revise anomaly handling by basing things on the compiler not the kconfig defines,
so the header is stable and usable outside of the kernel. This also allows us to
move some code from preprocessing to compiling (gcc culls dead code)
which should help with code quality (readability, catch minor bugs, etc...).
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
SET_GPIO_SC(maska)
SET_GPIO_SC(maskb)
-#if defined(ANOMALY_05000311)
+#if ANOMALY_05000311
void set_gpio_data(unsigned short gpio, unsigned short arg)
{
unsigned long flags;
#endif
-#if defined(ANOMALY_05000311)
+#if ANOMALY_05000311
void set_gpio_toggle(unsigned short gpio)
{
unsigned long flags;
SET_GPIO_P(maskb)
-#if defined(ANOMALY_05000311)
+#if ANOMALY_05000311
void set_gpiop_data(unsigned short gpio, unsigned short arg)
{
unsigned long flags;
GET_GPIO(maskb)
-#if defined(ANOMALY_05000311)
+#if ANOMALY_05000311
unsigned short get_gpio_data(unsigned short gpio)
{
unsigned long flags;
GET_GPIO_P(maska)
GET_GPIO_P(maskb)
-#if defined(ANOMALY_05000311)
+#if ANOMALY_05000311
unsigned short get_gpiop_data(unsigned short gpio)
{
unsigned long flags;
cplb_data[i].psize,
cplb_data[i].i_conf);
} else {
-#if (defined(CONFIG_BLKFIN_CACHE) && defined(ANOMALY_05000263))
- if (i == SDRAM_KERN) {
+#if defined(CONFIG_BLKFIN_CACHE)
+ if (ANOMALY_05000263 && i == SDRAM_KERN) {
fill_cplbtab(t,
cplb_data[i].start,
cplb_data[i].end,
cclk = get_cclk();
sclk = get_sclk();
-#if !defined(CONFIG_BFIN_KERNEL_CLOCK) && defined(ANOMALY_05000273)
- if (cclk == sclk)
+#if !defined(CONFIG_BFIN_KERNEL_CLOCK)
+ if (ANOMALY_05000273 && cclk == sclk)
panic("ANOMALY 05000273, SCLK can not be same as CCLK");
#endif
-#if defined(ANOMALY_05000266)
- bfin_read_IMDMA_D0_IRQ_STATUS();
- bfin_read_IMDMA_D1_IRQ_STATUS();
+#ifdef BF561_FAMILY
+ if (ANOMALY_05000266) {
+ bfin_read_IMDMA_D0_IRQ_STATUS();
+ bfin_read_IMDMA_D1_IRQ_STATUS();
+ }
#endif
#ifdef DEBUG_SERIAL_EARLY_INIT
&& ((unsigned long *)mtd_phys)[1] == ROMSB_WORD1)
mtd_size =
PAGE_ALIGN(be32_to_cpu(((unsigned long *)mtd_phys)[2]));
-# if (defined(CONFIG_BLKFIN_CACHE) && defined(ANOMALY_05000263))
+# if (defined(CONFIG_BLKFIN_CACHE) && ANOMALY_05000263)
/* Due to a Hardware Anomaly we need to limit the size of usable
* instruction memory to max 60MB, 56 if HUNT_FOR_ZERO is on
* 05000263 - Hardware loop corrupted when taking an ICPLB exception
_ebss = memory_mtd_start; /* define _ebss for compatible */
#endif /* CONFIG_MTD_UCLINUX */
-#if (defined(CONFIG_BLKFIN_CACHE) && defined(ANOMALY_05000263))
+#if (defined(CONFIG_BLKFIN_CACHE) && ANOMALY_05000263)
/* Due to a Hardware Anomaly we need to limit the size of usable
* instruction memory to max 60MB, 56 if HUNT_FOR_ZERO is on
* 05000263 - Hardware loop corrupted when taking an ICPLB exception
printk(KERN_INFO "Processor Speed: %lu MHz core clock and %lu Mhz System Clock\n",
cclk / 1000000, sclk / 1000000);
-#if defined(ANOMALY_05000273)
- if ((cclk >> 1) <= sclk)
+ if (ANOMALY_05000273 && (cclk >> 1) <= sclk)
printk("\n\n\nANOMALY_05000273: CCLK must be >= 2*SCLK !!!\n\n\n");
-#endif
printk(KERN_INFO "Board Memory: %ldMB\n", physical_mem_end >> 20);
printk(KERN_INFO "Kernel Managed Memory: %ldMB\n", _ramend >> 20);
LSETUP (.Lquad_loop_s, .Lquad_loop_e) LC0=P1;
.Lquad_loop_s:
-#ifdef ANOMALY_05000202
+#if ANOMALY_05000202
R0 = [P0++];
R1 = [I0++];
#else
R0 = R1;
I1 = P1;
R3 = [I1++];
-#ifdef ANOMALY_05000202
+#if ANOMALY_05000202
.Lword_loops:
[P0++] = R3;
.Lword_loope:
R1 = [I0++];
LSETUP (.Lquad_loops, .Lquad_loope) LC0=P1;
-#ifdef ANOMALY_05000202
+#if ANOMALY_05000202
.Lquad_loops:
[P0++] = R1;
.Lquad_loope:
R1 = B[P3--] (Z);
CC = P2 == 0;
IF CC JUMP .Lno_loop;
-#ifdef ANOMALY_05000245
+#if ANOMALY_05000245
NOP;
NOP;
#endif
R0 = R0 & R1;
/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
R0 = R0 & R1;
/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
p0.l = .LWAIT_HERE;
p0.h = .LWAIT_HERE;
reti = p0;
-#if defined(ANOMALY_05000281)
+#if ANOMALY_05000281
nop; nop; nop;
#endif
rti;
R0 = R0 & R1;
/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
R0 = R0 & R1;
/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
*/
p0.h = hi(BFIN_PORT_MUX);
p0.l = lo(BFIN_PORT_MUX);
-#ifdef ANOMALY_05000212
+#if ANOMALY_05000212
R0.L = W[P0]; /* Read */
SSYNC;
#endif
R0 = (PGDE_UART | PFTE_UART)(Z);
-#ifdef ANOMALY_05000212
+#if ANOMALY_05000212
W[P0] = R0.L; /* Write */
SSYNC;
#endif
p0.h = hi(PORTF_FER);
p0.l = lo(PORTF_FER);
-#ifdef ANOMALY_05000212
+#if ANOMALY_05000212
R0.L = W[P0]; /* Read */
SSYNC;
#endif
R0 = 0x000F(Z);
-#ifdef ANOMALY_05000212
+#if ANOMALY_05000212
W[P0] = R0.L; /* Write */
SSYNC;
#endif
p0.l = .LWAIT_HERE;
p0.h = .LWAIT_HERE;
reti = p0;
-#if defined(ANOMALY_05000281)
+#if ANOMALY_05000281
nop; nop; nop;
#endif
rti;
p0.l = .LWAIT_HERE;
p0.h = .LWAIT_HERE;
reti = p0;
-#if defined (ANOMALY_05000281)
+#if ANOMALY_05000281
nop;
nop;
nop;
R0 = ~ENICPLB;
R0 = R0 & R1;
- /* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
R0 = R0 & R1;
/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
CLI R2;
SSYNC;
#endif
[p0] = R0;
SSYNC;
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
STI R2;
#endif
p0.l = .LWAIT_HERE;
p0.h = .LWAIT_HERE;
reti = p0;
-#if defined(ANOMALY_05000281)
+#if ANOMALY_05000281
nop; nop; nop;
#endif
rti;
.text
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
#if defined(CONFIG_BLKFIN_CACHE)
ENTRY(_bfin_write_IMEM_CONTROL)
P3.L = _page_size_table; /* retrieve end address */
P3.H = _page_size_table; /* retrieve end address */
R3 = 0x1002; /* 16th - position, 2 bits -length */
-#ifdef ANOMALY_05000209
+#if ANOMALY_05000209
nop; /* Anomaly 05000209 */
#endif
R7 = EXTRACT(R1,R3.l);
* patch up CPLB misses on the kernel stack.
