Changes for U-Boot 1.1.1:
======================================================================
+* Temporarily disabled John Kerl's extended MII command code because
+ "miivals.h" is missing
+
+* Patches by Mark Jonas, 13 Apr 2004:
+ - Remove CS0 chip select timing setting from cpu/mpc5xxx/start.S
+ - Add sync instructions to IceCube SDRAM init code
+ - Move SDRAM chip constants into seperate include files
+ - Unify DDR and SDR initialization code
+ - Unify all IceCube (Lite5xxx) target names
+
* Patch by John Kerl, 16 Apr 2004:
Enable ranges in mii command, e.g. mii read 0-1f 0 or
mii read 4-7 18-1a. Also add mii dump subcommand for
#########################################################################
LIST_5xxx=" \
- IceCube_5100 IceCube_5200 EVAL5200 PM520 \
+ icecube_5100 icecube_5200 EVAL5200 PM520 \
"
#########################################################################
#########################################################################
## MPC5xxx Systems
#########################################################################
-MPC5200LITE_config \
-MPC5200LITE_LOWBOOT_config \
-MPC5200LITE_LOWBOOT08_config \
-icecube_5200_DDR_config \
-IceCube_5200_DDR_config \
-icecube_5200_DDR_LOWBOOT_config \
-icecube_5200_DDR_LOWBOOT08_config \
-icecube_5200_config \
-IceCube_5200_config \
-IceCube_5100_config: unconfig
+Lite5200_config \
+Lite5200_LOWBOOT_config \
+Lite5200_LOWBOOT08_config \
+icecube_5200_config \
+icecube_5200_LOWBOOT_config \
+icecube_5200_LOWBOOT08_config \
+icecube_5200_DDR_config \
+icecube_5200_DDR_LOWBOOT_config \
+icecube_5200_DDR_LOWBOOT08_config \
+icecube_5100_config: unconfig
@ >include/config.h
@[ -z "$(findstring LOWBOOT_,$@)" ] || \
{ if [ "$(findstring DDR,$@)" ] ; \
* (C) Copyright 2003
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
* See file CREDITS for list of people who contributed to this
* project.
*
#include <mpc5xxx.h>
#include <pci.h>
+#if defined(CONFIG_MPC5200_DDR)
+#include "mt46v16m16-75.h"
+#else
+#include "mt48lc16m16a2-75.h"
+#endif
+
#ifndef CFG_RAMBOOT
static void sdram_start (int hi_addr)
{
long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-#ifdef CONFIG_MPC5200_DDR
/* unlock mode register */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f00 | hi_addr_bit;
+ *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
+ __asm__ volatile ("sync");
+
/* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f02 | hi_addr_bit;
+ *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+ __asm__ volatile ("sync");
+
+#if SDRAM_DDR
/* set mode register: extended mode */
- *(vu_long *)MPC5XXX_SDRAM_MODE = 0x40090000;
+ *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
+ __asm__ volatile ("sync");
+
/* set mode register: reset DLL */
- *(vu_long *)MPC5XXX_SDRAM_MODE = 0x058d0000;
- /* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f02 | hi_addr_bit;
- /* auto refresh */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f04 | hi_addr_bit;
- /* set mode register */
- *(vu_long *)MPC5XXX_SDRAM_MODE = 0x018d0000;
- /* normal operation */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = 0x705f0f00 | hi_addr_bit;
-#else
- /* unlock mode register */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0000 | hi_addr_bit;
- /* precharge all banks */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0002 | hi_addr_bit;
- /* set mode register */
-#if defined(CONFIG_MPC5200)
- *(vu_long *)MPC5XXX_SDRAM_MODE = 0x00cd0000;
-#elif defined(CONFIG_MGT5100)
- *(vu_long *)MPC5XXX_SDRAM_MODE = 0x008d0000;
+ *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
+ __asm__ volatile ("sync");
#endif
+
+ /* precharge all banks */
+ *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+ __asm__ volatile ("sync");
+
/* auto refresh */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0004 | hi_addr_bit;
- /* auto refresh */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0004 | hi_addr_bit;
+ *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
+ __asm__ volatile ("sync");
+
/* set mode register */
- *(vu_long *)MPC5XXX_SDRAM_MODE = 0x00cd0000;
+ *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
+ __asm__ volatile ("sync");
+
/* normal operation */
- *(vu_long *)MPC5XXX_SDRAM_CTRL = 0x504f0000 | hi_addr_bit;
-#endif
+ *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
+ __asm__ volatile ("sync");
}
#endif
+/*
+ * ATTENTION: Although partially referenced initdram does NOT make real use
+ * use of CFG_SDRAM_BASE. The code does not work if CFG_SDRAM_BASE
+ * is something else than 0x00000000.
