arch/arm/mach-at91/at91sam9g45_devices.c

   1 /*
   2  *  On-Chip devices setup code for the AT91SAM9G45 family
   3  *
   4  *  Copyright (C) 2009 Atmel Corporation.
   5  *
   6  * This program is free software; you can redistribute it and/or modify
   7  * it under the terms of the GNU General Public License as published by
   8  * the Free Software Foundation; either version 2 of the License, or
   9  * (at your option) any later version.
  10  *
  11  */
  12 #include <asm/mach/arch.h>
  13 #include <asm/mach/map.h>
  14
  15 #include <linux/dma-mapping.h>
  16 #include <linux/platform_device.h>
  17 #include <linux/i2c-gpio.h>
  18
  19 #include <linux/fb.h>
  20 #include <video/atmel_lcdc.h>
  21
  22 #include <mach/board.h>
  23 #include <mach/gpio.h>
  24 #include <mach/at91sam9g45.h>
  25 #include <mach/at91sam9g45_matrix.h>
  26 #include <mach/at91sam9_smc.h>
  27 #include <mach/at_hdmac.h>
  28
  29 #include "generic.h"
  30
  31
  32 /* --------------------------------------------------------------------
  33  *  HDMAC - AHB DMA Controller
  34  * -------------------------------------------------------------------- */
  35
  36 #if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE)
  37 static u64 hdmac_dmamask = DMA_BIT_MASK(32);
  38
  39 static struct at_dma_platform_data atdma_pdata = {
  40         .nr_channels    = 8,
  41 };
  42
  43 static struct resource hdmac_resources[] = {
  44         [0] = {
  45                 .start  = AT91_BASE_SYS + AT91_DMA,
  46                 .end    = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1,
  47                 .flags  = IORESOURCE_MEM,
  48         },
  49         [2] = {
  50                 .start  = AT91SAM9G45_ID_DMA,
  51                 .end    = AT91SAM9G45_ID_DMA,
  52                 .flags  = IORESOURCE_IRQ,
  53         },
  54 };
  55
  56 static struct platform_device at_hdmac_device = {
  57         .name           = "at_hdmac",
  58         .id             = -1,
  59         .dev            = {
  60                                 .dma_mask               = &hdmac_dmamask,
  61                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
  62                                 .platform_data          = &atdma_pdata,
  63         },
  64         .resource       = hdmac_resources,
  65         .num_resources  = ARRAY_SIZE(hdmac_resources),
  66 };
  67
  68 void __init at91_add_device_hdmac(void)
  69 {
  70         dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask);
  71         dma_cap_set(DMA_SLAVE, atdma_pdata.cap_mask);
  72         platform_device_register(&at_hdmac_device);
  73 }
  74 #else
  75 void __init at91_add_device_hdmac(void) {}
  76 #endif
  77
  78
  79 /* --------------------------------------------------------------------
  80  *  USB Host (OHCI)
  81  * -------------------------------------------------------------------- */
  82
  83 #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
  84 static u64 ohci_dmamask = DMA_BIT_MASK(32);
  85 static struct at91_usbh_data usbh_ohci_data;
  86
  87 static struct resource usbh_ohci_resources[] = {
  88         [0] = {
  89                 .start  = AT91SAM9G45_OHCI_BASE,
  90                 .end    = AT91SAM9G45_OHCI_BASE + SZ_1M - 1,
  91                 .flags  = IORESOURCE_MEM,
  92         },
  93         [1] = {
  94                 .start  = AT91SAM9G45_ID_UHPHS,
  95                 .end    = AT91SAM9G45_ID_UHPHS,
  96                 .flags  = IORESOURCE_IRQ,
  97         },
  98 };
  99
 100 static struct platform_device at91_usbh_ohci_device = {
 101         .name           = "at91_ohci",
 102         .id             = -1,
 103         .dev            = {
 104                                 .dma_mask               = &ohci_dmamask,
 105                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 106                                 .platform_data          = &usbh_ohci_data,
 107         },
 108         .resource       = usbh_ohci_resources,
 109         .num_resources  = ARRAY_SIZE(usbh_ohci_resources),
 110 };
 111
 112 void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data)
 113 {
 114         int i;
 115
 116         if (!data)
 117                 return;
 118
 119         /* Enable VBus control for UHP ports */
 120         for (i = 0; i < data->ports; i++) {
 121                 if (data->vbus_pin[i])
 122                         at91_set_gpio_output(data->vbus_pin[i], 0);
 123         }
 124
 125         usbh_ohci_data = *data;
 126         platform_device_register(&at91_usbh_ohci_device);
 127 }
 128 #else
 129 void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data) {}
 130 #endif
 131
 132
 133 /* --------------------------------------------------------------------
 134  *  USB Host HS (EHCI)
 135  *  Needs an OHCI host for low and full speed management
 136  * -------------------------------------------------------------------- */
 137
 138 #if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_EHCI_HCD_MODULE)
 139 static u64 ehci_dmamask = DMA_BIT_MASK(32);
 140 static struct at91_usbh_data usbh_ehci_data;
 141
 142 static struct resource usbh_ehci_resources[] = {
 143         [0] = {
 144                 .start  = AT91SAM9G45_EHCI_BASE,
 145                 .end    = AT91SAM9G45_EHCI_BASE + SZ_1M - 1,
 146                 .flags  = IORESOURCE_MEM,
 147         },
 148         [1] = {
 149                 .start  = AT91SAM9G45_ID_UHPHS,
 150                 .end    = AT91SAM9G45_ID_UHPHS,
 151                 .flags  = IORESOURCE_IRQ,
 152         },
 153 };
 154
 155 static struct platform_device at91_usbh_ehci_device = {
 156         .name           = "atmel-ehci",
 157         .id             = -1,
 158         .dev            = {
 159                                 .dma_mask               = &ehci_dmamask,
 160                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 161                                 .platform_data          = &usbh_ehci_data,
 162         },
 163         .resource       = usbh_ehci_resources,
 164         .num_resources  = ARRAY_SIZE(usbh_ehci_resources),
 165 };
 166
 167 void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data)
 168 {
 169         int i;
 170
 171         if (!data)
 172                 return;
 173
 174         /* Enable VBus control for UHP ports */
 175         for (i = 0; i < data->ports; i++) {
 176                 if (data->vbus_pin[i])
 177                         at91_set_gpio_output(data->vbus_pin[i], 0);
 178         }
 179
 180         usbh_ehci_data = *data;
 181         at91_clock_associate("uhphs_clk", &at91_usbh_ehci_device.dev, "ehci_clk");
 182         platform_device_register(&at91_usbh_ehci_device);
 183 }
 184 #else
 185 void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data) {}
 186 #endif
 187
 188
 189 /* --------------------------------------------------------------------
 190  *  USB HS Device (Gadget)
 191  * -------------------------------------------------------------------- */
 192
 193 #if defined(CONFIG_USB_GADGET_ATMEL_USBA) || defined(CONFIG_USB_GADGET_ATMEL_USBA_MODULE)
 194 static struct resource usba_udc_resources[] = {
 195         [0] = {
 196                 .start  = AT91SAM9G45_UDPHS_FIFO,
 197                 .end    = AT91SAM9G45_UDPHS_FIFO + SZ_512K - 1,
 198                 .flags  = IORESOURCE_MEM,
 199         },
 200         [1] = {
 201                 .start  = AT91SAM9G45_BASE_UDPHS,
 202                 .end    = AT91SAM9G45_BASE_UDPHS + SZ_1K - 1,
 203                 .flags  = IORESOURCE_MEM,
 204         },
 205         [2] = {
 206                 .start  = AT91SAM9G45_ID_UDPHS,
 207                 .end    = AT91SAM9G45_ID_UDPHS,
 208                 .flags  = IORESOURCE_IRQ,
 209         },
 210 };
 211
 212 #define EP(nam, idx, maxpkt, maxbk, dma, isoc)                  \
 213         [idx] = {                                               \
 214                 .name           = nam,                          \
 215                 .index          = idx,                          \
 216                 .fifo_size      = maxpkt,                       \
 217                 .nr_banks       = maxbk,                        \
 218                 .can_dma        = dma,                          \
 219                 .can_isoc       = isoc,                         \
 220         }
 221
 222 static struct usba_ep_data usba_udc_ep[] __initdata = {
 223         EP("ep0", 0, 64, 1, 0, 0),
 224         EP("ep1", 1, 1024, 2, 1, 1),
 225         EP("ep2", 2, 1024, 2, 1, 1),
 226         EP("ep3", 3, 1024, 3, 1, 0),
 227         EP("ep4", 4, 1024, 3, 1, 0),
 228         EP("ep5", 5, 1024, 3, 1, 1),
 229         EP("ep6", 6, 1024, 3, 1, 1),
 230 };
 231
 232 #undef EP
 233
 234 /*
 235  * pdata doesn't have room for any endpoints, so we need to
 236  * append room for the ones we need right after it.
