arch/powerpc/platforms/powermac/smp.c

   1 /*
   2  * SMP support for power macintosh.
   3  *
   4  * We support both the old "powersurge" SMP architecture
   5  * and the current Core99 (G4 PowerMac) machines.
   6  *
   7  * Note that we don't support the very first rev. of
   8  * Apple/DayStar 2 CPUs board, the one with the funky
   9  * watchdog. Hopefully, none of these should be there except
  10  * maybe internally to Apple. I should probably still add some
  11  * code to detect this card though and disable SMP. --BenH.
  12  *
  13  * Support Macintosh G4 SMP by Troy Benjegerdes (hozer@drgw.net)
  14  * and Ben Herrenschmidt <benh@kernel.crashing.org>.
  15  *
  16  * Support for DayStar quad CPU cards
  17  * Copyright (C) XLR8, Inc. 1994-2000
  18  *
  19  *  This program is free software; you can redistribute it and/or
  20  *  modify it under the terms of the GNU General Public License
  21  *  as published by the Free Software Foundation; either version
  22  *  2 of the License, or (at your option) any later version.
  23  */
  24 #include <linux/config.h>
  25 #include <linux/kernel.h>
  26 #include <linux/sched.h>
  27 #include <linux/smp.h>
  28 #include <linux/smp_lock.h>
  29 #include <linux/interrupt.h>
  30 #include <linux/kernel_stat.h>
  31 #include <linux/delay.h>
  32 #include <linux/init.h>
  33 #include <linux/spinlock.h>
  34 #include <linux/errno.h>
  35 #include <linux/hardirq.h>
  36 #include <linux/cpu.h>
  37 #include <linux/compiler.h>
  38
  39 #include <asm/ptrace.h>
  40 #include <asm/atomic.h>
  41 #include <asm/irq.h>
  42 #include <asm/page.h>
  43 #include <asm/pgtable.h>
  44 #include <asm/sections.h>
  45 #include <asm/io.h>
  46 #include <asm/prom.h>
  47 #include <asm/smp.h>
  48 #include <asm/machdep.h>
  49 #include <asm/pmac_feature.h>
  50 #include <asm/time.h>
  51 #include <asm/mpic.h>
  52 #include <asm/cacheflush.h>
  53 #include <asm/keylargo.h>
  54 #include <asm/pmac_low_i2c.h>
  55
  56 #undef DEBUG
  57
  58 #ifdef DEBUG
  59 #define DBG(fmt...) udbg_printf(fmt)
  60 #else
  61 #define DBG(fmt...)
  62 #endif
  63
  64 extern void __secondary_start_pmac_0(void);
  65
  66 #ifdef CONFIG_PPC32
  67
  68 /* Sync flag for HW tb sync */
  69 static volatile int sec_tb_reset = 0;
  70
  71 /*
  72  * Powersurge (old powermac SMP) support.
  73  */
  74
  75 /* Addresses for powersurge registers */
  76 #define HAMMERHEAD_BASE         0xf8000000
  77 #define HHEAD_CONFIG            0x90
  78 #define HHEAD_SEC_INTR          0xc0
  79
  80 /* register for interrupting the primary processor on the powersurge */
  81 /* N.B. this is actually the ethernet ROM! */
  82 #define PSURGE_PRI_INTR         0xf3019000
  83
  84 /* register for storing the start address for the secondary processor */
  85 /* N.B. this is the PCI config space address register for the 1st bridge */
  86 #define PSURGE_START            0xf2800000
  87
  88 /* Daystar/XLR8 4-CPU card */
  89 #define PSURGE_QUAD_REG_ADDR    0xf8800000
  90
  91 #define PSURGE_QUAD_IRQ_SET     0
  92 #define PSURGE_QUAD_IRQ_CLR     1
  93 #define PSURGE_QUAD_IRQ_PRIMARY 2
  94 #define PSURGE_QUAD_CKSTOP_CTL  3
  95 #define PSURGE_QUAD_PRIMARY_ARB 4
  96 #define PSURGE_QUAD_BOARD_ID    6
  97 #define PSURGE_QUAD_WHICH_CPU   7
  98 #define PSURGE_QUAD_CKSTOP_RDBK 8
  99 #define PSURGE_QUAD_RESET_CTL   11
 100
 101 #define PSURGE_QUAD_OUT(r, v)   (out_8(quad_base + ((r) << 4) + 4, (v)))
 102 #define PSURGE_QUAD_IN(r)       (in_8(quad_base + ((r) << 4) + 4) & 0x0f)
 103 #define PSURGE_QUAD_BIS(r, v)   (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) | (v)))
 104 #define PSURGE_QUAD_BIC(r, v)   (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) & ~(v)))
 105
 106 /* virtual addresses for the above */
 107 static volatile u8 __iomem *hhead_base;
 108 static volatile u8 __iomem *quad_base;
 109 static volatile u32 __iomem *psurge_pri_intr;
 110 static volatile u8 __iomem *psurge_sec_intr;
 111 static volatile u32 __iomem *psurge_start;
 112
 113 /* values for psurge_type */
 114 #define PSURGE_NONE             -1
 115 #define PSURGE_DUAL             0
 116 #define PSURGE_QUAD_OKEE        1
 117 #define PSURGE_QUAD_COTTON      2
 118 #define PSURGE_QUAD_ICEGRASS    3
 119
 120 /* what sort of powersurge board we have */
 121 static int psurge_type = PSURGE_NONE;
 122
 123 /*
 124  * Set and clear IPIs for powersurge.
