--- /dev/null
+/*****************************************************************************
+* Copyright 2004 - 2008 Broadcom Corporation. All rights reserved.
+*
+* Unless you and Broadcom execute a separate written software license
+* agreement governing use of this software, this software is licensed to you
+* under the terms of the GNU General Public License version 2, available at
+* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
+*
+* Notwithstanding the above, under no circumstances may you combine this
+* software in any way with any other Broadcom software provided under a
+* license other than the GPL, without Broadcom's express prior written
+* consent.
+*****************************************************************************/
+
+/****************************************************************************/
+/**
+* @file chipcHw_reg.h
+*
+* @brief Definitions for low level chip control registers
+*
+*/
+/****************************************************************************/
+#ifndef CHIPCHW_REG_H
+#define CHIPCHW_REG_H
+
+#include <mach/csp/mm_io.h>
+#include <csp/reg.h>
+#include <mach/csp/ddrcReg.h>
+
+#define chipcHw_BASE_ADDRESS MM_IO_BASE_CHIPC
+
+typedef struct {
+ uint32_t ChipId; /* Chip ID */
+ uint32_t DDRClock; /* PLL1 Channel 1 for DDR clock */
+ uint32_t ARMClock; /* PLL1 Channel 2 for ARM clock */
+ uint32_t ESWClock; /* PLL1 Channel 3 for ESW system clock */
+ uint32_t VPMClock; /* PLL1 Channel 4 for VPM clock */
+ uint32_t ESW125Clock; /* PLL1 Channel 5 for ESW 125MHz clock */
+ uint32_t UARTClock; /* PLL1 Channel 6 for UART clock */
+ uint32_t SDIO0Clock; /* PLL1 Channel 7 for SDIO 0 clock */
+ uint32_t SDIO1Clock; /* PLL1 Channel 8 for SDIO 1 clock */
+ uint32_t SPIClock; /* PLL1 Channel 9 for SPI master Clock */
+ uint32_t ETMClock; /* PLL1 Channel 10 for ARM ETM Clock */
+
+ uint32_t ACLKClock; /* ACLK Clock (Divider) */
+ uint32_t OTPClock; /* OTP Clock (Divider) */
+ uint32_t I2CClock; /* I2C Clock (CK_13m) (Divider) */
+ uint32_t I2S0Clock; /* I2S0 Clock (Divider) */
+ uint32_t RTBUSClock; /* RTBUS (DDR PHY Config.) Clock (Divider) */
+ uint32_t pad1;
+ uint32_t APM100Clock; /* APM 100MHz CLK Clock (Divider) */
+ uint32_t TSCClock; /* TSC Clock (Divider) */
+ uint32_t LEDClock; /* LED Clock (Divider) */
+
+ uint32_t USBClock; /* PLL2 Channel 1 for USB clock */
+ uint32_t LCDClock; /* PLL2 Channel 2 for LCD clock */
+ uint32_t APMClock; /* PLL2 Channel 3 for APM 200 MHz clock */
+
+ uint32_t BusIntfClock; /* Bus interface clock */
+
+ uint32_t PLLStatus; /* PLL status register (PLL1) */
+ uint32_t PLLConfig; /* PLL configuration register (PLL1) */
+ uint32_t PLLPreDivider; /* PLL pre-divider control register (PLL1) */
+ uint32_t PLLDivider; /* PLL divider control register (PLL1) */
+ uint32_t PLLControl1; /* PLL analog control register #1 (PLL1) */
+ uint32_t PLLControl2; /* PLL analog control register #2 (PLL1) */
+
+ uint32_t I2S1Clock; /* I2S1 Clock */
+ uint32_t AudioEnable; /* Enable/ disable audio channel */
+ uint32_t SoftReset1; /* Reset blocks */
+ uint32_t SoftReset2; /* Reset blocks */
+ uint32_t Spare1; /* Phase align interrupts */
+ uint32_t Sticky; /* Sticky bits */
+ uint32_t MiscCtrl; /* Misc. control */
+ uint32_t pad3[3];
+
+ uint32_t PLLStatus2; /* PLL status register (PLL2) */
+ uint32_t PLLConfig2; /* PLL configuration register (PLL2) */
+ uint32_t PLLPreDivider2; /* PLL pre-divider control register (PLL2) */
+ uint32_t PLLDivider2; /* PLL divider control register (PLL2) */
+ uint32_t PLLControl12; /* PLL analog control register #1 (PLL2) */
+ uint32_t PLLControl22; /* PLL analog control register #2 (PLL2) */
+
+ uint32_t DDRPhaseCtrl1; /* DDR Clock Phase Alignment control1 */
+ uint32_t VPMPhaseCtrl1; /* VPM Clock Phase Alignment control1 */
+ uint32_t PhaseAlignStatus; /* DDR/VPM Clock Phase Alignment Status */
+ uint32_t PhaseCtrlStatus; /* DDR/VPM Clock HW DDR/VPM ph_ctrl and load_ch Status */
+ uint32_t DDRPhaseCtrl2; /* DDR Clock Phase Alignment control2 */
+ uint32_t VPMPhaseCtrl2; /* VPM Clock Phase Alignment control2 */
+ uint32_t pad4[9];
+
+ uint32_t SoftOTP1; /* Software OTP control */
+ uint32_t SoftOTP2; /* Software OTP control */
+ uint32_t SoftStraps; /* Software strap */
+ uint32_t PinStraps; /* Pin Straps */
+ uint32_t DiffOscCtrl; /* Diff oscillator control */
