#include <asm/hardware.h>
#include <asm/arch/mfp.h>
+#include <asm/arch/mfp-pxa3xx.h>
/* mfp_spin_lock is used to ensure that MFP register configuration
* (most likely a read-modify-write operation) is atomic, and that
static DEFINE_SPINLOCK(mfp_spin_lock);
static void __iomem *mfpr_mmio_base = (void __iomem *)&__REG(MFPR_BASE);
+
+struct pxa3xx_mfp_pin {
+ unsigned long config; /* -1 for not configured */
+ unsigned long mfpr_off; /* MFPRxx Register offset */
+ unsigned long mfpr_run; /* Run-Mode Register Value */
+ unsigned long mfpr_lpm; /* Low Power Mode Register Value */
+};
+
static struct pxa3xx_mfp_pin mfp_table[MFP_PIN_MAX];
+/* mapping of MFP_LPM_* definitions to MFPR_LPM_* register bits */
+const static unsigned long mfpr_lpm[] = {
+ MFPR_LPM_INPUT,
+ MFPR_LPM_DRIVE_LOW,
+ MFPR_LPM_DRIVE_HIGH,
+ MFPR_LPM_PULL_LOW,
+ MFPR_LPM_PULL_HIGH,
+ MFPR_LPM_FLOAT,
+};
+
+/* mapping of MFP_PULL_* definitions to MFPR_PULL_* register bits */
+const static unsigned long mfpr_pull[] = {
+ MFPR_PULL_NONE,
+ MFPR_PULL_LOW,
+ MFPR_PULL_HIGH,
+ MFPR_PULL_BOTH,
+};
+
+/* mapping of MFP_LPM_EDGE_* definitions to MFPR_EDGE_* register bits */
+const static unsigned long mfpr_edge[] = {
+ MFPR_EDGE_NONE,
+ MFPR_EDGE_RISE,
+ MFPR_EDGE_FALL,
+ MFPR_EDGE_BOTH,
+};
+
#define mfpr_readl(off) \
__raw_readl(mfpr_mmio_base + (off))
#define mfpr_writel(off, val) \
__raw_writel(val, mfpr_mmio_base + (off))
+#define mfp_configured(p) ((p)->config != -1)
+
/*
* perform a read-back of any MFPR register to make sure the
* previous writings are finished
*/
#define mfpr_sync() (void)__raw_readl(mfpr_mmio_base + 0)
-static inline void __mfp_config(int pin, unsigned long val)
+static inline void __mfp_config_run(struct pxa3xx_mfp_pin *p)
{
- unsigned long off = mfp_table[pin].mfpr_off;
+ if (mfp_configured(p))
+ mfpr_writel(p->mfpr_off, p->mfpr_run);
+}
- mfp_table[pin].mfpr_val = val;
- mfpr_writel(off, val);
+static inline void __mfp_config_lpm(struct pxa3xx_mfp_pin *p)
+{
+ if (mfp_configured(p) && p->mfpr_lpm != p->mfpr_run)
+ mfpr_writel(p->mfpr_off, p->mfpr_lpm);
}
-void pxa3xx_mfp_config(mfp_cfg_t *mfp_cfgs, int num)
+void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num)
{
- int i, pin;
- unsigned long val, flags;
- mfp_cfg_t *mfp_cfg = mfp_cfgs;
+ unsigned long flags;
+ int i;
spin_lock_irqsave(&mfp_spin_lock, flags);
- for (i = 0; i < num; i++, mfp_cfg++) {
