debugf0("Reading F10_DCTL_SEL_HIGH failed\n");
}
+/*
+ * determine channel based on the interleaving mode: F10h BKDG, 2.8.9 Memory
+ * Interleaving Modes.
+ */
static u32 f10_determine_channel(struct amd64_pvt *pvt, u64 sys_addr,
int hi_range_sel, u32 intlv_en)
{
else if (hi_range_sel)
cs = dct_sel_high;
else if (dct_interleave_enabled(pvt)) {
+ /*
+ * see F2x110[DctSelIntLvAddr] - channel interleave mode
+ */
if (dct_sel_interleave_addr(pvt) == 0)
cs = sys_addr >> 6 & 1;
else if ((dct_sel_interleave_addr(pvt) >> 1) & 1) {
return 0;
}
-static inline u64 f10_determine_base_addr_offset(u64 sys_addr, int hi_range_sel,
+/* See F10h BKDG, 2.8.10.2 DctSelBaseOffset Programming */
+static inline u64 f10_get_base_addr_offset(u64 sys_addr, int hi_range_sel,
u32 dct_sel_base_addr,
u64 dct_sel_base_off,
- u32 hole_en, u32 hole_off,
+ u32 hole_valid, u32 hole_off,
u64 dram_base)
{
u64 chan_off;
if (hi_range_sel) {
if (!(dct_sel_base_addr & 0xFFFFF800) &&
- (hole_en & 1) && (sys_addr >= 0x100000000ULL))
+ hole_valid && (sys_addr >= 0x100000000ULL))
chan_off = hole_off << 16;
else
chan_off = dct_sel_base_off;
} else {
- if ((hole_en & 1) && (sys_addr >= 0x100000000ULL))
+ if (hole_valid && (sys_addr >= 0x100000000ULL))
chan_off = hole_off << 16;
else
chan_off = dram_base & 0xFFFFF8000000ULL;
return cs_found;
}
+/* For a given @dram_range, check if @sys_addr falls within it. */
+static int f10_match_to_this_node(struct amd64_pvt *pvt, int dram_range,
+ u64 sys_addr, int *nid, int *chan_sel)
+{
+ int node_id, cs_found = -EINVAL, high_range = 0;
+ u32 intlv_en, intlv_sel, intlv_shift, hole_off;
+ u32 hole_valid, tmp, dct_sel_base, channel;
+ u64 dram_base, chan_addr, dct_sel_base_off;
+
+ dram_base = pvt->dram_base[dram_range];
+ intlv_en = pvt->dram_IntlvEn[dram_range];
+
+ node_id = pvt->dram_DstNode[dram_range];
+ intlv_sel = pvt->dram_IntlvSel[dram_range];
+
+ debugf1("(dram=%d) Base=0x%llx SystemAddr= 0x%llx Limit=0x%llx\n",
+ dram_range, dram_base, sys_addr, pvt->dram_limit[dram_range]);
+
+ /*
+ * This assumes that one node's DHAR is the same as all the other
+ * nodes' DHAR.
+ */
+ hole_off = (pvt->dhar & 0x0000FF80);
+ hole_valid = (pvt->dhar & 0x1);
+ dct_sel_base_off = (pvt->dram_ctl_select_high & 0xFFFFFC00) << 16;
+
+ debugf1(" HoleOffset=0x%x HoleValid=0x%x IntlvSel=0x%x\n",
+ hole_off, hole_valid, intlv_sel);
+
+ if (intlv_en ||
+ (intlv_sel != ((sys_addr >> 12) & intlv_en)))
+ return -EINVAL;
+
+ dct_sel_base = dct_sel_baseaddr(pvt);
+
+ /*
+ * check whether addresses >= DctSelBaseAddr[47:27] are to be used to
+ * select between DCT0 and DCT1.