+ uint32_t DiagsCtrl; /* Diagnostic control */
+ uint32_t DiagsOutputCtrl; /* Diagnostic output enable */
+ uint32_t DiagsReadBackCtrl; /* Diagnostic read back control */
+
+ uint32_t LcdPifMode; /* LCD/PIF Pin Sharing MUX Mode */
+
+ uint32_t GpioMux_0_7; /* Pin Sharing MUX0 Control */
+ uint32_t GpioMux_8_15; /* Pin Sharing MUX1 Control */
+ uint32_t GpioMux_16_23; /* Pin Sharing MUX2 Control */
+ uint32_t GpioMux_24_31; /* Pin Sharing MUX3 Control */
+ uint32_t GpioMux_32_39; /* Pin Sharing MUX4 Control */
+ uint32_t GpioMux_40_47; /* Pin Sharing MUX5 Control */
+ uint32_t GpioMux_48_55; /* Pin Sharing MUX6 Control */
+ uint32_t GpioMux_56_63; /* Pin Sharing MUX7 Control */
+
+ uint32_t GpioSR_0_7; /* Slew rate for GPIO 0 - 7 */
+ uint32_t GpioSR_8_15; /* Slew rate for GPIO 8 - 15 */
+ uint32_t GpioSR_16_23; /* Slew rate for GPIO 16 - 23 */
+ uint32_t GpioSR_24_31; /* Slew rate for GPIO 24 - 31 */
+ uint32_t GpioSR_32_39; /* Slew rate for GPIO 32 - 39 */
+ uint32_t GpioSR_40_47; /* Slew rate for GPIO 40 - 47 */
+ uint32_t GpioSR_48_55; /* Slew rate for GPIO 48 - 55 */
+ uint32_t GpioSR_56_63; /* Slew rate for GPIO 56 - 63 */
+ uint32_t MiscSR_0_7; /* Slew rate for MISC 0 - 7 */
+ uint32_t MiscSR_8_15; /* Slew rate for MISC 8 - 15 */
+
+ uint32_t GpioPull_0_15; /* Pull up registers for GPIO 0 - 15 */
+ uint32_t GpioPull_16_31; /* Pull up registers for GPIO 16 - 31 */
+ uint32_t GpioPull_32_47; /* Pull up registers for GPIO 32 - 47 */
+ uint32_t GpioPull_48_63; /* Pull up registers for GPIO 48 - 63 */
+ uint32_t MiscPull_0_15; /* Pull up registers for MISC 0 - 15 */
+
+ uint32_t GpioInput_0_31; /* Input type for GPIO 0 - 31 */
+ uint32_t GpioInput_32_63; /* Input type for GPIO 32 - 63 */
+ uint32_t MiscInput_0_15; /* Input type for MISC 0 - 16 */
+} chipcHw_REG_t;
+
+#define pChipcHw ((volatile chipcHw_REG_t *) chipcHw_BASE_ADDRESS)
+#define pChipcPhysical ((volatile chipcHw_REG_t *) MM_ADDR_IO_CHIPC)
+
+#define chipcHw_REG_CHIPID_BASE_MASK 0xFFFFF000
+#define chipcHw_REG_CHIPID_BASE_SHIFT 12
+#define chipcHw_REG_CHIPID_REV_MASK 0x00000FFF
+#define chipcHw_REG_REV_A0 0xA00
+#define chipcHw_REG_REV_B0 0x0B0
+
+#define chipcHw_REG_PLL_STATUS_CONTROL_ENABLE 0x80000000 /* Allow controlling PLL registers */
+#define chipcHw_REG_PLL_STATUS_LOCKED 0x00000001 /* PLL is settled */
+#define chipcHw_REG_PLL_CONFIG_D_RESET 0x00000008 /* Digital reset */
+#define chipcHw_REG_PLL_CONFIG_A_RESET 0x00000004 /* Analog reset */
+#define chipcHw_REG_PLL_CONFIG_BYPASS_ENABLE 0x00000020 /* Bypass enable */
+#define chipcHw_REG_PLL_CONFIG_OUTPUT_ENABLE 0x00000010 /* Output enable */
+#define chipcHw_REG_PLL_CONFIG_POWER_DOWN 0x00000001 /* Power down */
+#define chipcHw_REG_PLL_CONFIG_VCO_SPLIT_FREQ 1600000000 /* 1.6GHz VCO split frequency */
+#define chipcHw_REG_PLL_CONFIG_VCO_800_1600 0x00000000 /* VCO range 800-1600 MHz */
+#define chipcHw_REG_PLL_CONFIG_VCO_1601_3200 0x00000080 /* VCO range 1601-3200 MHz */
+#define chipcHw_REG_PLL_CONFIG_TEST_ENABLE 0x00010000 /* PLL test output enable */
+#define chipcHw_REG_PLL_CONFIG_TEST_SELECT_MASK 0x003E0000 /* Mask to set test values */
+#define chipcHw_REG_PLL_CONFIG_TEST_SELECT_SHIFT 17
+
+#define chipcHw_REG_PLL_CLOCK_PHASE_COMP 0x00800000 /* Phase comparator output */
+#define chipcHw_REG_PLL_CLOCK_TO_BUS_RATIO_MASK 0x00300000 /* Clock to bus ratio mask */
+#define chipcHw_REG_PLL_CLOCK_TO_BUS_RATIO_SHIFT 20 /* Number of bits to be shifted */
+#define chipcHw_REG_PLL_CLOCK_POWER_DOWN 0x00080000 /* PLL channel power down */
+#define chipcHw_REG_PLL_CLOCK_SOURCE_GPIO 0x00040000 /* Use GPIO as source */
+#define chipcHw_REG_PLL_CLOCK_BYPASS_SELECT 0x00020000 /* Select bypass clock */
+#define chipcHw_REG_PLL_CLOCK_OUTPUT_ENABLE 0x00010000 /* Clock gated ON */
+#define chipcHw_REG_PLL_CLOCK_PHASE_UPDATE_ENABLE 0x00008000 /* Clock phase update enable */
+#define chipcHw_REG_PLL_CLOCK_PHASE_CONTROL_SHIFT 8 /* Number of bits to be shifted */
+#define chipcHw_REG_PLL_CLOCK_PHASE_CONTROL_MASK 0x00003F00 /* Phase control mask */
+#define chipcHw_REG_PLL_CLOCK_MDIV_MASK 0x000000FF /* Clock post divider mask
+
+ 00000000 = divide-by-256
+ 00000001 = divide-by-1
+ 00000010 = divide-by-2
+ 00000011 = divide-by-3
+ 00000100 = divide-by-4
+ 00000101 = divide-by-5
+ 00000110 = divide-by-6
+ .
+ .
