int nsgs, int *bucket_map);
static __devinit void hpsa_put_ctlr_into_performant_mode(struct ctlr_info *h);
static inline u32 next_command(struct ctlr_info *h);
+static int __devinit hpsa_find_cfg_addrs(struct pci_dev *pdev,
+ void __iomem *vaddr, u32 *cfg_base_addr, u64 *cfg_base_addr_index,
+ u64 *cfg_offset);
+static int __devinit hpsa_pci_find_memory_BAR(struct pci_dev *pdev,
+ unsigned long *memory_bar);
static DEVICE_ATTR(raid_level, S_IRUGO, raid_level_show, NULL);
static DEVICE_ATTR(lunid, S_IRUGO, lunid_show, NULL);
return 0;
}
+static int hpsa_controller_hard_reset(struct pci_dev *pdev,
+ void * __iomem vaddr, bool use_doorbell)
+{
+ u16 pmcsr;
+ int pos;
+
+ if (use_doorbell) {
+ /* For everything after the P600, the PCI power state method
+ * of resetting the controller doesn't work, so we have this
+ * other way using the doorbell register.
+ */
+ dev_info(&pdev->dev, "using doorbell to reset controller\n");
+ writel(DOORBELL_CTLR_RESET, vaddr + SA5_DOORBELL);
+ msleep(1000);
+ } else { /* Try to do it the PCI power state way */
+
+ /* Quoting from the Open CISS Specification: "The Power
+ * Management Control/Status Register (CSR) controls the power
+ * state of the device. The normal operating state is D0,
+ * CSR=00h. The software off state is D3, CSR=03h. To reset
+ * the controller, place the interface device in D3 then to D0,
+ * this causes a secondary PCI reset which will reset the
+ * controller." */
+
+ pos = pci_find_capability(pdev, PCI_CAP_ID_PM);
+ if (pos == 0) {
+ dev_err(&pdev->dev,
+ "hpsa_reset_controller: "
+ "PCI PM not supported\n");
+ return -ENODEV;
+ }
+ dev_info(&pdev->dev, "using PCI PM to reset controller\n");
+ /* enter the D3hot power management state */
+ pci_read_config_word(pdev, pos + PCI_PM_CTRL, &pmcsr);
+ pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
+ pmcsr |= PCI_D3hot;
+ pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+
+ msleep(500);
+
+ /* enter the D0 power management state */
+ pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
+ pmcsr |= PCI_D0;
+ pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+
+ msleep(500);
+ }
+ return 0;
+}
+
/* This does a hard reset of the controller using PCI power management
- * states.
+ * states or the using the doorbell register.
*/
-static __devinit int hpsa_hard_reset_controller(struct pci_dev *pdev)
+static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
{
- u16 pmcsr, saved_config_space[32];
- int i, pos;
+ u16 saved_config_space[32];
+ u64 cfg_offset;
+ u32 cfg_base_addr;
+ u64 cfg_base_addr_index;
+ void __iomem *vaddr;
+ unsigned long paddr;
+ u32 misc_fw_support, active_transport;
+ int rc, i;
+ struct CfgTable __iomem *cfgtable;
+ bool use_doorbell;
- dev_info(&pdev->dev, "using PCI PM to reset controller\n");
- /* This is very nearly the same thing as
+ /* For controllers as old as the P600, this is very nearly
+ * the same thing as
*
* pci_save_state(pci_dev);
* pci_set_power_state(pci_dev, PCI_D3hot);
* violate the ordering requirements for restoring the
* configuration space from the CCISS document (see the
* comment below). So we roll our own ....
+ *
+ * For controllers newer than the P600, the pci power state
+ * method of resetting doesn't work so we have another way
+ * using the doorbell register.
*/
-
for (i = 0; i < 32; i++)
pci_read_config_word(pdev, 2*i, &saved_config_space[i]);
- pos = pci_find_capability(pdev, PCI_CAP_ID_PM);
- if (pos == 0) {
- dev_err(&pdev->dev,
- "hpsa_reset_controller: PCI PM not supported\n");
- return -ENODEV;
- }
-
- /* Quoting from the Open CISS Specification: "The Power
- * Management Control/Status Register (CSR) controls the power
- * state of the device. The normal operating state is D0,
- * CSR=00h. The software off state is D3, CSR=03h. To reset
- * the controller, place the interface device in D3 then to
- * D0, this causes a secondary PCI reset which will reset the
- * controller."