*/
ENTRY(_ex_dcplb)
-#if defined(ANOMALY_05000261)
+#if ANOMALY_05000261
/*
* Work around an anomaly: if we see a new DCPLB fault, return
* without doing anything. Then, if we get the same fault again,
_return_from_exception:
DEBUG_START_HWTRACE(p5, r7)
-#ifdef ANOMALY_05000257
+#if ANOMALY_05000257
R7=LC0;
LC0=R7;
R7=LC1;
p1.h = _schedule_and_signal_from_int;
[p0] = p1;
csync;
-#if defined(ANOMALY_05000281)
+#if ANOMALY_05000281
r0.l = lo(CONFIG_BOOT_LOAD);
r0.h = hi(CONFIG_BOOT_LOAD);
reti = r0;
ENDPROC(_return_from_int)
ENTRY(_lower_to_irq14)
-#if defined(ANOMALY_05000281)
+#if ANOMALY_05000281
r0.l = lo(CONFIG_BOOT_LOAD);
r0.h = hi(CONFIG_BOOT_LOAD);
reti = r0;
.endr
_exception_stack_top:
-#if defined(ANOMALY_05000261)
+#if ANOMALY_05000261
/* Used by the assembly entry point to work around an anomaly. */
_last_cplb_fault_retx:
.long 0;
fp = 0;
#endif
-#if defined (ANOMALY_05000283) || defined (ANOMALY_05000315)
+#if ANOMALY_05000283 || ANOMALY_05000315
cc = r7 == r7;
p5.h = 0xffc0;
p5.l = 0x0014;
#ifdef CONFIG_FRAME_POINTER
fp = 0;
#endif
-#ifdef ANOMALY_05000283
+#if ANOMALY_05000283
cc = r7 == r7;
p5.h = 0xffc0;
p5.l = 0x0014;
#ifdef CONFIG_FRAME_POINTER
fp = 0;
#endif
-#ifdef ANOMALY_05000283
+#if ANOMALY_05000283
cc = r7 == r7;
p5.h = 0xffc0;
p5.l = 0x0014;
#ifndef __ASSEMBLY__
/* SSYNC implementation for C file */
-#if defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
-static inline void SSYNC (void)
+static inline void SSYNC(void)
{
int _tmp;
- __asm__ __volatile__ ("cli %0;\n\t"
- "nop;nop;\n\t"
- "ssync;\n\t"
- "sti %0;\n\t"
- :"=d"(_tmp):);
+ if (ANOMALY_05000312 && ANOMALY_05000244)
+ __asm__ __volatile__(
+ "cli %0;"
+ "nop;"
+ "nop;"
+ "ssync;"
+ "sti %0;"
+ : "=d" (_tmp)
+ );
+ else if (ANOMALY_05000312 && !ANOMALY_05000244)
+ __asm__ __volatile__(
+ "cli %0;"
+ "ssync;"
+ "sti %0;"
+ : "=d" (_tmp)
+ );
+ else if (!ANOMALY_05000312 && ANOMALY_05000244)
+ __asm__ __volatile__(
+ "nop;"
+ "nop;"
+ "nop;"
+ "ssync;"
+ );
+ else
+ __asm__ __volatile__("ssync;");
}
-#elif defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
-static inline void SSYNC (void)
-{
- int _tmp;
- __asm__ __volatile__ ("cli %0;\n\t"
- "ssync;\n\t"
- "sti %0;\n\t"
- :"=d"(_tmp):);
-}
-#elif !defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
-static inline void SSYNC (void)
-{
- __asm__ __volatile__ ("nop; nop; nop;\n\t"
- "ssync;\n\t"
- ::);
-}
-#elif !defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
-static inline void SSYNC (void)
-{
- __asm__ __volatile__ ("ssync;\n\t");
-}
-#endif
/* CSYNC implementation for C file */
-#if defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
-static inline void CSYNC (void)
+static inline void CSYNC(void)
{
int _tmp;
- __asm__ __volatile__ ("cli %0;\n\t"
- "nop;nop;\n\t"
- "csync;\n\t"
- "sti %0;\n\t"
- :"=d"(_tmp):);
-}
-#elif defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
-static inline void CSYNC (void)
-{
- int _tmp;
- __asm__ __volatile__ ("cli %0;\n\t"
- "csync;\n\t"
- "sti %0;\n\t"
- :"=d"(_tmp):);
-}
-#elif !defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
-static inline void CSYNC (void)
-{
- __asm__ __volatile__ ("nop; nop; nop;\n\t"
- "ssync;\n\t"
- ::);
-}
-#elif !defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
-static inline void CSYNC (void)
-{
- __asm__ __volatile__ ("csync;\n\t");
+ if (ANOMALY_05000312 && ANOMALY_05000244)
+ __asm__ __volatile__(
+ "cli %0;"
+ "nop;"
+ "nop;"
+ "csync;"
+ "sti %0;"
+ : "=d" (_tmp)
+ );
+ else if (ANOMALY_05000312 && !ANOMALY_05000244)
+ __asm__ __volatile__(
+ "cli %0;"
+ "csync;"
+ "sti %0;"
+ : "=d" (_tmp)
+ );
+ else if (!ANOMALY_05000312 && ANOMALY_05000244)
+ __asm__ __volatile__(
+ "nop;"
+ "nop;"
+ "nop;"
+ "ssync;"
+ );
+ else
+ __asm__ __volatile__("csync;");
}
-#endif
#else /* __ASSEMBLY__ */
#define ssync(x) SSYNC(x)
#define csync(x) CSYNC(x)
-#if defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
+#if ANOMALY_05000312 && ANOMALY_05000244
#define SSYNC(scratch) cli scratch; nop; nop; SSYNC; sti scratch;
#define CSYNC(scratch) cli scratch; nop; nop; CSYNC; sti scratch;
-#elif defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
+#elif ANOMALY_05000312 && !ANOMALY_05000244
#define SSYNC(scratch) cli scratch; nop; nop; SSYNC; sti scratch;
#define CSYNC(scratch) cli scratch; nop; nop; CSYNC; sti scratch;
-#elif !defined(ANOMALY_05000312) && defined(ANOMALY_05000244)
+#elif !ANOMALY_05000312 && ANOMALY_05000244
#define SSYNC(scratch) nop; nop; nop; SSYNC;
#define CSYNC(scratch) nop; nop; nop; CSYNC;
-#elif !defined(ANOMALY_05000312) && !defined(ANOMALY_05000244)
+#elif !ANOMALY_05000312 && !ANOMALY_05000244
#define SSYNC(scratch) SSYNC;
#define CSYNC(scratch) CSYNC;
*/
/* This file shoule be up to date with:
- * - Revision U, May 17, 2006; ADSP-BF533 Blackfin Processor Anomaly List
- * - Revision Y, May 17, 2006; ADSP-BF532 Blackfin Processor Anomaly List
