[ARM] 3154/1: SharpSL PM Driver updates

Patch from Richard Purdie

Updates to the SharpSL PM driver including cleanups from both
Pavel Machek and myself and updates after the platform device
changes to make it compile again.

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

diff --git a/arch/arm/mach-pxa/sharpsl.h b/arch/arm/mach-pxa/sharpsl.h
index 4879c0f..b0c40a1 100644 (file)
--- a/arch/arm/mach-pxa/sharpsl.h
+++ b/arch/arm/mach-pxa/sharpsl.h
@@ -115,7 +115,7 @@ extern struct battery_thresh spitz_battery_levels_noac[];
 #define CHARGE_LED_ERR()    sharpsl_pm.machinfo->chargeled(SHARPSL_LED_ERROR)
 #define DISCHARGE_ON()      sharpsl_pm.machinfo->discharge(1)
 #define DISCHARGE_OFF()     sharpsl_pm.machinfo->discharge(0)
-#define STATUS_AC_IN        sharpsl_pm.machinfo->status_acin()
-#define STATUS_BATT_LOCKED  READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batlock)
-#define STATUS_CHRG_FULL    READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batfull)
-#define STATUS_FATAL        READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_fatal)
+#define STATUS_AC_IN()      sharpsl_pm.machinfo->status_acin()
+#define STATUS_BATT_LOCKED()  READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batlock)
+#define STATUS_CHRG_FULL()  READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batfull)
+#define STATUS_FATAL()      READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_fatal)

diff --git a/arch/arm/mach-pxa/sharpsl_pm.c b/arch/arm/mach-pxa/sharpsl_pm.c
index 6c9e871..c10be00 100644 (file)
--- a/arch/arm/mach-pxa/sharpsl_pm.c
+++ b/arch/arm/mach-pxa/sharpsl_pm.c
@@ -21,7 +21,7 @@
 #include <linux/apm_bios.h>
 #include <linux/delay.h>
 #include <linux/interrupt.h>
-#include <linux/device.h>
+#include <linux/platform_device.h>
 
 #include <asm/hardware.h>
 #include <asm/hardware/scoop.h>
@@ -45,15 +45,15 @@
 #define SHARPSL_WAIT_DISCHARGE_ON              100 /* 100 msec */
 #define SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP   10  /* 10 msec */
 #define SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT   10  /* 10 msec */
-#define SHARPSL_CHECK_BATTERY_WAIT_TIME_JKVAD  10  /* 10 msec */
+#define SHARPSL_CHECK_BATTERY_WAIT_TIME_ACIN   10  /* 10 msec */
 #define SHARPSL_CHARGE_WAIT_TIME               15  /* 15 msec */
 #define SHARPSL_CHARGE_CO_CHECK_TIME           5   /* 5 msec */
 #define SHARPSL_CHARGE_RETRY_CNT               1   /* eqv. 10 min */
 
 #define SHARPSL_CHARGE_ON_VOLT         0x99  /* 2.9V */
 #define SHARPSL_CHARGE_ON_TEMP         0xe0  /* 2.9V */
-#define SHARPSL_CHARGE_ON_JKVAD_HIGH   0x9b  /* 6V */
-#define SHARPSL_CHARGE_ON_JKVAD_LOW    0x34  /* 2V */
+#define SHARPSL_CHARGE_ON_ACIN_HIGH    0x9b  /* 6V */
+#define SHARPSL_CHARGE_ON_ACIN_LOW     0x34  /* 2V */
 #define SHARPSL_FATAL_ACIN_VOLT        182   /* 3.45V */
 #define SHARPSL_FATAL_NOACIN_VOLT      170   /* 3.40V */
 
