arch/blackfin/mach-bf537/boards/stamp.c

   1 /*
   2  * Copyright 2004-2009 Analog Devices Inc.
   3  *                2005 National ICT Australia (NICTA)
   4  *                      Aidan Williams <aidan@nicta.com.au>
   5  *
   6  * Licensed under the GPL-2 or later.
   7  */
   8
   9 #include <linux/device.h>
  10 #include <linux/kernel.h>
  11 #include <linux/platform_device.h>
  12 #include <linux/io.h>
  13 #include <linux/mtd/mtd.h>
  14 #include <linux/mtd/nand.h>
  15 #include <linux/mtd/partitions.h>
  16 #include <linux/mtd/plat-ram.h>
  17 #include <linux/mtd/physmap.h>
  18 #include <linux/spi/spi.h>
  19 #include <linux/spi/flash.h>
  20 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
  21 #include <linux/usb/isp1362.h>
  22 #endif
  23 #include <linux/i2c.h>
  24 #include <linux/i2c/adp5588.h>
  25 #include <linux/etherdevice.h>
  26 #include <linux/ata_platform.h>
  27 #include <linux/irq.h>
  28 #include <linux/interrupt.h>
  29 #include <linux/usb/sl811.h>
  30 #include <linux/spi/mmc_spi.h>
  31 #include <linux/leds.h>
  32 #include <linux/input.h>
  33 #include <asm/dma.h>
  34 #include <asm/bfin5xx_spi.h>
  35 #include <asm/reboot.h>
  36 #include <asm/portmux.h>
  37 #include <asm/dpmc.h>
  38
  39 /*
  40  * Name the Board for the /proc/cpuinfo
  41  */
  42 const char bfin_board_name[] = "ADI BF537-STAMP";
  43
  44 /*
  45  *  Driver needs to know address, irq and flag pin.
  46  */
  47
  48 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
  49 #include <linux/usb/isp1760.h>
  50 static struct resource bfin_isp1760_resources[] = {
  51         [0] = {
  52                 .start  = 0x203C0000,
  53                 .end    = 0x203C0000 + 0x000fffff,
  54                 .flags  = IORESOURCE_MEM,
  55         },
  56         [1] = {
  57                 .start  = IRQ_PF7,
  58                 .end    = IRQ_PF7,
  59                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
  60         },
  61 };
  62
  63 static struct isp1760_platform_data isp1760_priv = {
  64         .is_isp1761 = 0,
  65         .bus_width_16 = 1,
  66         .port1_otg = 0,
  67         .analog_oc = 0,
  68         .dack_polarity_high = 0,
  69         .dreq_polarity_high = 0,
  70 };
  71
  72 static struct platform_device bfin_isp1760_device = {
  73         .name           = "isp1760",
  74         .id             = 0,
  75         .dev = {
  76                 .platform_data = &isp1760_priv,
  77         },
  78         .num_resources  = ARRAY_SIZE(bfin_isp1760_resources),
  79         .resource       = bfin_isp1760_resources,
  80 };
  81 #endif
  82
  83 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
  84 #include <linux/gpio_keys.h>
  85
  86 static struct gpio_keys_button bfin_gpio_keys_table[] = {
  87         {BTN_0, GPIO_PF2, 1, "gpio-keys: BTN0"},
  88         {BTN_1, GPIO_PF3, 1, "gpio-keys: BTN1"},
  89         {BTN_2, GPIO_PF4, 1, "gpio-keys: BTN2"},
  90         {BTN_3, GPIO_PF5, 1, "gpio-keys: BTN3"},
  91 };
  92
  93 static struct gpio_keys_platform_data bfin_gpio_keys_data = {
  94         .buttons        = bfin_gpio_keys_table,
  95         .nbuttons       = ARRAY_SIZE(bfin_gpio_keys_table),
  96 };
  97
  98 static struct platform_device bfin_device_gpiokeys = {
  99         .name      = "gpio-keys",
 100         .dev = {
 101                 .platform_data = &bfin_gpio_keys_data,
 102         },
 103 };
 104 #endif
 105
 106 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
 107 static struct resource bfin_pcmcia_cf_resources[] = {
 108         {
 109                 .start = 0x20310000, /* IO PORT */
 110                 .end = 0x20312000,
 111                 .flags = IORESOURCE_MEM,
 112         }, {
 113                 .start = 0x20311000, /* Attribute Memory */
 114                 .end = 0x20311FFF,
 115                 .flags = IORESOURCE_MEM,
 116         }, {
 117                 .start = IRQ_PF4,
 118                 .end = IRQ_PF4,
 119                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 120         }, {
 121                 .start = 6, /* Card Detect PF6 */
 122                 .end = 6,
 123                 .flags = IORESOURCE_IRQ,
 124         },
 125 };
 126
 127 static struct platform_device bfin_pcmcia_cf_device = {
 128         .name = "bfin_cf_pcmcia",
 129         .id = -1,
 130         .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
 131         .resource = bfin_pcmcia_cf_resources,
 132 };
 133 #endif
 134
 135 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 136 static struct platform_device rtc_device = {
 137         .name = "rtc-bfin",
 138         .id   = -1,
 139 };
 140 #endif
 141
 142 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 143 #include <linux/smc91x.h>
 144
 145 static struct smc91x_platdata smc91x_info = {
 146         .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 147         .leda = RPC_LED_100_10,
 148         .ledb = RPC_LED_TX_RX,
 149 };
 150
 151 static struct resource smc91x_resources[] = {
 152         {
 153                 .name = "smc91x-regs",
 154                 .start = 0x20300300,
 155                 .end = 0x20300300 + 16,
 156                 .flags = IORESOURCE_MEM,
 157         }, {
 158
 159                 .start = IRQ_PF7,
 160                 .end = IRQ_PF7,
 161                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 162         },
 163 };
 164 static struct platform_device smc91x_device = {
 165         .name = "smc91x",
 166         .id = 0,
 167         .num_resources = ARRAY_SIZE(smc91x_resources),
 168         .resource = smc91x_resources,
 169         .dev    = {
 170                 .platform_data  = &smc91x_info,
 171         },
 172 };
 173 #endif
 174
 175 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
 176 static struct resource dm9000_resources[] = {
 177         [0] = {
 178                 .start  = 0x203FB800,
 179                 .end    = 0x203FB800 + 1,
 180                 .flags  = IORESOURCE_MEM,
 181         },
 182         [1] = {
 183                 .start  = 0x203FB804,
 184                 .end    = 0x203FB804 + 1,
 185                 .flags  = IORESOURCE_MEM,
 186         },
 187         [2] = {
 188                 .start  = IRQ_PF9,
 189                 .end    = IRQ_PF9,
 190                 .flags  = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
 191         },
 192 };
 193
 194 static struct platform_device dm9000_device = {
 195         .name           = "dm9000",
 196         .id             = -1,
 197         .num_resources  = ARRAY_SIZE(dm9000_resources),
 198         .resource       = dm9000_resources,
 199 };
 200 #endif
 201
 202 #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
 203 static struct resource sl811_hcd_resources[] = {
 204         {
 205                 .start = 0x20340000,
 206                 .end = 0x20340000,
 207                 .flags = IORESOURCE_MEM,
 208         }, {
 209                 .start = 0x20340004,
 210                 .end = 0x20340004,
 211                 .flags = IORESOURCE_MEM,
 212         }, {
 213                 .start = IRQ_PF4,
 214                 .end = IRQ_PF4,
 215                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 216         },
 217 };
 218
 219 #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
 220 void sl811_port_power(struct device *dev, int is_on)
 221 {
 222         gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
 223         gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
 224 }
 225 #endif
 226
 227 static struct sl811_platform_data sl811_priv = {
 228         .potpg = 10,
 229         .power = 250,       /* == 500mA */
 230 #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
 231         .port_power = &sl811_port_power,
 232 #endif
 233 };
 234
 235 static struct platform_device sl811_hcd_device = {
 236         .name = "sl811-hcd",
 237         .id = 0,
 238         .dev = {
 239                 .platform_data = &sl811_priv,
 240         },
 241         .num_resources = ARRAY_SIZE(sl811_hcd_resources),
 242         .resource = sl811_hcd_resources,
 243 };
 244 #endif
 245
 246 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 247 static struct resource isp1362_hcd_resources[] = {
 248         {
 249                 .start = 0x20360000,
 250                 .end = 0x20360000,
 251                 .flags = IORESOURCE_MEM,
 252         }, {
 253                 .start = 0x20360004,
 254                 .end = 0x20360004,
 255                 .flags = IORESOURCE_MEM,
 256         }, {
 257                 .start = IRQ_PF3,
 258                 .end = IRQ_PF3,
 259                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 260         },
 261 };
 262
 263 static struct isp1362_platform_data isp1362_priv = {
 264         .sel15Kres = 1,
 265         .clknotstop = 0,
 266         .oc_enable = 0,
 267         .int_act_high = 0,
 268         .int_edge_triggered = 0,
 269         .remote_wakeup_connected = 0,
 270         .no_power_switching = 1,
 271         .power_switching_mode = 0,
 272 };
 273
 274 static struct platform_device isp1362_hcd_device = {
 275         .name = "isp1362-hcd",
 276         .id = 0,
 277         .dev = {
 278                 .platform_data = &isp1362_priv,