+ 11111011 = divide-by-251
+ 11111100 = divide-by-252
+ 11111101 = divide-by-253
+ 11111110 = divide-by-254
+ */
+
+#define chipcHw_REG_DIV_CLOCK_SOURCE_OTHER 0x00040000 /* NON-PLL clock source select */
+#define chipcHw_REG_DIV_CLOCK_BYPASS_SELECT 0x00020000 /* NON-PLL clock bypass enable */
+#define chipcHw_REG_DIV_CLOCK_OUTPUT_ENABLE 0x00010000 /* NON-PLL clock output enable */
+#define chipcHw_REG_DIV_CLOCK_DIV_MASK 0x000000FF /* NON-PLL clock post-divide mask */
+#define chipcHw_REG_DIV_CLOCK_DIV_256 0x00000000 /* NON-PLL clock post-divide by 256 */
+
+#define chipcHw_REG_PLL_PREDIVIDER_P1_SHIFT 0
+#define chipcHw_REG_PLL_PREDIVIDER_P2_SHIFT 4
+#define chipcHw_REG_PLL_PREDIVIDER_NDIV_SHIFT 8
+#define chipcHw_REG_PLL_PREDIVIDER_NDIV_MASK 0x0001FF00
+#define chipcHw_REG_PLL_PREDIVIDER_POWER_DOWN 0x02000000
+#define chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_MASK 0x00700000 /* Divider mask */
+#define chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_INTEGER 0x00000000 /* Integer-N Mode */
+#define chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_MASH_UNIT 0x00100000 /* MASH Sigma-Delta Modulator Unit Mode */
+#define chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_MFB_UNIT 0x00200000 /* MFB Sigma-Delta Modulator Unit Mode */
+#define chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_MASH_1_8 0x00300000 /* MASH Sigma-Delta Modulator 1/8 Mode */
+#define chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_MFB_1_8 0x00400000 /* MFB Sigma-Delta Modulator 1/8 Mode */
+
+#define chipcHw_REG_PLL_PREDIVIDER_NDIV_i(vco) ((vco) / chipcHw_XTAL_FREQ_Hz)
+#define chipcHw_REG_PLL_PREDIVIDER_P1 1
+#define chipcHw_REG_PLL_PREDIVIDER_P2 1
+
+#define chipcHw_REG_PLL_DIVIDER_M1DIV 0x03000000
+#define chipcHw_REG_PLL_DIVIDER_FRAC 0x00FFFFFF /* Fractional divider */
+
+#define chipcHw_REG_PLL_DIVIDER_NDIV_f_SS (0x00FFFFFF) /* To attain spread with max frequency */
+
+#define chipcHw_REG_PLL_DIVIDER_NDIV_f 0 /* ndiv_frac = chipcHw_REG_PLL_DIVIDER_NDIV_f /
+ chipcHw_REG_PLL_DIVIDER_FRAC
+ = 0, when SS is disable
+ */
+
+#define chipcHw_REG_PLL_DIVIDER_MDIV(vco, Hz) ((chipcHw_divide((vco), (Hz)) > 255) ? 0 : chipcHw_divide((vco), (Hz)))
+
+#define chipcHw_REG_ACLKClock_CLK_DIV_MASK 0x3
+
+/* System booting strap options */
+#define chipcHw_STRAPS_SOFT_OVERRIDE 0x00000001 /* Software Strap Override */
+
+#define chipcHw_STRAPS_BOOT_DEVICE_NAND_FLASH_8 0x00000000 /* 8 bit NAND FLASH Boot */
+#define chipcHw_STRAPS_BOOT_DEVICE_NOR_FLASH_16 0x00000002 /* 16 bit NOR FLASH Boot */
+#define chipcHw_STRAPS_BOOT_DEVICE_SERIAL_FLASH 0x00000004 /* Serial FLASH Boot */
+#define chipcHw_STRAPS_BOOT_DEVICE_NAND_FLASH_16 0x00000006 /* 16 bit NAND FLASH Boot */
+#define chipcHw_STRAPS_BOOT_DEVICE_UART 0x00000008 /* UART Boot */
+#define chipcHw_STRAPS_BOOT_DEVICE_MASK 0x0000000E /* Mask */
+
+/* System boot option */
+#define chipcHw_STRAPS_BOOT_OPTION_BROM 0x00000000 /* Boot from Boot ROM */
+#define chipcHw_STRAPS_BOOT_OPTION_ARAM 0x00000020 /* Boot from ARAM */
+#define chipcHw_STRAPS_BOOT_OPTION_NOR 0x00000030 /* Boot from NOR flash */
+
+/* NAND Flash page size strap options */
+#define chipcHw_STRAPS_NAND_PAGESIZE_512 0x00000000 /* NAND FLASH page size of 512 bytes */
+#define chipcHw_STRAPS_NAND_PAGESIZE_2048 0x00000040 /* NAND FLASH page size of 2048 bytes */
+#define chipcHw_STRAPS_NAND_PAGESIZE_4096 0x00000080 /* NAND FLASH page size of 4096 bytes */
+#define chipcHw_STRAPS_NAND_PAGESIZE_EXT 0x000000C0 /* NAND FLASH page of extened size */
+#define chipcHw_STRAPS_NAND_PAGESIZE_MASK 0x000000C0 /* Mask */
+
+#define chipcHw_STRAPS_NAND_EXTRA_CYCLE 0x00000400 /* NAND FLASH address cycle configuration */
+#define chipcHw_STRAPS_REBOOT_TO_UART 0x00000800 /* Reboot to UART on error */
+
+/* Secure boot mode strap options */
+#define chipcHw_STRAPS_BOOT_MODE_NORMAL 0x00000000 /* Normal Boot */
+#define chipcHw_STRAPS_BOOT_MODE_DBG_SW 0x00000100 /* Software debugging Boot */
+#define chipcHw_STRAPS_BOOT_MODE_DBG_BOOT 0x00000200 /* Boot rom debugging Boot */
+#define chipcHw_STRAPS_BOOT_MODE_NORMAL_QUIET 0x00000300 /* Normal Boot (Quiet BootRom) */
+#define chipcHw_STRAPS_BOOT_MODE_MASK 0x00000300 /* Mask */
