* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
usb: ftdi_sio: add PID for Propox ISPcable III
Revert "xHCI: reset-on-resume quirk for NEC uPD720200"
xHCI: fix bug in xhci_clear_command_ring()
usb: gadget: fsl_udc: fix dequeuing a request in progress
usb: fsl_mxc_udc.c: Remove compile-time dependency of MX35 SoC type
usb: fsl_mxc_udc.c: Fix build issue by including missing header file
USB: fsl_udc_core: use usb_endpoint_xfer_isoc to judge ISO XFER
usb: udc: Fix gadget driver's speed check in various UDC drivers
usb: gadget: fix g_serial regression
usb: renesas_usbhs: fixup driver speed
usb: renesas_usbhs: fixup gadget.dev.driver when udc_stop.
usb: renesas_usbhs: fixup signal the driver that cable was disconnected
usb: renesas_usbhs: fixup device_register timing
usb: musb: PM: fix context save/restore in suspend/resume path
USB: linux-cdc-acm.inf: add support for the acm_ms gadget
EHCI : Fix a regression in the ISO scheduler
xHCI: reset-on-resume quirk for NEC uPD720200
USB: whci-hcd: fix endian conversion in qset_clear()
USB: usb-storage: unusual_devs entry for Kingston DT 101 G2
usb: option: add SIMCom SIM5218
...
[SourceDisksFiles]
[SourceDisksNames]
[DeviceList]
-%DESCRIPTION%=DriverInstall, USB\VID_0525&PID_A4A7, USB\VID_1D6B&PID_0104&MI_02
+%DESCRIPTION%=DriverInstall, USB\VID_0525&PID_A4A7, USB\VID_1D6B&PID_0104&MI_02, USB\VID_1D6B&PID_0106&MI_00
[DeviceList.NTamd64]
-%DESCRIPTION%=DriverInstall, USB\VID_0525&PID_A4A7, USB\VID_1D6B&PID_0104&MI_02
+%DESCRIPTION%=DriverInstall, USB\VID_0525&PID_A4A7, USB\VID_1D6B&PID_0104&MI_02, USB\VID_1D6B&PID_0106&MI_00
;------------------------------------------------------------------------------
u32 tmp;
if (!driver || !bind || !driver->setup
- || driver->speed != USB_SPEED_HIGH)
+ || driver->speed < USB_SPEED_HIGH)
return -EINVAL;
if (!dev)
return -ENODEV;
}
if (!gser->port.in->desc || !gser->port.out->desc) {
DBG(cdev, "activate generic ttyGS%d\n", gser->port_num);
- if (!config_ep_by_speed(cdev->gadget, f, gser->port.in) ||
- !config_ep_by_speed(cdev->gadget, f, gser->port.out)) {
+ if (config_ep_by_speed(cdev->gadget, f, gser->port.in) ||
+ config_ep_by_speed(cdev->gadget, f, gser->port.out)) {
gser->port.in->desc = NULL;
gser->port.out->desc = NULL;
return -EINVAL;
#include <linux/err.h>
#include <linux/fsl_devices.h>
#include <linux/platform_device.h>
+#include <linux/io.h>
#include <mach/hardware.h>
void fsl_udc_clk_finalize(struct platform_device *pdev)
{
struct fsl_usb2_platform_data *pdata = pdev->dev.platform_data;
-#if defined(CONFIG_SOC_IMX35)
if (cpu_is_mx35()) {
unsigned int v;
USBPHYCTRL_OTGBASE_OFFSET));
}
}
-#endif
/* ULPI transceivers don't need usbpll */
if (pdata->phy_mode == FSL_USB2_PHY_ULPI) {
if (!udc_controller)
return -ENODEV;
- if (!driver || (driver->speed != USB_SPEED_FULL
- && driver->speed != USB_SPEED_HIGH)
+ if (!driver || driver->speed < USB_SPEED_FULL