+ */
+ if (dct_high_range_enabled(pvt) &&
+ !dct_ganging_enabled(pvt) &&
+ ((sys_addr >> 27) >= (dct_sel_base >> 11)))
+ high_range = 1;
+
+ channel = f10_determine_channel(pvt, sys_addr, high_range, intlv_en);
+
+ chan_addr = f10_get_base_addr_offset(sys_addr, high_range, dct_sel_base,
+ dct_sel_base_off, hole_valid,
+ hole_off, dram_base);
+
+ intlv_shift = f10_map_intlv_en_to_shift(intlv_en);
+
+ /* remove Node ID (in case of memory interleaving) */
+ tmp = chan_addr & 0xFC0;
+
+ chan_addr = ((chan_addr >> intlv_shift) & 0xFFFFFFFFF000ULL) | tmp;
+
+ /* remove channel interleave and hash */
+ if (dct_interleave_enabled(pvt) &&
+ !dct_high_range_enabled(pvt) &&
+ !dct_ganging_enabled(pvt)) {
+ if (dct_sel_interleave_addr(pvt) != 1)
+ chan_addr = (chan_addr >> 1) & 0xFFFFFFFFFFFFFFC0ULL;
+ else {
+ tmp = chan_addr & 0xFC0;
+ chan_addr = ((chan_addr & 0xFFFFFFFFFFFFC000ULL) >> 1)
+ | tmp;
+ }
+ }
+
+ debugf1(" (ChannelAddrLong=0x%llx) >> 8 becomes InputAddr=0x%x\n",
+ chan_addr, (u32)(chan_addr >> 8));
+
+ cs_found = f10_lookup_addr_in_dct(chan_addr >> 8, node_id, channel);
+
+ if (cs_found >= 0) {
+ *nid = node_id;
+ *chan_sel = channel;
+ }
+ return cs_found;
+}
+
+static int f10_translate_sysaddr_to_cs(struct amd64_pvt *pvt, u64 sys_addr,
+ int *node, int *chan_sel)
+{
+ int dram_range, cs_found = -EINVAL;
+ u64 dram_base, dram_limit;
+
+ for (dram_range = 0; dram_range < DRAM_REG_COUNT; dram_range++) {
+
+ if (!pvt->dram_rw_en[dram_range])
+ continue;
+
+ dram_base = pvt->dram_base[dram_range];
+ dram_limit = pvt->dram_limit[dram_range];
+
+ if ((dram_base <= sys_addr) && (sys_addr <= dram_limit)) {
+
+ cs_found = f10_match_to_this_node(pvt, dram_range,
+ sys_addr, node,
+ chan_sel);
+ if (cs_found >= 0)
+ break;
+ }
+ }
+ return cs_found;
+}
+
+/*
+ * This the F10h reference code from AMD to map a @sys_addr to NodeID,
+ * CSROW, Channel.
+ *
+ * The @sys_addr is usually an error address received from the hardware.
+ */
+static void f10_map_sysaddr_to_csrow(struct mem_ctl_info *mci,
+ struct amd64_error_info_regs *info,
+ u64 sys_addr)
+{
+ struct amd64_pvt *pvt = mci->pvt_info;
+ u32 page, offset;
+ unsigned short syndrome;
+ int nid, csrow, chan = 0;
+
+ csrow = f10_translate_sysaddr_to_cs(pvt, sys_addr, &nid, &chan);
+
+ if (csrow >= 0) {
+ error_address_to_page_and_offset(sys_addr, &page, &offset);
+
+ syndrome = EXTRACT_HIGH_SYNDROME(info->nbsl) << 8;
+ syndrome |= EXTRACT_LOW_SYNDROME(info->nbsh);
+
+ /*
+ * Is CHIPKILL on? If so, then we can attempt to use the
+ * syndrome to isolate which channel the error was on.
+ */
+ if (pvt->nbcfg & K8_NBCFG_CHIPKILL)
+ chan = get_channel_from_ecc_syndrome(syndrome);
+
+ if (chan >= 0) {
+ edac_mc_handle_ce(mci, page, offset, syndrome,
+ csrow, chan, EDAC_MOD_STR);
+ } else {
+ /*
+ * Channel unknown, report all channels on this
+ * CSROW as failed.
