VoiceBlue: limit line lenght to 80 characters
authorLadislav Michl <Ladislav.Michl@seznam.cz>
Thu, 18 Feb 2010 02:29:39 +0000 (21:29 -0500)
committerTom Rix <Tom.Rix@windriver.com>
Sun, 7 Mar 2010 18:36:35 +0000 (12:36 -0600)
Reindent configuration header to limit line lenght to 80 characters by
removing obvious and sometimes misleading comments.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
include/configs/voiceblue.h

index 0dde65d..d46717c 100644 (file)
@@ -31,8 +31,8 @@
 #define CONFIG_OMAP1510 1              /* which is in a 5910 */
 
 /* Input clock of PLL */
-#define CONFIG_SYS_CLK_FREQ    150000000       /* 150MHz input clock */
-#define CONFIG_XTAL_FREQ       12000000
+#define CONFIG_SYS_CLK_FREQ            150000000       /* 150MHz */
+#define CONFIG_XTAL_FREQ               12000000        /*  12MHz */
 
 #undef CONFIG_USE_IRQ                  /* we don't need IRQ/FIQ stuff */
 
 /*
  * Physical Memory Map
  */
-#define CONFIG_NR_DRAM_BANKS   1               /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1           0x10000000      /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE      (64 * 1024 * 1024)
+#define CONFIG_NR_DRAM_BANKS           1
+#define PHYS_SDRAM_1                   0x10000000
+#define PHYS_SDRAM_1_SIZE              (64 * 1024 * 1024)
+#define PHYS_FLASH_1                   0x0000000
 
-#define PHYS_FLASH_1           0x00000000      /* Flash Bank #1 */
-
-#define CONFIG_SYS_LOAD_ADDR           PHYS_SDRAM_1 + 0x400000 /* default load address */
-
-/*
- * FLASH organization
- */
-#define CONFIG_SYS_FLASH_CFI                   /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER                /* Use the common driver */
-#define CONFIG_SYS_MAX_FLASH_BANKS     1
-#define CONFIG_SYS_FLASH_BASE          PHYS_FLASH_1
-
-/* FIXME: Does not work on AMD flash */
-/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 */      /* use buffered writes (20x faster) */
-#define CONFIG_SYS_MAX_FLASH_SECT      512     /* max # of sectors on one chip */
-
-#define CONFIG_SYS_MONITOR_BASE        PHYS_FLASH_1
+#define CONFIG_SYS_MONITOR_BASE                PHYS_FLASH_1
 #define CONFIG_SYS_MONITOR_LEN         (256 * 1024)
 
 /*
  * Environment settings
  */
 #define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR                (PHYS_FLASH_1 + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SIZE                (8 * 1024)
-#define CONFIG_ENV_SECT_SIZE   (64 * 1024)
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+#define CONFIG_ENV_ADDR                        (PHYS_FLASH_1 + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SIZE                        (8 * 1024)
+#define CONFIG_ENV_SECT_SIZE           (64 * 1024)
+#define CONFIG_ENV_ADDR_REDUND         (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND         CONFIG_ENV_SIZE
 
 #define CONFIG_ENV_OVERWRITE
 
 /*
  * Size of malloc() pool and stack
  */
-#define CONFIG_SYS_GBL_DATA_SIZE       128     /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE       128
 #define CONFIG_SYS_MALLOC_LEN          (4 * 1024 * 1024)
-#define CONFIG_STACKSIZE       (1 * 1024 * 1024)
-#define PHYS_SDRAM_1_RESERVED  (CONFIG_SYS_MONITOR_LEN + CONFIG_SYS_MALLOC_LEN + CONFIG_STACKSIZE)
+#define CONFIG_STACKSIZE               (1 * 1024 * 1024)
 
