BH_TRANSMIT;
1858                 rc = BH_TRANSMIT;
1859         } else if (info->pending_bh & BH_STATUS) {
1860                 info->pending_bh &= ~BH_STATUS;
1861                 rc = BH_STATUS;
1862         } else {
1863                 /* Mark BH routine as complete */
1864                 info->bh_running   = 0;
1865                 info->bh_requested = 0;
1866                 rc = 0;
1867         }
1868
1869         spin_unlock_irqrestore(&info->lock,flags);
1870
1871         return rc;
1872 }
1873
1874 /*
1875  * perform bottom half processing
1876  */
1877 static void bh_handler(void* context)
1878 {
1879         struct slgt_info *info = context;
1880         int action;
1881
1882         if (!info)
1883                 return;
1884         info->bh_running = 1;
1885
1886         while((action = bh_action(info))) {
1887                 switch (action) {
1888                 case BH_RECEIVE:
1889                         DBGBH(("%s bh receive\n", info->device_name));
1890                         switch(info->params.mode) {
1891                         case MGSL_MODE_ASYNC:
1892                                 rx_async(info);
1893                                 break;
1894                         case MGSL_MODE_HDLC:
1895                                 while(rx_get_frame(info));
1896                                 break;
1897                         case MGSL_MODE_RAW:
1898                                 while(rx_get_buf(info));
1899                                 break;
1900                         }
1901                         /* restart receiver if rx DMA buffers exhausted */
1902                         if (info->rx_restart)
1903                                 rx_start(info);
1904                         break;
1905                 case BH_TRANSMIT:
1906                         bh_transmit(info);
1907                         break;
1908                 case BH_STATUS:
1909                         DBGBH(("%s bh status\n", info->device_name));
1910                         info->ri_chkcount = 0;
1911                         info->dsr_chkcount = 0;
1912                         info->dcd_chkcount = 0;
1913                         info->cts_chkcount = 0;
1914                         break;
1915                 default:
1916                         DBGBH(("%s unknown action\n", info->device_name));
1917                         break;
1918                 }
1919         }
1920         DBGBH(("%s bh_handler exit\n", info->device_name));
1921 }
1922
1923 static void bh_transmit(struct slgt_info *info)
1924 {
1925         struct tty_struct *tty = info->tty;
1926
1927         DBGBH(("%s bh_transmit\n", info->device_name));
1928         if (tty) {
1929                 tty_wakeup(tty);
1930                 wake_up_interruptible(&tty->write_wait);
1931         }
1932 }
1933
1934 static void dsr_change(struct slgt_info *info)
1935 {
1936         get_signals(info);
1937         DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
1938         if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1939                 slgt_irq_off(info, IRQ_DSR);
1940                 return;
1941         }
1942         info->icount.dsr++;
1943         if (info->signals & SerialSignal_DSR)
1944                 info->input_signal_events.dsr_up++;
1945         else
1946                 info->input_signal_events.dsr_down++;
1947         wake_up_interruptible(&info->status_event_wait_q);
1948         wake_up_interruptible(&info->event_wait_q);
1949         info->pending_bh |= BH_STATUS;
1950 }
1951
1952 static void cts_change(struct slgt_info *info)
1953 {
1954         get_signals(info);
1955         DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
1956         if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1957                 slgt_irq_off(info, IRQ_CTS);
1958                 return;
1959         }
1960         info->icount.cts++;
1961         if (info->signals & SerialSignal_CTS)
1962                 info->input_signal_events.cts_up++;
1963         else
1964                 info->input_signal_events.cts_down++;
1965         wake_up_interruptible(&info->status_event_wait_q);
1966         wake_up_interruptible(&info->event_wait_q);
1967         info->pending_bh |= BH_STATUS;
1968
1969         if (info->flags & ASYNC_CTS_FLOW) {
1970                 if (info->tty) {
1971                         if (info->tty->hw_stopped) {
1972                                 if (info->signals & SerialSignal_CTS) {
1973                                         info->tty->hw_stopped = 0;
1974                                         info->pending_bh |= BH_TRANSMIT;
1975                                         return;
1976                                 }
1977                         } else {
1978                                 if (!(info->signals & SerialSignal_CTS))
1979                                         info->tty->hw_stopped = 1;
1980                         }
1981                 }
1982         }
1983 }
1984
1985 static void dcd_change(struct slgt_info *info)
1986 {
1987         get_signals(info);
1988         DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
1989         if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1990                 slgt_irq_off(info, IRQ_DCD);
1991                 return;
1992         }
1993         info->icount.dcd++;
1994         if (info->signals & SerialSignal_DCD) {
1995                 info->input_signal_events.dcd_up++;
1996         } else {
1997                 info->input_signal_events.dcd_down++;
1998         }
1999 #ifdef CONFIG_HDLC
2000         if (info->netcount)
2001                 hdlc_set_carrier(info->signals & SerialSignal_DCD, info->netdev);
2002 #endif
2003         wake_up_interruptible(&info->status_event_wait_q);
2004         wake_up_interruptible(&info->event_wait_q);
2005         info->pending_bh |= BH_STATUS;
2006
2007         if (info->flags & ASYNC_CHECK_CD) {
2008                 if (info->signals & SerialSignal_DCD)
2009                         wake_up_interruptible(&info->open_wait);
2010                 else {
2011                         if (info->tty)
2012                                 tty_hangup(info->tty);
2013                 }
2014         }
2015 }
2016
2017 static void ri_change(struct slgt_info *info)
2018 {
2019         get_signals(info);
2020         DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2021         if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2022                 slgt_irq_off(info, IRQ_RI);
2023                 return;
2024         }
2025         info->icount.dcd++;
2026         if (info->signals & SerialSignal_RI) {
2027                 info->input_signal_events.ri_up++;
2028         } else {
2029                 info->input_signal_events.ri_down++;
2030         }
2031         wake_up_interruptible(&info->status_event_wait_q);
2032         wake_up_interruptible(&info->event_wait_q);
2033         info->pending_bh |= BH_STATUS;
2034 }
2035
2036 static void isr_serial(struct slgt_info *info)
2037 {
2038         unsigned short status = rd_reg16(info, SSR);
2039
2040         DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2041
2042         wr_reg16(info, SSR, status); /* clear pending */
2043
2044         info->irq_occurred = 1;
2045
2046         if (info->params.mode == MGSL_MODE_ASYNC) {
2047                 if (status & IRQ_TXIDLE) {
2048                         if (info->tx_count)
2049                                 isr_txeom(info, status);
2050                 }
2051                 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2052                         info->icount.brk++;
2053                         /* process break detection if tty control allows */
2054                         if (info->tty) {
2055                                 if (!(status & info->ignore_status_mask)) {
2056                                         if (info->read_status_mask & MASK_BREAK) {
2057                                                 tty_insert_flip_char(info->tty, 0, TTY_BREAK);
2058                                                 if (info->flags & ASYNC_SAK)
2059                                                         do_SAK(info->tty);
2060                                         }
2061                                 }
2062                         }
2063                 }
2064         } else {
2065                 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2066                         isr_txeom(info, status);
2067
2068                 if (status & IRQ_RXIDLE) {
2069                         if (status & RXIDLE)
2070                                 info->icount.rxidle++;
2071                         else
2072                                 info->icount.exithunt++;
2073                         wake_up_interruptible(&info->event_wait_q);
2074                 }
2075
2076                 if (status & IRQ_RXOVER)
2077                         rx_start(info);
2078         }
2079
2080         if (status & IRQ_DSR)
2081                 dsr_change(info);
2082         if (status & IRQ_CTS)
2083                 cts_change(info);
2084         if (status & IRQ_DCD)
2085                 dcd_change(info);
2086         if (status & IRQ_RI)
2087                 ri_change(info);
2088 }
2089
2090 static void isr_rdma(struct slgt_info *info)
2091 {
2092         unsigned int status = rd_reg32(info, RDCSR);
2093
2094         DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2095
2096         /* RDCSR (rx DMA control/status)
2097          *
2098          * 31..07  reserved
2099          * 06      save status byte to DMA buffer
2100          * 05      error
2101          * 04      eol (end of list)
2102          * 03      eob (end of buffer)
2103          * 02      IRQ enable
2104          * 01      reset
2105          * 00      enable
2106          */
2107         wr_reg32(info, RDCSR, status);  /* clear pending */
2108
2109         if (status & (BIT5 + BIT4)) {
2110                 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2111                 info->rx_restart = 1;
2112         }
2113         info->pending_bh |= BH_RECEIVE;
2114 }
2115
2116 static void isr_tdma(struct slgt_info *info)
2117 {
2118         unsigned int status = rd_reg32(info, TDCSR);
2119
2120         DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2121
2122         /* TDCSR (tx DMA control/status)
2123          *
2124          * 31..06  reserved
2125          * 05      error
2126          * 04      eol (end of list)
2127          * 03      eob (end of buffer)
2128          * 02      IRQ enable
2129          * 01      reset
2130          * 00      enable
2131          */
2132         wr_reg32(info, TDCSR, status);  /* clear pending */
2133
2134         if (status & (BIT5 + BIT4 + BIT3)) {
2135                 // another transmit buffer has completed
2136                 // run bottom half to get more send data from user
2137                 info->pending_bh |= BH_TRANSMIT;
2138         }
2139 }
2140
2141 static void isr_txeom(struct slgt_info *info, unsigned short status)
2142 {
2143         DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2144
2145         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2146         tdma_reset(info);
2147         reset_tbufs(info);
2148         if (status & IRQ_TXUNDER) {
2149                 unsigned short val = rd_reg16(info, TCR);
