x86: undo visws/numaq build changes

arch/x86/pci/Makefile_32 has a nasty detail. VISWS and NUMAQ build
override the generic pci-y rules. This needs a proper cleanup, but
that needs more thoughts. Undo

commit 895d30935ebe05f192e844792668bf8d19deaae7
    x86: numaq fix
    do not override the existing pci-y rule when adding visws or
    numaq rules.

There is also a stupid init function ordering problem vs. acpi.o

Add comments to the Makefile to avoid tripping over this again.

Remove the srat stub code in discontig_32.c to allow a proper NUMAQ
build.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

diff --git a/arch/x86/mm/discontig_32.c b/arch/x86/mm/discontig_32.c
index 1837885..914ccf9 100644 (file)
--- a/arch/x86/mm/discontig_32.c
+++ b/arch/x86/mm/discontig_32.c
@@ -476,29 +476,3 @@ int memory_add_physaddr_to_nid(u64 addr)
 
 EXPORT_SYMBOL_GPL(memory_add_physaddr_to_nid);
 #endif
-
-#ifndef CONFIG_HAVE_ARCH_PARSE_SRAT
-/*
- * XXX FIXME: Make SLIT table parsing available to 32-bit NUMA
- *
- * These stub functions are needed to compile 32-bit NUMA when SRAT is
- * not set. There are functions in srat_64.c for parsing this table
- * and it may be possible to make them common functions.
- */
-void acpi_numa_slit_init (struct acpi_table_slit *slit)
-{
-       printk(KERN_INFO "ACPI: No support for parsing SLIT table\n");
-}
-
-void acpi_numa_processor_affinity_init (struct acpi_srat_cpu_affinity *pa)
-{
-}
-
-void acpi_numa_memory_affinity_init (struct acpi_srat_mem_affinity *ma)
-{
-}
-
-void acpi_numa_arch_fixup(void)
-{
-}
-#endif /* CONFIG_HAVE_ARCH_PARSE_SRAT */

diff --git a/arch/x86/pci/Makefile_32 b/arch/x86/pci/Makefile_32
index 7fa5198..89ec35d 100644 (file)
--- a/arch/x86/pci/Makefile_32
+++ b/arch/x86/pci/Makefile_32
@@ -6,11 +6,19 @@ obj-$(CONFIG_PCI_DIRECT)      += direct.o
 obj-$(CONFIG_PCI_OLPC)         += olpc.o
 
 pci-y                          := fixup.o
+
+# Do not change the ordering here. There is a nasty init function
+# ordering dependency which breaks when you move acpi.o below
+# legacy/irq.o
 pci-$(CONFIG_ACPI)             += acpi.o
 pci-y                          += legacy.o irq.o
 
-pci-$(CONFIG_X86_VISWS)                += visws.o fixup.o
-pci-$(CONFIG_X86_NUMAQ)                += numa.o irq.o
+# Careful: VISWS and NUMAQ overrule the pci-y above. The colons are
+# therefor correct. This needs a proper fix by distangling the code.
+pci-$(CONFIG_X86_VISWS)                := visws.o fixup.o
+pci-$(CONFIG_X86_NUMAQ)                := numa.o irq.o
+
+# Necessary for NUMAQ as well
 pci-$(CONFIG_NUMA)             += mp_bus_to_node.o
 
 obj-y                          += $(pci-y) common.o early.o