 237  */
 238 static struct {
 239         struct usba_platform_data pdata;
 240         struct usba_ep_data ep[7];
 241 } usba_udc_data;
 242
 243 static struct platform_device at91_usba_udc_device = {
 244         .name           = "atmel_usba_udc",
 245         .id             = -1,
 246         .dev            = {
 247                                 .platform_data  = &usba_udc_data.pdata,
 248         },
 249         .resource       = usba_udc_resources,
 250         .num_resources  = ARRAY_SIZE(usba_udc_resources),
 251 };
 252
 253 void __init at91_add_device_usba(struct usba_platform_data *data)
 254 {
 255         usba_udc_data.pdata.vbus_pin = -EINVAL;
 256         usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep);
 257         memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep));;
 258
 259         if (data && data->vbus_pin > 0) {
 260                 at91_set_gpio_input(data->vbus_pin, 0);
 261                 at91_set_deglitch(data->vbus_pin, 1);
 262                 usba_udc_data.pdata.vbus_pin = data->vbus_pin;
 263         }
 264
 265         /* Pullup pin is handled internally by USB device peripheral */
 266
 267         /* Clocks */
 268         at91_clock_associate("utmi_clk", &at91_usba_udc_device.dev, "hclk");
 269         at91_clock_associate("udphs_clk", &at91_usba_udc_device.dev, "pclk");
 270
 271         platform_device_register(&at91_usba_udc_device);
 272 }
 273 #else
 274 void __init at91_add_device_usba(struct usba_platform_data *data) {}
 275 #endif
 276
 277
 278 /* --------------------------------------------------------------------
 279  *  Ethernet
 280  * -------------------------------------------------------------------- */
 281
 282 #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
 283 static u64 eth_dmamask = DMA_BIT_MASK(32);
 284 static struct at91_eth_data eth_data;
 285
 286 static struct resource eth_resources[] = {
 287         [0] = {
 288                 .start  = AT91SAM9G45_BASE_EMAC,
 289                 .end    = AT91SAM9G45_BASE_EMAC + SZ_16K - 1,
 290                 .flags  = IORESOURCE_MEM,
 291         },
 292         [1] = {
 293                 .start  = AT91SAM9G45_ID_EMAC,
 294                 .end    = AT91SAM9G45_ID_EMAC,
 295                 .flags  = IORESOURCE_IRQ,
 296         },
 297 };
 298
 299 static struct platform_device at91sam9g45_eth_device = {
 300         .name           = "macb",
 301         .id             = -1,
 302         .dev            = {
 303                                 .dma_mask               = &eth_dmamask,
 304                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 305                                 .platform_data          = &eth_data,
 306         },
 307         .resource       = eth_resources,
 308         .num_resources  = ARRAY_SIZE(eth_resources),
 309 };
 310
 311 void __init at91_add_device_eth(struct at91_eth_data *data)
 312 {
 313         if (!data)
 314                 return;
 315
 316         if (data->phy_irq_pin) {
 317                 at91_set_gpio_input(data->phy_irq_pin, 0);
 318                 at91_set_deglitch(data->phy_irq_pin, 1);
 319         }
 320
 321         /* Pins used for MII and RMII */
 322         at91_set_A_periph(AT91_PIN_PA17, 0);    /* ETXCK_EREFCK */
 323         at91_set_A_periph(AT91_PIN_PA15, 0);    /* ERXDV */
 324         at91_set_A_periph(AT91_PIN_PA12, 0);    /* ERX0 */
 325         at91_set_A_periph(AT91_PIN_PA13, 0);    /* ERX1 */
 326         at91_set_A_periph(AT91_PIN_PA16, 0);    /* ERXER */
 327         at91_set_A_periph(AT91_PIN_PA14, 0);    /* ETXEN */
 328         at91_set_A_periph(AT91_PIN_PA10, 0);    /* ETX0 */
 329         at91_set_A_periph(AT91_PIN_PA11, 0);    /* ETX1 */
 330         at91_set_A_periph(AT91_PIN_PA19, 0);    /* EMDIO */
 331         at91_set_A_periph(AT91_PIN_PA18, 0);    /* EMDC */
 332
 333         if (!data->is_rmii) {
 334                 at91_set_B_periph(AT91_PIN_PA29, 0);    /* ECRS */
 335                 at91_set_B_periph(AT91_PIN_PA30, 0);    /* ECOL */
 336                 at91_set_B_periph(AT91_PIN_PA8,  0);    /* ERX2 */
 337                 at91_set_B_periph(AT91_PIN_PA9,  0);    /* ERX3 */
 338                 at91_set_B_periph(AT91_PIN_PA28, 0);    /* ERXCK */
 339                 at91_set_B_periph(AT91_PIN_PA6,  0);    /* ETX2 */
 340                 at91_set_B_periph(AT91_PIN_PA7,  0);    /* ETX3 */
 341                 at91_set_B_periph(AT91_PIN_PA27, 0);    /* ETXER */
 342         }
 343
 344         eth_data = *data;
 345         platform_device_register(&at91sam9g45_eth_device);
 346 }
 347 #else
 348 void __init at91_add_device_eth(struct at91_eth_data *data) {}
 349 #endif
 350
 351
 352 /* --------------------------------------------------------------------
 353  *  NAND / SmartMedia
 354  * -------------------------------------------------------------------- */
 355
 356 #if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
 357 static struct atmel_nand_data nand_data;
 358
 359 #define NAND_BASE       AT91_CHIPSELECT_3
 360
 361 static struct resource nand_resources[] = {
 362         [0] = {
 363                 .start  = NAND_BASE,
 364                 .end    = NAND_BASE + SZ_256M - 1,
 365                 .flags  = IORESOURCE_MEM,
 366         },
 367         [1] = {
 368                 .start  = AT91_BASE_SYS + AT91_ECC,
 369                 .end    = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1,
 370                 .flags  = IORESOURCE_MEM,
 371         }
 372 };
 373
 374 static struct platform_device at91sam9g45_nand_device = {
 375         .name           = "atmel_nand",
 376         .id             = -1,
 377         .dev            = {
 378                                 .platform_data  = &nand_data,
 379         },
 380         .resource       = nand_resources,
 381         .num_resources  = ARRAY_SIZE(nand_resources),
 382 };
 383
 384 void __init at91_add_device_nand(struct atmel_nand_data *data)
 385 {
 386         unsigned long csa;
 387
 388         if (!data)
 389                 return;
 390
 391         csa = at91_sys_read(AT91_MATRIX_EBICSA);
 392         at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
 393
 394         /* enable pin */
 395         if (data->enable_pin)
 396                 at91_set_gpio_output(data->enable_pin, 1);
 397
 398         /* ready/busy pin */
 399         if (data->rdy_pin)
