}
EXPORT_SYMBOL(dibusb_read_eeprom_byte);
-static struct mt2060_config stk3000p_mt2060_config = {
- .i2c_address = 0x60,
-};
-
-static int dibusb_tuner_init(struct dvb_frontend *fe)
-{
- struct dvb_usb_device *d = fe->dvb->priv;
- struct dibusb_state *st = d->priv;
-
- if (d->tuner_pass_ctrl && st->mt2060_present) {
- int ret;
- d->tuner_pass_ctrl(d->fe, 1, stk3000p_mt2060_config.i2c_address);
- ret = mt2060_init(&st->mt2060);
- d->tuner_pass_ctrl(d->fe, 0, 0);
- return ret;
- }
- return dvb_usb_pll_init_i2c(fe);
-}
-
-static int dibusb_tuner_set(struct dvb_frontend *fe, struct dvb_frontend_parameters *fep)
-{
- struct dvb_usb_device *d = fe->dvb->priv;
- struct dibusb_state *st = d->priv;
-
- if (d->tuner_pass_ctrl && st->mt2060_present) {
- int ret;
- d->tuner_pass_ctrl(d->fe, 1, stk3000p_mt2060_config.i2c_address);
- ret = mt2060_set(&st->mt2060,fep);
- d->tuner_pass_ctrl(d->fe,0,0);
- return ret;
- }
- return dvb_usb_pll_set_i2c(fe,fep);
-}
-
static const struct dib3000p_agc_config dib3000p_agc_panasonic_env57h1xd5 = {
{ 0x51, 0x301d, 0x0, 0x1cc7, 0xdc29, 0x570a,
0xbae1, 0x8ccd, 0x3b6d, 0x551d, 0xa, 0x951e }
0xa8f6, 0x5eb8, 0x65ff, 0x40ff, 0x8a, 0x1114 }
};
+static struct mt2060_config stk3000p_mt2060_config = {
+ .i2c_address = 0x60,
+};
+
int dibusb_dib3000mc_frontend_attach(struct dvb_usb_device *d)
{
struct dib3000_config demod_cfg;
struct dibusb_state *st = d->priv;
-
- demod_cfg.agc = &dib3000p_agc_panasonic_env57h1xd5;
- demod_cfg.pll_set = dibusb_tuner_set;
- demod_cfg.pll_init = dibusb_tuner_init;
-
- for (demod_cfg.demod_address = 0x8; demod_cfg.demod_address < 0xd; demod_cfg.demod_address++)
- if ((d->fe = dib3000mc_attach(&demod_cfg,&d->i2c_adap,&st->ops)) != NULL) {
- d->tuner_pass_ctrl = st->ops.tuner_pass_ctrl;
- return 0;
- }
-
return -ENODEV;
}
EXPORT_SYMBOL(dibusb_dib3000mc_frontend_attach);
int dibusb_dib3000mc_tuner_attach (struct dvb_usb_device *d)
{
- int ret;
- u8 a,b;
- u16 if1 = 1220;
-
- if (d->tuner_pass_ctrl) {
- struct dibusb_state *st = d->priv;
- d->tuner_pass_ctrl(d->fe, 1, stk3000p_mt2060_config.i2c_address);
- // First IF calibration for Liteon Sticks
- if (d->udev->descriptor.idVendor == USB_VID_LITEON &&
- d->udev->descriptor.idProduct == USB_PID_LITEON_DVB_T_WARM) {
-
- dibusb_read_eeprom_byte(d,0x7E,&a);
- dibusb_read_eeprom_byte(d,0x7F,&b);
-
- if (a == 0xFF && b == 0xFF)
- if1 = 1220;
- else if (a == 0x00)
- if1 = 1220+b;
- else if (a == 0x80)
- if1 = 1220-b;
- else {
- warn("LITE-ON DVB-T Tuner : Strange IF1 calibration :%2X %2X\n",(int)a,(int)b);
- if1 = 1220;
- }
- }
- if ((ret = mt2060_attach(&st->mt2060,&stk3000p_mt2060_config, &d->i2c_adap,if1)) != 0) {
- /* not found - use panasonic pll parameters */
- d->pll_addr = 0x60;
- d->pll_desc = &dvb_pll_env57h1xd5;
- } else {
- st->mt2060_present = 1;
- /* set the correct agc parameters for the dib3000p */
- dib3000mc_set_agc_config(d->fe, &dib3000p_agc_microtune_mt2060);
- }
- d->tuner_pass_ctrl(d->fe,0,0);
- }
- return 0;
+ return -ENODEV;
}
EXPORT_SYMBOL(dibusb_dib3000mc_tuner_attach);