- pin = MFP_CFG_PIN(*mfp_cfg);
- val = MFP_CFG_VAL(*mfp_cfg);
+ for (i = 0; i < num; i++, mfp_cfgs++) {
+ unsigned long tmp, c = *mfp_cfgs;
+ struct pxa3xx_mfp_pin *p;
+ int pin, af, drv, lpm, edge, pull;
+ pin = MFP_PIN(c);
BUG_ON(pin >= MFP_PIN_MAX);
-
- __mfp_config(pin, val);
+ p = &mfp_table[pin];
+
+ af = MFP_AF(c);
+ drv = MFP_DS(c);
+ lpm = MFP_LPM_STATE(c);
+ edge = MFP_LPM_EDGE(c);
+ pull = MFP_PULL(c);
+
+ /* run-mode pull settings will conflict with MFPR bits of
+ * low power mode state, calculate mfpr_run and mfpr_lpm
+ * individually if pull != MFP_PULL_NONE
+ */
+ tmp = MFPR_AF_SEL(af) | MFPR_DRIVE(drv);
+
+ if (likely(pull == MFP_PULL_NONE)) {
+ p->mfpr_run = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
+ p->mfpr_lpm = p->mfpr_run;
+ } else {
+ p->mfpr_lpm = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
+ p->mfpr_run = tmp | mfpr_pull[pull];
+ }
+
+ p->config = c; __mfp_config_run(p);
}
mfpr_sync();
do {
mfp_table[i].mfpr_off = offset;
- mfp_table[i].mfpr_val = 0;
+ mfp_table[i].mfpr_run = 0;
+ mfp_table[i].mfpr_lpm = 0;
offset += 4; i++;
} while ((i <= p->end) && (p->end != -1));
}
void __init pxa3xx_init_mfp(void)
{
- memset(mfp_table, 0, sizeof(mfp_table));
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(mfp_table); i++)
+ mfp_table[i].config = -1;
}
#ifndef __ASM_ARCH_MFP_PXA3XX_H
#define __ASM_ARCH_MFP_PXA3XX_H
+#define MFPR_BASE (0x40e10000)
+#define MFPR_SIZE (PAGE_SIZE)
+
+/* MFPR register bit definitions */
+#define MFPR_PULL_SEL (0x1 << 15)
+#define MFPR_PULLUP_EN (0x1 << 14)
+#define MFPR_PULLDOWN_EN (0x1 << 13)
+#define MFPR_SLEEP_SEL (0x1 << 9)
+#define MFPR_SLEEP_OE_N (0x1 << 7)
+#define MFPR_EDGE_CLEAR (0x1 << 6)
+#define MFPR_EDGE_FALL_EN (0x1 << 5)
+#define MFPR_EDGE_RISE_EN (0x1 << 4)
+
+#define MFPR_SLEEP_DATA(x) ((x) << 8)
+#define MFPR_DRIVE(x) (((x) & 0x7) << 10)
+#define MFPR_AF_SEL(x) (((x) & 0x7) << 0)
+
+#define MFPR_EDGE_NONE (0)
+#define MFPR_EDGE_RISE (MFPR_EDGE_RISE_EN)
+#define MFPR_EDGE_FALL (MFPR_EDGE_FALL_EN)
+#define MFPR_EDGE_BOTH (MFPR_EDGE_RISE | MFPR_EDGE_FALL)
+
+/*
+ * Table that determines the low power modes outputs, with actual settings
+ * used in parentheses for don't-care values. Except for the float output,
+ * the configured driven and pulled levels match, so if there is a need for
+ * non-LPM pulled output, the same configuration could probably be used.