- */
- /* enter the D3hot power management state */
- pci_read_config_word(pdev, pos + PCI_PM_CTRL, &pmcsr);
- pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
- pmcsr |= PCI_D3hot;
- pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+ /* find the first memory BAR, so we can find the cfg table */
+ rc = hpsa_pci_find_memory_BAR(pdev, &paddr);
+ if (rc)
+ return rc;
+ vaddr = remap_pci_mem(paddr, 0x250);
+ if (!vaddr)
+ return -ENOMEM;
- msleep(500);
+ /* find cfgtable in order to check if reset via doorbell is supported */
+ rc = hpsa_find_cfg_addrs(pdev, vaddr, &cfg_base_addr,
+ &cfg_base_addr_index, &cfg_offset);
+ if (rc)
+ goto unmap_vaddr;
+ cfgtable = remap_pci_mem(pci_resource_start(pdev,
+ cfg_base_addr_index) + cfg_offset, sizeof(*cfgtable));
+ if (!cfgtable) {
+ rc = -ENOMEM;
+ goto unmap_vaddr;
+ }
- /* enter the D0 power management state */
- pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
- pmcsr |= PCI_D0;
- pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+ /* If reset via doorbell register is supported, use that. */
+ misc_fw_support = readl(&cfgtable->misc_fw_support);
+ use_doorbell = misc_fw_support & MISC_FW_DOORBELL_RESET;
- msleep(500);
+ rc = hpsa_controller_hard_reset(pdev, vaddr, use_doorbell);
+ if (rc)
+ goto unmap_cfgtable;
/* Restore the PCI configuration space. The Open CISS
* Specification says, "Restore the PCI Configuration
wmb();
pci_write_config_word(pdev, 4, saved_config_space[2]);
- return 0;
+ /* Some devices (notably the HP Smart Array 5i Controller)
+ need a little pause here */
+ msleep(HPSA_POST_RESET_PAUSE_MSECS);
+
+ /* Controller should be in simple mode at this point. If it's not,
+ * It means we're on one of those controllers which doesn't support
+ * the doorbell reset method and on which the PCI power management reset
+ * method doesn't work (P800, for example.)
+ * In those cases, pretend the reset worked and hope for the best.
+ */
+ active_transport = readl(&cfgtable->TransportActive);
+ if (active_transport & PERFORMANT_MODE) {
+ dev_warn(&pdev->dev, "Unable to successfully reset controller,"
+ " proceeding anyway.\n");
+ rc = -ENOTSUPP;
+ }
+
+unmap_cfgtable:
+ iounmap(cfgtable);
+
+unmap_vaddr:
+ iounmap(vaddr);
+ return rc;
}
/*
static __devinit int hpsa_init_reset_devices(struct pci_dev *pdev)
{
- int i;
+ int rc, i;
if (!reset_devices)
return 0;
- /* Reset the controller with a PCI power-cycle */
- if (hpsa_hard_reset_controller(pdev) || hpsa_reset_msi(pdev))
- return -ENODEV;
+ /* Reset the controller with a PCI power-cycle or via doorbell */
+ rc = hpsa_kdump_hard_reset_controller(pdev);
- /* Some devices (notably the HP Smart Array 5i Controller)
- need a little pause here */
- msleep(HPSA_POST_RESET_PAUSE_MSECS);
+ /* -ENOTSUPP here means we cannot reset the controller
+ * but it's already (and still) up and running in
+ * "performant mode".
+ */
+ if (rc == -ENOTSUPP)
+ return 0; /* just try to do the kdump anyhow. */
+ if (rc)
+ return -ENODEV;
+ if (hpsa_reset_msi(pdev))
+ return -ENODEV;
/* Now try to get the controller to respond to a no-op */
for (i = 0; i < HPSA_POST_RESET_NOOP_RETRIES; i++) {
git.openpandora.org / pandora-kernel.git / commitdiff