2150                 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2151                 wr_reg16(info, TCR, val); /* clear reset bit */
2152         }
2153
2154         if (info->tx_active) {
2155                 if (info->params.mode != MGSL_MODE_ASYNC) {
2156                         if (status & IRQ_TXUNDER)
2157                                 info->icount.txunder++;
2158                         else if (status & IRQ_TXIDLE)
2159                                 info->icount.txok++;
2160                 }
2161
2162                 info->tx_active = 0;
2163                 info->tx_count = 0;
2164
2165                 del_timer(&info->tx_timer);
2166
2167                 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2168                         info->signals &= ~SerialSignal_RTS;
2169                         info->drop_rts_on_tx_done = 0;
2170                         set_signals(info);
2171                 }
2172
2173 #ifdef CONFIG_HDLC
2174                 if (info->netcount)
2175                         hdlcdev_tx_done(info);
2176                 else
2177 #endif
2178                 {
2179                         if (info->tty && (info->tty->stopped || info->tty->hw_stopped)) {
2180                                 tx_stop(info);
2181                                 return;
2182                         }
2183                         info->pending_bh |= BH_TRANSMIT;
2184                 }
2185         }
2186 }
2187
2188 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2189 {
2190         struct cond_wait *w, *prev;
2191
2192         /* wake processes waiting for specific transitions */
2193         for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2194                 if (w->data & changed) {
2195                         w->data = state;
2196                         wake_up_interruptible(&w->q);
2197                         if (prev != NULL)
2198                                 prev->next = w->next;
2199                         else
2200                                 info->gpio_wait_q = w->next;
2201                 } else
2202                         prev = w;
2203         }
2204 }
2205
2206 /* interrupt service routine
2207  *
2208  *      irq     interrupt number
2209  *      dev_id  device ID supplied during interrupt registration
2210  *      regs    interrupted processor context
2211  */
2212 static irqreturn_t slgt_interrupt(int irq, void *dev_id, struct pt_regs * regs)
2213 {
2214         struct slgt_info *info;
2215         unsigned int gsr;
2216         unsigned int i;
2217
2218         DBGISR(("slgt_interrupt irq=%d entry\n", irq));
2219
2220         info = dev_id;
2221         if (!info)
2222                 return IRQ_NONE;
2223
2224         spin_lock(&info->lock);
2225
2226         while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2227                 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2228                 info->irq_occurred = 1;
2229                 for(i=0; i < info->port_count ; i++) {
2230                         if (info->port_array[i] == NULL)
2231                                 continue;
2232                         if (gsr & (BIT8 << i))
2233                                 isr_serial(info->port_array[i]);
2234                         if (gsr & (BIT16 << (i*2)))
2235                                 isr_rdma(info->port_array[i]);
2236                         if (gsr & (BIT17 << (i*2)))
2237                                 isr_tdma(info->port_array[i]);
2238                 }
2239         }
2240
2241         if (info->gpio_present) {
2242                 unsigned int state;
2243                 unsigned int changed;
2244                 while ((changed = rd_reg32(info, IOSR)) != 0) {
2245                         DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2246                         /* read latched state of GPIO signals */
2247                         state = rd_reg32(info, IOVR);
2248                         /* clear pending GPIO interrupt bits */
2249                         wr_reg32(info, IOSR, changed);
2250                         for (i=0 ; i < info->port_count ; i++) {
2251                                 if (info->port_array[i] != NULL)
2252                                         isr_gpio(info->port_array[i], changed, state);
2253                         }
2254                 }
2255         }
2256
2257         for(i=0; i < info->port_count ; i++) {
2258                 struct slgt_info *port = info->port_array[i];
2259
2260                 if (port && (port->count || port->netcount) &&
2261                     port->pending_bh && !port->bh_running &&
2262                     !port->bh_requested) {
2263                         DBGISR(("%s bh queued\n", port->device_name));
2264                         schedule_work(&port->task);
2265                         port->bh_requested = 1;
2266                 }
2267         }
2268
2269         spin_unlock(&info->lock);
2270
2271         DBGISR(("slgt_interrupt irq=%d exit\n", irq));
2272         return IRQ_HANDLED;
2273 }
2274
2275 static int startup(struct slgt_info *info)
2276 {
2277         DBGINFO(("%s startup\n", info->device_name));
2278
2279         if (info->flags & ASYNC_INITIALIZED)
2280                 return 0;
2281
2282         if (!info->tx_buf) {
2283                 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2284                 if (!info->tx_buf) {
2285                         DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2286                         return -ENOMEM;
2287                 }
2288         }
2289
2290         info->pending_bh = 0;
2291
2292         memset(&info->icount, 0, sizeof(info->icount));
2293
2294         /* program hardware for current parameters */
2295         change_params(info);
2296
2297         if (info->tty)
2298                 clear_bit(TTY_IO_ERROR, &info->tty->flags);
2299
2300         info->flags |= ASYNC_INITIALIZED;
2301
2302         return 0;
2303 }
2304
2305 /*
2306  *  called by close() and hangup() to shutdown hardware
2307  */
2308 static void shutdown(struct slgt_info *info)
2309 {
2310         unsigned long flags;
2311
2312         if (!(info->flags & ASYNC_INITIALIZED))
2313                 return;
2314
2315         DBGINFO(("%s shutdown\n", info->device_name));
2316
2317         /* clear status wait queue because status changes */
2318         /* can't happen after shutting down the hardware */
2319         wake_up_interruptible(&info->status_event_wait_q);
2320         wake_up_interruptible(&info->event_wait_q);
2321
2322         del_timer_sync(&info->tx_timer);
2323         del_timer_sync(&info->rx_timer);
2324
2325         kfree(info->tx_buf);
2326         info->tx_buf = NULL;
2327
2328         spin_lock_irqsave(&info->lock,flags);
2329
2330         tx_stop(info);
2331         rx_stop(info);
2332
2333         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2334
2335         if (!info->tty || info->tty->termios->c_cflag & HUPCL) {
2336                 info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
2337                 set_signals(info);
2338         }
2339
2340         flush_cond_wait(&info->gpio_wait_q);
2341
2342         spin_unlock_irqrestore(&info->lock,flags);
2343
2344         if (info->tty)
2345                 set_bit(TTY_IO_ERROR, &info->tty->flags);
2346
2347         info->flags &= ~ASYNC_INITIALIZED;
2348 }
2349
2350 static void program_hw(struct slgt_info *info)
2351 {
2352         unsigned long flags;
2353
2354         spin_lock_irqsave(&info->lock,flags);
2355
2356         rx_stop(info);
2357         tx_stop(info);
2358
2359         if (info->params.mode == MGSL_MODE_HDLC ||
2360             info->params.mode == MGSL_MODE_RAW ||
2361             info->netcount)
2362                 hdlc_mode(info);
2363         else
2364                 async_mode(info);
2365
2366         set_signals(info);
2367
2368         info->dcd_chkcount = 0;
2369         info->cts_chkcount = 0;
2370         info->ri_chkcount = 0;
2371         info->dsr_chkcount = 0;
2372
2373         slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR);
2374         get_signals(info);
2375
2376         if (info->netcount ||
2377             (info->tty && info->tty->termios->c_cflag & CREAD))
2378                 rx_start(info);
2379
2380         spin_unlock_irqrestore(&info->lock,flags);
2381 }
2382
2383 /*
2384  * reconfigure adapter based on new parameters
2385  */
2386 static void change_params(struct slgt_info *info)
2387 {
2388         unsigned cflag;
2389         int bits_per_char;
2390
2391         if (!info->tty || !info->tty->termios)
2392                 return;
2393         DBGINFO(("%s change_params\n", info->device_name));
2394
2395         cflag = info->tty->termios->c_cflag;
2396
2397         /* if B0 rate (hangup) specified then negate DTR and RTS */
2398         /* otherwise assert DTR and RTS */
2399         if (cflag & CBAUD)
2400                 info->signals |= SerialSignal_RTS + SerialSignal_DTR;
2401         else
2402                 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
2403
2404         /* byte size and parity */
2405
2406         switch (cflag & CSIZE) {
2407         case CS5: info->params.data_bits = 5; break;
2408         case CS6: info->params.data_bits = 6; break;
2409         case CS7: info->params.data_bits = 7; break;
2410         case CS8: info->params.data_bits = 8; break;
2411         default:  info->params.data_bits = 7; break;
2412         }
2413
2414         info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2415
2416         if (cflag & PARENB)
2417                 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2418         else
2419                 info->params.parity = ASYNC_PARITY_NONE;
2420
2421         /* calculate number of jiffies to transmit a full
2422          * FIFO (32 bytes) at specified data rate
2423          */
2424         bits_per_char = info->params.data_bits +
2425                         info->params.stop_bits + 1;
2426
2427         info->params.data_rate = tty_get_baud_rate(info->tty);
2428
2429         if (info->params.data_rate) {
2430                 info->timeout = (32*HZ*bits_per_char) /
2431                                 info->params.data_rate;
2432         }
2433         info->timeout += HZ/50;         /* Add .02 seconds of slop */
2434
2435         if (cflag & CRTSCTS)
2436                 info->flags |= ASYNC_CTS_FLOW;
2437         else
2438                 info->flags &= ~ASYNC_CTS_FLOW;
2439
2440         if (cflag & CLOCAL)
2441                 info->flags &= ~ASYNC_CHECK_CD;
2442         else
2443                 info->flags |= ASYNC_CHECK_CD;
2444
2445         /* process tty input control flags */
2446
2447         info->read_status_mask = IRQ_RXOVER;
2448         if (I_INPCK(info->tty))
2449                 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2450         if (I_BRKINT(info->tty) || I_PARMRK(info->tty))
2451                 info->read_status_mask |= MASK_BREAK;
2452         if (I_IGNPAR(info->tty))
2453                 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2454         if (I_IGNBRK(info->tty)) {
2455                 info->ignore_status_mask |= MASK_BREAK;
2456                 /* If ignoring parity and break indicators, ignore
2457                  * overruns too.  (For real raw support).
