This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
prompt "MX25 board select"
optional
-config TARGET_MX25PDK
- bool "Support mx25pdk"
- select BOARD_LATE_INIT
- select CPU_ARM926EJS
- select BOARD_EARLY_INIT_F
-
config TARGET_ZMX25
bool "Support zmx25"
select BOARD_LATE_INIT
config SYS_SOC
default "mx25"
-source "board/freescale/mx25pdk/Kconfig"
source "board/syteco/zmx25/Kconfig"
endif
+++ /dev/null
-if TARGET_MX25PDK
-
-config SYS_BOARD
- default "mx25pdk"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_SOC
- default "mx25"
-
-config SYS_CONFIG_NAME
- default "mx25pdk"
-
-endif
+++ /dev/null
-MX25PDK BOARD
-M: Fabio Estevam <fabio.estevam@nxp.com>
-S: Maintained
-F: board/freescale/mx25pdk/
-F: include/configs/mx25pdk.h
-F: configs/mx25pdk_defconfig
+++ /dev/null
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
-#
-# (C) Copyright 2011 Freescale Semiconductor, Inc.
-
-obj-y := mx25pdk.o
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2009
- * Stefano Babic DENX Software Engineering sbabic@denx.de.
- *
- * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/*
- * Boot Device : one of
- * spi, sd (the board has no nand neither onenand)
- */
-BOOT_FROM sd
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type Address Value
- *
- * where:
- * Addr-type register length (1,2 or 4 bytes)
- * Address absolute address of the register
- * value value to be stored in the register
- */
-/* EIM config-CS5 init -- CPLD */
-DATA 4 0xB8002050 0x0000D843
-DATA 4 0xB8002054 0x22252521
-DATA 4 0xB8002058 0x22220A00
-
-/* DDR2 init */
-DATA 4 0xB8001004 0x0076E83A
-DATA 4 0xB8001010 0x00000204
-DATA 4 0xB8001000 0x92210000
-DATA 4 0x80000f00 0x12344321
-DATA 4 0xB8001000 0xB2210000
-DATA 1 0x82000000 0xda
-DATA 1 0x83000000 0xda
-DATA 1 0x81000400 0xda
-DATA 1 0x80000333 0xda
-
-DATA 4 0xB8001000 0x92210000
-DATA 1 0x80000400 0x12345678
-
-DATA 4 0xB8001000 0xA2210000
-DATA 4 0x80000000 0x87654321
-DATA 4 0x80000000 0x87654321
-
-DATA 4 0xB8001000 0xB2210000
-DATA 1 0x80000233 0xda
-DATA 1 0x81000780 0xda
-DATA 1 0x81000400 0xda
-DATA 4 0xB8001000 0x82216080
-DATA 4 0x43FAC454 0x00001000
-
-DATA 4 0x53F80008 0x20034000
-
-/* Enable the clocks */
-DATA 4 0x53f8000c 0x1fffffff
-DATA 4 0x53f80010 0xffffffff
-DATA 4 0x53f80014 0xfdfff
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2011 Freescale Semiconductor, Inc.
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- */
-
-#include <common.h>
-#include <init.h>
-#include <asm/global_data.h>
-#include <asm/io.h>
-#include <asm/gpio.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux-mx25.h>
-#include <asm/arch/clock.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <i2c.h>
-#include <linux/delay.h>
-#include <power/pmic.h>
-#include <fsl_pmic.h>
-#include <mc34704.h>
-
-#define FEC_RESET_B IMX_GPIO_NR(4, 8)
-#define FEC_ENABLE_B IMX_GPIO_NR(2, 3)
-#define CARD_DETECT IMX_GPIO_NR(2, 1)
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg esdhc_cfg[1] = {
- {IMX_MMC_SDHC1_BASE},
-};
-#endif
-
-/*
- * FIXME: need to revisit this
- * The original code enabled PUE and 100-k pull-down without PKE, so the right
- * value here is likely:
- * 0 for no pull
- * or:
- * PAD_CTL_PUS_100K_DOWN for 100-k pull-down
- */
-#define FEC_OUT_PAD_CTRL 0
-
-#define I2C_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \
- PAD_CTL_ODE)
-
-static void mx25pdk_fec_init(void)
-{
- static const iomux_v3_cfg_t fec_pads[] = {
- MX25_PAD_FEC_TX_CLK__FEC_TX_CLK,
- MX25_PAD_FEC_RX_DV__FEC_RX_DV,
- MX25_PAD_FEC_RDATA0__FEC_RDATA0,