 279         },
 280         .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
 281         .resource = isp1362_hcd_resources,
 282 };
 283 #endif
 284
 285 #if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
 286 unsigned short bfin_can_peripherals[] = {
 287         P_CAN0_RX, P_CAN0_TX, 0
 288 };
 289
 290 static struct resource bfin_can_resources[] = {
 291         {
 292                 .start = 0xFFC02A00,
 293                 .end = 0xFFC02FFF,
 294                 .flags = IORESOURCE_MEM,
 295         },
 296         {
 297                 .start = IRQ_CAN_RX,
 298                 .end = IRQ_CAN_RX,
 299                 .flags = IORESOURCE_IRQ,
 300         },
 301         {
 302                 .start = IRQ_CAN_TX,
 303                 .end = IRQ_CAN_TX,
 304                 .flags = IORESOURCE_IRQ,
 305         },
 306         {
 307                 .start = IRQ_CAN_ERROR,
 308                 .end = IRQ_CAN_ERROR,
 309                 .flags = IORESOURCE_IRQ,
 310         },
 311 };
 312
 313 static struct platform_device bfin_can_device = {
 314         .name = "bfin_can",
 315         .num_resources = ARRAY_SIZE(bfin_can_resources),
 316         .resource = bfin_can_resources,
 317         .dev = {
 318                 .platform_data = &bfin_can_peripherals, /* Passed to driver */
 319         },
 320 };
 321 #endif
 322
 323 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 324 static struct platform_device bfin_mii_bus = {
 325         .name = "bfin_mii_bus",
 326 };
 327
 328 static struct platform_device bfin_mac_device = {
 329         .name = "bfin_mac",
 330         .dev.platform_data = &bfin_mii_bus,
 331 };
 332 #endif
 333
 334 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 335 static struct resource net2272_bfin_resources[] = {
 336         {
 337                 .start = 0x20300000,
 338                 .end = 0x20300000 + 0x100,
 339                 .flags = IORESOURCE_MEM,
 340         }, {
 341                 .start = IRQ_PF7,
 342                 .end = IRQ_PF7,
 343                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 344         },
 345 };
 346
 347 static struct platform_device net2272_bfin_device = {
 348         .name = "net2272",
 349         .id = -1,
 350         .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 351         .resource = net2272_bfin_resources,
 352 };
 353 #endif
 354
 355 #if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
 356 #ifdef CONFIG_MTD_PARTITIONS
 357 const char *part_probes[] = { "cmdlinepart", "RedBoot", NULL };
 358
 359 static struct mtd_partition bfin_plat_nand_partitions[] = {
 360         {
 361                 .name   = "linux kernel(nand)",
 362                 .size   = 0x400000,
 363                 .offset = 0,
 364         }, {
 365                 .name   = "file system(nand)",
 366                 .size   = MTDPART_SIZ_FULL,
 367                 .offset = MTDPART_OFS_APPEND,
 368         },
 369 };
 370 #endif
 371
 372 #define BFIN_NAND_PLAT_CLE 2
 373 #define BFIN_NAND_PLAT_ALE 1
 374 static void bfin_plat_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
 375 {
 376         struct nand_chip *this = mtd->priv;
 377
 378         if (cmd == NAND_CMD_NONE)
 379                 return;
 380
 381         if (ctrl & NAND_CLE)
 382                 writeb(cmd, this->IO_ADDR_W + (1 << BFIN_NAND_PLAT_CLE));
 383         else
 384                 writeb(cmd, this->IO_ADDR_W + (1 << BFIN_NAND_PLAT_ALE));
 385 }
 386
 387 #define BFIN_NAND_PLAT_READY GPIO_PF3
 388 static int bfin_plat_nand_dev_ready(struct mtd_info *mtd)
 389 {
 390         return gpio_get_value(BFIN_NAND_PLAT_READY);
 391 }
 392
 393 static struct platform_nand_data bfin_plat_nand_data = {
 394         .chip = {
 395                 .chip_delay = 30,
 396 #ifdef CONFIG_MTD_PARTITIONS
 397                 .part_probe_types = part_probes,
 398                 .partitions = bfin_plat_nand_partitions,
 399                 .nr_partitions = ARRAY_SIZE(bfin_plat_nand_partitions),
 400 #endif
 401         },
 402         .ctrl = {
 403                 .cmd_ctrl  = bfin_plat_nand_cmd_ctrl,
 404                 .dev_ready = bfin_plat_nand_dev_ready,
 405         },
 406 };
 407
 408 #define MAX(x, y) (x > y ? x : y)
 409 static struct resource bfin_plat_nand_resources = {
 410         .start = 0x20212000,
 411         .end   = 0x20212000 + (1 << MAX(BFIN_NAND_PLAT_CLE, BFIN_NAND_PLAT_ALE)),
 412         .flags = IORESOURCE_IO,
 413 };
 414
 415 static struct platform_device bfin_async_nand_device = {
 416         .name = "gen_nand",
 417         .id = -1,
 418         .num_resources = 1,
 419         .resource = &bfin_plat_nand_resources,
 420         .dev = {
 421                 .platform_data = &bfin_plat_nand_data,
 422         },
 423 };
 424
 425 static void bfin_plat_nand_init(void)
 426 {
 427         gpio_request(BFIN_NAND_PLAT_READY, "bfin_nand_plat");
 428 }
 429 #else
 430 static void bfin_plat_nand_init(void) {}
 431 #endif
 432
 433 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 434 static struct mtd_partition stamp_partitions[] = {
 435         {
 436                 .name       = "bootloader(nor)",
 437                 .size       = 0x40000,
 438                 .offset     = 0,
 439         }, {
 440                 .name       = "linux kernel(nor)",
 441                 .size       = 0x180000,
 442                 .offset     = MTDPART_OFS_APPEND,
 443         }, {
 444                 .name       = "file system(nor)",
 445                 .size       = 0x400000 - 0x40000 - 0x180000 - 0x10000,
 446                 .offset     = MTDPART_OFS_APPEND,
 447         }, {
 448                 .name       = "MAC Address(nor)",
 449                 .size       = MTDPART_SIZ_FULL,
 450                 .offset     = 0x3F0000,
 451                 .mask_flags = MTD_WRITEABLE,
 452         }
 453 };
 454
 455 static struct physmap_flash_data stamp_flash_data = {
 456         .width      = 2,
 457         .parts      = stamp_partitions,
 458         .nr_parts   = ARRAY_SIZE(stamp_partitions),
 459 #ifdef CONFIG_ROMKERNEL
 460         .probe_type = "map_rom",
 461 #endif
 462 };
 463
 464 static struct resource stamp_flash_resource = {
 465         .start = 0x20000000,
 466         .end   = 0x203fffff,
 467         .flags = IORESOURCE_MEM,
 468 };
 469
 470 static struct platform_device stamp_flash_device = {
 471         .name          = "physmap-flash",
 472         .id            = 0,
 473         .dev = {
 474                 .platform_data = &stamp_flash_data,
 475         },
 476         .num_resources = 1,
 477         .resource      = &stamp_flash_resource,
 478 };
 479 #endif
 480
 481 #if defined(CONFIG_MTD_M25P80) \
 482         || defined(CONFIG_MTD_M25P80_MODULE)
 483 static struct mtd_partition bfin_spi_flash_partitions[] = {
 484         {
 485                 .name = "bootloader(spi)",
 486                 .size = 0x00040000,
 487                 .offset = 0,
 488                 .mask_flags = MTD_CAP_ROM
 489         }, {
 490                 .name = "linux kernel(spi)",
 491                 .size = 0x180000,
 492                 .offset = MTDPART_OFS_APPEND,
 493         }, {
 494                 .name = "file system(spi)",
 495                 .size = MTDPART_SIZ_FULL,
 496                 .offset = MTDPART_OFS_APPEND,
 497         }
 498 };
 499
 500 static struct flash_platform_data bfin_spi_flash_data = {
 501         .name = "m25p80",
 502         .parts = bfin_spi_flash_partitions,
 503         .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
 504         /* .type = "m25p64", */
 505 };
 506
 507 /* SPI flash chip (m25p64) */
 508 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 509         .enable_dma = 0,         /* use dma transfer with this chip*/
 510         .bits_per_word = 8,
 511 };
 512 #endif
 513
 514 #if defined(CONFIG_BFIN_SPI_ADC) \
 515         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 516 /* SPI ADC chip */
 517 static struct bfin5xx_spi_chip spi_adc_chip_info = {
 518         .enable_dma = 1,         /* use dma transfer with this chip*/
 519         .bits_per_word = 16,
 520 };
 521 #endif
 522
 523 #if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
 524         || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
 525 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 526         .enable_dma = 0,
 527         .bits_per_word = 16,
 528 };
 529 #endif
 530
 531 #if defined(CONFIG_SND_BF5XX_SOC_AD193X) \
 532         || defined(CONFIG_SND_BF5XX_SOC_AD193X_MODULE)
 533 static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
 534         .enable_dma = 0,
 535         .bits_per_word = 8,
 536 };
 537 #endif
 538
 539 #if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
 540 #include <linux/input/ad714x.h>
 541 static struct bfin5xx_spi_chip ad7147_spi_chip_info = {
 542         .enable_dma = 0,
 543         .bits_per_word = 16,
 544 };
 545
 546 static struct ad714x_slider_plat ad7147_spi_slider_plat[] = {
 547         {
 548                 .start_stage = 0,
 549                 .end_stage = 7,
 550                 .max_coord = 128,
 551         },
 552 };
 553
 554 static struct ad714x_button_plat ad7147_spi_button_plat[] = {