2458                  */
2459                 if (I_IGNPAR(info->tty))
2460                         info->ignore_status_mask |= MASK_OVERRUN;
2461         }
2462
2463         program_hw(info);
2464 }
2465
2466 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2467 {
2468         DBGINFO(("%s get_stats\n",  info->device_name));
2469         if (!user_icount) {
2470                 memset(&info->icount, 0, sizeof(info->icount));
2471         } else {
2472                 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2473                         return -EFAULT;
2474         }
2475         return 0;
2476 }
2477
2478 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2479 {
2480         DBGINFO(("%s get_params\n", info->device_name));
2481         if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2482                 return -EFAULT;
2483         return 0;
2484 }
2485
2486 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2487 {
2488         unsigned long flags;
2489         MGSL_PARAMS tmp_params;
2490
2491         DBGINFO(("%s set_params\n", info->device_name));
2492         if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2493                 return -EFAULT;
2494
2495         spin_lock_irqsave(&info->lock, flags);
2496         memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2497         spin_unlock_irqrestore(&info->lock, flags);
2498
2499         change_params(info);
2500
2501         return 0;
2502 }
2503
2504 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2505 {
2506         DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2507         if (put_user(info->idle_mode, idle_mode))
2508                 return -EFAULT;
2509         return 0;
2510 }
2511
2512 static int set_txidle(struct slgt_info *info, int idle_mode)
2513 {
2514         unsigned long flags;
2515         DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2516         spin_lock_irqsave(&info->lock,flags);
2517         info->idle_mode = idle_mode;
2518         tx_set_idle(info);
2519         spin_unlock_irqrestore(&info->lock,flags);
2520         return 0;
2521 }
2522
2523 static int tx_enable(struct slgt_info *info, int enable)
2524 {
2525         unsigned long flags;
2526         DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2527         spin_lock_irqsave(&info->lock,flags);
2528         if (enable) {
2529                 if (!info->tx_enabled)
2530                         tx_start(info);
2531         } else {
2532                 if (info->tx_enabled)
2533                         tx_stop(info);
2534         }
2535         spin_unlock_irqrestore(&info->lock,flags);
2536         return 0;
2537 }
2538
2539 /*
2540  * abort transmit HDLC frame
2541  */
2542 static int tx_abort(struct slgt_info *info)
2543 {
2544         unsigned long flags;
2545         DBGINFO(("%s tx_abort\n", info->device_name));
2546         spin_lock_irqsave(&info->lock,flags);
2547         tdma_reset(info);
2548         spin_unlock_irqrestore(&info->lock,flags);
2549         return 0;
2550 }
2551
2552 static int rx_enable(struct slgt_info *info, int enable)
2553 {
2554         unsigned long flags;
2555         DBGINFO(("%s rx_enable(%d)\n", info->device_name, enable));
2556         spin_lock_irqsave(&info->lock,flags);
2557         if (enable) {
2558                 if (!info->rx_enabled)
2559                         rx_start(info);
2560         } else {
2561                 if (info->rx_enabled)
2562                         rx_stop(info);
2563         }
2564         spin_unlock_irqrestore(&info->lock,flags);
2565         return 0;
2566 }
2567
2568 /*
2569  *  wait for specified event to occur
2570  */
2571 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2572 {
2573         unsigned long flags;
2574         int s;
2575         int rc=0;
2576         struct mgsl_icount cprev, cnow;
2577         int events;
2578         int mask;
2579         struct  _input_signal_events oldsigs, newsigs;
2580         DECLARE_WAITQUEUE(wait, current);
2581
2582         if (get_user(mask, mask_ptr))
2583                 return -EFAULT;
2584
2585         DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2586
2587         spin_lock_irqsave(&info->lock,flags);
2588
2589         /* return immediately if state matches requested events */
2590         get_signals(info);
2591         s = info->signals;
2592
2593         events = mask &
2594                 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2595                   ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2596                   ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2597                   ((s & SerialSignal_RI)  ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2598         if (events) {
2599                 spin_unlock_irqrestore(&info->lock,flags);
2600                 goto exit;
2601         }
2602
2603         /* save current irq counts */
2604         cprev = info->icount;
2605         oldsigs = info->input_signal_events;
2606
2607         /* enable hunt and idle irqs if needed */
2608         if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2609                 unsigned short val = rd_reg16(info, SCR);
2610                 if (!(val & IRQ_RXIDLE))
2611                         wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2612         }
2613
2614         set_current_state(TASK_INTERRUPTIBLE);
2615         add_wait_queue(&info->event_wait_q, &wait);
2616
2617         spin_unlock_irqrestore(&info->lock,flags);
2618
2619         for(;;) {
2620                 schedule();
2621                 if (signal_pending(current)) {
2622                         rc = -ERESTARTSYS;
2623                         break;
2624                 }
2625
2626                 /* get current irq counts */
2627                 spin_lock_irqsave(&info->lock,flags);
2628                 cnow = info->icount;
2629                 newsigs = info->input_signal_events;
2630                 set_current_state(TASK_INTERRUPTIBLE);
2631                 spin_unlock_irqrestore(&info->lock,flags);
2632
2633                 /* if no change, wait aborted for some reason */
2634                 if (newsigs.dsr_up   == oldsigs.dsr_up   &&
2635                     newsigs.dsr_down == oldsigs.dsr_down &&
2636                     newsigs.dcd_up   == oldsigs.dcd_up   &&
2637                     newsigs.dcd_down == oldsigs.dcd_down &&
2638                     newsigs.cts_up   == oldsigs.cts_up   &&
2639                     newsigs.cts_down == oldsigs.cts_down &&
2640                     newsigs.ri_up    == oldsigs.ri_up    &&
2641                     newsigs.ri_down  == oldsigs.ri_down  &&
2642                     cnow.exithunt    == cprev.exithunt   &&
2643                     cnow.rxidle      == cprev.rxidle) {
2644                         rc = -EIO;
2645                         break;
2646                 }
2647
2648                 events = mask &
2649                         ( (newsigs.dsr_up   != oldsigs.dsr_up   ? MgslEvent_DsrActive:0)   +
2650                           (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2651                           (newsigs.dcd_up   != oldsigs.dcd_up   ? MgslEvent_DcdActive:0)   +
2652                           (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2653                           (newsigs.cts_up   != oldsigs.cts_up   ? MgslEvent_CtsActive:0)   +
2654                           (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2655                           (newsigs.ri_up    != oldsigs.ri_up    ? MgslEvent_RiActive:0)    +
2656                           (newsigs.ri_down  != oldsigs.ri_down  ? MgslEvent_RiInactive:0)  +
2657                           (cnow.exithunt    != cprev.exithunt   ? MgslEvent_ExitHuntMode:0) +
2658                           (cnow.rxidle      != cprev.rxidle     ? MgslEvent_IdleReceived:0) );
2659                 if (events)
2660                         break;
2661
2662                 cprev = cnow;
2663                 oldsigs = newsigs;
2664         }
2665
2666         remove_wait_queue(&info->event_wait_q, &wait);
2667         set_current_state(TASK_RUNNING);
2668
2669
2670         if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2671                 spin_lock_irqsave(&info->lock,flags);
2672                 if (!waitqueue_active(&info->event_wait_q)) {
2673                         /* disable enable exit hunt mode/idle rcvd IRQs */
2674                         wr_reg16(info, SCR,
2675                                 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2676                 }
2677                 spin_unlock_irqrestore(&info->lock,flags);
2678         }
2679 exit:
2680         if (rc == 0)
2681                 rc = put_user(events, mask_ptr);
2682         return rc;
2683 }
2684
2685 static int get_interface(struct slgt_info *info, int __user *if_mode)
2686 {
2687         DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2688         if (put_user(info->if_mode, if_mode))
2689                 return -EFAULT;
2690         return 0;
2691 }
2692
2693 static int set_interface(struct slgt_info *info, int if_mode)
2694 {
2695         unsigned long flags;
2696         unsigned short val;
2697
2698         DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2699         spin_lock_irqsave(&info->lock,flags);
2700         info->if_mode = if_mode;
2701
2702         msc_set_vcr(info);
2703
2704         /* TCR (tx control) 07  1=RTS driver control */
2705         val = rd_reg16(info, TCR);
2706         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2707                 val |= BIT7;
2708         else
2709                 val &= ~BIT7;
2710         wr_reg16(info, TCR, val);
2711
2712         spin_unlock_irqrestore(&info->lock,flags);
2713         return 0;
2714 }
2715
2716 /*
2717  * set general purpose IO pin state and direction
2718  *
2719  * user_gpio fields:
2720  * state   each bit indicates a pin state
2721  * smask   set bit indicates pin state to set
2722  * dir     each bit indicates a pin direction (0=input, 1=output)
2723  * dmask   set bit indicates pin direction to set
2724  */
2725 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2726 {
2727         unsigned long flags;
2728         struct gpio_desc gpio;
2729         __u32 data;
2730
2731         if (!info->gpio_present)
2732                 return -EINVAL;
2733         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2734                 return -EFAULT;
2735         DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2736                  info->device_name, gpio.state, gpio.smask,
2737                  gpio.dir, gpio.dmask));
2738
2739         spin_lock_irqsave(&info->lock,flags);
2740         if (gpio.dmask) {
2741                 data = rd_reg32(info, IODR);
2742                 data |= gpio.dmask & gpio.dir;
2743                 data &= ~(gpio.dmask & ~gpio.dir);
2744                 wr_reg32(info, IODR, data);
2745         }
2746         if (gpio.smask) {
2747                 data = rd_reg32(info, IOVR);
2748                 data |= gpio.smask & gpio.state;
2749                 data &= ~(gpio.smask & ~gpio.state);
2750                 wr_reg32(info, IOVR, data);
2751         }
2752         spin_unlock_irqrestore(&info->lock,flags);
2753
2754         return 0;
2755 }
2756
2757 /*
2758  * get general purpose IO pin state and direction
2759  */
2760 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2761 {
2762         struct gpio_desc gpio;
2763         if (!info->gpio_present)
2764                 return -EINVAL;
2765         gpio.state = rd_reg32(info, IOVR);
2766         gpio.smask = 0xffffffff;
2767         gpio.dir   = rd_reg32(info, IODR);
2768         gpio.dmask = 0xffffffff;
2769         if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2770                 return -EFAULT;
2771         DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
2772                  info->device_name, gpio.state, gpio.dir));
2773         return 0;
2774 }
2775
2776 /*
2777  * conditional wait facility
2778  */
2779 static void init_cond_wait(struct cond_wait *w, unsigned int data)
2780 {
2781         init_waitqueue_head(&w->q);
2782         init_waitqueue_entry(&w->wait, current);
2783         w->data = data;
2784 }
2785
2786 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
2787 {
2788         set_current_state(TASK_INTERRUPTIBLE);
2789         add_wait_queue(&w->q, &w->wait);
2790         w->next = *head;
2791         *head = w;
2792 }
2793
2794 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
2795 {
2796         struct cond_wait *w, *prev;
2797         remove_wait_queue(&cw->q, &cw->wait);
2798         set_current_state(TASK_RUNNING);
2799         for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
2800                 if (w == cw) {
2801                         if (prev != NULL)
2802                                 prev->next = w->next;
2803                         else
2804                                 *head = w->next;
2805                         break;
2806                 }
2807         }
2808 }
2809
2810 static void flush_cond_wait(struct cond_wait **head)
2811 {
2812         while (*head != NULL) {
2813                 wake_up_interruptible(&(*head)->q);
2814                 *head = (*head)->next;
2815         }
2816 }
2817
2818 /*
2819  * wait for general purpose I/O pin(s) to enter specified state
2820  *
2821  * user_gpio fields:
2822  * state - bit indicates target pin state
2823  * smask - set bit indicates watched pin
2824  *
2825  * The wait ends when at least one watched pin enters the specified
2826  * state. When 0 (no error) is returned, user_gpio->state is set to the
2827  * state of all GPIO pins when the wait ends.
2828  *
2829  * Note: Each pin may be a dedicated input, dedicated output, or
2830  * configurable input/output. The number and configuration of pins
2831  * varies with the specific adapter model. Only input pins (dedicated
2832  * or configured) can be monitored with this function.
