/cpu CPU specific files
/arm720t Files specific to ARM 720 CPUs
/arm920t Files specific to ARM 920 CPUs
- /at91rm9200 Files specific to Atmel AT91RM9200 CPU
+ /at91 Files specific to Atmel AT91RM9200 CPU
/imx Files specific to Freescale MC9328 i.MX CPUs
/s3c24x0 Files specific to Samsung S3C24X0 CPUs
/arm925t Files specific to ARM 925 CPUs
must be defined, to setup the maximum idle timeout for
the SMC.
+- Pre-Console Buffer:
+ Prior to the console being initialised (i.e. serial UART
+ initialised etc) all console output is silently discarded.
+ Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
+ buffer any console messages prior to the console being
+ initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
+ bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
+ a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
+ bytes are output before the console is initialised, the
+ earlier bytes are discarded.
+
+ 'Sane' compilers will generate smaller code if
+ CONFIG_PRE_CON_BUF_SZ is a power of 2
+
- Boot Delay: CONFIG_BOOTDELAY - in seconds
Delay before automatically booting the default image;
set to -1 to disable autoboot.
or CONFIG_VIDEO_SED13806_16BPP
CONFIG_FSL_DIU_FB
- Enable the Freescale DIU video driver. Reference boards for
+ Enable the Freescale DIU video driver. Reference boards for
SOCs that have a DIU should define this macro to enable DIU
support, and should also define these other macros:
kernel. Needed for UBI support.
- SPL framework
- CONFIG_SPL
- Enable building of SPL globally.
+ CONFIG_SPL
+ Enable building of SPL globally.
- CONFIG_SPL_TEXT_BASE
- TEXT_BASE for linking the SPL binary.
+ CONFIG_SPL_TEXT_BASE
+ TEXT_BASE for linking the SPL binary.
- CONFIG_SPL_LDSCRIPT
- LDSCRIPT for linking the SPL binary.
+ CONFIG_SPL_LDSCRIPT
+ LDSCRIPT for linking the SPL binary.
- CONFIG_SPL_LIBCOMMON_SUPPORT
- Support for common/libcommon.o in SPL binary
+ CONFIG_SPL_LIBCOMMON_SUPPORT
+ Support for common/libcommon.o in SPL binary
- CONFIG_SPL_LIBDISK_SUPPORT
- Support for disk/libdisk.o in SPL binary
+ CONFIG_SPL_LIBDISK_SUPPORT
+ Support for disk/libdisk.o in SPL binary
- CONFIG_SPL_I2C_SUPPORT
- Support for drivers/i2c/libi2c.o in SPL binary
+ CONFIG_SPL_I2C_SUPPORT
+ Support for drivers/i2c/libi2c.o in SPL binary
- CONFIG_SPL_GPIO_SUPPORT
- Support for drivers/gpio/libgpio.o in SPL binary
+ CONFIG_SPL_GPIO_SUPPORT
+ Support for drivers/gpio/libgpio.o in SPL binary
- CONFIG_SPL_MMC_SUPPORT
- Support for drivers/mmc/libmmc.o in SPL binary
+ CONFIG_SPL_MMC_SUPPORT
+ Support for drivers/mmc/libmmc.o in SPL binary
- CONFIG_SPL_SERIAL_SUPPORT
- Support for drivers/serial/libserial.o in SPL binary
+ CONFIG_SPL_SERIAL_SUPPORT
+ Support for drivers/serial/libserial.o in SPL binary
- CONFIG_SPL_SPI_FLASH_SUPPORT
- Support for drivers/mtd/spi/libspi_flash.o in SPL binary
+ CONFIG_SPL_SPI_FLASH_SUPPORT
+ Support for drivers/mtd/spi/libspi_flash.o in SPL binary
- CONFIG_SPL_SPI_SUPPORT
- Support for drivers/spi/libspi.o in SPL binary
+ CONFIG_SPL_SPI_SUPPORT
+ Support for drivers/spi/libspi.o in SPL binary
- CONFIG_SPL_FAT_SUPPORT
- Support for fs/fat/libfat.o in SPL binary
+ CONFIG_SPL_FAT_SUPPORT
+ Support for fs/fat/libfat.o in SPL binary
- CONFIG_SPL_LIBGENERIC_SUPPORT
- Support for lib/libgeneric.o in SPL binary
+ CONFIG_SPL_LIBGENERIC_SUPPORT
+ Support for lib/libgeneric.o in SPL binary
Modem Support:
--------------
and RPXsuper) to be able to adjust the position of
the IMMR register after a reset.
+- CONFIG_SYS_CCSRBAR_DEFAULT:
+ Default (power-on reset) physical address of CCSR on Freescale
+ PowerPC SOCs.
+
+- CONFIG_SYS_CCSRBAR:
+ Virtual address of CCSR. On a 32-bit build, this is typically
+ the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
+
+ CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
+ for cross-platform code that uses that macro instead.
+
+- CONFIG_SYS_CCSRBAR_PHYS:
+ Physical address of CCSR. CCSR can be relocated to a new
+ physical address, if desired. In this case, this macro should
+ be set to that address. Otherwise, it should be set to the
+ same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
+ is typically relocated on 36-bit builds. It is recommended
+ that this macro be defined via the _HIGH and _LOW macros:
+
+ #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
+ * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
+
+- CONFIG_SYS_CCSRBAR_PHYS_HIGH:
+ Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
+ either 0 (32-bit build) or 0xF (36-bit build). This macro is
+ used in assembly code, so it must not contain typecasts or
+ integer size suffixes (e.g. "ULL").
+
+- CONFIG_SYS_CCSRBAR_PHYS_LOW:
+ Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
+ used in assembly code, so it must not contain typecasts or
+ integer size suffixes (e.g. "ULL").
+
+- CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
+ If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
+ forced to a value that ensures that CCSR is not relocated.
+
- Floppy Disk Support:
CONFIG_SYS_FDC_DRIVE_NUMBER
bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
- ethprime - When CONFIG_NET_MULTI is enabled controls which
- interface is used first.
+ ethprime - controls which interface is used first.
- ethact - When CONFIG_NET_MULTI is enabled controls which
- interface is currently active. For example you
- can do the following
+ ethact - controls which interface is currently active.
+ For example you can do the following
=> setenv ethact FEC
=> ping 192.168.0.1 # traffic sent on FEC
git.openpandora.org / pandora-u-boot.git / blobdiff