arch/arm/mach-omap2/pm34xx.c

   1 /*
   2  * OMAP3 Power Management Routines
   3  *
   4  * Copyright (C) 2006-2008 Nokia Corporation
   5  * Tony Lindgren <tony@atomide.com>
   6  * Jouni Hogander
   7  *
   8  * Copyright (C) 2007 Texas Instruments, Inc.
   9  * Rajendra Nayak <rnayak@ti.com>
  10  *
  11  * Copyright (C) 2005 Texas Instruments, Inc.
  12  * Richard Woodruff <r-woodruff2@ti.com>
  13  *
  14  * Based on pm.c for omap1
  15  *
  16  * This program is free software; you can redistribute it and/or modify
  17  * it under the terms of the GNU General Public License version 2 as
  18  * published by the Free Software Foundation.
  19  */
  20
  21 #include <linux/pm.h>
  22 #include <linux/suspend.h>
  23 #include <linux/interrupt.h>
  24 #include <linux/module.h>
  25 #include <linux/list.h>
  26 #include <linux/err.h>
  27 #include <linux/gpio.h>
  28 #include <linux/clk.h>
  29 #include <linux/delay.h>
  30 #include <linux/slab.h>
  31
  32 #include <plat/sram.h>
  33 #include <plat/clockdomain.h>
  34 #include <plat/powerdomain.h>
  35 #include <plat/control.h>
  36 #include <plat/serial.h>
  37 #include <plat/sdrc.h>
  38 #include <plat/prcm.h>
  39 #include <plat/gpmc.h>
  40 #include <plat/dma.h>
  41
  42 #include <asm/tlbflush.h>
  43
  44 #include "cm.h"
  45 #include "cm-regbits-34xx.h"
  46 #include "prm-regbits-34xx.h"
  47
  48 #include "prm.h"
  49 #include "pm.h"
  50 #include "sdrc.h"
  51
  52 /* Scratchpad offsets */
  53 #define OMAP343X_TABLE_ADDRESS_OFFSET      0x31
  54 #define OMAP343X_TABLE_VALUE_OFFSET        0x30
  55 #define OMAP343X_CONTROL_REG_VALUE_OFFSET  0x32
  56
  57 struct power_state {
  58         struct powerdomain *pwrdm;
  59         u32 next_state;
  60 #ifdef CONFIG_SUSPEND
  61         u32 saved_state;
  62 #endif
  63         struct list_head node;
  64 };
  65
  66 static LIST_HEAD(pwrst_list);
  67
  68 static void (*_omap_sram_idle)(u32 *addr, int save_state);
  69
  70 static int (*_omap_save_secure_sram)(u32 *addr);
  71
  72 static struct powerdomain *mpu_pwrdm, *neon_pwrdm;
  73 static struct powerdomain *core_pwrdm, *per_pwrdm;
  74 static struct powerdomain *cam_pwrdm;
  75
  76 static inline void omap3_per_save_context(void)
  77 {
  78         omap_gpio_save_context();
  79 }
  80
  81 static inline void omap3_per_restore_context(void)
  82 {
  83         omap_gpio_restore_context();
  84 }
  85
  86 static void omap3_enable_io_chain(void)
  87 {
  88         int timeout = 0;
  89
  90         if (omap_rev() >= OMAP3430_REV_ES3_1) {
  91                 prm_set_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
  92                                      PM_WKEN);
  93                 /* Do a readback to assure write has been done */
  94                 prm_read_mod_reg(WKUP_MOD, PM_WKEN);
  95
  96                 while (!(prm_read_mod_reg(WKUP_MOD, PM_WKEN) &
  97                          OMAP3430_ST_IO_CHAIN_MASK)) {
  98                         timeout++;
  99                         if (timeout > 1000) {
 100                                 printk(KERN_ERR "Wake up daisy chain "
 101                                        "activation failed.\n");
 102                                 return;
 103                         }
 104                         prm_set_mod_reg_bits(OMAP3430_ST_IO_CHAIN_MASK,
 105                                              WKUP_MOD, PM_WKEN);
 106                 }
 107         }
 108 }
 109
 110 static void omap3_disable_io_chain(void)
 111 {
 112         if (omap_rev() >= OMAP3430_REV_ES3_1)
 113                 prm_clear_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
 114                                        PM_WKEN);
 115 }
 116
 117 static void omap3_core_save_context(void)
 118 {
 119         u32 control_padconf_off;
 120
 121         /* Save the padconf registers */
 122         control_padconf_off = omap_ctrl_readl(OMAP343X_CONTROL_PADCONF_OFF);
 123         control_padconf_off |= START_PADCONF_SAVE;
 124         omap_ctrl_writel(control_padconf_off, OMAP343X_CONTROL_PADCONF_OFF);
 125         /* wait for the save to complete */
 126         while (!(omap_ctrl_readl(OMAP343X_CONTROL_GENERAL_PURPOSE_STATUS)
 127                         & PADCONF_SAVE_DONE))
 128                 udelay(1);
 129
 130         /*
 131          * Force write last pad into memory, as this can fail in some
 132          * cases according to erratas 1.157, 1.185
 133          */
 134         omap_ctrl_writel(omap_ctrl_readl(OMAP343X_PADCONF_ETK_D14),
 135                 OMAP343X_CONTROL_MEM_WKUP + 0x2a0);
 136
 137         /* Save the Interrupt controller context */
 138         omap_intc_save_context();
 139         /* Save the GPMC context */
 140         omap3_gpmc_save_context();
 141         /* Save the system control module context, padconf already save above*/
 142         omap3_control_save_context();
 143         omap_dma_global_context_save();
 144 }
 145
 146 static void omap3_core_restore_context(void)
 147 {
 148         /* Restore the control module context, padconf restored by h/w */
 149         omap3_control_restore_context();
 150         /* Restore the GPMC context */
 151         omap3_gpmc_restore_context();
 152         /* Restore the interrupt controller context */
 153         omap_intc_restore_context();
 154         omap_dma_global_context_restore();
 155 }
 156
 157 /*
 158  * FIXME: This function should be called before entering off-mode after
 159  * OMAP3 secure services have been accessed. Currently it is only called
 160  * once during boot sequence, but this works as we are not using secure
 161  * services.