+
+/* Slave Mode straps */
+#define chipcHw_STRAPS_I2CS 0x02000000 /* I2C Slave */
+#define chipcHw_STRAPS_SPIS 0x01000000 /* SPI Slave */
+
+/* Strap pin options */
+#define chipcHw_REG_SW_STRAPS ((pChipcHw->PinStraps & 0x0000FC00) >> 10)
+
+/* PIF/LCD pin sharing defines */
+#define chipcHw_REG_LCD_PIN_ENABLE 0x00000001 /* LCD Controller is used and the pins have LCD functions */
+#define chipcHw_REG_PIF_PIN_ENABLE 0x00000002 /* LCD pins are used to perform PIF functions */
+
+#define chipcHw_GPIO_COUNT 61 /* Number of GPIO pin accessible thorugh CHIPC */
+
+/* NOTE: Any changes to these constants will require a corresponding change to chipcHw_str.c */
+#define chipcHw_REG_GPIO_MUX_KEYPAD 0x00000001 /* GPIO mux for Keypad */
+#define chipcHw_REG_GPIO_MUX_I2CH 0x00000002 /* GPIO mux for I2CH */
+#define chipcHw_REG_GPIO_MUX_SPI 0x00000003 /* GPIO mux for SPI */
+#define chipcHw_REG_GPIO_MUX_UART 0x00000004 /* GPIO mux for UART */
+#define chipcHw_REG_GPIO_MUX_LEDMTXP 0x00000005 /* GPIO mux for LEDMTXP */
+#define chipcHw_REG_GPIO_MUX_LEDMTXS 0x00000006 /* GPIO mux for LEDMTXS */
+#define chipcHw_REG_GPIO_MUX_SDIO0 0x00000007 /* GPIO mux for SDIO0 */
+#define chipcHw_REG_GPIO_MUX_SDIO1 0x00000008 /* GPIO mux for SDIO1 */
+#define chipcHw_REG_GPIO_MUX_PCM 0x00000009 /* GPIO mux for PCM */
+#define chipcHw_REG_GPIO_MUX_I2S 0x0000000A /* GPIO mux for I2S */
+#define chipcHw_REG_GPIO_MUX_ETM 0x0000000B /* GPIO mux for ETM */
+#define chipcHw_REG_GPIO_MUX_DEBUG 0x0000000C /* GPIO mux for DEBUG */
+#define chipcHw_REG_GPIO_MUX_MISC 0x0000000D /* GPIO mux for MISC */
+#define chipcHw_REG_GPIO_MUX_GPIO 0x00000000 /* GPIO mux for GPIO */
+#define chipcHw_REG_GPIO_MUX(pin) (&pChipcHw->GpioMux_0_7 + ((pin) >> 3))
+#define chipcHw_REG_GPIO_MUX_POSITION(pin) (((pin) & 0x00000007) << 2)
+#define chipcHw_REG_GPIO_MUX_MASK 0x0000000F /* Mask */
+
+#define chipcHw_REG_SLEW_RATE_HIGH 0x00000000 /* High speed slew rate */
+#define chipcHw_REG_SLEW_RATE_NORMAL 0x00000008 /* Normal slew rate */
+ /* Pins beyond 42 are defined by skipping 8 bits within the register */
+#define chipcHw_REG_SLEW_RATE(pin) (((pin) > 42) ? (&pChipcHw->GpioSR_0_7 + (((pin) + 2) >> 3)) : (&pChipcHw->GpioSR_0_7 + ((pin) >> 3)))
+#define chipcHw_REG_SLEW_RATE_POSITION(pin) (((pin) > 42) ? ((((pin) + 2) & 0x00000007) << 2) : (((pin) & 0x00000007) << 2))
+#define chipcHw_REG_SLEW_RATE_MASK 0x00000008 /* Mask */
+
+#define chipcHw_REG_CURRENT_STRENGTH_2mA 0x00000001 /* Current driving strength 2 milli ampere */
+#define chipcHw_REG_CURRENT_STRENGTH_4mA 0x00000002 /* Current driving strength 4 milli ampere */
+#define chipcHw_REG_CURRENT_STRENGTH_6mA 0x00000004 /* Current driving strength 6 milli ampere */
+#define chipcHw_REG_CURRENT_STRENGTH_8mA 0x00000005 /* Current driving strength 8 milli ampere */
+#define chipcHw_REG_CURRENT_STRENGTH_10mA 0x00000006 /* Current driving strength 10 milli ampere */
+#define chipcHw_REG_CURRENT_STRENGTH_12mA 0x00000007 /* Current driving strength 12 milli ampere */
+#define chipcHw_REG_CURRENT_MASK 0x00000007 /* Mask */
+ /* Pins beyond 42 are defined by skipping 8 bits */
+#define chipcHw_REG_CURRENT(pin) (((pin) > 42) ? (&pChipcHw->GpioSR_0_7 + (((pin) + 2) >> 3)) : (&pChipcHw->GpioSR_0_7 + ((pin) >> 3)))
+#define chipcHw_REG_CURRENT_POSITION(pin) (((pin) > 42) ? ((((pin) + 2) & 0x00000007) << 2) : (((pin) & 0x00000007) << 2))
+
+#define chipcHw_REG_PULL_NONE 0x00000000 /* No pull up register */
+#define chipcHw_REG_PULL_UP 0x00000001 /* Pull up register enable */
+#define chipcHw_REG_PULL_DOWN 0x00000002 /* Pull down register enable */
+#define chipcHw_REG_PULLUP_MASK 0x00000003 /* Mask */
+ /* Pins beyond 42 are defined by skipping 4 bits */
+#define chipcHw_REG_PULLUP(pin) (((pin) > 42) ? (&pChipcHw->GpioPull_0_15 + (((pin) + 2) >> 4)) : (&pChipcHw->GpioPull_0_15 + ((pin) >> 4)))
+#define chipcHw_REG_PULLUP_POSITION(pin) (((pin) > 42) ? ((((pin) + 2) & 0x0000000F) << 1) : (((pin) & 0x0000000F) << 1))
+
+#define chipcHw_REG_INPUTTYPE_CMOS 0x00000000 /* Normal CMOS logic */
+#define chipcHw_REG_INPUTTYPE_ST 0x00000001 /* High speed Schmitt Trigger */
+#define chipcHw_REG_INPUTTYPE_MASK 0x00000001 /* Mask */