+ */
+
+#if defined(CONFIG_MPC5200)
long int initdram (int board_type)
{
ulong dramsize = 0;
-#ifdef CONFIG_MPC5200_DDR
ulong dramsize2 = 0;
-#endif
#ifndef CFG_RAMBOOT
ulong test1, test2;
-
- /* configure SDRAM start/end */
-#if defined(CONFIG_MPC5200)
+
+ /* setup SDRAM chip selects */
*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e;/* 2G at 0x0 */
*(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000;/* disabled */
+ __asm__ volatile ("sync");
-#ifdef CONFIG_MPC5200_DDR
/* setup config registers */
- *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0x73722930;
- *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x47770000;
+ *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+ *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+ __asm__ volatile ("sync");
- /* set tap delay to 0x10 */
- *(vu_long *)MPC5XXX_CDM_PORCFG = 0x10000000;
-#else
- /* setup config registers */
- *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0xd2322800;
- *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x8ad70000;
+#if SDRAM_DDR
+ /* set tap delay */
+ *(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
+ __asm__ volatile ("sync");
#endif
-#elif defined(CONFIG_MGT5100)
- *(vu_long *)MPC5XXX_SDRAM_START = 0x00000000;
- *(vu_long *)MPC5XXX_SDRAM_STOP = 0x0000ffff;/* 2G */
- *(vu_long *)MPC5XXX_ADDECR |= (1 << 22); /* Enable SDRAM */
-
- /* setup config registers */
- *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0xc2222600;
- *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x88b70004;
-
- /* address select register */
- *(vu_long *)MPC5XXX_SDRAM_XLBSEL = 0x03000000;
-#endif
+ /* find RAM size using SDRAM CS0 only */
sdram_start(0);
test1 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
sdram_start(1);
} else {
dramsize = test2;
}
-#if defined(CONFIG_MPC5200)
- *(vu_long *)MPC5XXX_SDRAM_CS0CFG =
- (0x13 + __builtin_ffs(dramsize >> 20) - 1);
-#ifdef CONFIG_MPC5200_DDR
+
+ /* memory smaller than 1MB is impossible */
+ if (dramsize < (1 << 20)) {
+ dramsize = 0;
+ }
+
+ /* set SDRAM CS0 size according to the amount of RAM found */
+ if (dramsize > 0) {
+ *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
+ } else {
+ *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
+ }
+
+
+ /* let SDRAM CS1 start right after CS0 */
*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
+
+ /* find RAM size using SDRAM CS1 only */
sdram_start(0);
test1 = get_ram_size((ulong *)(CFG_SDRAM_BASE + dramsize), 0x80000000);
sdram_start(1);
} else {
dramsize2 = test2;
}
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG =
- dramsize + (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
-#else
- *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
-#endif
+
+ /* memory smaller than 1MB is impossible */
+ if (dramsize2 < (1 << 20)) {
+ dramsize2 = 0;
+ }
+
+ /* set SDRAM CS1 size according to the amount of RAM found */
+ if (dramsize2 > 0) {
+ *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize
+ | (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
+ } else {
+ *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
+ }
+
+#else /* CFG_RAMBOOT */
+
+ /* retrieve size of memory connected to SDRAM CS0 */
+ dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
+ if (dramsize >= 0x13) {
+ dramsize = (1 << (dramsize - 0x13)) << 20;