 162  */
 163 static void omap3_save_secure_ram_context(u32 target_mpu_state)
 164 {
 165         u32 ret;
 166
 167         if (omap_type() != OMAP2_DEVICE_TYPE_GP) {
 168                 /*
 169                  * MPU next state must be set to POWER_ON temporarily,
 170                  * otherwise the WFI executed inside the ROM code
 171                  * will hang the system.
 172                  */
 173                 pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
 174                 ret = _omap_save_secure_sram((u32 *)
 175                                 __pa(omap3_secure_ram_storage));
 176                 pwrdm_set_next_pwrst(mpu_pwrdm, target_mpu_state);
 177                 /* Following is for error tracking, it should not happen */
 178                 if (ret) {
 179                         printk(KERN_ERR "save_secure_sram() returns %08x\n",
 180                                 ret);
 181                         while (1)
 182                                 ;
 183                 }
 184         }
 185 }
 186
 187 /*
 188  * PRCM Interrupt Handler Helper Function
 189  *
 190  * The purpose of this function is to clear any wake-up events latched
 191  * in the PRCM PM_WKST_x registers. It is possible that a wake-up event
 192  * may occur whilst attempting to clear a PM_WKST_x register and thus
 193  * set another bit in this register. A while loop is used to ensure
 194  * that any peripheral wake-up events occurring while attempting to
 195  * clear the PM_WKST_x are detected and cleared.
 196  */
 197 static int prcm_clear_mod_irqs(s16 module, u8 regs)
 198 {
 199         u32 wkst, fclk, iclk, clken;
 200         u16 wkst_off = (regs == 3) ? OMAP3430ES2_PM_WKST3 : PM_WKST1;
 201         u16 fclk_off = (regs == 3) ? OMAP3430ES2_CM_FCLKEN3 : CM_FCLKEN1;
 202         u16 iclk_off = (regs == 3) ? CM_ICLKEN3 : CM_ICLKEN1;
 203         u16 grpsel_off = (regs == 3) ?
 204                 OMAP3430ES2_PM_MPUGRPSEL3 : OMAP3430_PM_MPUGRPSEL;
 205         int c = 0;
 206
 207         wkst = prm_read_mod_reg(module, wkst_off);
 208         wkst &= prm_read_mod_reg(module, grpsel_off);
 209         if (wkst) {
 210                 iclk = cm_read_mod_reg(module, iclk_off);
 211                 fclk = cm_read_mod_reg(module, fclk_off);
 212                 while (wkst) {
 213                         clken = wkst;
 214                         cm_set_mod_reg_bits(clken, module, iclk_off);
 215                         /*
 216                          * For USBHOST, we don't know whether HOST1 or
 217                          * HOST2 woke us up, so enable both f-clocks
 218                          */
 219                         if (module == OMAP3430ES2_USBHOST_MOD)
 220                                 clken |= 1 << OMAP3430ES2_EN_USBHOST2_SHIFT;
 221                         cm_set_mod_reg_bits(clken, module, fclk_off);
 222                         prm_write_mod_reg(wkst, module, wkst_off);
 223                         wkst = prm_read_mod_reg(module, wkst_off);
 224                         c++;
 225                 }
 226                 cm_write_mod_reg(iclk, module, iclk_off);
 227                 cm_write_mod_reg(fclk, module, fclk_off);
 228         }
 229
 230         return c;
 231 }
 232
 233 static int _prcm_int_handle_wakeup(void)
 234 {
 235         int c;
 236
 237         c = prcm_clear_mod_irqs(WKUP_MOD, 1);
 238         c += prcm_clear_mod_irqs(CORE_MOD, 1);
 239         c += prcm_clear_mod_irqs(OMAP3430_PER_MOD, 1);
 240         if (omap_rev() > OMAP3430_REV_ES1_0) {
 241                 c += prcm_clear_mod_irqs(CORE_MOD, 3);
 242                 c += prcm_clear_mod_irqs(OMAP3430ES2_USBHOST_MOD, 1);
 243         }
 244
 245         return c;
 246 }
 247
 248 /*
 249  * PRCM Interrupt Handler
 250  *
 251  * The PRM_IRQSTATUS_MPU register indicates if there are any pending
 252  * interrupts from the PRCM for the MPU. These bits must be cleared in
 253  * order to clear the PRCM interrupt. The PRCM interrupt handler is
 254  * implemented to simply clear the PRM_IRQSTATUS_MPU in order to clear
 255  * the PRCM interrupt. Please note that bit 0 of the PRM_IRQSTATUS_MPU
 256  * register indicates that a wake-up event is pending for the MPU and
 257  * this bit can only be cleared if the all the wake-up events latched
 258  * in the various PM_WKST_x registers have been cleared. The interrupt
 259  * handler is implemented using a do-while loop so that if a wake-up
 260  * event occurred during the processing of the prcm interrupt handler
 261  * (setting a bit in the corresponding PM_WKST_x register and thus
 262  * preventing us from clearing bit 0 of the PRM_IRQSTATUS_MPU register)
 263  * this would be handled.
 264  */
 265 static irqreturn_t prcm_interrupt_handler (int irq, void *dev_id)
 266 {
 267         u32 irqenable_mpu, irqstatus_mpu;
 268         int c = 0;
 269
 270         irqenable_mpu = prm_read_mod_reg(OCP_MOD,
 271                                          OMAP3_PRM_IRQENABLE_MPU_OFFSET);
 272         irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
 273                                          OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 274         irqstatus_mpu &= irqenable_mpu;
 275
 276         do {
 277                 if (irqstatus_mpu & (OMAP3430_WKUP_ST_MASK |
 278                                      OMAP3430_IO_ST_MASK)) {
 279                         c = _prcm_int_handle_wakeup();
 280
 281                         /*
 282                          * Is the MPU PRCM interrupt handler racing with the
 283                          * IVA2 PRCM interrupt handler ?