+ /* Pins beyond 42 are defined by skipping 2 bits */
+#define chipcHw_REG_INPUTTYPE(pin) (((pin) > 42) ? (&pChipcHw->GpioInput_0_31 + (((pin) + 2) >> 5)) : (&pChipcHw->GpioInput_0_31 + ((pin) >> 5)))
+#define chipcHw_REG_INPUTTYPE_POSITION(pin) (((pin) > 42) ? ((((pin) + 2) & 0x0000001F)) : (((pin) & 0x0000001F)))
+
+/* Device connected to the bus clock */
+#define chipcHw_REG_BUS_CLOCK_ARM 0x00000001 /* Bus interface clock for ARM */
+#define chipcHw_REG_BUS_CLOCK_VDEC 0x00000002 /* Bus interface clock for VDEC */
+#define chipcHw_REG_BUS_CLOCK_ARAM 0x00000004 /* Bus interface clock for ARAM */
+#define chipcHw_REG_BUS_CLOCK_HPM 0x00000008 /* Bus interface clock for HPM */
+#define chipcHw_REG_BUS_CLOCK_DDRC 0x00000010 /* Bus interface clock for DDRC */
+#define chipcHw_REG_BUS_CLOCK_DMAC0 0x00000020 /* Bus interface clock for DMAC0 */
+#define chipcHw_REG_BUS_CLOCK_DMAC1 0x00000040 /* Bus interface clock for DMAC1 */
+#define chipcHw_REG_BUS_CLOCK_NVI 0x00000080 /* Bus interface clock for NVI */
+#define chipcHw_REG_BUS_CLOCK_ESW 0x00000100 /* Bus interface clock for ESW */
+#define chipcHw_REG_BUS_CLOCK_GE 0x00000200 /* Bus interface clock for GE */
+#define chipcHw_REG_BUS_CLOCK_I2CH 0x00000400 /* Bus interface clock for I2CH */
+#define chipcHw_REG_BUS_CLOCK_I2S0 0x00000800 /* Bus interface clock for I2S0 */
+#define chipcHw_REG_BUS_CLOCK_I2S1 0x00001000 /* Bus interface clock for I2S1 */
+#define chipcHw_REG_BUS_CLOCK_VRAM 0x00002000 /* Bus interface clock for VRAM */
+#define chipcHw_REG_BUS_CLOCK_CLCD 0x00004000 /* Bus interface clock for CLCD */
+#define chipcHw_REG_BUS_CLOCK_LDK 0x00008000 /* Bus interface clock for LDK */
+#define chipcHw_REG_BUS_CLOCK_LED 0x00010000 /* Bus interface clock for LED */
+#define chipcHw_REG_BUS_CLOCK_OTP 0x00020000 /* Bus interface clock for OTP */
+#define chipcHw_REG_BUS_CLOCK_PIF 0x00040000 /* Bus interface clock for PIF */
+#define chipcHw_REG_BUS_CLOCK_SPU 0x00080000 /* Bus interface clock for SPU */
+#define chipcHw_REG_BUS_CLOCK_SDIO0 0x00100000 /* Bus interface clock for SDIO0 */
+#define chipcHw_REG_BUS_CLOCK_SDIO1 0x00200000 /* Bus interface clock for SDIO1 */
+#define chipcHw_REG_BUS_CLOCK_SPIH 0x00400000 /* Bus interface clock for SPIH */
+#define chipcHw_REG_BUS_CLOCK_SPIS 0x00800000 /* Bus interface clock for SPIS */
+#define chipcHw_REG_BUS_CLOCK_UART0 0x01000000 /* Bus interface clock for UART0 */
+#define chipcHw_REG_BUS_CLOCK_UART1 0x02000000 /* Bus interface clock for UART1 */
+#define chipcHw_REG_BUS_CLOCK_BBL 0x04000000 /* Bus interface clock for BBL */
+#define chipcHw_REG_BUS_CLOCK_I2CS 0x08000000 /* Bus interface clock for I2CS */
+#define chipcHw_REG_BUS_CLOCK_USBH 0x10000000 /* Bus interface clock for USB Host */
+#define chipcHw_REG_BUS_CLOCK_USBD 0x20000000 /* Bus interface clock for USB Device */
+#define chipcHw_REG_BUS_CLOCK_BROM 0x40000000 /* Bus interface clock for Boot ROM */
+#define chipcHw_REG_BUS_CLOCK_TSC 0x80000000 /* Bus interface clock for Touch screen */
+
+/* Software resets defines */
+#define chipcHw_REG_SOFT_RESET_VPM_GLOBAL_HOLD 0x0000000080000000ULL /* Reset Global VPM and hold */
+#define chipcHw_REG_SOFT_RESET_VPM_HOLD 0x0000000040000000ULL /* Reset VPM and hold */
+#define chipcHw_REG_SOFT_RESET_VPM_GLOBAL 0x0000000020000000ULL /* Reset Global VPM */
+#define chipcHw_REG_SOFT_RESET_VPM 0x0000000010000000ULL /* Reset VPM */
+#define chipcHw_REG_SOFT_RESET_KEYPAD 0x0000000008000000ULL /* Reset Key pad */
+#define chipcHw_REG_SOFT_RESET_LED 0x0000000004000000ULL /* Reset LED */
+#define chipcHw_REG_SOFT_RESET_SPU 0x0000000002000000ULL /* Reset SPU */
+#define chipcHw_REG_SOFT_RESET_RNG 0x0000000001000000ULL /* Reset RNG */
+#define chipcHw_REG_SOFT_RESET_PKA 0x0000000000800000ULL /* Reset PKA */
+#define chipcHw_REG_SOFT_RESET_LCD 0x0000000000400000ULL /* Reset LCD */
+#define chipcHw_REG_SOFT_RESET_PIF 0x0000000000200000ULL /* Reset PIF */
+#define chipcHw_REG_SOFT_RESET_I2CS 0x0000000000100000ULL /* Reset I2C Slave */
+#define chipcHw_REG_SOFT_RESET_I2CH 0x0000000000080000ULL /* Reset I2C Host */
+#define chipcHw_REG_SOFT_RESET_SDIO1 0x0000000000040000ULL /* Reset SDIO 1 */