 125  */
 126 static inline void psurge_set_ipi(int cpu)
 127 {
 128         if (psurge_type == PSURGE_NONE)
 129                 return;
 130         if (cpu == 0)
 131                 in_be32(psurge_pri_intr);
 132         else if (psurge_type == PSURGE_DUAL)
 133                 out_8(psurge_sec_intr, 0);
 134         else
 135                 PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_SET, 1 << cpu);
 136 }
 137
 138 static inline void psurge_clr_ipi(int cpu)
 139 {
 140         if (cpu > 0) {
 141                 switch(psurge_type) {
 142                 case PSURGE_DUAL:
 143                         out_8(psurge_sec_intr, ~0);
 144                 case PSURGE_NONE:
 145                         break;
 146                 default:
 147                         PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, 1 << cpu);
 148                 }
 149         }
 150 }
 151
 152 /*
 153  * On powersurge (old SMP powermac architecture) we don't have
 154  * separate IPIs for separate messages like openpic does.  Instead
 155  * we have a bitmap for each processor, where a 1 bit means that
 156  * the corresponding message is pending for that processor.
 157  * Ideally each cpu's entry would be in a different cache line.
 158  *  -- paulus.
 159  */
 160 static unsigned long psurge_smp_message[NR_CPUS];
 161
 162 void psurge_smp_message_recv(struct pt_regs *regs)
 163 {
 164         int cpu = smp_processor_id();
 165         int msg;
 166
 167         /* clear interrupt */
 168         psurge_clr_ipi(cpu);
 169
 170         if (num_online_cpus() < 2)
 171                 return;
 172
 173         /* make sure there is a message there */
 174         for (msg = 0; msg < 4; msg++)
 175                 if (test_and_clear_bit(msg, &psurge_smp_message[cpu]))
 176                         smp_message_recv(msg, regs);
 177 }
 178
 179 irqreturn_t psurge_primary_intr(int irq, void *d, struct pt_regs *regs)
 180 {
 181         psurge_smp_message_recv(regs);
 182         return IRQ_HANDLED;
 183 }
 184
 185 static void smp_psurge_message_pass(int target, int msg)
 186 {
 187         int i;
 188
 189         if (num_online_cpus() < 2)
 190                 return;
 191
 192         for (i = 0; i < NR_CPUS; i++) {
 193                 if (!cpu_online(i))
 194                         continue;
 195                 if (target == MSG_ALL
 196                     || (target == MSG_ALL_BUT_SELF && i != smp_processor_id())
 197                     || target == i) {
 198                         set_bit(msg, &psurge_smp_message[i]);
 199                         psurge_set_ipi(i);
 200                 }
 201         }
 202 }
 203
 204 /*
 205  * Determine a quad card presence. We read the board ID register, we
 206  * force the data bus to change to something else, and we read it again.
 207  * It it's stable, then the register probably exist (ugh !)