 /*
  * Hardware drivers
  */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    (-4)
+#define CONFIG_SYS_NS16550_CLK         (CONFIG_XTAL_FREQ)
+#define CONFIG_SYS_NS16550_COM1                OMAP1510_UART1_BASE
+
 #define CONFIG_NET_MULTI
 #define CONFIG_SMC91111
-#define CONFIG_SMC91111_BASE   0x08000300
+#define CONFIG_SMC91111_BASE           0x08000300
+
+#define CONFIG_SYS_FLASH_BASE          PHYS_FLASH_1
+#define CONFIG_SYS_MAX_FLASH_BANKS     1
+#define CONFIG_SYS_MAX_FLASH_SECT      512
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 
 #define CONFIG_HARD_I2C
 #define CONFIG_SYS_I2C_SPEED           100000
 #define CONFIG_DRIVER_OMAP1510_I2C
 
 #define CONFIG_RTC_DS1307
-#define CONFIG_SYS_I2C_RTC_ADDR        0x68
+#define CONFIG_SYS_I2C_RTC_ADDR                0x68
 
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE    (-4)
-#define CONFIG_SYS_NS16550_CLK         (CONFIG_XTAL_FREQ)      /* can be 12M/32Khz or 48Mhz  */
-#define CONFIG_SYS_NS16550_COM1        OMAP1510_UART1_BASE     /* uart1 */
 
-#define CONFIG_CONS_INDEX      1
-#define CONFIG_BAUDRATE                115200
+#define CONFIG_CONS_INDEX              1
+#define CONFIG_BAUDRATE                        115200
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
 
 
 /*
- * Command line configuration.
+ * Command line configuration
  */
 #include <config_cmd_default.h>
 
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_RUN
 
-
 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_HOSTNAME
 #define CONFIG_BOOTP_BOOTPATH
 
-
 #define CONFIG_LOOPW
 
 #define CONFIG_BOOTDELAY       3
 #define CONFIG_ZERO_BOOTDELAY_CHECK    /* allow to break in always */
-#undef  CONFIG_BOOTARGS                /* the boot command will set bootargs*/
-#define CONFIG_SYS_AUTOLOAD            "n"             /* No autoload */
+#undef  CONFIG_BOOTARGS                        /* the boot command will set bootargs*/
+#define CONFIG_SYS_AUTOLOAD            "n"
 #define CONFIG_BOOTCOMMAND     "run nboot"
 #define CONFIG_PREBOOT         "run setup"
-#define        CONFIG_EXTRA_ENV_SETTINGS                               \
-       "silent=1\0"                                            \
-       "ospart=0\0"                                            \
-       "bootfile=/boot/uImage\0"                               \
-       "setpart="                                              \
-       "if test -n $swapos; then "                             \
-               "setenv swapos; saveenv; "                      \
-               "if test $ospart -eq 0; then setenv ospart 1; else setenv ospart 0; fi; "\
-       "fi\0"                                                  \
-       "setup=setenv bootargs console=ttyS0,$baudrate "        \
-               "mtdparts=$mtdparts\0"                          \
-       "nfsargs=setenv bootargs $bootargs "                    \
+#define        CONFIG_EXTRA_ENV_SETTINGS                                       \
+       "silent=1\0"                                                    \
+       "ospart=0\0"                                                    \
+       "bootfile=/boot/uImage\0"                                       \
+       "setpart="                                                      \
+       "if test -n $swapos; then "                                     \
+               "setenv swapos; saveenv; "                              \
+               "if test $ospart -eq 0; then "                          \
+                       "setenv ospart 1; "                             \
+               "else "                                                 \
+                       "setenv ospart 0; "                             \
+               "fi; "                                                  \
+       "fi\0"                                                          \
+       "setup=setenv bootargs console=ttyS0,$baudrate "                \
+               "mtdparts=$mtdparts\0"                                  \
+       "nfsargs=setenv bootargs $bootargs "                            \
                "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
-               "nfsroot=$rootpath root=/dev/nfs\0"             \
-       "flashargs=run setpart; setenv bootargs $bootargs "     \
-               "root=mtd:data$ospart ro "                      \
-               "rootfstype=jffs2\0"                            \
-       "initrdargs=setenv bootargs $bootargs "                 \
+               "nfsroot=$rootpath root=/dev/nfs\0"                     \
+       "flashargs=run setpart; setenv bootargs $bootargs "             \
+               "root=mtd:data$ospart ro "                              \
+               "rootfstype=jffs2\0"                                    \
+       "initrdargs=setenv bootargs $bootargs "                         \
                "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \
-       "fboot=run flashargs; chpart data$ospart; fsload; bootm\0" \
-       "mboot=bootp; run initrdargs; tftp; bootm\0"            \
+       "fboot=run flashargs; chpart data$ospart; fsload; bootm\0"      \
+       "mboot=bootp; run initrdargs; tftp; bootm\0"                    \
        "nboot=bootp; run nfsargs; tftp; bootm\0"
 