+#define chipcHw_REG_SOFT_RESET_SDIO0 0x0000000000020000ULL /* Reset SDIO 0 */
+#define chipcHw_REG_SOFT_RESET_BBL 0x0000000000010000ULL /* Reset BBL */
+#define chipcHw_REG_SOFT_RESET_I2S1 0x0000000000008000ULL /* Reset I2S1 */
+#define chipcHw_REG_SOFT_RESET_I2S0 0x0000000000004000ULL /* Reset I2S0 */
+#define chipcHw_REG_SOFT_RESET_SPIS 0x0000000000002000ULL /* Reset SPI Slave */
+#define chipcHw_REG_SOFT_RESET_SPIH 0x0000000000001000ULL /* Reset SPI Host */
+#define chipcHw_REG_SOFT_RESET_GPIO1 0x0000000000000800ULL /* Reset GPIO block 1 */
+#define chipcHw_REG_SOFT_RESET_GPIO0 0x0000000000000400ULL /* Reset GPIO block 0 */
+#define chipcHw_REG_SOFT_RESET_UART1 0x0000000000000200ULL /* Reset UART 1 */
+#define chipcHw_REG_SOFT_RESET_UART0 0x0000000000000100ULL /* Reset UART 0 */
+#define chipcHw_REG_SOFT_RESET_NVI 0x0000000000000080ULL /* Reset NVI */
+#define chipcHw_REG_SOFT_RESET_WDOG 0x0000000000000040ULL /* Reset Watch dog */
+#define chipcHw_REG_SOFT_RESET_TMR 0x0000000000000020ULL /* Reset Timer */
+#define chipcHw_REG_SOFT_RESET_ETM 0x0000000000000010ULL /* Reset ETM */
+#define chipcHw_REG_SOFT_RESET_ARM_HOLD 0x0000000000000008ULL /* Reset ARM and HOLD */
+#define chipcHw_REG_SOFT_RESET_ARM 0x0000000000000004ULL /* Reset ARM */
+#define chipcHw_REG_SOFT_RESET_CHIP_WARM 0x0000000000000002ULL /* Chip warm reset */
+#define chipcHw_REG_SOFT_RESET_CHIP_SOFT 0x0000000000000001ULL /* Chip soft reset */
+#define chipcHw_REG_SOFT_RESET_VDEC 0x0000100000000000ULL /* Video decoder */
+#define chipcHw_REG_SOFT_RESET_GE 0x0000080000000000ULL /* Graphics engine */
+#define chipcHw_REG_SOFT_RESET_OTP 0x0000040000000000ULL /* Reset OTP */
+#define chipcHw_REG_SOFT_RESET_USB2 0x0000020000000000ULL /* Reset USB2 */
+#define chipcHw_REG_SOFT_RESET_USB1 0x0000010000000000ULL /* Reset USB 1 */
+#define chipcHw_REG_SOFT_RESET_USB 0x0000008000000000ULL /* Reset USB 1 and USB2 soft reset */
+#define chipcHw_REG_SOFT_RESET_ESW 0x0000004000000000ULL /* Reset Ethernet switch */
+#define chipcHw_REG_SOFT_RESET_ESWCLK 0x0000002000000000ULL /* Reset Ethernet switch clock */
+#define chipcHw_REG_SOFT_RESET_DDRPHY 0x0000001000000000ULL /* Reset DDR Physical */
+#define chipcHw_REG_SOFT_RESET_DDR 0x0000000800000000ULL /* Reset DDR Controller */
+#define chipcHw_REG_SOFT_RESET_TSC 0x0000000400000000ULL /* Reset Touch screen */
+#define chipcHw_REG_SOFT_RESET_PCM 0x0000000200000000ULL /* Reset PCM device */
+#define chipcHw_REG_SOFT_RESET_APM 0x0000200100000000ULL /* Reset APM device */
+
+#define chipcHw_REG_SOFT_RESET_VPM_GLOBAL_UNHOLD 0x8000000000000000ULL /* Unhold Global VPM */
+#define chipcHw_REG_SOFT_RESET_VPM_UNHOLD 0x4000000000000000ULL /* Unhold VPM */
+#define chipcHw_REG_SOFT_RESET_ARM_UNHOLD 0x2000000000000000ULL /* Unhold ARM reset */
+#define chipcHw_REG_SOFT_RESET_UNHOLD_MASK 0xF000000000000000ULL /* Mask to handle unhold request */
+
+/* Audio channel control defines */
+#define chipcHw_REG_AUDIO_CHANNEL_ENABLE_ALL 0x00000001 /* Enable all audio channel */
+#define chipcHw_REG_AUDIO_CHANNEL_ENABLE_A 0x00000002 /* Enable channel A */
+#define chipcHw_REG_AUDIO_CHANNEL_ENABLE_B 0x00000004 /* Enable channel B */
+#define chipcHw_REG_AUDIO_CHANNEL_ENABLE_C 0x00000008 /* Enable channel C */
+#define chipcHw_REG_AUDIO_CHANNEL_ENABLE_NTP_CLOCK 0x00000010 /* Enable NTP clock */
+#define chipcHw_REG_AUDIO_CHANNEL_ENABLE_PCM0_CLOCK 0x00000020 /* Enable PCM0 clock */
+#define chipcHw_REG_AUDIO_CHANNEL_ENABLE_PCM1_CLOCK 0x00000040 /* Enable PCM1 clock */
+#define chipcHw_REG_AUDIO_CHANNEL_ENABLE_APM_CLOCK 0x00000080 /* Enable APM clock */
+
+/* Misc. chip control defines */
+#define chipcHw_REG_MISC_CTRL_GE_SEL 0x00040000 /* Select GE2/GE3 */
+#define chipcHw_REG_MISC_CTRL_I2S1_CLOCK_ONCHIP 0x00000000 /* Use on chip clock for I2S1 */
+#define chipcHw_REG_MISC_CTRL_I2S1_CLOCK_GPIO 0x00020000 /* Use external clock via GPIO pin 26 for I2S1 */
+#define chipcHw_REG_MISC_CTRL_I2S0_CLOCK_ONCHIP 0x00000000 /* Use on chip clock for I2S0 */
+#define chipcHw_REG_MISC_CTRL_I2S0_CLOCK_GPIO 0x00010000 /* Use external clock via GPIO pin 45 for I2S0 */
+#define chipcHw_REG_MISC_CTRL_ARM_CP15_DISABLE 0x00008000 /* Disable ARM CP15 bit */
