hwmon: (w83627ehf) Improve support for W83667HG-B

Add support for 4th temperature sensor on W83677HG-B.
Display temperature labels on W83677HG-B to report temperature sources.

Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>

diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf
index 13d5561..0643019 100644 (file)
--- a/Documentation/hwmon/w83627ehf
+++ b/Documentation/hwmon/w83627ehf
@@ -39,16 +39,21 @@ This driver implements support for the Winbond W83627EHF, W83627EHG,
 W83627DHG, W83627DHG-P, W83667HG and W83667HG-B super I/O chips.
 We will refer to them collectively as Winbond chips.
 
-The chips implement three temperature sensors, five fan rotation
-speed sensors, ten analog voltage sensors (only nine for the 627DHG), one
-VID (6 pins for the 627EHF/EHG, 8 pins for the 627DHG and 667HG), alarms
-with beep warnings (control unimplemented), and some automatic fan
+The chips implement three temperature sensors (up to four for 667HG-B),
+five fan rotation speed sensors, ten analog voltage sensors (only nine for the
+627DHG), one VID (6 pins for the 627EHF/EHG, 8 pins for the 627DHG and 667HG),
+alarms with beep warnings (control unimplemented), and some automatic fan
 regulation strategies (plus manual fan control mode).
 
+The temperature sensor sources on W82677HG-B are configurable. temp4 is only
+reported if its temperature source differs from the temperature sources of the
+other three temperature sensors. The configured source for each of the
+temperature sensors is reported in tempX_label.
+
 Temperatures are measured in degrees Celsius and measurement resolution is 1
-degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
-the temperature gets higher than high limit; it stays on until the temperature
-falls below the hysteresis value.
+degC for temp1 and temp4, and 0.5 degC for temp2 and temp3. An alarm is
+triggered when the temperature gets higher than high limit; it stays on until
+the temperature falls below the hysteresis value.
 
 Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
 triggered if the rotation speed has dropped below a programmable limit. Fan

diff --git a/drivers/hwmon/w83627ehf.c b/drivers/hwmon/w83627ehf.c
index 5a627b9..d10fe70 100644 (file)
--- a/drivers/hwmon/w83627ehf.c
+++ b/drivers/hwmon/w83627ehf.c
@@ -39,7 +39,7 @@
     w83627dhg    9      5       4       3      0xa020 0xc1    0x5ca3
     w83627dhg-p  9      5       4       3      0xb070 0xc1    0x5ca3
     w83667hg     9      5       3       3      0xa510 0xc1    0x5ca3
-    w83667hg-b   9      5       3       3      0xb350 0xc1    0x5ca3
+    w83667hg-b   9      5       3       4      0xb350 0xc1    0x5ca3
 */
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
@@ -164,10 +164,10 @@ static const u16 W83627EHF_REG_FAN_MIN[] = { 0x3b, 0x3c, 0x3d, 0x3e, 0x55c };
 #define W83627EHF_REG_IN(nr)           ((nr < 7) ? (0x20 + (nr)) : \
                                         (0x550 + (nr) - 7))
 
-static const u16 W83627EHF_REG_TEMP[] = { 0x27, 0x150, 0x250 };
-static const u16 W83627EHF_REG_TEMP_HYST[] = { 0x3a, 0x153, 0x253 };
-static const u16 W83627EHF_REG_TEMP_OVER[] = { 0x39, 0x155, 0x255 };
-static const u16 W83627EHF_REG_TEMP_CONFIG[] = { 0, 0x152, 0x252 };
+static const u16 W83627EHF_REG_TEMP[] = { 0x27, 0x150, 0x250, 0x7e };
+static const u16 W83627EHF_REG_TEMP_HYST[] = { 0x3a, 0x153, 0x253, 0 };
+static const u16 W83627EHF_REG_TEMP_OVER[] = { 0x39, 0x155, 0x255, 0 };
+static const u16 W83627EHF_REG_TEMP_CONFIG[] = { 0, 0x152, 0x252, 0 };
 
 /* Fan clock dividers are spread over the following five registers */
 #define W83627EHF_REG_FANDIV1          0x47
@@ -213,6 +213,19 @@ static const u8 W83627EHF_REG_FAN_STEP_OUTPUT_COMMON[]
 static const u8 W83627EHF_REG_FAN_MAX_OUTPUT_W83667_B[] = { 0x67, 0x69, 0x6b };
 static const u8 W83627EHF_REG_FAN_STEP_OUTPUT_W83667_B[] = { 0x68, 0x6a, 0x6c };
 
+static const char *const w83667hg_b_temp_label[] = {
+       "SYSTIN",
+       "CPUTIN",
+       "AUXTIN",
+       "AMDTSI",
+       "PECI Agent 1",
+       "PECI Agent 2",
+       "PECI Agent 3",
+       "PECI Agent 4"
+};
+
+#define NUM_REG_TEMP   4
+
 static inline int is_word_sized(u16 reg)
 {
        return (((reg & 0xff00) == 0x100
@@ -294,6 +307,9 @@ struct w83627ehf_data {
        struct device *hwmon_dev;
        struct mutex lock;
 