 284                          */
 285                         WARN(c == 0, "prcm: WARNING: PRCM indicated MPU wakeup "
 286                              "but no wakeup sources are marked\n");
 287                 } else {
 288                         /* XXX we need to expand our PRCM interrupt handler */
 289                         WARN(1, "prcm: WARNING: PRCM interrupt received, but "
 290                              "no code to handle it (%08x)\n", irqstatus_mpu);
 291                 }
 292
 293                 prm_write_mod_reg(irqstatus_mpu, OCP_MOD,
 294                                         OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 295
 296                 irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
 297                                         OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 298                 irqstatus_mpu &= irqenable_mpu;
 299
 300         } while (irqstatus_mpu);
 301
 302         return IRQ_HANDLED;
 303 }
 304
 305 static void restore_control_register(u32 val)
 306 {
 307         __asm__ __volatile__ ("mcr p15, 0, %0, c1, c0, 0" : : "r" (val));
 308 }
 309
 310 /* Function to restore the table entry that was modified for enabling MMU */
 311 static void restore_table_entry(void)
 312 {
 313         u32 *scratchpad_address;
 314         u32 previous_value, control_reg_value;
 315         u32 *address;
 316
 317         scratchpad_address = OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD);
 318
 319         /* Get address of entry that was modified */
 320         address = (u32 *)__raw_readl(scratchpad_address +
 321                                      OMAP343X_TABLE_ADDRESS_OFFSET);
 322         /* Get the previous value which needs to be restored */
 323         previous_value = __raw_readl(scratchpad_address +
 324                                      OMAP343X_TABLE_VALUE_OFFSET);
 325         address = __va(address);
 326         *address = previous_value;
 327         flush_tlb_all();
 328         control_reg_value = __raw_readl(scratchpad_address
 329                                         + OMAP343X_CONTROL_REG_VALUE_OFFSET);
 330         /* This will enable caches and prediction */
 331         restore_control_register(control_reg_value);
 332 }
 333
 334 void omap_sram_idle(void)
 335 {
 336         /* Variable to tell what needs to be saved and restored
 337          * in omap_sram_idle*/
 338         /* save_state = 0 => Nothing to save and restored */
 339         /* save_state = 1 => Only L1 and logic lost */
 340         /* save_state = 2 => Only L2 lost */
 341         /* save_state = 3 => L1, L2 and logic lost */
 342         int save_state = 0;
 343         int mpu_next_state = PWRDM_POWER_ON;
 344         int per_next_state = PWRDM_POWER_ON;
 345         int core_next_state = PWRDM_POWER_ON;
 346         int core_prev_state, per_prev_state;
 347         u32 sdrc_pwr = 0;
 348
 349         if (!_omap_sram_idle)
 350                 return;
 351
 352         pwrdm_clear_all_prev_pwrst(mpu_pwrdm);
 353         pwrdm_clear_all_prev_pwrst(neon_pwrdm);
 354         pwrdm_clear_all_prev_pwrst(core_pwrdm);
 355         pwrdm_clear_all_prev_pwrst(per_pwrdm);
 356
 357         mpu_next_state = pwrdm_read_next_pwrst(mpu_pwrdm);
 358         switch (mpu_next_state) {
 359         case PWRDM_POWER_ON:
 360         case PWRDM_POWER_RET:
 361                 /* No need to save context */
 362                 save_state = 0;
 363                 break;
 364         case PWRDM_POWER_OFF:
 365                 save_state = 3;
 366                 break;
 367         default:
 368                 /* Invalid state */
 369                 printk(KERN_ERR "Invalid mpu state in sram_idle\n");
 370                 return;
 371         }
 372         pwrdm_pre_transition();
 373
 374         /* NEON control */
 375         if (pwrdm_read_pwrst(neon_pwrdm) == PWRDM_POWER_ON)
 376                 pwrdm_set_next_pwrst(neon_pwrdm, mpu_next_state);
 377
 378         /* Enable IO-PAD and IO-CHAIN wakeups */
 379         per_next_state = pwrdm_read_next_pwrst(per_pwrdm);
 380         core_next_state = pwrdm_read_next_pwrst(core_pwrdm);
 381         if (omap3_has_io_wakeup() &&
 382             (per_next_state < PWRDM_POWER_ON ||
 383              core_next_state < PWRDM_POWER_ON)) {
 384                 prm_set_mod_reg_bits(OMAP3430_EN_IO_MASK, WKUP_MOD, PM_WKEN);
 385                 omap3_enable_io_chain();
 386         }
 387
 388         /* PER */
 389         if (per_next_state < PWRDM_POWER_ON) {
 390                 omap_uart_prepare_idle(2);
 391                 omap2_gpio_prepare_for_idle(per_next_state);
 392                 if (per_next_state == PWRDM_POWER_OFF)
 393                                 omap3_per_save_context();
 394         }
 395
 396         /* CORE */
 397         if (core_next_state < PWRDM_POWER_ON) {
 398                 omap_uart_prepare_idle(0);
 399                 omap_uart_prepare_idle(1);
 400                 if (core_next_state == PWRDM_POWER_OFF) {
 401                         omap3_core_save_context();
 402                         omap3_prcm_save_context();
 403                 }
 404         }
 405
 406         omap3_intc_prepare_idle();
 407
 408         /*
 409         * On EMU/HS devices ROM code restores a SRDC value
 410         * from scratchpad which has automatic self refresh on timeout
 411         * of AUTO_CNT = 1 enabled. This takes care of errata 1.142.
 412         * Hence store/restore the SDRC_POWER register here.
 413         */
 414         if (omap_rev() >= OMAP3430_REV_ES3_0 &&
 415             omap_type() != OMAP2_DEVICE_TYPE_GP &&
 416             core_next_state == PWRDM_POWER_OFF)
 417                 sdrc_pwr = sdrc_read_reg(SDRC_POWER);
 418
 419         /*
 420          * omap3_arm_context is the location where ARM registers
 421          * get saved. The restore path then reads from this
 422          * location and restores them back.