 208  */
 209 static int __init psurge_quad_probe(void)
 210 {
 211         int type;
 212         unsigned int i;
 213
 214         type = PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID);
 215         if (type < PSURGE_QUAD_OKEE || type > PSURGE_QUAD_ICEGRASS
 216             || type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID))
 217                 return PSURGE_DUAL;
 218
 219         /* looks OK, try a slightly more rigorous test */
 220         /* bogus is not necessarily cacheline-aligned,
 221            though I don't suppose that really matters.  -- paulus */
 222         for (i = 0; i < 100; i++) {
 223                 volatile u32 bogus[8];
 224                 bogus[(0+i)%8] = 0x00000000;
 225                 bogus[(1+i)%8] = 0x55555555;
 226                 bogus[(2+i)%8] = 0xFFFFFFFF;
 227                 bogus[(3+i)%8] = 0xAAAAAAAA;
 228                 bogus[(4+i)%8] = 0x33333333;
 229                 bogus[(5+i)%8] = 0xCCCCCCCC;
 230                 bogus[(6+i)%8] = 0xCCCCCCCC;
 231                 bogus[(7+i)%8] = 0x33333333;
 232                 wmb();
 233                 asm volatile("dcbf 0,%0" : : "r" (bogus) : "memory");
 234                 mb();
 235                 if (type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID))
 236                         return PSURGE_DUAL;
 237         }
 238         return type;
 239 }
 240
 241 static void __init psurge_quad_init(void)
 242 {
 243         int procbits;
 244
 245         if (ppc_md.progress) ppc_md.progress("psurge_quad_init", 0x351);
 246         procbits = ~PSURGE_QUAD_IN(PSURGE_QUAD_WHICH_CPU);
 247         if (psurge_type == PSURGE_QUAD_ICEGRASS)
 248                 PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits);
 249         else
 250                 PSURGE_QUAD_BIC(PSURGE_QUAD_CKSTOP_CTL, procbits);
 251         mdelay(33);
 252         out_8(psurge_sec_intr, ~0);
 253         PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, procbits);
 254         PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits);
 255         if (psurge_type != PSURGE_QUAD_ICEGRASS)
 256                 PSURGE_QUAD_BIS(PSURGE_QUAD_CKSTOP_CTL, procbits);
 257         PSURGE_QUAD_BIC(PSURGE_QUAD_PRIMARY_ARB, procbits);
 258         mdelay(33);
 259         PSURGE_QUAD_BIC(PSURGE_QUAD_RESET_CTL, procbits);
 260         mdelay(33);
 261         PSURGE_QUAD_BIS(PSURGE_QUAD_PRIMARY_ARB, procbits);
 262         mdelay(33);
 263 }
 264
 265 static int __init smp_psurge_probe(void)
 266 {
 267         int i, ncpus;
 268
 269         /* We don't do SMP on the PPC601 -- paulus */
 270         if (PVR_VER(mfspr(SPRN_PVR)) == 1)
 271                 return 1;
 272
 273         /*
 274          * The powersurge cpu board can be used in the generation
 275          * of powermacs that have a socket for an upgradeable cpu card,
 276          * including the 7500, 8500, 9500, 9600.
 277          * The device tree doesn't tell you if you have 2 cpus because
 278          * OF doesn't know anything about the 2nd processor.
 279          * Instead we look for magic bits in magic registers,
 280          * in the hammerhead memory controller in the case of the
 281          * dual-cpu powersurge board.  -- paulus.
 282          */
 283         if (find_devices("hammerhead") == NULL)
 284                 return 1;
 285
 286         hhead_base = ioremap(HAMMERHEAD_BASE, 0x800);
 287         quad_base = ioremap(PSURGE_QUAD_REG_ADDR, 1024);
 288         psurge_sec_intr = hhead_base + HHEAD_SEC_INTR;
 289
 290         psurge_type = psurge_quad_probe();
 291         if (psurge_type != PSURGE_DUAL) {
 292                 psurge_quad_init();
 293                 /* All released cards using this HW design have 4 CPUs */
 294                 ncpus = 4;
 295         } else {
 296                 iounmap(quad_base);
 297                 if ((in_8(hhead_base + HHEAD_CONFIG) & 0x02) == 0) {
 298                         /* not a dual-cpu card */
 299                         iounmap(hhead_base);
 300                         psurge_type = PSURGE_NONE;
 301                         return 1;
 302                 }
 303                 ncpus = 2;
 304         }
 305
 306         psurge_start = ioremap(PSURGE_START, 4);
 307         psurge_pri_intr = ioremap(PSURGE_PRI_INTR, 4);
 308
 309         /*
 310          * This is necessary because OF doesn't know about the
 311          * secondary cpu(s), and thus there aren't nodes in the
 312          * device tree for them, and smp_setup_cpu_maps hasn't
 313          * set their bits in cpu_possible_map and cpu_present_map.
