[SCSI] qla2xxx: Correctly read sfp single byte mailbox register.

When reading a single byte using the READ SFP mailbox command, the
single byte of data is returned in MB[1] and not MB[8].

The reason that MB[8] was being used is that the spec was unclear
as it evolved over time; and we have not needed to read a single
byte until recently.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add qla82xx_rom_unlock() function.

Encapsulate the unlocking of the ROM lock in a function for better
code readability.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Log if qla82xx firmware fails to load from flash.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Use passed in host to initialize local scsi_qla_host in queuecommand function

Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Correct buffer start in edc sysfs debug print.

The debug print prints the first byte of the buffer which is buf[8].

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Update firmware version after flash update for ISP82xx.

The driver keeps a copy of the fw_version within the ha structure.
For ISP82xx, this local copy doesn't get updated, and as a result,
the old firmware version ends up getting displayed. This patch fixes
this issue.

Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Fix hang during driver unload when vport is active.

Bumping ref count during fc_vport_terminate() was the cause. vport
delete would wait for ref count to drop to zero and that would never
happen.

Cc: stable@kernel.org
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Properly set the dsd_list_len for dsd_chaining in cmd type 6.

The firmware spec has the fcp_data_dseg_len defined as a 32-bit
value, while the corresponding field in the driver structure has
it defined as a 16-bit value.

Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Fix virtual port failing to login after chip reset.

This patch ensures qla82xx_watchdog is not being run for the vport. It also
makes sure that beacon ON is not done for the vport, as it will lead to the
waking up of the dpc thread again and again.

Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Fix vport delete hang when logins are outstanding.

Timer is required to flush out entries that may be present in work queues.

Cc: stable@kernel.org
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: Change memset using sizeof(ptr) to sizeof(*ptr)

Not at all sure this is correct or appropriate to change,
but this seems odd.

Found via coccinelle script

@@
type T;
T* ptr;
expression E1;
@@

* memset(E1, 0, sizeof(ptr));

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] ipr: Rate limit DMA mapping errors

I noticed a stream of errors from the IPR driver while doing
IOMMU fault injection. Rate limit the errors so we don't clog
up the console and logfiles.

Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: add P2000 to list of shared SAS devices

Signed-off-by: Scott Teel <scott.stacy.teel@hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: do not attempt PCI power management reset method if we know it won't work.

Just go straight to the soft-reset method instead.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: remove superfluous sleeps around reset code

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: do soft reset if hard reset is broken

on driver load, if reset_devices is set, and the hard reset
attempts fail, try to bring up the controller to the point that
a command can be sent, and send it a soft reset command, then
after the reset undo whatever driver initialization was done to get
it to the point to take a command, and re-do it after the reset.

This is to get kdump to work on all the "non-resettable" controllers
(except 64xx controllers which can't be reset due to the potentially
shared cache module.)

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: use new doorbell-bit-5 reset method

The bit-2-doorbell reset method seemed to cause (survivable) NMIs
on some systems and (unsurvivable) IOCK NMIs on some G7 servers.
Firmware guys implemented a new doorbell method to alleviate these
problems triggered by bit 5 of the doorbell register.  We want to
use it if it's available.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: remove atrophied hpsa_scsi_setup function

hpsa_scsi_setup at one time contained enough code to justify
its existence, but that time has passed.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: clarify messages around reset behavior

When waiting for the board to become "not ready"
don't print a message saying "waiting for board to
become ready" (possibly followed by a message saying
"failed waiting for board to become not ready".  Instead,
it should be "waiting for board to reset" and "failed
waiting for board to reset."

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: increase time to wait for board reset

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: factor out irq request code

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: factor out cmd pool allocation functions

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: wait longer for no-op to complete after resetting controller

This is to avoid the usual two or three messages about the command
timing out.  We're obviously not waiting long enough.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: do a better job of detecting controller reset failure

Detect failure of controller reset by noticing if the 32 bytes of
"driver version" we store on the hardware in the config table
fail to get zeroed out.  Previously we noticed if the controller
did not transition to "simple mode", but this did not detect reset
failure if the controller was already in simple mode prior to
the reset attempt (e.g. due to module parameter hpsa_simple_mode=1).