 423          */
 424         _omap_sram_idle(omap3_arm_context, save_state);
 425         cpu_init();
 426
 427         /* Restore normal SDRC POWER settings */
 428         if (omap_rev() >= OMAP3430_REV_ES3_0 &&
 429             omap_type() != OMAP2_DEVICE_TYPE_GP &&
 430             core_next_state == PWRDM_POWER_OFF)
 431                 sdrc_write_reg(sdrc_pwr, SDRC_POWER);
 432
 433         /* Restore table entry modified during MMU restoration */
 434         if (pwrdm_read_prev_pwrst(mpu_pwrdm) == PWRDM_POWER_OFF)
 435                 restore_table_entry();
 436
 437         /* CORE */
 438         if (core_next_state < PWRDM_POWER_ON) {
 439                 core_prev_state = pwrdm_read_prev_pwrst(core_pwrdm);
 440                 if (core_prev_state == PWRDM_POWER_OFF) {
 441                         omap3_core_restore_context();
 442                         omap3_prcm_restore_context();
 443                         omap3_sram_restore_context();
 444                         omap2_sms_restore_context();
 445                 }
 446                 omap_uart_resume_idle(0);
 447                 omap_uart_resume_idle(1);
 448                 if (core_next_state == PWRDM_POWER_OFF)
 449                         prm_clear_mod_reg_bits(OMAP3430_AUTO_OFF_MASK,
 450                                                OMAP3430_GR_MOD,
 451                                                OMAP3_PRM_VOLTCTRL_OFFSET);
 452         }
 453         omap3_intc_resume_idle();
 454
 455         /* PER */
 456         if (per_next_state < PWRDM_POWER_ON) {
 457                 per_prev_state = pwrdm_read_prev_pwrst(per_pwrdm);
 458                 omap2_gpio_resume_after_idle();
 459                 if (per_prev_state == PWRDM_POWER_OFF)
 460                         omap3_per_restore_context();
 461                 omap_uart_resume_idle(2);
 462         }
 463
 464         /* Disable IO-PAD and IO-CHAIN wakeup */
 465         if (omap3_has_io_wakeup() &&
 466             (per_next_state < PWRDM_POWER_ON ||
 467              core_next_state < PWRDM_POWER_ON)) {
 468                 prm_clear_mod_reg_bits(OMAP3430_EN_IO_MASK, WKUP_MOD, PM_WKEN);
 469                 omap3_disable_io_chain();
 470         }
 471
 472         pwrdm_post_transition();
 473
 474         omap2_clkdm_allow_idle(mpu_pwrdm->pwrdm_clkdms[0]);
 475 }
 476
 477 int omap3_can_sleep(void)
 478 {
 479         if (!sleep_while_idle)
 480                 return 0;
 481         if (!omap_uart_can_sleep())
 482                 return 0;
 483         return 1;
 484 }
 485
 486 /* This sets pwrdm state (other than mpu & core. Currently only ON &
 487  * RET are supported. Function is assuming that clkdm doesn't have
 488  * hw_sup mode enabled. */
 489 int set_pwrdm_state(struct powerdomain *pwrdm, u32 state)
 490 {
 491         u32 cur_state;
 492         int sleep_switch = 0;
 493         int ret = 0;
 494
 495         if (pwrdm == NULL || IS_ERR(pwrdm))
 496                 return -EINVAL;
 497
 498         while (!(pwrdm->pwrsts & (1 << state))) {
 499                 if (state == PWRDM_POWER_OFF)
 500                         return ret;
 501                 state--;
 502         }
 503
 504         cur_state = pwrdm_read_next_pwrst(pwrdm);
 505         if (cur_state == state)
 506                 return ret;
 507
 508         if (pwrdm_read_pwrst(pwrdm) < PWRDM_POWER_ON) {
 509                 omap2_clkdm_wakeup(pwrdm->pwrdm_clkdms[0]);
 510                 sleep_switch = 1;
 511                 pwrdm_wait_transition(pwrdm);
 512         }
 513
 514         ret = pwrdm_set_next_pwrst(pwrdm, state);
 515         if (ret) {
 516                 printk(KERN_ERR "Unable to set state of powerdomain: %s\n",
 517                        pwrdm->name);
 518                 goto err;
 519         }
 520
 521         if (sleep_switch) {
 522                 omap2_clkdm_allow_idle(pwrdm->pwrdm_clkdms[0]);
 523                 pwrdm_wait_transition(pwrdm);
 524                 pwrdm_state_switch(pwrdm);
 525         }
 526
 527 err:
 528         return ret;
 529 }
 530
 531 static void omap3_pm_idle(void)
 532 {
 533         local_irq_disable();
 534         local_fiq_disable();
 535
 536         if (!omap3_can_sleep())
 537                 goto out;
 538
 539         if (omap_irq_pending() || need_resched())
 540                 goto out;
 541
 542         omap_sram_idle();
 543
 544 out:
 545         local_fiq_enable();
 546         local_irq_enable();
 547 }
 548
 549 #ifdef CONFIG_SUSPEND
 550 static suspend_state_t suspend_state;
 551
 552 static int omap3_pm_prepare(void)
 553 {
 554         disable_hlt();
 555         return 0;
 556 }
 557
 558 static int omap3_pm_suspend(void)
 559 {
 560         struct power_state *pwrst;
 561         int state, ret = 0;
 562
 563         if (wakeup_timer_seconds || wakeup_timer_milliseconds)
 564                 omap2_pm_wakeup_on_timer(wakeup_timer_seconds,
 565                                          wakeup_timer_milliseconds);
 566
 567         /* Read current next_pwrsts */
 568         list_for_each_entry(pwrst, &pwrst_list, node)
 569                 pwrst->saved_state = pwrdm_read_next_pwrst(pwrst->pwrdm);
 570         /* Set ones wanted by suspend */
 571         list_for_each_entry(pwrst, &pwrst_list, node) {
 572                 if (set_pwrdm_state(pwrst->pwrdm, pwrst->next_state))
 573                         goto restore;
 574                 if (pwrdm_clear_all_prev_pwrst(pwrst->pwrdm))
 575                         goto restore;
 576         }
 577
 578         omap_uart_prepare_suspend();
 579         omap3_intc_suspend();
 580
 581         omap_sram_idle();
 582
 583 restore:
 584         /* Restore next_pwrsts */
 585         list_for_each_entry(pwrst, &pwrst_list, node) {
 586                 state = pwrdm_read_prev_pwrst(pwrst->pwrdm);
 587                 if (state > pwrst->next_state) {
