MIPS: Alchemy: Rewrite UART setup and constants.

Detect CPU type at runtime and setup uarts accordingly; also clean up the
uart base address mess in the process as far as possible.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org

diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index 9e7814d..36489fb 100644 (file)
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -30,21 +30,12 @@ static void alchemy_8250_pm(struct uart_port *port, unsigned int state,
 #ifdef CONFIG_SERIAL_8250
        switch (state) {
        case 0:
-               if ((__raw_readl(port->membase + UART_MOD_CNTRL) & 3) != 3) {
-                       /* power-on sequence as suggested in the databooks */
-                       __raw_writel(0, port->membase + UART_MOD_CNTRL);
-                       wmb();
-                       __raw_writel(1, port->membase + UART_MOD_CNTRL);
-                       wmb();
-               }
-               __raw_writel(3, port->membase + UART_MOD_CNTRL); /* full on */
-               wmb();
+               alchemy_uart_enable(CPHYSADDR(port->membase));
                serial8250_do_pm(port, state, old_state);
                break;
        case 3:         /* power off */
                serial8250_do_pm(port, state, old_state);
-               __raw_writel(0, port->membase + UART_MOD_CNTRL);
-               wmb();
+               alchemy_uart_disable(CPHYSADDR(port->membase));
                break;
        default:
                serial8250_do_pm(port, state, old_state);
@@ -65,38 +56,60 @@ static void alchemy_8250_pm(struct uart_port *port, unsigned int state,
                .pm             = alchemy_8250_pm,              \
        }
 
-static struct plat_serial8250_port au1x00_uart_data[] = {
-#if defined(CONFIG_SOC_AU1000)
-       PORT(UART0_PHYS_ADDR, AU1000_UART0_INT),
-       PORT(UART1_PHYS_ADDR, AU1000_UART1_INT),
-       PORT(UART2_PHYS_ADDR, AU1000_UART2_INT),
-       PORT(UART3_PHYS_ADDR, AU1000_UART3_INT),
-#elif defined(CONFIG_SOC_AU1500)
-       PORT(UART0_PHYS_ADDR, AU1500_UART0_INT),
-       PORT(UART3_PHYS_ADDR, AU1500_UART3_INT),
-#elif defined(CONFIG_SOC_AU1100)
-       PORT(UART0_PHYS_ADDR, AU1100_UART0_INT),
-       PORT(UART1_PHYS_ADDR, AU1100_UART1_INT),
-       PORT(UART3_PHYS_ADDR, AU1100_UART3_INT),
-#elif defined(CONFIG_SOC_AU1550)
-       PORT(UART0_PHYS_ADDR, AU1550_UART0_INT),
-       PORT(UART1_PHYS_ADDR, AU1550_UART1_INT),
-       PORT(UART3_PHYS_ADDR, AU1550_UART3_INT),
-#elif defined(CONFIG_SOC_AU1200)
-       PORT(UART0_PHYS_ADDR, AU1200_UART0_INT),
-       PORT(UART1_PHYS_ADDR, AU1200_UART1_INT),
-#endif
-       { },
+static struct plat_serial8250_port au1x00_uart_data[][4] __initdata = {
+       [ALCHEMY_CPU_AU1000] = {
+               PORT(AU1000_UART0_PHYS_ADDR, AU1000_UART0_INT),
+               PORT(AU1000_UART1_PHYS_ADDR, AU1000_UART1_INT),
+               PORT(AU1000_UART2_PHYS_ADDR, AU1000_UART2_INT),
+               PORT(AU1000_UART3_PHYS_ADDR, AU1000_UART3_INT),
+       },
+       [ALCHEMY_CPU_AU1500] = {
+               PORT(AU1000_UART0_PHYS_ADDR, AU1500_UART0_INT),
+               PORT(AU1000_UART3_PHYS_ADDR, AU1500_UART3_INT),
+       },
+       [ALCHEMY_CPU_AU1100] = {
+               PORT(AU1000_UART0_PHYS_ADDR, AU1100_UART0_INT),
+               PORT(AU1000_UART1_PHYS_ADDR, AU1100_UART1_INT),
+               PORT(AU1000_UART3_PHYS_ADDR, AU1100_UART3_INT),
+       },
+       [ALCHEMY_CPU_AU1550] = {
+               PORT(AU1000_UART0_PHYS_ADDR, AU1550_UART0_INT),
+               PORT(AU1000_UART1_PHYS_ADDR, AU1550_UART1_INT),
+               PORT(AU1000_UART3_PHYS_ADDR, AU1550_UART3_INT),
+       },
+       [ALCHEMY_CPU_AU1200] = {
+               PORT(AU1000_UART0_PHYS_ADDR, AU1200_UART0_INT),
+               PORT(AU1000_UART1_PHYS_ADDR, AU1200_UART1_INT),
+       },
 };
 
 static struct platform_device au1xx0_uart_device = {
        .name                   = "serial8250",
        .id                     = PLAT8250_DEV_AU1X00,
-       .dev                    = {
-               .platform_data  = au1x00_uart_data,
-       },
 };
 