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.=
*/
-/* See mt2060_priv.h for details */
-
/* In that file, frequencies are expressed in kiloHertz to avoid 32 bits overflows */
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/delay.h>
#include <linux/dvb/frontend.h>
+#include <linux/i2c.h>
+
+#include "dvb_frontend.h"
+
#include "mt2060.h"
#include "mt2060_priv.h"
module_param(debug, int, 0644);
MODULE_PARM_DESC(debug, "Turn on/off debugging (default:off).");
-#define dprintk(args...) do { if (debug) { printk(KERN_DEBUG "MT2060: " args); printk("\n"); } } while (0)
+#define dprintk(args...) do { if (debug) {printk(KERN_DEBUG "MT2060: " args); printk("\n"); }} while (0)
// Reads a single register
-static int mt2060_readreg(struct mt2060_state *state, u8 reg, u8 *val)
+static int mt2060_readreg(struct mt2060_priv *priv, u8 reg, u8 *val)
{
struct i2c_msg msg[2] = {
- { .addr = state->config->i2c_address, .flags = 0, .buf = ®, .len = 1 },
- { .addr = state->config->i2c_address, .flags = I2C_M_RD, .buf = val, .len = 1 },
+ { .addr = priv->cfg->i2c_address, .flags = 0, .buf = ®, .len = 1 },
+ { .addr = priv->cfg->i2c_address, .flags = I2C_M_RD, .buf = val, .len = 1 },
};
- if (i2c_transfer(state->i2c, msg, 2) != 2) {
+ if (i2c_transfer(priv->i2c, msg, 2) != 2) {
printk(KERN_WARNING "mt2060 I2C read failed\n");
return -EREMOTEIO;
}
}
// Writes a single register
-static int mt2060_writereg(struct mt2060_state *state, u8 reg, u8 val)
+static int mt2060_writereg(struct mt2060_priv *priv, u8 reg, u8 val)
{
- u8 buf[2];
+ u8 buf[2] = { reg, val };
struct i2c_msg msg = {
- .addr = state->config->i2c_address, .flags = 0, .buf = buf, .len = 2
+ .addr = priv->cfg->i2c_address, .flags = 0, .buf = buf, .len = 2
};
- buf[0]=reg;
- buf[1]=val;
- if (i2c_transfer(state->i2c, &msg, 1) != 1) {
+ if (i2c_transfer(priv->i2c, &msg, 1) != 1) {
printk(KERN_WARNING "mt2060 I2C write failed\n");
return -EREMOTEIO;
}
}
// Writes a set of consecutive registers
-static int mt2060_writeregs(struct mt2060_state *state,u8 *buf, u8 len)
+static int mt2060_writeregs(struct mt2060_priv *priv,u8 *buf, u8 len)
{
struct i2c_msg msg = {
- .addr = state->config->i2c_address, .flags = 0, .buf = buf, .len = len
+ .addr = priv->cfg->i2c_address, .flags = 0, .buf = buf, .len = len
};
- if (i2c_transfer(state->i2c, &msg, 1) != 1) {
+ if (i2c_transfer(priv->i2c, &msg, 1) != 1) {
printk(KERN_WARNING "mt2060 I2C write failed (len=%i)\n",(int)len);
return -EREMOTEIO;
}
};
// VGAG=3, V1CSE=1
-static u8 mt2060_config3[] = {
- REG_VGAG,
- 0x33
-};
-
-int mt2060_init(struct mt2060_state *state)
-{
- if (mt2060_writeregs(state,mt2060_config1,sizeof(mt2060_config1)))
- return -EREMOTEIO;
- if (mt2060_writeregs(state,mt2060_config3,sizeof(mt2060_config3)))
- return -EREMOTEIO;
- return 0;
-}
-EXPORT_SYMBOL(mt2060_init);
#ifdef MT2060_SPURCHECK
/* The function below calculates the frequency offset between the output frequency if2
#define IF2 36150 // IF2 frequency = 36.150 MHz
#define FREF 16000 // Quartz oscillator 16 MHz