2833  */
2834 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2835 {
2836         unsigned long flags;
2837         int rc = 0;
2838         struct gpio_desc gpio;
2839         struct cond_wait wait;
2840         u32 state;
2841
2842         if (!info->gpio_present)
2843                 return -EINVAL;
2844         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2845                 return -EFAULT;
2846         DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
2847                  info->device_name, gpio.state, gpio.smask));
2848         /* ignore output pins identified by set IODR bit */
2849         if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
2850                 return -EINVAL;
2851         init_cond_wait(&wait, gpio.smask);
2852
2853         spin_lock_irqsave(&info->lock, flags);
2854         /* enable interrupts for watched pins */
2855         wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
2856         /* get current pin states */
2857         state = rd_reg32(info, IOVR);
2858
2859         if (gpio.smask & ~(state ^ gpio.state)) {
2860                 /* already in target state */
2861                 gpio.state = state;
2862         } else {
2863                 /* wait for target state */
2864                 add_cond_wait(&info->gpio_wait_q, &wait);
2865                 spin_unlock_irqrestore(&info->lock, flags);
2866                 schedule();
2867                 if (signal_pending(current))
2868                         rc = -ERESTARTSYS;
2869                 else
2870                         gpio.state = wait.data;
2871                 spin_lock_irqsave(&info->lock, flags);
2872                 remove_cond_wait(&info->gpio_wait_q, &wait);
2873         }
2874
2875         /* disable all GPIO interrupts if no waiting processes */
2876         if (info->gpio_wait_q == NULL)
2877                 wr_reg32(info, IOER, 0);
2878         spin_unlock_irqrestore(&info->lock,flags);
2879
2880         if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2881                 rc = -EFAULT;
2882         return rc;
2883 }
2884
2885 static int modem_input_wait(struct slgt_info *info,int arg)
2886 {
2887         unsigned long flags;
2888         int rc;
2889         struct mgsl_icount cprev, cnow;
2890         DECLARE_WAITQUEUE(wait, current);
2891
2892         /* save current irq counts */
2893         spin_lock_irqsave(&info->lock,flags);
2894         cprev = info->icount;
2895         add_wait_queue(&info->status_event_wait_q, &wait);
2896         set_current_state(TASK_INTERRUPTIBLE);
2897         spin_unlock_irqrestore(&info->lock,flags);
2898
2899         for(;;) {
2900                 schedule();
2901                 if (signal_pending(current)) {
2902                         rc = -ERESTARTSYS;
2903                         break;
2904                 }
2905
2906                 /* get new irq counts */
2907                 spin_lock_irqsave(&info->lock,flags);
2908                 cnow = info->icount;
2909                 set_current_state(TASK_INTERRUPTIBLE);
2910                 spin_unlock_irqrestore(&info->lock,flags);
2911
2912                 /* if no change, wait aborted for some reason */
2913                 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
2914                     cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
2915                         rc = -EIO;
2916                         break;
2917                 }
2918
2919                 /* check for change in caller specified modem input */
2920                 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
2921                     (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
2922                     (arg & TIOCM_CD  && cnow.dcd != cprev.dcd) ||
2923                     (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
2924                         rc = 0;
2925                         break;
2926                 }
2927
2928                 cprev = cnow;
2929         }
2930         remove_wait_queue(&info->status_event_wait_q, &wait);
2931         set_current_state(TASK_RUNNING);
2932         return rc;
2933 }
2934
2935 /*
2936  *  return state of serial control and status signals
2937  */
2938 static int tiocmget(struct tty_struct *tty, struct file *file)
2939 {
2940         struct slgt_info *info = tty->driver_data;
2941         unsigned int result;
2942         unsigned long flags;
2943
2944         spin_lock_irqsave(&info->lock,flags);
2945         get_signals(info);
2946         spin_unlock_irqrestore(&info->lock,flags);
2947
2948         result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
2949                 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
2950                 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
2951                 ((info->signals & SerialSignal_RI)  ? TIOCM_RNG:0) +
2952                 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
2953                 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
2954
2955         DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
2956         return result;
2957 }
2958
2959 /*
2960  * set modem control signals (DTR/RTS)
2961  *
2962  *      cmd     signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
2963  *              TIOCMSET = set/clear signal values
2964  *      value   bit mask for command
2965  */
2966 static int tiocmset(struct tty_struct *tty, struct file *file,
2967                     unsigned int set, unsigned int clear)
2968 {
2969         struct slgt_info *info = tty->driver_data;
2970         unsigned long flags;
2971
2972         DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
2973
2974         if (set & TIOCM_RTS)
2975                 info->signals |= SerialSignal_RTS;
2976         if (set & TIOCM_DTR)
2977                 info->signals |= SerialSignal_DTR;
2978         if (clear & TIOCM_RTS)
2979                 info->signals &= ~SerialSignal_RTS;
2980         if (clear & TIOCM_DTR)
2981                 info->signals &= ~SerialSignal_DTR;
2982
2983         spin_lock_irqsave(&info->lock,flags);
2984         set_signals(info);
2985         spin_unlock_irqrestore(&info->lock,flags);
2986         return 0;
2987 }
2988
2989 /*
2990  *  block current process until the device is ready to open
2991  */
2992 static int block_til_ready(struct tty_struct *tty, struct file *filp,
2993                            struct slgt_info *info)
2994 {
2995         DECLARE_WAITQUEUE(wait, current);
2996         int             retval;
2997         int             do_clocal = 0, extra_count = 0;
2998         unsigned long   flags;
2999
3000         DBGINFO(("%s block_til_ready\n", tty->driver->name));
3001
3002         if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
3003                 /* nonblock mode is set or port is not enabled */
3004                 info->flags |= ASYNC_NORMAL_ACTIVE;
3005                 return 0;
3006         }
3007
3008         if (tty->termios->c_cflag & CLOCAL)
3009                 do_clocal = 1;
3010
3011         /* Wait for carrier detect and the line to become
3012          * free (i.e., not in use by the callout).  While we are in
3013          * this loop, info->count is dropped by one, so that
3014          * close() knows when to free things.  We restore it upon
3015          * exit, either normal or abnormal.
3016          */
3017
3018         retval = 0;
3019         add_wait_queue(&info->open_wait, &wait);
3020
3021         spin_lock_irqsave(&info->lock, flags);
3022         if (!tty_hung_up_p(filp)) {
3023                 extra_count = 1;
3024                 info->count--;
3025         }
3026         spin_unlock_irqrestore(&info->lock, flags);
3027         info->blocked_open++;
3028
3029         while (1) {
3030                 if ((tty->termios->c_cflag & CBAUD)) {
3031                         spin_lock_irqsave(&info->lock,flags);
3032                         info->signals |= SerialSignal_RTS + SerialSignal_DTR;
3033                         set_signals(info);
3034                         spin_unlock_irqrestore(&info->lock,flags);
3035                 }
3036
3037                 set_current_state(TASK_INTERRUPTIBLE);
3038
3039                 if (tty_hung_up_p(filp) || !(info->flags & ASYNC_INITIALIZED)){
3040                         retval = (info->flags & ASYNC_HUP_NOTIFY) ?
3041                                         -EAGAIN : -ERESTARTSYS;
3042                         break;
3043                 }
3044
3045                 spin_lock_irqsave(&info->lock,flags);
3046                 get_signals(info);
3047                 spin_unlock_irqrestore(&info->lock,flags);
3048
3049                 if (!(info->flags & ASYNC_CLOSING) &&
3050                     (do_clocal || (info->signals & SerialSignal_DCD)) ) {
3051                         break;
3052                 }
3053
3054                 if (signal_pending(current)) {
3055                         retval = -ERESTARTSYS;
3056                         break;
3057                 }
3058
3059                 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3060                 schedule();
3061         }
3062
3063         set_current_state(TASK_RUNNING);
3064         remove_wait_queue(&info->open_wait, &wait);
3065
3066         if (extra_count)
3067                 info->count++;
3068         info->blocked_open--;
3069
3070         if (!retval)
3071                 info->flags |= ASYNC_NORMAL_ACTIVE;
3072
3073         DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3074         return retval;
3075 }
3076
3077 static int alloc_tmp_rbuf(struct slgt_info *info)
3078 {
3079         info->tmp_rbuf = kmalloc(info->max_frame_size, GFP_KERNEL);
3080         if (info->tmp_rbuf == NULL)
3081                 return -ENOMEM;
3082         return 0;
3083 }
3084
3085 static void free_tmp_rbuf(struct slgt_info *info)
3086 {
3087         kfree(info->tmp_rbuf);
3088         info->tmp_rbuf = NULL;
3089 }
3090
3091 /*
3092  * allocate DMA descriptor lists.
3093  */
3094 static int alloc_desc(struct slgt_info *info)
3095 {
3096         unsigned int i;
3097         unsigned int pbufs;
3098
3099         /* allocate memory to hold descriptor lists */
3100         info->bufs = pci_alloc_consistent(info->pdev, DESC_LIST_SIZE, &info->bufs_dma_addr);
3101         if (info->bufs == NULL)
3102                 return -ENOMEM;
3103
3104         memset(info->bufs, 0, DESC_LIST_SIZE);
3105
3106         info->rbufs = (struct slgt_desc*)info->bufs;
3107         info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3108
3109         pbufs = (unsigned int)info->bufs_dma_addr;
3110
3111         /*
3112          * Build circular lists of descriptors
3113          */
3114
3115         for (i=0; i < info->rbuf_count; i++) {
3116                 /* physical address of this descriptor */
3117                 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3118
3119                 /* physical address of next descriptor */
3120                 if (i == info->rbuf_count - 1)
3121                         info->rbufs[i].next = cpu_to_le32(pbufs);
3122                 else
3123                         info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3124                 set_desc_count(info->rbufs[i], DMABUFSIZE);
3125         }
3126
3127         for (i=0; i < info->tbuf_count; i++) {
3128                 /* physical address of this descriptor */
3129                 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3130
3131                 /* physical address of next descriptor */
3132                 if (i == info->tbuf_count - 1)
3133                         info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3134                 else
3135                         info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3136         }
3137
3138         return 0;
3139 }
3140
3141 static void free_desc(struct slgt_info *info)
3142 {
3143         if (info->bufs != NULL) {
3144                 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3145                 info->bufs  = NULL;
3146                 info->rbufs = NULL;
3147                 info->tbufs = NULL;
3148         }
3149 }
3150
3151 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3152 {
3153         int i;
3154         for (i=0; i < count; i++) {
3155                 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3156                         return -ENOMEM;
3157                 bufs[i].pbuf  = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3158         }
3159         return 0;
3160 }
3161
3162 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3163 {
3164         int i;
3165         for (i=0; i < count; i++) {
3166                 if (bufs[i].buf == NULL)
3167                         continue;
3168                 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3169                 bufs[i].buf = NULL;
3170         }
3171 }
3172
3173 static int alloc_dma_bufs(struct slgt_info *info)
3174 {
3175         info->rbuf_count = 32;
3176         info->tbuf_count = 32;
3177
3178         if (alloc_desc(info) < 0 ||
3179             alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3180             alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3181             alloc_tmp_rbuf(info) < 0) {
3182                 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3183                 return -ENOMEM;
3184         }
3185         reset_rbufs(info);
3186         return 0;
3187 }
3188
3189 static void free_dma_bufs(struct slgt_info *info)
3190 {
3191         if (info->bufs) {
3192                 free_bufs(info, info->rbufs, info->rbuf_count);
3193                 free_bufs(info, info->tbufs, info->tbuf_count);
3194                 free_desc(info);
3195         }
3196         free_tmp_rbuf(info);
3197 }
3198
3199 static int claim_resources(struct slgt_info *info)
3200 {
3201         if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3202                 DBGERR(("%s reg addr conflict, addr=%08X\n",
3203                         info->device_name, info->phys_reg_addr));
3204                 info->init_error = DiagStatus_AddressConflict;
3205                 goto errout;
3206         }
3207         else
3208                 info->reg_addr_requested = 1;
3209
3210         info->reg_addr = ioremap(info->phys_reg_addr, SLGT_REG_SIZE);
3211         if (!info->reg_addr) {
3212                 DBGERR(("%s cant map device registers, addr=%08X\n",
3213                         info->device_name, info->phys_reg_addr));
3214                 info->init_error = DiagStatus_CantAssignPciResources;
3215                 goto errout;
3216         }
3217         return 0;
3218
3219 errout:
3220         release_resources(info);
3221         return -ENODEV;
3222 }
3223
3224 static void release_resources(struct slgt_info *info)
3225 {
3226         if (info->irq_requested) {
3227                 free_irq(info->irq_level, info);
3228                 info->irq_requested = 0;
3229         }
3230
3231         if (info->reg_addr_requested) {
3232                 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3233                 info->reg_addr_requested = 0;
3234         }
3235
3236         if (info->reg_addr) {
3237                 iounmap(info->reg_addr);
3238                 info->reg_addr = NULL;
3239         }
3240 }
3241
3242 /* Add the specified device instance data structure to the
3243  * global linked list of devices and increment the device count.