+ *
+ * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel
+ * (bit 7) (bit 8) (bit 14) (bit 13) (bit 15)
+ *
+ * Input 0 X(0) X(0) X(0) 0
+ * Drive 0 0 0 0 X(1) 0
+ * Drive 1 0 1 X(1) 0 0
+ * Pull hi (1) 1 X(1) 1 0 0
+ * Pull lo (0) 1 X(0) 0 1 0
+ * Z (float) 1 X(0) 0 0 0
+ */
+#define MFPR_LPM_INPUT (0)
+#define MFPR_LPM_DRIVE_LOW (MFPR_SLEEP_DATA(0) | MFPR_PULLDOWN_EN)
+#define MFPR_LPM_DRIVE_HIGH (MFPR_SLEEP_DATA(1) | MFPR_PULLUP_EN)
+#define MFPR_LPM_PULL_LOW (MFPR_LPM_DRIVE_LOW | MFPR_SLEEP_OE_N)
+#define MFPR_LPM_PULL_HIGH (MFPR_LPM_DRIVE_HIGH | MFPR_SLEEP_OE_N)
+#define MFPR_LPM_FLOAT (MFPR_SLEEP_OE_N)
+#define MFPR_LPM_MASK (0xe080)
+
+/*
+ * The pullup and pulldown state of the MFP pin at run mode is by default
+ * determined by the selected alternate function. In case that some buggy
+ * devices need to override this default behavior, the definitions below
+ * indicates the setting of corresponding MFPR bits
+ *
+ * Definition pull_sel pullup_en pulldown_en
+ * MFPR_PULL_NONE 0 0 0
+ * MFPR_PULL_LOW 1 0 1
+ * MFPR_PULL_HIGH 1 1 0
+ * MFPR_PULL_BOTH 1 1 1
+ */
+#define MFPR_PULL_NONE (0)
+#define MFPR_PULL_LOW (MFPR_PULL_SEL | MFPR_PULLDOWN_EN)
+#define MFPR_PULL_BOTH (MFPR_PULL_LOW | MFPR_PULLUP_EN)
+#define MFPR_PULL_HIGH (MFPR_PULL_SEL | MFPR_PULLUP_EN)
+
/* PXA3xx common MFP configurations - processor specific ones defined
* in mfp-pxa300.h and mfp-pxa320.h
*/
#define GPIO5_2_GPIO MFP_CFG(GPIO5_2, AF0)
#define GPIO6_2_GPIO MFP_CFG(GPIO6_2, AF0)
+/*
+ * each MFP pin will have a MFPR register, since the offset of the
+ * register varies between processors, the processor specific code
+ * should initialize the pin offsets by pxa3xx_mfp_init_addr()
+ *
+ * pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map"
+ * structure, which represents a range of MFP pins from "start" to
+ * "end", with the offset begining at "offset", to define a single
+ * pin, let "end" = -1
+ *
+ * use
+ *
+ * MFP_ADDR_X() to define a range of pins
+ * MFP_ADDR() to define a single pin
+ * MFP_ADDR_END to signal the end of pin offset definitions
+ */
+struct pxa3xx_mfp_addr_map {
+ unsigned int start;
+ unsigned int end;
+ unsigned long offset;
+};
+
+#define MFP_ADDR_X(start, end, offset) \
+ { MFP_PIN_##start, MFP_PIN_##end, offset }
+
+#define MFP_ADDR(pin, offset) \
+ { MFP_PIN_##pin, -1, offset }
+
+#define MFP_ADDR_END { MFP_PIN_INVALID, 0 }
+
+/*
+ * pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access
+ * to the MFPR register
+ */
+unsigned long pxa3xx_mfp_read(int mfp);
+void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val);
+
+/*
+ * pxa3xx_mfp_config - configure the MFPR registers
+ *
+ * used by board specific initialization code
+ */
+void pxa3xx_mfp_config(unsigned long *mfp_cfgs, int num);
+
+/*
+ * pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin
+ * index and MFPR register offset
+ *
+ * used by processor specific code
+ */
+void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *);
+void __init pxa3xx_init_mfp(void);
#endif /* __ASM_ARCH_MFP_PXA3XX_H */
#ifndef __ASM_ARCH_MFP_H
#define __ASM_ARCH_MFP_H
-#define MFPR_BASE (0x40e10000)
-#define MFPR_SIZE (PAGE_SIZE)
-
#define mfp_to_gpio(m) ((m) % 128)
/* list of all the configurable MFP pins */
MFP_PIN_MAX,
};
-/*
- * Table that determines the low power modes outputs, with actual settings
- * used in parentheses for don't-care values. Except for the float output,
- * the configured driven and pulled levels match, so if there is a need for
- * non-LPM pulled output, the same configuration could probably be used.