+       u8 temp_src[NUM_REG_TEMP];
+       const char * const *temp_label;
+
        const u8 *REG_FAN_START_OUTPUT;
        const u8 *REG_FAN_STOP_OUTPUT;
        const u8 *REG_FAN_MAX_OUTPUT;
@@ -314,9 +330,9 @@ struct w83627ehf_data {
        u8 fan_div[5];
        u8 has_fan;             /* some fan inputs can be disabled */
        u8 temp_type[3];
-       s16 temp[3];
-       s16 temp_max[3];
-       s16 temp_max_hyst[3];
+       s16 temp[4];
+       s16 temp_max[4];
+       s16 temp_max_hyst[4];
        u32 alarms;
 
        u8 pwm_mode[4]; /* 0->DC variable voltage, 1->PWM variable duty cycle */
@@ -339,7 +355,7 @@ struct w83627ehf_data {
        u8 vid;
        u8 vrm;
 
-       u8 temp3_disable;
+       u8 have_temp;
        u8 in6_skip;
 };
 
@@ -577,12 +593,18 @@ static struct w83627ehf_data *w83627ehf_update_device(struct device *dev)
                }
 
                /* Measured temperatures and limits */
-               for (i = 0; i < 3; i++) {
-                       data->temp[i] = w83627ehf_read_value(data,
-                                       W83627EHF_REG_TEMP[i]);
-                       data->temp_max[i] = w83627ehf_read_value(data,
-                                           W83627EHF_REG_TEMP_OVER[i]);
-                       data->temp_max_hyst[i] = w83627ehf_read_value(data,
+               for (i = 0; i < NUM_REG_TEMP; i++) {
+                       if (!(data->have_temp & (1 << i)))
+                               continue;
+                       data->temp[i]
+                         = w83627ehf_read_value(data, W83627EHF_REG_TEMP[i]);
+                       if (i > 2)
+                               break;
+                       data->temp_max[i]
+                         = w83627ehf_read_value(data,
+                                                W83627EHF_REG_TEMP_OVER[i]);
+                       data->temp_max_hyst[i]
+                         = w83627ehf_read_value(data,
                                                 W83627EHF_REG_TEMP_HYST[i]);
                }
 
@@ -844,6 +866,15 @@ static struct sensor_device_attribute sda_fan_div[] = {
        SENSOR_ATTR(fan5_div, S_IRUGO, show_fan_div, NULL, 4),
 };
 
+static ssize_t
+show_temp_label(struct device *dev, struct device_attribute *attr, char *buf)
+{
+       struct w83627ehf_data *data = w83627ehf_update_device(dev);
+       struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+       int nr = sensor_attr->index;
+       return sprintf(buf, "%s\n", data->temp_label[data->temp_src[nr]]);
+}
+
 #define show_temp_reg(REG, reg) \
 static ssize_t \
 show_##reg(struct device *dev, struct device_attribute *attr, \
@@ -897,6 +928,14 @@ static struct sensor_device_attribute sda_temp_input[] = {
        SENSOR_ATTR(temp1_input, S_IRUGO, show_temp, NULL, 0),
        SENSOR_ATTR(temp2_input, S_IRUGO, show_temp, NULL, 1),
        SENSOR_ATTR(temp3_input, S_IRUGO, show_temp, NULL, 2),
+       SENSOR_ATTR(temp4_input, S_IRUGO, show_temp, NULL, 3),
+};
+
+static struct sensor_device_attribute sda_temp_label[] = {
+       SENSOR_ATTR(temp1_label, S_IRUGO, show_temp_label, NULL, 0),
+       SENSOR_ATTR(temp2_label, S_IRUGO, show_temp_label, NULL, 1),
+       SENSOR_ATTR(temp3_label, S_IRUGO, show_temp_label, NULL, 2),
+       SENSOR_ATTR(temp4_label, S_IRUGO, show_temp_label, NULL, 3),
 };
 
 static struct sensor_device_attribute sda_temp_max[] = {
@@ -1328,10 +1367,13 @@ static void w83627ehf_device_remove_files(struct device *dev)
                device_remove_file(dev, &sda_target_temp[i].dev_attr);
                device_remove_file(dev, &sda_tolerance[i].dev_attr);
        }
-       for (i = 0; i < 3; i++) {
-               if ((i == 2) && data->temp3_disable)
+       for (i = 0; i < NUM_REG_TEMP; i++) {
+               if (!(data->have_temp & (1 << i)))
                        continue;
                device_remove_file(dev, &sda_temp_input[i].dev_attr);
+               device_remove_file(dev, &sda_temp_label[i].dev_attr);
+               if (i > 2)
+                       break;
                device_remove_file(dev, &sda_temp_max[i].dev_attr);
                device_remove_file(dev, &sda_temp_max_hyst[i].dev_attr);
                device_remove_file(dev, &sda_temp_alarm[i].dev_attr);
@@ -1354,12 +1396,14 @@ static inline void __devinit w83627ehf_init_device(struct w83627ehf_data *data)
                w83627ehf_write_value(data, W83627EHF_REG_CONFIG,
                                      tmp | 0x01);
 
