2 * TI DA830/OMAP L137 EVM board
4 * Author: Mark A. Greer <mgreer@mvista.com>
5 * Derived from: arch/arm/mach-davinci/board-dm644x-evm.c
7 * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
8 * the terms of the GNU General Public License version 2. This program
9 * is licensed "as is" without any warranty of any kind, whether express
12 #include <linux/kernel.h>
13 #include <linux/init.h>
14 #include <linux/console.h>
15 #include <linux/interrupt.h>
16 #include <linux/gpio.h>
17 #include <linux/platform_device.h>
18 #include <linux/i2c.h>
19 #include <linux/i2c/pcf857x.h>
20 #include <linux/i2c/at24.h>
21 #include <linux/mtd/mtd.h>
22 #include <linux/mtd/partitions.h>
24 #include <asm/mach-types.h>
25 #include <asm/mach/arch.h>
27 #include <mach/cp_intc.h>
29 #include <mach/nand.h>
30 #include <mach/da8xx.h>
32 #include <mach/aemif.h>
34 #define DA830_EVM_PHY_MASK 0x0
35 #define DA830_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
38 * USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4].
40 #define ON_BD_USB_DRV GPIO_TO_PIN(1, 15)
41 #define ON_BD_USB_OVC GPIO_TO_PIN(2, 4)
43 static const short da830_evm_usb11_pins[] = {
44 DA830_GPIO1_15, DA830_GPIO2_4,
48 static da8xx_ocic_handler_t da830_evm_usb_ocic_handler;
50 static int da830_evm_usb_set_power(unsigned port, int on)
52 gpio_set_value(ON_BD_USB_DRV, on);
56 static int da830_evm_usb_get_power(unsigned port)
58 return gpio_get_value(ON_BD_USB_DRV);
61 static int da830_evm_usb_get_oci(unsigned port)
63 return !gpio_get_value(ON_BD_USB_OVC);
66 static irqreturn_t da830_evm_usb_ocic_irq(int, void *);
68 static int da830_evm_usb_ocic_notify(da8xx_ocic_handler_t handler)
70 int irq = gpio_to_irq(ON_BD_USB_OVC);
73 if (handler != NULL) {
74 da830_evm_usb_ocic_handler = handler;
76 error = request_irq(irq, da830_evm_usb_ocic_irq, IRQF_DISABLED |
77 IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
78 "OHCI over-current indicator", NULL);
80 printk(KERN_ERR "%s: could not request IRQ to watch "
81 "over-current indicator changes\n", __func__);
88 static struct da8xx_ohci_root_hub da830_evm_usb11_pdata = {
89 .set_power = da830_evm_usb_set_power,
90 .get_power = da830_evm_usb_get_power,
91 .get_oci = da830_evm_usb_get_oci,
92 .ocic_notify = da830_evm_usb_ocic_notify,
94 /* TPS2065 switch @ 5V */
95 .potpgt = (3 + 1) / 2, /* 3 ms max */
98 static irqreturn_t da830_evm_usb_ocic_irq(int irq, void *dev_id)
100 da830_evm_usb_ocic_handler(&da830_evm_usb11_pdata, 1);
104 static __init void da830_evm_usb_init(void)
110 * Set up USB clock/mode in the CFGCHIP2 register.
111 * FYI: CFGCHIP2 is 0x0000ef00 initially.
113 cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
115 /* USB2.0 PHY reference clock is 24 MHz */
116 cfgchip2 &= ~CFGCHIP2_REFFREQ;
117 cfgchip2 |= CFGCHIP2_REFFREQ_24MHZ;
120 * Select internal reference clock for USB 2.0 PHY
121 * and use it as a clock source for USB 1.1 PHY
122 * (this is the default setting anyway).
124 cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX;
125 cfgchip2 |= CFGCHIP2_USB2PHYCLKMUX;
128 * We have to override VBUS/ID signals when MUSB is configured into the
129 * host-only mode -- ID pin will float if no cable is connected, so the
130 * controller won't be able to drive VBUS thinking that it's a B-device.
131 * Otherwise, we want to use the OTG mode and enable VBUS comparators.
133 cfgchip2 &= ~CFGCHIP2_OTGMODE;
134 #ifdef CONFIG_USB_MUSB_HOST
135 cfgchip2 |= CFGCHIP2_FORCE_HOST;
137 cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN;
140 __raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
142 /* USB_REFCLKIN is not used. */
143 ret = davinci_cfg_reg(DA830_USB0_DRVVBUS);
145 pr_warning("%s: USB 2.0 PinMux setup failed: %d\n",
149 * TPS2065 switch @ 5V supplies 1 A (sustains 1.5 A),
150 * with the power on to power good time of 3 ms.
