.ucode_tracing = true,
.sensitivity_calib_by_driver = true,
.chain_noise_calib_by_driver = true,
- .supports_idle = true,
};
static struct iwl_ht_params iwl1000_ht_params = {
.ht_greenfield_support = true,
CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI |
CSR_HW_IF_CONFIG_REG_BIT_MAC_SI);
+ if (priv->cfg->iq_invert)
+ iwl_set_bit(priv, CSR_GP_DRIVER_REG,
+ CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER);
+
}
static struct iwl_sensitivity_ranges iwl2000_sensitivity = {
.shadow_ram_support = true,
.led_compensation = 51,
.chain_noise_num_beacons = IWL_CAL_NUM_BEACONS,
- .supports_idle = true,
.adv_thermal_throttle = true,
.support_ct_kill_exit = true,
.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
.shadow_ram_support = true,
.led_compensation = 57,
.chain_noise_num_beacons = IWL_CAL_NUM_BEACONS,
- .supports_idle = true,
.adv_thermal_throttle = true,
.support_ct_kill_exit = true,
.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
.base_params = &iwl2000_base_params, \
.need_dc_calib = true, \
.need_temp_offset_calib = true, \
- .led_mode = IWL_LED_RF_STATE \
+ .led_mode = IWL_LED_RF_STATE, \
+ .iq_invert = true \
struct iwl_cfg iwl2000_2bgn_cfg = {
.name = "2000 Series 2x2 BGN",
.need_dc_calib = true, \
.need_temp_offset_calib = true, \
.led_mode = IWL_LED_RF_STATE, \
- .adv_pm = true \
+ .adv_pm = true, \
+ .iq_invert = true \
struct iwl_cfg iwl2030_2bgn_cfg = {
.name = "2000 Series 2x2 BGN/BT",
- IWL_DEVICE_2000,
+ IWL_DEVICE_2030,
.ht_params = &iwl2000_ht_params,
};
struct iwl_cfg iwl2030_2bg_cfg = {
.name = "2000 Series 2x2 BG/BT",
- IWL_DEVICE_2000,
+ IWL_DEVICE_2030,
};
#define IWL_DEVICE_6035 \
*/
static void iwl4965_init_alive_start(struct iwl_priv *priv)
{
- /* Check alive response for "valid" sign from uCode */
- if (priv->card_alive_init.is_valid != UCODE_VALID_OK) {
- /* We had an error bringing up the hardware, so take it
- * all the way back down so we can try again */
- IWL_DEBUG_INFO(priv, "Initialize Alive failed.\n");
- goto restart;
- }
-
/* Bootstrap uCode has loaded initialize uCode ... verify inst image.
* This is a paranoid check, because we would not have gotten the
* "initialize" alive if code weren't properly loaded. */
spin_unlock_irqrestore(&priv->sta_lock, flags);
}
+static void iwl4965_rx_beacon_notif(struct iwl_priv *priv,
+ struct iwl_rx_mem_buffer *rxb)
+{
+ struct iwl_rx_packet *pkt = rxb_addr(rxb);
+ struct iwl4965_beacon_notif *beacon = (void *)pkt->u.raw;
+#ifdef CONFIG_IWLWIFI_DEBUG
+ u8 rate = iwl_hw_get_rate(beacon->beacon_notify_hdr.rate_n_flags);
+
+ IWL_DEBUG_RX(priv, "beacon status %#x, retries:%d ibssmgr:%d "
+ "tsf:0x%.8x%.8x rate:%d\n",
+ le32_to_cpu(beacon->beacon_notify_hdr.u.status) & TX_STATUS_MSK,
+ beacon->beacon_notify_hdr.failure_frame,
+ le32_to_cpu(beacon->ibss_mgr_status),
+ le32_to_cpu(beacon->high_tsf),
+ le32_to_cpu(beacon->low_tsf), rate);
+#endif
+