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: delete old unused padding garbage

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: remove unused parameter from hpsa_complete_scsi_command()

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: add readl after writel in interrupt mask setting code

This is to ensure the board interrupts are really off when
these functions return.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] hpsa: do readl after writel in main i/o path to ensure commands don't get lost.

Apparently we've been doin it rong for a decade, but only lately do we
run into problems.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] mptsas: Fix annoying warning

Shut up

drivers/message/fusion/mptsas.c: In function 'mptsas_event_process':
drivers/message/fusion/mptsas.c:5015: warning: unused variable 'log_info'

for configs with CONFIG_SCSI_MPT2SAS_LOGGING unset.

Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] tcm_fc: Adding FC_FC4 provider (tcm_fc) for FCoE target (TCM - target core) support

This is a comprehensive patch for FC-FC4 provider. tcm_fc is a FC-FC4
provider which glues target core (TCM) with Fiber channel library
(libfc). tcm_fc uses existing FC4 provider hooks from Fiber channel
library. This Fiber channel library is used by FCoE (transport - FC
over Ethernet) protocol driver as well.

Combination of modules such as Fiber channel library, tcm_fc, TCM
target core, and FCoE protocol driver enables functional FCoE target.

This patch includes initial commit for tcm_fc plus additional
enhancement, bug fixes.

This tcm_fc module essentially contains 3 entry points such as "prli",
"prlo", "recv".  When process login request (ELS_PRLI) request is
received, Fiber channel library (libfc) module calls passive providers
(FC-FC4, tcm_fc) (if any registered) "prli" function. Likewise when
LOGO request is received, "prlo" function of passive provider is
invoked by libfc.  For all other request (e.g. any read/write, task
management, LUN inquiry commands), "recv" function of passiver
provider is invoked by libfc. Those passive providers "prli, prlo,
recv" functions interact with TCM target core for requested operation.

This module was primarily developed by "Joe Eykholt" and there were
significant contributions from the people listed under signed-off.

Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] be2iscsi: update version

Bump version.

Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] be2iscsi: fix chip cleanup

This patch fixes a bug where proper queue id's were not passed to
chip for cleanup.

Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] be2iscsi: fix boot hang due to interrupts not getting rearmed

This patch fixes a bug where the interrupts were not rearmed if
the Interrupt Mask was enabled. This patch checks for Interrupt mask
enabled and still rearms interrupt generation even if the Interrupt
mask was enabled

Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] arcmsr: simplify assumptions in dma_alloc_coherent()

The code currently computes an offset into a dma_alloc_coherent() area
on the assumption that the alignment is imprecise.  In fact, the API
guarantees PAGE_SIZE alignment, so the offset calculation is always
zero: remove it.

[jejb: make description actually descriptive]
Signed-off-by: Tomas henzl <thenzl@redhat.com>
Acked-by: Nick Cheng<nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] arcmsr: simplify some double loops in sleeping functions

I removed outer loops in ...wait_msgint_ready the sleeptime and
retrycount are in fact never changed so I changed them into
defines. In arcmsr_flush_hba_cache is a loop removed, which printed
the same printk 100 times, one line in log is enough I think.  The
arcmsr_sleep_for_bus_reset has lost a functionality with the latest
patches, The only thing the function does is a long sleep, so it's
replaced with a ssleep.

[jejb: checkpatch fixes]
Signed-off-by: Tomas henzl <thenzl@redhat.com>
Acked-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] bnx2fc: setup em for npiv port

Use fc_exch_mgr_list_clone to setup em for npiv port.