|| !bind || !driver->disconnect || !driver->setup)
return -EINVAL;
kfree(req);
}
-/*-------------------------------------------------------------------------*/
+/* Actually add a dTD chain to an empty dQH and let go */
+static void fsl_prime_ep(struct fsl_ep *ep, struct ep_td_struct *td)
+{
+ struct ep_queue_head *qh = get_qh_by_ep(ep);
+
+ /* Write dQH next pointer and terminate bit to 0 */
+ qh->next_dtd_ptr = cpu_to_hc32(td->td_dma
+ & EP_QUEUE_HEAD_NEXT_POINTER_MASK);
+
+ /* Clear active and halt bit */
+ qh->size_ioc_int_sts &= cpu_to_hc32(~(EP_QUEUE_HEAD_STATUS_ACTIVE
+ | EP_QUEUE_HEAD_STATUS_HALT));
+
+ /* Ensure that updates to the QH will occur before priming. */
+ wmb();
+
+ /* Prime endpoint by writing correct bit to ENDPTPRIME */
+ fsl_writel(ep_is_in(ep) ? (1 << (ep_index(ep) + 16))
+ : (1 << (ep_index(ep))), &dr_regs->endpointprime);
+}
+
+/* Add dTD chain to the dQH of an EP */
static void fsl_queue_td(struct fsl_ep *ep, struct fsl_req *req)
{
- int i = ep_index(ep) * 2 + ep_is_in(ep);
u32 temp, bitmask, tmp_stat;
- struct ep_queue_head *dQH = &ep->udc->ep_qh[i];
/* VDBG("QH addr Register 0x%8x", dr_regs->endpointlistaddr);
VDBG("ep_qh[%d] addr is 0x%8x", i, (u32)&(ep->udc->ep_qh[i])); */
cpu_to_hc32(req->head->td_dma & DTD_ADDR_MASK);
/* Read prime bit, if 1 goto done */
if (fsl_readl(&dr_regs->endpointprime) & bitmask)
- goto out;
+ return;
do {
/* Set ATDTW bit in USBCMD */
fsl_writel(temp & ~USB_CMD_ATDTW, &dr_regs->usbcmd);
if (tmp_stat)
- goto out;
+ return;
}
- /* Write dQH next pointer and terminate bit to 0 */
- temp = req->head->td_dma & EP_QUEUE_HEAD_NEXT_POINTER_MASK;
- dQH->next_dtd_ptr = cpu_to_hc32(temp);
-
- /* Clear active and halt bit */
- temp = cpu_to_hc32(~(EP_QUEUE_HEAD_STATUS_ACTIVE
- | EP_QUEUE_HEAD_STATUS_HALT));
- dQH->size_ioc_int_sts &= temp;
-
- /* Ensure that updates to the QH will occur before priming. */
- wmb();
-
- /* Prime endpoint by writing 1 to ENDPTPRIME */
- temp = ep_is_in(ep)
- ? (1 << (ep_index(ep) + 16))
- : (1 << (ep_index(ep)));
- fsl_writel(temp, &dr_regs->endpointprime);
-out:
- return;
+ fsl_prime_ep(ep, req->head);
}
/* Fill in the dTD structure
VDBG("%s, bad ep", __func__);
return -EINVAL;
}
- if (ep->desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) {
+ if (usb_endpoint_xfer_isoc(ep->desc)) {
if (req->req.length > ep->ep.maxpacket)
return -EMSGSIZE;
}
/* The request isn't the last request in this ep queue */
if (req->queue.next != &ep->queue) {
- struct ep_queue_head *qh;
struct fsl_req *next_req;
- qh = ep->qh;
next_req = list_entry(req->queue.next, struct fsl_req,
queue);
- /* Point the QH to the first TD of next request */
- fsl_writel((u32) next_req->head, &qh->curr_dtd_ptr);
+ /* prime with dTD of next request */
+ fsl_prime_ep(ep, next_req->head);
}
-
- /* The request hasn't been processed, patch up the TD chain */
+ /* The request hasn't been processed, patch up the TD chain */