- *
- * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel
- * (bit 7) (bit 8) (bit 14d) (bit 13d)
- *
- * Drive 0 0 0 0 X (1) 0
- * Drive 1 0 1 X (1) 0 0
- * Pull hi (1) 1 X(1) 1 0 0
- * Pull lo (0) 1 X(0) 0 1 0
- * Z (float) 1 X(0) 0 0 0
- */
-#define MFP_LPM_DRIVE_LOW 0x8
-#define MFP_LPM_DRIVE_HIGH 0x6
-#define MFP_LPM_PULL_HIGH 0x7
-#define MFP_LPM_PULL_LOW 0x9
-#define MFP_LPM_FLOAT 0x1
-#define MFP_LPM_PULL_NEITHER 0x0
-
-/*
- * The pullup and pulldown state of the MFP pin is by default determined by
- * selected alternate function. In case some buggy devices need to override
- * this default behavior, pxa3xx_mfp_set_pull() can be invoked with one of
- * the following definition as the parameter.
- *
- * Definition pull_sel pullup_en pulldown_en
- * MFP_PULL_HIGH 1 1 0
- * MFP_PULL_LOW 1 0 1
- * MFP_PULL_BOTH 1 1 1
- * MFP_PULL_NONE 1 0 0
- * MFP_PULL_DEFAULT 0 X X
- *
- * NOTE: pxa3xx_mfp_set_pull() will modify the PULLUP_EN and PULLDOWN_EN
- * bits, which will cause potential conflicts with the low power mode
- * setting, device drivers should take care of this
- */
-#define MFP_PULL_BOTH (0x7u)
-#define MFP_PULL_HIGH (0x6u)
-#define MFP_PULL_LOW (0x5u)
-#define MFP_PULL_NONE (0x4u)
-#define MFP_PULL_DEFAULT (0x0u)
-
-#define MFP_AF0 (0)
-#define MFP_AF1 (1)
-#define MFP_AF2 (2)
-#define MFP_AF3 (3)
-#define MFP_AF4 (4)
-#define MFP_AF5 (5)
-#define MFP_AF6 (6)
-#define MFP_AF7 (7)
-
-#define MFP_DS01X (0)
-#define MFP_DS02X (1)
-#define MFP_DS03X (2)
-#define MFP_DS04X (3)
-#define MFP_DS06X (4)
-#define MFP_DS08X (5)
-#define MFP_DS10X (6)
-#define MFP_DS12X (7)
-
-#define MFP_EDGE_BOTH 0x3
-#define MFP_EDGE_RISE 0x2
-#define MFP_EDGE_FALL 0x1
-#define MFP_EDGE_NONE 0x0
-
-#define MFPR_AF_MASK 0x0007
-#define MFPR_DRV_MASK 0x1c00
-#define MFPR_RDH_MASK 0x0200
-#define MFPR_LPM_MASK 0xe180
-#define MFPR_PULL_MASK 0xe000
-#define MFPR_EDGE_MASK 0x0070
-
-#define MFPR_ALT_OFFSET 0
-#define MFPR_ERE_OFFSET 4
-#define MFPR_EFE_OFFSET 5
-#define MFPR_EC_OFFSET 6
-#define MFPR_SON_OFFSET 7
-#define MFPR_SD_OFFSET 8
-#define MFPR_SS_OFFSET 9
-#define MFPR_DRV_OFFSET 10
-#define MFPR_PD_OFFSET 13
-#define MFPR_PU_OFFSET 14
-#define MFPR_PS_OFFSET 15
-
-#define MFPR(af, drv, rdh, lpm, edge) \
- (((af) & 0x7) | (((drv) & 0x7) << 10) |\
- (((rdh) & 0x1) << 9) |\
- (((lpm) & 0x3) << 7) |\
- (((lpm) & 0x4) << 12)|\
- (((lpm) & 0x8) << 10)|\
- ((!(edge)) << 6) |\
- (((edge) & 0x1) << 5) |\
- (((edge) & 0x2) << 3))
-
/*
* a possible MFP configuration is represented by a 32-bit integer
- * bit 0..15 - MFPR value (16-bit)
- * bit 16..31 - mfp pin index (used to obtain the MFPR offset)
+ *
+ * bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
+ * bit 10..12 - Alternate Function Selection
