smsc9420: replace printk with netdev_ calls

Signed-off-by: Ben Boeckel <mathstuf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/ethernet/smsc/smsc9420.c b/drivers/net/ethernet/smsc/smsc9420.c
index e55e336..059bcaf 100644 (file)
--- a/drivers/net/ethernet/smsc/smsc9420.c
+++ b/drivers/net/ethernet/smsc/smsc9420.c
@@ -99,17 +99,17 @@ MODULE_PARM_DESC(debug, "debug level");
 
 #define smsc_dbg(TYPE, f, a...) \
 do {   if ((pd)->msg_enable & NETIF_MSG_##TYPE) \
-               printk(KERN_DEBUG PFX f "\n", ## a); \
+               netdev_dbg((pd)->dev, PFX f "\n", ## a); \
 } while (0)
 
 #define smsc_info(TYPE, f, a...) \
 do {   if ((pd)->msg_enable & NETIF_MSG_##TYPE) \
-               printk(KERN_INFO PFX f "\n", ## a); \
+               netdev_info((pd)->dev, PFX f "\n", ## a); \
 } while (0)
 
 #define smsc_warn(TYPE, f, a...) \
 do {   if ((pd)->msg_enable & NETIF_MSG_##TYPE) \
-               printk(KERN_WARNING PFX f "\n", ## a); \
+               netdev_warn((pd)->dev, PFX f "\n", ## a); \
 } while (0)
 
 static inline u32 smsc9420_reg_read(struct smsc9420_pdata *pd, u32 offset)
@@ -1168,7 +1168,7 @@ static int smsc9420_mii_probe(struct net_device *dev)
 
        /* Device only supports internal PHY at address 1 */
        if (!pd->mii_bus->phy_map[1]) {
-               pr_err("%s: no PHY found at address 1\n", dev->name);
+               netdev_err(dev, "no PHY found at address 1\n");
                return -ENODEV;
        }
 
@@ -1180,12 +1180,12 @@ static int smsc9420_mii_probe(struct net_device *dev)
                             smsc9420_phy_adjust_link, PHY_INTERFACE_MODE_MII);
 
        if (IS_ERR(phydev)) {
-               pr_err("%s: Could not attach to PHY\n", dev->name);
+               netdev_err(dev, "Could not attach to PHY\n");
                return PTR_ERR(phydev);
        }
 
-       pr_info("%s: attached PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n",
-               dev->name, phydev->drv->name, dev_name(&phydev->dev), phydev->irq);
+       netdev_info(dev, "attached PHY driver [%s] (mii_bus:phy_addr=%s, irq=%d)\n",
+                   phydev->drv->name, dev_name(&phydev->dev), phydev->irq);
 
        /* mask with MAC supported features */
        phydev->supported &= (PHY_BASIC_FEATURES | SUPPORTED_Pause |
@@ -1582,12 +1582,12 @@ smsc9420_probe(struct pci_dev *pdev, const struct pci_device_id *id)
        int result = 0;
        u32 id_rev;
 
-       printk(KERN_INFO DRV_DESCRIPTION " version " DRV_VERSION "\n");
+       pr_info(DRV_DESCRIPTION " version " DRV_VERSION "\n");
 
        /* First do the PCI initialisation */
        result = pci_enable_device(pdev);
        if (unlikely(result)) {
-               printk(KERN_ERR "Cannot enable smsc9420\n");
+               pr_err("Cannot enable smsc9420\n");
                goto out_0;
        }
 
@@ -1600,24 +1600,24 @@ smsc9420_probe(struct pci_dev *pdev, const struct pci_device_id *id)
        SET_NETDEV_DEV(dev, &pdev->dev);
 
        if (!(pci_resource_flags(pdev, SMSC_BAR) & IORESOURCE_MEM)) {
-               printk(KERN_ERR "Cannot find PCI device base address\n");
+               netdev_err(dev, "Cannot find PCI device base address\n");
                goto out_free_netdev_2;
        }
 
        if ((pci_request_regions(pdev, DRV_NAME))) {
-               printk(KERN_ERR "Cannot obtain PCI resources, aborting.\n");
+               netdev_err(dev, "Cannot obtain PCI resources, aborting.\n");
                goto out_free_netdev_2;
        }
 
        if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
-               printk(KERN_ERR "No usable DMA configuration, aborting.\n");
+               netdev_err(dev, "No usable DMA configuration, aborting.\n");
                goto out_free_regions_3;
        }
 
        virt_addr = ioremap(pci_resource_start(pdev, SMSC_BAR),
                pci_resource_len(pdev, SMSC_BAR));
        if (!virt_addr) {
-               printk(KERN_ERR "Cannot map device registers, aborting.\n");
+               netdev_err(dev, "Cannot map device registers, aborting.\n");
                goto out_free_regions_3;
        }