 314          */
 315         if (ncpus > NR_CPUS)
 316                 ncpus = NR_CPUS;
 317         for (i = 1; i < ncpus ; ++i) {
 318                 cpu_set(i, cpu_present_map);
 319                 cpu_set(i, cpu_possible_map);
 320                 set_hard_smp_processor_id(i, i);
 321         }
 322
 323         if (ppc_md.progress) ppc_md.progress("smp_psurge_probe - done", 0x352);
 324
 325         return ncpus;
 326 }
 327
 328 static void __init smp_psurge_kick_cpu(int nr)
 329 {
 330         unsigned long start = __pa(__secondary_start_pmac_0) + nr * 8;
 331         unsigned long a;
 332
 333         /* may need to flush here if secondary bats aren't setup */
 334         for (a = KERNELBASE; a < KERNELBASE + 0x800000; a += 32)
 335                 asm volatile("dcbf 0,%0" : : "r" (a) : "memory");
 336         asm volatile("sync");
 337
 338         if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu", 0x353);
 339
 340         out_be32(psurge_start, start);
 341         mb();
 342
 343         psurge_set_ipi(nr);
 344         udelay(10);
 345         psurge_clr_ipi(nr);
 346
 347         if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354);
 348 }
 349
 350 /*
 351  * With the dual-cpu powersurge board, the decrementers and timebases
 352  * of both cpus are frozen after the secondary cpu is started up,
 353  * until we give the secondary cpu another interrupt.  This routine
 354  * uses this to get the timebases synchronized.
 355  *  -- paulus.
 356  */
 357 static void __init psurge_dual_sync_tb(int cpu_nr)
 358 {
 359         int t;
 360
 361         set_dec(tb_ticks_per_jiffy);
 362         /* XXX fixme */
 363         set_tb(0, 0);
 364         last_jiffy_stamp(cpu_nr) = 0;
 365
 366         if (cpu_nr > 0) {
 367                 mb();
 368                 sec_tb_reset = 1;
 369                 return;
 370         }
 371
 372         /* wait for the secondary to have reset its TB before proceeding */
 373         for (t = 10000000; t > 0 && !sec_tb_reset; --t)
 374                 ;
 375
 376         /* now interrupt the secondary, starting both TBs */
 377         psurge_set_ipi(1);
 378 }
 379
 380 static struct irqaction psurge_irqaction = {
 381         .handler = psurge_primary_intr,
 382         .flags = SA_INTERRUPT,
 383         .mask = CPU_MASK_NONE,
 384         .name = "primary IPI",
 385 };
 386
 387 static void __init smp_psurge_setup_cpu(int cpu_nr)
 388 {
 389
 390         if (cpu_nr == 0) {
 391                 /* If we failed to start the second CPU, we should still
 392                  * send it an IPI to start the timebase & DEC or we might
 393                  * have them stuck.
 394                  */
 395                 if (num_online_cpus() < 2) {
 396                         if (psurge_type == PSURGE_DUAL)
 397                                 psurge_set_ipi(1);
 398                         return;
 399                 }
 400                 /* reset the entry point so if we get another intr we won't
 401                  * try to startup again */
 402                 out_be32(psurge_start, 0x100);
 403                 if (setup_irq(30, &psurge_irqaction))
 404                         printk(KERN_ERR "Couldn't get primary IPI interrupt");
 405         }
 406
 407         if (psurge_type == PSURGE_DUAL)
 408                 psurge_dual_sync_tb(cpu_nr);
 409 }
 410
 411 void __init smp_psurge_take_timebase(void)
 412 {
 413         /* Dummy implementation */
 414 }
 415
 416 void __init smp_psurge_give_timebase(void)
 417 {
 418         /* Dummy implementation */
 419 }
 420
 421 /* PowerSurge-style Macs */
 422 struct smp_ops_t psurge_smp_ops = {
 423         .message_pass   = smp_psurge_message_pass,
 424         .probe          = smp_psurge_probe,
 425         .kick_cpu       = smp_psurge_kick_cpu,
 426         .setup_cpu      = smp_psurge_setup_cpu,
 427         .give_timebase  = smp_psurge_give_timebase,
 428         .take_timebase  = smp_psurge_take_timebase,
 429 };
 430 #endif /* CONFIG_PPC32 - actually powersurge support */
 431
 432 #ifdef CONFIG_PPC64
 433 /*
 434  * G5s enable/disable the timebase via an i2c-connected clock chip.