152 ret = da8xx_register_usb20(1000, 3);
154 pr_warning("%s: USB 2.0 registration failed: %d\n",
158 ret = davinci_cfg_reg_list(da830_evm_usb11_pins);
160 pr_warning("%s: USB 1.1 PinMux setup failed: %d\n",
165 ret = gpio_request(ON_BD_USB_DRV, "ON_BD_USB_DRV");
167 printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port "
168 "power control: %d\n", __func__, ret);
171 gpio_direction_output(ON_BD_USB_DRV, 0);
173 ret = gpio_request(ON_BD_USB_OVC, "ON_BD_USB_OVC");
175 printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port "
176 "over-current indicator: %d\n", __func__, ret);
179 gpio_direction_input(ON_BD_USB_OVC);
181 ret = da8xx_register_usb11(&da830_evm_usb11_pdata);
183 pr_warning("%s: USB 1.1 registration failed: %d\n",
187 static struct davinci_uart_config da830_evm_uart_config __initdata = {
188 .enabled_uarts = 0x7,
191 static const short da830_evm_mcasp1_pins[] = {
192 DA830_AHCLKX1, DA830_ACLKX1, DA830_AFSX1, DA830_AHCLKR1, DA830_AFSR1,
193 DA830_AMUTE1, DA830_AXR1_0, DA830_AXR1_1, DA830_AXR1_2, DA830_AXR1_5,
194 DA830_ACLKR1, DA830_AXR1_6, DA830_AXR1_7, DA830_AXR1_8, DA830_AXR1_10,
199 static u8 da830_iis_serializer_direction[] = {
200 RX_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
201 INACTIVE_MODE, TX_MODE, INACTIVE_MODE, INACTIVE_MODE,
202 INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
205 static struct snd_platform_data da830_evm_snd_data = {
206 .tx_dma_offset = 0x2000,
207 .rx_dma_offset = 0x2000,
208 .op_mode = DAVINCI_MCASP_IIS_MODE,
209 .num_serializer = ARRAY_SIZE(da830_iis_serializer_direction),
211 .serial_dir = da830_iis_serializer_direction,
212 .asp_chan_q = EVENTQ_0,
213 .version = MCASP_VERSION_2,
219 * GPIO2[1] is used as MMC_SD_WP and GPIO2[2] as MMC_SD_INS.
221 static const short da830_evm_mmc_sd_pins[] = {
222 DA830_MMCSD_DAT_0, DA830_MMCSD_DAT_1, DA830_MMCSD_DAT_2,
223 DA830_MMCSD_DAT_3, DA830_MMCSD_DAT_4, DA830_MMCSD_DAT_5,
224 DA830_MMCSD_DAT_6, DA830_MMCSD_DAT_7, DA830_MMCSD_CLK,
225 DA830_MMCSD_CMD, DA830_GPIO2_1, DA830_GPIO2_2,
229 #define DA830_MMCSD_WP_PIN GPIO_TO_PIN(2, 1)
230 #define DA830_MMCSD_CD_PIN GPIO_TO_PIN(2, 2)
232 static int da830_evm_mmc_get_ro(int index)
234 return gpio_get_value(DA830_MMCSD_WP_PIN);
237 static int da830_evm_mmc_get_cd(int index)
239 return !gpio_get_value(DA830_MMCSD_CD_PIN);
242 static struct davinci_mmc_config da830_evm_mmc_config = {
243 .get_ro = da830_evm_mmc_get_ro,
244 .get_cd = da830_evm_mmc_get_cd,
246 .max_freq = 50000000,
247 .caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
248 .version = MMC_CTLR_VERSION_2,
251 static inline void da830_evm_init_mmc(void)
255 ret = davinci_cfg_reg_list(da830_evm_mmc_sd_pins);
257 pr_warning("da830_evm_init: mmc/sd mux setup failed: %d\n",
262 ret = gpio_request(DA830_MMCSD_WP_PIN, "MMC WP");
264 pr_warning("da830_evm_init: can not open GPIO %d\n",
268 gpio_direction_input(DA830_MMCSD_WP_PIN);
270 ret = gpio_request(DA830_MMCSD_CD_PIN, "MMC CD\n");
272 pr_warning("da830_evm_init: can not open GPIO %d\n",
276 gpio_direction_input(DA830_MMCSD_CD_PIN);
278 ret = da8xx_register_mmcsd0(&da830_evm_mmc_config);
280 pr_warning("da830_evm_init: mmc/sd registration failed: %d\n",
282 gpio_free(DA830_MMCSD_WP_PIN);
287 * UI board NAND/NOR flashes only use 8-bit data bus.