Also remove redundant vport and lport initializations.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] iterate over devices individually for /proc/scsi/scsi

On systems with very large numbers (> 1600 or so) of SCSI devices,
cat /proc/scsi/scsi ends up failing with -ENOMEM. This is due to
the show routine simply iterating over all of the devices with
bus_for_each_dev(), and trying to dump all of them into the buffer
at the same time. On my test system (using scsi_debug with 4064 devices),
the output ends up being ~ 632k, far more than kmalloc will typically allow.

This patch defines its own seq_file opreations to iterate over the scsi
devices.The result is that each show() operation only dumps ~ 180 bytes
into the buffer at a time so we don't run out of memory.

If the "Attached devices" header isn't required, we can dump the
sfile->private bit completely.

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] ipr: Driver version 2.5.2

Bump the driver version.

Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] ibmvscsi: Improve CRQ reset reliability

This patch fixes an issue seen where an event occurs
which causes the ibmvscsi driver to reset its CRQ. Upon
re-registering its CRQ, it receives H_CLOSED, indicating
the Virtual I/O Server is not yet ready to receive commands.
This resulted in the ibmvscsi driver essentially offlining
the adapter and not recovering. The fix is to re-enable
our interrupt so that when the Virtual I/O server is ready
and sends a CRQ init, we will be able to receive it and
resume initialization of the VSCSI adapter.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] ipr: increase the dump size for 64 bit adapters

Currently the size of the dump generated by the driver is limited
in 4MB, which is insufficient to gather much useful data from the
new 64 bit adapters.

This patch makes the needed changes to increase the dump limit
for the 64 bit adapters to 32MB, or even to a bigger value in the
future, but keeping the current limitations for the legacy 32 bit
adapters.

Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] mvsas: add support for Task collector mode and fixed relative bugs

1. Add support for Task collector mode.
2. Fixed relative collector mode bug:
   - I/O failed when disks is on two ports
   - system hang when hotplug disk
   - system hang when unplug disk during run IO
3. Unlock ap->lock within .lldd_execute_task for direct mode to
   improve performance

Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] mvsas: add support for Marvell 88SE9445/88SE9485

This is support for Marvell 88SE9445/88SE9485 SAS/SATA HBA, which
is based on Marvell 88SE9480.

Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] scsi_dh_alua: Attach to UNAVAILABLE/OFFLINE AAS devices

The SCSI ALUA handler currently fails to attach to devices
reporting an UNAVAILABLE/OFFLINE AAS. But given that an
UNAVAILABLE/OFFLINE AAS can transition to other states
like ACTIVE/OPTIMIZED, ACTIVE/NON-OPTIMIZED, etc. as per
SPC4, this ALUA handler behavior should be rectified so
as to attach to devices which also report an
UNAVAILABLE/OFFLINE AAS.

Signed-off-by: Martin George <marting@netapp.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] mptfusion: Bump version 3.4.19

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] mptfusion: Adding inline data padding support for TAPE drive.

Adding support for inline data padding for TAPE drive when running U320.

[jejb: whitespace fixes]
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] mptfusion: Remove debug print from mptscsih_qcmd()

Remove debug print from mptscsih_qcmd function call.
This debug print cause flood of prints and difficult to debug other issues.

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] bnx2fc: increase cleanup wait time

FW may take more time cleaning up IOs issued to multiple targets.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] bnx2fc: Do not use HBA_DBG macro when lport is not available

Use MISC_DBG instead.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] bnx2fc: call scsi_done if session goes to not ready from ready

If the session is not ready yet, we ask the SCSI-ml to retry. However, if the
session is just uploaded, we should not retry, but instead call scsi_done to
fail the IO.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] bnx2fc: Release the reference to hba only after the interface is destroyed

Prematurely decrementing the reference may lead to cmd_mgr becoming NULL with
the cmds are still active.