 435  */
 436 static struct device_node *pmac_tb_clock_chip_host;
 437 static u8 pmac_tb_pulsar_addr;
 438 static void (*pmac_tb_freeze)(int freeze);
 439 static DEFINE_SPINLOCK(timebase_lock);
 440 static unsigned long timebase;
 441
 442 static void smp_core99_cypress_tb_freeze(int freeze)
 443 {
 444         u8 data;
 445         int rc;
 446
 447         /* Strangely, the device-tree says address is 0xd2, but darwin
 448          * accesses 0xd0 ...
 449          */
 450         pmac_low_i2c_setmode(pmac_tb_clock_chip_host, pmac_low_i2c_mode_combined);
 451         rc = pmac_low_i2c_xfer(pmac_tb_clock_chip_host,
 452                                0xd0 | pmac_low_i2c_read,
 453                                0x81, &data, 1);
 454         if (rc != 0)
 455                 goto bail;
 456
 457         data = (data & 0xf3) | (freeze ? 0x00 : 0x0c);
 458
 459         pmac_low_i2c_setmode(pmac_tb_clock_chip_host, pmac_low_i2c_mode_stdsub);
 460         rc = pmac_low_i2c_xfer(pmac_tb_clock_chip_host,
 461                                0xd0 | pmac_low_i2c_write,
 462                                0x81, &data, 1);
 463
 464  bail:
 465         if (rc != 0) {
 466                 printk("Cypress Timebase %s rc: %d\n",
 467                        freeze ? "freeze" : "unfreeze", rc);
 468                 panic("Timebase freeze failed !\n");
 469         }
 470 }
 471
 472
 473 static void smp_core99_pulsar_tb_freeze(int freeze)
 474 {
 475         u8 data;
 476         int rc;
 477
 478         pmac_low_i2c_setmode(pmac_tb_clock_chip_host, pmac_low_i2c_mode_combined);
 479         rc = pmac_low_i2c_xfer(pmac_tb_clock_chip_host,
 480                                pmac_tb_pulsar_addr | pmac_low_i2c_read,
 481                                0x2e, &data, 1);
 482         if (rc != 0)
 483                 goto bail;
 484
 485         data = (data & 0x88) | (freeze ? 0x11 : 0x22);
 486
 487         pmac_low_i2c_setmode(pmac_tb_clock_chip_host, pmac_low_i2c_mode_stdsub);
 488         rc = pmac_low_i2c_xfer(pmac_tb_clock_chip_host,
 489                                pmac_tb_pulsar_addr | pmac_low_i2c_write,
 490                                0x2e, &data, 1);
 491  bail:
 492         if (rc != 0) {
 493                 printk(KERN_ERR "Pulsar Timebase %s rc: %d\n",
 494                        freeze ? "freeze" : "unfreeze", rc);
 495                 panic("Timebase freeze failed !\n");
 496         }
 497 }
 498
 499
 500 static void smp_core99_give_timebase(void)
 501 {
 502         /* Open i2c bus for synchronous access */
 503         if (pmac_low_i2c_open(pmac_tb_clock_chip_host, 0))
 504                 panic("Can't open i2c for TB sync !\n");
 505
 506         spin_lock(&timebase_lock);
 507         (*pmac_tb_freeze)(1);
 508         mb();
 509         timebase = get_tb();
 510         spin_unlock(&timebase_lock);
 511
 512         while (timebase)
 513                 barrier();
 514
 515         spin_lock(&timebase_lock);
 516         (*pmac_tb_freeze)(0);
 517         spin_unlock(&timebase_lock);
 518
 519         /* Close i2c bus */
 520         pmac_low_i2c_close(pmac_tb_clock_chip_host);
 521 }
 522
 523
 524 static void __devinit smp_core99_take_timebase(void)
 525 {
 526         while (!timebase)
 527                 barrier();
 528         spin_lock(&timebase_lock);
 529         set_tb(timebase >> 32, timebase & 0xffffffff);
 530         timebase = 0;
 531         spin_unlock(&timebase_lock);
 532 }
 533
 534 static void __init smp_core99_setup(int ncpus)
 535 {
 536         struct device_node *cc = NULL;
 537         struct device_node *p;
 538         u32 *reg;
 539         int ok;
 540
 541         /* HW sync only on these platforms */
 542         if (!machine_is_compatible("PowerMac7,2") &&
 543             !machine_is_compatible("PowerMac7,3") &&
 544             !machine_is_compatible("RackMac3,1"))
 545                 return;
 546
 547         /* Look for the clock chip */
 548         while ((cc = of_find_node_by_name(cc, "i2c-hwclock")) != NULL) {
 549                 p = of_get_parent(cc);
 550                 ok = p && device_is_compatible(p, "uni-n-i2c");
 551                 of_node_put(p);
 552                 if (!ok)
 553                         continue;
 554
 555                 reg = (u32 *)get_property(cc, "reg", NULL);
 556                 if (reg == NULL)