 555         {
 556                 .keycode = BTN_FORWARD,
 557                 .l_mask = 0,
 558                 .h_mask = 0x600,
 559         },
 560         {
 561                 .keycode = BTN_LEFT,
 562                 .l_mask = 0,
 563                 .h_mask = 0x500,
 564         },
 565         {
 566                 .keycode = BTN_MIDDLE,
 567                 .l_mask = 0,
 568                 .h_mask = 0x800,
 569         },
 570         {
 571                 .keycode = BTN_RIGHT,
 572                 .l_mask = 0x100,
 573                 .h_mask = 0x400,
 574         },
 575         {
 576                 .keycode = BTN_BACK,
 577                 .l_mask = 0x200,
 578                 .h_mask = 0x400,
 579         },
 580 };
 581 static struct ad714x_platform_data ad7147_spi_platform_data = {
 582         .slider_num = 1,
 583         .button_num = 5,
 584         .slider = ad7147_spi_slider_plat,
 585         .button = ad7147_spi_button_plat,
 586         .stage_cfg_reg =  {
 587                 {0xFBFF, 0x1FFF, 0, 0x2626, 1600, 1600, 1600, 1600},
 588                 {0xEFFF, 0x1FFF, 0, 0x2626, 1650, 1650, 1650, 1650},
 589                 {0xFFFF, 0x1FFE, 0, 0x2626, 1650, 1650, 1650, 1650},
 590                 {0xFFFF, 0x1FFB, 0, 0x2626, 1650, 1650, 1650, 1650},
 591                 {0xFFFF, 0x1FEF, 0, 0x2626, 1650, 1650, 1650, 1650},
 592                 {0xFFFF, 0x1FBF, 0, 0x2626, 1650, 1650, 1650, 1650},
 593                 {0xFFFF, 0x1EFF, 0, 0x2626, 1650, 1650, 1650, 1650},
 594                 {0xFFFF, 0x1BFF, 0, 0x2626, 1600, 1600, 1600, 1600},
 595                 {0xFF7B, 0x3FFF, 0x506,  0x2626, 1100, 1100, 1150, 1150},
 596                 {0xFDFE, 0x3FFF, 0x606,  0x2626, 1100, 1100, 1150, 1150},
 597                 {0xFEBA, 0x1FFF, 0x1400, 0x2626, 1200, 1200, 1300, 1300},
 598                 {0xFFEF, 0x1FFF, 0x0,    0x2626, 1100, 1100, 1150, 1150},
 599         },
 600         .sys_cfg_reg = {0x2B2, 0x0, 0x3233, 0x819, 0x832, 0xCFF, 0xCFF, 0x0},
 601 };
 602 #endif
 603
 604 #if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
 605 #include <linux/input/ad714x.h>
 606 static struct ad714x_button_plat ad7142_i2c_button_plat[] = {
 607         {
 608                 .keycode = BTN_1,
 609                 .l_mask = 0,
 610                 .h_mask = 0x1,
 611         },
 612         {
 613                 .keycode = BTN_2,
 614                 .l_mask = 0,
 615                 .h_mask = 0x2,
 616         },
 617         {
 618                 .keycode = BTN_3,
 619                 .l_mask = 0,
 620                 .h_mask = 0x4,
 621         },
 622         {
 623                 .keycode = BTN_4,
 624                 .l_mask = 0x0,
 625                 .h_mask = 0x8,
 626         },
 627 };
 628 static struct ad714x_platform_data ad7142_i2c_platform_data = {
 629         .button_num = 4,
 630         .button = ad7142_i2c_button_plat,
 631         .stage_cfg_reg =  {
 632                 /* fixme: figure out right setting for all comoponent according
 633                  * to hardware feature of EVAL-AD7142EB board */
 634                 {0xE7FF, 0x3FFF, 0x0005, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 635                 {0xFDBF, 0x3FFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 636                 {0xFFFF, 0x2DFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 637                 {0xFFFF, 0x37BF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 638                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 639                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 640                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 641                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 642                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 643                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 644                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 645                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 646         },
 647         .sys_cfg_reg = {0x0B2, 0x0, 0x690, 0x664, 0x290F, 0xF, 0xF, 0x0},
 648 };
 649 #endif
 650
 651 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 652 #define MMC_SPI_CARD_DETECT_INT IRQ_PF5
 653
 654 static int bfin_mmc_spi_init(struct device *dev,
 655         irqreturn_t (*detect_int)(int, void *), void *data)
 656 {
 657         return request_irq(MMC_SPI_CARD_DETECT_INT, detect_int,
 658                 IRQF_TRIGGER_FALLING, "mmc-spi-detect", data);
 659 }
 660
 661 static void bfin_mmc_spi_exit(struct device *dev, void *data)
 662 {
 663         free_irq(MMC_SPI_CARD_DETECT_INT, data);
 664 }
 665
 666 static struct mmc_spi_platform_data bfin_mmc_spi_pdata = {
 667         .init = bfin_mmc_spi_init,
 668         .exit = bfin_mmc_spi_exit,
 669         .detect_delay = 100, /* msecs */
 670 };
 671
 672 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 673         .enable_dma = 0,
 674         .bits_per_word = 8,
 675         .pio_interrupt = 0,
 676 };
 677 #endif
 678
 679 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 680 #include <linux/spi/ad7877.h>
 681 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 682         .enable_dma = 0,
 683         .bits_per_word = 16,
 684 };
 685
 686 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 687         .model                  = 7877,
 688         .vref_delay_usecs       = 50,   /* internal, no capacitor */
 689         .x_plate_ohms           = 419,
 690         .y_plate_ohms           = 486,
 691         .pressure_max           = 1000,
 692         .pressure_min           = 0,
 693         .stopacq_polarity       = 1,
 694         .first_conversion_delay = 3,
 695         .acquisition_time       = 1,
 696         .averaging              = 1,
 697         .pen_down_acc_interval  = 1,
 698 };
 699 #endif
 700
 701 #if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
 702 #include <linux/spi/ad7879.h>
 703 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 704         .model                  = 7879, /* Model = AD7879 */
 705         .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
 706         .pressure_max           = 10000,
 707         .pressure_min           = 0,
 708         .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
 709         .acquisition_time       = 1,    /* 4us acquisition time per sample */
 710         .median                 = 2,    /* do 8 measurements */
 711         .averaging              = 1,    /* take the average of 4 middle samples */
 712         .pen_down_acc_interval  = 255,  /* 9.4 ms */
 713         .gpio_export            = 1,    /* Export GPIO to gpiolib */
 714         .gpio_base              = -1,   /* Dynamic allocation */
 715 };
 716 #endif
 717
 718 #if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
 719 #include <linux/input/adxl34x.h>
 720 static const struct adxl34x_platform_data adxl34x_info = {
 721         .x_axis_offset = 0,
 722         .y_axis_offset = 0,
 723         .z_axis_offset = 0,
 724         .tap_threshold = 0x31,
 725         .tap_duration = 0x10,
 726         .tap_latency = 0x60,
 727         .tap_window = 0xF0,
 728         .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
 729         .act_axis_control = 0xFF,
 730         .activity_threshold = 5,
 731         .inactivity_threshold = 3,
 732         .inactivity_time = 4,
 733         .free_fall_threshold = 0x7,
 734         .free_fall_time = 0x20,
 735         .data_rate = 0x8,
 736         .data_range = ADXL_FULL_RES,
 737
 738         .ev_type = EV_ABS,
 739         .ev_code_x = ABS_X,             /* EV_REL */
 740         .ev_code_y = ABS_Y,             /* EV_REL */
 741         .ev_code_z = ABS_Z,             /* EV_REL */
 742
 743         .ev_code_tap = {BTN_TOUCH, BTN_TOUCH, BTN_TOUCH}, /* EV_KEY x,y,z */
 744
 745 /*      .ev_code_ff = KEY_F,*/          /* EV_KEY */
 746 /*      .ev_code_act_inactivity = KEY_A,*/      /* EV_KEY */
 747         .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
 748         .fifo_mode = ADXL_FIFO_STREAM,
 749 };
 750 #endif
 751
 752 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 753 static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
 754         .enable_dma = 0,
 755         .bits_per_word = 16,
 756 };
 757 #endif
 758
 759 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 760 static struct bfin5xx_spi_chip spidev_chip_info = {
 761         .enable_dma = 0,
 762         .bits_per_word = 8,
 763 };
 764 #endif
 765
 766 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 767 static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
 768         .enable_dma     = 0,
 769         .bits_per_word  = 8,
 770 };
 771 #endif
 772
 773 #if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
 774 static struct bfin5xx_spi_chip enc28j60_spi_chip_info = {
 775         .enable_dma     = 1,
 776         .bits_per_word  = 8,
 777         .cs_gpio = GPIO_PF10,
 778 };
 779 #endif
 780
 781 #if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
 782 static struct bfin5xx_spi_chip adf7021_spi_chip_info = {
 783         .bits_per_word = 16,
 784         .cs_gpio = GPIO_PF10,
 785 };
 786
 787 #include <linux/spi/adf702x.h>
 788 #define TXREG 0x0160A470