@@ -160,9 +160,10 @@ struct battery_thresh  spitz_battery_levels_noac[] = {
 /*
  * Prototypes
  */
-static int sharpsl_read_MainBattery(void);
+static int sharpsl_read_main_battery(void);
 static int sharpsl_off_charge_battery(void);
-static int sharpsl_check_battery(int mode);
+static int sharpsl_check_battery_temp(void);
+static int sharpsl_check_battery_voltage(void);
 static int sharpsl_ac_check(void);
 static int sharpsl_fatal_check(void);
 static int sharpsl_average_value(int ad);
@@ -228,7 +229,7 @@ static void sharpsl_battery_thread(void *private_)
        if (!sharpsl_pm.machinfo)
                return;
 
-       sharpsl_pm.battstat.ac_status = (!(STATUS_AC_IN) ? APM_AC_OFFLINE : APM_AC_ONLINE);
+       sharpsl_pm.battstat.ac_status = (STATUS_AC_IN() ? APM_AC_ONLINE : APM_AC_OFFLINE);
 
        /* Corgi cannot confirm when battery fully charged so periodically kick! */
        if (machine_is_corgi() && (sharpsl_pm.charge_mode == CHRG_ON)
@@ -236,7 +237,7 @@ static void sharpsl_battery_thread(void *private_)
                schedule_work(&toggle_charger);
 
        while(1) {
-               voltage = sharpsl_read_MainBattery();
+               voltage = sharpsl_read_main_battery();
                if (voltage > 0) break;
                if (i++ > 5) {
                        voltage = sharpsl_pm.machinfo->bat_levels_noac[0].voltage;
@@ -317,10 +318,10 @@ static void sharpsl_charge_toggle(void *private_)
 {
        dev_dbg(sharpsl_pm.dev, "Toogling Charger at time: %lx\n", jiffies);
 
-       if (STATUS_AC_IN == 0) {
+       if (STATUS_AC_IN() == 0) {
                sharpsl_charge_off();
                return;
-       } else if ((sharpsl_check_battery(1) < 0) || (sharpsl_ac_check() < 0)) {
+       } else if ((sharpsl_check_battery_temp() < 0) || (sharpsl_ac_check() < 0)) {
                sharpsl_charge_error();
                return;
        }
@@ -335,7 +336,7 @@ static void sharpsl_charge_toggle(void *private_)
 
 static void sharpsl_ac_timer(unsigned long data)
 {
-       int acin = STATUS_AC_IN;
+       int acin = STATUS_AC_IN();
 
        dev_dbg(sharpsl_pm.dev, "AC Status: %d\n",acin);
 
@@ -364,7 +365,7 @@ static void sharpsl_chrg_full_timer(unsigned long data)
 
        sharpsl_pm.full_count++;
 
-       if (STATUS_AC_IN == 0) {
+       if (STATUS_AC_IN() == 0) {
                dev_dbg(sharpsl_pm.dev, "Charge Full: AC removed - stop charging!\n");
                if (sharpsl_pm.charge_mode == CHRG_ON)
                        sharpsl_charge_off();
@@ -399,12 +400,12 @@ static irqreturn_t sharpsl_fatal_isr(int irq, void *dev_id, struct pt_regs *fp)
 {
        int is_fatal = 0;
 
-       if (STATUS_BATT_LOCKED == 0) {
+       if (STATUS_BATT_LOCKED() == 0) {
                dev_err(sharpsl_pm.dev, "Battery now Unlocked! Suspending.\n");
                is_fatal = 1;
        }
 
-       if (sharpsl_pm.machinfo->gpio_fatal && (STATUS_FATAL == 0)) {
+       if (sharpsl_pm.machinfo->gpio_fatal && (STATUS_FATAL() == 0)) {
                dev_err(sharpsl_pm.dev, "Fatal Batt Error! Suspending.\n");
                is_fatal = 1;
        }
@@ -461,12 +462,12 @@ static int read_max1111(int channel)
                        | MAXCTRL_SGL | MAXCTRL_UNI | MAXCTRL_STR);
 }
 
-static int sharpsl_read_MainBattery(void)
+static int sharpsl_read_main_battery(void)
 {
        return read_max1111(BATT_AD);
 }
 