3244  */
3245 static void add_device(struct slgt_info *info)
3246 {
3247         char *devstr;
3248
3249         info->next_device = NULL;
3250         info->line = slgt_device_count;
3251         sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3252
3253         if (info->line < MAX_DEVICES) {
3254                 if (maxframe[info->line])
3255                         info->max_frame_size = maxframe[info->line];
3256                 info->dosyncppp = dosyncppp[info->line];
3257         }
3258
3259         slgt_device_count++;
3260
3261         if (!slgt_device_list)
3262                 slgt_device_list = info;
3263         else {
3264                 struct slgt_info *current_dev = slgt_device_list;
3265                 while(current_dev->next_device)
3266                         current_dev = current_dev->next_device;
3267                 current_dev->next_device = info;
3268         }
3269
3270         if (info->max_frame_size < 4096)
3271                 info->max_frame_size = 4096;
3272         else if (info->max_frame_size > 65535)
3273                 info->max_frame_size = 65535;
3274
3275         switch(info->pdev->device) {
3276         case SYNCLINK_GT_DEVICE_ID:
3277                 devstr = "GT";
3278                 break;
3279         case SYNCLINK_GT4_DEVICE_ID:
3280                 devstr = "GT4";
3281                 break;
3282         case SYNCLINK_AC_DEVICE_ID:
3283                 devstr = "AC";
3284                 info->params.mode = MGSL_MODE_ASYNC;
3285                 break;
3286         default:
3287                 devstr = "(unknown model)";
3288         }
3289         printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3290                 devstr, info->device_name, info->phys_reg_addr,
3291                 info->irq_level, info->max_frame_size);
3292
3293 #ifdef CONFIG_HDLC
3294         hdlcdev_init(info);
3295 #endif
3296 }
3297
3298 /*
3299  *  allocate device instance structure, return NULL on failure
3300  */
3301 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3302 {
3303         struct slgt_info *info;
3304
3305         info = kmalloc(sizeof(struct slgt_info), GFP_KERNEL);
3306
3307         if (!info) {
3308                 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3309                         driver_name, adapter_num, port_num));
3310         } else {
3311                 memset(info, 0, sizeof(struct slgt_info));
3312                 info->magic = MGSL_MAGIC;
3313                 INIT_WORK(&info->task, bh_handler, info);
3314                 info->max_frame_size = 4096;
3315                 info->raw_rx_size = DMABUFSIZE;
3316                 info->close_delay = 5*HZ/10;
3317                 info->closing_wait = 30*HZ;
3318                 init_waitqueue_head(&info->open_wait);
3319                 init_waitqueue_head(&info->close_wait);
3320                 init_waitqueue_head(&info->status_event_wait_q);
3321                 init_waitqueue_head(&info->event_wait_q);
3322                 spin_lock_init(&info->netlock);
3323                 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3324                 info->idle_mode = HDLC_TXIDLE_FLAGS;
3325                 info->adapter_num = adapter_num;
3326                 info->port_num = port_num;
3327
3328                 init_timer(&info->tx_timer);
3329                 info->tx_timer.data = (unsigned long)info;
3330                 info->tx_timer.function = tx_timeout;
3331
3332                 init_timer(&info->rx_timer);
3333                 info->rx_timer.data = (unsigned long)info;
3334                 info->rx_timer.function = rx_timeout;
3335
3336                 /* Copy configuration info to device instance data */
3337                 info->pdev = pdev;
3338                 info->irq_level = pdev->irq;
3339                 info->phys_reg_addr = pci_resource_start(pdev,0);
3340
3341                 info->bus_type = MGSL_BUS_TYPE_PCI;
3342                 info->irq_flags = SA_SHIRQ;
3343
3344                 info->init_error = -1; /* assume error, set to 0 on successful init */
3345         }
3346
3347         return info;
3348 }
3349
3350 static void device_init(int adapter_num, struct pci_dev *pdev)
3351 {
3352         struct slgt_info *port_array[SLGT_MAX_PORTS];
3353         int i;
3354         int port_count = 1;
3355
3356         if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3357                 port_count = 4;
3358
3359         /* allocate device instances for all ports */
3360         for (i=0; i < port_count; ++i) {
3361                 port_array[i] = alloc_dev(adapter_num, i, pdev);
3362                 if (port_array[i] == NULL) {
3363                         for (--i; i >= 0; --i)
3364                                 kfree(port_array[i]);
3365                         return;
3366                 }
3367         }
3368
3369         /* give copy of port_array to all ports and add to device list  */
3370         for (i=0; i < port_count; ++i) {
3371                 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3372                 add_device(port_array[i]);
3373                 port_array[i]->port_count = port_count;
3374                 spin_lock_init(&port_array[i]->lock);
3375         }
3376
3377         /* Allocate and claim adapter resources */
3378         if (!claim_resources(port_array[0])) {
3379
3380                 alloc_dma_bufs(port_array[0]);
3381
3382                 /* copy resource information from first port to others */
3383                 for (i = 1; i < port_count; ++i) {
3384                         port_array[i]->lock      = port_array[0]->lock;
3385                         port_array[i]->irq_level = port_array[0]->irq_level;
3386                         port_array[i]->reg_addr  = port_array[0]->reg_addr;
3387                         alloc_dma_bufs(port_array[i]);
3388                 }
3389
3390                 if (request_irq(port_array[0]->irq_level,
3391                                         slgt_interrupt,
3392                                         port_array[0]->irq_flags,
3393                                         port_array[0]->device_name,
3394                                         port_array[0]) < 0) {
3395                         DBGERR(("%s request_irq failed IRQ=%d\n",
3396                                 port_array[0]->device_name,
3397                                 port_array[0]->irq_level));
3398                 } else {
3399                         port_array[0]->irq_requested = 1;
3400                         adapter_test(port_array[0]);
3401                         for (i=1 ; i < port_count ; i++) {
3402                                 port_array[i]->init_error = port_array[0]->init_error;
3403                                 port_array[i]->gpio_present = port_array[0]->gpio_present;
3404                         }
3405                 }
3406         }
3407 }
3408
3409 static int __devinit init_one(struct pci_dev *dev,
3410                               const struct pci_device_id *ent)
3411 {
3412         if (pci_enable_device(dev)) {
3413                 printk("error enabling pci device %p\n", dev);
3414                 return -EIO;
3415         }
3416         pci_set_master(dev);
3417         device_init(slgt_device_count, dev);
3418         return 0;
3419 }
3420
3421 static void __devexit remove_one(struct pci_dev *dev)
3422 {
3423 }
3424
3425 static struct tty_operations ops = {
3426         .open = open,
3427         .close = close,
3428         .write = write,
3429         .put_char = put_char,
3430         .flush_chars = flush_chars,
3431         .write_room = write_room,
3432         .chars_in_buffer = chars_in_buffer,
3433         .flush_buffer = flush_buffer,
3434         .ioctl = ioctl,
3435         .throttle = throttle,
3436         .unthrottle = unthrottle,
3437         .send_xchar = send_xchar,
3438         .break_ctl = set_break,
3439         .wait_until_sent = wait_until_sent,
3440         .read_proc = read_proc,
3441         .set_termios = set_termios,
3442         .stop = tx_hold,
3443         .start = tx_release,
3444         .hangup = hangup,
3445         .tiocmget = tiocmget,
3446         .tiocmset = tiocmset,
3447 };
3448
3449 static void slgt_cleanup(void)
3450 {
3451         int rc;
3452         struct slgt_info *info;
3453         struct slgt_info *tmp;
3454
3455         printk("unload %s %s\n", driver_name, driver_version);
3456
3457         if (serial_driver) {
3458                 if ((rc = tty_unregister_driver(serial_driver)))
3459                         DBGERR(("tty_unregister_driver error=%d\n", rc));
3460                 put_tty_driver(serial_driver);
3461         }
3462
3463         /* reset devices */
3464         info = slgt_device_list;
3465         while(info) {
3466                 reset_port(info);
3467                 info = info->next_device;
3468         }
3469
3470         /* release devices */
3471         info = slgt_device_list;
3472         while(info) {
3473 #ifdef CONFIG_HDLC
3474                 hdlcdev_exit(info);
3475 #endif
3476                 free_dma_bufs(info);
3477                 free_tmp_rbuf(info);
3478                 if (info->port_num == 0)
3479                         release_resources(info);
3480                 tmp = info;
3481                 info = info->next_device;
3482                 kfree(tmp);
3483         }
3484
3485         if (pci_registered)
3486                 pci_unregister_driver(&pci_driver);
3487 }
3488
3489 /*
3490  *  Driver initialization entry point.
3491  */
3492 static int __init slgt_init(void)
3493 {
3494         int rc;
3495
3496         printk("%s %s\n", driver_name, driver_version);
3497
3498         slgt_device_count = 0;
3499         if ((rc = pci_register_driver(&pci_driver)) < 0) {
3500                 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3501                 return rc;
3502         }
3503         pci_registered = 1;
3504
3505         if (!slgt_device_list) {
3506                 printk("%s no devices found\n",driver_name);
3507                 return -ENODEV;
3508         }
3509
3510         serial_driver = alloc_tty_driver(MAX_DEVICES);
3511         if (!serial_driver) {
3512                 rc = -ENOMEM;
3513                 goto error;
3514         }
3515
3516         /* Initialize the tty_driver structure */
3517
3518         serial_driver->owner = THIS_MODULE;
3519         serial_driver->driver_name = tty_driver_name;
3520         serial_driver->name = tty_dev_prefix;
3521         serial_driver->major = ttymajor;
3522         serial_driver->minor_start = 64;
3523         serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3524         serial_driver->subtype = SERIAL_TYPE_NORMAL;
3525         serial_driver->init_termios = tty_std_termios;
3526         serial_driver->init_termios.c_cflag =
3527                 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3528         serial_driver->flags = TTY_DRIVER_REAL_RAW;
3529         tty_set_operations(serial_driver, &ops);
3530         if ((rc = tty_register_driver(serial_driver)) < 0) {
3531                 DBGERR(("%s can't register serial driver\n", driver_name));
3532                 put_tty_driver(serial_driver);
3533                 serial_driver = NULL;
3534                 goto error;
3535         }
3536
3537         printk("%s %s, tty major#%d\n",
3538                 driver_name, driver_version,
3539                 serial_driver->major);
3540
3541         return 0;
3542
3543 error:
3544         slgt_cleanup();
3545         return rc;
3546 }
3547
3548 static void __exit slgt_exit(void)
3549 {
3550         slgt_cleanup();
3551 }
3552
3553 module_init(slgt_init);
3554 module_exit(slgt_exit);
3555
3556 /*
3557  * register access routines
3558  */
3559
3560 #define CALC_REGADDR() \
3561         unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3562         if (addr >= 0x80) \
3563                 reg_addr += (info->port_num) * 32;
3564
3565 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3566 {
3567         CALC_REGADDR();
3568         return readb((void __iomem *)reg_addr);
3569 }
3570
3571 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3572 {
3573         CALC_REGADDR();
3574         writeb(value, (void __iomem *)reg_addr);
3575 }
3576
3577 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3578 {
3579         CALC_REGADDR();
3580         return readw((void __iomem *)reg_addr);
3581 }
3582
3583 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3584 {
3585         CALC_REGADDR();
3586         writew(value, (void __iomem *)reg_addr);
3587 }
3588
3589 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3590 {
3591         CALC_REGADDR();
3592         return readl((void __iomem *)reg_addr);
3593 }
3594
3595 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3596 {
3597         CALC_REGADDR();
3598         writel(value, (void __iomem *)reg_addr);
3599 }
3600
3601 static void rdma_reset(struct slgt_info *info)
3602 {
3603         unsigned int i;
3604
3605         /* set reset bit */
3606         wr_reg32(info, RDCSR, BIT1);
3607
3608         /* wait for enable bit cleared */
3609         for(i=0 ; i < 1000 ; i++)
3610                 if (!(rd_reg32(info, RDCSR) & BIT0))
3611                         break;
3612 }
3613
3614 static void tdma_reset(struct slgt_info *info)
3615 {
3616         unsigned int i;
3617
3618         /* set reset bit */
3619         wr_reg32(info, TDCSR, BIT1);
3620
3621         /* wait for enable bit cleared */
3622         for(i=0 ; i < 1000 ; i++)
3623                 if (!(rd_reg32(info, TDCSR) & BIT0))
3624                         break;
3625 }
3626
3627 /*
3628  * enable internal loopback
3629  * TxCLK and RxCLK are generated from BRG
3630  * and TxD is looped back to RxD internally.