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] scsi_transport_fc: Fix deadlock during fc_remove_host

Creating and destroying fcoe interface in a tight loop leads to a system
deadlock with the following call traces:

Call Trace:
[<ffffffff814f4b3d>] schedule_timeout+0x1fd/0x2c0
[<ffffffff814f469f>] ? wait_for_common+0x4f/0x190
[<ffffffff814f469f>] ? wait_for_common+0x4f/0x190
[<ffffffff814f4737>] wait_for_common+0xe7/0x190
[<ffffffff81042fa0>] ? default_wake_function+0x0/0x20
[<ffffffff81082c2d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff814f48bd>] wait_for_completion+0x1d/0x20
[<ffffffff81066d90>] flush_workqueue+0x290/0x5f0
[<ffffffff81066b00>] ? flush_workqueue+0x0/0x5f0
[<ffffffff81067148>] destroy_workqueue+0x38/0x340
[<ffffffffa0260289>] fc_remove_host+0x1b9/0x1f0 [scsi_transport_fc]
[<ffffffffa02ed195>] bnx2fc_if_destroy+0xc5/0x1f0 [bnx2fc]
[<ffffffffa02ed33a>] bnx2fc_destroy+0x7a/0x100 [bnx2fc]
[<ffffffffa02c789b>] fcoe_transport_destroy+0x9b/0x1b0 [libfcoe]
[<ffffffff81069ec2>] param_attr_store+0x52/0x80
[<ffffffff81069976>] module_attr_store+0x26/0x30
[<ffffffff8119e726>] sysfs_write_file+0xe6/0x170
[<ffffffff81134710>] vfs_write+0xd0/0x1a0
[<ffffffff811348e4>] sys_write+0x54/0xa0
[<ffffffff81002e02>] system_call_fastpath+0x16/0x1b
Call Trace:
[<ffffffff81074865>] async_synchronize_cookie_domain+0x75/0x120
[<ffffffff8106caa0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff81074925>] async_synchronize_cookie+0x15/0x20
[<ffffffff8107494c>] async_synchronize_full+0x1c/0x40
[<ffffffffa0057466>] sd_remove+0x36/0xc0 [sd_mod]
[<ffffffff81358a75>] __device_release_driver+0x75/0xe0
[<ffffffff81358bef>] device_release_driver+0x2f/0x50
[<ffffffff81357aee>] bus_remove_device+0xbe/0x120
[<ffffffff813553ef>] device_del+0x12f/0x1e0
[<ffffffff8137454d>] __scsi_remove_device+0xbd/0xc0
[<ffffffff81374585>] scsi_remove_device+0x35/0x50
[<ffffffff813746a7>] __scsi_remove_target+0xe7/0x110
[<ffffffff81374730>] ? __remove_child+0x0/0x30
[<ffffffff81374753>] __remove_child+0x23/0x30
[<ffffffff81354a2c>] device_for_each_child+0x4c/0x80
[<ffffffff81374703>] scsi_remove_target+0x33/0x60
[<ffffffffa02622c6>] fc_starget_delete+0x26/0x30 [scsi_transport_fc]
[<ffffffffa026271a>] fc_rport_final_delete+0xaa/0x200 [scsi_transport_fc]
[<ffffffff8106585a>] process_one_work+0x1aa/0x540
[<ffffffff810657eb>] ? process_one_work+0x13b/0x540
[<ffffffffa0262670>] ? fc_rport_final_delete+0x0/0x200 [scsi_transport_fc]
[<ffffffff81067ac9>] worker_thread+0x179/0x410
[<ffffffff81067950>] ? worker_thread+0x0/0x410
[<ffffffff8106c546>] kthread+0xb6/0xc0
[<ffffffff8103879b>] ? finish_task_switch+0x4b/0xe0
[<ffffffff81003ca4>] kernel_thread_helper+0x4/0x10
[<ffffffff814f7994>] ? restore_args+0x0/0x30
[<ffffffff8106c490>] ? kthread+0x0/0xc0
[<ffffffff81003ca0>] ? kernel_thread_helper+0x0/0x10

fc_remove_host() waits for flushing the workqueue, but it is stuck at flushing
the first work. The first work doesnt complete, because it is waiting for async
layer to complete the IOs. The async layer cannot complete the IO as the
terminate_rport_io for the second work was not called, which will be called
only when the first work completes. Hence the deadlock.  To resolve this
deadlock, the workqueue allocation has been modified from
create_singlethread_workqueue() to alloc_workqueue().

