Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik...
[pandora-kernel.git] / Documentation / hwmon / w83627hf
1 Kernel driver w83627hf
2 ======================
3
4 Supported chips:
5   * Winbond W83627HF (ISA accesses ONLY)
6     Prefix: 'w83627hf'
7     Addresses scanned: ISA address retrieved from Super I/O registers
8     Datasheet: http://www.winbond.com/PDF/sheet/w83627hf.pdf
9   * Winbond W83627THF
10     Prefix: 'w83627thf'
11     Addresses scanned: ISA address retrieved from Super I/O registers
12     Datasheet: http://www.winbond.com/PDF/sheet/w83627thf.pdf
13   * Winbond W83697HF
14     Prefix: 'w83697hf'
15     Addresses scanned: ISA address retrieved from Super I/O registers
16     Datasheet: http://www.winbond.com/PDF/sheet/697hf.pdf
17   * Winbond W83637HF
18     Prefix: 'w83637hf'
19     Addresses scanned: ISA address retrieved from Super I/O registers
20     Datasheet: http://www.winbond.com/PDF/sheet/w83637hf.pdf
21   * Winbond W83687THF
22     Prefix: 'w83687thf'
23     Addresses scanned: ISA address retrieved from Super I/O registers
24     Datasheet: Provided by Winbond on request
25
26 Authors:
27         Frodo Looijaard <frodol@dds.nl>,
28         Philip Edelbrock <phil@netroedge.com>,
29         Mark Studebaker <mdsxyz123@yahoo.com>,
30         Bernhard C. Schrenk <clemy@clemy.org>
31
32 Module Parameters
33 -----------------
34
35 * force_addr: int
36   Initialize the ISA address of the sensors
37 * force_i2c: int
38   Initialize the I2C address of the sensors
39 * init: int
40   (default is 1)
41   Use 'init=0' to bypass initializing the chip.
42   Try this if your computer crashes when you load the module.
43 * reset: int
44   (default is 0)
45   The driver used to reset the chip on load, but does no more. Use
46   'reset=1' to restore the old behavior. Report if you need to do this.
47
48 Description
49 -----------
50
51 This driver implements support for ISA accesses *only* for
52 the Winbond W83627HF, W83627THF, W83697HF and W83637HF Super I/O chips.
53 We will refer to them collectively as Winbond chips.
54
55 This driver supports ISA accesses, which should be more reliable
56 than i2c accesses. Also, for Tyan boards which contain both a
57 Super I/O chip and a second i2c-only Winbond chip (often a W83782D),
58 using this driver will avoid i2c address conflicts and complex
59 initialization that were required in the w83781d driver.
60
61 If you really want i2c accesses for these Super I/O chips,
62 use the w83781d driver. However this is not the preferred method
63 now that this ISA driver has been developed.
64
65 The w83627_HF_ uses pins 110-106 as VID0-VID4. The w83627_THF_ uses the
66 same pins as GPIO[0:4]. Technically, the w83627_THF_ does not support a
67 VID reading. However the two chips have the identical 128 pin package. So,
68 it is possible or even likely for a w83627thf to have the VID signals routed
69 to these pins despite their not being labeled for that purpose. Therefore,
70 the w83627thf driver interprets these as VID. If the VID on your board
71 doesn't work, first see doc/vid in the lm_sensors package[1]. If that still
72 doesn't help, you may just ignore the bogus VID reading with no harm done.
73
74 For further information on this driver see the w83781d driver documentation.
75
76 [1] http://www2.lm-sensors.nu/~lm78/cvs/browse.cgi/lm_sensors2/doc/vid
77