+static void __init alchemy_setup_uarts(int ctype)
+{
+       unsigned int uartclk = get_au1x00_uart_baud_base() * 16;
+       int s = sizeof(struct plat_serial8250_port);
+       int c = alchemy_get_uarts(ctype);
+       struct plat_serial8250_port *ports;
+
+       ports = kzalloc(s * (c + 1), GFP_KERNEL);
+       if (!ports) {
+               printk(KERN_INFO "Alchemy: no memory for UART data\n");
+               return;
+       }
+       memcpy(ports, au1x00_uart_data[ctype], s * c);
+       au1xx0_uart_device.dev.platform_data = ports;
+
+       /* Fill up uartclk. */
+       for (s = 0; s < c; s++)
+               ports[s].uartclk = uartclk;
+       if (platform_device_register(&au1xx0_uart_device))
+               printk(KERN_INFO "Alchemy: failed to register UARTs\n");
+}
+
 /* OHCI (USB full speed host controller) */
 static struct resource au1xxx_usb_ohci_resources[] = {
        [0] = {
@@ -442,7 +455,6 @@ void __init au1xxx_override_eth_cfg(unsigned int port,
 }
 
 static struct platform_device *au1xxx_platform_devices[] __initdata = {
-       &au1xx0_uart_device,
        &au1xxx_usb_ohci_device,
 #ifdef CONFIG_FB_AU1100
        &au1100_lcd_device,
@@ -465,13 +477,10 @@ static struct platform_device *au1xxx_platform_devices[] __initdata = {
 
 static int __init au1xxx_platform_init(void)
 {
-       unsigned int uartclk = get_au1x00_uart_baud_base() * 16;
-       int err, i;
+       int err, i, ctype = alchemy_get_cputype();
        unsigned char ethaddr[6];
 
-       /* Fill up uartclk. */
-       for (i = 0; au1x00_uart_data[i].flags; i++)
-               au1x00_uart_data[i].uartclk = uartclk;
+       alchemy_setup_uarts(ctype);
 
        /* use firmware-provided mac addr if available and necessary */
        i = prom_get_ethernet_addr(ethaddr);

diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index baeb213..e5306b5 100644 (file)
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -62,5 +62,5 @@ void __init prom_init(void)
 
 void prom_putchar(unsigned char c)
 {
-    alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+       alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
 }

diff --git a/arch/mips/alchemy/gpr/board_setup.c b/arch/mips/alchemy/gpr/board_setup.c
index ad2e3f1..5f8f069 100644 (file)
--- a/arch/mips/alchemy/gpr/board_setup.c
+++ b/arch/mips/alchemy/gpr/board_setup.c
@@ -36,9 +36,6 @@
 
 #include <prom.h>
 
-#define UART1_ADDR     KSEG1ADDR(UART1_PHYS_ADDR)
-#define UART3_ADDR     KSEG1ADDR(UART3_PHYS_ADDR)
-
 char irq_tab_alchemy[][5] __initdata = {
        [0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff },
 };
@@ -67,18 +64,15 @@ static void gpr_power_off(void)
 
 void __init board_setup(void)
 {
-       printk(KERN_INFO "Tarpeze ITS GPR board\n");
+       printk(KERN_INFO "Trapeze ITS GPR board\n");
 
        pm_power_off = gpr_power_off;
        _machine_halt = gpr_power_off;
        _machine_restart = gpr_reset;
 
-       /* Enable UART3 */
-       au_writel(0x1, UART3_ADDR + UART_MOD_CNTRL);/* clock enable (CE) */
-       au_writel(0x3, UART3_ADDR + UART_MOD_CNTRL); /* CE and "enable" */
-       /* Enable UART1 */
-       au_writel(0x1, UART1_ADDR + UART_MOD_CNTRL); /* clock enable (CE) */
-       au_writel(0x3, UART1_ADDR + UART_MOD_CNTRL); /* CE and "enable" */
+       /* Enable UART1/3 */
+       alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+       alchemy_uart_enable(AU1000_UART1_PHYS_ADDR);
 