-static int sharpsl_read_Temp(void)
+static int sharpsl_read_temp(void)
 {
        int temp;
 
@@ -480,7 +481,7 @@ static int sharpsl_read_Temp(void)
        return temp;
 }
 
-static int sharpsl_read_jkvad(void)
+static int sharpsl_read_acin(void)
 {
        return read_max1111(JK_VAD);
 }
@@ -522,16 +523,14 @@ static int get_select_val(int *val)
        return (sum/3);
 }
 
-/*  mode 0 - Check temperature and voltage
- *       1 - Check temperature only */
-static int sharpsl_check_battery(int mode)
+static int sharpsl_check_battery_temp(void)
 {
        int val, i, buff[5];
 
        /* Check battery temperature */
        for (i=0; i<5; i++) {
                mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_TEMP);
-               buff[i] = sharpsl_read_Temp();
+               buff[i] = sharpsl_read_temp();
        }
 
        val = get_select_val(buff);
@@ -539,8 +538,13 @@ static int sharpsl_check_battery(int mode)
        dev_dbg(sharpsl_pm.dev, "Temperature: %d\n", val);
        if (val > SHARPSL_CHARGE_ON_TEMP)
                return -1;
-       if (mode == 1)
-               return 0;
+
+       return 0;
+}
+
+static int sharpsl_check_battery_voltage(void)
+{
+       int val, i, buff[5];
 
        /* disable charge, enable discharge */
        CHARGE_OFF();
@@ -552,7 +556,7 @@ static int sharpsl_check_battery(int mode)
 
        /* Check battery voltage */
        for (i=0; i<5; i++) {
-               buff[i] = sharpsl_read_MainBattery();
+               buff[i] = sharpsl_read_main_battery();
                mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT);
        }
 
@@ -575,14 +579,14 @@ static int sharpsl_ac_check(void)
        int temp, i, buff[5];
 
        for (i=0; i<5; i++) {
-               buff[i] = sharpsl_read_jkvad();
-               mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_JKVAD);
+               buff[i] = sharpsl_read_acin();
+               mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_ACIN);
        }
 
        temp = get_select_val(buff);
        dev_dbg(sharpsl_pm.dev, "AC Voltage: %d\n",temp);
 
-       if ((temp > SHARPSL_CHARGE_ON_JKVAD_HIGH) || (temp < SHARPSL_CHARGE_ON_JKVAD_LOW)) {
+       if ((temp > SHARPSL_CHARGE_ON_ACIN_HIGH) || (temp < SHARPSL_CHARGE_ON_ACIN_LOW)) {
                dev_err(sharpsl_pm.dev, "Error: AC check failed.\n");
                return -1;
        }
@@ -591,7 +595,7 @@ static int sharpsl_ac_check(void)
 }
 
 #ifdef CONFIG_PM
-static int sharpsl_pm_suspend(struct device *dev, pm_message_t state)
+static int sharpsl_pm_suspend(struct platform_device *pdev, pm_message_t state)
 {
        sharpsl_pm.flags |= SHARPSL_SUSPENDED;
        flush_scheduled_work();
@@ -604,7 +608,7 @@ static int sharpsl_pm_suspend(struct device *dev, pm_message_t state)
        return 0;
 }
 
-static int sharpsl_pm_resume(struct device *dev)
+static int sharpsl_pm_resume(struct platform_device *pdev)
 {
        /* Clear the reset source indicators as they break the bootloader upon reboot */
        RCSR = 0x0f;
@@ -622,7 +626,7 @@ static void corgi_goto_sleep(unsigned long alarm_time, unsigned int alarm_enable
        dev_dbg(sharpsl_pm.dev, "Offline Charge Activate = %d\n",sharpsl_pm.flags & SHARPSL_DO_OFFLINE_CHRG);
        /* not charging and AC-IN! */
 