 400                 at91_set_gpio_input(data->rdy_pin, 1);
 401
 402         /* card detect pin */
 403         if (data->det_pin)
 404                 at91_set_gpio_input(data->det_pin, 1);
 405
 406         nand_data = *data;
 407         platform_device_register(&at91sam9g45_nand_device);
 408 }
 409 #else
 410 void __init at91_add_device_nand(struct atmel_nand_data *data) {}
 411 #endif
 412
 413
 414 /* --------------------------------------------------------------------
 415  *  TWI (i2c)
 416  * -------------------------------------------------------------------- */
 417
 418 /*
 419  * Prefer the GPIO code since the TWI controller isn't robust
 420  * (gets overruns and underruns under load) and can only issue
 421  * repeated STARTs in one scenario (the driver doesn't yet handle them).
 422  */
 423 #if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
 424 static struct i2c_gpio_platform_data pdata_i2c0 = {
 425         .sda_pin                = AT91_PIN_PA20,
 426         .sda_is_open_drain      = 1,
 427         .scl_pin                = AT91_PIN_PA21,
 428         .scl_is_open_drain      = 1,
 429         .udelay                 = 2,            /* ~100 kHz */
 430 };
 431
 432 static struct platform_device at91sam9g45_twi0_device = {
 433         .name                   = "i2c-gpio",
 434         .id                     = 0,
 435         .dev.platform_data      = &pdata_i2c0,
 436 };
 437
 438 static struct i2c_gpio_platform_data pdata_i2c1 = {
 439         .sda_pin                = AT91_PIN_PB10,
 440         .sda_is_open_drain      = 1,
 441         .scl_pin                = AT91_PIN_PB11,
 442         .scl_is_open_drain      = 1,
 443         .udelay                 = 2,            /* ~100 kHz */
 444 };
 445
 446 static struct platform_device at91sam9g45_twi1_device = {
 447         .name                   = "i2c-gpio",
 448         .id                     = 1,
 449         .dev.platform_data      = &pdata_i2c1,
 450 };
 451
 452 void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices)
 453 {
 454         i2c_register_board_info(i2c_id, devices, nr_devices);
 455
 456         if (i2c_id == 0) {
 457                 at91_set_GPIO_periph(AT91_PIN_PA20, 1);         /* TWD (SDA) */
 458                 at91_set_multi_drive(AT91_PIN_PA20, 1);
 459
 460                 at91_set_GPIO_periph(AT91_PIN_PA21, 1);         /* TWCK (SCL) */
 461                 at91_set_multi_drive(AT91_PIN_PA21, 1);
 462
 463                 platform_device_register(&at91sam9g45_twi0_device);
 464         } else {
 465                 at91_set_GPIO_periph(AT91_PIN_PB10, 1);         /* TWD (SDA) */
 466                 at91_set_multi_drive(AT91_PIN_PB10, 1);
 467
 468                 at91_set_GPIO_periph(AT91_PIN_PB11, 1);         /* TWCK (SCL) */
 469                 at91_set_multi_drive(AT91_PIN_PB11, 1);
 470
 471                 platform_device_register(&at91sam9g45_twi1_device);
 472         }
 473 }
 474
 475 #elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
 476 static struct resource twi0_resources[] = {
 477         [0] = {
 478                 .start  = AT91SAM9G45_BASE_TWI0,
 479                 .end    = AT91SAM9G45_BASE_TWI0 + SZ_16K - 1,
 480                 .flags  = IORESOURCE_MEM,
 481         },
 482         [1] = {
 483                 .start  = AT91SAM9G45_ID_TWI0,
 484                 .end    = AT91SAM9G45_ID_TWI0,
 485                 .flags  = IORESOURCE_IRQ,
 486         },
 487 };
 488
 489 static struct platform_device at91sam9g45_twi0_device = {
 490         .name           = "at91_i2c",
 491         .id             = 0,
 492         .resource       = twi0_resources,
 493         .num_resources  = ARRAY_SIZE(twi0_resources),
 494 };
 495
 496 static struct resource twi1_resources[] = {
 497         [0] = {
 498                 .start  = AT91SAM9G45_BASE_TWI1,
 499                 .end    = AT91SAM9G45_BASE_TWI1 + SZ_16K - 1,
 500                 .flags  = IORESOURCE_MEM,
 501         },
 502         [1] = {
 503                 .start  = AT91SAM9G45_ID_TWI1,
 504                 .end    = AT91SAM9G45_ID_TWI1,
 505                 .flags  = IORESOURCE_IRQ,
 506         },
 507 };
 508
 509 static struct platform_device at91sam9g45_twi1_device = {
 510         .name           = "at91_i2c",
 511         .id             = 1,
 512         .resource       = twi1_resources,
 513         .num_resources  = ARRAY_SIZE(twi1_resources),
 514 };
 515
 516 void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices)
 517 {
 518         i2c_register_board_info(i2c_id, devices, nr_devices);
 519
 520         /* pins used for TWI interface */
 521         if (i2c_id == 0) {
 522                 at91_set_A_periph(AT91_PIN_PA20, 0);            /* TWD */
 523                 at91_set_multi_drive(AT91_PIN_PA20, 1);
 524
 525                 at91_set_A_periph(AT91_PIN_PA21, 0);            /* TWCK */
 526                 at91_set_multi_drive(AT91_PIN_PA21, 1);
 527
 528                 platform_device_register(&at91sam9g45_twi0_device);
 529         } else {
 530                 at91_set_A_periph(AT91_PIN_PB10, 0);            /* TWD */
 531                 at91_set_multi_drive(AT91_PIN_PB10, 1);
 532
 533                 at91_set_A_periph(AT91_PIN_PB11, 0);            /* TWCK */
 534                 at91_set_multi_drive(AT91_PIN_PB11, 1);
 535
 536                 platform_device_register(&at91sam9g45_twi1_device);
 537         }
 538 }
 539 #else
 540 void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices) {}
 541 #endif
 542
 543
 544 /* --------------------------------------------------------------------
 545  *  SPI
 546  * -------------------------------------------------------------------- */
 547
 548 #if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
 549 static u64 spi_dmamask = DMA_BIT_MASK(32);
 550
 551 static struct resource spi0_resources[] = {
 552         [0] = {
 553                 .start  = AT91SAM9G45_BASE_SPI0,
 554                 .end    = AT91SAM9G45_BASE_SPI0 + SZ_16K - 1,
 555                 .flags  = IORESOURCE_MEM,
 556         },
 557         [1] = {
 558                 .start  = AT91SAM9G45_ID_SPI0,
 559                 .end    = AT91SAM9G45_ID_SPI0,
 560                 .flags  = IORESOURCE_IRQ,
 561         },
 562 };
 563
 564 static struct platform_device at91sam9g45_spi0_device = {
 565         .name           = "atmel_spi",
 566         .id             = 0,