 588                         printk(KERN_INFO "Powerdomain (%s) didn't enter "
 589                                "target state %d\n",
 590                                pwrst->pwrdm->name, pwrst->next_state);
 591                         ret = -1;
 592                 }
 593                 set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
 594         }
 595         if (ret)
 596                 printk(KERN_ERR "Could not enter target state in pm_suspend\n");
 597         else
 598                 printk(KERN_INFO "Successfully put all powerdomains "
 599                        "to target state\n");
 600
 601         return ret;
 602 }
 603
 604 static int omap3_pm_enter(suspend_state_t unused)
 605 {
 606         int ret = 0;
 607
 608         switch (suspend_state) {
 609         case PM_SUSPEND_STANDBY:
 610         case PM_SUSPEND_MEM:
 611                 ret = omap3_pm_suspend();
 612                 break;
 613         default:
 614                 ret = -EINVAL;
 615         }
 616
 617         return ret;
 618 }
 619
 620 static void omap3_pm_finish(void)
 621 {
 622         enable_hlt();
 623 }
 624
 625 /* Hooks to enable / disable UART interrupts during suspend */
 626 static int omap3_pm_begin(suspend_state_t state)
 627 {
 628         suspend_state = state;
 629         omap_uart_enable_irqs(0);
 630         return 0;
 631 }
 632
 633 static void omap3_pm_end(void)
 634 {
 635         suspend_state = PM_SUSPEND_ON;
 636         omap_uart_enable_irqs(1);
 637         return;
 638 }
 639
 640 static struct platform_suspend_ops omap_pm_ops = {
 641         .begin          = omap3_pm_begin,
 642         .end            = omap3_pm_end,
 643         .prepare        = omap3_pm_prepare,
 644         .enter          = omap3_pm_enter,
 645         .finish         = omap3_pm_finish,
 646         .valid          = suspend_valid_only_mem,
 647 };
 648 #endif /* CONFIG_SUSPEND */
 649
 650
 651 /**
 652  * omap3_iva_idle(): ensure IVA is in idle so it can be put into
 653  *                   retention
 654  *
 655  * In cases where IVA2 is activated by bootcode, it may prevent
 656  * full-chip retention or off-mode because it is not idle.  This
 657  * function forces the IVA2 into idle state so it can go
 658  * into retention/off and thus allow full-chip retention/off.
 659  *
 660  **/
 661 static void __init omap3_iva_idle(void)
 662 {
 663         /* ensure IVA2 clock is disabled */
 664         cm_write_mod_reg(0, OMAP3430_IVA2_MOD, CM_FCLKEN);
 665
 666         /* if no clock activity, nothing else to do */
 667         if (!(cm_read_mod_reg(OMAP3430_IVA2_MOD, OMAP3430_CM_CLKSTST) &
 668               OMAP3430_CLKACTIVITY_IVA2_MASK))
 669                 return;
 670
 671         /* Reset IVA2 */
 672         prm_write_mod_reg(OMAP3430_RST1_IVA2_MASK |
 673                           OMAP3430_RST2_IVA2_MASK |
 674                           OMAP3430_RST3_IVA2_MASK,
 675                           OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL);
 676
 677         /* Enable IVA2 clock */
 678         cm_write_mod_reg(OMAP3430_CM_FCLKEN_IVA2_EN_IVA2_MASK,
 679                          OMAP3430_IVA2_MOD, CM_FCLKEN);
 680
 681         /* Set IVA2 boot mode to 'idle' */
 682         omap_ctrl_writel(OMAP3_IVA2_BOOTMOD_IDLE,
 683                          OMAP343X_CONTROL_IVA2_BOOTMOD);
 684
 685         /* Un-reset IVA2 */
 686         prm_write_mod_reg(0, OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL);
 687
 688         /* Disable IVA2 clock */
 689         cm_write_mod_reg(0, OMAP3430_IVA2_MOD, CM_FCLKEN);
 690
 691         /* Reset IVA2 */
 692         prm_write_mod_reg(OMAP3430_RST1_IVA2_MASK |
 693                           OMAP3430_RST2_IVA2_MASK |
 694                           OMAP3430_RST3_IVA2_MASK,
 695                           OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL);
 696 }
 697
 698 static void __init omap3_d2d_idle(void)
 699 {
 700         u16 mask, padconf;
 701
 702         /* In a stand alone OMAP3430 where there is not a stacked
 703          * modem for the D2D Idle Ack and D2D MStandby must be pulled
 704          * high. S CONTROL_PADCONF_SAD2D_IDLEACK and
 705          * CONTROL_PADCONF_SAD2D_MSTDBY to have a pull up. */
 706         mask = (1 << 4) | (1 << 3); /* pull-up, enabled */
 707         padconf = omap_ctrl_readw(OMAP3_PADCONF_SAD2D_MSTANDBY);
 708         padconf |= mask;
 709         omap_ctrl_writew(padconf, OMAP3_PADCONF_SAD2D_MSTANDBY);
 710
 711         padconf = omap_ctrl_readw(OMAP3_PADCONF_SAD2D_IDLEACK);
 712         padconf |= mask;
 713         omap_ctrl_writew(padconf, OMAP3_PADCONF_SAD2D_IDLEACK);
 714
 715         /* reset modem */
 716         prm_write_mod_reg(OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RSTPWRON_MASK |
 717                           OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RST_MASK,
 718                           CORE_MOD, OMAP2_RM_RSTCTRL);
 719         prm_write_mod_reg(0, CORE_MOD, OMAP2_RM_RSTCTRL);
 720 }
 721
 722 static void __init prcm_setup_regs(void)
 723 {
 724         /* XXX Reset all wkdeps. This should be done when initializing
 725          * powerdomains */
 726         prm_write_mod_reg(0, OMAP3430_IVA2_MOD, PM_WKDEP);
 727         prm_write_mod_reg(0, MPU_MOD, PM_WKDEP);
 728         prm_write_mod_reg(0, OMAP3430_DSS_MOD, PM_WKDEP);
 729         prm_write_mod_reg(0, OMAP3430_NEON_MOD, PM_WKDEP);
 730         prm_write_mod_reg(0, OMAP3430_CAM_MOD, PM_WKDEP);
 731         prm_write_mod_reg(0, OMAP3430_PER_MOD, PM_WKDEP);
 732         if (omap_rev() > OMAP3430_REV_ES1_0) {
 733                 prm_write_mod_reg(0, OMAP3430ES2_SGX_MOD, PM_WKDEP);
 734                 prm_write_mod_reg(0, OMAP3430ES2_USBHOST_MOD, PM_WKDEP);
 735         } else
 736                 prm_write_mod_reg(0, GFX_MOD, PM_WKDEP);
 737
 738         /*
 739          * Enable interface clock autoidle for all modules.