+#define chipcHw_REG_MISC_CTRL_RTC_DISABLE 0x00000008 /* Disable RTC registers */
+#define chipcHw_REG_MISC_CTRL_BBRAM_DISABLE 0x00000004 /* Disable Battery Backed RAM */
+#define chipcHw_REG_MISC_CTRL_USB_MODE_HOST 0x00000002 /* Set USB as host */
+#define chipcHw_REG_MISC_CTRL_USB_MODE_DEVICE 0xFFFFFFFD /* Set USB as device */
+#define chipcHw_REG_MISC_CTRL_USB_POWERON 0xFFFFFFFE /* Power up USB */
+#define chipcHw_REG_MISC_CTRL_USB_POWEROFF 0x00000001 /* Power down USB */
+
+/* OTP configuration defines */
+#define chipcHw_REG_OTP_SECURITY_OFF 0x0000020000000000ULL /* Security support is OFF */
+#define chipcHw_REG_OTP_SPU_SLOW 0x0000010000000000ULL /* Limited SPU throughput */
+#define chipcHw_REG_OTP_LCD_SPEED 0x0000000600000000ULL /* Set VPM speed one */
+#define chipcHw_REG_OTP_VPM_SPEED_1 0x0000000100000000ULL /* Set VPM speed one */
+#define chipcHw_REG_OTP_VPM_SPEED_0 0x0000000080000000ULL /* Set VPM speed zero */
+#define chipcHw_REG_OTP_AXI_SPEED 0x0000000060000000ULL /* Set maximum AXI bus speed */
+#define chipcHw_REG_OTP_APM_DISABLE 0x000000001F000000ULL /* Disable APM */
+#define chipcHw_REG_OTP_PIF_DISABLE 0x0000000000200000ULL /* Disable PIF */
+#define chipcHw_REG_OTP_VDEC_DISABLE 0x0000000000100000ULL /* Disable Video decoder */
+#define chipcHw_REG_OTP_BBL_DISABLE 0x0000000000080000ULL /* Disable RTC and BBRAM */
+#define chipcHw_REG_OTP_LED_DISABLE 0x0000000000040000ULL /* Disable LED */
+#define chipcHw_REG_OTP_GE_DISABLE 0x0000000000020000ULL /* Disable Graphics Engine */
+#define chipcHw_REG_OTP_LCD_DISABLE 0x0000000000010000ULL /* Disable LCD */
+#define chipcHw_REG_OTP_KEYPAD_DISABLE 0x0000000000008000ULL /* Disable keypad */
+#define chipcHw_REG_OTP_UART_DISABLE 0x0000000000004000ULL /* Disable UART */
+#define chipcHw_REG_OTP_SDIOH_DISABLE 0x0000000000003000ULL /* Disable SDIO host */
+#define chipcHw_REG_OTP_HSS_DISABLE 0x0000000000000C00ULL /* Disable HSS */
+#define chipcHw_REG_OTP_TSC_DISABLE 0x0000000000000200ULL /* Disable touch screen */
+#define chipcHw_REG_OTP_USB_DISABLE 0x0000000000000180ULL /* Disable USB */
+#define chipcHw_REG_OTP_SGMII_DISABLE 0x0000000000000060ULL /* Disable SGMII */
+#define chipcHw_REG_OTP_ETH_DISABLE 0x0000000000000018ULL /* Disable gigabit ethernet */
+#define chipcHw_REG_OTP_ETH_PHY_DISABLE 0x0000000000000006ULL /* Disable ethernet PHY */
+#define chipcHw_REG_OTP_VPM_DISABLE 0x0000000000000001ULL /* Disable VPM */
+
+/* Sticky bit defines */
+#define chipcHw_REG_STICKY_BOOT_DONE 0x00000001 /* Boot done */
+#define chipcHw_REG_STICKY_SOFT_RESET 0x00000002 /* ARM soft reset */
+#define chipcHw_REG_STICKY_GENERAL_1 0x00000004 /* General purpose bit 1 */
+#define chipcHw_REG_STICKY_GENERAL_2 0x00000008 /* General purpose bit 2 */
+#define chipcHw_REG_STICKY_GENERAL_3 0x00000010 /* General purpose bit 3 */
+#define chipcHw_REG_STICKY_GENERAL_4 0x00000020 /* General purpose bit 4 */
+#define chipcHw_REG_STICKY_GENERAL_5 0x00000040 /* General purpose bit 5 */
+#define chipcHw_REG_STICKY_POR_BROM 0x00000080 /* Special sticky bit for security - set in BROM to avoid other modes being entered */
+#define chipcHw_REG_STICKY_ARM_RESET 0x00000100 /* ARM reset */
+#define chipcHw_REG_STICKY_CHIP_SOFT_RESET 0x00000200 /* Chip soft reset */
+#define chipcHw_REG_STICKY_CHIP_WARM_RESET 0x00000400 /* Chip warm reset */
+#define chipcHw_REG_STICKY_WDOG_RESET 0x00000800 /* Watchdog reset */
+#define chipcHw_REG_STICKY_OTP_RESET 0x00001000 /* OTP reset */
+
+ /* HW phase alignment defines *//* Spare1 register definitions */
+#define chipcHw_REG_SPARE1_DDR_PHASE_INTR_ENABLE 0x80000000 /* Enable DDR phase align panic interrupt */
+#define chipcHw_REG_SPARE1_VPM_PHASE_INTR_ENABLE 0x40000000 /* Enable VPM phase align panic interrupt */
+#define chipcHw_REG_SPARE1_VPM_BUS_ACCESS_ENABLE 0x00000002 /* Enable access to VPM using system BUS */
+#define chipcHw_REG_SPARE1_DDR_BUS_ACCESS_ENABLE 0x00000001 /* Enable access to DDR using system BUS */
+ /* DDRPhaseCtrl1 register definitions */
+#define chipcHw_REG_DDR_SW_PHASE_CTRL_ENABLE 0x80000000 /* Enable DDR SW phase alignment */
+#define chipcHw_REG_DDR_HW_PHASE_CTRL_ENABLE 0x40000000 /* Enable DDR HW phase alignment */