 567         .dev            = {
 568                                 .dma_mask               = &spi_dmamask,
 569                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 570         },
 571         .resource       = spi0_resources,
 572         .num_resources  = ARRAY_SIZE(spi0_resources),
 573 };
 574
 575 static const unsigned spi0_standard_cs[4] = { AT91_PIN_PB3, AT91_PIN_PB18, AT91_PIN_PB19, AT91_PIN_PD27 };
 576
 577 static struct resource spi1_resources[] = {
 578         [0] = {
 579                 .start  = AT91SAM9G45_BASE_SPI1,
 580                 .end    = AT91SAM9G45_BASE_SPI1 + SZ_16K - 1,
 581                 .flags  = IORESOURCE_MEM,
 582         },
 583         [1] = {
 584                 .start  = AT91SAM9G45_ID_SPI1,
 585                 .end    = AT91SAM9G45_ID_SPI1,
 586                 .flags  = IORESOURCE_IRQ,
 587         },
 588 };
 589
 590 static struct platform_device at91sam9g45_spi1_device = {
 591         .name           = "atmel_spi",
 592         .id             = 1,
 593         .dev            = {
 594                                 .dma_mask               = &spi_dmamask,
 595                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 596         },
 597         .resource       = spi1_resources,
 598         .num_resources  = ARRAY_SIZE(spi1_resources),
 599 };
 600
 601 static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB17, AT91_PIN_PD28, AT91_PIN_PD18, AT91_PIN_PD19 };
 602
 603 void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 604 {
 605         int i;
 606         unsigned long cs_pin;
 607         short enable_spi0 = 0;
 608         short enable_spi1 = 0;
 609
 610         /* Choose SPI chip-selects */
 611         for (i = 0; i < nr_devices; i++) {
 612                 if (devices[i].controller_data)
 613                         cs_pin = (unsigned long) devices[i].controller_data;
 614                 else if (devices[i].bus_num == 0)
 615                         cs_pin = spi0_standard_cs[devices[i].chip_select];
 616                 else
 617                         cs_pin = spi1_standard_cs[devices[i].chip_select];
 618
 619                 if (devices[i].bus_num == 0)
 620                         enable_spi0 = 1;
 621                 else
 622                         enable_spi1 = 1;
 623
 624                 /* enable chip-select pin */
 625                 at91_set_gpio_output(cs_pin, 1);
 626
 627                 /* pass chip-select pin to driver */
 628                 devices[i].controller_data = (void *) cs_pin;
 629         }
 630
 631         spi_register_board_info(devices, nr_devices);
 632
 633         /* Configure SPI bus(es) */
 634         if (enable_spi0) {
 635                 at91_set_A_periph(AT91_PIN_PB0, 0);     /* SPI0_MISO */
 636                 at91_set_A_periph(AT91_PIN_PB1, 0);     /* SPI0_MOSI */
 637                 at91_set_A_periph(AT91_PIN_PB2, 0);     /* SPI0_SPCK */
 638
 639                 at91_clock_associate("spi0_clk", &at91sam9g45_spi0_device.dev, "spi_clk");
 640                 platform_device_register(&at91sam9g45_spi0_device);
 641         }
 642         if (enable_spi1) {
 643                 at91_set_A_periph(AT91_PIN_PB14, 0);    /* SPI1_MISO */
 644                 at91_set_A_periph(AT91_PIN_PB15, 0);    /* SPI1_MOSI */
 645                 at91_set_A_periph(AT91_PIN_PB16, 0);    /* SPI1_SPCK */
 646
 647                 at91_clock_associate("spi1_clk", &at91sam9g45_spi1_device.dev, "spi_clk");
 648                 platform_device_register(&at91sam9g45_spi1_device);
 649         }
 650 }
 651 #else
 652 void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
 653 #endif
 654
 655
 656 /* --------------------------------------------------------------------
 657  *  AC97
 658  * -------------------------------------------------------------------- */
 659
 660 #if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
 661 static u64 ac97_dmamask = DMA_BIT_MASK(32);
 662 static struct ac97c_platform_data ac97_data;
 663
 664 static struct resource ac97_resources[] = {
 665         [0] = {
 666                 .start  = AT91SAM9G45_BASE_AC97C,
 667                 .end    = AT91SAM9G45_BASE_AC97C + SZ_16K - 1,
 668                 .flags  = IORESOURCE_MEM,
 669         },
 670         [1] = {
 671                 .start  = AT91SAM9G45_ID_AC97C,
 672                 .end    = AT91SAM9G45_ID_AC97C,
 673                 .flags  = IORESOURCE_IRQ,
 674         },
 675 };
 676
 677 static struct platform_device at91sam9g45_ac97_device = {
 678         .name           = "atmel_ac97c",
 679         .id             = 0,
 680         .dev            = {
 681                                 .dma_mask               = &ac97_dmamask,
 682                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 683                                 .platform_data          = &ac97_data,
 684         },
 685         .resource       = ac97_resources,
 686         .num_resources  = ARRAY_SIZE(ac97_resources),
 687 };
 688
 689 void __init at91_add_device_ac97(struct ac97c_platform_data *data)
 690 {
 691         if (!data)
 692                 return;
 693
 694         at91_set_A_periph(AT91_PIN_PD8, 0);     /* AC97FS */
 695         at91_set_A_periph(AT91_PIN_PD9, 0);     /* AC97CK */
 696         at91_set_A_periph(AT91_PIN_PD7, 0);     /* AC97TX */
 697         at91_set_A_periph(AT91_PIN_PD6, 0);     /* AC97RX */
 698
 699         /* reset */
 700         if (data->reset_pin)
 701                 at91_set_gpio_output(data->reset_pin, 0);
 702
 703         ac97_data = *data;
 704         platform_device_register(&at91sam9g45_ac97_device);
 705 }
 706 #else
 707 void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
 708 #endif
 709
 710
 711 /* --------------------------------------------------------------------
 712  *  LCD Controller
 713  * -------------------------------------------------------------------- */
 714
 715 #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
 716 static u64 lcdc_dmamask = DMA_BIT_MASK(32);
 717 static struct atmel_lcdfb_info lcdc_data;
 718
 719 static struct resource lcdc_resources[] = {
 720         [0] = {
 721                 .start  = AT91SAM9G45_LCDC_BASE,
 722                 .end    = AT91SAM9G45_LCDC_BASE + SZ_4K - 1,
 723                 .flags  = IORESOURCE_MEM,
 724         },
 725         [1] = {
 726                 .start  = AT91SAM9G45_ID_LCDC,