 740          * Note that in the long run this should be done by clockfw
 741          */
 742         cm_write_mod_reg(
 743                 OMAP3430_AUTO_MODEM_MASK |
 744                 OMAP3430ES2_AUTO_MMC3_MASK |
 745                 OMAP3430ES2_AUTO_ICR_MASK |
 746                 OMAP3430_AUTO_AES2_MASK |
 747                 OMAP3430_AUTO_SHA12_MASK |
 748                 OMAP3430_AUTO_DES2_MASK |
 749                 OMAP3430_AUTO_MMC2_MASK |
 750                 OMAP3430_AUTO_MMC1_MASK |
 751                 OMAP3430_AUTO_MSPRO_MASK |
 752                 OMAP3430_AUTO_HDQ_MASK |
 753                 OMAP3430_AUTO_MCSPI4_MASK |
 754                 OMAP3430_AUTO_MCSPI3_MASK |
 755                 OMAP3430_AUTO_MCSPI2_MASK |
 756                 OMAP3430_AUTO_MCSPI1_MASK |
 757                 OMAP3430_AUTO_I2C3_MASK |
 758                 OMAP3430_AUTO_I2C2_MASK |
 759                 OMAP3430_AUTO_I2C1_MASK |
 760                 OMAP3430_AUTO_UART2_MASK |
 761                 OMAP3430_AUTO_UART1_MASK |
 762                 OMAP3430_AUTO_GPT11_MASK |
 763                 OMAP3430_AUTO_GPT10_MASK |
 764                 OMAP3430_AUTO_MCBSP5_MASK |
 765                 OMAP3430_AUTO_MCBSP1_MASK |
 766                 OMAP3430ES1_AUTO_FAC_MASK | /* This is es1 only */
 767                 OMAP3430_AUTO_MAILBOXES_MASK |
 768                 OMAP3430_AUTO_OMAPCTRL_MASK |
 769                 OMAP3430ES1_AUTO_FSHOSTUSB_MASK |
 770                 OMAP3430_AUTO_HSOTGUSB_MASK |
 771                 OMAP3430_AUTO_SAD2D_MASK |
 772                 OMAP3430_AUTO_SSI_MASK,
 773                 CORE_MOD, CM_AUTOIDLE1);
 774
 775         cm_write_mod_reg(
 776                 OMAP3430_AUTO_PKA_MASK |
 777                 OMAP3430_AUTO_AES1_MASK |
 778                 OMAP3430_AUTO_RNG_MASK |
 779                 OMAP3430_AUTO_SHA11_MASK |
 780                 OMAP3430_AUTO_DES1_MASK,
 781                 CORE_MOD, CM_AUTOIDLE2);
 782
 783         if (omap_rev() > OMAP3430_REV_ES1_0) {
 784                 cm_write_mod_reg(
 785                         OMAP3430_AUTO_MAD2D_MASK |
 786                         OMAP3430ES2_AUTO_USBTLL_MASK,
 787                         CORE_MOD, CM_AUTOIDLE3);
 788         }
 789
 790         cm_write_mod_reg(
 791                 OMAP3430_AUTO_WDT2_MASK |
 792                 OMAP3430_AUTO_WDT1_MASK |
 793                 OMAP3430_AUTO_GPIO1_MASK |
 794                 OMAP3430_AUTO_32KSYNC_MASK |
 795                 OMAP3430_AUTO_GPT12_MASK |
 796                 OMAP3430_AUTO_GPT1_MASK,
 797                 WKUP_MOD, CM_AUTOIDLE);
 798
 799         cm_write_mod_reg(
 800                 OMAP3430_AUTO_DSS_MASK,
 801                 OMAP3430_DSS_MOD,
 802                 CM_AUTOIDLE);
 803
 804         cm_write_mod_reg(
 805                 OMAP3430_AUTO_CAM_MASK,
 806                 OMAP3430_CAM_MOD,
 807                 CM_AUTOIDLE);
 808
 809         cm_write_mod_reg(
 810                 OMAP3430_AUTO_GPIO6_MASK |
 811                 OMAP3430_AUTO_GPIO5_MASK |
 812                 OMAP3430_AUTO_GPIO4_MASK |
 813                 OMAP3430_AUTO_GPIO3_MASK |
 814                 OMAP3430_AUTO_GPIO2_MASK |
 815                 OMAP3430_AUTO_WDT3_MASK |
 816                 OMAP3430_AUTO_UART3_MASK |
 817                 OMAP3430_AUTO_GPT9_MASK |
 818                 OMAP3430_AUTO_GPT8_MASK |
 819                 OMAP3430_AUTO_GPT7_MASK |
 820                 OMAP3430_AUTO_GPT6_MASK |
 821                 OMAP3430_AUTO_GPT5_MASK |
 822                 OMAP3430_AUTO_GPT4_MASK |
 823                 OMAP3430_AUTO_GPT3_MASK |
 824                 OMAP3430_AUTO_GPT2_MASK |
 825                 OMAP3430_AUTO_MCBSP4_MASK |
 826                 OMAP3430_AUTO_MCBSP3_MASK |
 827                 OMAP3430_AUTO_MCBSP2_MASK,
 828                 OMAP3430_PER_MOD,
 829                 CM_AUTOIDLE);
 830
 831         if (omap_rev() > OMAP3430_REV_ES1_0) {
 832                 cm_write_mod_reg(
 833                         OMAP3430ES2_AUTO_USBHOST_MASK,
 834                         OMAP3430ES2_USBHOST_MOD,
 835                         CM_AUTOIDLE);
 836         }
 837
 838         omap_ctrl_writel(OMAP3430_AUTOIDLE_MASK, OMAP2_CONTROL_SYSCONFIG);
 839
 840         /*
 841          * Set all plls to autoidle. This is needed until autoidle is
 842          * enabled by clockfw
 843          */
 844         cm_write_mod_reg(1 << OMAP3430_AUTO_IVA2_DPLL_SHIFT,
 845                          OMAP3430_IVA2_MOD, CM_AUTOIDLE2);
 846         cm_write_mod_reg(1 << OMAP3430_AUTO_MPU_DPLL_SHIFT,
 847                          MPU_MOD,
 848                          CM_AUTOIDLE2);
 849         cm_write_mod_reg((1 << OMAP3430_AUTO_PERIPH_DPLL_SHIFT) |
 850                          (1 << OMAP3430_AUTO_CORE_DPLL_SHIFT),
 851                          PLL_MOD,
 852                          CM_AUTOIDLE);
 853         cm_write_mod_reg(1 << OMAP3430ES2_AUTO_PERIPH2_DPLL_SHIFT,
 854                          PLL_MOD,
 855                          CM_AUTOIDLE2);
 856
 857         /*
 858          * Enable control of expternal oscillator through
 859          * sys_clkreq. In the long run clock framework should
 860          * take care of this.