+ } else {
+ dramsize = 0;
+ }
+
+ /* retrieve size of memory connected to SDRAM CS1 */
+ dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF;
+ if (dramsize2 >= 0x13) {
+ dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
+ } else {
+ dramsize2 = 0;
+ }
+
+#endif /* CFG_RAMBOOT */
+
+ return dramsize + dramsize2;
+}
+
#elif defined(CONFIG_MGT5100)
- *(vu_long *)MPC5XXX_SDRAM_STOP = ((dramsize - 1) >> 15);
-#endif
-#else /* CFG_RAMBOOT */
-#ifdef CONFIG_MGT5100
+long int initdram (int board_type)
+{
+ ulong dramsize = 0;
+#ifndef CFG_RAMBOOT
+ ulong test1, test2;
+
+ /* setup and enable SDRAM chip selects */
+ *(vu_long *)MPC5XXX_SDRAM_START = 0x00000000;
+ *(vu_long *)MPC5XXX_SDRAM_STOP = 0x0000ffff;/* 2G */
*(vu_long *)MPC5XXX_ADDECR |= (1 << 22); /* Enable SDRAM */
+ __asm__ volatile ("sync");
+
+ /* setup config registers */
+ *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+ *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+
+ /* address select register */
+ *(vu_long *)MPC5XXX_SDRAM_XLBSEL = SDRAM_ADDRSEL;
+ __asm__ volatile ("sync");
+
+ /* find RAM size */
+ sdram_start(0);
+ test1 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
+ sdram_start(1);
+ test2 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
+ if (test1 > test2) {
+ sdram_start(0);
+ dramsize = test1;
+ } else {
+ dramsize = test2;
+ }
+
+ /* set SDRAM end address according to size */
+ *(vu_long *)MPC5XXX_SDRAM_STOP = ((dramsize - 1) >> 15);
+
+#else /* CFG_RAMBOOT */
+
+ /* Retrieve amount of SDRAM available */
dramsize = ((*(vu_long *)MPC5XXX_SDRAM_STOP + 1) << 15);
-#else
- dramsize = ((1 << (*(vu_long *)MPC5XXX_SDRAM_CS0CFG - 0x13)) << 20);
-#ifdef CONFIG_MPC5200_DDR
- dramsize2 = ((1 << (*(vu_long *)MPC5XXX_SDRAM_CS1CFG - 0x13)) << 20);
-#endif
-#endif
+
#endif /* CFG_RAMBOOT */
-#ifdef CONFIG_MPC5200_DDR
- dramsize += dramsize2;
-#endif
- /* return total ram size */
return dramsize;
}
+#else
+#error Neither CONFIG_MPC5200 or CONFIG_MGT5100 defined
+#endif
+
int checkboard (void)
{
#if defined(CONFIG_MPC5200)
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define SDRAM_DDR 1 /* is DDR */
+
+#if defined(CONFIG_MPC5200)
+/* Settings for XLB = 132 MHz */
+#define SDRAM_MODE 0x018D0000
+#define SDRAM_EMODE 0x40090000
+#define SDRAM_CONTROL 0x705f0f00
+#define SDRAM_CONFIG1 0x73722930
+#define SDRAM_CONFIG2 0x47770000
+#define SDRAM_TAPDELAY 0x10000000
+
+#else
+#error CONFIG_MPC5200 not defined
+#endif
--- /dev/null
+/*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define SDRAM_DDR 0 /* is SDR */
+
+#if defined(CONFIG_MPC5200)
+/* Settings for XLB = 132 MHz */
+#define SDRAM_MODE 0x00CD0000
+#define SDRAM_CONTROL 0x504F0000
+#define SDRAM_CONFIG1 0xD2322800
+#define SDRAM_CONFIG2 0x8AD70000
+
+#elif defined(CONFIG_MGT5100)
+/* Settings for XLB = 66 MHz */
+#define SDRAM_MODE 0x008D0000
+#define SDRAM_CONTROL 0x504F0000
+#define SDRAM_CONFIG1 0xC2222600
+#define SDRAM_CONFIG2 0x88B70004
+#define SDRAM_ADDRSEL 0x02000000
+
+#else
+#error Neither CONFIG_MPC5200 or CONFIG_MGT5100 defined
+#endif
emear1 = (emear1 & 0xFFFF0000) |
((new_bank0_end & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) |
((new_bank1_end & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT << 8);
-
+
mpc824x_mpc107_setreg(MEAR1, mear1);