 727                 .end    = AT91SAM9G45_ID_LCDC,
 728                 .flags  = IORESOURCE_IRQ,
 729         },
 730 };
 731
 732 static struct platform_device at91_lcdc_device = {
 733         .name           = "atmel_lcdfb",
 734         .id             = 0,
 735         .dev            = {
 736                                 .dma_mask               = &lcdc_dmamask,
 737                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 738                                 .platform_data          = &lcdc_data,
 739         },
 740         .resource       = lcdc_resources,
 741         .num_resources  = ARRAY_SIZE(lcdc_resources),
 742 };
 743
 744 void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data)
 745 {
 746         if (!data)
 747                 return;
 748
 749         at91_set_A_periph(AT91_PIN_PE0, 0);     /* LCDDPWR */
 750
 751         at91_set_A_periph(AT91_PIN_PE2, 0);     /* LCDCC */
 752         at91_set_A_periph(AT91_PIN_PE3, 0);     /* LCDVSYNC */
 753         at91_set_A_periph(AT91_PIN_PE4, 0);     /* LCDHSYNC */
 754         at91_set_A_periph(AT91_PIN_PE5, 0);     /* LCDDOTCK */
 755         at91_set_A_periph(AT91_PIN_PE6, 0);     /* LCDDEN */
 756         at91_set_A_periph(AT91_PIN_PE7, 0);     /* LCDD0 */
 757         at91_set_A_periph(AT91_PIN_PE8, 0);     /* LCDD1 */
 758         at91_set_A_periph(AT91_PIN_PE9, 0);     /* LCDD2 */
 759         at91_set_A_periph(AT91_PIN_PE10, 0);    /* LCDD3 */
 760         at91_set_A_periph(AT91_PIN_PE11, 0);    /* LCDD4 */
 761         at91_set_A_periph(AT91_PIN_PE12, 0);    /* LCDD5 */
 762         at91_set_A_periph(AT91_PIN_PE13, 0);    /* LCDD6 */
 763         at91_set_A_periph(AT91_PIN_PE14, 0);    /* LCDD7 */
 764         at91_set_A_periph(AT91_PIN_PE15, 0);    /* LCDD8 */
 765         at91_set_A_periph(AT91_PIN_PE16, 0);    /* LCDD9 */
 766         at91_set_A_periph(AT91_PIN_PE17, 0);    /* LCDD10 */
 767         at91_set_A_periph(AT91_PIN_PE18, 0);    /* LCDD11 */
 768         at91_set_A_periph(AT91_PIN_PE19, 0);    /* LCDD12 */
 769         at91_set_A_periph(AT91_PIN_PE20, 0);    /* LCDD13 */
 770         at91_set_A_periph(AT91_PIN_PE21, 0);    /* LCDD14 */
 771         at91_set_A_periph(AT91_PIN_PE22, 0);    /* LCDD15 */
 772         at91_set_A_periph(AT91_PIN_PE23, 0);    /* LCDD16 */
 773         at91_set_A_periph(AT91_PIN_PE24, 0);    /* LCDD17 */
 774         at91_set_A_periph(AT91_PIN_PE25, 0);    /* LCDD18 */
 775         at91_set_A_periph(AT91_PIN_PE26, 0);    /* LCDD19 */
 776         at91_set_A_periph(AT91_PIN_PE27, 0);    /* LCDD20 */
 777         at91_set_A_periph(AT91_PIN_PE28, 0);    /* LCDD21 */
 778         at91_set_A_periph(AT91_PIN_PE29, 0);    /* LCDD22 */
 779         at91_set_A_periph(AT91_PIN_PE30, 0);    /* LCDD23 */
 780
 781         lcdc_data = *data;
 782         platform_device_register(&at91_lcdc_device);
 783 }
 784 #else
 785 void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data) {}
 786 #endif
 787
 788
 789 /* --------------------------------------------------------------------
 790  *  Timer/Counter block
 791  * -------------------------------------------------------------------- */
 792
 793 #ifdef CONFIG_ATMEL_TCLIB
 794 static struct resource tcb0_resources[] = {
 795         [0] = {
 796                 .start  = AT91SAM9G45_BASE_TCB0,
 797                 .end    = AT91SAM9G45_BASE_TCB0 + SZ_16K - 1,
 798                 .flags  = IORESOURCE_MEM,
 799         },
 800         [1] = {
 801                 .start  = AT91SAM9G45_ID_TCB,
 802                 .end    = AT91SAM9G45_ID_TCB,
 803                 .flags  = IORESOURCE_IRQ,
 804         },
 805 };
 806
 807 static struct platform_device at91sam9g45_tcb0_device = {
 808         .name           = "atmel_tcb",
 809         .id             = 0,
 810         .resource       = tcb0_resources,
 811         .num_resources  = ARRAY_SIZE(tcb0_resources),
 812 };
 813
 814 /* TCB1 begins with TC3 */
 815 static struct resource tcb1_resources[] = {
 816         [0] = {
 817                 .start  = AT91SAM9G45_BASE_TCB1,
 818                 .end    = AT91SAM9G45_BASE_TCB1 + SZ_16K - 1,
 819                 .flags  = IORESOURCE_MEM,
 820         },
 821         [1] = {
 822                 .start  = AT91SAM9G45_ID_TCB,
 823                 .end    = AT91SAM9G45_ID_TCB,
 824                 .flags  = IORESOURCE_IRQ,
 825         },
 826 };
 827
 828 static struct platform_device at91sam9g45_tcb1_device = {
 829         .name           = "atmel_tcb",
 830         .id             = 1,
 831         .resource       = tcb1_resources,
 832         .num_resources  = ARRAY_SIZE(tcb1_resources),
 833 };
 834
 835 static void __init at91_add_device_tc(void)
 836 {
 837         /* this chip has one clock and irq for all six TC channels */
 838         at91_clock_associate("tcb_clk", &at91sam9g45_tcb0_device.dev, "t0_clk");
 839         platform_device_register(&at91sam9g45_tcb0_device);
 840         at91_clock_associate("tcb_clk", &at91sam9g45_tcb1_device.dev, "t0_clk");
 841         platform_device_register(&at91sam9g45_tcb1_device);
 842 }
 843 #else
 844 static void __init at91_add_device_tc(void) { }
 845 #endif
 846
 847
 848 /* --------------------------------------------------------------------
 849  *  RTC
 850  * -------------------------------------------------------------------- */
 851
 852 #if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE)
 853 static struct platform_device at91sam9g45_rtc_device = {
 854         .name           = "at91_rtc",
 855         .id             = -1,
 856         .num_resources  = 0,
 857 };
 858
 859 static void __init at91_add_device_rtc(void)
 860 {
 861         platform_device_register(&at91sam9g45_rtc_device);
 862 }
 863 #else
 864 static void __init at91_add_device_rtc(void) {}
 865 #endif
 866
 867
 868 /* --------------------------------------------------------------------
 869  *  RTT
 870  * -------------------------------------------------------------------- */
 871
 872 static struct resource rtt_resources[] = {
 873         {
 874                 .start  = AT91_BASE_SYS + AT91_RTT,
 875                 .end    = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1,
 876                 .flags  = IORESOURCE_MEM,
 877         }
 878 };
 879
 880 static struct platform_device at91sam9g45_rtt_device = {
 881         .name           = "at91_rtt",
 882         .id             = 0,