+ priv->ibss_manager = le32_to_cpu(beacon->ibss_mgr_status);
+
+ if (!test_bit(STATUS_EXIT_PENDING, &priv->status))
+ queue_work(priv->workqueue, &priv->beacon_update);
+}
+
static int iwl4965_calc_rssi(struct iwl_priv *priv,
struct iwl_rx_phy_res *rx_resp)
{
priv->rx_handlers[REPLY_RX] = iwlagn_rx_reply_rx;
/* Tx response */
priv->rx_handlers[REPLY_TX] = iwl4965_rx_reply_tx;
+ priv->rx_handlers[BEACON_NOTIFICATION] = iwl4965_rx_beacon_notif;
/* set up notification wait support */
spin_lock_init(&priv->_agn.notif_wait_lock);
.shadow_ram_support = true,
.led_compensation = 51,
.chain_noise_num_beacons = IWL_CAL_NUM_BEACONS,
- .supports_idle = true,
.adv_thermal_throttle = true,
.support_ct_kill_exit = true,
.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
.shadow_ram_support = true,
.led_compensation = 51,
.chain_noise_num_beacons = IWL_CAL_NUM_BEACONS,
- .supports_idle = true,
.adv_thermal_throttle = true,
.support_ct_kill_exit = true,
.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
.shadow_ram_support = true,
.led_compensation = 57,
.chain_noise_num_beacons = IWL_CAL_NUM_BEACONS,
- .supports_idle = true,
.adv_thermal_throttle = true,
.support_ct_kill_exit = true,
.plcp_delta_threshold = IWL_MAX_PLCP_ERR_THRESHOLD_DEF,
if (iwl_send_cmd_pdu(priv, REPLY_BT_CONFIG, sizeof(bt_cmd), &bt_cmd))
IWL_ERR(priv, "failed to send BT Coex Config\n");
- /*
- * When we are doing a restart, need to also reconfigure BT
- * SCO to the device. If not doing a restart, bt_sco_active
- * will always be false, so there's no need to have an extra
- * variable to check for it.
- */
- if (priv->bt_sco_active) {
- struct iwlagn_bt_sco_cmd sco_cmd = { .flags = 0 };
-
- if (priv->bt_sco_active)
- sco_cmd.flags |= IWLAGN_BT_SCO_ACTIVE;
- if (iwl_send_cmd_pdu(priv, REPLY_BT_COEX_SCO,
- sizeof(sco_cmd), &sco_cmd))
- IWL_ERR(priv, "failed to send BT SCO command\n");
- }
}
static void iwlagn_bt_traffic_change_work(struct work_struct *work)
unsigned long flags;
struct iwl_rx_packet *pkt = rxb_addr(rxb);
struct iwl_bt_coex_profile_notif *coex = &pkt->u.bt_coex_profile_notif;
- struct iwlagn_bt_sco_cmd sco_cmd = { .flags = 0 };
struct iwl_bt_uart_msg *uart_msg = &coex->last_bt_uart_msg;
IWL_DEBUG_NOTIF(priv, "BT Coex notification:\n");
queue_work(priv->workqueue,
&priv->bt_traffic_change_work);
}
- if (priv->bt_sco_active !=
- (uart_msg->frame3 & BT_UART_MSG_FRAME3SCOESCO_MSK)) {
- priv->bt_sco_active = uart_msg->frame3 &
- BT_UART_MSG_FRAME3SCOESCO_MSK;
- if (priv->bt_sco_active)
- sco_cmd.flags |= IWLAGN_BT_SCO_ACTIVE;
- iwl_send_cmd_pdu_async(priv, REPLY_BT_COEX_SCO,
- sizeof(sco_cmd), &sco_cmd, NULL);
- }
}
iwlagn_set_kill_msk(priv, uart_msg);
};
static s32 expected_tpt_siso20MHz[4][IWL_RATE_COUNT] = {
- {0, 0, 0, 0, 42, 0, 76, 102, 124, 158, 183, 193, 202}, /* Norm */
- {0, 0, 0, 0, 46, 0, 82, 110, 132, 167, 192, 202, 210}, /* SGI */
- {0, 0, 0, 0, 48, 0, 93, 135, 176, 251, 319, 351, 381}, /* AGG */