 789 static const u32 adf7021_regs[] = {
 790         0x09608FA0,
 791         0x00575011,
 792         0x00A7F092,
 793         0x2B141563,
 794         0x81F29E94,
 795         0x00003155,
 796         0x050A4F66,
 797         0x00000007,
 798         0x00000008,
 799         0x000231E9,
 800         0x3296354A,
 801         0x891A2B3B,
 802         0x00000D9C,
 803         0x0000000D,
 804         0x0000000E,
 805         0x0000000F,
 806 };
 807
 808 static struct adf702x_platform_data adf7021_platform_data = {
 809         .regs_base = (void *)SPORT1_TCR1,
 810         .dma_ch_rx = CH_SPORT1_RX,
 811         .dma_ch_tx = CH_SPORT1_TX,
 812         .irq_sport_err = IRQ_SPORT1_ERROR,
 813         .gpio_int_rfs = GPIO_PF8,
 814         .pin_req = {P_SPORT1_DTPRI, P_SPORT1_RFS, P_SPORT1_DRPRI,
 815                         P_SPORT1_RSCLK, P_SPORT1_TSCLK, 0},
 816         .adf702x_model = MODEL_ADF7021,
 817         .adf702x_regs = adf7021_regs,
 818         .tx_reg = TXREG,
 819 };
 820 static inline void adf702x_mac_init(void)
 821 {
 822         random_ether_addr(adf7021_platform_data.mac_addr);
 823 }
 824 #else
 825 static inline void adf702x_mac_init(void) {}
 826 #endif
 827
 828 #if defined(CONFIG_MTD_DATAFLASH) \
 829         || defined(CONFIG_MTD_DATAFLASH_MODULE)
 830
 831 static struct mtd_partition bfin_spi_dataflash_partitions[] = {
 832         {
 833                 .name = "bootloader(spi)",
 834                 .size = 0x00040000,
 835                 .offset = 0,
 836                 .mask_flags = MTD_CAP_ROM
 837         }, {
 838                 .name = "linux kernel(spi)",
 839                 .size = 0x180000,
 840                 .offset = MTDPART_OFS_APPEND,
 841         }, {
 842                 .name = "file system(spi)",
 843                 .size = MTDPART_SIZ_FULL,
 844                 .offset = MTDPART_OFS_APPEND,
 845         }
 846 };
 847
 848 static struct flash_platform_data bfin_spi_dataflash_data = {
 849         .name = "SPI Dataflash",
 850         .parts = bfin_spi_dataflash_partitions,
 851         .nr_parts = ARRAY_SIZE(bfin_spi_dataflash_partitions),
 852 };
 853
 854 /* DataFlash chip */
 855 static struct bfin5xx_spi_chip data_flash_chip_info = {
 856         .enable_dma = 0,         /* use dma transfer with this chip*/
 857         .bits_per_word = 8,
 858 };
 859 #endif
 860
 861 #if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
 862 static struct bfin5xx_spi_chip spi_adxl34x_chip_info = {
 863         .enable_dma = 0,         /* use dma transfer with this chip*/
 864         .bits_per_word = 8,
 865 };
 866 #endif
 867
 868 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 869 #if defined(CONFIG_MTD_M25P80) \
 870         || defined(CONFIG_MTD_M25P80_MODULE)
 871         {
 872                 /* the modalias must be the same as spi device driver name */
 873                 .modalias = "m25p80", /* Name of spi_driver for this device */
 874                 .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 875                 .bus_num = 0, /* Framework bus number */
 876                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 877                 .platform_data = &bfin_spi_flash_data,
 878                 .controller_data = &spi_flash_chip_info,
 879                 .mode = SPI_MODE_3,
 880         },
 881 #endif
 882 #if defined(CONFIG_MTD_DATAFLASH) \
 883         || defined(CONFIG_MTD_DATAFLASH_MODULE)
 884         {       /* DataFlash chip */
 885                 .modalias = "mtd_dataflash",
 886                 .max_speed_hz = 33250000,     /* max spi clock (SCK) speed in HZ */
 887                 .bus_num = 0, /* Framework bus number */
 888                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 889                 .platform_data = &bfin_spi_dataflash_data,
 890                 .controller_data = &data_flash_chip_info,
 891                 .mode = SPI_MODE_3,
 892         },
 893 #endif
 894 #if defined(CONFIG_BFIN_SPI_ADC) \
 895         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 896         {
 897                 .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
 898                 .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
 899                 .bus_num = 0, /* Framework bus number */
 900                 .chip_select = 1, /* Framework chip select. */
 901                 .platform_data = NULL, /* No spi_driver specific config */
 902                 .controller_data = &spi_adc_chip_info,
 903         },
 904 #endif
 905
 906 #if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
 907         || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
 908         {
 909                 .modalias = "ad1836",
 910                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 911                 .bus_num = 0,
 912                 .chip_select = 4,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
 913                 .controller_data = &ad1836_spi_chip_info,
 914                 .mode = SPI_MODE_3,
 915         },
 916 #endif
 917
 918 #if defined(CONFIG_SND_BF5XX_SOC_AD193X) || defined(CONFIG_SND_BF5XX_SOC_AD193X_MODULE)
 919         {
 920                 .modalias = "ad193x",
 921                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 922                 .bus_num = 0,
 923                 .chip_select = 5,
 924                 .controller_data = &ad1938_spi_chip_info,
 925                 .mode = SPI_MODE_3,
 926         },
 927 #endif
 928
 929 #if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
 930         {
 931                 .modalias = "ad714x_captouch",
 932                 .max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
 933                 .irq = IRQ_PF4,
 934                 .bus_num = 0,
 935                 .chip_select = 5,
 936                 .mode = SPI_MODE_3,
 937                 .platform_data = &ad7147_spi_platform_data,
 938                 .controller_data = &ad7147_spi_chip_info,
 939         },
 940 #endif
 941
 942 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 943         {
 944                 .modalias = "mmc_spi",
 945                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 946                 .bus_num = 0,
 947                 .chip_select = 4,
 948                 .platform_data = &bfin_mmc_spi_pdata,
 949                 .controller_data = &mmc_spi_chip_info,
 950                 .mode = SPI_MODE_3,
 951         },
 952 #endif
 953 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 954         {
 955                 .modalias               = "ad7877",
 956                 .platform_data          = &bfin_ad7877_ts_info,
 957                 .irq                    = IRQ_PF6,
 958                 .max_speed_hz   = 12500000,     /* max spi clock (SCK) speed in HZ */
 959                 .bus_num        = 0,
 960                 .chip_select  = 1,
 961                 .controller_data = &spi_ad7877_chip_info,
 962         },
 963 #endif
 964 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 965         {
 966                 .modalias = "ad7879",
 967                 .platform_data = &bfin_ad7879_ts_info,
 968                 .irq = IRQ_PF7,
 969                 .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
 970                 .bus_num = 0,
 971                 .chip_select = 1,
 972                 .controller_data = &spi_ad7879_chip_info,
 973                 .mode = SPI_CPHA | SPI_CPOL,
 974         },
 975 #endif
 976 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 977         {
 978                 .modalias = "spidev",
 979                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 980                 .bus_num = 0,
 981                 .chip_select = 1,
 982                 .controller_data = &spidev_chip_info,
 983         },
 984 #endif
 985 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 986         {
 987                 .modalias = "bfin-lq035q1-spi",
 988                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 989                 .bus_num = 0,
 990                 .chip_select = 2,
 991                 .controller_data = &lq035q1_spi_chip_info,
 992                 .mode = SPI_CPHA | SPI_CPOL,
 993         },
 994 #endif
 995 #if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
 996         {
 997                 .modalias = "enc28j60",
 998                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 999                 .irq = IRQ_PF6,
1000                 .bus_num = 0,
1001                 .chip_select = 0,       /* GPIO controlled SSEL */
1002                 .controller_data = &enc28j60_spi_chip_info,
1003                 .mode = SPI_MODE_0,
1004         },
1005 #endif
1006 #if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
1007         {
1008                 .modalias       = "adxl34x",
1009                 .platform_data  = &adxl34x_info,
1010                 .irq            = IRQ_PF6,
1011                 .max_speed_hz   = 5000000,    /* max spi clock (SCK) speed in HZ */
1012                 .bus_num        = 0,
1013                 .chip_select    = 2,
1014                 .controller_data = &spi_adxl34x_chip_info,
1015                 .mode = SPI_MODE_3,
1016         },
1017 #endif