3631  */
3632 static void enable_loopback(struct slgt_info *info)
3633 {
3634         /* SCR (serial control) BIT2=looopback enable */
3635         wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3636
3637         if (info->params.mode != MGSL_MODE_ASYNC) {
3638                 /* CCR (clock control)
3639                  * 07..05  tx clock source (010 = BRG)
3640                  * 04..02  rx clock source (010 = BRG)
3641                  * 01      auxclk enable   (0 = disable)
3642                  * 00      BRG enable      (1 = enable)
3643                  *
3644                  * 0100 1001
3645                  */
3646                 wr_reg8(info, CCR, 0x49);
3647
3648                 /* set speed if available, otherwise use default */
3649                 if (info->params.clock_speed)
3650                         set_rate(info, info->params.clock_speed);
3651                 else
3652                         set_rate(info, 3686400);
3653         }
3654 }
3655
3656 /*
3657  *  set baud rate generator to specified rate
3658  */
3659 static void set_rate(struct slgt_info *info, u32 rate)
3660 {
3661         unsigned int div;
3662         static unsigned int osc = 14745600;
3663
3664         /* div = osc/rate - 1
3665          *
3666          * Round div up if osc/rate is not integer to
3667          * force to next slowest rate.
3668          */
3669
3670         if (rate) {
3671                 div = osc/rate;
3672                 if (!(osc % rate) && div)
3673                         div--;
3674                 wr_reg16(info, BDR, (unsigned short)div);
3675         }
3676 }
3677
3678 static void rx_stop(struct slgt_info *info)
3679 {
3680         unsigned short val;
3681
3682         /* disable and reset receiver */
3683         val = rd_reg16(info, RCR) & ~BIT1;          /* clear enable bit */
3684         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3685         wr_reg16(info, RCR, val);                  /* clear reset bit */
3686
3687         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3688
3689         /* clear pending rx interrupts */
3690         wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3691
3692         rdma_reset(info);
3693
3694         info->rx_enabled = 0;
3695         info->rx_restart = 0;
3696 }
3697
3698 static void rx_start(struct slgt_info *info)
3699 {
3700         unsigned short val;
3701
3702         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3703
3704         /* clear pending rx overrun IRQ */
3705         wr_reg16(info, SSR, IRQ_RXOVER);
3706
3707         /* reset and disable receiver */
3708         val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3709         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3710         wr_reg16(info, RCR, val);                  /* clear reset bit */
3711
3712         rdma_reset(info);
3713         reset_rbufs(info);
3714
3715         /* set 1st descriptor address */
3716         wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
3717
3718         if (info->params.mode != MGSL_MODE_ASYNC) {
3719                 /* enable rx DMA and DMA interrupt */
3720                 wr_reg32(info, RDCSR, (BIT2 + BIT0));
3721         } else {
3722                 /* enable saving of rx status, rx DMA and DMA interrupt */
3723                 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
3724         }
3725
3726         slgt_irq_on(info, IRQ_RXOVER);
3727
3728         /* enable receiver */
3729         wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
3730
3731         info->rx_restart = 0;
3732         info->rx_enabled = 1;
3733 }
3734
3735 static void tx_start(struct slgt_info *info)
3736 {
3737         if (!info->tx_enabled) {
3738                 wr_reg16(info, TCR,
3739                         (unsigned short)(rd_reg16(info, TCR) | BIT1));
3740                 info->tx_enabled = TRUE;
3741         }
3742
3743         if (info->tx_count) {
3744                 info->drop_rts_on_tx_done = 0;
3745
3746                 if (info->params.mode != MGSL_MODE_ASYNC) {
3747                         if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
3748                                 get_signals(info);
3749                                 if (!(info->signals & SerialSignal_RTS)) {
3750                                         info->signals |= SerialSignal_RTS;
3751                                         set_signals(info);
3752                                         info->drop_rts_on_tx_done = 1;
3753                                 }
3754                         }
3755
3756                         slgt_irq_off(info, IRQ_TXDATA);
3757                         slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
3758                         /* clear tx idle and underrun status bits */
3759                         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3760
3761                         if (!(rd_reg32(info, TDCSR) & BIT0)) {
3762                                 /* tx DMA stopped, restart tx DMA */
3763                                 tdma_reset(info);
3764                                 /* set 1st descriptor address */
3765                                 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3766                                 if (info->params.mode == MGSL_MODE_RAW)
3767                                         wr_reg32(info, TDCSR, BIT2 + BIT0); /* IRQ + DMA enable */
3768                                 else
3769                                         wr_reg32(info, TDCSR, BIT0); /* DMA enable */
3770                         }
3771
3772                         if (info->params.mode != MGSL_MODE_RAW) {
3773                                 info->tx_timer.expires = jiffies + msecs_to_jiffies(5000);
3774                                 add_timer(&info->tx_timer);
3775                         }
3776                 } else {
3777                         tdma_reset(info);
3778                         /* set 1st descriptor address */
3779                         wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3780
3781                         slgt_irq_off(info, IRQ_TXDATA);
3782                         slgt_irq_on(info, IRQ_TXIDLE);
3783                         /* clear tx idle status bit */
3784                         wr_reg16(info, SSR, IRQ_TXIDLE);
3785
3786                         /* enable tx DMA */
3787                         wr_reg32(info, TDCSR, BIT0);
3788                 }
3789
3790                 info->tx_active = 1;
3791         }
3792 }
3793
3794 static void tx_stop(struct slgt_info *info)
3795 {
3796         unsigned short val;
3797
3798         del_timer(&info->tx_timer);
3799
3800         tdma_reset(info);
3801
3802         /* reset and disable transmitter */
3803         val = rd_reg16(info, TCR) & ~BIT1;          /* clear enable bit */
3804         wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
3805         wr_reg16(info, TCR, val);                  /* clear reset */
3806
3807         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
3808
3809         /* clear tx idle and underrun status bit */
3810         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3811
3812         reset_tbufs(info);
3813
3814         info->tx_enabled = 0;
3815         info->tx_active  = 0;
3816 }
3817
3818 static void reset_port(struct slgt_info *info)
3819 {
3820         if (!info->reg_addr)
3821                 return;
3822
3823         tx_stop(info);
3824         rx_stop(info);
3825
3826         info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
3827         set_signals(info);
3828
3829         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3830 }
3831
3832 static void reset_adapter(struct slgt_info *info)
3833 {
3834         int i;
3835         for (i=0; i < info->port_count; ++i) {
3836                 if (info->port_array[i])
3837                         reset_port(info->port_array[i]);
3838         }
3839 }
3840
3841 static void async_mode(struct slgt_info *info)
3842 {
3843         unsigned short val;
3844
3845         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3846         tx_stop(info);
3847         rx_stop(info);
3848
3849         /* TCR (tx control)
3850          *
3851          * 15..13  mode, 010=async
3852          * 12..10  encoding, 000=NRZ
3853          * 09      parity enable
3854          * 08      1=odd parity, 0=even parity
3855          * 07      1=RTS driver control
3856          * 06      1=break enable
3857          * 05..04  character length
3858          *         00=5 bits
3859          *         01=6 bits
3860          *         10=7 bits
3861          *         11=8 bits
3862          * 03      0=1 stop bit, 1=2 stop bits
3863          * 02      reset
3864          * 01      enable
3865          * 00      auto-CTS enable
3866          */
3867         val = 0x4000;
3868
3869         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
3870                 val |= BIT7;
3871
3872         if (info->params.parity != ASYNC_PARITY_NONE) {
3873                 val |= BIT9;
3874                 if (info->params.parity == ASYNC_PARITY_ODD)
3875                         val |= BIT8;
3876         }
3877
3878         switch (info->params.data_bits)
3879         {
3880         case 6: val |= BIT4; break;
3881         case 7: val |= BIT5; break;
3882         case 8: val |= BIT5 + BIT4; break;
3883         }
3884
3885         if (info->params.stop_bits != 1)
3886                 val |= BIT3;
3887
3888         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
3889                 val |= BIT0;
3890
3891         wr_reg16(info, TCR, val);
3892
3893         /* RCR (rx control)
3894          *
3895          * 15..13  mode, 010=async
3896          * 12..10  encoding, 000=NRZ
3897          * 09      parity enable
3898          * 08      1=odd parity, 0=even parity
3899          * 07..06  reserved, must be 0
3900          * 05..04  character length
3901          *         00=5 bits
3902          *         01=6 bits
3903          *         10=7 bits
3904          *         11=8 bits
3905          * 03      reserved, must be zero
3906          * 02      reset
3907          * 01      enable
3908          * 00      auto-DCD enable
3909          */
3910         val = 0x4000;
3911
3912         if (info->params.parity != ASYNC_PARITY_NONE) {
3913                 val |= BIT9;
3914                 if (info->params.parity == ASYNC_PARITY_ODD)
3915                         val |= BIT8;
3916         }
3917
3918         switch (info->params.data_bits)
3919         {
3920         case 6: val |= BIT4; break;
3921         case 7: val |= BIT5; break;
3922         case 8: val |= BIT5 + BIT4; break;
3923         }
3924
3925         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
3926                 val |= BIT0;
3927
3928         wr_reg16(info, RCR, val);
3929
3930         /* CCR (clock control)
3931          *
3932          * 07..05  011 = tx clock source is BRG/16
3933          * 04..02  010 = rx clock source is BRG
3934          * 01      0 = auxclk disabled
3935          * 00      1 = BRG enabled
3936          *
3937          * 0110 1001
3938          */
3939         wr_reg8(info, CCR, 0x69);
3940
3941         msc_set_vcr(info);
3942
3943         tx_set_idle(info);
3944
3945         /* SCR (serial control)
3946          *
3947          * 15  1=tx req on FIFO half empty
3948          * 14  1=rx req on FIFO half full
3949          * 13  tx data  IRQ enable
3950          * 12  tx idle  IRQ enable
3951          * 11  rx break on IRQ enable
3952          * 10  rx data  IRQ enable
3953          * 09  rx break off IRQ enable
3954          * 08  overrun  IRQ enable
3955          * 07  DSR      IRQ enable
3956          * 06  CTS      IRQ enable
3957          * 05  DCD      IRQ enable
3958          * 04  RI       IRQ enable
3959          * 03  reserved, must be zero
3960          * 02  1=txd->rxd internal loopback enable
3961          * 01  reserved, must be zero
3962          * 00  1=master IRQ enable
3963          */
3964         val = BIT15 + BIT14 + BIT0;
3965         wr_reg16(info, SCR, val);
3966
3967         slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
3968
3969         set_rate(info, info->params.data_rate * 16);
3970
3971         if (info->params.loopback)
3972                 enable_loopback(info);
3973 }
3974
3975 static void hdlc_mode(struct slgt_info *info)
3976 {
3977         unsigned short val;
3978
3979         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3980         tx_stop(info);
3981         rx_stop(info);
3982
3983         /* TCR (tx control)
3984          *
3985          * 15..13  mode, 000=HDLC 001=raw sync
3986          * 12..10  encoding
3987          * 09      CRC enable
3988          * 08      CRC32
3989          * 07      1=RTS driver control
3990          * 06      preamble enable
3991          * 05..04  preamble length
3992          * 03      share open/close flag
3993          * 02      reset
3994          * 01      enable
3995          * 00      auto-CTS enable
3996          */
3997         val = 0;
3998