+#define chipcHw_REG_DDR_PHASE_VALUE_GE_MASK 0x0000007F /* DDR lower threshold for phase alignment */
+#define chipcHw_REG_DDR_PHASE_VALUE_GE_SHIFT 23
+#define chipcHw_REG_DDR_PHASE_VALUE_LE_MASK 0x0000007F /* DDR upper threshold for phase alignment */
+#define chipcHw_REG_DDR_PHASE_VALUE_LE_SHIFT 16
+#define chipcHw_REG_DDR_PHASE_ALIGN_WAIT_CYCLE_MASK 0x0000FFFF /* BUS Cycle to wait to run next DDR phase alignment */
+#define chipcHw_REG_DDR_PHASE_ALIGN_WAIT_CYCLE_SHIFT 0
+ /* VPMPhaseCtrl1 register definitions */
+#define chipcHw_REG_VPM_SW_PHASE_CTRL_ENABLE 0x80000000 /* Enable VPM SW phase alignment */
+#define chipcHw_REG_VPM_HW_PHASE_CTRL_ENABLE 0x40000000 /* Enable VPM HW phase alignment */
+#define chipcHw_REG_VPM_PHASE_VALUE_GE_MASK 0x0000007F /* VPM lower threshold for phase alignment */
+#define chipcHw_REG_VPM_PHASE_VALUE_GE_SHIFT 23
+#define chipcHw_REG_VPM_PHASE_VALUE_LE_MASK 0x0000007F /* VPM upper threshold for phase alignment */
+#define chipcHw_REG_VPM_PHASE_VALUE_LE_SHIFT 16
+#define chipcHw_REG_VPM_PHASE_ALIGN_WAIT_CYCLE_MASK 0x0000FFFF /* BUS Cycle to wait to complete the VPM phase alignment */
+#define chipcHw_REG_VPM_PHASE_ALIGN_WAIT_CYCLE_SHIFT 0
+ /* PhaseAlignStatus register definitions */
+#define chipcHw_REG_DDR_TIMEOUT_INTR_STATUS 0x80000000 /* DDR time out interrupt status */
+#define chipcHw_REG_DDR_PHASE_STATUS_MASK 0x0000007F /* DDR phase status value */
+#define chipcHw_REG_DDR_PHASE_STATUS_SHIFT 24
+#define chipcHw_REG_DDR_PHASE_ALIGNED 0x00800000 /* DDR Phase aligned status */
+#define chipcHw_REG_DDR_LOAD 0x00400000 /* Load DDR phase status */
+#define chipcHw_REG_DDR_PHASE_CTRL_MASK 0x0000003F /* DDR phase control value */
+#define chipcHw_REG_DDR_PHASE_CTRL_SHIFT 16
+#define chipcHw_REG_VPM_TIMEOUT_INTR_STATUS 0x80000000 /* VPM time out interrupt status */
+#define chipcHw_REG_VPM_PHASE_STATUS_MASK 0x0000007F /* VPM phase status value */
+#define chipcHw_REG_VPM_PHASE_STATUS_SHIFT 8
+#define chipcHw_REG_VPM_PHASE_ALIGNED 0x00000080 /* VPM Phase aligned status */
+#define chipcHw_REG_VPM_LOAD 0x00000040 /* Load VPM phase status */
+#define chipcHw_REG_VPM_PHASE_CTRL_MASK 0x0000003F /* VPM phase control value */
+#define chipcHw_REG_VPM_PHASE_CTRL_SHIFT 0
+ /* DDRPhaseCtrl2 register definitions */
+#define chipcHw_REG_DDR_INTR_SERVICED 0x02000000 /* Acknowledge that interrupt was serviced */
+#define chipcHw_REG_DDR_TIMEOUT_INTR_ENABLE 0x01000000 /* Enable time out interrupt */
+#define chipcHw_REG_DDR_LOAD_COUNT_PHASE_CTRL_MASK 0x0000000F /* Wait before toggling load_ch */
+#define chipcHw_REG_DDR_LOAD_COUNT_PHASE_CTRL_SHIFT 20
+#define chipcHw_REG_DDR_TOTAL_LOAD_COUNT_CTRL_MASK 0x0000000F /* Total wait to settle ph_ctrl and load_ch */
+#define chipcHw_REG_DDR_TOTAL_LOAD_COUNT_CTRL_SHIFT 16
+#define chipcHw_REG_DDR_PHASE_TIMEOUT_COUNT_MASK 0x0000FFFF /* Time out value for DDR HW phase alignment */
+#define chipcHw_REG_DDR_PHASE_TIMEOUT_COUNT_SHIFT 0
+ /* VPMPhaseCtrl2 register definitions */
+#define chipcHw_REG_VPM_INTR_SELECT_MASK 0x00000003 /* Interrupt select */
+#define chipcHw_REG_VPM_INTR_SELECT_SHIFT 26
+#define chipcHw_REG_VPM_INTR_DISABLE 0x00000000
+#define chipcHw_REG_VPM_INTR_FAST (0x1 << chipcHw_REG_VPM_INTR_SELECT_SHIFT)
+#define chipcHw_REG_VPM_INTR_MEDIUM (0x2 << chipcHw_REG_VPM_INTR_SELECT_SHIFT)
+#define chipcHw_REG_VPM_INTR_SLOW (0x3 << chipcHw_REG_VPM_INTR_SELECT_SHIFT)
+#define chipcHw_REG_VPM_INTR_SERVICED 0x02000000 /* Acknowledge that interrupt was serviced */
+#define chipcHw_REG_VPM_TIMEOUT_INTR_ENABLE 0x01000000 /* Enable time out interrupt */
+#define chipcHw_REG_VPM_LOAD_COUNT_PHASE_CTRL_MASK 0x0000000F /* Wait before toggling load_ch */
+#define chipcHw_REG_VPM_LOAD_COUNT_PHASE_CTRL_SHIFT 20
+#define chipcHw_REG_VPM_TOTAL_LOAD_COUNT_CTRL_MASK 0x0000000F /* Total wait cycle to settle ph_ctrl and load_ch */
+#define chipcHw_REG_VPM_TOTAL_LOAD_COUNT_CTRL_SHIFT 16
+#define chipcHw_REG_VPM_PHASE_TIMEOUT_COUNT_MASK 0x0000FFFF /* Time out value for VPM HW phase alignment */
+#define chipcHw_REG_VPM_PHASE_TIMEOUT_COUNT_SHIFT 0
+
+#endif /* CHIPCHW_REG_H */
git.openpandora.org / pandora-kernel.git / commitdiff