- * - Revision T, May 17, 2006; ADSP-BF531 Blackfin Processor Anomaly List
+ * - Revision X, March 23, 2007; ADSP-BF533 Blackfin Processor Anomaly List
+ * - Revision AB, March 23, 2007; ADSP-BF532 Blackfin Processor Anomaly List
+ * - Revision W, March 23, 2007; ADSP-BF531 Blackfin Processor Anomaly List
*/
#ifndef _MACH_ANOMALY_H_
#define _MACH_ANOMALY_H_
/* We do not support 0.1 or 0.2 silicon - sorry */
-#if (defined(CONFIG_BF_REV_0_1) || defined(CONFIG_BF_REV_0_2))
-#error Kernel will not work on BF533 Version 0.1 or 0.2
+#if __SILICON_REVISION__ < 3
+# error Kernel will not work on BF533 silicon version 0.0, 0.1, or 0.2
#endif
-/* Issues that are common to 0.5, 0.4, and 0.3 silicon */
-#if (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_4) \
- || defined(CONFIG_BF_REV_0_3))
-#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
- * slot1 and store of a P register in slot 2 is not
- * supported */
-#define ANOMALY_05000105 /* Watchpoint Status Register (WPSTAT) bits are set on
- * every corresponding match */
-#define ANOMALY_05000119 /* DMA_RUN bit is not valid after a Peripheral Receive
- * Channel DMA stops */
-#define ANOMALY_05000122 /* Rx.H can not be used to access 16-bit System MMR
- * registers. */
-#define ANOMALY_05000166 /* PPI Data Lengths Between 8 and 16 do not zero out
- * upper bits*/
-#define ANOMALY_05000167 /* Turning Serial Ports on With External Frame Syncs */
-#define ANOMALY_05000180 /* PPI_DELAY not functional in PPI modes with 0 frame
- * syncs */
-#define ANOMALY_05000208 /* VSTAT status bit in PLL_STAT register is not
- * functional */
-#define ANOMALY_05000219 /* NMI event at boot time results in unpredictable
- * state */
-#define ANOMALY_05000229 /* SPI Slave Boot Mode modifies registers */
-#define ANOMALY_05000272 /* Certain data cache write through modes fail for
- * VDDint <=0.9V */
-#define ANOMALY_05000273 /* Writes to Synchronous SDRAM memory may be lost */
-#define ANOMALY_05000277 /* Writes to a flag data register one SCLK cycle after
- * an edge is detected may clear interrupt */
-#define ANOMALY_05000278 /* Disabling Peripherals with DMA running may cause
- * DMA system instability */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is
- * not restored */
-#define ANOMALY_05000282 /* Memory DMA corruption with 32-bit data and traffic
- * control */
-#define ANOMALY_05000283 /* A system MMR write is stalled indefinitely when
- * killed in a particular stage*/
-#define ANOMALY_05000311 /* Erroneous flag pin operations under specific
- * sequences */
-#define ANOMALY_05000312 /* Errors when SSYNC, CSYNC, or loads to LT, LB and LC
- * registers are interrupted */
-#define ANOMALY_05000313 /* PPI Is Level-Sensitive on First Transfer */
-#define ANOMALY_05000315 /* Killed System MMR Write Completes Erroneously On
- * Next System MMR Access */
-#define ANOMALY_05000319 /* Internal Voltage Regulator Values of 1.05V, 1.10V
- * and 1.15V Not Allowed for LQFP Packages */
-#endif /* Issues that are common to 0.5, 0.4, and 0.3 silicon */
+#if defined(__ADSPBF531__)
+# define ANOMALY_BF531 1
+#else
+# define ANOMALY_BF531 0
+#endif
+#if defined(__ADSPBF532__)
+# define ANOMALY_BF532 1
+#else
+# define ANOMALY_BF532 0
+#endif
+#if defined(__ADSPBF533__)
+# define ANOMALY_BF533 1
+#else
+# define ANOMALY_BF533 0
+#endif
-/* These issues only occur on 0.3 or 0.4 BF533 */
-#if (defined(CONFIG_BF_REV_0_4) || defined(CONFIG_BF_REV_0_3))
-#define ANOMALY_05000099 /* UART Line Status Register (UART_LSR) bits are not
- * updated at the same time. */
-#define ANOMALY_05000158 /* Boot fails when data cache enabled: Data from a Data
- * Cache Fill can be corrupted after or during
- * Instruction DMA if certain core stalls exist */
-#define ANOMALY_05000179 /* PPI_COUNT cannot be programmed to 0 in General
- * Purpose TX or RX modes */
-#define ANOMALY_05000198 /* Failing SYSTEM MMR accesses when stalled by
- * preceding memory read */
-#define ANOMALY_05000200 /* SPORT TFS and DT are incorrectly driven during
- * inactive channels in certain conditions */
-#define ANOMALY_05000202 /* Possible infinite stall with specific dual dag
- * situation */
-#define ANOMALY_05000215 /* UART TX Interrupt masked erroneously */
-#define ANOMALY_05000225 /* Incorrect pulse-width of UART start-bit */
-#define ANOMALY_05000227 /* Scratchpad memory bank reads may return incorrect
- * data*/
-#define ANOMALY_05000230 /* UART Receiver is less robust against Baudrate
- * Differences in certain Conditions */
-#define ANOMALY_05000231 /* UART STB bit incorrectly affects receiver setting */
-#define ANOMALY_05000242 /* DF bit in PLL_CTL register does not respond to
- * hardware reset */
-#define ANOMALY_05000244 /* With instruction cache enabled, a CSYNC or SSYNC or
- * IDLE around a Change of Control causes
- * unpredictable results */
-#define ANOMALY_05000245 /* Spurious Hardware Error from an access in the
- * shadow of a conditional branch */