- {0, 0, 0, 0, 53, 0, 102, 149, 193, 275, 348, 381, 413}, /* AGG+SGI */
+ {0, 0, 0, 0, 42, 0, 76, 102, 124, 159, 183, 193, 202}, /* Norm */
+ {0, 0, 0, 0, 46, 0, 82, 110, 132, 168, 192, 202, 210}, /* SGI */
+ {0, 0, 0, 0, 47, 0, 91, 133, 171, 242, 305, 334, 362}, /* AGG */
+ {0, 0, 0, 0, 52, 0, 101, 145, 187, 264, 330, 361, 390}, /* AGG+SGI */
};
static s32 expected_tpt_siso40MHz[4][IWL_RATE_COUNT] = {
{0, 0, 0, 0, 77, 0, 127, 160, 184, 220, 242, 250, 257}, /* Norm */
{0, 0, 0, 0, 83, 0, 135, 169, 193, 229, 250, 257, 264}, /* SGI */
- {0, 0, 0, 0, 96, 0, 182, 259, 328, 451, 553, 598, 640}, /* AGG */
- {0, 0, 0, 0, 106, 0, 199, 282, 357, 487, 593, 640, 683}, /* AGG+SGI */
+ {0, 0, 0, 0, 94, 0, 177, 249, 313, 423, 512, 550, 586}, /* AGG */
+ {0, 0, 0, 0, 104, 0, 193, 270, 338, 454, 545, 584, 620}, /* AGG+SGI */
};
static s32 expected_tpt_mimo2_20MHz[4][IWL_RATE_COUNT] = {
- {0, 0, 0, 0, 74, 0, 123, 155, 179, 213, 235, 243, 250}, /* Norm */
- {0, 0, 0, 0, 81, 0, 131, 164, 187, 221, 242, 250, 256}, /* SGI */
- {0, 0, 0, 0, 92, 0, 175, 250, 317, 436, 534, 578, 619}, /* AGG */
- {0, 0, 0, 0, 102, 0, 192, 273, 344, 470, 573, 619, 660}, /* AGG+SGI*/
+ {0, 0, 0, 0, 74, 0, 123, 155, 179, 214, 236, 244, 251}, /* Norm */
+ {0, 0, 0, 0, 81, 0, 131, 164, 188, 223, 243, 251, 257}, /* SGI */
+ {0, 0, 0, 0, 89, 0, 167, 235, 296, 402, 488, 526, 560}, /* AGG */
+ {0, 0, 0, 0, 97, 0, 182, 255, 320, 431, 520, 558, 593}, /* AGG+SGI*/
};
static s32 expected_tpt_mimo2_40MHz[4][IWL_RATE_COUNT] = {
{0, 0, 0, 0, 123, 0, 182, 214, 235, 264, 279, 285, 289}, /* Norm */
{0, 0, 0, 0, 131, 0, 191, 222, 242, 270, 284, 289, 293}, /* SGI */
- {0, 0, 0, 0, 180, 0, 327, 446, 545, 708, 828, 878, 922}, /* AGG */
- {0, 0, 0, 0, 197, 0, 355, 481, 584, 752, 872, 922, 966}, /* AGG+SGI */
+ {0, 0, 0, 0, 171, 0, 305, 410, 496, 634, 731, 771, 805}, /* AGG */
+ {0, 0, 0, 0, 186, 0, 329, 439, 527, 667, 764, 803, 838}, /* AGG+SGI */
};
static s32 expected_tpt_mimo3_20MHz[4][IWL_RATE_COUNT] = {
u8 ant_toggle_cnt = 0;
u8 use_ht_possible = 1;
u8 valid_tx_ant = 0;
+ struct iwl_station_priv *sta_priv =
+ container_of(lq_sta, struct iwl_station_priv, lq_sta);
struct iwl_link_quality_cmd *lq_cmd = &lq_sta->lq;
/* Override starting rate (index 0) if needed for debug purposes */
repeat_rate--;
}
- lq_cmd->agg_params.agg_frame_cnt_limit = LINK_QUAL_AGG_FRAME_LIMIT_DEF;
+ lq_cmd->agg_params.agg_frame_cnt_limit =
+ sta_priv->max_agg_bufsize ?: LINK_QUAL_AGG_FRAME_LIMIT_DEF;
lq_cmd->agg_params.agg_dis_start_th = LINK_QUAL_AGG_DISABLE_START_DEF;
lq_cmd->agg_params.agg_time_limit =
{
int ret = 0;
- /* Check alive response for "valid" sign from uCode */
- if (priv->card_alive_init.is_valid != UCODE_VALID_OK) {
- /* We had an error bringing up the hardware, so take it
- * all the way back down so we can try again */
- IWL_DEBUG_INFO(priv, "Initialize Alive failed.\n");
- goto restart;
- }
-
/* initialize uCode was loaded... verify inst image.