} else {
struct fsl_req *prev_req;
prev_req = list_entry(req->queue.prev, struct fsl_req, queue);
- fsl_writel(fsl_readl(&req->tail->next_td_ptr),
- &prev_req->tail->next_td_ptr);
-
+ prev_req->tail->next_td_ptr = req->tail->next_td_ptr;
}
done(ep, req, -ECONNRESET);
goto out;
}
- if (ep->desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) {
+ if (usb_endpoint_xfer_isoc(ep->desc)) {
status = -EOPNOTSUPP;
goto out;
}
struct fsl_udc *udc;
int size = 0;
u32 bitmask;
- struct ep_queue_head *d_qh;
+ struct ep_queue_head *qh;
ep = container_of(_ep, struct fsl_ep, ep);
if (!_ep || (!ep->desc && ep_index(ep) != 0))
if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN)
return -ESHUTDOWN;
- d_qh = &ep->udc->ep_qh[ep_index(ep) * 2 + ep_is_in(ep)];
+ qh = get_qh_by_ep(ep);
bitmask = (ep_is_in(ep)) ? (1 << (ep_index(ep) + 16)) :
(1 << (ep_index(ep)));
if (fsl_readl(&dr_regs->endptstatus) & bitmask)
- size = (d_qh->size_ioc_int_sts & DTD_PACKET_SIZE)
+ size = (qh->size_ioc_int_sts & DTD_PACKET_SIZE)
>> DTD_LENGTH_BIT_POS;
pr_debug("%s %u\n", __func__, size);
if (!udc_controller)
return -ENODEV;
- if (!driver || (driver->speed != USB_SPEED_FULL
- && driver->speed != USB_SPEED_HIGH)
+ if (!driver || driver->speed < USB_SPEED_FULL
|| !bind || !driver->disconnect || !driver->setup)
return -EINVAL;
* 2 + ((windex & USB_DIR_IN) ? 1 : 0))
#define get_pipe_by_ep(EP) (ep_index(EP) * 2 + ep_is_in(EP))
+static inline struct ep_queue_head *get_qh_by_ep(struct fsl_ep *ep)
+{
+ /* we only have one ep0 structure but two queue heads */
+ if (ep_index(ep) != 0)
+ return ep->qh;
+ else
+ return &ep->udc->ep_qh[(ep->udc->ep0_dir ==
+ USB_DIR_IN) ? 1 : 0];
+}
+
struct platform_device;
#ifdef CONFIG_ARCH_MXC
int fsl_udc_clk_init(struct platform_device *pdev);
int retval;
if (!driver
- || driver->speed != USB_SPEED_HIGH
+ || driver->speed < USB_SPEED_HIGH
|| !bind
|| !driver->setup)
return -EINVAL;
* (dev->usb->xcvrdiag & FORCE_FULL_SPEED_MODE)
* "must not be used in normal operation"
*/
- if (!driver || driver->speed != USB_SPEED_HIGH
+ if (!driver || driver->speed < USB_SPEED_HIGH
|| !driver->setup)
return -EINVAL;
struct r8a66597 *r8a66597 = gadget_to_r8a66597(gadget);
if (!driver
- || driver->speed != USB_SPEED_HIGH
+ || driver->speed < USB_SPEED_HIGH
|| !driver->setup)
return -EINVAL;
if (!r8a66597)
return -EINVAL;
}
- if (driver->speed != USB_SPEED_HIGH &&
- driver->speed != USB_SPEED_FULL) {
+ if (driver->speed < USB_SPEED_FULL)
dev_err(hsotg->dev, "%s: bad speed\n", __func__);
- }
if (!bind || !driver->setup) {
dev_err(hsotg->dev, "%s: missing entry points\n", __func__);
int ret;
if (!driver
- || (driver->speed != USB_SPEED_FULL &&
- driver->speed != USB_SPEED_HIGH)
+ || driver->speed < USB_SPEED_FULL
|| !bind
|| !driver->unbind || !driver->disconnect || !driver->setup)
return -EINVAL;
* jump until after the queue is primed.
