arm: convert pcm037 platform to use smsc911x

Updated to also specify SMSC911X_FORCE_INTERNAL_PHY, as the external phy
detection hardware strap is incorrectly pulled high on this platform.

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>

diff --git a/arch/arm/mach-mx3/pcm037.c b/arch/arm/mach-mx3/pcm037.c
index 5fce022..c3648ef 100644 (file)
--- a/arch/arm/mach-mx3/pcm037.c
+++ b/arch/arm/mach-mx3/pcm037.c
@@ -24,7 +24,7 @@
 #include <linux/mtd/plat-ram.h>
 #include <linux/memory.h>
 #include <linux/gpio.h>
-#include <linux/smc911x.h>
+#include <linux/smsc911x.h>
 #include <linux/interrupt.h>
 #include <linux/i2c.h>
 #include <linux/i2c/at24.h>
@@ -70,7 +70,7 @@ static struct imxuart_platform_data uart_pdata = {
        .flags = IMXUART_HAVE_RTSCTS,
 };
 
-static struct resource smc911x_resources[] = {
+static struct resource smsc911x_resources[] = {
        [0] = {
                .start          = CS1_BASE_ADDR + 0x300,
                .end            = CS1_BASE_ADDR + 0x300 + SZ_64K - 1,
@@ -79,22 +79,25 @@ static struct resource smc911x_resources[] = {
        [1] = {
                .start          = IOMUX_TO_IRQ(MX31_PIN_GPIO3_1),
                .end            = IOMUX_TO_IRQ(MX31_PIN_GPIO3_1),
-               .flags          = IORESOURCE_IRQ,
+               .flags          = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
        },
 };
 
-static struct smc911x_platdata smc911x_info = {
-       .flags          = SMC911X_USE_32BIT,
-       .irq_flags      = IRQF_SHARED | IRQF_TRIGGER_LOW,
+static struct smsc911x_platform_config smsc911x_info = {
+       .flags          = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY |
+                         SMSC911X_SAVE_MAC_ADDRESS,
+       .irq_polarity   = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+       .irq_type       = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+       .phy_interface  = PHY_INTERFACE_MODE_MII,
 };
 
 static struct platform_device pcm037_eth = {
-       .name           = "smc911x",
+       .name           = "smsc911x",
        .id             = -1,
-       .num_resources  = ARRAY_SIZE(smc911x_resources),
-       .resource       = smc911x_resources,
+       .num_resources  = ARRAY_SIZE(smsc911x_resources),
+       .resource       = smsc911x_resources,
        .dev            = {
-               .platform_data = &smc911x_info,
+               .platform_data = &smsc911x_info,
        },
 };