-#define ANOMALY_05000246 /* Data CPLB's should prevent spurious hardware
- * errors */
-#define ANOMALY_05000253 /* Maximum external clock speed for Timers */
-#define ANOMALY_05000255 /* Entering Hibernate Mode with RTC Seconds event
- * interrupt not functional */
-#define ANOMALY_05000257 /* An interrupt or exception during short Hardware
- * loops may cause the instruction fetch unit to
- * malfunction */
-#define ANOMALY_05000258 /* Instruction Cache is corrupted when bit 9 and 12 of
- * the ICPLB Data registers differ */
-#define ANOMALY_05000260 /* ICPLB_STATUS MMR register may be corrupted */
-#define ANOMALY_05000261 /* DCPLB_FAULT_ADDR MMR register may be corrupted */
-#define ANOMALY_05000262 /* Stores to data cache may be lost */
-#define ANOMALY_05000263 /* Hardware loop corrupted when taking an ICPLB exception */
-#define ANOMALY_05000264 /* A Sync instruction (CSYNC, SSYNC) or an IDLE
- * instruction will cause an infinite stall in the
- * second to last instruction in a hardware loop */
-#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on
- * SPORT external receive and transmit clocks. */
-#define ANOMALY_05000269 /* High I/O activity causes the output voltage of the
- * internal voltage regulator (VDDint) to increase. */
-#define ANOMALY_05000270 /* High I/O activity causes the output voltage of the
- * internal voltage regulator (VDDint) to decrease */
-#endif /* issues only occur on 0.3 or 0.4 BF533 */
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot 2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* UART Line Status Register (UART_LSR) Bits Are Not Updated at the Same Time */
+#define ANOMALY_05000099 (__SILICON_REVISION__ < 5)
+/* Watchpoint Status Register (WPSTAT) Bits Are Set on Every Corresponding Match */
+#define ANOMALY_05000105 (1)
+/* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */
+#define ANOMALY_05000119 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* Instruction DMA Can Cause Data Cache Fills to Fail (Boot Implications) */
+#define ANOMALY_05000158 (__SILICON_REVISION__ < 5)
+/* PPI Data Lengths Between 8 and 16 Do Not Zero Out Upper Bits */
+#define ANOMALY_05000166 (1)
+/* Turning Serial Ports on with External Frame Syncs */
+#define ANOMALY_05000167 (1)
+/* PPI_COUNT Cannot Be Programmed to 0 in General Purpose TX or RX Modes */
+#define ANOMALY_05000179 (__SILICON_REVISION__ < 5)
+/* PPI_DELAY Not Functional in PPI Modes with 0 Frame Syncs */
+#define ANOMALY_05000180 (1)
+/* Timer Pin Limitations for PPI TX Modes with External Frame Syncs */
+#define ANOMALY_05000183 (__SILICON_REVISION__ < 4)
+/* False Protection Exceptions */
+#define ANOMALY_05000189 (__SILICON_REVISION__ < 4)
+/* False I/O Pin Interrupts on Edge-Sensitive Inputs When Polarity Setting Is Changed */
+#define ANOMALY_05000193 (__SILICON_REVISION__ < 4)
+/* Restarting SPORT in Specific Modes May Cause Data Corruption */
+#define ANOMALY_05000194 (__SILICON_REVISION__ < 4)
+/* Failing MMR Accesses When Stalled by Preceding Memory Read */
+#define ANOMALY_05000198 (__SILICON_REVISION__ < 5)
+/* Current DMA Address Shows Wrong Value During Carry Fix */
+#define ANOMALY_05000199 (__SILICON_REVISION__ < 4)
+/* SPORT TFS and DT Are Incorrectly Driven During Inactive Channels in Certain Conditions */
+#define ANOMALY_05000200 (__SILICON_REVISION__ < 5)
+/* Receive Frame Sync Not Ignored During Active Frames in SPORT Multi-Channel Mode */
+#define ANOMALY_05000201 (__SILICON_REVISION__ < 4)
+/* Possible Infinite Stall with Specific Dual-DAG Situation */
+#define ANOMALY_05000202 (__SILICON_REVISION__ < 5)
+/* Specific Sequence That Can Cause DMA Error or DMA Stopping */
+#define ANOMALY_05000203 (__SILICON_REVISION__ < 4)
+/* Incorrect data read with write-through cache and allocate cache lines on reads only mode */
+#define ANOMALY_05000204 (__SILICON_REVISION__ < 4 && ANOMALY_BF533)
+/* Recovery from "Brown-Out" Condition */
+#define ANOMALY_05000207 (__SILICON_REVISION__ < 4)
+/* VSTAT Status Bit in PLL_STAT Register Is Not Functional */
+#define ANOMALY_05000208 (1)
+/* Speed Path in Computational Unit Affects Certain Instructions */
+#define ANOMALY_05000209 (__SILICON_REVISION__ < 4)
+/* UART TX Interrupt Masked Erroneously */
+#define ANOMALY_05000215 (__SILICON_REVISION__ < 5)
+/* NMI Event at Boot Time Results in Unpredictable State */
+#define ANOMALY_05000219 (1)
+/* Incorrect Pulse-Width of UART Start Bit */
+#define ANOMALY_05000225 (__SILICON_REVISION__ < 5)
+/* Scratchpad Memory Bank Reads May Return Incorrect Data */
+#define ANOMALY_05000227 (__SILICON_REVISION__ < 5)
+/* SPI Slave Boot Mode Modifies Registers from Reset Value */
+#define ANOMALY_05000229 (1)
+/* UART Receiver is Less Robust Against Baudrate Differences in Certain Conditions */
+#define ANOMALY_05000230 (__SILICON_REVISION__ < 5)
+/* UART STB Bit Incorrectly Affects Receiver Setting */
+#define ANOMALY_05000231 (__SILICON_REVISION__ < 5)