1018 #if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
1019         {
1020                 .modalias = "adf702x",
1021                 .max_speed_hz = 16000000,     /* max spi clock (SCK) speed in HZ */
1022                 .bus_num = 0,
1023                 .chip_select = 0,       /* GPIO controlled SSEL */
1024                 .controller_data = &adf7021_spi_chip_info,
1025                 .platform_data = &adf7021_platform_data,
1026                 .mode = SPI_MODE_0,
1027         },
1028 #endif
1029
1030 };
1031
1032 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
1033 /* SPI controller data */
1034 static struct bfin5xx_spi_master bfin_spi0_info = {
1035         .num_chipselect = 8,
1036         .enable_dma = 1,  /* master has the ability to do dma transfer */
1037         .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
1038 };
1039
1040 /* SPI (0) */
1041 static struct resource bfin_spi0_resource[] = {
1042         [0] = {
1043                 .start = SPI0_REGBASE,
1044                 .end   = SPI0_REGBASE + 0xFF,
1045                 .flags = IORESOURCE_MEM,
1046                 },
1047         [1] = {
1048                 .start = CH_SPI,
1049                 .end   = CH_SPI,
1050                 .flags = IORESOURCE_DMA,
1051         },
1052         [2] = {
1053                 .start = IRQ_SPI,
1054                 .end   = IRQ_SPI,
1055                 .flags = IORESOURCE_IRQ,
1056         },
1057 };
1058
1059 static struct platform_device bfin_spi0_device = {
1060         .name = "bfin-spi",
1061         .id = 0, /* Bus number */
1062         .num_resources = ARRAY_SIZE(bfin_spi0_resource),
1063         .resource = bfin_spi0_resource,
1064         .dev = {
1065                 .platform_data = &bfin_spi0_info, /* Passed to driver */
1066         },
1067 };
1068 #endif  /* spi master and devices */
1069
1070 #if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
1071
1072 /* SPORT SPI controller data */
1073 static struct bfin5xx_spi_master bfin_sport_spi0_info = {
1074         .num_chipselect = 1, /* master only supports one device */
1075         .enable_dma = 0,  /* master don't support DMA */
1076         .pin_req = {P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_DRPRI,
1077                 P_SPORT0_RSCLK, P_SPORT0_TFS, P_SPORT0_RFS, 0},
1078 };
1079
1080 static struct resource bfin_sport_spi0_resource[] = {
1081         [0] = {
1082                 .start = SPORT0_TCR1,
1083                 .end   = SPORT0_TCR1 + 0xFF,
1084                 .flags = IORESOURCE_MEM,
1085                 },
1086         [1] = {
1087                 .start = IRQ_SPORT0_ERROR,
1088                 .end   = IRQ_SPORT0_ERROR,
1089                 .flags = IORESOURCE_IRQ,
1090                 },
1091 };
1092
1093 static struct platform_device bfin_sport_spi0_device = {
1094         .name = "bfin-sport-spi",
1095         .id = 1, /* Bus number */
1096         .num_resources = ARRAY_SIZE(bfin_sport_spi0_resource),
1097         .resource = bfin_sport_spi0_resource,
1098         .dev = {
1099                 .platform_data = &bfin_sport_spi0_info, /* Passed to driver */
1100         },
1101 };
1102
1103 static struct bfin5xx_spi_master bfin_sport_spi1_info = {
1104         .num_chipselect = 1, /* master only supports one device */
1105         .enable_dma = 0,  /* master don't support DMA */
1106         .pin_req = {P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_DRPRI,
1107                 P_SPORT1_RSCLK, P_SPORT1_TFS, P_SPORT1_RFS, 0},
1108 };
1109
1110 static struct resource bfin_sport_spi1_resource[] = {
1111         [0] = {
1112                 .start = SPORT1_TCR1,
1113                 .end   = SPORT1_TCR1 + 0xFF,
1114                 .flags = IORESOURCE_MEM,
1115                 },
1116         [1] = {
1117                 .start = IRQ_SPORT1_ERROR,
1118                 .end   = IRQ_SPORT1_ERROR,
1119                 .flags = IORESOURCE_IRQ,
1120                 },
1121 };
1122
1123 static struct platform_device bfin_sport_spi1_device = {
1124         .name = "bfin-sport-spi",
1125         .id = 2, /* Bus number */
1126         .num_resources = ARRAY_SIZE(bfin_sport_spi1_resource),
1127         .resource = bfin_sport_spi1_resource,
1128         .dev = {
1129                 .platform_data = &bfin_sport_spi1_info, /* Passed to driver */
1130         },
1131 };
1132
1133 #endif  /* sport spi master and devices */
1134
1135 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
1136 static struct platform_device bfin_fb_device = {
1137         .name = "bf537-lq035",
1138 };
1139 #endif
1140
1141 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
1142 #include <asm/bfin-lq035q1.h>
1143
1144 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
1145         .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
1146         .ppi_mode = USE_RGB565_16_BIT_PPI,
1147         .use_bl = 0,    /* let something else control the LCD Blacklight */
1148         .gpio_bl = GPIO_PF7,
1149 };
1150
1151 static struct resource bfin_lq035q1_resources[] = {
1152         {
1153                 .start = IRQ_PPI_ERROR,
1154                 .end = IRQ_PPI_ERROR,
1155                 .flags = IORESOURCE_IRQ,
1156         },
1157 };
1158
1159 static struct platform_device bfin_lq035q1_device = {
1160         .name           = "bfin-lq035q1",
1161         .id             = -1,
1162         .num_resources  = ARRAY_SIZE(bfin_lq035q1_resources),
1163         .resource       = bfin_lq035q1_resources,
1164         .dev            = {
1165                 .platform_data = &bfin_lq035q1_data,
1166         },
1167 };
1168 #endif
1169
1170 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
1171 #ifdef CONFIG_SERIAL_BFIN_UART0
1172 static struct resource bfin_uart0_resources[] = {
1173         {
1174                 .start = UART0_THR,
1175                 .end = UART0_GCTL+2,
1176                 .flags = IORESOURCE_MEM,
1177         },
1178         {
1179                 .start = IRQ_UART0_RX,
1180                 .end = IRQ_UART0_RX+1,
1181                 .flags = IORESOURCE_IRQ,
1182         },
1183         {
1184                 .start = IRQ_UART0_ERROR,
1185                 .end = IRQ_UART0_ERROR,
1186                 .flags = IORESOURCE_IRQ,
1187         },
1188         {
1189                 .start = CH_UART0_TX,
1190                 .end = CH_UART0_TX,
1191                 .flags = IORESOURCE_DMA,
1192         },
1193         {
1194                 .start = CH_UART0_RX,
1195                 .end = CH_UART0_RX,
1196                 .flags = IORESOURCE_DMA,
1197         },
1198 #ifdef CONFIG_BFIN_UART0_CTSRTS
1199         {       /* CTS pin */
1200                 .start = GPIO_PG7,
1201                 .end = GPIO_PG7,
1202                 .flags = IORESOURCE_IO,
1203         },
1204         {       /* RTS pin */
1205                 .start = GPIO_PG6,
1206                 .end = GPIO_PG6,
1207                 .flags = IORESOURCE_IO,
1208         },
1209 #endif
1210 };
1211
1212 unsigned short bfin_uart0_peripherals[] = {
1213         P_UART0_TX, P_UART0_RX, 0
1214 };
1215
1216 static struct platform_device bfin_uart0_device = {
1217         .name = "bfin-uart",
1218         .id = 0,
1219         .num_resources = ARRAY_SIZE(bfin_uart0_resources),
1220         .resource = bfin_uart0_resources,
1221         .dev = {
1222                 .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
1223         },
1224 };
1225 #endif
1226 #ifdef CONFIG_SERIAL_BFIN_UART1
1227 static struct resource bfin_uart1_resources[] = {
1228         {
1229                 .start = UART1_THR,
1230                 .end = UART1_GCTL+2,
1231                 .flags = IORESOURCE_MEM,
1232         },
1233         {
1234                 .start = IRQ_UART1_RX,
1235                 .end = IRQ_UART1_RX+1,
1236                 .flags = IORESOURCE_IRQ,
1237         },
1238         {
1239                 .start = IRQ_UART1_ERROR,
1240                 .end = IRQ_UART1_ERROR,
1241                 .flags = IORESOURCE_IRQ,
1242         },
1243         {
1244                 .start = CH_UART1_TX,
1245                 .end = CH_UART1_TX,
1246                 .flags = IORESOURCE_DMA,
1247         },
1248         {
1249                 .start = CH_UART1_RX,
1250                 .end = CH_UART1_RX,
1251                 .flags = IORESOURCE_DMA,
1252         },
1253 };
1254
1255 unsigned short bfin_uart1_peripherals[] = {
1256         P_UART1_TX, P_UART1_RX, 0
1257 };
1258
1259 static struct platform_device bfin_uart1_device = {
1260         .name = "bfin-uart",
1261         .id = 1,
1262         .num_resources = ARRAY_SIZE(bfin_uart1_resources),
1263         .resource = bfin_uart1_resources,
1264         .dev = {
1265                 .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
1266         },
1267 };
1268 #endif
1269 #endif
1270
1271 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
1272 #ifdef CONFIG_BFIN_SIR0
1273 static struct resource bfin_sir0_resources[] = {
1274         {
1275                 .start = 0xFFC00400,
1276                 .end = 0xFFC004FF,
1277                 .flags = IORESOURCE_MEM,
1278         },
1279         {
1280                 .start = IRQ_UART0_RX,
1281                 .end = IRQ_UART0_RX+1,