        /* Take away Reset of UMTS-card */
        alchemy_gpio_direction_output(215, 1);

diff --git a/arch/mips/alchemy/gpr/init.c b/arch/mips/alchemy/gpr/init.c
index f044f4c..229aafa 100644 (file)
--- a/arch/mips/alchemy/gpr/init.c
+++ b/arch/mips/alchemy/gpr/init.c
@@ -59,5 +59,5 @@ void __init prom_init(void)
 
 void prom_putchar(unsigned char c)
 {
-       alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+       alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
 }

diff --git a/arch/mips/alchemy/mtx-1/init.c b/arch/mips/alchemy/mtx-1/init.c
index f8d2557..2e81cc7 100644 (file)
--- a/arch/mips/alchemy/mtx-1/init.c
+++ b/arch/mips/alchemy/mtx-1/init.c
@@ -62,5 +62,5 @@ void __init prom_init(void)
 
 void prom_putchar(unsigned char c)
 {
-       alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+       alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
 }

diff --git a/arch/mips/alchemy/xxs1500/board_setup.c b/arch/mips/alchemy/xxs1500/board_setup.c
index febfb0f..81e57fa 100644 (file)
--- a/arch/mips/alchemy/xxs1500/board_setup.c
+++ b/arch/mips/alchemy/xxs1500/board_setup.c
@@ -66,13 +66,10 @@ void __init board_setup(void)
        au_writel(pin_func, SYS_PINFUNC);
 
        /* Enable UART */
-       au_writel(0x01, UART3_ADDR + UART_MOD_CNTRL); /* clock enable (CE) */
-       mdelay(10);
-       au_writel(0x03, UART3_ADDR + UART_MOD_CNTRL); /* CE and "enable" */
-       mdelay(10);
-
-       /* Enable DTR = USB power up */
-       au_writel(0x01, UART3_ADDR + UART_MCR); /* UART_MCR_DTR is 0x01??? */
+       alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+       /* Enable DTR (MCR bit 0) = USB power up */
+       __raw_writel(1, (void __iomem *)KSEG1ADDR(AU1000_UART3_PHYS_ADDR + 0x18));
+       wmb();
 
 #ifdef CONFIG_PCI
 #if defined(__MIPSEB__)

diff --git a/arch/mips/alchemy/xxs1500/init.c b/arch/mips/alchemy/xxs1500/init.c
index 34a90a4..0ee02cf 100644 (file)
--- a/arch/mips/alchemy/xxs1500/init.c
+++ b/arch/mips/alchemy/xxs1500/init.c
@@ -59,5 +59,5 @@ void __init prom_init(void)
 
 void prom_putchar(unsigned char c)
 {
-       alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+       alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
 }

diff --git a/arch/mips/boot/compressed/uart-alchemy.c b/arch/mips/boot/compressed/uart-alchemy.c
index 1bff22f..eb063e6 100644 (file)
--- a/arch/mips/boot/compressed/uart-alchemy.c
+++ b/arch/mips/boot/compressed/uart-alchemy.c
@@ -3,5 +3,5 @@
 void putc(char c)
 {
        /* all current (Jan. 2010) in-kernel boards */
-       alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+       alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
 }

diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h
index eb8f103..c4ffb20 100644 (file)
--- a/arch/mips/include/asm/mach-au1x00/au1000.h
+++ b/arch/mips/include/asm/mach-au1x00/au1000.h
@@ -161,6 +161,45 @@ static inline int alchemy_get_cputype(void)
        return ALCHEMY_CPU_UNKNOWN;
 }
 
+/* return number of uarts on a given cputype */
+static inline int alchemy_get_uarts(int type)
+{
+       switch (type) {
+       case ALCHEMY_CPU_AU1000:
+               return 4;
+       case ALCHEMY_CPU_AU1500:
+       case ALCHEMY_CPU_AU1200:
+               return 2;
+       case ALCHEMY_CPU_AU1100:
+       case ALCHEMY_CPU_AU1550:
+               return 3;
+       }
+       return 0;
+}
+
+/* enable an UART block if it isn't already */
+static inline void alchemy_uart_enable(u32 uart_phys)
+{
+       void __iomem *addr = (void __iomem *)KSEG1ADDR(uart_phys);
+
+       /* reset, enable clock, deassert reset */
+       if ((__raw_readl(addr + 0x100) & 3) != 3) {
+               __raw_writel(0, addr + 0x100);
+               wmb();
+               __raw_writel(1, addr + 0x100);
+               wmb();
+       }
+       __raw_writel(3, addr + 0x100);
+       wmb();
+}
+
+static inline void alchemy_uart_disable(u32 uart_phys)
+{
+       void __iomem *addr = (void __iomem *)KSEG1ADDR(uart_phys);
+       __raw_writel(0, addr + 0x100);  /* UART_MOD_CNTRL */
+       wmb();
+}
+
 static inline void alchemy_uart_putchar(u32 uart_phys, u8 c)
 {
        void __iomem *base = (void __iomem *)KSEG1ADDR(uart_phys);
@@ -634,6 +673,10 @@ enum soc_au1200_ints {
  */
 