+/* PPI_FS3 Is Not Driven in 2 or 3 Internal Frame Sync Transmit Modes */
+#define ANOMALY_05000233 (__SILICON_REVISION__ < 4)
+/* Incorrect Revision Number in DSPID Register */
+#define ANOMALY_05000234 (__SILICON_REVISION__ == 4)
+/* DF Bit in PLL_CTL Register Does Not Respond to Hardware Reset */
+#define ANOMALY_05000242 (__SILICON_REVISION__ < 4)
+/* If I-Cache Is On, CSYNC/SSYNC/IDLE Around Change of Control Causes Failures */
+#define ANOMALY_05000244 (__SILICON_REVISION__ < 5)
+/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (1)
+/* Data CPLBs Should Prevent Spurious Hardware Errors */
+#define ANOMALY_05000246 (__SILICON_REVISION__ < 5)
+/* Incorrect Bit Shift of Data Word in Multichannel (TDM) Mode in Certain Conditions */
+#define ANOMALY_05000250 (__SILICON_REVISION__ == 4)
+/* Maximum External Clock Speed for Timers */
+#define ANOMALY_05000253 (__SILICON_REVISION__ < 5)
+/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT Mode with External Clock */
+#define ANOMALY_05000254 (__SILICON_REVISION__ > 4)
+/* Entering Hibernate State with RTC Seconds Interrupt Not Functional */
+#define ANOMALY_05000255 (__SILICON_REVISION__ < 5)
+/* Interrupt/Exception During Short Hardware Loop May Cause Bad Instruction Fetches */
+#define ANOMALY_05000257 (__SILICON_REVISION__ < 5)
+/* Instruction Cache Is Corrupted When Bits 9 and 12 of the ICPLB Data Registers Differ */
+#define ANOMALY_05000258 (__SILICON_REVISION__ < 5)
+/* ICPLB_STATUS MMR Register May Be Corrupted */
+#define ANOMALY_05000260 (__SILICON_REVISION__ < 5)
+/* DCPLB_FAULT_ADDR MMR Register May Be Corrupted */
+#define ANOMALY_05000261 (__SILICON_REVISION__ < 5)
+/* Stores To Data Cache May Be Lost */
+#define ANOMALY_05000262 (__SILICON_REVISION__ < 5)
+/* Hardware Loop Corrupted When Taking an ICPLB Exception */
+#define ANOMALY_05000263 (__SILICON_REVISION__ < 5)
+/* CSYNC/SSYNC/IDLE Causes Infinite Stall in Penultimate Instruction in Hardware Loop */
+#define ANOMALY_05000264 (__SILICON_REVISION__ < 5)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (__SILICON_REVISION__ < 5)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Increase */
+#define ANOMALY_05000269 (__SILICON_REVISION__ < 5)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Decrease */
+#define ANOMALY_05000270 (__SILICON_REVISION__ < 5)
+/* Spontaneous Reset of Internal Voltage Regulator */
+#define ANOMALY_05000271 (__SILICON_REVISION__ < 4)
+/* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */
+#define ANOMALY_05000272 (1)
+/* Writes to Synchronous SDRAM Memory May Be Lost */
+#define ANOMALY_05000273 (1)
+/* Timing Requirements Change for External Frame Sync PPI Modes with Non-Zero PPI_DELAY */
+#define ANOMALY_05000276 (1)
+/* Writes to an I/O Data Register One SCLK Cycle after an Edge Is Detected May Clear Interrupt */
+#define ANOMALY_05000277 (1)
+/* Disabling Peripherals with DMA Running May Cause DMA System Instability */
+#define ANOMALY_05000278 (1)
+/* False Hardware Error Exception When ISR Context Is Not Restored */
+#define ANOMALY_05000281 (1)
+/* Memory DMA Corruption with 32-Bit Data and Traffic Control */
+#define ANOMALY_05000282 (1)
+/* System MMR Write Is Stalled Indefinitely When Killed in a Particular Stage */
+#define ANOMALY_05000283 (1)
+/* SPORTs May Receive Bad Data If FIFOs Fill Up */
+#define ANOMALY_05000288 (1)
+/* Memory-To-Memory DMA Source/Destination Descriptors Must Be in Same Memory Space */
+#define ANOMALY_05000301 (1)
+/* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */
+#define ANOMALY_05000302 (__SILICON_REVISION__ < 5)
+/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+#define ANOMALY_05000305 (__SILICON_REVISION__ < 5)
+/* New Feature: Additional PPI Frame Sync Sampling Options (Not Available On Older Silicon) */
+#define ANOMALY_05000306 (__SILICON_REVISION__ < 5)
+/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
+#define ANOMALY_05000310 (1)
+/* Erroneous Flag (GPIO) Pin Operations under Specific Sequences */
+#define ANOMALY_05000311 (1)
+/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */
+#define ANOMALY_05000312 (1)
+/* PPI Is Level-Sensitive on First Transfer */
+#define ANOMALY_05000313 (1)
+/* Killed System MMR Write Completes Erroneously On Next System MMR Access */
+#define ANOMALY_05000315 (1)
+/* Internal Voltage Regulator Values of 1.05V, 1.10V and 1.15V Not Allowed for LQFP Packages */
+#define ANOMALY_05000319 (ANOMALY_BF531 || ANOMALY_BF532)
-/* These issues are only on 0.4 silicon */
-#if (defined(CONFIG_BF_REV_0_4))
-#define ANOMALY_05000234 /* Incorrect Revision Number in DSPID Register */
-#define ANOMALY_05000250 /* Incorrect Bit-Shift of Data Word in Multichannel
- * (TDM) */
-#endif /* issues are only on 0.4 silicon */
+/* These anomalies have been "phased" out of analog.com anomaly sheets and are
+ * here to show running on older silicon just isn't feasible.
