Here are some spelling corrections for drivers/i2c.
occured -> occurred
intialization -> initialization
Everytime -> Every time
transfering -> transferring
relevent -> relevant
continous -> continuous
neccessary -> necessary
explicitely -> explicitly
Celcius -> Celsius
differenciate -> differentiate
Signed-off-by: Steven Cole <elenstev@mesatop.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
/*
* Generate a start condition on the i2c bus.
*
- * returns after the start condition has occured
+ * returns after the start condition has occurred
*/
static void pca_start(struct i2c_algo_pca_data *adap)
{
/*
* Generate a repeated start condition on the i2c bus
*
- * return after the repeated start condition has occured
+ * return after the repeated start condition has occurred
*/
static void pca_repeated_start(struct i2c_algo_pca_data *adap)
{
dev->irq = iic_force_poll ? -1 : ocp->def->irq;
if (dev->irq >= 0){
- /* Disable interrupts until we finish intialization,
+ /* Disable interrupts until we finish initialization,
assumes level-sensitive IRQ setup...
*/
iic_interrupt_mode(dev, 0);
u32 cr = IOP3XX_ICR_GCD | IOP3XX_ICR_SCLEN | IOP3XX_ICR_UE;
/*
- * Everytime unit enable is asserted, GPOD needs to be cleared
+ * Every time unit enable is asserted, GPOD needs to be cleared
* on IOP321 to avoid data corruption on the bus.
*/
#ifdef CONFIG_ARCH_IOP321
/* s3c24xx_i2c_xfer
*
* first port of call from the i2c bus code when an message needs
- * transfering across the i2c bus.
+ * transferring across the i2c bus.
*/
static int s3c24xx_i2c_xfer(struct i2c_adapter *adap,
/*
* That function checks the cases where the fan reading is not
- * relevent. It is used to provide 0 as fan reading when the fan is
+ * relevant. It is used to provide 0 as fan reading when the fan is
* not supposed to run
*/
static int trust_fan_readings(struct adm1031_data *data, int chan)
static void ds1621_init_client(struct i2c_client *client)
{
int reg = ds1621_read_value(client, DS1621_REG_CONF);
- /* switch to continous conversion mode */
+ /* switch to continuous conversion mode */
reg &= ~ DS1621_REG_CONFIG_1SHOT;
/* setup output polarity */
data->temp_max = ds1621_read_value(client,
DS1621_REG_TEMP_MAX);
- /* reset alarms if neccessary */
+ /* reset alarms if necessary */
new_conf = data->conf;
if (data->temp < data->temp_min)
new_conf &= ~DS1621_ALARM_TEMP_LOW;
return 0;
}
-/* The SMBus locks itself, but ISA access must be locked explicitely!
+/* The SMBus locks itself, but ISA access must be locked explicitly!
We don't want to lock the whole ISA bus, so we lock each client
separately.
We ignore the IT87 BUSY flag at this moment - it could lead to deadlocks,
return i2c_smbus_read_byte_data(client, reg);
}
-/* The SMBus locks itself, but ISA access muse be locked explicitely!
+/* The SMBus locks itself, but ISA access muse be locked explicitly!
We don't want to lock the whole ISA bus, so we lock each client
separately.
We ignore the IT87 BUSY flag at this moment - it could lead to deadlocks,
* Conversions and various macros
* For tachometer counts, the LM63 uses 16-bit values.
* For local temperature and high limit, remote critical limit and hysteresis
- * value, it uses signed 8-bit values with LSB = 1 degree Celcius.
+ * value, it uses signed 8-bit values with LSB = 1 degree Celsius.
* For remote temperature, low and high limits, it uses signed 11-bit values
- * with LSB = 0.125 degree Celcius, left-justified in 16-bit registers.
+ * with LSB = 0.125 degree Celsius, left-justified in 16-bit registers.
*/
#define FAN_FROM_REG(reg) ((reg) == 0xFFFC || (reg) == 0 ? 0 : \
return 0;
}
-/* The SMBus locks itself, but ISA access must be locked explicitely!
+/* The SMBus locks itself, but ISA access must be locked explicitly!
We don't want to lock the whole ISA bus, so we lock each client
separately.
We ignore the LM78 BUSY flag at this moment - it could lead to deadlocks,
return i2c_smbus_read_byte_data(client, reg);
}
-/* The SMBus locks itself, but ISA access muse be locked explicitely!
+/* The SMBus locks itself, but ISA access muse be locked explicitly!
We don't want to lock the whole ISA bus, so we lock each client
separately.
We ignore the LM78 BUSY flag at this moment - it could lead to deadlocks,
/*
* Conversions and various macros
- * The LM83 uses signed 8-bit values with LSB = 1 degree Celcius.
+ * The LM83 uses signed 8-bit values with LSB = 1 degree Celsius.
*/
#define TEMP_FROM_REG(val) ((val) * 1000)
* Complete datasheets can be obtained from National's website at:
* http://www.national.com/pf/LM/LM89.html
* http://www.national.com/pf/LM/LM99.html
- * Note that there is no way to differenciate between both chips.
+ * Note that there is no way to differentiate between both chips.
*
* This driver also supports the LM86, another sensor chip made by
* National Semiconductor. It is exactly similar to the LM90 except it
* chips made by Maxim. These chips are similar to the LM86. Complete
* datasheet can be obtained at Maxim's website at:
* http://www.maxim-ic.com/quick_view2.cfm/qv_pk/2578
- * Note that there is no easy way to differenciate between the three
+ * Note that there is no easy way to differentiate between the three
* variants. The extra address and features of the MAX6659 are not
* supported by this driver.
*
/*
* Conversions and various macros
* For local temperatures and limits, critical limits and the hysteresis
- * value, the LM90 uses signed 8-bit values with LSB = 1 degree Celcius.
+ * value, the LM90 uses signed 8-bit values with LSB = 1 degree Celsius.
* For remote temperatures and limits, it uses signed 11-bit values with
- * LSB = 0.125 degree Celcius, left-justified in 16-bit registers.
+ * LSB = 0.125 degree Celsius, left-justified in 16-bit registers.
*/
#define TEMP1_FROM_REG(val) ((val) * 1000)
git.openpandora.org / pandora-kernel.git / commitdiff