- NEW_PAD_CTRL(MX25_PAD_FEC_TDATA0__FEC_TDATA0, FEC_OUT_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_FEC_TX_EN__FEC_TX_EN, FEC_OUT_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_FEC_MDC__FEC_MDC, FEC_OUT_PAD_CTRL),
- MX25_PAD_FEC_MDIO__FEC_MDIO,
- MX25_PAD_FEC_RDATA1__FEC_RDATA1,
- NEW_PAD_CTRL(MX25_PAD_FEC_TDATA1__FEC_TDATA1, FEC_OUT_PAD_CTRL),
-
- NEW_PAD_CTRL(MX25_PAD_D12__GPIO_4_8, 0), /* FEC_RESET_B */
- NEW_PAD_CTRL(MX25_PAD_A17__GPIO_2_3, 0), /* FEC_ENABLE_B */
- };
-
- static const iomux_v3_cfg_t i2c_pads[] = {
- NEW_PAD_CTRL(MX25_PAD_I2C1_CLK__I2C1_CLK, I2C_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_I2C1_DAT__I2C1_DAT, I2C_PAD_CTRL),
- };
-
- imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-
- /* Assert RESET and ENABLE low */
- gpio_direction_output(FEC_RESET_B, 0);
- gpio_direction_output(FEC_ENABLE_B, 0);
-
- udelay(10);
-
- /* Deassert RESET and ENABLE */
- gpio_set_value(FEC_RESET_B, 1);
- gpio_set_value(FEC_ENABLE_B, 1);
-
- /* Setup I2C pins so that PMIC can turn on PHY supply */
- imx_iomux_v3_setup_multiple_pads(i2c_pads, ARRAY_SIZE(i2c_pads));
-}
-
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
- PHYS_SDRAM_1_SIZE);
- return 0;
-}
-
-/*
- * Set up input pins with hysteresis and 100-k pull-ups
- */
-#define UART1_IN_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP)
-/*
- * FIXME: need to revisit this
- * The original code enabled PUE and 100-k pull-down without PKE, so the right
- * value here is likely:
- * 0 for no pull
- * or:
- * PAD_CTL_PUS_100K_DOWN for 100-k pull-down
- */
-#define UART1_OUT_PAD_CTRL 0
-
-static void mx25pdk_uart1_init(void)
-{
- static const iomux_v3_cfg_t uart1_pads[] = {
- NEW_PAD_CTRL(MX25_PAD_UART1_RXD__UART1_RXD, UART1_IN_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_UART1_TXD__UART1_TXD, UART1_OUT_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_UART1_RTS__UART1_RTS, UART1_OUT_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_UART1_CTS__UART1_CTS, UART1_IN_PAD_CTRL),
- };
-
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-}
-
-int board_early_init_f(void)
-{
- mx25pdk_uart1_init();
-
- return 0;
-}
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- return 0;
-}
-
-int board_late_init(void)
-{
- struct pmic *p;
- int ret;
-
- mx25pdk_fec_init();
-
- ret = pmic_init(I2C_0);
- if (ret)
- return ret;
-
- p = pmic_get("FSL_PMIC");
- if (!p)
- return -ENODEV;
-
- /* Turn on Ethernet PHY and LCD supplies */
- pmic_reg_write(p, MC34704_GENERAL2_REG, ONOFFE | ONOFFA);
-
- return 0;
-}
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-int board_mmc_getcd(struct mmc *mmc)
-{
- /* Set up the Card Detect pin. */
- imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX25_PAD_A15__GPIO_2_1, 0));
-
- gpio_direction_input(CARD_DETECT);
- return !gpio_get_value(CARD_DETECT);
-}
-
-int board_mmc_init(struct bd_info *bis)
-{
- static const iomux_v3_cfg_t sdhc1_pads[] = {
- NEW_PAD_CTRL(MX25_PAD_SD1_CMD__SD1_CMD, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_SD1_CLK__SD1_CLK, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_SD1_DATA0__SD1_DATA0, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_SD1_DATA1__SD1_DATA1, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_SD1_DATA2__SD1_DATA2, NO_PAD_CTRL),
- NEW_PAD_CTRL(MX25_PAD_SD1_DATA3__SD1_DATA3, NO_PAD_CTRL),
- };
-
- imx_iomux_v3_setup_multiple_pads(sdhc1_pads, ARRAY_SIZE(sdhc1_pads));
-
- /*
- * Set the eSDHC1 PER clock to the maximum frequency lower than or equal
- * to 50 MHz that can be obtained, which requires to use UPLL as the
- * clock source. This actually gives 48 MHz.