-       /* Enable temp2 and temp3 if needed */
-       for (i = 1; i < 3; i++) {
+       /* Enable temperature sensors if needed */
+       for (i = 0; i < NUM_REG_TEMP; i++) {
+               if (!(data->have_temp & (1 << i)))
+                       continue;
+               if (!W83627EHF_REG_TEMP_CONFIG[i])
+                       continue;
                tmp = w83627ehf_read_value(data,
                                           W83627EHF_REG_TEMP_CONFIG[i]);
-               if ((i == 2) && data->temp3_disable)
-                       continue;
                if (tmp & 0x01)
                        w83627ehf_write_value(data,
                                              W83627EHF_REG_TEMP_CONFIG[i],
@@ -1417,11 +1461,52 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
        data->pwm_num = (sio_data->kind == w83667hg
                         || sio_data->kind == w83667hg_b) ? 3 : 4;
 
+       data->have_temp = 0x07;
        /* Check temp3 configuration bit for 667HG */
-       if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) {
-               data->temp3_disable = w83627ehf_read_value(data,
-                                       W83627EHF_REG_TEMP_CONFIG[2]) & 0x01;
-               data->in6_skip = !data->temp3_disable;
+       if (sio_data->kind == w83667hg) {
+               u8 reg;
+
+               reg = w83627ehf_read_value(data, W83627EHF_REG_TEMP_CONFIG[2]);
+               if (reg & 0x01)
+                       data->have_temp &= ~(1 << 2);
+               else
+                       data->in6_skip = 1; /* Either temp3 or in6 */
+       } else if (sio_data->kind == w83667hg_b) {
+               u8 reg;
+
+               reg = w83627ehf_read_value(data, 0x4a);
+               data->temp_src[0] = reg >> 5;
+               reg = w83627ehf_read_value(data, 0x49);
+               data->temp_src[1] = reg & 0x07;
+               data->temp_src[2] = (reg >> 4)  & 0x07;
+
+               /*
+                * W83667HG-B has another temperature register at 0x7e.
+                * The temperature source is selected with register 0x7d.
+                * Support it if the source differs from already reported
+                * sources.
+                */
+               reg = w83627ehf_read_value(data, 0x7d);
+               reg &= 0x07;
+               if (reg != data->temp_src[0] && reg != data->temp_src[1]
+                   && reg != data->temp_src[2]) {
+                       data->temp_src[3] = reg;
+                       data->have_temp |= 1 << 3;
+               }
+
+               /*
+                * Chip supports either AUXTIN or VIN3. Try to find out which
+                * one.
+                */
+               reg = w83627ehf_read_value(data, W83627EHF_REG_TEMP_CONFIG[2]);
+               if (data->temp_src[2] == 2 && (reg & 0x01))
+                       data->have_temp &= ~(1 << 2);
+
+               if ((data->temp_src[2] == 2 && (data->have_temp & (1 << 2)))
+                   || (data->temp_src[3] == 2 && (data->have_temp & (1 << 3))))
+                       data->in6_skip = 1;
+
+               data->temp_label = w83667hg_b_temp_label;
        }
 
        data->REG_FAN_START_OUTPUT = W83627EHF_REG_FAN_START_OUTPUT;
@@ -1584,13 +1669,21 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
                }
        }
 
-       for (i = 0; i < 3; i++) {
-               if ((i == 2) && data->temp3_disable)
+       for (i = 0; i < NUM_REG_TEMP; i++) {
+               if (!(data->have_temp & (1 << i)))
                        continue;
-               if ((err = device_create_file(dev,
-                               &sda_temp_input[i].dev_attr))
-                       || (err = device_create_file(dev,
-                               &sda_temp_max[i].dev_attr))
+               err = device_create_file(dev, &sda_temp_input[i].dev_attr);
+               if (err)
+                       goto exit_remove;
+               if (data->temp_label) {
+                       err = device_create_file(dev,
+                                                &sda_temp_label[i].dev_attr);
+                       if (err)
+                               goto exit_remove;
+               }
+               if (i > 2)
+                       break;
+               if ((err = device_create_file(dev, &sda_temp_max[i].dev_attr))
                        || (err = device_create_file(dev,
                                &sda_temp_max_hyst[i].dev_attr))
                        || (err = device_create_file(dev,