* This is a paranoid check, because we would not have gotten the
* "initialize" alive if code weren't properly loaded. */
if (palive->is_valid == UCODE_VALID_OK)
queue_delayed_work(priv->workqueue, pwork,
msecs_to_jiffies(5));
- else
- IWL_WARN(priv, "uCode did not respond OK.\n");
+ else {
+ IWL_WARN(priv, "%s uCode did not respond OK.\n",
+ (palive->ver_subtype == INITIALIZE_SUBTYPE) ?
+ "init" : "runtime");
+ queue_work(priv->workqueue, &priv->restart);
+ }
}
static void iwl_bg_beacon_update(struct work_struct *work)
}
}
-static void iwl_rx_beacon_notif(struct iwl_priv *priv,
- struct iwl_rx_mem_buffer *rxb)
+static void iwlagn_rx_beacon_notif(struct iwl_priv *priv,
+ struct iwl_rx_mem_buffer *rxb)
{
struct iwl_rx_packet *pkt = rxb_addr(rxb);
- struct iwl4965_beacon_notif *beacon =
- (struct iwl4965_beacon_notif *)pkt->u.raw;
+ struct iwlagn_beacon_notif *beacon = (void *)pkt->u.raw;
#ifdef CONFIG_IWLWIFI_DEBUG
+ u16 status = le16_to_cpu(beacon->beacon_notify_hdr.status.status);
u8 rate = iwl_hw_get_rate(beacon->beacon_notify_hdr.rate_n_flags);
- IWL_DEBUG_RX(priv, "beacon status %x retries %d iss %d "
- "tsf %d %d rate %d\n",
- le32_to_cpu(beacon->beacon_notify_hdr.u.status) & TX_STATUS_MSK,
+ IWL_DEBUG_RX(priv, "beacon status %#x, retries:%d ibssmgr:%d "
+ "tsf:0x%.8x%.8x rate:%d\n",
+ status & TX_STATUS_MSK,
beacon->beacon_notify_hdr.failure_frame,
le32_to_cpu(beacon->ibss_mgr_status),
le32_to_cpu(beacon->high_tsf),
priv->rx_handlers[PM_SLEEP_NOTIFICATION] = iwl_rx_pm_sleep_notif;
priv->rx_handlers[PM_DEBUG_STATISTIC_NOTIFIC] =
iwl_rx_pm_debug_statistics_notif;
- priv->rx_handlers[BEACON_NOTIFICATION] = iwl_rx_beacon_notif;
+ priv->rx_handlers[BEACON_NOTIFICATION] = iwlagn_rx_beacon_notif;
/*
* The same handler is used for both the REPLY to a discrete
IWL_DEBUG_INFO(priv, "Runtime Alive received.\n");
- if (priv->card_alive.is_valid != UCODE_VALID_OK) {
- /* We had an error bringing up the hardware, so take it
- * all the way back down so we can try again */
- IWL_DEBUG_INFO(priv, "Alive failed.\n");
- goto restart;
- }
-
/* Initialize uCode has loaded Runtime uCode ... verify inst image.
* This is a paranoid check, because we would not have gotten the
* "runtime" alive if code weren't properly loaded. */
priv->cfg->bt_params->bt_init_traffic_load;
else
priv->bt_traffic_load = 0;
- priv->bt_sco_active = false;
priv->bt_full_concurrent = false;
priv->bt_ci_compliance = 0;
if (test_and_clear_bit(STATUS_FW_ERROR, &priv->status)) {
struct iwl_rxon_context *ctx;
- bool bt_sco, bt_full_concurrent;
+ bool bt_full_concurrent;
u8 bt_ci_compliance;
u8 bt_load;
u8 bt_status;
* re-configure the hw when we reconfigure the BT
* command.