 557                         continue;
 558
 559                 switch (*reg) {
 560                 case 0xd2:
 561                         if (device_is_compatible(cc, "pulsar-legacy-slewing")) {
 562                                 pmac_tb_freeze = smp_core99_pulsar_tb_freeze;
 563                                 pmac_tb_pulsar_addr = 0xd2;
 564                                 printk(KERN_INFO "Timebase clock is Pulsar chip\n");
 565                         } else if (device_is_compatible(cc, "cy28508")) {
 566                                 pmac_tb_freeze = smp_core99_cypress_tb_freeze;
 567                                 printk(KERN_INFO "Timebase clock is Cypress chip\n");
 568                         }
 569                         break;
 570                 case 0xd4:
 571                         pmac_tb_freeze = smp_core99_pulsar_tb_freeze;
 572                         pmac_tb_pulsar_addr = 0xd4;
 573                         printk(KERN_INFO "Timebase clock is Pulsar chip\n");
 574                         break;
 575                 }
 576                 if (pmac_tb_freeze != NULL) {
 577                         pmac_tb_clock_chip_host = of_get_parent(cc);
 578                         of_node_put(cc);
 579                         break;
 580                 }
 581         }
 582         if (pmac_tb_freeze == NULL) {
 583                 smp_ops->give_timebase = smp_generic_give_timebase;
 584                 smp_ops->take_timebase = smp_generic_take_timebase;
 585         }
 586 }
 587
 588 /* nothing to do here, caches are already set up by service processor */
 589 static inline void __devinit core99_init_caches(int cpu)
 590 {
 591 }
 592
 593 #else /* CONFIG_PPC64 */
 594
 595 /*
 596  * SMP G4 powermacs use a GPIO to enable/disable the timebase.
 597  */
 598
 599 static unsigned int core99_tb_gpio;     /* Timebase freeze GPIO */
 600
 601 static unsigned int pri_tb_hi, pri_tb_lo;
 602 static unsigned int pri_tb_stamp;
 603
 604 /* not __init, called in sleep/wakeup code */
 605 void smp_core99_give_timebase(void)
 606 {
 607         unsigned long flags;
 608         unsigned int t;
 609
 610         /* wait for the secondary to be in take_timebase */
 611         for (t = 100000; t > 0 && !sec_tb_reset; --t)
 612                 udelay(10);
 613         if (!sec_tb_reset) {
 614                 printk(KERN_WARNING "Timeout waiting sync on second CPU\n");
 615                 return;
 616         }
 617
 618         /* freeze the timebase and read it */
 619         /* disable interrupts so the timebase is disabled for the
 620            shortest possible time */
 621         local_irq_save(flags);
 622         pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 4);
 623         pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, core99_tb_gpio, 0);
 624         mb();
 625         pri_tb_hi = get_tbu();
 626         pri_tb_lo = get_tbl();
 627         pri_tb_stamp = last_jiffy_stamp(smp_processor_id());
 628         mb();
 629
 630         /* tell the secondary we're ready */
 631         sec_tb_reset = 2;
 632         mb();
 633
 634         /* wait for the secondary to have taken it */
 635         /* note: can't use udelay here, since it needs the timebase running */
 636         for (t = 10000000; t > 0 && sec_tb_reset; --t)
 637                 barrier();
 638         if (sec_tb_reset)
 639                 /* XXX BUG_ON here? */
 640                 printk(KERN_WARNING "Timeout waiting sync(2) on second CPU\n");
 641
 642         /* Now, restart the timebase by leaving the GPIO to an open collector */
 643         pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 0);
 644         pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, core99_tb_gpio, 0);
 645         local_irq_restore(flags);
 646 }
 647
 648 /* not __init, called in sleep/wakeup code */
 649 void smp_core99_take_timebase(void)
 650 {
 651         unsigned long flags;
 652
 653         /* tell the primary we're here */
 654         sec_tb_reset = 1;
 655         mb();
 656
 657         /* wait for the primary to set pri_tb_hi/lo */
 658         while (sec_tb_reset < 2)
 659                 mb();
 660
 661         /* set our stuff the same as the primary */
 662         local_irq_save(flags);
 663         set_dec(1);
 664         set_tb(pri_tb_hi, pri_tb_lo);
 665         last_jiffy_stamp(smp_processor_id()) = pri_tb_stamp;