 861          */
 862         prm_rmw_mod_reg_bits(OMAP_AUTOEXTCLKMODE_MASK,
 863                              1 << OMAP_AUTOEXTCLKMODE_SHIFT,
 864                              OMAP3430_GR_MOD,
 865                              OMAP3_PRM_CLKSRC_CTRL_OFFSET);
 866
 867         /* setup wakup source */
 868         prm_write_mod_reg(OMAP3430_EN_IO_MASK | OMAP3430_EN_GPIO1_MASK |
 869                           OMAP3430_EN_GPT1_MASK | OMAP3430_EN_GPT12_MASK,
 870                           WKUP_MOD, PM_WKEN);
 871         /* No need to write EN_IO, that is always enabled */
 872         prm_write_mod_reg(OMAP3430_GRPSEL_GPIO1_MASK |
 873                           OMAP3430_GRPSEL_GPT1_MASK |
 874                           OMAP3430_GRPSEL_GPT12_MASK,
 875                           WKUP_MOD, OMAP3430_PM_MPUGRPSEL);
 876         /* For some reason IO doesn't generate wakeup event even if
 877          * it is selected to mpu wakeup goup */
 878         prm_write_mod_reg(OMAP3430_IO_EN_MASK | OMAP3430_WKUP_EN_MASK,
 879                           OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET);
 880
 881         /* Enable PM_WKEN to support DSS LPR */
 882         prm_write_mod_reg(OMAP3430_PM_WKEN_DSS_EN_DSS_MASK,
 883                                 OMAP3430_DSS_MOD, PM_WKEN);
 884
 885         /* Enable wakeups in PER */
 886         prm_write_mod_reg(OMAP3430_EN_GPIO2_MASK | OMAP3430_EN_GPIO3_MASK |
 887                           OMAP3430_EN_GPIO4_MASK | OMAP3430_EN_GPIO5_MASK |
 888                           OMAP3430_EN_GPIO6_MASK | OMAP3430_EN_UART3_MASK |
 889                           OMAP3430_EN_MCBSP2_MASK | OMAP3430_EN_MCBSP3_MASK |
 890                           OMAP3430_EN_MCBSP4_MASK,
 891                           OMAP3430_PER_MOD, PM_WKEN);
 892         /* and allow them to wake up MPU */
 893         prm_write_mod_reg(OMAP3430_GRPSEL_GPIO2_MASK |
 894                           OMAP3430_GRPSEL_GPIO3_MASK |
 895                           OMAP3430_GRPSEL_GPIO4_MASK |
 896                           OMAP3430_GRPSEL_GPIO5_MASK |
 897                           OMAP3430_GRPSEL_GPIO6_MASK |
 898                           OMAP3430_GRPSEL_UART3_MASK |
 899                           OMAP3430_GRPSEL_MCBSP2_MASK |
 900                           OMAP3430_GRPSEL_MCBSP3_MASK |
 901                           OMAP3430_GRPSEL_MCBSP4_MASK,
 902                           OMAP3430_PER_MOD, OMAP3430_PM_MPUGRPSEL);
 903
 904         /* Don't attach IVA interrupts */
 905         prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL);
 906         prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1);
 907         prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3);
 908         prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL);
 909
 910         /* Clear any pending 'reset' flags */
 911         prm_write_mod_reg(0xffffffff, MPU_MOD, OMAP2_RM_RSTST);
 912         prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP2_RM_RSTST);
 913         prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, OMAP2_RM_RSTST);
 914         prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, OMAP2_RM_RSTST);
 915         prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, OMAP2_RM_RSTST);
 916         prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, OMAP2_RM_RSTST);
 917         prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, OMAP2_RM_RSTST);
 918
 919         /* Clear any pending PRCM interrupts */
 920         prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 921
 922         omap3_iva_idle();
 923         omap3_d2d_idle();
 924 }
 925
 926 void omap3_pm_off_mode_enable(int enable)
 927 {
 928         struct power_state *pwrst;
 929         u32 state;
 930
 931         if (enable)
 932                 state = PWRDM_POWER_OFF;
 933         else
 934                 state = PWRDM_POWER_RET;
 935
 936 #ifdef CONFIG_CPU_IDLE
 937         omap3_cpuidle_update_states();
 938 #endif
 939
 940         list_for_each_entry(pwrst, &pwrst_list, node) {
 941                 pwrst->next_state = state;
 942                 set_pwrdm_state(pwrst->pwrdm, state);
 943         }
 944 }
 945
 946 int omap3_pm_get_suspend_state(struct powerdomain *pwrdm)
 947 {
 948         struct power_state *pwrst;
 949
 950         list_for_each_entry(pwrst, &pwrst_list, node) {
 951                 if (pwrst->pwrdm == pwrdm)
 952                         return pwrst->next_state;
 953         }
 954         return -EINVAL;
 955 }
 956
 957 int omap3_pm_set_suspend_state(struct powerdomain *pwrdm, int state)
 958 {
 959         struct power_state *pwrst;
 960
 961         list_for_each_entry(pwrst, &pwrst_list, node) {
 962                 if (pwrst->pwrdm == pwrdm) {
 963                         pwrst->next_state = state;
 964                         return 0;
 965                 }
 966         }
 967         return -EINVAL;
 968 }
 969