*/
else {
+ int done = 0;
start = SCHEDULE_SLOP + (now & ~0x07);
/* NOTE: assumes URB_ISO_ASAP, to limit complexity/bugs */
if (stream->highspeed) {
if (itd_slot_ok(ehci, mod, start,
stream->usecs, period))
- break;
+ done = 1;
} else {
if ((start % 8) >= 6)
continue;
if (sitd_slot_ok(ehci, mod, stream,
start, sched, period))
- break;
+ done = 1;
}
- } while (start > next);
+ } while (start > next && !done);
/* no room in the schedule */
- if (start == next) {
+ if (!done) {
ehci_dbg(ehci, "iso resched full %p (now %d max %d)\n",
urb, now, now + mod);
status = -ENOSPC;
{
qset->td_start = qset->td_end = qset->ntds = 0;
- qset->qh.link = cpu_to_le32(QH_LINK_NTDS(8) | QH_LINK_T);
+ qset->qh.link = cpu_to_le64(QH_LINK_NTDS(8) | QH_LINK_T);
qset->qh.status = qset->qh.status & QH_STATUS_SEQ_MASK;
qset->qh.err_count = 0;
qset->qh.scratch[0] = 0;
ring = xhci->cmd_ring;
seg = ring->deq_seg;
do {
- memset(seg->trbs, 0, SEGMENT_SIZE);
+ memset(seg->trbs, 0,
+ sizeof(union xhci_trb) * (TRBS_PER_SEGMENT - 1));
+ seg->trbs[TRBS_PER_SEGMENT - 1].link.control &=
+ cpu_to_le32(~TRB_CYCLE);
seg = seg->next;
} while (seg != ring->deq_seg);
*/
}
- musb_save_context(musb);
-
spin_unlock_irqrestore(&musb->lock, flags);
return 0;
}
static int musb_resume_noirq(struct device *dev)
{
- struct musb *musb = dev_to_musb(dev);
-
- musb_restore_context(musb);
-
/* for static cmos like DaVinci, register values were preserved
* unless for some reason the whole soc powered down or the USB
* module got reset through the PSC (vs just being disabled).
unsigned long flags;
int retval = -EINVAL;
- if (driver->speed != USB_SPEED_HIGH)
+ if (driver->speed < USB_SPEED_HIGH)
goto err0;
pm_runtime_get_sync(musb->controller);
struct usb_gadget_driver *driver)
{
struct usbhsg_gpriv *gpriv = usbhsg_gadget_to_gpriv(gadget);
- struct usbhs_priv *priv;
- struct device *dev;
- int ret;
+ struct usbhs_priv *priv = usbhsg_gpriv_to_priv(gpriv);
if (!driver ||
!driver->setup ||
- driver->speed != USB_SPEED_HIGH)
+ driver->speed < USB_SPEED_FULL)
return -EINVAL;
- dev = usbhsg_gpriv_to_dev(gpriv);
- priv = usbhsg_gpriv_to_priv(gpriv);
-
/* first hook up the driver ... */
gpriv->driver = driver;
gpriv->gadget.dev.driver = &driver->driver;
- ret = device_add(&gpriv->gadget.dev);
- if (ret) {
- dev_err(dev, "device_add error %d\n", ret);
- goto add_fail;
- }
-
return usbhsg_try_start(priv, USBHSG_STATUS_REGISTERD);
-
-add_fail:
- gpriv->driver = NULL;
- gpriv->gadget.dev.driver = NULL;
-
- return ret;
}
static int usbhsg_gadget_stop(struct usb_gadget *gadget,
struct usb_gadget_driver *driver)
{
struct usbhsg_gpriv *gpriv = usbhsg_gadget_to_gpriv(gadget);
- struct usbhs_priv *priv;
- struct device *dev;
+ struct usbhs_priv *priv = usbhsg_gpriv_to_priv(gpriv);
if (!driver ||
!driver->unbind)
return -EINVAL;
- dev = usbhsg_gpriv_to_dev(gpriv);
- priv = usbhsg_gpriv_to_priv(gpriv);
-
usbhsg_try_stop(priv, USBHSG_STATUS_REGISTERD);
- device_del(&gpriv->gadget.dev);
+ gpriv->gadget.dev.driver = NULL;
gpriv->driver = NULL;
return 0;
static int usbhsg_stop(struct usbhs_priv *priv)
{
+ struct usbhsg_gpriv *gpriv = usbhsg_priv_to_gpriv(priv);
+