 666         mb();
 667
 668         /* tell the primary we're done */
 669         sec_tb_reset = 0;
 670         mb();
 671         local_irq_restore(flags);
 672 }
 673
 674 /* L2 and L3 cache settings to pass from CPU0 to CPU1 on G4 cpus */
 675 volatile static long int core99_l2_cache;
 676 volatile static long int core99_l3_cache;
 677
 678 static void __devinit core99_init_caches(int cpu)
 679 {
 680         if (!cpu_has_feature(CPU_FTR_L2CR))
 681                 return;
 682
 683         if (cpu == 0) {
 684                 core99_l2_cache = _get_L2CR();
 685                 printk("CPU0: L2CR is %lx\n", core99_l2_cache);
 686         } else {
 687                 printk("CPU%d: L2CR was %lx\n", cpu, _get_L2CR());
 688                 _set_L2CR(0);
 689                 _set_L2CR(core99_l2_cache);
 690                 printk("CPU%d: L2CR set to %lx\n", cpu, core99_l2_cache);
 691         }
 692
 693         if (!cpu_has_feature(CPU_FTR_L3CR))
 694                 return;
 695
 696         if (cpu == 0){
 697                 core99_l3_cache = _get_L3CR();
 698                 printk("CPU0: L3CR is %lx\n", core99_l3_cache);
 699         } else {
 700                 printk("CPU%d: L3CR was %lx\n", cpu, _get_L3CR());
 701                 _set_L3CR(0);
 702                 _set_L3CR(core99_l3_cache);
 703                 printk("CPU%d: L3CR set to %lx\n", cpu, core99_l3_cache);
 704         }
 705 }
 706
 707 static void __init smp_core99_setup(int ncpus)
 708 {
 709         struct device_node *cpu;
 710         u32 *tbprop = NULL;
 711         int i;
 712
 713         core99_tb_gpio = KL_GPIO_TB_ENABLE;     /* default value */
 714         cpu = of_find_node_by_type(NULL, "cpu");
 715         if (cpu != NULL) {
 716                 tbprop = (u32 *)get_property(cpu, "timebase-enable", NULL);
 717                 if (tbprop)
 718                         core99_tb_gpio = *tbprop;
 719                 of_node_put(cpu);
 720         }
 721
 722         /* XXX should get this from reg properties */
 723         for (i = 1; i < ncpus; ++i)
 724                 smp_hw_index[i] = i;
 725         powersave_nap = 0;
 726 }
 727 #endif
 728
 729 static int __init smp_core99_probe(void)
 730 {
 731         struct device_node *cpus;
 732         int ncpus = 0;
 733
 734         if (ppc_md.progress) ppc_md.progress("smp_core99_probe", 0x345);
 735
 736         /* Count CPUs in the device-tree */
 737         for (cpus = NULL; (cpus = of_find_node_by_type(cpus, "cpu")) != NULL;)
 738                 ++ncpus;
 739
 740         printk(KERN_INFO "PowerMac SMP probe found %d cpus\n", ncpus);
 741
 742         /* Nothing more to do if less than 2 of them */
 743         if (ncpus <= 1)
 744                 return 1;
 745
 746         smp_core99_setup(ncpus);
 747         mpic_request_ipis();
 748         core99_init_caches(0);
 749
 750         return ncpus;
 751 }
 752
 753 static void __devinit smp_core99_kick_cpu(int nr)
 754 {
 755         unsigned int save_vector;
 756         unsigned long new_vector;
 757         unsigned long flags;
 758         volatile unsigned int *vector
 759                  = ((volatile unsigned int *)(KERNELBASE+0x100));
 760
 761         if (nr < 0 || nr > 3)
 762                 return;
 763         if (ppc_md.progress) ppc_md.progress("smp_core99_kick_cpu", 0x346);
 764
 765         local_irq_save(flags);
 766         local_irq_disable();
 767
 768         /* Save reset vector */
 769         save_vector = *vector;
 770
 771         /* Setup fake reset vector that does
 772          *   b __secondary_start_pmac_0 + nr*8 - KERNELBASE
 773          */
 774         new_vector = (unsigned long) __secondary_start_pmac_0 + nr * 8;
 775         *vector = 0x48000002 + new_vector - KERNELBASE;
 776
 777         /* flush data cache and inval instruction cache */
 778         flush_icache_range((unsigned long) vector, (unsigned long) vector + 4);
 779
 780         /* Put some life in our friend */
 781         pmac_call_feature(PMAC_FTR_RESET_CPU, NULL, nr, 0);
 782
 783         /* FIXME: We wait a bit for the CPU to take the exception, I should
 784          * instead wait for the entry code to set something for me. Well,
 785          * ideally, all that crap will be done in prom.c and the CPU left
 786          * in a RAM-based wait loop like CHRP.