 970 static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused)
 971 {
 972         struct power_state *pwrst;
 973
 974         if (!pwrdm->pwrsts)
 975                 return 0;
 976
 977         pwrst = kmalloc(sizeof(struct power_state), GFP_ATOMIC);
 978         if (!pwrst)
 979                 return -ENOMEM;
 980         pwrst->pwrdm = pwrdm;
 981         pwrst->next_state = PWRDM_POWER_RET;
 982         list_add(&pwrst->node, &pwrst_list);
 983
 984         if (pwrdm_has_hdwr_sar(pwrdm))
 985                 pwrdm_enable_hdwr_sar(pwrdm);
 986
 987         return set_pwrdm_state(pwrst->pwrdm, pwrst->next_state);
 988 }
 989
 990 /*
 991  * Enable hw supervised mode for all clockdomains if it's
 992  * supported. Initiate sleep transition for other clockdomains, if
 993  * they are not used
 994  */
 995 static int __init clkdms_setup(struct clockdomain *clkdm, void *unused)
 996 {
 997         clkdm_clear_all_wkdeps(clkdm);
 998         clkdm_clear_all_sleepdeps(clkdm);
 999
1000         if (clkdm->flags & CLKDM_CAN_ENABLE_AUTO)
1001                 omap2_clkdm_allow_idle(clkdm);
1002         else if (clkdm->flags & CLKDM_CAN_FORCE_SLEEP &&
1003                  atomic_read(&clkdm->usecount) == 0)
1004                 omap2_clkdm_sleep(clkdm);
1005         return 0;
1006 }
1007
1008 void omap_push_sram_idle(void)
1009 {
1010         _omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend,
1011                                         omap34xx_cpu_suspend_sz);
1012         if (omap_type() != OMAP2_DEVICE_TYPE_GP)
1013                 _omap_save_secure_sram = omap_sram_push(save_secure_ram_context,
1014                                 save_secure_ram_context_sz);
1015 }
1016
1017 static int __init omap3_pm_init(void)
1018 {
1019         struct power_state *pwrst, *tmp;
1020         struct clockdomain *neon_clkdm, *per_clkdm, *mpu_clkdm, *core_clkdm;
1021         int ret;
1022
1023         if (!cpu_is_omap34xx())
1024                 return -ENODEV;
1025
1026         printk(KERN_ERR "Power Management for TI OMAP3.\n");
1027
1028         /* XXX prcm_setup_regs needs to be before enabling hw
1029          * supervised mode for powerdomains */
1030         prcm_setup_regs();
1031
1032         ret = request_irq(INT_34XX_PRCM_MPU_IRQ,
1033                           (irq_handler_t)prcm_interrupt_handler,
1034                           IRQF_DISABLED, "prcm", NULL);
1035         if (ret) {
1036                 printk(KERN_ERR "request_irq failed to register for 0x%x\n",
1037                        INT_34XX_PRCM_MPU_IRQ);
1038                 goto err1;
1039         }
1040
1041         ret = pwrdm_for_each(pwrdms_setup, NULL);
1042         if (ret) {
1043                 printk(KERN_ERR "Failed to setup powerdomains\n");
1044                 goto err2;
1045         }
1046
1047         (void) clkdm_for_each(clkdms_setup, NULL);
1048
1049         mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
1050         if (mpu_pwrdm == NULL) {
1051                 printk(KERN_ERR "Failed to get mpu_pwrdm\n");
1052                 goto err2;
1053         }
1054
1055         neon_pwrdm = pwrdm_lookup("neon_pwrdm");
1056         per_pwrdm = pwrdm_lookup("per_pwrdm");
1057         core_pwrdm = pwrdm_lookup("core_pwrdm");
1058         cam_pwrdm = pwrdm_lookup("cam_pwrdm");
1059
1060         neon_clkdm = clkdm_lookup("neon_clkdm");
1061         mpu_clkdm = clkdm_lookup("mpu_clkdm");
1062         per_clkdm = clkdm_lookup("per_clkdm");
1063         core_clkdm = clkdm_lookup("core_clkdm");
1064
1065         omap_push_sram_idle();
1066 #ifdef CONFIG_SUSPEND
1067         suspend_set_ops(&omap_pm_ops);
1068 #endif /* CONFIG_SUSPEND */
1069
1070         pm_idle = omap3_pm_idle;
1071         omap3_idle_init();
1072
1073         clkdm_add_wkdep(neon_clkdm, mpu_clkdm);
1074         if (omap_type() != OMAP2_DEVICE_TYPE_GP) {
1075                 omap3_secure_ram_storage =
1076                         kmalloc(0x803F, GFP_KERNEL);
1077                 if (!omap3_secure_ram_storage)
1078                         printk(KERN_ERR "Memory allocation failed when"
1079                                         "allocating for secure sram context\n");
1080
1081                 local_irq_disable();
1082                 local_fiq_disable();
1083
1084                 omap_dma_global_context_save();
1085                 omap3_save_secure_ram_context(PWRDM_POWER_ON);
1086                 omap_dma_global_context_restore();
1087
1088                 local_irq_enable();
1089                 local_fiq_enable();
1090         }
1091
1092         omap3_save_scratchpad_contents();
1093 err1:
1094         return ret;
1095 err2:
1096         free_irq(INT_34XX_PRCM_MPU_IRQ, NULL);
1097         list_for_each_entry_safe(pwrst, tmp, &pwrst_list, node) {
1098                 list_del(&pwrst->node);
1099                 kfree(pwrst);
1100         }
1101         return ret;
1102 }
1103
1104 late_initcall(omap3_pm_init);