1282                 .flags = IORESOURCE_IRQ,
1283         },
1284         {
1285                 .start = CH_UART0_RX,
1286                 .end = CH_UART0_RX+1,
1287                 .flags = IORESOURCE_DMA,
1288         },
1289 };
1290
1291 static struct platform_device bfin_sir0_device = {
1292         .name = "bfin_sir",
1293         .id = 0,
1294         .num_resources = ARRAY_SIZE(bfin_sir0_resources),
1295         .resource = bfin_sir0_resources,
1296 };
1297 #endif
1298 #ifdef CONFIG_BFIN_SIR1
1299 static struct resource bfin_sir1_resources[] = {
1300         {
1301                 .start = 0xFFC02000,
1302                 .end = 0xFFC020FF,
1303                 .flags = IORESOURCE_MEM,
1304         },
1305         {
1306                 .start = IRQ_UART1_RX,
1307                 .end = IRQ_UART1_RX+1,
1308                 .flags = IORESOURCE_IRQ,
1309         },
1310         {
1311                 .start = CH_UART1_RX,
1312                 .end = CH_UART1_RX+1,
1313                 .flags = IORESOURCE_DMA,
1314         },
1315 };
1316
1317 static struct platform_device bfin_sir1_device = {
1318         .name = "bfin_sir",
1319         .id = 1,
1320         .num_resources = ARRAY_SIZE(bfin_sir1_resources),
1321         .resource = bfin_sir1_resources,
1322 };
1323 #endif
1324 #endif
1325
1326 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
1327 static struct resource bfin_twi0_resource[] = {
1328         [0] = {
1329                 .start = TWI0_REGBASE,
1330                 .end   = TWI0_REGBASE,
1331                 .flags = IORESOURCE_MEM,
1332         },
1333         [1] = {
1334                 .start = IRQ_TWI,
1335                 .end   = IRQ_TWI,
1336                 .flags = IORESOURCE_IRQ,
1337         },
1338 };
1339
1340 static struct platform_device i2c_bfin_twi_device = {
1341         .name = "i2c-bfin-twi",
1342         .id = 0,
1343         .num_resources = ARRAY_SIZE(bfin_twi0_resource),
1344         .resource = bfin_twi0_resource,
1345 };
1346 #endif
1347
1348 #if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
1349 static const unsigned short adp5588_keymap[ADP5588_KEYMAPSIZE] = {
1350         [0]      = KEY_GRAVE,
1351         [1]      = KEY_1,
1352         [2]      = KEY_2,
1353         [3]      = KEY_3,
1354         [4]      = KEY_4,
1355         [5]      = KEY_5,
1356         [6]      = KEY_6,
1357         [7]      = KEY_7,
1358         [8]      = KEY_8,
1359         [9]      = KEY_9,
1360         [10]     = KEY_0,
1361         [11]     = KEY_MINUS,
1362         [12]     = KEY_EQUAL,
1363         [13]     = KEY_BACKSLASH,
1364         [15]     = KEY_KP0,
1365         [16]     = KEY_Q,
1366         [17]     = KEY_W,
1367         [18]     = KEY_E,
1368         [19]     = KEY_R,
1369         [20]     = KEY_T,
1370         [21]     = KEY_Y,
1371         [22]     = KEY_U,
1372         [23]     = KEY_I,
1373         [24]     = KEY_O,
1374         [25]     = KEY_P,
1375         [26]     = KEY_LEFTBRACE,
1376         [27]     = KEY_RIGHTBRACE,
1377         [29]     = KEY_KP1,
1378         [30]     = KEY_KP2,
1379         [31]     = KEY_KP3,
1380         [32]     = KEY_A,
1381         [33]     = KEY_S,
1382         [34]     = KEY_D,
1383         [35]     = KEY_F,
1384         [36]     = KEY_G,
1385         [37]     = KEY_H,
1386         [38]     = KEY_J,
1387         [39]     = KEY_K,
1388         [40]     = KEY_L,
1389         [41]     = KEY_SEMICOLON,
1390         [42]     = KEY_APOSTROPHE,
1391         [43]     = KEY_BACKSLASH,
1392         [45]     = KEY_KP4,
1393         [46]     = KEY_KP5,
1394         [47]     = KEY_KP6,
1395         [48]     = KEY_102ND,
1396         [49]     = KEY_Z,
1397         [50]     = KEY_X,
1398         [51]     = KEY_C,
1399         [52]     = KEY_V,
1400         [53]     = KEY_B,
1401         [54]     = KEY_N,
1402         [55]     = KEY_M,
1403         [56]     = KEY_COMMA,
1404         [57]     = KEY_DOT,
1405         [58]     = KEY_SLASH,
1406         [60]     = KEY_KPDOT,
1407         [61]     = KEY_KP7,
1408         [62]     = KEY_KP8,
1409         [63]     = KEY_KP9,
1410         [64]     = KEY_SPACE,
1411         [65]     = KEY_BACKSPACE,
1412         [66]     = KEY_TAB,
1413         [67]     = KEY_KPENTER,
1414         [68]     = KEY_ENTER,
1415         [69]     = KEY_ESC,
1416         [70]     = KEY_DELETE,
1417         [74]     = KEY_KPMINUS,
1418         [76]     = KEY_UP,
1419         [77]     = KEY_DOWN,
1420         [78]     = KEY_RIGHT,
1421         [79]     = KEY_LEFT,
1422 };
1423
1424 static struct adp5588_kpad_platform_data adp5588_kpad_data = {
1425         .rows           = 8,
1426         .cols           = 10,
1427         .keymap         = adp5588_keymap,
1428         .keymapsize     = ARRAY_SIZE(adp5588_keymap),
1429         .repeat         = 0,
1430 };
1431 #endif
1432
1433 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
1434 #include <linux/mfd/adp5520.h>
1435
1436         /*
1437          *  ADP5520/5501 Backlight Data
1438          */
1439
1440 static struct adp5520_backlight_platform_data adp5520_backlight_data = {
1441         .fade_in                = ADP5520_FADE_T_1200ms,
1442         .fade_out               = ADP5520_FADE_T_1200ms,
1443         .fade_led_law           = ADP5520_BL_LAW_LINEAR,
1444         .en_ambl_sens           = 1,
1445         .abml_filt              = ADP5520_BL_AMBL_FILT_640ms,
1446         .l1_daylight_max        = ADP5520_BL_CUR_mA(15),
1447         .l1_daylight_dim        = ADP5520_BL_CUR_mA(0),
1448         .l2_office_max          = ADP5520_BL_CUR_mA(7),
1449         .l2_office_dim          = ADP5520_BL_CUR_mA(0),
1450         .l3_dark_max            = ADP5520_BL_CUR_mA(3),
1451         .l3_dark_dim            = ADP5520_BL_CUR_mA(0),
1452         .l2_trip                = ADP5520_L2_COMP_CURR_uA(700),
1453         .l2_hyst                = ADP5520_L2_COMP_CURR_uA(50),
1454         .l3_trip                = ADP5520_L3_COMP_CURR_uA(80),
1455         .l3_hyst                = ADP5520_L3_COMP_CURR_uA(20),
1456 };
1457
1458         /*
1459          *  ADP5520/5501 LEDs Data
1460          */
1461
1462 static struct led_info adp5520_leds[] = {
1463         {
1464                 .name = "adp5520-led1",
1465                 .default_trigger = "none",
1466                 .flags = FLAG_ID_ADP5520_LED1_ADP5501_LED0 | ADP5520_LED_OFFT_600ms,
1467         },
1468 #ifdef ADP5520_EN_ALL_LEDS
1469         {
1470                 .name = "adp5520-led2",
1471                 .default_trigger = "none",
1472                 .flags = FLAG_ID_ADP5520_LED2_ADP5501_LED1,
1473         },
1474         {
1475                 .name = "adp5520-led3",
1476                 .default_trigger = "none",
1477                 .flags = FLAG_ID_ADP5520_LED3_ADP5501_LED2,
1478         },
1479 #endif
1480 };
1481
1482 static struct adp5520_leds_platform_data adp5520_leds_data = {
1483         .num_leds = ARRAY_SIZE(adp5520_leds),
1484         .leds = adp5520_leds,
1485         .fade_in = ADP5520_FADE_T_600ms,
1486         .fade_out = ADP5520_FADE_T_600ms,
1487         .led_on_time = ADP5520_LED_ONT_600ms,
1488 };
1489
1490         /*
1491          *  ADP5520 GPIO Data
1492          */
1493
1494 static struct adp5520_gpio_platform_data adp5520_gpio_data = {
1495         .gpio_start = 50,
1496         .gpio_en_mask = ADP5520_GPIO_C1 | ADP5520_GPIO_C2 | ADP5520_GPIO_R2,
1497         .gpio_pullup_mask = ADP5520_GPIO_C1 | ADP5520_GPIO_C2 | ADP5520_GPIO_R2,
1498 };
1499
1500         /*
1501          *  ADP5520 Keypad Data
1502          */
1503
1504 static const unsigned short adp5520_keymap[ADP5520_KEYMAPSIZE] = {
1505         [ADP5520_KEY(0, 0)]     = KEY_GRAVE,
1506         [ADP5520_KEY(0, 1)]     = KEY_1,
1507         [ADP5520_KEY(0, 2)]     = KEY_2,
1508         [ADP5520_KEY(0, 3)]     = KEY_3,
1509         [ADP5520_KEY(1, 0)]     = KEY_4,
1510         [ADP5520_KEY(1, 1)]     = KEY_5,
1511         [ADP5520_KEY(1, 2)]     = KEY_6,
1512         [ADP5520_KEY(1, 3)]     = KEY_7,
1513         [ADP5520_KEY(2, 0)]     = KEY_8,
1514         [ADP5520_KEY(2, 1)]     = KEY_9,
1515         [ADP5520_KEY(2, 2)]     = KEY_0,
1516         [ADP5520_KEY(2, 3)]     = KEY_MINUS,
1517         [ADP5520_KEY(3, 0)]     = KEY_EQUAL,
1518         [ADP5520_KEY(3, 1)]     = KEY_BACKSLASH,
1519         [ADP5520_KEY(3, 2)]     = KEY_BACKSPACE,
1520         [ADP5520_KEY(3, 3)]     = KEY_ENTER,
1521 };
1522
1523 static struct adp5520_keys_platform_data adp5520_keys_data = {
1524         .rows_en_mask   = ADP5520_ROW_R3 | ADP5520_ROW_R2 | ADP5520_ROW_R1 | ADP5520_ROW_R0,
1525         .cols_en_mask   = ADP5520_COL_C3 | ADP5520_COL_C2 | ADP5520_COL_C1 | ADP5520_COL_C0,
1526         .keymap         = adp5520_keymap,
1527         .keymapsize     = ARRAY_SIZE(adp5520_keymap),
1528         .repeat         = 0,
1529 };
1530
1531         /*
1532          *  ADP5520/5501 Multifuction Device Init Data
1533          */
1534
1535 static struct adp5520_platform_data adp5520_pdev_data = {
1536         .backlight = &adp5520_backlight_data,
1537         .leds = &adp5520_leds_data,
1538         .gpio = &adp5520_gpio_data,
1539         .keys = &adp5520_keys_data,
1540 };
1541
1542 #endif
1543
1544 #if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