 #define AU1000_IC0_PHYS_ADDR           0x10400000 /* 01234 */
+#define AU1000_UART0_PHYS_ADDR         0x11100000 /* 01234 */
+#define AU1000_UART1_PHYS_ADDR         0x11200000 /* 0234 */
+#define AU1000_UART2_PHYS_ADDR         0x11300000 /* 0 */
+#define AU1000_UART3_PHYS_ADDR         0x11400000 /* 0123 */
 #define AU1000_IC1_PHYS_ADDR           0x11800000 /* 01234 */
 #define AU1550_DBDMA_PHYS_ADDR         0x14002000 /* 34 */
 #define AU1550_DBDMA_CONF_PHYS_ADDR    0x14003000 /* 34 */
@@ -660,10 +703,6 @@ enum soc_au1200_ints {
 #define        MACDMA0_PHYS_ADDR       0x14004000
 #define        MACDMA1_PHYS_ADDR       0x14004200
 #define        I2S_PHYS_ADDR           0x11000000
-#define        UART0_PHYS_ADDR         0x11100000
-#define        UART1_PHYS_ADDR         0x11200000
-#define        UART2_PHYS_ADDR         0x11300000
-#define        UART3_PHYS_ADDR         0x11400000
 #define        SSI0_PHYS_ADDR          0x11600000
 #define        SSI1_PHYS_ADDR          0x11680000
 #define        SYS_PHYS_ADDR           0x11900000
@@ -695,8 +734,6 @@ enum soc_au1200_ints {
 #define        MACDMA0_PHYS_ADDR       0x14004000
 #define        MACDMA1_PHYS_ADDR       0x14004200
 #define        I2S_PHYS_ADDR           0x11000000
-#define        UART0_PHYS_ADDR         0x11100000
-#define        UART3_PHYS_ADDR         0x11400000
 #define GPIO2_PHYS_ADDR                0x11700000
 #define        SYS_PHYS_ADDR           0x11900000
 #define PCI_MEM_PHYS_ADDR      0x400000000ULL
@@ -732,9 +769,6 @@ enum soc_au1200_ints {
 #define        MACDMA0_PHYS_ADDR       0x14004000
 #define        MACDMA1_PHYS_ADDR       0x14004200
 #define        I2S_PHYS_ADDR           0x11000000
-#define        UART0_PHYS_ADDR         0x11100000
-#define        UART1_PHYS_ADDR         0x11200000
-#define        UART3_PHYS_ADDR         0x11400000
 #define        SSI0_PHYS_ADDR          0x11600000
 #define        SSI1_PHYS_ADDR          0x11680000
 #define GPIO2_PHYS_ADDR                0x11700000
@@ -758,9 +792,6 @@ enum soc_au1200_ints {
 #define        MACEN_PHYS_ADDR         0x10520000
 #define        MACDMA0_PHYS_ADDR       0x14004000
 #define        MACDMA1_PHYS_ADDR       0x14004200
-#define        UART0_PHYS_ADDR         0x11100000
-#define        UART1_PHYS_ADDR         0x11200000
-#define        UART3_PHYS_ADDR         0x11400000
 #define GPIO2_PHYS_ADDR                0x11700000
 #define        SYS_PHYS_ADDR           0x11900000
 #define PE_PHYS_ADDR           0x14008000
@@ -786,8 +817,6 @@ enum soc_au1200_ints {
 #define CIM_PHYS_ADDR          0x14004000
 #define USBM_PHYS_ADDR         0x14020000
 #define        USBH_PHYS_ADDR          0x14020100
-#define        UART0_PHYS_ADDR         0x11100000
-#define        UART1_PHYS_ADDR         0x11200000
 #define GPIO2_PHYS_ADDR                0x11700000
 #define        SYS_PHYS_ADDR           0x11900000
 #define PSC0_PHYS_ADDR         0x11A00000