- */
- imx_set_perclk(MXC_ESDHC1_CLK, true, 50000000);
- esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC1_CLK);
- return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
-}
-#endif
-
-int checkboard(void)
-{
- puts("Board: MX25PDK\n");
-
- return 0;
-}
-
-/* Lowlevel init isn't used on mx25pdk, so just provide a dummy one here */
-void lowlevel_init(void) {}
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_MX25=y
-CONFIG_SYS_TEXT_BASE=0x81200000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x60000
-CONFIG_TARGET_MX25PDK=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx25pdk/imximage.cfg"
-CONFIG_DEFAULT_FDT_FILE="imx25-pdk.dtb"
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_FUSE=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_DATE=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_DOS_PARTITION=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_FSL_ESDHC_IMX=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_FS_EXT4=y
-CONFIG_FS_FAT=y
-CONFIG_OF_LIBFDT=y
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2011 Freescale Semiconductor, Inc.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/imx-regs.h>
-
-/* High Level Configuration Options */
-
-#define CONFIG_SYS_TEXT_BASE 0x81200000
-#define CONFIG_SYS_FSL_CLK
-
-#define CONFIG_SYS_TIMER_RATE 32768
-#define CONFIG_SYS_TIMER_COUNTER \
- (&((struct gpt_regs *)IMX_GPT1_BASE)->counter)
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-#define CONFIG_MACH_TYPE MACH_TYPE_MX25_3DS
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
-
-/* Physical Memory Map */
-
-#define PHYS_SDRAM_1 0x80000000
-#define PHYS_SDRAM_1_SIZE (64 * 1024 * 1024)
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR IMX_RAM_BASE
-#define CONFIG_SYS_INIT_RAM_SIZE IMX_RAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/* Memory Test */
-
-/* Serial Info */
-#define CONFIG_MXC_UART_BASE UART1_BASE
-
-/* No NOR flash present */
-
-/* U-Boot general configuration */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/* Ethernet */
-#define CONFIG_FEC_MXC
-#define CONFIG_FEC_MXC_PHYADDR 0x1f
-
-/* ESDHC driver */
-#define CONFIG_SYS_FSL_ESDHC_ADDR IMX_MMC_SDHC1_BASE
-#define CONFIG_SYS_FSL_ESDHC_NUM 1
-
-/* PMIC Configs */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_FSL
-#define CONFIG_POWER_FSL_MC34704
-#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x54
-
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-
-/* RTC */
-#define CONFIG_RTC_IMXDI
-
-/* Fuse API support */
-#define CONFIG_FSL_IIM
-
-/* Ethernet Configs */
-
-
-#define CONFIG_LOADADDR 0x81000000 /* loadaddr env var */
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "script=boot.scr\0" \
- "image=zImage\0" \
- "console=ttymxc0\0" \
- "splashpos=m,m\0" \
- "fdt_high=0xffffffff\0" \
- "initrd_high=0xffffffff\0" \
- "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
- "fdt_addr=0x82000000\0" \
- "boot_fdt=try\0" \
- "ip_dyn=yes\0" \
- "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
- "mmcpart=1\0" \
- "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
- "update_sd_firmware_filename=u-boot.imx\0" \
- "update_sd_firmware=" \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "if mmc dev ${mmcdev}; then " \
- "if ${get_cmd} ${update_sd_firmware_filename}; then " \
- "setexpr fw_sz ${filesize} / 0x200; " \
- "setexpr fw_sz ${fw_sz} + 1; " \
- "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
- "fi; " \
- "fi\0" \
- "mmcargs=setenv bootargs console=${console},${baudrate} " \
- "root=${mmcroot}\0" \
- "loadbootscript=" \
- "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
- "loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
- "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0" \
- "netargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
- "netboot=echo Booting from net ...; " \
- "run netargs; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${image}; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootz ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootz; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootz; " \
- "fi;\0"
-
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loadimage; then " \
- "run mmcboot; " \
- "else run netboot; " \
- "fi; " \
- "fi; " \
- "else run netboot; fi"
-
-/* Miscellaneous configurable options */
-
-#endif /* __CONFIG_H */
git.openpandora.org / pandora-u-boot.git / commitdiff