+ */
+ for (chan = 0; chan < mci->csrows[csrow].nr_channels;
+ chan++) {
+ edac_mc_handle_ce(mci, page, offset,
+ syndrome,
+ csrow, chan,
+ EDAC_MOD_STR);
+ }
+ }
+
+ } else {
+ edac_mc_handle_ce_no_info(mci, EDAC_MOD_STR);
+ }
+}
+
+/*
+ * Input (@index) is the DBAM DIMM value (1 of 4) used as an index into a shift
+ * table (revf_quad_ddr2_shift) which starts at 128MB DIMM size. Index of 0
+ * indicates an empty DIMM slot, as reported by Hardware on empty slots.
+ *
+ * Normalize to 128MB by subracting 27 bit shift.
+ */
+static int map_dbam_to_csrow_size(int index)
+{
+ int mega_bytes = 0;
+
+ if (index > 0 && index <= DBAM_MAX_VALUE)
+ mega_bytes = ((128 << (revf_quad_ddr2_shift[index]-27)));
+
+ return mega_bytes;
+}
+
+/*
+ * debug routine to display the memory sizes of a DIMM (ganged or not) and it
+ * CSROWs as well
+ */
+static void f10_debug_display_dimm_sizes(int ctrl, struct amd64_pvt *pvt,
+ int ganged)
+{
+ int dimm, size0, size1;
+ u32 dbam;
+ u32 *dcsb;
+
+ debugf1(" dbam%d: 0x%8.08x CSROW is %s\n", ctrl,
+ ctrl ? pvt->dbam1 : pvt->dbam0,
+ ganged ? "GANGED - dbam1 not used" : "NON-GANGED");
+
+ dbam = ctrl ? pvt->dbam1 : pvt->dbam0;
+ dcsb = ctrl ? pvt->dcsb1 : pvt->dcsb0;
+
+ /* Dump memory sizes for DIMM and its CSROWs */
+ for (dimm = 0; dimm < 4; dimm++) {
+
+ size0 = 0;
+ if (dcsb[dimm*2] & K8_DCSB_CS_ENABLE)
+ size0 = map_dbam_to_csrow_size(DBAM_DIMM(dimm, dbam));
+
+ size1 = 0;
+ if (dcsb[dimm*2 + 1] & K8_DCSB_CS_ENABLE)
+ size1 = map_dbam_to_csrow_size(DBAM_DIMM(dimm, dbam));
+
+ debugf1(" CTRL-%d DIMM-%d=%5dMB CSROW-%d=%5dMB "
+ "CSROW-%d=%5dMB\n",
+ ctrl,
+ dimm,
+ size0 + size1,
+ dimm * 2,
+ size0,
+ dimm * 2 + 1,
+ size1);
+ }
+}
+
+/*
+ * Very early hardware probe on pci_probe thread to determine if this module
+ * supports the hardware.
+ *
+ * Return:
+ * 0 for OK
+ * 1 for error
+ */
+static int f10_probe_valid_hardware(struct amd64_pvt *pvt)
+{
+ int ret = 0;
+
+ /*
+ * If we are on a DDR3 machine, we don't know yet if
+ * we support that properly at this time
+ */
+ if ((pvt->dchr0 & F10_DCHR_Ddr3Mode) ||
+ (pvt->dchr1 & F10_DCHR_Ddr3Mode)) {
+
+ amd64_printk(KERN_WARNING,
+ "%s() This machine is running with DDR3 memory. "
+ "This is not currently supported. "
+ "DCHR0=0x%x DCHR1=0x%x\n",
+ __func__, pvt->dchr0, pvt->dchr1);
+
+ amd64_printk(KERN_WARNING,
+ " Contact '%s' module MAINTAINER to help add"
+ " support.\n",
+ EDAC_MOD_STR);
+
+ ret = 1;
+
+ }
+ return ret;
+}
git.openpandora.org / pandora-kernel.git / commitdiff