*/
- bt_sco = priv->bt_sco_active;
bt_full_concurrent = priv->bt_full_concurrent;
bt_ci_compliance = priv->bt_ci_compliance;
bt_load = priv->bt_traffic_load;
__iwl_down(priv);
- priv->bt_sco_active = bt_sco;
priv->bt_full_concurrent = bt_full_concurrent;
priv->bt_ci_compliance = bt_ci_compliance;
priv->bt_traffic_load = bt_load;
IEEE80211_HW_SPECTRUM_MGMT |
IEEE80211_HW_REPORTS_TX_ACK_STATUS;
+ hw->max_tx_aggregation_subframes = LINK_QUAL_AGG_FRAME_LIMIT_DEF;
+
if (!priv->cfg->base_params->broken_powersave)
hw->flags |= IEEE80211_HW_SUPPORTS_PS |
IEEE80211_HW_SUPPORTS_DYNAMIC_PS;
hw->wiphy->max_remain_on_channel_duration = 1000;
hw->wiphy->flags |= WIPHY_FLAG_CUSTOM_REGULATORY |
- WIPHY_FLAG_DISABLE_BEACON_HINTS;
+ WIPHY_FLAG_DISABLE_BEACON_HINTS |
+ WIPHY_FLAG_IBSS_RSN;
/*
* For now, disable PS by default because it affects
return -EOPNOTSUPP;
}
+ /*
+ * To support IBSS RSN, don't program group keys in IBSS, the
+ * hardware will then not attempt to decrypt the frames.
+ */
+ if (vif->type == NL80211_IFTYPE_ADHOC &&
+ !(key->flags & IEEE80211_KEY_FLAG_PAIRWISE))
+ return -EOPNOTSUPP;
+
sta_id = iwl_sta_id_or_broadcast(priv, vif_priv->ctx, sta);
if (sta_id == IWL_INVALID_STATION)
return -EINVAL;
{
struct iwl_priv *priv = hw->priv;
int ret = -EINVAL;
+ struct iwl_station_priv *sta_priv = (void *) sta->drv_priv;
IWL_DEBUG_HT(priv, "A-MPDU action on addr %pM tid %d\n",
sta->addr, tid);
}
break;
case IEEE80211_AMPDU_TX_OPERATIONAL:
+ /*
+ * If the limit is 0, then it wasn't initialised yet,
+ * use the default. We can do that since we take the
+ * minimum below, and we don't want to go above our
+ * default due to hardware restrictions.
+ */
+ if (sta_priv->max_agg_bufsize == 0)
+ sta_priv->max_agg_bufsize =
+ LINK_QUAL_AGG_FRAME_LIMIT_DEF;
+
+ /*
+ * Even though in theory the peer could have different
+ * aggregation reorder buffer sizes for different sessions,
+ * our ucode doesn't allow for that and has a global limit
+ * for each station. Therefore, use the minimum of all the
+ * aggregation sessions and our default value.
+ */
+ sta_priv->max_agg_bufsize =
+ min(sta_priv->max_agg_bufsize, buf_size);
+
if (priv->cfg->ht_params &&
priv->cfg->ht_params->use_rts_for_aggregation) {
- struct iwl_station_priv *sta_priv =
- (void *) sta->drv_priv;
-
/*
* switch to RTS/CTS if it is the prefer protection
* method for HT traffic
sta_priv->lq_sta.lq.general_params.flags |=
LINK_QUAL_FLAGS_SET_STA_TLC_RTS_MSK;
- iwl_send_lq_cmd(priv, iwl_rxon_ctx_from_vif(vif),
- &sta_priv->lq_sta.lq, CMD_ASYNC, false);
}
+
+ sta_priv->lq_sta.lq.agg_params.agg_frame_cnt_limit =
+ sta_priv->max_agg_bufsize;
+
+ iwl_send_lq_cmd(priv, iwl_rxon_ctx_from_vif(vif),
+ &sta_priv->lq_sta.lq, CMD_ASYNC, false);
ret = 0;
break;
}
REPLY_BT_COEX_PRIO_TABLE = 0xcc,
REPLY_BT_COEX_PROT_ENV = 0xcd,
REPLY_BT_COEX_PROFILE_NOTIF = 0xce,
- REPLY_BT_COEX_SCO = 0xcf,
/* PAN commands */
REPLY_WIPAN_PARAMS = 0xb2,
__le32 ibss_mgr_status;
} __packed;
+struct iwlagn_beacon_notif {
+ struct iwlagn_tx_resp beacon_notify_hdr;