+ */
-/* These issues are only on 0.3 silicon */
-#if defined(CONFIG_BF_REV_0_3)
-#define ANOMALY_05000183 /* Timer Pin limitations for PPI TX Modes with
- * External Frame Syncs */
-#define ANOMALY_05000189 /* False Protection Exceptions caused by Speculative
- * Instruction or Data Fetches, or by Fetches at the
- * boundary of reserved memory space */
-#define ANOMALY_05000193 /* False Flag Pin Interrupts on Edge Sensitive Inputs
- * when polarity setting is changed */
-#define ANOMALY_05000194 /* Sport Restarting in specific modes may cause data
- * corruption */
-#define ANOMALY_05000199 /* DMA current address shows wrong value during carry
- * fix */
-#define ANOMALY_05000201 /* Receive frame sync not ignored during active
- * frames in sport MCM */
-#define ANOMALY_05000203 /* Specific sequence that can cause DMA error or DMA
- * stopping */
-#if defined(CONFIG_BF533)
-#define ANOMALY_05000204 /* Incorrect data read with write-through cache and
- * allocate cache lines on reads only mode */
-#endif /* CONFIG_BF533 */
-#define ANOMALY_05000207 /* Recovery from "brown-out" condition */
-#define ANOMALY_05000209 /* Speed-Path in computational unit affects certain
- * instructions */
-#define ANOMALY_05000233 /* PPI_FS3 is not driven in 2 or 3 internal Frame
- * Sync Transmit Mode */
-#define ANOMALY_05000271 /* Spontaneous reset of Internal Voltage Regulator */
-#endif /* only on 0.3 silicon */
+/* Watchpoints (Hardware Breakpoints) are not supported */
+#define ANOMALY_05000067 (__SILICON_REVISION__ < 3)
+/* Reserved bits in SYSCFG register not set at power on */
+#define ANOMALY_05000109 (__SILICON_REVISION__ < 3)
+/* Trace Buffers may record discontinuities into emulation mode and/or exception, NMI, reset handlers */
+#define ANOMALY_05000116 (__SILICON_REVISION__ < 3)
+/* DTEST_COMMAND initiated memory access may be incorrect if data cache or DMA is active */
+#define ANOMALY_05000123 (__SILICON_REVISION__ < 3)
+/* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1, or 1:1 */
+#define ANOMALY_05000124 (__SILICON_REVISION__ < 3)
+/* Erroneous exception when enabling cache */
+#define ANOMALY_05000125 (__SILICON_REVISION__ < 3)
+/* SPI clock polarity and phase bits incorrect during booting */
+#define ANOMALY_05000126 (__SILICON_REVISION__ < 3)
+/* DMEM_CONTROL is not set on Reset */
+#define ANOMALY_05000137 (__SILICON_REVISION__ < 3)
+/* SPI boot will not complete if there is a zero fill block in the loader file */
+#define ANOMALY_05000138 (__SILICON_REVISION__ < 3)
+/* Allowing the SPORT RX FIFO to fill will cause an overflow */
+#define ANOMALY_05000140 (__SILICON_REVISION__ < 3)
+/* An Infinite Stall occurs with a particular sequence of consecutive dual dag events */
+#define ANOMALY_05000141 (__SILICON_REVISION__ < 3)
+/* Interrupts may be lost when a programmable input flag is configured to be edge sensitive */
+#define ANOMALY_05000142 (__SILICON_REVISION__ < 3)
+/* A read from external memory may return a wrong value with data cache enabled */
+#define ANOMALY_05000143 (__SILICON_REVISION__ < 3)
+/* DMA and TESTSET conflict when both are accessing external memory */
+#define ANOMALY_05000144 (__SILICON_REVISION__ < 3)
+/* In PWM_OUT mode, you must enable the PPI block to generate a waveform from PPI_CLK */
+#define ANOMALY_05000145 (__SILICON_REVISION__ < 3)
+/* MDMA may lose the first few words of a descriptor chain */
+#define ANOMALY_05000146 (__SILICON_REVISION__ < 3)
+/* The source MDMA descriptor may stop with a DMA Error */
+#define ANOMALY_05000147 (__SILICON_REVISION__ < 3)
+/* When booting from a 16-bit asynchronous memory device, the upper 8-bits of each word must be 0x00 */
+#define ANOMALY_05000148 (__SILICON_REVISION__ < 3)
+/* Frame Delay in SPORT Multichannel Mode */
+#define ANOMALY_05000153 (__SILICON_REVISION__ < 3)
+/* SPORT TFS signal is active in Multi-channel mode outside of valid channels */
+#define ANOMALY_05000154 (__SILICON_REVISION__ < 3)
+/* Timer1 can not be used for PWMOUT mode when a certain PPI mode is in use */
+#define ANOMALY_05000155 (__SILICON_REVISION__ < 3)
+/* A killed 32-bit System MMR write will lead to the next system MMR access thinking it should be 32-bit. */
+#define ANOMALY_05000157 (__SILICON_REVISION__ < 3)
+/* SPORT transmit data is not gated by external frame sync in certain conditions */
+#define ANOMALY_05000163 (__SILICON_REVISION__ < 3)
+/* SDRAM auto-refresh and subsequent Power Ups */
+#define ANOMALY_05000168 (__SILICON_REVISION__ < 3)
+/* DATA CPLB page miss can result in lost write-through cache data writes */
+#define ANOMALY_05000169 (__SILICON_REVISION__ < 3)
+/* DMA vs Core accesses to external memory */
+#define ANOMALY_05000173 (__SILICON_REVISION__ < 3)
+/* Cache Fill Buffer Data lost */
+#define ANOMALY_05000174 (__SILICON_REVISION__ < 3)
+/* Overlapping Sequencer and Memory Stalls */
+#define ANOMALY_05000175 (__SILICON_REVISION__ < 3)
+/* Multiplication of (-1) by (-1) followed by an accumulator saturation */
+#define ANOMALY_05000176 (__SILICON_REVISION__ < 3)
+/* Disabling the PPI resets the PPI configuration registers */
+#define ANOMALY_05000181 (__SILICON_REVISION__ < 3)
+/* PPI TX Mode with 2 External Frame Syncs */
+#define ANOMALY_05000185 (__SILICON_REVISION__ < 3)
+/* PPI does not invert the Driving PPICLK edge in Transmit Modes */
+#define ANOMALY_05000191 (__SILICON_REVISION__ < 3)
+/* In PPI Transmit Modes with External Frame Syncs POLC */
+#define ANOMALY_05000192 (__SILICON_REVISION__ < 3)
+/* Internal Voltage Regulator may not start up */
+#define ANOMALY_05000206 (__SILICON_REVISION__ < 3)
-#if defined(CONFIG_BF_REV_0_2)
-#define ANOMALY_05000067 /* Watchpoints (Hardware Breakpoints) are not
- * supported */
-#define ANOMALY_05000109 /* Reserved bits in SYSCFG register not set at
- * power on */
-#define ANOMALY_05000116 /* Trace Buffers may record discontinuities into
