#include <linux/irq.h>
#include <linux/irqdomain.h>
#include <linux/of.h>
+ #include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/micrel_phy.h>
#include <asm/hardware/cache-l2x0.h>
#include <asm/hardware/gic.h>
#include <asm/mach/arch.h>
#include <mach/common.h>
#include <mach/hardware.h>
+ void imx6q_restart(char mode, const char *cmd)
+ {
+ struct device_node *np;
+ void __iomem *wdog_base;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-wdt");
+ wdog_base = of_iomap(np, 0);
+ if (!wdog_base)
+ goto soft;
+
+ imx_src_prepare_restart();
+
+ /* enable wdog */
+ writew_relaxed(1 << 2, wdog_base);
+ /* write twice to ensure the request will not get ignored */
+ writew_relaxed(1 << 2, wdog_base);
+
+ /* wait for reset to assert ... */
+ mdelay(500);
+
+ pr_err("Watchdog reset failed to assert reset\n");
+
+ /* delay to allow the serial port to show the message */
+ mdelay(50);
+
+ soft:
+ /* we'll take a jump through zero as a poor second */
+ soft_restart(0);
+ }
+
+/* For imx6q sabrelite board: set KSZ9021RN RGMII pad skew */
+static int ksz9021rn_phy_fixup(struct phy_device *phydev)
+{
+ /* min rx data delay */
+ phy_write(phydev, 0x0b, 0x8105);
+ phy_write(phydev, 0x0c, 0x0000);
+
+ /* max rx/tx clock delay, min rx/tx control delay */
+ phy_write(phydev, 0x0b, 0x8104);
+ phy_write(phydev, 0x0c, 0xf0f0);
+ phy_write(phydev, 0x0b, 0x104);
+
+ return 0;
+}
+
static void __init imx6q_init_machine(void)
{
+ if (of_machine_is_compatible("fsl,imx6q-sabrelite"))
+ phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
+ ksz9021rn_phy_fixup);
+
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
imx6q_pm_init();
MACHINE_START(TI8168EVM, "ti8168evm")
/* Maintainer: Texas Instruments */
.atag_offset = 0x100,
- .map_io = ti8168_evm_map_io,
- .init_early = ti816x_init_early,
- .init_irq = ti816x_init_irq,
+ .map_io = ti81xx_map_io,
+ .init_early = ti81xx_init_early,
+ .init_irq = ti81xx_init_irq,
+ .timer = &omap3_timer,
+ .init_machine = ti81xx_evm_init,
++ .restart = omap_prcm_restart,
+MACHINE_END
+
+MACHINE_START(TI8148EVM, "ti8148evm")
+ /* Maintainer: Texas Instruments */
+ .atag_offset = 0x100,
+ .map_io = ti81xx_map_io,
+ .init_early = ti81xx_init_early,
+ .init_irq = ti81xx_init_irq,
.timer = &omap3_timer,
- .init_machine = ti8168_evm_init,
+ .init_machine = ti81xx_evm_init,
+ .restart = omap_prcm_restart,
MACHINE_END
void omap3630_init_early(void);
void omap3_init_early(void); /* Do not use this one */
void am35xx_init_early(void);
-void ti816x_init_early(void);
+void ti81xx_init_early(void);
void omap4430_init_early(void);
+ void omap_prcm_restart(char, const char *);
/*
* IO bases for various OMAP processors
select S3C_DEV_I2C1
select S3C_DEV_WDT
select S3C_DEV_RTC
- select S3C64XX_DEV_SPI
+ select S3C64XX_DEV_SPI0
- select S3C24XX_GPIO_EXTRA128
+ select SAMSUNG_GPIO_EXTRA128
select I2C
help
Machine support for the Wolfson Cragganmore S3C6410 variant.
.handle_irq = gic_handle_irq,
.timer = &tegra_timer,
.init_machine = tegra_dt_init,
- .dt_compat = tegra_dt_board_compat,
+ .restart = tegra_assert_system_reset,
+ .dt_compat = tegra20_dt_board_compat,
MACHINE_END
#include "clock.h"
#include "fuse.h"
- void (*arch_reset)(char mode, const char *cmd) = tegra_assert_system_reset;
-
+#ifdef CONFIG_OF
+static const struct of_device_id tegra_dt_irq_match[] __initconst = {
+ { .compatible = "arm,cortex-a9-gic", .data = gic_of_init },
+ { }
+};
+
+void __init tegra_dt_init_irq(void)
+{
+ tegra_init_irq();
+ of_irq_init(tegra_dt_irq_match);
+}
+#endif
+
void tegra_assert_system_reset(char mode, const char *cmd)
{
- void __iomem *reset = IO_ADDRESS(TEGRA_CLK_RESET_BASE + 0x04);
+ void __iomem *reset = IO_ADDRESS(TEGRA_PMC_BASE + 0);
u32 reg;
- /* use *_related to avoid spinlock since caches are off */
reg = readl_relaxed(reset);
- reg |= 0x04;
+ reg |= 0x10;
writel_relaxed(reg, reset);
}
git.openpandora.org / pandora-kernel.git / commitdiff