-int mt2060_set(struct mt2060_state *state, struct dvb_frontend_parameters *fep)
+static int mt2060_set_params(struct dvb_frontend *fe, struct dvb_frontend_parameters *params)
{
+ struct mt2060_priv *priv;
int ret=0;
int i=0;
u32 freq;
u8 b[8];
u32 if1;
- if1 = state->if1_freq;
+ priv = fe->tuner_priv;
+
+ if1 = priv->if1_freq;
b[0] = REG_LO1B1;
b[1] = 0xFF;
- mt2060_writeregs(state,b,2);
- freq = fep->frequency / 1000; // Hz -> kHz
+ mt2060_writeregs(priv,b,2);
- f_lo1 = freq + if1 * 1000;
- f_lo1 = (f_lo1/250)*250;
- f_lo2 = f_lo1 - freq - IF2;
- f_lo2 = (f_lo2/50)*50;
+ freq = params->frequency / 1000; // Hz -> kHz
+ priv->bandwidth = (fe->ops.info.type == FE_OFDM) ? params->u.ofdm.bandwidth : 0;
+
+ f_lo1 = freq + if1 * 1000;
+ f_lo1 = (f_lo1 / 250) * 250;
+ f_lo2 = f_lo1 - freq - IF2;
+ // From the Comtech datasheet, the step used is 50kHz. The tuner chip could be more precise
+ f_lo2 = ((f_lo2 + 25) / 50) * 50;
+ priv->frequency = (f_lo1 - f_lo2 - IF2) * 1000,
#ifdef MT2060_SPURCHECK
// LO-related spurs detection and correction
f_lo2 += num1;
#endif
//Frequency LO1 = 16MHz * (DIV1 + NUM1/64 )
- div1 = f_lo1 / FREF;
- num1 = (64 * (f_lo1 % FREF) )/FREF;
+ num1 = f_lo1 / (FREF / 64);
+ div1 = num1 / 64;
+ num1 &= 0x3f;
// Frequency LO2 = 16MHz * (DIV2 + NUM2/8192 )
- div2 = f_lo2 / FREF;
- num2 = (16384 * (f_lo2 % FREF) /FREF +1)/2;
+ num2 = f_lo2 * 64 / (FREF / 128);
+ div2 = num2 / 8192;
+ num2 &= 0x1fff;
if (freq <= 95000) lnaband = 0xB0; else
if (freq <= 180000) lnaband = 0xA0; else
b[5] = ((num2 >>12) & 1) | (div2 << 1);
dprintk("IF1: %dMHz",(int)if1);
- dprintk("PLL freq: %d f_lo1: %d f_lo2: %d (kHz)",(int)freq,(int)f_lo1,(int)f_lo2);
- dprintk("PLL div1: %d num1: %d div2: %d num2: %d",(int)div1,(int)num1,(int)div2,(int)num2);
+ dprintk("PLL freq=%dkHz f_lo1=%dkHz f_lo2=%dkHz",(int)freq,(int)f_lo1,(int)f_lo2);
+ dprintk("PLL div1=%d num1=%d div2=%d num2=%d",(int)div1,(int)num1,(int)div2,(int)num2);
dprintk("PLL [1..5]: %2x %2x %2x %2x %2x",(int)b[1],(int)b[2],(int)b[3],(int)b[4],(int)b[5]);
- mt2060_writeregs(state,b,6);
+ mt2060_writeregs(priv,b,6);
//Waits for pll lock or timeout
- i=0;
+ i = 0;
do {
- mt2060_readreg(state,REG_LO_STATUS,b);
- if ((b[0] & 0x88)==0x88) break;
+ mt2060_readreg(priv,REG_LO_STATUS,b);
+ if ((b[0] & 0x88)==0x88)
+ break;
msleep(4);
i++;
} while (i<10);
return ret;
}
-EXPORT_SYMBOL(mt2060_set);
-/* from usbsnoop.log */
-static void mt2060_calibrate(struct mt2060_state *state)
+static void mt2060_calibrate(struct mt2060_priv *priv)
{
u8 b = 0;
int i = 0;
- if (mt2060_writeregs(state,mt2060_config1,sizeof(mt2060_config1)))
+ if (mt2060_writeregs(priv,mt2060_config1,sizeof(mt2060_config1)))
return;
- if (mt2060_writeregs(state,mt2060_config2,sizeof(mt2060_config2)))
+ if (mt2060_writeregs(priv,mt2060_config2,sizeof(mt2060_config2)))
return;
do {
b |= (1 << 6); // FM1SS;
- mt2060_writereg(state, REG_LO2C1,b);
+ mt2060_writereg(priv, REG_LO2C1,b);
msleep(20);
if (i == 0) {
b |= (1 << 7); // FM1CA;
- mt2060_writereg(state, REG_LO2C1,b);
+ mt2060_writereg(priv, REG_LO2C1,b);
b &= ~(1 << 7); // FM1CA;