1545 static struct adp5588_gpio_platform_data adp5588_gpio_data = {
1546         .gpio_start = 50,
1547         .pullup_dis_mask = 0,
1548 };
1549 #endif
1550
1551 #if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
1552 #include <linux/i2c/adp8870.h>
1553 static struct led_info adp8870_leds[] = {
1554         {
1555                 .name = "adp8870-led7",
1556                 .default_trigger = "none",
1557                 .flags = ADP8870_LED_D7 | ADP8870_LED_OFFT_600ms,
1558         },
1559 };
1560
1561
1562 static struct adp8870_backlight_platform_data adp8870_pdata = {
1563         .bl_led_assign = ADP8870_BL_D1 | ADP8870_BL_D2 | ADP8870_BL_D3 |
1564                          ADP8870_BL_D4 | ADP8870_BL_D5 | ADP8870_BL_D6, /* 1 = Backlight 0 = Individual LED */
1565         .pwm_assign = 0,                                /* 1 = Enables PWM mode */
1566
1567         .bl_fade_in = ADP8870_FADE_T_1200ms,            /* Backlight Fade-In Timer */
1568         .bl_fade_out = ADP8870_FADE_T_1200ms,           /* Backlight Fade-Out Timer */
1569         .bl_fade_law = ADP8870_FADE_LAW_CUBIC1,         /* fade-on/fade-off transfer characteristic */
1570
1571         .en_ambl_sens = 1,                              /* 1 = enable ambient light sensor */
1572         .abml_filt = ADP8870_BL_AMBL_FILT_320ms,        /* Light sensor filter time */
1573
1574         .l1_daylight_max = ADP8870_BL_CUR_mA(20),       /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1575         .l1_daylight_dim = ADP8870_BL_CUR_mA(0),        /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1576         .l2_bright_max = ADP8870_BL_CUR_mA(14),         /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1577         .l2_bright_dim = ADP8870_BL_CUR_mA(0),          /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1578         .l3_office_max = ADP8870_BL_CUR_mA(6),          /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1579         .l3_office_dim = ADP8870_BL_CUR_mA(0),          /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1580         .l4_indoor_max = ADP8870_BL_CUR_mA(3),          /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1581         .l4_indor_dim = ADP8870_BL_CUR_mA(0),           /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1582         .l5_dark_max = ADP8870_BL_CUR_mA(2),            /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1583         .l5_dark_dim = ADP8870_BL_CUR_mA(0),            /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1584
1585         .l2_trip = ADP8870_L2_COMP_CURR_uA(710),        /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
1586         .l2_hyst = ADP8870_L2_COMP_CURR_uA(73),         /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
1587         .l3_trip = ADP8870_L3_COMP_CURR_uA(389),        /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
1588         .l3_hyst = ADP8870_L3_COMP_CURR_uA(54),         /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
1589         .l4_trip = ADP8870_L4_COMP_CURR_uA(167),        /* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */
1590         .l4_hyst = ADP8870_L4_COMP_CURR_uA(16),         /* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */
1591         .l5_trip = ADP8870_L5_COMP_CURR_uA(43),         /* use L5_COMP_CURR_uA(I) 0 <= I <= 138 uA */
1592         .l5_hyst = ADP8870_L5_COMP_CURR_uA(11),         /* use L6_COMP_CURR_uA(I) 0 <= I <= 138 uA */
1593
1594         .leds = adp8870_leds,
1595         .num_leds = ARRAY_SIZE(adp8870_leds),
1596         .led_fade_law = ADP8870_FADE_LAW_SQUARE,        /* fade-on/fade-off transfer characteristic */
1597         .led_fade_in = ADP8870_FADE_T_600ms,
1598         .led_fade_out = ADP8870_FADE_T_600ms,
1599         .led_on_time = ADP8870_LED_ONT_200ms,
1600 };
1601 #endif
1602
1603 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
1604 #if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
1605         {
1606                 I2C_BOARD_INFO("ad7142_captouch", 0x2C),
1607                 .irq = IRQ_PG5,
1608                 .platform_data = (void *)&ad7142_i2c_platform_data,
1609         },
1610 #endif
1611 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
1612         {
1613                 I2C_BOARD_INFO("pcf8574_lcd", 0x22),
1614         },
1615 #endif
1616 #if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
1617         {
1618                 I2C_BOARD_INFO("pcf8574_keypad", 0x27),
1619                 .irq = IRQ_PG6,
1620         },
1621 #endif
1622 #if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
1623         {
1624                 I2C_BOARD_INFO("ad7879", 0x2F),
1625                 .irq = IRQ_PG5,
1626                 .platform_data = (void *)&bfin_ad7879_ts_info,
1627         },
1628 #endif
1629 #if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
1630         {
1631                 I2C_BOARD_INFO("adp5588-keys", 0x34),
1632                 .irq = IRQ_PG0,
1633                 .platform_data = (void *)&adp5588_kpad_data,
1634         },
1635 #endif
1636 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
1637         {
1638                 I2C_BOARD_INFO("pmic-adp5520", 0x32),
1639                 .irq = IRQ_PG0,
1640                 .platform_data = (void *)&adp5520_pdev_data,
1641         },
1642 #endif
1643 #if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
1644         {
1645                 I2C_BOARD_INFO("adxl34x", 0x53),
1646                 .irq = IRQ_PG3,
1647                 .platform_data = (void *)&adxl34x_info,
1648         },
1649 #endif
1650 #if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
1651         {
1652                 I2C_BOARD_INFO("adp5588-gpio", 0x34),
1653                 .platform_data = (void *)&adp5588_gpio_data,
1654         },
1655 #endif
1656 #if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
1657         {
1658                 I2C_BOARD_INFO("bfin-adv7393", 0x2B),
1659         },
1660 #endif
1661 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
1662         {
1663                 I2C_BOARD_INFO("bf537-lq035-ad5280", 0x2C),
1664         },
1665 #endif
1666 #if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
1667         {
1668                 I2C_BOARD_INFO("adp8870", 0x2B),
1669                 .platform_data = (void *)&adp8870_pdata,
1670         },
1671 #endif
1672 #if defined(CONFIG_SND_SOC_ADAU1371) || defined(CONFIG_SND_SOC_ADAU1371_MODULE)
1673         {
1674                 I2C_BOARD_INFO("adau1371", 0x1A),
1675         },
1676 #endif
1677 #if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
1678         {
1679                 I2C_BOARD_INFO("adau1761", 0x38),
1680         },
1681 #endif
1682 #if defined(CONFIG_AD525X_DPOT) || defined(CONFIG_AD525X_DPOT_MODULE)
1683         {
1684                 I2C_BOARD_INFO("ad5258", 0x18),
1685         },
1686 #endif
1687 #if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
1688         {
1689                 I2C_BOARD_INFO("ssm2602", 0x1b),
1690         },
1691 #endif
1692 };
1693
1694 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1695 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1696 static struct resource bfin_sport0_uart_resources[] = {
1697         {
1698                 .start = SPORT0_TCR1,
1699                 .end = SPORT0_MRCS3+4,
1700                 .flags = IORESOURCE_MEM,
1701         },
1702         {
1703                 .start = IRQ_SPORT0_RX,
1704                 .end = IRQ_SPORT0_RX+1,
1705                 .flags = IORESOURCE_IRQ,
1706         },
1707         {
1708                 .start = IRQ_SPORT0_ERROR,
1709                 .end = IRQ_SPORT0_ERROR,
1710                 .flags = IORESOURCE_IRQ,
1711         },
1712 };
1713
1714 unsigned short bfin_sport0_peripherals[] = {
1715         P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
1716         P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
1717 };
1718
1719 static struct platform_device bfin_sport0_uart_device = {
1720         .name = "bfin-sport-uart",
1721         .id = 0,
1722         .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
1723         .resource = bfin_sport0_uart_resources,
1724         .dev = {
1725                 .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
1726         },
1727 };
1728 #endif
1729 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1730 static struct resource bfin_sport1_uart_resources[] = {
1731         {
1732                 .start = SPORT1_TCR1,
1733                 .end = SPORT1_MRCS3+4,
1734                 .flags = IORESOURCE_MEM,
1735         },
1736         {
1737                 .start = IRQ_SPORT1_RX,
1738                 .end = IRQ_SPORT1_RX+1,
1739                 .flags = IORESOURCE_IRQ,
1740         },
1741         {
1742                 .start = IRQ_SPORT1_ERROR,
1743                 .end = IRQ_SPORT1_ERROR,
1744                 .flags = IORESOURCE_IRQ,
1745         },
1746 };
1747
1748 unsigned short bfin_sport1_peripherals[] = {
1749         P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
1750         P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
1751 };
1752
1753 static struct platform_device bfin_sport1_uart_device = {
1754         .name = "bfin-sport-uart",
1755         .id = 1,
1756         .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