-       if ((sharpsl_pm.flags & SHARPSL_DO_OFFLINE_CHRG) && (STATUS_AC_IN != 0)) {
+       if ((sharpsl_pm.flags & SHARPSL_DO_OFFLINE_CHRG) && (STATUS_AC_IN() != 0)) {
                dev_dbg(sharpsl_pm.dev, "Activating Offline Charger...\n");
                sharpsl_pm.charge_mode = CHRG_OFF;
                sharpsl_pm.flags &= ~SHARPSL_DO_OFFLINE_CHRG;
@@ -671,7 +675,7 @@ static int corgi_enter_suspend(unsigned long alarm_time, unsigned int alarm_enab
                dev_dbg(sharpsl_pm.dev, "User triggered wakeup in offline charger.\n");
        }
 
-       if ((STATUS_BATT_LOCKED == 0) || (sharpsl_fatal_check() < 0) )
+       if ((STATUS_BATT_LOCKED() == 0) || (sharpsl_fatal_check() < 0) )
        {
                dev_err(sharpsl_pm.dev, "Fatal condition. Suspend.\n");
                corgi_goto_sleep(alarm_time, alarm_enable, state);
@@ -711,7 +715,7 @@ static int sharpsl_fatal_check(void)
        dev_dbg(sharpsl_pm.dev, "sharpsl_fatal_check entered\n");
 
        /* Check AC-Adapter */
-       acin = STATUS_AC_IN;
+       acin = STATUS_AC_IN();
 
        if (acin && (sharpsl_pm.charge_mode == CHRG_ON)) {
                CHARGE_OFF();
@@ -725,7 +729,7 @@ static int sharpsl_fatal_check(void)
 
        /* Check battery : check inserting battery ? */
        for (i=0; i<5; i++) {
-               buff[i] = sharpsl_read_MainBattery();
+               buff[i] = sharpsl_read_main_battery();
                mdelay(SHARPSL_CHECK_BATTERY_WAIT_TIME_VOLT);
        }
 
@@ -739,7 +743,7 @@ static int sharpsl_fatal_check(void)
        }
 
        temp = get_select_val(buff);
-       dev_dbg(sharpsl_pm.dev, "sharpsl_fatal_check: acin: %d, discharge voltage: %d, no discharge: %d\n", acin, temp, sharpsl_read_MainBattery());
+       dev_dbg(sharpsl_pm.dev, "sharpsl_fatal_check: acin: %d, discharge voltage: %d, no discharge: %d\n", acin, temp, sharpsl_read_main_battery());
 
        if ((acin && (temp < SHARPSL_FATAL_ACIN_VOLT)) ||
                        (!acin && (temp < SHARPSL_FATAL_NOACIN_VOLT)))
@@ -771,7 +775,7 @@ static int sharpsl_off_charge_battery(void)
                dev_dbg(sharpsl_pm.dev, "Offline Charger: Step 1\n");
 
                /* AC Check */
-               if ((sharpsl_ac_check() < 0) || (sharpsl_check_battery(1) < 0))
+               if ((sharpsl_ac_check() < 0) || (sharpsl_check_battery_temp() < 0))
                        return sharpsl_off_charge_error();
 
                /* Start Charging */
@@ -793,7 +797,7 @@ static int sharpsl_off_charge_battery(void)
 
                dev_dbg(sharpsl_pm.dev, "Offline Charger: Step 2\n");
 
-               if (sharpsl_check_battery(0) < 0)
+               if ((sharpsl_check_battery_temp() < 0) || (sharpsl_check_battery_voltage() < 0))
                        return sharpsl_off_charge_error();
 