 883         .resource       = rtt_resources,
 884         .num_resources  = ARRAY_SIZE(rtt_resources),
 885 };
 886
 887 static void __init at91_add_device_rtt(void)
 888 {
 889         platform_device_register(&at91sam9g45_rtt_device);
 890 }
 891
 892
 893 /* --------------------------------------------------------------------
 894  *  Watchdog
 895  * -------------------------------------------------------------------- */
 896
 897 #if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
 898 static struct platform_device at91sam9g45_wdt_device = {
 899         .name           = "at91_wdt",
 900         .id             = -1,
 901         .num_resources  = 0,
 902 };
 903
 904 static void __init at91_add_device_watchdog(void)
 905 {
 906         platform_device_register(&at91sam9g45_wdt_device);
 907 }
 908 #else
 909 static void __init at91_add_device_watchdog(void) {}
 910 #endif
 911
 912
 913 /* --------------------------------------------------------------------
 914  *  PWM
 915  * --------------------------------------------------------------------*/
 916
 917 #if defined(CONFIG_ATMEL_PWM) || defined(CONFIG_ATMEL_PWM_MODULE)
 918 static u32 pwm_mask;
 919
 920 static struct resource pwm_resources[] = {
 921         [0] = {
 922                 .start  = AT91SAM9G45_BASE_PWMC,
 923                 .end    = AT91SAM9G45_BASE_PWMC + SZ_16K - 1,
 924                 .flags  = IORESOURCE_MEM,
 925         },
 926         [1] = {
 927                 .start  = AT91SAM9G45_ID_PWMC,
 928                 .end    = AT91SAM9G45_ID_PWMC,
 929                 .flags  = IORESOURCE_IRQ,
 930         },
 931 };
 932
 933 static struct platform_device at91sam9g45_pwm0_device = {
 934         .name   = "atmel_pwm",
 935         .id     = -1,
 936         .dev    = {
 937                 .platform_data          = &pwm_mask,
 938         },
 939         .resource       = pwm_resources,
 940         .num_resources  = ARRAY_SIZE(pwm_resources),
 941 };
 942
 943 void __init at91_add_device_pwm(u32 mask)
 944 {
 945         if (mask & (1 << AT91_PWM0))
 946                 at91_set_B_periph(AT91_PIN_PD24, 1);    /* enable PWM0 */
 947
 948         if (mask & (1 << AT91_PWM1))
 949                 at91_set_B_periph(AT91_PIN_PD31, 1);    /* enable PWM1 */
 950
 951         if (mask & (1 << AT91_PWM2))
 952                 at91_set_B_periph(AT91_PIN_PD26, 1);    /* enable PWM2 */
 953
 954         if (mask & (1 << AT91_PWM3))
 955                 at91_set_B_periph(AT91_PIN_PD0, 1);     /* enable PWM3 */
 956
 957         pwm_mask = mask;
 958
 959         platform_device_register(&at91sam9g45_pwm0_device);
 960 }
 961 #else
 962 void __init at91_add_device_pwm(u32 mask) {}
 963 #endif
 964
 965
 966 /* --------------------------------------------------------------------
 967  *  SSC -- Synchronous Serial Controller
 968  * -------------------------------------------------------------------- */
 969
 970 #if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
 971 static u64 ssc0_dmamask = DMA_BIT_MASK(32);
 972
 973 static struct resource ssc0_resources[] = {
 974         [0] = {
 975                 .start  = AT91SAM9G45_BASE_SSC0,
 976                 .end    = AT91SAM9G45_BASE_SSC0 + SZ_16K - 1,
 977                 .flags  = IORESOURCE_MEM,
 978         },
 979         [1] = {
 980                 .start  = AT91SAM9G45_ID_SSC0,
 981                 .end    = AT91SAM9G45_ID_SSC0,
 982                 .flags  = IORESOURCE_IRQ,
 983         },
 984 };
 985
 986 static struct platform_device at91sam9g45_ssc0_device = {
 987         .name   = "ssc",
 988         .id     = 0,
 989         .dev    = {
 990                 .dma_mask               = &ssc0_dmamask,
 991                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 992         },
 993         .resource       = ssc0_resources,
 994         .num_resources  = ARRAY_SIZE(ssc0_resources),
 995 };
 996
 997 static inline void configure_ssc0_pins(unsigned pins)
 998 {
 999         if (pins & ATMEL_SSC_TF)
1000                 at91_set_A_periph(AT91_PIN_PD1, 1);
1001         if (pins & ATMEL_SSC_TK)
1002                 at91_set_A_periph(AT91_PIN_PD0, 1);
1003         if (pins & ATMEL_SSC_TD)
1004                 at91_set_A_periph(AT91_PIN_PD2, 1);
1005         if (pins & ATMEL_SSC_RD)
1006                 at91_set_A_periph(AT91_PIN_PD3, 1);
1007         if (pins & ATMEL_SSC_RK)
1008                 at91_set_A_periph(AT91_PIN_PD4, 1);
1009         if (pins & ATMEL_SSC_RF)
1010                 at91_set_A_periph(AT91_PIN_PD5, 1);
1011 }
1012
1013 static u64 ssc1_dmamask = DMA_BIT_MASK(32);
1014
1015 static struct resource ssc1_resources[] = {
1016         [0] = {
1017                 .start  = AT91SAM9G45_BASE_SSC1,
1018                 .end    = AT91SAM9G45_BASE_SSC1 + SZ_16K - 1,
1019                 .flags  = IORESOURCE_MEM,
1020         },
1021         [1] = {
1022                 .start  = AT91SAM9G45_ID_SSC1,
1023                 .end    = AT91SAM9G45_ID_SSC1,
1024                 .flags  = IORESOURCE_IRQ,
1025         },
1026 };
1027
1028 static struct platform_device at91sam9g45_ssc1_device = {
1029         .name   = "ssc",
1030         .id     = 1,
1031         .dev    = {
1032                 .dma_mask               = &ssc1_dmamask,
1033                 .coherent_dma_mask      = DMA_BIT_MASK(32),
1034         },
1035         .resource       = ssc1_resources,
1036         .num_resources  = ARRAY_SIZE(ssc1_resources),
1037 };
1038
1039 static inline void configure_ssc1_pins(unsigned pins)
1040 {
1041         if (pins & ATMEL_SSC_TF)
1042                 at91_set_A_periph(AT91_PIN_PD14, 1);
1043         if (pins & ATMEL_SSC_TK)
1044                 at91_set_A_periph(AT91_PIN_PD12, 1);
1045         if (pins & ATMEL_SSC_TD)
1046                 at91_set_A_periph(AT91_PIN_PD10, 1);
1047         if (pins & ATMEL_SSC_RD)
1048                 at91_set_A_periph(AT91_PIN_PD11, 1);
1049         if (pins & ATMEL_SSC_RK)
1050                 at91_set_A_periph(AT91_PIN_PD13, 1);
1051         if (pins & ATMEL_SSC_RF)
1052                 at91_set_A_periph(AT91_PIN_PD15, 1);
1053 }
1054
1055 /*
1056  * SSC controllers are accessed through library code, instead of any
1057  * kind of all-singing/all-dancing driver.  For example one could be
1058  * used by a particular I2S audio codec's driver, while another one
1059  * on the same system might be used by a custom data capture driver.