- * emulation mode and/or exception, NMI, reset
- * handlers */
-#define ANOMALY_05000123 /* DTEST_COMMAND initiated memory access may be
- * incorrect if data cache or DMA is active */
-#define ANOMALY_05000124 /* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1,
- * or 1:1 */
-#define ANOMALY_05000125 /* Erroneous exception when enabling cache */
-#define ANOMALY_05000126 /* SPI clock polarity and phase bits incorrect
- * during booting */
-#define ANOMALY_05000137 /* DMEM_CONTROL is not set on Reset */
-#define ANOMALY_05000138 /* SPI boot will not complete if there is a zero fill
- * block in the loader file */
-#define ANOMALY_05000140 /* Allowing the SPORT RX FIFO to fill will cause an
- * overflow */
-#define ANOMALY_05000141 /* An Infinite Stall occurs with a particular sequence
- * of consecutive dual dag events */
-#define ANOMALY_05000142 /* Interrupts may be lost when a programmable input
- * flag is configured to be edge sensitive */
-#define ANOMALY_05000143 /* A read from external memory may return a wrong
- * value with data cache enabled */
-#define ANOMALY_05000144 /* DMA and TESTSET conflict when both are accessing
- * external memory */
-#define ANOMALY_05000145 /* In PWM_OUT mode, you must enable the PPI block to
- * generate a waveform from PPI_CLK */
-#define ANOMALY_05000146 /* MDMA may lose the first few words of a descriptor
- * chain */
-#define ANOMALY_05000147 /* The source MDMA descriptor may stop with a DMA
- * Error */
-#define ANOMALY_05000148 /* When booting from a 16-bit asynchronous memory
- * device, the upper 8-bits of each word must be
- * 0x00 */
-#define ANOMALY_05000153 /* Frame Delay in SPORT Multichannel Mode */
-#define ANOMALY_05000154 /* SPORT TFS signal is active in Multi-channel mode
- * outside of valid channels */
-#define ANOMALY_05000155 /* Timer1 can not be used for PWMOUT mode when a
- * certain PPI mode is in use */
-#define ANOMALY_05000157 /* A killed 32-bit System MMR write will lead to
- * the next system MMR access thinking it should be
- * 32-bit. */
-#define ANOMALY_05000163 /* SPORT transmit data is not gated by external frame
- * sync in certain conditions */
-#define ANOMALY_05000168 /* SDRAM auto-refresh and subsequent Power Ups */
-#define ANOMALY_05000169 /* DATA CPLB page miss can result in lost
- * write-through cache data writes */
-#define ANOMALY_05000173 /* DMA vs Core accesses to external memory */
-#define ANOMALY_05000174 /* Cache Fill Buffer Data lost */
-#define ANOMALY_05000175 /* Overlapping Sequencer and Memory Stalls */
-#define ANOMALY_05000176 /* Multiplication of (-1) by (-1) followed by an
- * accumulator saturation */
-#define ANOMALY_05000181 /* Disabling the PPI resets the PPI configuration
- * registers */
-#define ANOMALY_05000185 /* PPI TX Mode with 2 External Frame Syncs */
-#define ANOMALY_05000191 /* PPI does not invert the Driving PPICLK edge in
- * Transmit Modes */
-#define ANOMALY_05000192 /* In PPI Transmit Modes with External Frame Syncs
- * POLC */
-#define ANOMALY_05000206 /* Internal Voltage Regulator may not start up */
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000266 (0)
#endif
-
-#endif /* _MACH_ANOMALY_H_ */
#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
#endif
-#if defined(ANOMALY_05000273) && (CONFIG_CCLK_DIV == 1)
+#if ANOMALY_05000273 && (CONFIG_CCLK_DIV == 1)
#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
#endif
*/
/* This file shoule be up to date with:
- * - Revision J, June 1, 2006; ADSP-BF537 Blackfin Processor Anomaly List
- * - Revision I, June 1, 2006; ADSP-BF536 Blackfin Processor Anomaly List
- * - Revision J, June 1, 2006; ADSP-BF534 Blackfin Processor Anomaly List
+ * - Revision M, March 13, 2007; ADSP-BF537 Blackfin Processor Anomaly List
+ * - Revision L, March 13, 2007; ADSP-BF536 Blackfin Processor Anomaly List
+ * - Revision M, March 13, 2007; ADSP-BF534 Blackfin Processor Anomaly List
*/
#ifndef _MACH_ANOMALY_H_
#define _MACH_ANOMALY_H_
/* We do not support 0.1 silicon - sorry */
-#if (defined(CONFIG_BF_REV_0_1))
-#error Kernel will not work on BF537/6/4 Version 0.1
+#if __SILICON_REVISION__ < 2
+# error Kernel will not work on BF537 silicon version 0.0 or 0.1
#endif
-#if (defined(CONFIG_BF_REV_0_3) || defined(CONFIG_BF_REV_0_2))
-#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
- * slot1 and store of a P register in slot 2 is not
- * supported */
-#define ANOMALY_05000119 /* DMA_RUN bit is not valid after a Peripheral Receive
- * Channel DMA stops */
-#define ANOMALY_05000122 /* Rx.H can not be used to access 16-bit System MMR
- * registers. */
-#define ANOMALY_05000166 /* PPI Data Lengths Between 8 and 16 do not zero out
- * upper bits*/
-#define ANOMALY_05000180 /* PPI_DELAY not functional in PPI modes with 0 frame
- * syncs */
-#if (defined(CONFIG_BF537) || defined(CONFIG_BF536))
-#define ANOMALY_05000247 /* CLKIN Buffer Output Enable Reset Behavior Is
- * Changed */
+#if defined(__ADSPBF534__)
+# define ANOMALY_BF534 1
+#else
+# define ANOMALY_BF534 0
#endif
-#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on
- * SPORT external receive and transmit clocks. */
-#define ANOMALY_05000272 /* Certain data cache write through modes fail for
- * VDDint <=0.9V */
-#define ANOMALY_05000273 /* Writes to Synchronous SDRAM memory may be lost */
-#define ANOMALY_05000277 /* Writes to a flag data register one SCLK cycle after
- * an edge is detected may clear interrupt */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is
- * not restored */
-#define ANOMALY_05000282 /* Memory DMA corruption with 32-bit data and traffic
- * control */
-#define ANOMALY_05000283 /* A system MMR write is stalled indefinitely when
- * killed in a particular stage*/
-#define ANOMALY_05000310 /* False hardware errors caused by fetches at the
- * boundary of reserved memory */