In addition, fc_terminate_rport_io() should be called before the
scsi_flush_work() to avoid the similar deadlock as above.

scsi fc alloc queue. move terminate rport io before flush

Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] lpfc 8.3.23: Update driver version to 8.3.23

Update driver version to 8.3.22

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] lpfc 8.3.23: BSG additions and fixes

- Fixed the mixed declarations and codes which violate ISO C90
   (declarations in subsections that assign at declaration)
- Add BSG data transfer size protection in mailbox command pass-through path
- Invoke BSG job_done while holding spinlock to fix deadlock
- Added support for checking SLI_CONFIG subcommands
- Fixed bug in BSG mailbox size check to non-embedded external buffer

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] lpfc 8.3.23: Fixes related to new hardware

Fixes related to new hardware

- Restrict driver to look at BAR2 or BAR4 only for if_type 0.
- Allow SLI4 with FCOE_MODE not set for new SLI4 FC adapters.
- Add Temporary RPI field to the ELS request WQE.
- Do not override CT field in issue_els_flogi for SLI4 IF type 2
- For RQ_CREATE_V2 mbx cmd: fill in the rqe_size and page_size for RQ_CREATE.

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] lpfc 8.3.23: Miscellaneous fixes

Miscellaneous fixes

- Do not limit RPI Count to a minimum of 64
- Fix FCFI incorrect on received unsolicited frames.
- Save the FCFI returned in the REG_FCFI mailbox command if it was successful.
- Fixed Vports not sending FDISC after lips.
- Align based on the SLI4_PAGE_SIZE.
- Fixed double byte swap on received RRQ.
- Fixed mask size for the wq_id mask from 0x7F to 0x7FFF.
- Clear FC_FABRIC flag when NPIV LOGO completes (and add a log message).
- Modified driver to skip round robin only when ulpStatus==LOCAL_REJECT
  and word4=SEQUENCE_TIMEOUT to prevent FLOGI to disconnected FCF.
- Don't add rport if driver unloading

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] lpfc 8.3.23: Debugfs enhancements

Debugfs enhancements

- Added iDiag support for new adapters.
- Added queue entry access methods.
- Fix host/port index in decimal
- Added Doorbell register access methods.

Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] bfa: Move debugfs initialization before bfa init.

Move the initialization of debugfs before bfa init, to enable us to
collect driver/firmware traces if init fails.  Also add a printk to
display message on bfa_init failure.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] bfa: firmware download fix

This patch includes fixes for two issues releated to firmware download
implementation: 1) Merged memory leak fix provided by Jesper Juhl
<jj@chaosbits.net>. Basically we need to call release_firmware() after
request_firmware(). 2) fixed issues with the firmware download interface
as pointed out by Rolf Eike Beer <eike@sf-mail.de> in linux-scsi. Rearranged
the code and fixed related function protypes.

Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] ipr: improve interrupt service routine performance

During performance testing on P7 machines it was observed that the interrupt
service routine was doing unnecessary MMIO operations.

This patch rearranges the logic of the routine and moves some of the code out
of the main routine.  The result is that there are now fewer MMIO operations in
the performance path of the code.

As a result of the above change, an existing condition was exposed where the
driver could get an "unexpected" hrrq interrupt.  The original code would flag
the interrupt as unexpected and then reset the adapter.  After further analysis
it was confirmed that this condition can occasionally occur and that the
interrupt can safely be ignored.  Additional code in this patch detects this
condition, clears the interrupt and allows the driver to continue without
resetting the adapter.

Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] scsi_dh_rdac : decide whether to send mode select based on operating mode

Based on the operating modes, handler decides whether to send mode
select or not. Purpose here is to reduce io-shipping as much as
possible whenever there is an option.

Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Yanling Qi <yanling.qi@lsi.com>
Reviewed-by: Sudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: Bob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: Vijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] scsi_dh_rdac : Detect the different RDAC operating modes

This patch detects different operating RDAC modes during the
discovery. It also collects the information about the preferred path.

Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Yanling Qi <yanling.qi@lsi.com>
Reviewed-by: Sudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: Bob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: Vijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] scsi_dh_rdac : Add definitions for different RDAC operating modes

This patch adds definitions to support for different operating modes
for LSI rdac storage.  Currently, rdac support 3 operation modes.

1. RDAC mode(legacy)
2. AVT mode
3. IOSHIP mode

These definitions are used while activating the path(rdac_activate).

Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Yanling Qi <yanling.qi@lsi.com>
Reviewed-by: Sudhir Dachepalli <Sudhir.Dachepalli@lis.com>
Reviewed-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Reviewed-by: Bob Stankey <Robert.Stankey@lsi.com>
Reviewed-by: Vijay Chauhan <Vijay.Chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] ipr: remove unneeded volatile declarations

This patch removes three volatile declarations based on some feedback and code
analysis.

Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] mpt2sas : WarpDrive New product SSS6200 support added

This patch has Support for the new solid state device product SSS6200
from LSI and relavent features w.r.t SSS6200.

The major feature added in this driver is supporting Direct-I/O to the
SSS6200 storage.There are some additional changes done to avoid exposing
the RAID member disks to the OS and hiding/exposing drives based on the
OEM Specific Flag in Manufacturing Page10 (this is required to handle
specific changes in the SSS6200 firmware).

Each and every changes are listed below.
1. Hiding IR related messages.
For SSS6200, the driver is modified not to print IR related events.
Even if the debugging is enabled the IR related messages will not be displayed.
In some places if there is a need to display a message related to IR the
string "IR" is replaced with string "DD" and the string "volume" is replaced
with "direct drive". But the function names are not changed hence there are
some places where the reference to volume can be seen if debug level is set.

2. Removed RAID transport support
In Linux the user can retrieve RAID volume information from the sysfs directory.
This support is removed for SSS6200.

3. Direct I/O support.
The driver tries to enable direct I/O when a volume is reported to the driver
by the firmware through IRCC events and the driver does this just before
reporting to the OS, hence all the OS issued I/O can go through direct path
if they can, The first validation is to see whether the manufacturing page10
flag is set to expose all drives always. If that is set, the driver will not
enable direct I/O and displays the message "DDIO" is disabled globally as
drives are exposed. The driver checks whether there is more than one volume
in the controller, if so the direct I/O will be disabled globally for all
volumes in the controller and the message displayed will be "DDIO is disabled
globally as number of drives > 1.
If retrieving number of PD is failed the driver will not enable direct I/O
and displays the message Failure in computing number of drives DDIO disabled.
If memory allocation for RAIDVolumePage0 is failed, the driver will not enable
direct I/O and displays the message Memory allocation failure for
RVPG0 DDIO disabled.  If retrieving RAIDVolumePage0 is failed the driver will
not enable direct I/O and displays the message Failure in retrieving
RVPG0 DDIO disabled

If the number of PD in a volume is greater than 8, then the direct I/O will
be disabled.
If any of individual drives handle retrieval is failed then the DD-IO will
be disabled.
If the volume is not RAID0 or if the block size is not 512 then the DD-IO will
be disabled.
If the volume size is greater than 2TB then the DD-IO will be disabled.
If the driver is not able to find a valid stripe exponent using the configured
stripe size then the DD-IO will be disabled

When the DD-IO is enabled the driver will check every I/O request issued to
the storage and checks whether the request is either
READ6/WRITE6/READ10/WRITE10, if it is and if the complete I/O transfer
is within a stripe size then the I/O is redirected to
the drive directly instead of the volume.

On completion of every I/O, if the completion is failure means if the reply
is address reply with a reply frame associated with it, then the type of I/O
will be checked, if the I/O is direct then the I/O will be retried to
the volume once.

Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Reviewed-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] fusion: do not check serial_number in the abort handler

The SCSI midlayer stops all command processing when in error handling, which
means there is no chance for command reuse when the abort handler is called.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] mpt2sas: do not check serial_number in the abort handler

The SCSI midlayer stops all command processing when in error handling, which
means there is no chance for command reuse when the abort handler is called.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] usb-storage: do not increment cmd->serial_number

The isd200 sub-driver increments the command serial number despite not
using it at all in it's routine for sending internal scsi commands.
Remove the increment to prepare for removing the serial_number field.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] remove cmd->serial_number litter

Stop using cmd->serial_number in printks.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] fcoe: have fcoe log off and lport destroy before ndo_fcoe_disable

Currently fcoe interface cleanup is done after ndo_fcoe_disable
and that prevents logoff going out to the peer, so this patch
moves all netdev cleanup and its releasing inside
fcoe_interface_cleanup to have log off before ndo_fcoe_disable
disables the fcoe.

This patch also fixes asymmetric rtnl locking around fcoe_if_destroy,
as currently this function requires rtnl held by its caller
and then have this func drops the lock, instead now don't have
any processing under rtnl inside fcoe_if_destroy, this required
moving few func to get build working again.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] libfc: rec tov value and REC_TOV_CONST units usages is incorrect

Added REC_TOV_CONST intent was to have rec tov as e_d_tov + 1s
but currently it is e_d_tov + 1ms since e_d_tov is stored in ms
unit.

Also returned rec tov by get_fsp_rec_tov is in ms and this ms tov
is used as-is with fc_fcp_timer_set expecting jiffies tov.

Fixed this by having get_fsp_rec_tov return rec tov in jiffies
as e_d_tov + 1s and then use jiffies tov w/ fc_fcp_timer_set.

Also some cleanup, no need to cache get_fsp_rec_tov return value
in local rec_tov at various places.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] libfc: remove duplicate ema_list init

As ema_list is already initialized by libfc_host_alloc.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] libfcoe: fix wrong comment in fcoe_transport_detach

fix typo of '_attach' -> '_detach' in the comment.

Reported-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] libfcoe: fix possible buffer overflow in fcoe_transport_show

possible buffer overflow in fcoe_transport_show when reaching the end of
buffer and crossing PAGE_SIZE boundary.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] libfcoe: clean up netdev mapping properly when the transport goes away

When rmmoving the underlying fcoe transport driver module by force when
it's attached and in use, the correspoding netdev mapping should be
cleaned up properly as well, otherwise the lookup for a given netdev
for the transport would still return non NULL pointer, causing "unable
to handle paging request" bug.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] libfc: Move host_lock usage into ramp_up/down routines

The host_lock is still used to protect the can_queue
value in the Scsi_Host, but it doesn't need to be held
and released by each caller. This patch moves the lock
usage into the fc_fcp_can_queue_ramp_up and
fc_fcp_can_queue_ramp_down routines.

Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] esp, scsi_tgt_lib, fcoe: use list_move() instead of list_del()/list_add() combination

Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] fcoe: remove unnecessary module state check

The check of module state being MODULE_STATE_LIVE is no longer needed for the
individual fcoe transport driver, e.g., fcoe.ko, as sysfs entries now go to
libfcoe now, if it reaches fcoe.ko, it has to be already registered. The module
state check for libfcoe will guard the possible race condition of sysfs being
writable before module_init function is called and after module_exit.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] fcoe: Remove mutex_trylock/restart_syscall checks

These checks were initially added to avoid a lockdep
false positive when dealing with the s_active, rtnl
and fcoe_config_mutex mutexes. Recently the create,
destroy, enable and disable sysfs entries were moved
from fcoe.ko to libfcoe.ko. With this change the mutex
usage was shuffled around and the lockdep false
positive stopped happening. We can now remove these
checks.

Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] libfcoe: Remove mutex_trylock/restart_syscall checks

This code was incorrectly ported from fcoe.c when the
fcoe transport infrastructure was put into place. It
was originally needed in fcoe.c when dealing with
the rtnl mutex. In that code it was only needed to
avoid a lockdep false positive. In libfcoe we don't
deal with the rtnl mutex, we don't get the lockdep
false positive and therefore we don't need these
checks.

Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] bnx2fc: introduce missing kfree

Error handling code following a kmalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@

x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...x...+> }
(
x->f1 = E
|
 (x->f1 == NULL || ...)
|
 f(...,x->f1,...)
)
...>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] ipr: fix synchronous request flags for better performance

In testing it was noticed that Extended Delay after Reset flag was being set
for gscsi and volume set devices.  This had a negative effect on performance
for volume sets.  The fix is to only set the flag for gscsi devices.

Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Update version number to 8.03.07.03-k.

A minor change in the versioning. We'll be attaching the "-k"
in the end.

Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Log fcport state transitions when debug messages are enabled.

Add the inline function qla2x00_set_port_state() so that when a fcport state
transition happens we can log the state transition if debug messages are
enabled.

Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Verify login-state has transitioned to PRLI-completed.

Before driver's own internal state is marked as PLOGI/PRLI
complete. This additional check closes a window seen with
dual-personality initiator/target devices where a driver's
PLOGI/PRLI request occurs within the window after the target's
PLOGI request has completed, but prior to the target's PRLI
arriving and processed by the firmware. Without this additional
check, the firmware will return port-information stating that the
port neither supports target nor initiator functions, causing the
driver to register the rport prematurely to the FC-transport
without the proper 'roles' being set.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Limit the logs in case device state does not change for ISP82xx.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add the ql2xdontresethba module_param.

Also, change the ISP82xx code to only reset if this module_param is set
and reset is intended via the QLA82XX_DEV_NEED_RESET case.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Display hardware/firmware registers to get more information about the error for ISP82xx.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Add test for valid loop id to qla2x00_relogin().

If fabric device has invalid loop id (FC_NO_LOOP_ID) then call
qla2x00_find_new_loop_id() to attempt to obtain valid loop id.

Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Perform FCoE context reset before trying adapter reset for ISP82xx.

For certain failures, try to recover first by doing FCoE context reset before
attempting big hammer approach(adpater reset).

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Remove extra call to qla82xx_check_fw_alive().

The stanadlone call to qla82xx_check_fw_alive() in qla82xx_watchdog()
is a typo, so remove it.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Updated the reset sequence for ISP82xx.

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Update copyright banner.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Update License file.

Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Free firmware PCB on logout request.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Include request queue ID in the upper 16-bits of the I/O handle for Abort I/O IOCBs.

The upper 16-bits of the handle for all I/O in multi-queue supported
drivers carries the ID of the request queue it was submitted on. When
using Abort I/O IOCB, the driver needs to also populate the upper
16-bits in the handle_to_abort field so the fw can correlate with the
actual I/O.

Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Remove extraneous setting of FCF_ASYNC_SENT during login-done completion.

The bit is already set upon entry.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Check for a match before attempting to set FCP-priority information.

Modifying qla24xx_get_fcp_prio() to return a 'found' status
allows the driver to short circuit the 'set FCP-priority' call
and reduce the amount of noise generated in the messages file:

scsi(5): Unable to activate fcp priority,  ret=0x102
scsi(5): Unable to activate fcp priority,  ret=0x102

Also make qla24xx_get_fcp_prio() static.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Correct calling contexts of qla2x00_mark_device_lost() in async paths.

The respective done() functions are called from process context,
so there's no reason to 'defer' the request.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] qla2xxx: Display PortID information during FCP command-status handling.

To provide a clearer translation of the command-status origin in
relation to the midlayer's standard SCSI nexus.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>

[SCSI] be2iscsi: Fix for proper setting of FW

There was a bug in setting up type and dmsg for FW

Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>