+ * bit 13..15 - Drive Strength
+ * bit 16..18 - Low Power Mode State
+ * bit 19..20 - Low Power Mode Edge Detection
+ * bit 21..22 - Run Mode Pull State
*
* to facilitate the definition, the following macros are provided
*
- * MFPR_DEFAULT - default MFPR value, with
+ * MFP_CFG_DEFAULT - default MFP configuration value, with
* alternate function = 0,
- * drive strength = fast 1mA (MFP_DS01X)
+ * drive strength = fast 3mA (MFP_DS03X)
* low power mode = default
- * release dalay hold = false (RDH bit)
* edge detection = none
*
* MFP_CFG - default MFPR value with alternate function
* low power mode
* MFP_CFG_X - default MFPR value with alternate function,
* pin drive strength and low power mode
- *
- * use
- *
- * MFP_CFG_PIN - to get the MFP pin index
- * MFP_CFG_VAL - to get the corresponding MFPR value
*/
-typedef uint32_t mfp_cfg_t;
-
-#define MFP_CFG_PIN(mfp_cfg) (((mfp_cfg) >> 16) & 0xffff)
-#define MFP_CFG_VAL(mfp_cfg) ((mfp_cfg) & 0xffff)
-
-/*
- * MFP register defaults to
- * drive strength fast 3mA (010'b)
- * edge detection logic disabled
- * alternate function 0
- */
-#define MFPR_DEFAULT (0x0840)
+typedef unsigned long mfp_cfg_t;
+
+#define MFP_PIN(x) ((x) & 0x3ff)
+
+#define MFP_AF0 (0x0 << 10)
+#define MFP_AF1 (0x1 << 10)
+#define MFP_AF2 (0x2 << 10)
+#define MFP_AF3 (0x3 << 10)
+#define MFP_AF4 (0x4 << 10)
+#define MFP_AF5 (0x5 << 10)
+#define MFP_AF6 (0x6 << 10)
+#define MFP_AF7 (0x7 << 10)
+#define MFP_AF_MASK (0x7 << 10)
+#define MFP_AF(x) (((x) >> 10) & 0x7)
+
+#define MFP_DS01X (0x0 << 13)
+#define MFP_DS02X (0x1 << 13)
+#define MFP_DS03X (0x2 << 13)
+#define MFP_DS04X (0x3 << 13)
+#define MFP_DS06X (0x4 << 13)
+#define MFP_DS08X (0x5 << 13)
+#define MFP_DS10X (0x6 << 13)
+#define MFP_DS13X (0x7 << 13)
+#define MFP_DS_MASK (0x7 << 13)
+#define MFP_DS(x) (((x) >> 13) & 0x7)
+
+#define MFP_LPM_INPUT (0x0 << 16)
+#define MFP_LPM_DRIVE_LOW (0x1 << 16)
+#define MFP_LPM_DRIVE_HIGH (0x2 << 16)
+#define MFP_LPM_PULL_LOW (0x3 << 16)
+#define MFP_LPM_PULL_HIGH (0x4 << 16)
+#define MFP_LPM_FLOAT (0x5 << 16)
+#define MFP_LPM_STATE_MASK (0x7 << 16)
+#define MFP_LPM_STATE(x) (((x) >> 16) & 0x7)
+
+#define MFP_LPM_EDGE_NONE (0x0 << 19)
+#define MFP_LPM_EDGE_RISE (0x1 << 19)
+#define MFP_LPM_EDGE_FALL (0x2 << 19)
+#define MFP_LPM_EDGE_BOTH (0x3 << 19)
+#define MFP_LPM_EDGE_MASK (0x3 << 19)
+#define MFP_LPM_EDGE(x) (((x) >> 19) & 0x3)
+
+#define MFP_PULL_NONE (0x0 << 21)
+#define MFP_PULL_LOW (0x1 << 21)
+#define MFP_PULL_HIGH (0x2 << 21)
+#define MFP_PULL_BOTH (0x3 << 21)
+#define MFP_PULL_MASK (0x3 << 21)
+#define MFP_PULL(x) (((x) >> 21) & 0x3)
+
+#define MFP_CFG_DEFAULT (MFP_AF0 | MFP_DS03X | MFP_LPM_INPUT |\
+ MFP_LPM_EDGE_NONE | MFP_PULL_NONE)
#define MFP_CFG(pin, af) \