+ /* cable disconnect */
+ if (gpriv->driver &&
+ gpriv->driver->disconnect)
+ gpriv->driver->disconnect(&gpriv->gadget);
+
return usbhsg_try_stop(priv, USBHSG_STATUS_STARTED);
}
/*
* init gadget
*/
- device_initialize(&gpriv->gadget.dev);
dev_set_name(&gpriv->gadget.dev, "gadget");
gpriv->gadget.dev.parent = dev;
gpriv->gadget.name = "renesas_usbhs_udc";
gpriv->gadget.ops = &usbhsg_gadget_ops;
gpriv->gadget.is_dualspeed = 1;
+ ret = device_register(&gpriv->gadget.dev);
+ if (ret < 0)
+ goto err_add_udc;
INIT_LIST_HEAD(&gpriv->gadget.ep_list);
ret = usb_add_gadget_udc(dev, &gpriv->gadget);
if (ret)
- goto err_add_udc;
+ goto err_register;
dev_info(dev, "gadget probed\n");
return 0;
+
+err_register:
+ device_unregister(&gpriv->gadget.dev);
err_add_udc:
kfree(gpriv->uep);
usb_del_gadget_udc(&gpriv->gadget);
+ device_unregister(&gpriv->gadget.dev);
+
usbhsg_controller_unregister(gpriv);
kfree(gpriv->uep);
{ USB_DEVICE(TML_VID, TML_USB_SERIAL_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_ELSTER_UNICOM_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_PROPOX_JTAGCABLEII_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_PROPOX_ISPCABLEIII_PID) },
{ USB_DEVICE(OLIMEX_VID, OLIMEX_ARM_USB_OCD_PID),
.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
{ USB_DEVICE(OLIMEX_VID, OLIMEX_ARM_USB_OCD_H_PID),
/* Propox devices */
#define FTDI_PROPOX_JTAGCABLEII_PID 0xD738
+#define FTDI_PROPOX_ISPCABLEIII_PID 0xD739
/* Lenz LI-USB Computer Interface. */
#define FTDI_LENZ_LIUSB_PID 0xD780
{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4511, 0xff, 0x01, 0x31) },
{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_K4511, 0xff, 0x01, 0x32) },
{ USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E353, 0xff, 0x01, 0x01) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E353, 0xff, 0x01, 0x02) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E353, 0xff, 0x01, 0x03) },
+ { USB_DEVICE_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E353, 0xff, 0x01, 0x08) },
{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V640) },
{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V620) },
{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID, NOVATELWIRELESS_PRODUCT_V740) },
{ USB_DEVICE(KYOCERA_VENDOR_ID, KYOCERA_PRODUCT_KPC680) },
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6000)}, /* ZTE AC8700 */
{ USB_DEVICE(QUALCOMM_VENDOR_ID, 0x6613)}, /* Onda H600/ZTE MF330 */
+ { USB_DEVICE(QUALCOMM_VENDOR_ID, 0x9000)}, /* SIMCom SIM5218 */
{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6280) }, /* BP3-USB & BP3-EXT HSDPA */
{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6008) },
{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_UC864E) },
USB_SC_DEVICE, USB_PR_DEVICE, NULL,
US_FL_IGNORE_RESIDUE ),
+/* Reported by Qinglin Ye <yestyle@gmail.com> */
+UNUSUAL_DEV( 0x13fe, 0x3600, 0x0100, 0x0100,
+ "Kingston",
+ "DT 101 G2",
+ USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+ US_FL_BULK_IGNORE_TAG ),
+
/* Reported by Francesco Foresti <frafore@tiscali.it> */
UNUSUAL_DEV( 0x14cd, 0x6600, 0x0201, 0x0201,
"Super Top",
git.openpandora.org / pandora-kernel.git / commitdiff