+ __le32 low_tsf;
+ __le32 high_tsf;
+ __le32 ibss_mgr_status;
+} __packed;
+
/*
* REPLY_TX_BEACON = 0x91 (command, has simple generic response)
*/
u16 led_compensation;
const bool broken_powersave;
int chain_noise_num_beacons;
- const bool supports_idle;
bool adv_thermal_throttle;
bool support_ct_kill_exit;
const bool support_wimax_coexist;
* @adv_pm: advance power management
* @rx_with_siso_diversity: 1x1 device with rx antenna diversity
* @internal_wimax_coex: internal wifi/wimax combo device
+ * @iq_invert: I/Q inversion
*
* We enable the driver to be backward compatible wrt API version. The
* driver specifies which APIs it supports (with @ucode_api_max being the
const bool adv_pm;
const bool rx_with_siso_diversity;
const bool internal_wimax_coex;
+ const bool iq_invert;
};
/***************************
#define CSR_GP_DRIVER_REG_BIT_CALIB_VERSION6 (0x00000004)
#define CSR_GP_DRIVER_REG_BIT_6050_1x2 (0x00000008)
+#define CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER (0x00000080)
+
/* GIO Chicken Bits (PCI Express bus link power management) */
#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
"last traffic notif: %d\n",
priv->bt_status ? "On" : "Off", priv->last_bt_traffic_load);
pos += scnprintf(buf + pos, bufsz - pos, "ch_announcement: %d, "
- "sco_active: %d, kill_ack_mask: %x, "
- "kill_cts_mask: %x\n",
- priv->bt_ch_announce, priv->bt_sco_active,
- priv->kill_ack_mask, priv->kill_cts_mask);
+ "kill_ack_mask: %x, kill_cts_mask: %x\n",
+ priv->bt_ch_announce, priv->kill_ack_mask,
+ priv->kill_cts_mask);
pos += scnprintf(buf + pos, bufsz - pos, "bluetooth traffic load: ");
switch (priv->bt_traffic_load) {
atomic_t pending_frames;
bool client;
bool asleep;
+ u8 max_agg_bufsize;
};
/**
u8 bt_status;
u8 bt_traffic_load, last_bt_traffic_load;
bool bt_ch_announce;
- bool bt_sco_active;
bool bt_full_concurrent;
bool bt_ant_couple_ok;
__le32 kill_ack_mask;
if (priv->cfg->base_params->broken_powersave)
iwl_power_sleep_cam_cmd(priv, cmd);
- else if (priv->cfg->base_params->supports_idle &&
- priv->hw->conf.flags & IEEE80211_CONF_IDLE)
+ else if (priv->hw->conf.flags & IEEE80211_CONF_IDLE)
iwl_static_sleep_cmd(priv, cmd, IWL_POWER_INDEX_5, 20);
else if (priv->cfg->ops->lib->tt_ops.lower_power_detection &&
priv->cfg->ops->lib->tt_ops.tt_power_mode &&
return -EOPNOTSUPP;
}
+ /*
+ * To support IBSS RSN, don't program group keys in IBSS, the
+ * hardware will then not attempt to decrypt the frames.
+ */
+ if (vif->type == NL80211_IFTYPE_ADHOC &&
+ !(key->flags & IEEE80211_KEY_FLAG_PAIRWISE))
+ return -EOPNOTSUPP;
+
static_key = !iwl_is_associated(priv, IWL_RXON_CTX_BSS);
if (!static_key) {
priv->contexts[IWL_RXON_CTX_BSS].interface_modes;
hw->wiphy->flags |= WIPHY_FLAG_CUSTOM_REGULATORY |
- WIPHY_FLAG_DISABLE_BEACON_HINTS;
+ WIPHY_FLAG_DISABLE_BEACON_HINTS |
+ WIPHY_FLAG_IBSS_RSN;
hw->wiphy->max_scan_ssids = PROBE_OPTION_MAX_3945;
/* we create the 802.11 header and a zero-length SSID element */
git.openpandora.org / pandora-kernel.git / commitdiff