- ((MFP_PIN_##pin << 16) | MFPR_DEFAULT | (MFP_##af))
+ ((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af))
#define MFP_CFG_DRV(pin, af, drv) \
- ((MFP_PIN_##pin << 16) | (MFPR_DEFAULT & ~MFPR_DRV_MASK) |\
- ((MFP_##drv) << 10) | (MFP_##af))
+ ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv))
#define MFP_CFG_LPM(pin, af, lpm) \
- ((MFP_PIN_##pin << 16) | (MFPR_DEFAULT & ~MFPR_LPM_MASK) |\
- (((MFP_LPM_##lpm) & 0x3) << 7) |\
- (((MFP_LPM_##lpm) & 0x4) << 12) |\
- (((MFP_LPM_##lpm) & 0x8) << 10) |\
- (MFP_##af))
+ ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm))
#define MFP_CFG_X(pin, af, drv, lpm) \
- ((MFP_PIN_##pin << 16) |\
- (MFPR_DEFAULT & ~(MFPR_DRV_MASK | MFPR_LPM_MASK)) |\
- ((MFP_##drv) << 10) | (MFP_##af) |\
- (((MFP_LPM_##lpm) & 0x3) << 7) |\
- (((MFP_LPM_##lpm) & 0x4) << 12) |\
- (((MFP_LPM_##lpm) & 0x8) << 10))
-
-/*
- * each MFP pin will have a MFPR register, since the offset of the
- * register varies between processors, the processor specific code
- * should initialize the pin offsets by pxa3xx_mfp_init_addr()
- *
- * pxa3xx_mfp_init_addr - accepts a table of "pxa3xx_mfp_addr_map"
- * structure, which represents a range of MFP pins from "start" to
- * "end", with the offset begining at "offset", to define a single
- * pin, let "end" = -1
- *
- * use
- *
- * MFP_ADDR_X() to define a range of pins
- * MFP_ADDR() to define a single pin
- * MFP_ADDR_END to signal the end of pin offset definitions
- */
-struct pxa3xx_mfp_addr_map {
- unsigned int start;
- unsigned int end;
- unsigned long offset;
-};
-
-#define MFP_ADDR_X(start, end, offset) \
- { MFP_PIN_##start, MFP_PIN_##end, offset }
-
-#define MFP_ADDR(pin, offset) \
- { MFP_PIN_##pin, -1, offset }
-
-#define MFP_ADDR_END { MFP_PIN_INVALID, 0 }
-
-struct pxa3xx_mfp_pin {
- unsigned long mfpr_off; /* MFPRxx register offset */
- unsigned long mfpr_val; /* MFPRxx register value */
-};
-
-/*
- * pxa3xx_mfp_read()/pxa3xx_mfp_write() - for direct read/write access
- * to the MFPR register
- */
-unsigned long pxa3xx_mfp_read(int mfp);
-void pxa3xx_mfp_write(int mfp, unsigned long mfpr_val);
-
-/*
- * pxa3xx_mfp_config - configure the MFPR registers
- *
- * used by board specific initialization code
- */
-void pxa3xx_mfp_config(mfp_cfg_t *mfp_cfgs, int num);
-
-/*
- * pxa3xx_mfp_init_addr() - initialize the mapping between mfp pin
- * index and MFPR register offset
- *
- * used by processor specific code
- */
-void __init pxa3xx_mfp_init_addr(struct pxa3xx_mfp_addr_map *);
-void __init pxa3xx_init_mfp(void);
+ ((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\
+ (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm))
#endif /* __ASM_ARCH_MFP_H */
git.openpandora.org / pandora-kernel.git / commitdiff