289 static const short da830_evm_emif25_pins[] = {
290 DA830_EMA_D_0, DA830_EMA_D_1, DA830_EMA_D_2, DA830_EMA_D_3,
291 DA830_EMA_D_4, DA830_EMA_D_5, DA830_EMA_D_6, DA830_EMA_D_7,
292 DA830_EMA_A_0, DA830_EMA_A_1, DA830_EMA_A_2, DA830_EMA_A_3,
293 DA830_EMA_A_4, DA830_EMA_A_5, DA830_EMA_A_6, DA830_EMA_A_7,
294 DA830_EMA_A_8, DA830_EMA_A_9, DA830_EMA_A_10, DA830_EMA_A_11,
295 DA830_EMA_A_12, DA830_EMA_BA_0, DA830_EMA_BA_1, DA830_NEMA_WE,
296 DA830_NEMA_CS_2, DA830_NEMA_CS_3, DA830_NEMA_OE, DA830_EMA_WAIT_0,
300 #if defined(CONFIG_MMC_DAVINCI) || defined(CONFIG_MMC_DAVINCI_MODULE)
306 #ifdef CONFIG_DA830_UI_NAND
307 static struct mtd_partition da830_evm_nand_partitions[] = {
308 /* bootloader (U-Boot, etc) in first sector */
310 .name = "bootloader",
313 .mask_flags = MTD_WRITEABLE, /* force read-only */
315 /* bootloader params in the next sector */
318 .offset = MTDPART_OFS_APPEND,
320 .mask_flags = MTD_WRITEABLE, /* force read-only */
325 .offset = MTDPART_OFS_APPEND,
331 .name = "filesystem",
332 .offset = MTDPART_OFS_APPEND,
333 .size = MTDPART_SIZ_FULL,
338 /* flash bbt decriptors */
339 static uint8_t da830_evm_nand_bbt_pattern[] = { 'B', 'b', 't', '0' };
340 static uint8_t da830_evm_nand_mirror_pattern[] = { '1', 't', 'b', 'B' };
342 static struct nand_bbt_descr da830_evm_nand_bbt_main_descr = {
343 .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE |
344 NAND_BBT_WRITE | NAND_BBT_2BIT |
345 NAND_BBT_VERSION | NAND_BBT_PERCHIP,
350 .pattern = da830_evm_nand_bbt_pattern
353 static struct nand_bbt_descr da830_evm_nand_bbt_mirror_descr = {
354 .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE |
355 NAND_BBT_WRITE | NAND_BBT_2BIT |
356 NAND_BBT_VERSION | NAND_BBT_PERCHIP,
361 .pattern = da830_evm_nand_mirror_pattern
364 static struct davinci_aemif_timing da830_evm_nandflash_timing = {
374 static struct davinci_nand_pdata da830_evm_nand_pdata = {
375 .parts = da830_evm_nand_partitions,
376 .nr_parts = ARRAY_SIZE(da830_evm_nand_partitions),
377 .ecc_mode = NAND_ECC_HW,
379 .options = NAND_USE_FLASH_BBT,
380 .bbt_td = &da830_evm_nand_bbt_main_descr,
381 .bbt_md = &da830_evm_nand_bbt_mirror_descr,
382 .timing = &da830_evm_nandflash_timing,
385 static struct resource da830_evm_nand_resources[] = {
386 [0] = { /* First memory resource is NAND I/O window */
387 .start = DA8XX_AEMIF_CS3_BASE,
388 .end = DA8XX_AEMIF_CS3_BASE + PAGE_SIZE - 1,
389 .flags = IORESOURCE_MEM,
391 [1] = { /* Second memory resource is AEMIF control registers */
392 .start = DA8XX_AEMIF_CTL_BASE,
393 .end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
394 .flags = IORESOURCE_MEM,
398 static struct platform_device da830_evm_nand_device = {
399 .name = "davinci_nand",
402 .platform_data = &da830_evm_nand_pdata,
404 .num_resources = ARRAY_SIZE(da830_evm_nand_resources),
405 .resource = da830_evm_nand_resources,
408 static inline void da830_evm_init_nand(int mux_mode)
413 pr_warning("WARNING: both MMC/SD and NAND are "
414 "enabled, but they share AEMIF pins.\n"
415 "\tDisable MMC/SD for NAND support.\n");
419 ret = davinci_cfg_reg_list(da830_evm_emif25_pins);
421 pr_warning("da830_evm_init: emif25 mux setup failed: %d\n",
424 ret = platform_device_register(&da830_evm_nand_device);
426 pr_warning("da830_evm_init: NAND device not registered.\n");
428 gpio_direction_output(mux_mode, 1);
431 static inline void da830_evm_init_nand(int mux_mode) { }
434 #ifdef CONFIG_DA830_UI_LCD
435 static inline void da830_evm_init_lcdc(int mux_mode)
439 ret = davinci_cfg_reg_list(da830_lcdcntl_pins);
441 pr_warning("da830_evm_init: lcdcntl mux setup failed: %d\n",
444 ret = da8xx_register_lcdc(&sharp_lcd035q3dg01_pdata);
446 pr_warning("da830_evm_init: lcd setup failed: %d\n", ret);
448 gpio_direction_output(mux_mode, 0);