mpc824x_mpc107_setreg(EMEAR1, emear1);
#include <common.h>
#include <command.h>
-#include <miiphy.h>
-#include <miivals.h>
#if (CONFIG_COMMANDS & CFG_CMD_MII)
+#include <miiphy.h>
+
+#define CONFIG_TERSE_MII /* XXX necessary here because "miivals.h" is missing */
#ifdef CONFIG_TERSE_MII
/*
"mii read <addr> <reg> - read MII PHY <addr> register <reg>\n"
"mii write <addr> <reg> <data> - write MII PHY <addr> register <reg>\n"
);
-#else /* CONFIG_TERSE_MII */
+
+#else /* ! CONFIG_TERSE_MII ================================================= */
+
+#include <miivals.h>
typedef struct _MII_reg_desc_t {
ushort regno;
boot_warm:
mfmsr r5 /* save msr contents */
+ /* Move CSBoot and adjust instruction pointer */
+ /*--------------------------------------------------------------*/
+
#if defined(CFG_LOWBOOT)
#if defined(CFG_RAMBOOT)
#error CFG_LOWBOOT is incompatible with CFG_RAMBOOT
stw r3, 0x4(r4) /* CS0 start */
lis r3, STOP_REG(CFG_BOOTCS_START, CFG_BOOTCS_SIZE)@h
ori r3, r3, STOP_REG(CFG_BOOTCS_START, CFG_BOOTCS_SIZE)@l
-
stw r3, 0x8(r4) /* CS0 stop */
- lis r3, 0x00047800@h
- ori r3, r3, 0x00047800@l
- stw r3, 0x300(r4) /* set timing, CS0/boot conf reg */
lis r3, 0x02010000@h
ori r3, r3, 0x02010000@l
- stw r3, 0x54(r4) /* CS0 and Boot enable, IPBI ctrl reg */
+ stw r3, 0x54(r4) /* CS0 and Boot enable */
- lis r3, lowboot_reentry@h
- ori r3, r3, lowboot_reentry@l
+ lis r3, lowboot_reentry@h /* jump from bootlow address space (0x0000xxxx) */
+ ori r3, r3, lowboot_reentry@l /* to the address space the linker used */
mtlr r3
- blr /* jump to flash based address */
+ blr
lowboot_reentry:
lis r3, START_REG(CFG_BOOTCS_START)@h
lis r3, STOP_REG(CFG_BOOTCS_START, CFG_BOOTCS_SIZE)@h
ori r3, r3, STOP_REG(CFG_BOOTCS_START, CFG_BOOTCS_SIZE)@l
stw r3, 0x50(r4) /* Boot stop */
- lis r3, 0x00047800@h
- ori r3, r3, 0x00047800@l
- stw r3, 0x300(r4) /* set timing, CS0/boot conf reg */
lis r3, 0x02000001@h
ori r3, r3, 0x02000001@l
- stw r3, 0x54(r4) /* Boot enable, CS0 disable, wait state enable */
+ stw r3, 0x54(r4) /* Boot enable, CS0 disable */
#endif /* CFG_LOWBOOT */
#if defined(CFG_DEFAULT_MBAR) && !defined(CFG_RAMBOOT)
---------------------------------------------------------------------------
Build target Flash address | BDI "go" command | Reset Vector
---------------------------------------------------------------------------
-MPC5200LITE 0xFFF00000 | 0xFFF00100 | 0xFFF00100
-MPC5200LITE_LOWBOOT 0xFF000000 | 0xFF000100 | 0x00000100
-MPC5200LITE_LOWBOOT08 0xFF800000 | 0xFF800100 | 0x00000100
+Lite5200 0xFFF00000 | 0xFFF00100 | 0xFFF00100
+Lite5200_LOWBOOT 0xFF000000 | 0xFF000100 | 0x00000100
+Lite5200_LOWBOOT08 0xFF800000 | 0xFF800100 | 0x00000100
+icecube_5200 0xFFF00000 | 0xFFF00100 | 0xFFF00100
+icecube_5200_LOWBOOT 0xFF000000 | 0xFF000100 | 0x00000100
+icecube_5200_LOWBOOT08 0xFF800000 | 0xFF800100 | 0x00000100
icecube_5200_DDR 0xFFF00000 | 0xFFF00100 | 0xFFF00100
icecube_5200_DDR_LOWBOOT 0xFF800000 | 0xFF800100 | 0x00000100
icecube_5200_DDR_LOWBOOT08 0xFF800000 | 0xFF800100 | 0x00000100
*/
#include <config.h>
+
+#ifdef CONFIG_MICROBLZE
+
#include <asm/serial_xuartlite.h>
/* FIXME: we should convert these to in32 and out32 */
{
return (IO_SERIAL_STATUS & XUL_SR_RX_FIFO_VALID_DATA);
}
+
+#endif /* CONFIG_MICROBLZE */
git.openpandora.org / pandora-u-boot.git / commitdiff