pch_uart: reference clock on CM-iTC

Default clock source for UARTs on Topcliff is external UART_CLK.
On CM-iTC USB_48MHz is used instead. After VCO2PLL and DIV
manipulations UARTs will receive 192 MHz.
Clock manipulations on Topcliff are controlled in pch_phub.c

v2: redone against the linux-next tree
v3: redone against linux/kernel/git/next/linux-next.git snapshot

Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

diff --git a/drivers/misc/pch_phub.c b/drivers/misc/pch_phub.c
index 98bffc4..5dd0b92 100644 (file)
--- a/drivers/misc/pch_phub.c
+++ b/drivers/misc/pch_phub.c
@@ -27,6 +27,7 @@
 #include <linux/mutex.h>
 #include <linux/if_ether.h>
 #include <linux/ctype.h>
+#include <linux/dmi.h>
 
 #define PHUB_STATUS 0x00               /* Status Register offset */
 #define PHUB_CONTROL 0x04              /* Control Register offset */
@@ -46,6 +47,13 @@
 #define PCH_MINOR_NOS 1
 #define CLKCFG_CAN_50MHZ 0x12000000
 #define CLKCFG_CANCLK_MASK 0xFF000000
+#define CLKCFG_UART_MASK                       0xFFFFFF
+
+/* CM-iTC */
+#define CLKCFG_UART_48MHZ                      (1 << 16)
+#define CLKCFG_BAUDDIV                         (2 << 20)
+#define CLKCFG_PLL2VCO                         (8 << 9)
+#define CLKCFG_UARTCLKSEL                      (1 << 18)
 
 /* Macros for ML7213 */
 #define PCI_VENDOR_ID_ROHM                     0x10db
@@ -618,6 +626,14 @@ static int __devinit pch_phub_probe(struct pci_dev *pdev,
                                               CLKCFG_CAN_50MHZ,
                                               CLKCFG_CANCLK_MASK);
 
+               /* quirk for CM-iTC board */
+               if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+                       pch_phub_read_modify_write_reg(chip,
+                                               (unsigned int)CLKCFG_REG_OFFSET,
+                                               CLKCFG_UART_48MHZ | CLKCFG_BAUDDIV |
+                                               CLKCFG_PLL2VCO | CLKCFG_UARTCLKSEL,
+                                               CLKCFG_UART_MASK);
+
                /* set the prefech value */
                iowrite32(0x000affaa, chip->pch_phub_base_address + 0x14);
                /* set the interrupt delay value */

diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c
index a5ce9a5..a9ad7f3 100644 (file)
--- a/drivers/tty/serial/pch_uart.c
+++ b/drivers/tty/serial/pch_uart.c
@@ -21,6 +21,7 @@
 #include <linux/serial_core.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
+#include <linux/dmi.h>
 
 #include <linux/dmaengine.h>
 #include <linux/pch_dma.h>
@@ -1404,14 +1405,18 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
        if (!rxbuf)
                goto init_port_free_txbuf;
 
+       base_baud = 1843200; /* 1.8432MHz */
+
+       /* quirk for CM-iTC board */
+       if (strstr(dmi_get_system_info(DMI_BOARD_NAME), "CM-iTC"))
+               base_baud = 192000000; /* 192.0MHz */
+
        switch (port_type) {
        case PORT_UNKNOWN:
                fifosize = 256; /* EG20T/ML7213: UART0 */
-               base_baud = 1843200; /* 1.8432MHz */
                break;
        case PORT_8250:
                fifosize = 64; /* EG20T:UART1~3  ML7213: UART1~2*/
-               base_baud = 1843200; /* 1.8432MHz */
                break;
        default:
                dev_err(&pdev->dev, "Invalid Port Type(=%d)\n", port_type);