451 static inline void da830_evm_init_lcdc(int mux_mode) { }
454 static struct at24_platform_data da830_evm_i2c_eeprom_info = {
455 .byte_len = SZ_256K / 8,
457 .flags = AT24_FLAG_ADDR16,
458 .setup = davinci_get_mac_addr,
459 .context = (void *)0x7f00,
462 static int __init da830_evm_ui_expander_setup(struct i2c_client *client,
463 int gpio, unsigned ngpio, void *context)
465 gpio_request(gpio + 6, "UI MUX_MODE");
467 /* Drive mux mode low to match the default without UI card */
468 gpio_direction_output(gpio + 6, 0);
470 da830_evm_init_lcdc(gpio + 6);
472 da830_evm_init_nand(gpio + 6);
477 static int da830_evm_ui_expander_teardown(struct i2c_client *client, int gpio,
478 unsigned ngpio, void *context)
484 static struct pcf857x_platform_data __initdata da830_evm_ui_expander_info = {
485 .gpio_base = DAVINCI_N_GPIO,
486 .setup = da830_evm_ui_expander_setup,
487 .teardown = da830_evm_ui_expander_teardown,
490 static struct i2c_board_info __initdata da830_evm_i2c_devices[] = {
492 I2C_BOARD_INFO("24c256", 0x50),
493 .platform_data = &da830_evm_i2c_eeprom_info,
496 I2C_BOARD_INFO("tlv320aic3x", 0x18),
499 I2C_BOARD_INFO("pcf8574", 0x3f),
500 .platform_data = &da830_evm_ui_expander_info,
504 static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = {
505 .bus_freq = 100, /* kHz */
506 .bus_delay = 0, /* usec */
510 * The following EDMA channels/slots are not being used by drivers (for
511 * example: Timer, GPIO, UART events etc) on da830/omap-l137 EVM, hence
512 * they are being reserved for codecs on the DSP side.
514 static const s16 da830_dma_rsv_chans[][2] = {
515 /* (offset, number) */
523 static const s16 da830_dma_rsv_slots[][2] = {
524 /* (offset, number) */
532 static struct edma_rsv_info da830_edma_rsv[] = {
534 .rsv_chans = da830_dma_rsv_chans,
535 .rsv_slots = da830_dma_rsv_slots,
539 static __init void da830_evm_init(void)
541 struct davinci_soc_info *soc_info = &davinci_soc_info;
544 ret = da830_register_edma(da830_edma_rsv);
546 pr_warning("da830_evm_init: edma registration failed: %d\n",
549 ret = davinci_cfg_reg_list(da830_i2c0_pins);
551 pr_warning("da830_evm_init: i2c0 mux setup failed: %d\n",
554 ret = da8xx_register_i2c(0, &da830_evm_i2c_0_pdata);
556 pr_warning("da830_evm_init: i2c0 registration failed: %d\n",
559 da830_evm_usb_init();
561 soc_info->emac_pdata->phy_mask = DA830_EVM_PHY_MASK;
562 soc_info->emac_pdata->mdio_max_freq = DA830_EVM_MDIO_FREQUENCY;
563 soc_info->emac_pdata->rmii_en = 1;
565 ret = davinci_cfg_reg_list(da830_cpgmac_pins);
567 pr_warning("da830_evm_init: cpgmac mux setup failed: %d\n",
570 ret = da8xx_register_emac();
572 pr_warning("da830_evm_init: emac registration failed: %d\n",
575 ret = da8xx_register_watchdog();
577 pr_warning("da830_evm_init: watchdog registration failed: %d\n",
580 davinci_serial_init(&da830_evm_uart_config);
581 i2c_register_board_info(1, da830_evm_i2c_devices,
582 ARRAY_SIZE(da830_evm_i2c_devices));
584 ret = davinci_cfg_reg_list(da830_evm_mcasp1_pins);
586 pr_warning("da830_evm_init: mcasp1 mux setup failed: %d\n",
589 da8xx_register_mcasp(1, &da830_evm_snd_data);
591 da830_evm_init_mmc();
593 ret = da8xx_register_rtc();
595 pr_warning("da830_evm_init: rtc setup failed: %d\n", ret);
598 #ifdef CONFIG_SERIAL_8250_CONSOLE
599 static int __init da830_evm_console_init(void)
601 return add_preferred_console("ttyS", 2, "115200");
603 console_initcall(da830_evm_console_init);
606 static void __init da830_evm_map_io(void)
611 MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137/AM17x EVM")
613 .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
614 .boot_params = (DA8XX_DDR_BASE + 0x100),
615 .map_io = da830_evm_map_io,
616 .init_irq = cp_intc_init,
617 .timer = &davinci_timer,
618 .init_machine = da830_evm_init,