1060  */
1061 void __init at91_add_device_ssc(unsigned id, unsigned pins)
1062 {
1063         struct platform_device *pdev;
1064
1065         /*
1066          * NOTE: caller is responsible for passing information matching
1067          * "pins" to whatever will be using each particular controller.
1068          */
1069         switch (id) {
1070         case AT91SAM9G45_ID_SSC0:
1071                 pdev = &at91sam9g45_ssc0_device;
1072                 configure_ssc0_pins(pins);
1073                 at91_clock_associate("ssc0_clk", &pdev->dev, "pclk");
1074                 break;
1075         case AT91SAM9G45_ID_SSC1:
1076                 pdev = &at91sam9g45_ssc1_device;
1077                 configure_ssc1_pins(pins);
1078                 at91_clock_associate("ssc1_clk", &pdev->dev, "pclk");
1079                 break;
1080         default:
1081                 return;
1082         }
1083
1084         platform_device_register(pdev);
1085 }
1086
1087 #else
1088 void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
1089 #endif
1090
1091
1092 /* --------------------------------------------------------------------
1093  *  UART
1094  * -------------------------------------------------------------------- */
1095
1096 #if defined(CONFIG_SERIAL_ATMEL)
1097 static struct resource dbgu_resources[] = {
1098         [0] = {
1099                 .start  = AT91_VA_BASE_SYS + AT91_DBGU,
1100                 .end    = AT91_VA_BASE_SYS + AT91_DBGU + SZ_512 - 1,
1101                 .flags  = IORESOURCE_MEM,
1102         },
1103         [1] = {
1104                 .start  = AT91_ID_SYS,
1105                 .end    = AT91_ID_SYS,
1106                 .flags  = IORESOURCE_IRQ,
1107         },
1108 };
1109
1110 static struct atmel_uart_data dbgu_data = {
1111         .use_dma_tx     = 0,
1112         .use_dma_rx     = 0,
1113         .regs           = (void __iomem *)(AT91_VA_BASE_SYS + AT91_DBGU),
1114 };
1115
1116 static u64 dbgu_dmamask = DMA_BIT_MASK(32);
1117
1118 static struct platform_device at91sam9g45_dbgu_device = {
1119         .name           = "atmel_usart",
1120         .id             = 0,
1121         .dev            = {
1122                                 .dma_mask               = &dbgu_dmamask,
1123                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
1124                                 .platform_data          = &dbgu_data,
1125         },
1126         .resource       = dbgu_resources,
1127         .num_resources  = ARRAY_SIZE(dbgu_resources),
1128 };
1129
1130 static inline void configure_dbgu_pins(void)
1131 {
1132         at91_set_A_periph(AT91_PIN_PB12, 0);            /* DRXD */
1133         at91_set_A_periph(AT91_PIN_PB13, 1);            /* DTXD */
1134 }
1135
1136 static struct resource uart0_resources[] = {
1137         [0] = {
1138                 .start  = AT91SAM9G45_BASE_US0,
1139                 .end    = AT91SAM9G45_BASE_US0 + SZ_16K - 1,
1140                 .flags  = IORESOURCE_MEM,
1141         },
1142         [1] = {
1143                 .start  = AT91SAM9G45_ID_US0,
1144                 .end    = AT91SAM9G45_ID_US0,
1145                 .flags  = IORESOURCE_IRQ,
1146         },
1147 };
1148
1149 static struct atmel_uart_data uart0_data = {
1150         .use_dma_tx     = 1,
1151         .use_dma_rx     = 1,
1152 };
1153
1154 static u64 uart0_dmamask = DMA_BIT_MASK(32);
1155
1156 static struct platform_device at91sam9g45_uart0_device = {
1157         .name           = "atmel_usart",
1158         .id             = 1,
1159         .dev            = {
1160                                 .dma_mask               = &uart0_dmamask,
1161                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
1162                                 .platform_data          = &uart0_data,
1163         },
1164         .resource       = uart0_resources,
1165         .num_resources  = ARRAY_SIZE(uart0_resources),
1166 };
1167
1168 static inline void configure_usart0_pins(unsigned pins)
1169 {
1170         at91_set_A_periph(AT91_PIN_PB19, 1);            /* TXD0 */
1171         at91_set_A_periph(AT91_PIN_PB18, 0);            /* RXD0 */
1172
1173         if (pins & ATMEL_UART_RTS)
1174                 at91_set_B_periph(AT91_PIN_PB17, 0);    /* RTS0 */
1175         if (pins & ATMEL_UART_CTS)
1176                 at91_set_B_periph(AT91_PIN_PB15, 0);    /* CTS0 */
1177 }
1178
1179 static struct resource uart1_resources[] = {
1180         [0] = {
1181                 .start  = AT91SAM9G45_BASE_US1,
1182                 .end    = AT91SAM9G45_BASE_US1 + SZ_16K - 1,
1183                 .flags  = IORESOURCE_MEM,
1184         },
1185         [1] = {
1186                 .start  = AT91SAM9G45_ID_US1,
1187                 .end    = AT91SAM9G45_ID_US1,
1188                 .flags  = IORESOURCE_IRQ,
1189         },
1190 };
1191
1192 static struct atmel_uart_data uart1_data = {
1193         .use_dma_tx     = 1,
1194         .use_dma_rx     = 1,
1195 };
1196
1197 static u64 uart1_dmamask = DMA_BIT_MASK(32);
1198
1199 static struct platform_device at91sam9g45_uart1_device = {
1200         .name           = "atmel_usart",
1201         .id             = 2,
1202         .dev            = {
1203                                 .dma_mask               = &uart1_dmamask,
1204                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
1205                                 .platform_data          = &uart1_data,
1206         },
1207         .resource       = uart1_resources,
1208         .num_resources  = ARRAY_SIZE(uart1_resources),
1209 };
1210
1211 static inline void configure_usart1_pins(unsigned pins)
1212 {
1213         at91_set_A_periph(AT91_PIN_PB4, 1);             /* TXD1 */
1214         at91_set_A_periph(AT91_PIN_PB5, 0);             /* RXD1 */
1215
1216         if (pins & ATMEL_UART_RTS)
1217                 at91_set_A_periph(AT91_PIN_PD16, 0);    /* RTS1 */
1218         if (pins & ATMEL_UART_CTS)
1219                 at91_set_A_periph(AT91_PIN_PD17, 0);    /* CTS1 */
1220 }
1221
1222 static struct resource uart2_resources[] = {
1223         [0] = {
1224                 .start  = AT91SAM9G45_BASE_US2,
1225                 .end    = AT91SAM9G45_BASE_US2 + SZ_16K - 1,
1226                 .flags  = IORESOURCE_MEM,
1227         },
1228         [1] = {
1229                 .start  = AT91SAM9G45_ID_US2,