 787          */
 788         mdelay(1);
 789
 790         /* Restore our exception vector */
 791         *vector = save_vector;
 792         flush_icache_range((unsigned long) vector, (unsigned long) vector + 4);
 793
 794         local_irq_restore(flags);
 795         if (ppc_md.progress) ppc_md.progress("smp_core99_kick_cpu done", 0x347);
 796 }
 797
 798 static void __devinit smp_core99_setup_cpu(int cpu_nr)
 799 {
 800         /* Setup L2/L3 */
 801         if (cpu_nr != 0)
 802                 core99_init_caches(cpu_nr);
 803
 804         /* Setup openpic */
 805         mpic_setup_this_cpu();
 806
 807         if (cpu_nr == 0) {
 808 #ifdef CONFIG_POWER4
 809                 extern void g5_phy_disable_cpu1(void);
 810
 811                 /* If we didn't start the second CPU, we must take
 812                  * it off the bus
 813                  */
 814                 if (machine_is_compatible("MacRISC4") &&
 815                     num_online_cpus() < 2)
 816                         g5_phy_disable_cpu1();
 817 #endif /* CONFIG_POWER4 */
 818                 if (ppc_md.progress) ppc_md.progress("core99_setup_cpu 0 done", 0x349);
 819         }
 820 }
 821
 822
 823 #if defined(CONFIG_HOTPLUG_CPU) && defined(CONFIG_PPC32)
 824
 825 int smp_core99_cpu_disable(void)
 826 {
 827         cpu_clear(smp_processor_id(), cpu_online_map);
 828
 829         /* XXX reset cpu affinity here */
 830         mpic_cpu_set_priority(0xf);
 831         asm volatile("mtdec %0" : : "r" (0x7fffffff));
 832         mb();
 833         udelay(20);
 834         asm volatile("mtdec %0" : : "r" (0x7fffffff));
 835         return 0;
 836 }
 837
 838 extern void low_cpu_die(void) __attribute__((noreturn)); /* in sleep.S */
 839 static int cpu_dead[NR_CPUS];
 840
 841 void cpu_die(void)
 842 {
 843         local_irq_disable();
 844         cpu_dead[smp_processor_id()] = 1;
 845         mb();
 846         low_cpu_die();
 847 }
 848
 849 void smp_core99_cpu_die(unsigned int cpu)
 850 {
 851         int timeout;
 852
 853         timeout = 1000;
 854         while (!cpu_dead[cpu]) {
 855                 if (--timeout == 0) {
 856                         printk("CPU %u refused to die!\n", cpu);
 857                         break;
 858                 }
 859                 msleep(1);
 860         }
 861         cpu_dead[cpu] = 0;
 862 }
 863
 864 #endif
 865
 866 /* Core99 Macs (dual G4s and G5s) */
 867 struct smp_ops_t core99_smp_ops = {
 868         .message_pass   = smp_mpic_message_pass,
 869         .probe          = smp_core99_probe,
 870         .kick_cpu       = smp_core99_kick_cpu,
 871         .setup_cpu      = smp_core99_setup_cpu,
 872         .give_timebase  = smp_core99_give_timebase,
 873         .take_timebase  = smp_core99_take_timebase,
 874 #if defined(CONFIG_HOTPLUG_CPU) && defined(CONFIG_PPC32)
 875         .cpu_disable    = smp_core99_cpu_disable,
 876         .cpu_die        = smp_core99_cpu_die,
 877 #endif
 878 };