3999         if (info->params.mode == MGSL_MODE_RAW)
4000                 val |= BIT13;
4001         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4002                 val |= BIT7;
4003
4004         switch(info->params.encoding)
4005         {
4006         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4007         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4008         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4009         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4010         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4011         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4012         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4013         }
4014
4015         switch (info->params.crc_type)
4016         {
4017         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4018         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4019         }
4020
4021         if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4022                 val |= BIT6;
4023
4024         switch (info->params.preamble_length)
4025         {
4026         case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4027         case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4028         case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4029         }
4030
4031         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4032                 val |= BIT0;
4033
4034         wr_reg16(info, TCR, val);
4035
4036         /* TPR (transmit preamble) */
4037
4038         switch (info->params.preamble)
4039         {
4040         case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4041         case HDLC_PREAMBLE_PATTERN_ONES:  val = 0xff; break;
4042         case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4043         case HDLC_PREAMBLE_PATTERN_10:    val = 0x55; break;
4044         case HDLC_PREAMBLE_PATTERN_01:    val = 0xaa; break;
4045         default:                          val = 0x7e; break;
4046         }
4047         wr_reg8(info, TPR, (unsigned char)val);
4048
4049         /* RCR (rx control)
4050          *
4051          * 15..13  mode, 000=HDLC 001=raw sync
4052          * 12..10  encoding
4053          * 09      CRC enable
4054          * 08      CRC32
4055          * 07..03  reserved, must be 0
4056          * 02      reset
4057          * 01      enable
4058          * 00      auto-DCD enable
4059          */
4060         val = 0;
4061
4062         if (info->params.mode == MGSL_MODE_RAW)
4063                 val |= BIT13;
4064
4065         switch(info->params.encoding)
4066         {
4067         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4068         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4069         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4070         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4071         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4072         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4073         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4074         }
4075
4076         switch (info->params.crc_type)
4077         {
4078         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4079         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4080         }
4081
4082         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4083                 val |= BIT0;
4084
4085         wr_reg16(info, RCR, val);
4086
4087         /* CCR (clock control)
4088          *
4089          * 07..05  tx clock source
4090          * 04..02  rx clock source
4091          * 01      auxclk enable
4092          * 00      BRG enable
4093          */
4094         val = 0;
4095
4096         if (info->params.flags & HDLC_FLAG_TXC_BRG)
4097         {
4098                 // when RxC source is DPLL, BRG generates 16X DPLL
4099                 // reference clock, so take TxC from BRG/16 to get
4100                 // transmit clock at actual data rate
4101                 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4102                         val |= BIT6 + BIT5;     /* 011, txclk = BRG/16 */
4103                 else
4104                         val |= BIT6;    /* 010, txclk = BRG */
4105         }
4106         else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4107                 val |= BIT7;    /* 100, txclk = DPLL Input */
4108         else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4109                 val |= BIT5;    /* 001, txclk = RXC Input */
4110
4111         if (info->params.flags & HDLC_FLAG_RXC_BRG)
4112                 val |= BIT3;    /* 010, rxclk = BRG */
4113         else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4114                 val |= BIT4;    /* 100, rxclk = DPLL */
4115         else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4116                 val |= BIT2;    /* 001, rxclk = TXC Input */
4117
4118         if (info->params.clock_speed)
4119                 val |= BIT1 + BIT0;
4120
4121         wr_reg8(info, CCR, (unsigned char)val);
4122
4123         if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4124         {
4125                 // program DPLL mode
4126                 switch(info->params.encoding)
4127                 {
4128                 case HDLC_ENCODING_BIPHASE_MARK:
4129                 case HDLC_ENCODING_BIPHASE_SPACE:
4130                         val = BIT7; break;
4131                 case HDLC_ENCODING_BIPHASE_LEVEL:
4132                 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4133                         val = BIT7 + BIT6; break;
4134                 default: val = BIT6;    // NRZ encodings
4135                 }
4136                 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4137
4138                 // DPLL requires a 16X reference clock from BRG
4139                 set_rate(info, info->params.clock_speed * 16);
4140         }
4141         else
4142                 set_rate(info, info->params.clock_speed);
4143
4144         tx_set_idle(info);
4145
4146         msc_set_vcr(info);
4147
4148         /* SCR (serial control)
4149          *
4150          * 15  1=tx req on FIFO half empty
4151          * 14  1=rx req on FIFO half full
4152          * 13  tx data  IRQ enable
4153          * 12  tx idle  IRQ enable
4154          * 11  underrun IRQ enable
4155          * 10  rx data  IRQ enable
4156          * 09  rx idle  IRQ enable
4157          * 08  overrun  IRQ enable
4158          * 07  DSR      IRQ enable
4159          * 06  CTS      IRQ enable
4160          * 05  DCD      IRQ enable
4161          * 04  RI       IRQ enable
4162          * 03  reserved, must be zero
4163          * 02  1=txd->rxd internal loopback enable
4164          * 01  reserved, must be zero
4165          * 00  1=master IRQ enable
4166          */
4167         wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4168
4169         if (info->params.loopback)
4170                 enable_loopback(info);
4171 }
4172
4173 /*
4174  *  set transmit idle mode
4175  */
4176 static void tx_set_idle(struct slgt_info *info)
4177 {
4178         unsigned char val = 0xff;
4179
4180         switch(info->idle_mode)
4181         {
4182         case HDLC_TXIDLE_FLAGS:          val = 0x7e; break;
4183         case HDLC_TXIDLE_ALT_ZEROS_ONES: val = 0xaa; break;
4184         case HDLC_TXIDLE_ZEROS:          val = 0x00; break;
4185         case HDLC_TXIDLE_ONES:           val = 0xff; break;
4186         case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4187         case HDLC_TXIDLE_SPACE:          val = 0x00; break;
4188         case HDLC_TXIDLE_MARK:           val = 0xff; break;
4189         }
4190
4191         wr_reg8(info, TIR, val);
4192 }
4193
4194 /*
4195  * get state of V24 status (input) signals
4196  */
4197 static void get_signals(struct slgt_info *info)
4198 {
4199         unsigned short status = rd_reg16(info, SSR);
4200
4201         /* clear all serial signals except DTR and RTS */
4202         info->signals &= SerialSignal_DTR + SerialSignal_RTS;
4203
4204         if (status & BIT3)
4205                 info->signals |= SerialSignal_DSR;
4206         if (status & BIT2)
4207                 info->signals |= SerialSignal_CTS;
4208         if (status & BIT1)
4209                 info->signals |= SerialSignal_DCD;
4210         if (status & BIT0)
4211                 info->signals |= SerialSignal_RI;
4212 }
4213
4214 /*
4215  * set V.24 Control Register based on current configuration
4216  */
4217 static void msc_set_vcr(struct slgt_info *info)
4218 {
4219         unsigned char val = 0;
4220
4221         /* VCR (V.24 control)
4222          *
4223          * 07..04  serial IF select
4224          * 03      DTR
4225          * 02      RTS
4226          * 01      LL
4227          * 00      RL
4228          */
4229
4230         switch(info->if_mode & MGSL_INTERFACE_MASK)
4231         {
4232         case MGSL_INTERFACE_RS232:
4233                 val |= BIT5; /* 0010 */
4234                 break;
4235         case MGSL_INTERFACE_V35:
4236                 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4237                 break;
4238         case MGSL_INTERFACE_RS422:
4239                 val |= BIT6; /* 0100 */
4240                 break;
4241         }
4242
4243         if (info->signals & SerialSignal_DTR)
4244                 val |= BIT3;
4245         if (info->signals & SerialSignal_RTS)
4246                 val |= BIT2;
4247         if (info->if_mode & MGSL_INTERFACE_LL)
4248                 val |= BIT1;
4249         if (info->if_mode & MGSL_INTERFACE_RL)
4250                 val |= BIT0;
4251         wr_reg8(info, VCR, val);
4252 }
4253
4254 /*
4255  * set state of V24 control (output) signals
4256  */
4257 static void set_signals(struct slgt_info *info)
4258 {
4259         unsigned char val = rd_reg8(info, VCR);
4260         if (info->signals & SerialSignal_DTR)
4261                 val |= BIT3;
4262         else
4263                 val &= ~BIT3;
4264         if (info->signals & SerialSignal_RTS)
4265                 val |= BIT2;
4266         else
4267                 val &= ~BIT2;
4268         wr_reg8(info, VCR, val);
4269 }
4270
4271 /*
4272  * free range of receive DMA buffers (i to last)
4273  */
4274 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4275 {
4276         int done = 0;
4277
4278         while(!done) {
4279                 /* reset current buffer for reuse */
4280                 info->rbufs[i].status = 0;
4281                 if (info->params.mode == MGSL_MODE_RAW)
4282                         set_desc_count(info->rbufs[i], info->raw_rx_size);
4283                 else
4284                         set_desc_count(info->rbufs[i], DMABUFSIZE);
4285
4286                 if (i == last)
4287                         done = 1;
4288                 if (++i == info->rbuf_count)
4289                         i = 0;
4290         }
4291         info->rbuf_current = i;
4292 }
4293
4294 /*
4295  * mark all receive DMA buffers as free
4296  */
4297 static void reset_rbufs(struct slgt_info *info)
4298 {
4299         free_rbufs(info, 0, info->rbuf_count - 1);
4300 }
4301
4302 /*
4303  * pass receive HDLC frame to upper layer
4304  *
4305  * return 1 if frame available, otherwise 0
4306  */
4307 static int rx_get_frame(struct slgt_info *info)
4308 {
4309         unsigned int start, end;
4310         unsigned short status;
4311         unsigned int framesize = 0;
4312         int rc = 0;
4313         unsigned long flags;
4314         struct tty_struct *tty = info->tty;
4315         unsigned char addr_field = 0xff;
4316
4317 check_again:
4318
4319         framesize = 0;
4320         addr_field = 0xff;
4321         start = end = info->rbuf_current;
4322
4323         for (;;) {
4324                 if (!desc_complete(info->rbufs[end]))
4325                         goto cleanup;
4326
4327                 if (framesize == 0 && info->params.addr_filter != 0xff)
4328                         addr_field = info->rbufs[end].buf[0];
4329
4330                 framesize += desc_count(info->rbufs[end]);
4331
4332                 if (desc_eof(info->rbufs[end]))
4333                         break;
4334
4335                 if (++end == info->rbuf_count)
4336                         end = 0;
4337
4338                 if (end == info->rbuf_current) {
4339                         if (info->rx_enabled){
4340                                 spin_lock_irqsave(&info->lock,flags);
4341                                 rx_start(info);
4342                                 spin_unlock_irqrestore(&info->lock,flags);
4343                         }
4344                         goto cleanup;
4345                 }
4346         }
4347
4348         /* status
4349          *
4350          * 15      buffer complete
4351          * 14..06  reserved
4352          * 05..04  residue
4353          * 02      eof (end of frame)
4354          * 01      CRC error
4355          * 00      abort
4356          */
4357         status = desc_status(info->rbufs[end]);
4358
4359         /* ignore CRC bit if not using CRC (bit is undefined) */