1757         .resource = bfin_sport1_uart_resources,
1758         .dev = {
1759                 .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
1760         },
1761 };
1762 #endif
1763 #endif
1764
1765 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
1766 #define CF_IDE_NAND_CARD_USE_HDD_INTERFACE
1767 /* #define CF_IDE_NAND_CARD_USE_CF_IN_COMMON_MEMORY_MODE */
1768
1769 #ifdef CF_IDE_NAND_CARD_USE_HDD_INTERFACE
1770 #define PATA_INT        IRQ_PF5
1771 static struct pata_platform_info bfin_pata_platform_data = {
1772         .ioport_shift = 1,
1773         .irq_flags = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
1774 };
1775
1776 static struct resource bfin_pata_resources[] = {
1777         {
1778                 .start = 0x20314020,
1779                 .end = 0x2031403F,
1780                 .flags = IORESOURCE_MEM,
1781         },
1782         {
1783                 .start = 0x2031401C,
1784                 .end = 0x2031401F,
1785                 .flags = IORESOURCE_MEM,
1786         },
1787         {
1788                 .start = PATA_INT,
1789                 .end = PATA_INT,
1790                 .flags = IORESOURCE_IRQ,
1791         },
1792 };
1793 #elif defined(CF_IDE_NAND_CARD_USE_CF_IN_COMMON_MEMORY_MODE)
1794 static struct pata_platform_info bfin_pata_platform_data = {
1795         .ioport_shift = 0,
1796 };
1797 /* CompactFlash Storage Card Memory Mapped Adressing
1798  * /REG = A11 = 1
1799  */
1800 static struct resource bfin_pata_resources[] = {
1801         {
1802                 .start = 0x20211800,
1803                 .end = 0x20211807,
1804                 .flags = IORESOURCE_MEM,
1805         },
1806         {
1807                 .start = 0x2021180E,    /* Device Ctl */
1808                 .end = 0x2021180E,
1809                 .flags = IORESOURCE_MEM,
1810         },
1811 };
1812 #endif
1813
1814 static struct platform_device bfin_pata_device = {
1815         .name = "pata_platform",
1816         .id = -1,
1817         .num_resources = ARRAY_SIZE(bfin_pata_resources),
1818         .resource = bfin_pata_resources,
1819         .dev = {
1820                 .platform_data = &bfin_pata_platform_data,
1821         }
1822 };
1823 #endif
1824
1825 static const unsigned int cclk_vlev_datasheet[] =
1826 {
1827         VRPAIR(VLEV_085, 250000000),
1828         VRPAIR(VLEV_090, 376000000),
1829         VRPAIR(VLEV_095, 426000000),
1830         VRPAIR(VLEV_100, 426000000),
1831         VRPAIR(VLEV_105, 476000000),
1832         VRPAIR(VLEV_110, 476000000),
1833         VRPAIR(VLEV_115, 476000000),
1834         VRPAIR(VLEV_120, 500000000),
1835         VRPAIR(VLEV_125, 533000000),
1836         VRPAIR(VLEV_130, 600000000),
1837 };
1838
1839 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
1840         .tuple_tab = cclk_vlev_datasheet,
1841         .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
1842         .vr_settling_time = 25 /* us */,
1843 };
1844
1845 static struct platform_device bfin_dpmc = {
1846         .name = "bfin dpmc",
1847         .dev = {
1848                 .platform_data = &bfin_dmpc_vreg_data,
1849         },
1850 };
1851
1852 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
1853 static struct platform_device bfin_i2s = {
1854         .name = "bfin-i2s",
1855         .id = CONFIG_SND_BF5XX_SPORT_NUM,
1856         /* TODO: add platform data here */
1857 };
1858 #endif
1859
1860 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
1861 static struct platform_device bfin_tdm = {
1862         .name = "bfin-tdm",
1863         .id = CONFIG_SND_BF5XX_SPORT_NUM,
1864         /* TODO: add platform data here */
1865 };
1866 #endif
1867
1868 #if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
1869 static struct platform_device bfin_ac97 = {
1870         .name = "bfin-ac97",
1871         .id = CONFIG_SND_BF5XX_SPORT_NUM,
1872         /* TODO: add platform data here */
1873 };
1874 #endif
1875
1876 static struct platform_device *stamp_devices[] __initdata = {
1877
1878         &bfin_dpmc,
1879
1880 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
1881         &bfin_pcmcia_cf_device,
1882 #endif
1883
1884 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
1885         &rtc_device,
1886 #endif
1887
1888 #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
1889         &sl811_hcd_device,
1890 #endif
1891
1892 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
1893         &isp1362_hcd_device,
1894 #endif
1895
1896 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
1897         &bfin_isp1760_device,
1898 #endif
1899
1900 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
1901         &smc91x_device,
1902 #endif
1903
1904 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
1905         &dm9000_device,
1906 #endif
1907
1908 #if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
1909         &bfin_can_device,
1910 #endif
1911
1912 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
1913         &bfin_mii_bus,
1914         &bfin_mac_device,
1915 #endif
1916
1917 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
1918         &net2272_bfin_device,
1919 #endif
1920
1921 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
1922         &bfin_spi0_device,
1923 #endif
1924
1925 #if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
1926         &bfin_sport_spi0_device,
1927         &bfin_sport_spi1_device,
1928 #endif
1929
1930 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
1931         &bfin_fb_device,
1932 #endif
1933
1934 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
1935         &bfin_lq035q1_device,
1936 #endif
1937
1938 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
1939 #ifdef CONFIG_SERIAL_BFIN_UART0
1940         &bfin_uart0_device,
1941 #endif
1942 #ifdef CONFIG_SERIAL_BFIN_UART1
1943         &bfin_uart1_device,
1944 #endif
1945 #endif
1946
1947 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
1948 #ifdef CONFIG_BFIN_SIR0
1949         &bfin_sir0_device,
1950 #endif
1951 #ifdef CONFIG_BFIN_SIR1
1952         &bfin_sir1_device,
1953 #endif
1954 #endif
1955
1956 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
1957         &i2c_bfin_twi_device,
1958 #endif
1959
1960 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1961 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1962         &bfin_sport0_uart_device,
1963 #endif
1964 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1965         &bfin_sport1_uart_device,
1966 #endif
1967 #endif
1968
1969 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
1970         &bfin_pata_device,
1971 #endif
1972
1973 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1974         &bfin_device_gpiokeys,
1975 #endif
1976
1977 #if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
1978         &bfin_async_nand_device,
1979 #endif
1980
1981 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
1982         &stamp_flash_device,
1983 #endif
1984
1985 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
1986         &bfin_i2s,
1987 #endif
1988
1989 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
1990         &bfin_tdm,
1991 #endif
1992
1993 #if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
1994         &bfin_ac97,
1995 #endif
1996 };
1997
1998 static int __init stamp_init(void)
1999 {
2000         printk(KERN_INFO "%s(): registering device resources\n", __func__);
2001         bfin_plat_nand_init();
2002         adf702x_mac_init();
2003         platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
2004         i2c_register_board_info(0, bfin_i2c_board_info,
2005                                 ARRAY_SIZE(bfin_i2c_board_info));
2006         spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
2007
2008         return 0;
2009 }
2010
2011 arch_initcall(stamp_init);
2012
2013
2014 static struct platform_device *stamp_early_devices[] __initdata = {
2015 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
2016 #ifdef CONFIG_SERIAL_BFIN_UART0
2017         &bfin_uart0_device,
2018 #endif
2019 #ifdef CONFIG_SERIAL_BFIN_UART1
2020         &bfin_uart1_device,
2021 #endif
2022 #endif
2023
2024 #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
2025 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
2026         &bfin_sport0_uart_device,
2027 #endif
2028 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
2029         &bfin_sport1_uart_device,
2030 #endif
2031 #endif
2032 };
2033
2034 void __init native_machine_early_platform_add_devices(void)
2035 {
2036         printk(KERN_INFO "register early platform devices\n");
2037         early_platform_add_devices(stamp_early_devices,
2038                 ARRAY_SIZE(stamp_early_devices));
2039 }
2040
2041 void native_machine_restart(char *cmd)
2042 {
2043         /* workaround reboot hang when booting from SPI */
2044         if ((bfin_read_SYSCR() & 0x7) == 0x3)
2045                 bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
2046 }
2047
2048 /*
2049  * Currently the MAC address is saved in Flash by U-Boot
2050  */
2051 #define FLASH_MAC       0x203f0000
2052 void bfin_get_ether_addr(char *addr)
2053 {
2054         *(u32 *)(&(addr[0])) = bfin_read32(FLASH_MAC);
2055         *(u16 *)(&(addr[4])) = bfin_read16(FLASH_MAC + 4);
2056 }
2057 EXPORT_SYMBOL(bfin_get_ether_addr);