                CHARGE_OFF();
@@ -811,7 +815,7 @@ static int sharpsl_off_charge_battery(void)
                        /* Check for timeout */
                        if ((RCNR - time) > SHARPSL_WAIT_CO_TIME)
                                return 1;
-                       if (STATUS_CHRG_FULL) {
+                       if (STATUS_CHRG_FULL()) {
                                dev_dbg(sharpsl_pm.dev, "Offline Charger: Charge full occured. Retrying to check\n");
                                sharpsl_pm.full_count++;
                                CHARGE_OFF();
@@ -840,7 +844,7 @@ static int sharpsl_off_charge_battery(void)
                        sharpsl_pm.full_count++;
                        return 1;
                }
-               if (STATUS_CHRG_FULL) {
+               if (STATUS_CHRG_FULL()) {
                        dev_dbg(sharpsl_pm.dev, "Offline Charger: Charging complete.\n");
                        CHARGE_LED_OFF();
                        CHARGE_OFF();
@@ -886,13 +890,13 @@ static struct pm_ops sharpsl_pm_ops = {
        .finish         = pxa_pm_finish,
 };
 
-static int __init sharpsl_pm_probe(struct device *dev)
+static int __init sharpsl_pm_probe(struct platform_device *pdev)
 {
-       if (!dev->platform_data)
+       if (!pdev->dev.platform_data)
                return -EINVAL;
 
-       sharpsl_pm.dev = dev;
-       sharpsl_pm.machinfo = dev->platform_data;
+       sharpsl_pm.dev = &pdev->dev;
+       sharpsl_pm.machinfo = pdev->dev.platform_data;
        sharpsl_pm.charge_mode = CHRG_OFF;
        sharpsl_pm.flags = 0;
 
@@ -935,8 +939,8 @@ static int __init sharpsl_pm_probe(struct device *dev)
                else set_irq_type(IRQ_GPIO(sharpsl_pm.machinfo->gpio_batfull),IRQT_RISING);
        }
 
-       device_create_file(dev, &dev_attr_battery_percentage);
-       device_create_file(dev, &dev_attr_battery_voltage);
+       device_create_file(&pdev->dev, &dev_attr_battery_percentage);
+       device_create_file(&pdev->dev, &dev_attr_battery_voltage);
 
        apm_get_power_status = sharpsl_apm_get_power_status;
 
@@ -947,12 +951,12 @@ static int __init sharpsl_pm_probe(struct device *dev)
        return 0;
 }
 
-static int sharpsl_pm_remove(struct device *dev)
+static int sharpsl_pm_remove(struct platform_device *pdev)
 {
        pm_set_ops(NULL);
 
-       device_remove_file(dev, &dev_attr_battery_percentage);
-       device_remove_file(dev, &dev_attr_battery_voltage);
+       device_remove_file(&pdev->dev, &dev_attr_battery_percentage);
+       device_remove_file(&pdev->dev, &dev_attr_battery_voltage);
 
        free_irq(IRQ_GPIO(sharpsl_pm.machinfo->gpio_acin), sharpsl_ac_isr);
        free_irq(IRQ_GPIO(sharpsl_pm.machinfo->gpio_batlock), sharpsl_fatal_isr);
@@ -969,23 +973,24 @@ static int sharpsl_pm_remove(struct device *dev)
        return 0;
 }
 
-static struct device_driver sharpsl_pm_driver = {
-       .name           = "sharpsl-pm",
-       .bus            = &platform_bus_type,
+static struct platform_driver sharpsl_pm_driver = {
        .probe          = sharpsl_pm_probe,
        .remove         = sharpsl_pm_remove,
        .suspend        = sharpsl_pm_suspend,
        .resume         = sharpsl_pm_resume,
+       .driver         = {
+               .name           = "sharpsl-pm",
+       },
 };
 
 static int __devinit sharpsl_pm_init(void)
 {
-       return driver_register(&sharpsl_pm_driver);
+       return platform_driver_register(&sharpsl_pm_driver);
 }
 
 static void sharpsl_pm_exit(void)
 {
-       driver_unregister(&sharpsl_pm_driver);
+       platform_driver_unregister(&sharpsl_pm_driver);
 }
 
 late_initcall(sharpsl_pm_init);