4360         if (info->params.crc_type == HDLC_CRC_NONE)
4361                 status &= ~BIT1;
4362
4363         if (framesize == 0 ||
4364                  (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4365                 free_rbufs(info, start, end);
4366                 goto check_again;
4367         }
4368
4369         if (framesize < 2 || status & (BIT1+BIT0)) {
4370                 if (framesize < 2 || (status & BIT0))
4371                         info->icount.rxshort++;
4372                 else
4373                         info->icount.rxcrc++;
4374                 framesize = 0;
4375
4376 #ifdef CONFIG_HDLC
4377                 {
4378                         struct net_device_stats *stats = hdlc_stats(info->netdev);
4379                         stats->rx_errors++;
4380                         stats->rx_frame_errors++;
4381                 }
4382 #endif
4383         } else {
4384                 /* adjust frame size for CRC, if any */
4385                 if (info->params.crc_type == HDLC_CRC_16_CCITT)
4386                         framesize -= 2;
4387                 else if (info->params.crc_type == HDLC_CRC_32_CCITT)
4388                         framesize -= 4;
4389         }
4390
4391         DBGBH(("%s rx frame status=%04X size=%d\n",
4392                 info->device_name, status, framesize));
4393         DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, DMABUFSIZE), "rx");
4394
4395         if (framesize) {
4396                 if (framesize > info->max_frame_size)
4397                         info->icount.rxlong++;
4398                 else {
4399                         /* copy dma buffer(s) to contiguous temp buffer */
4400                         int copy_count = framesize;
4401                         int i = start;
4402                         unsigned char *p = info->tmp_rbuf;
4403                         info->tmp_rbuf_count = framesize;
4404
4405                         info->icount.rxok++;
4406
4407                         while(copy_count) {
4408                                 int partial_count = min(copy_count, DMABUFSIZE);
4409                                 memcpy(p, info->rbufs[i].buf, partial_count);
4410                                 p += partial_count;
4411                                 copy_count -= partial_count;
4412                                 if (++i == info->rbuf_count)
4413                                         i = 0;
4414                         }
4415
4416 #ifdef CONFIG_HDLC
4417                         if (info->netcount)
4418                                 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4419                         else
4420 #endif
4421                                 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4422                 }
4423         }
4424         free_rbufs(info, start, end);
4425         rc = 1;
4426
4427 cleanup:
4428         return rc;
4429 }
4430
4431 /*
4432  * pass receive buffer (RAW synchronous mode) to tty layer
4433  * return 1 if buffer available, otherwise 0
4434  */
4435 static int rx_get_buf(struct slgt_info *info)
4436 {
4437         unsigned int i = info->rbuf_current;
4438
4439         if (!desc_complete(info->rbufs[i]))
4440                 return 0;
4441         DBGDATA(info, info->rbufs[i].buf, desc_count(info->rbufs[i]), "rx");
4442         DBGINFO(("rx_get_buf size=%d\n", desc_count(info->rbufs[i])));
4443         ldisc_receive_buf(info->tty, info->rbufs[i].buf,
4444                           info->flag_buf, desc_count(info->rbufs[i]));
4445         free_rbufs(info, i, i);
4446         return 1;
4447 }
4448
4449 static void reset_tbufs(struct slgt_info *info)
4450 {
4451         unsigned int i;
4452         info->tbuf_current = 0;
4453         for (i=0 ; i < info->tbuf_count ; i++) {
4454                 info->tbufs[i].status = 0;
4455                 info->tbufs[i].count  = 0;
4456         }
4457 }
4458
4459 /*
4460  * return number of free transmit DMA buffers
4461  */
4462 static unsigned int free_tbuf_count(struct slgt_info *info)
4463 {
4464         unsigned int count = 0;
4465         unsigned int i = info->tbuf_current;
4466
4467         do
4468         {
4469                 if (desc_count(info->tbufs[i]))
4470                         break; /* buffer in use */
4471                 ++count;
4472                 if (++i == info->tbuf_count)
4473                         i=0;
4474         } while (i != info->tbuf_current);
4475
4476         /* last buffer with zero count may be in use, assume it is */
4477         if (count)
4478                 --count;
4479
4480         return count;
4481 }
4482
4483 /*
4484  * load transmit DMA buffer(s) with data
4485  */
4486 static void tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4487 {
4488         unsigned short count;
4489         unsigned int i;
4490         struct slgt_desc *d;
4491
4492         if (size == 0)
4493                 return;
4494
4495         DBGDATA(info, buf, size, "tx");
4496
4497         info->tbuf_start = i = info->tbuf_current;
4498
4499         while (size) {
4500                 d = &info->tbufs[i];
4501                 if (++i == info->tbuf_count)
4502                         i = 0;
4503
4504                 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4505                 memcpy(d->buf, buf, count);
4506
4507                 size -= count;
4508                 buf  += count;
4509
4510                 if (!size && info->params.mode != MGSL_MODE_RAW)
4511                         set_desc_eof(*d, 1); /* HDLC: set EOF of last desc */
4512                 else
4513                         set_desc_eof(*d, 0);
4514
4515                 set_desc_count(*d, count);
4516         }
4517
4518         info->tbuf_current = i;
4519 }
4520
4521 static int register_test(struct slgt_info *info)
4522 {
4523         static unsigned short patterns[] =
4524                 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4525         static unsigned int count = sizeof(patterns)/sizeof(patterns[0]);
4526         unsigned int i;
4527         int rc = 0;
4528
4529         for (i=0 ; i < count ; i++) {
4530                 wr_reg16(info, TIR, patterns[i]);
4531                 wr_reg16(info, BDR, patterns[(i+1)%count]);
4532                 if ((rd_reg16(info, TIR) != patterns[i]) ||
4533                     (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4534                         rc = -ENODEV;
4535                         break;
4536                 }
4537         }
4538         info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4539         info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4540         return rc;
4541 }
4542
4543 static int irq_test(struct slgt_info *info)
4544 {
4545         unsigned long timeout;
4546         unsigned long flags;
4547         struct tty_struct *oldtty = info->tty;
4548         u32 speed = info->params.data_rate;
4549
4550         info->params.data_rate = 921600;
4551         info->tty = NULL;
4552
4553         spin_lock_irqsave(&info->lock, flags);
4554         async_mode(info);
4555         slgt_irq_on(info, IRQ_TXIDLE);
4556
4557         /* enable transmitter */
4558         wr_reg16(info, TCR,
4559                 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4560
4561         /* write one byte and wait for tx idle */
4562         wr_reg16(info, TDR, 0);
4563
4564         /* assume failure */
4565         info->init_error = DiagStatus_IrqFailure;
4566         info->irq_occurred = FALSE;
4567
4568         spin_unlock_irqrestore(&info->lock, flags);
4569
4570         timeout=100;
4571         while(timeout-- && !info->irq_occurred)
4572                 msleep_interruptible(10);
4573
4574         spin_lock_irqsave(&info->lock,flags);
4575         reset_port(info);
4576         spin_unlock_irqrestore(&info->lock,flags);
4577
4578         info->params.data_rate = speed;
4579         info->tty = oldtty;
4580
4581         info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
4582         return info->irq_occurred ? 0 : -ENODEV;
4583 }
4584
4585 static int loopback_test_rx(struct slgt_info *info)
4586 {
4587         unsigned char *src, *dest;
4588         int count;
4589
4590         if (desc_complete(info->rbufs[0])) {
4591                 count = desc_count(info->rbufs[0]);
4592                 src   = info->rbufs[0].buf;
4593                 dest  = info->tmp_rbuf;
4594
4595                 for( ; count ; count-=2, src+=2) {
4596                         /* src=data byte (src+1)=status byte */
4597                         if (!(*(src+1) & (BIT9 + BIT8))) {
4598                                 *dest = *src;
4599                                 dest++;
4600                                 info->tmp_rbuf_count++;
4601                         }
4602                 }
4603                 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
4604                 return 1;
4605         }
4606         return 0;
4607 }
4608
4609 static int loopback_test(struct slgt_info *info)
4610 {
4611 #define TESTFRAMESIZE 20
4612
4613         unsigned long timeout;
4614         u16 count = TESTFRAMESIZE;
4615         unsigned char buf[TESTFRAMESIZE];
4616         int rc = -ENODEV;
4617         unsigned long flags;
4618
4619         struct tty_struct *oldtty = info->tty;
4620         MGSL_PARAMS params;
4621
4622         memcpy(&params, &info->params, sizeof(params));
4623
4624         info->params.mode = MGSL_MODE_ASYNC;
4625         info->params.data_rate = 921600;
4626         info->params.loopback = 1;
4627         info->tty = NULL;
4628
4629         /* build and send transmit frame */
4630         for (count = 0; count < TESTFRAMESIZE; ++count)
4631                 buf[count] = (unsigned char)count;
4632
4633         info->tmp_rbuf_count = 0;
4634         memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
4635
4636         /* program hardware for HDLC and enabled receiver */
4637         spin_lock_irqsave(&info->lock,flags);
4638         async_mode(info);
4639         rx_start(info);
4640         info->tx_count = count;
4641         tx_load(info, buf, count);
4642         tx_start(info);
4643         spin_unlock_irqrestore(&info->lock, flags);
4644
4645         /* wait for receive complete */
4646         for (timeout = 100; timeout; --timeout) {
4647                 msleep_interruptible(10);
4648                 if (loopback_test_rx(info)) {
4649                         rc = 0;
4650                         break;
4651                 }
4652         }
4653
4654         /* verify received frame length and contents */
4655         if (!rc && (info->tmp_rbuf_count != count ||
4656                   memcmp(buf, info->tmp_rbuf, count))) {
4657                 rc = -ENODEV;
4658         }
4659
4660         spin_lock_irqsave(&info->lock,flags);
4661         reset_adapter(info);
4662         spin_unlock_irqrestore(&info->lock,flags);
4663
4664         memcpy(&info->params, &params, sizeof(info->params));
4665         info->tty = oldtty;
4666
4667         info->init_error = rc ? DiagStatus_DmaFailure : 0;
4668         return rc;
4669 }
4670
4671 static int adapter_test(struct slgt_info *info)
4672 {
4673         DBGINFO(("testing %s\n", info->device_name));
4674         if ((info->init_error = register_test(info)) < 0) {
4675                 printk("register test failure %s addr=%08X\n",
4676                         info->device_name, info->phys_reg_addr);
4677         } else if ((info->init_error = irq_test(info)) < 0) {
4678                 printk("IRQ test failure %s IRQ=%d\n",
4679                         info->device_name, info->irq_level);
4680         } else if ((info->init_error = loopback_test(info)) < 0) {
4681                 printk("loopback test failure %s\n", info->device_name);
4682         }
4683         return info->init_error;
4684 }
4685
4686 /*
4687  * transmit timeout handler
4688  */
4689 static void tx_timeout(unsigned long context)
4690 {
4691         struct slgt_info *info = (struct slgt_info*)context;
4692         unsigned long flags;
4693
4694         DBGINFO(("%s tx_timeout\n", info->device_name));
4695         if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
4696                 info->icount.txtimeout++;
4697         }
4698         spin_lock_irqsave(&info->lock,flags);
4699         info->tx_active = 0;
4700         info->tx_count = 0;
4701         spin_unlock_irqrestore(&info->lock,flags);
4702
4703 #ifdef CONFIG_HDLC
4704         if (info->netcount)
4705                 hdlcdev_tx_done(info);
4706         else
4707 #endif
4708                 bh_transmit(info);
4709 }
4710
4711 /*
4712  * receive buffer polling timer
4713  */
4714 static void rx_timeout(unsigned long context)
4715 {
4716         struct slgt_info *info = (struct slgt_info*)context;
4717         unsigned long flags;
4718
4719         DBGINFO(("%s rx_timeout\n", info->device_name));
4720         spin_lock_irqsave(&info->lock, flags);
4721         info->pending_bh |= BH_RECEIVE;
4722         spin_unlock_irqrestore(&info->lock, flags);
4723         bh_handler(info);
4724 }
4725