 #define CONFIG_SILENT_CONSOLE          1       /* enable silent startup */
 #endif
 
 /*
- * JFFS2 partitions (mtdparts command line support)
+ * Partitions (mtdparts command line support)
  */
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_MTD_DEVICE              /* needed for mtdparts commands */
 #define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT         "nor0=omapflash.0"
-#define MTDPARTS_DEFAULT       "mtdparts=omapflash.0:256k(u-boot),64k(env),64k(r_env),16192k(data0),-(data1)"
-
+#define MTDIDS_DEFAULT         "nor0=physmap-flash.0"
+#define MTDPARTS_DEFAULT       "mtdparts=physmap-flash.0:" \
+       "256k(u-boot),64k(env),64k(r_env),16192k(data0),-(data1)"
 
 /*
  * Miscellaneous configurable options
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 #define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_LONGHELP                            /* undef to save memory         */
-#define CONFIG_SYS_PROMPT              "# "            /* Monitor Command Prompt       */
-#define CONFIG_SYS_CBSIZE              256             /* Console I/O Buffer Size      */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS             16              /* max number of command args   */
-#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
-
-#define CONFIG_SYS_MEMTEST_START       PHYS_SDRAM_1
-#define CONFIG_SYS_MEMTEST_END         PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT              "# "
+#define CONFIG_SYS_CBSIZE              256
+#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
+                                        sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS             16
+#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START       (PHYS_SDRAM_1)
+#define CONFIG_SYS_MEMTEST_END         (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - \
+       (CONFIG_SYS_MONITOR_LEN + CONFIG_SYS_MALLOC_LEN + CONFIG_STACKSIZE))
+#define CONFIG_SYS_LOAD_ADDR           (PHYS_SDRAM_1 + 0x400000)
 
-/* The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1.
+/*
+ * The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1.
  * This time is further subdivided by a local divisor.
  */
-#define CONFIG_SYS_TIMERBASE   OMAP1510_TIMER1_BASE
-#define CONFIG_SYS_PTV         7       /* 2^(PTV+1), divide by 256 */
-#define CONFIG_SYS_HZ          1000
+#define CONFIG_SYS_TIMERBASE           OMAP1510_TIMER1_BASE
+#define CONFIG_SYS_PTV                 7       /* 2^(PTV+1), divide by 256 */
+#define CONFIG_SYS_HZ                  1000
 
-#define OMAP5910_DPLL_DIV      1
-#define OMAP5910_DPLL_MUL      ((CONFIG_SYS_CLK_FREQ * \
-                                (1 << OMAP5910_DPLL_DIV)) / CONFIG_XTAL_FREQ)
+#define OMAP5910_DPLL_DIV              1
+#define OMAP5910_DPLL_MUL              \
+       ((CONFIG_SYS_CLK_FREQ * (1 << OMAP5910_DPLL_DIV)) / CONFIG_XTAL_FREQ)
 
 #define OMAP5910_ARM_PER_DIV   2       /* CKL/4 */
 #define OMAP5910_LCD_DIV       2       /* CKL/4 */