1230                 .end    = AT91SAM9G45_ID_US2,
1231                 .flags  = IORESOURCE_IRQ,
1232         },
1233 };
1234
1235 static struct atmel_uart_data uart2_data = {
1236         .use_dma_tx     = 1,
1237         .use_dma_rx     = 1,
1238 };
1239
1240 static u64 uart2_dmamask = DMA_BIT_MASK(32);
1241
1242 static struct platform_device at91sam9g45_uart2_device = {
1243         .name           = "atmel_usart",
1244         .id             = 3,
1245         .dev            = {
1246                                 .dma_mask               = &uart2_dmamask,
1247                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
1248                                 .platform_data          = &uart2_data,
1249         },
1250         .resource       = uart2_resources,
1251         .num_resources  = ARRAY_SIZE(uart2_resources),
1252 };
1253
1254 static inline void configure_usart2_pins(unsigned pins)
1255 {
1256         at91_set_A_periph(AT91_PIN_PB6, 1);             /* TXD2 */
1257         at91_set_A_periph(AT91_PIN_PB7, 0);             /* RXD2 */
1258
1259         if (pins & ATMEL_UART_RTS)
1260                 at91_set_B_periph(AT91_PIN_PC9, 0);     /* RTS2 */
1261         if (pins & ATMEL_UART_CTS)
1262                 at91_set_B_periph(AT91_PIN_PC11, 0);    /* CTS2 */
1263 }
1264
1265 static struct resource uart3_resources[] = {
1266         [0] = {
1267                 .start  = AT91SAM9G45_BASE_US3,
1268                 .end    = AT91SAM9G45_BASE_US3 + SZ_16K - 1,
1269                 .flags  = IORESOURCE_MEM,
1270         },
1271         [1] = {
1272                 .start  = AT91SAM9G45_ID_US3,
1273                 .end    = AT91SAM9G45_ID_US3,
1274                 .flags  = IORESOURCE_IRQ,
1275         },
1276 };
1277
1278 static struct atmel_uart_data uart3_data = {
1279         .use_dma_tx     = 1,
1280         .use_dma_rx     = 1,
1281 };
1282
1283 static u64 uart3_dmamask = DMA_BIT_MASK(32);
1284
1285 static struct platform_device at91sam9g45_uart3_device = {
1286         .name           = "atmel_usart",
1287         .id             = 4,
1288         .dev            = {
1289                                 .dma_mask               = &uart3_dmamask,
1290                                 .coherent_dma_mask      = DMA_BIT_MASK(32),
1291                                 .platform_data          = &uart3_data,
1292         },
1293         .resource       = uart3_resources,
1294         .num_resources  = ARRAY_SIZE(uart3_resources),
1295 };
1296
1297 static inline void configure_usart3_pins(unsigned pins)
1298 {
1299         at91_set_A_periph(AT91_PIN_PB8, 1);             /* TXD3 */
1300         at91_set_A_periph(AT91_PIN_PB9, 0);             /* RXD3 */
1301
1302         if (pins & ATMEL_UART_RTS)
1303                 at91_set_B_periph(AT91_PIN_PA23, 0);    /* RTS3 */
1304         if (pins & ATMEL_UART_CTS)
1305                 at91_set_B_periph(AT91_PIN_PA24, 0);    /* CTS3 */
1306 }
1307
1308 static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART];   /* the UARTs to use */
1309 struct platform_device *atmel_default_console_device;   /* the serial console device */
1310
1311 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
1312 {
1313         struct platform_device *pdev;
1314
1315         switch (id) {
1316                 case 0:         /* DBGU */
1317                         pdev = &at91sam9g45_dbgu_device;
1318                         configure_dbgu_pins();
1319                         at91_clock_associate("mck", &pdev->dev, "usart");
1320                         break;
1321                 case AT91SAM9G45_ID_US0:
1322                         pdev = &at91sam9g45_uart0_device;
1323                         configure_usart0_pins(pins);
1324                         at91_clock_associate("usart0_clk", &pdev->dev, "usart");
1325                         break;
1326                 case AT91SAM9G45_ID_US1:
1327                         pdev = &at91sam9g45_uart1_device;
1328                         configure_usart1_pins(pins);
1329                         at91_clock_associate("usart1_clk", &pdev->dev, "usart");
1330                         break;
1331                 case AT91SAM9G45_ID_US2:
1332                         pdev = &at91sam9g45_uart2_device;
1333                         configure_usart2_pins(pins);
1334                         at91_clock_associate("usart2_clk", &pdev->dev, "usart");
1335                         break;
1336                 case AT91SAM9G45_ID_US3:
1337                         pdev = &at91sam9g45_uart3_device;
1338                         configure_usart3_pins(pins);
1339                         at91_clock_associate("usart3_clk", &pdev->dev, "usart");
1340                         break;
1341                 default:
1342                         return;
1343         }
1344         pdev->id = portnr;              /* update to mapped ID */
1345
1346         if (portnr < ATMEL_MAX_UART)
1347                 at91_uarts[portnr] = pdev;
1348 }
1349
1350 void __init at91_set_serial_console(unsigned portnr)
1351 {
1352         if (portnr < ATMEL_MAX_UART)
1353                 atmel_default_console_device = at91_uarts[portnr];
1354 }
1355
1356 void __init at91_add_device_serial(void)
1357 {
1358         int i;
1359
1360         for (i = 0; i < ATMEL_MAX_UART; i++) {
1361                 if (at91_uarts[i])
1362                         platform_device_register(at91_uarts[i]);
1363         }
1364
1365         if (!atmel_default_console_device)
1366                 printk(KERN_INFO "AT91: No default serial console defined.\n");
1367 }
1368 #else
1369 void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
1370 void __init at91_set_serial_console(unsigned portnr) {}
1371 void __init at91_add_device_serial(void) {}
1372 #endif
1373
1374
1375 /* -------------------------------------------------------------------- */
1376 /*
1377  * These devices are always present and don't need any board-specific
1378  * setup.
1379  */
1380 static int __init at91_add_standard_devices(void)
1381 {
1382         at91_add_device_hdmac();
1383         at91_add_device_rtc();
1384         at91_add_device_rtt();
1385         at91_add_device_watchdog();
1386         at91_add_device_tc();
1387         return 0;
1388 }
1389
1390 arch_initcall(at91_add_standard_devices);