msleep(20);
}
b &= ~(1 << 6); // FM1SS
- mt2060_writereg(state, REG_LO2C1,b);
+ mt2060_writereg(priv, REG_LO2C1,b);
msleep(20);
i++;
} while (i < 9);
i = 0;
- while (i++ < 10 && mt2060_readreg(state, REG_MISC_STAT, &b) == 0 && (b & (1 << 6)) == 0)
+ while (i++ < 10 && mt2060_readreg(priv, REG_MISC_STAT, &b) == 0 && (b & (1 << 6)) == 0)
msleep(20);
if (i < 10) {
- mt2060_readreg(state, REG_FM_FREQ, &state->fmfreq); // now find out, what is fmreq used for :)
- dprintk("calibration was successful: %d", state->fmfreq);
+ mt2060_readreg(priv, REG_FM_FREQ, &priv->fmfreq); // now find out, what is fmreq used for :)
+ dprintk("calibration was successful: %d", (int)priv->fmfreq);
} else
dprintk("FMCAL timed out");
}
+static int mt2060_calc_regs(struct dvb_frontend *fe, struct dvb_frontend_parameters *params, u8 *buf, int buf_len)
+{
+ return -ENODEV;
+}
+
+static int mt2060_get_frequency(struct dvb_frontend *fe, u32 *frequency)
+{
+ struct mt2060_priv *priv = fe->tuner_priv;
+ *frequency = priv->frequency;
+ return 0;
+}
+
+static int mt2060_get_bandwidth(struct dvb_frontend *fe, u32 *bandwidth)
+{
+ struct mt2060_priv *priv = fe->tuner_priv;
+ *bandwidth = priv->bandwidth;
+ return 0;
+}
+
+static int mt2060_sleep(struct dvb_frontend *fe)
+{
+ struct mt2060_priv *priv = fe->tuner_priv;
+ return mt2060_writereg(priv, REG_VGAG,0x30);
+}
+
+static int mt2060_release(struct dvb_frontend *fe)
+{
+ kfree(fe->tuner_priv);
+ fe->tuner_priv = NULL;
+ return 0;
+}
+
+static const struct dvb_tuner_ops mt2060_tuner_ops = {
+ .info = {
+ .name = "Microtune MT2060",
+ .frequency_min = 48000000,
+ .frequency_max = 860000000,
+ .frequency_step = 50000,
+ },
+
+ .release = mt2060_release,
+
+ .sleep = mt2060_sleep,
+
+ .set_params = mt2060_set_params,
+ .calc_regs = mt2060_calc_regs,
+ .get_frequency = mt2060_get_frequency,
+ .get_bandwidth = mt2060_get_bandwidth
+};
+
/* This functions tries to identify a MT2060 tuner by reading the PART/REV register. This is hasty. */
-int mt2060_attach(struct mt2060_state *state, struct mt2060_config *config, struct i2c_adapter *i2c,u16 if1)
+int mt2060_attach(struct dvb_frontend *fe, struct i2c_adapter *i2c, struct mt2060_config *cfg, u16 if1)
{
+ struct mt2060_priv *priv = NULL;
u8 id = 0;
- memset(state,0,sizeof(struct mt2060_state));
- state->config = config;
- state->i2c = i2c;
- state->if1_freq = if1;
+ priv = kzalloc(sizeof(struct mt2060_priv), GFP_KERNEL);
+ if (priv == NULL)
+ return -ENOMEM;
- if (mt2060_readreg(state,REG_PART_REV,&id) != 0)
- return -ENODEV;
+ priv->cfg = cfg;
+ priv->i2c = i2c;
+ priv->if1_freq = if1;
- if (id != PART_REV)
+ if (mt2060_readreg(priv,REG_PART_REV,&id) != 0) {
+ kfree(priv);
return -ENODEV;
+ }
+ if (id != PART_REV) {
+ kfree(priv);
+ return -ENODEV;
+ }
printk(KERN_INFO "MT2060: successfully identified\n");
+ memcpy(&fe->ops.tuner_ops, &mt2060_tuner_ops, sizeof(struct dvb_tuner_ops));
+
+ fe->tuner_priv = priv;
- mt2060_calibrate(state);
+ mt2060_calibrate(priv);
return 0;
}
git.openpandora.org / pandora-kernel.git / commitdiff