-#define ANOMALY_05000312 /* Errors when SSYNC, CSYNC, or loads to LT, LB and LC
- * registers are interrupted */
-#define ANOMALY_05000313 /* PPI is level sensitive on first transfer */
-#define ANOMALY_05000322 /* EMAC RMII mode at 10-Base-T speed: RX frames not
- * received properly */
+#if defined(__ADSPBF536__)
+# define ANOMALY_BF536 1
+#else
+# define ANOMALY_BF536 0
#endif
-
-#if defined(CONFIG_BF_REV_0_2)
-#define ANOMALY_05000244 /* With instruction cache enabled, a CSYNC or SSYNC or
- * IDLE around a Change of Control causes
- * unpredictable results */
-#define ANOMALY_05000250 /* Incorrect Bit-Shift of Data Word in Multichannel
- * (TDM) */
-#if (defined(CONFIG_BF537) || defined(CONFIG_BF536))
-#define ANOMALY_05000252 /* EMAC Tx DMA error after an early frame abort */
-#endif
-#define ANOMALY_05000253 /* Maximum external clock speed for Timers */
-#define ANOMALY_05000255 /* Entering Hibernate Mode with RTC Seconds event
- * interrupt not functional */
-#if (defined(CONFIG_BF537) || defined(CONFIG_BF536))
-#define ANOMALY_05000256 /* EMAC MDIO input latched on wrong MDC edge */
+#if defined(__ADSPBF537__)
+# define ANOMALY_BF537 1
+#else
+# define ANOMALY_BF537 0
#endif
-#define ANOMALY_05000257 /* An interrupt or exception during short Hardware
- * loops may cause the instruction fetch unit to
- * malfunction */
-#define ANOMALY_05000258 /* Instruction Cache is corrupted when bit 9 and 12 of
- * the ICPLB Data registers differ */
-#define ANOMALY_05000260 /* ICPLB_STATUS MMR register may be corrupted */
-#define ANOMALY_05000261 /* DCPLB_FAULT_ADDR MMR register may be corrupted */
-#define ANOMALY_05000262 /* Stores to data cache may be lost */
-#define ANOMALY_05000263 /* Hardware loop corrupted when taking an ICPLB exception */
-#define ANOMALY_05000264 /* A Sync instruction (CSYNC, SSYNC) or an IDLE
- * instruction will cause an infinite stall in the
- * second to last instruction in a hardware loop */
-#define ANOMALY_05000268 /* Memory DMA error when peripheral DMA is running
- * and non-zero DEB_TRAFFIC_PERIOD value */
-#define ANOMALY_05000270 /* High I/O activity causes the output voltage of the
- * internal voltage regulator (VDDint) to decrease */
-#define ANOMALY_05000277 /* Writes to a flag data register one SCLK cycle after
- * an edge is detected may clear interrupt */
-#define ANOMALY_05000278 /* Disabling Peripherals with DMA running may cause
- * DMA system instability */
-#define ANOMALY_05000280 /* SPI Master boot mode does not work well with
- * Atmel Dataflash devices */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context
- * is not restored */
-#define ANOMALY_05000282 /* Memory DMA corruption with 32-bit data and traffic
- * control */
-#define ANOMALY_05000283 /* System MMR Write Is Stalled Indefinitely When
- * Killed in a Particular Stage */
-#define ANOMALY_05000285 /* New Feature: EMAC TX DMA Word Alignment
- * (Not Available On Older Silicon) */
-#define ANOMALY_05000288 /* SPORTs may receive bad data if FIFOs fill up */
-#define ANOMALY_05000315 /* Killed System MMR Write Completes Erroneously
- * On Next System MMR Access */
-#define ANOMALY_05000316 /* EMAC RMII mode: collisions occur in Full Duplex
- * mode */
-#define ANOMALY_05000321 /* EMAC RMII mode: TX frames in half duplex fail with
- * status No Carrier */
-#endif /* CONFIG_BF_REV_0_2 */
-#endif /* _MACH_ANOMALY_H_ */
+/* Multi-issue instruction with dsp32shiftimm in slot1 and P-reg store in slot 2 not supported */
+#define ANOMALY_05000074 (1)
+/* DMA_RUN bit is not valid after a Peripheral Receive Channel DMA stops */
+#define ANOMALY_05000119 (1)
+/* Rx.H cannot be used to access 16-bit System MMR registers */
+#define ANOMALY_05000122 (1)
+/* Killed 32-bit MMR write leads to next system MMR access thinking it should be 32-bit */
+#define ANOMALY_05000157 (__SILICON_REVISION__ < 2)
+/* PPI Data Lengths Between 8 and 16 do not zero out upper bits*/
+#define ANOMALY_05000166 (1) /* XXX: deleted from BF537 sheet ? */
+/* PPI_DELAY not functional in PPI modes with 0 frame syncs */
+#define ANOMALY_05000180 (1)
+/* Instruction Cache Is Not Functional */
+#define ANOMALY_05000237 (__SILICON_REVISION__ < 2)
+/* If i-cache is on, CSYNC/SSYNC/IDLE around Change of Control causes failures */
+#define ANOMALY_05000244 (__SILICON_REVISION__ < 3)
+/* Spurious Hardware Error from an access in the shadow of a conditional branch */
+#define ANOMALY_05000245 (1)
+/* CLKIN Buffer Output Enable Reset Behavior Is Changed */
+#define ANOMALY_05000247 (1)
+/* Incorrect Bit-Shift of Data Word in Multichannel (TDM) mode in certain conditions */
+#define ANOMALY_05000250 (__SILICON_REVISION__ < 3)
+/* EMAC Tx DMA error after an early frame abort */
+#define ANOMALY_05000252 (__SILICON_REVISION__ < 3)
+/* Maximum external clock speed for Timers */
+#define ANOMALY_05000253 (__SILICON_REVISION__ < 3)
+/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT mode with external clock */
+#define ANOMALY_05000254 (__SILICON_REVISION__ > 2)
+/* Entering Hibernate Mode with RTC Seconds event interrupt not functional */
+#define ANOMALY_05000255 (__SILICON_REVISION__ < 3)
+/* EMAC MDIO input latched on wrong MDC edge */
+#define ANOMALY_05000256 (__SILICON_REVISION__ < 3)
+/* Interrupt/Exception during short hardware loop may cause bad instruction fetches */
+#define ANOMALY_05000257 (__SILICON_REVISION__ < 3)
+/* Instruction Cache is corrupted when bits 9 and 12 of the ICPLB Data registers differ */
+#define ANOMALY_05000258 (((ANOMALY_BF536 || ANOMALY_BF537) && __SILICON_REVISION__ == 1) || __SILICON_REVISION__ == 2)
+/* ICPLB_STATUS MMR register may be corrupted */
+#define ANOMALY_05000260 (__SILICON_REVISION__ == 2)
+/* DCPLB_FAULT_ADDR MMR register may be corrupted */
+#define ANOMALY_05000261 (__SILICON_REVISION__ < 3)
+/* Stores to data cache may be lost */
+#define ANOMALY_05000262 (__SILICON_REVISION__ < 3)
+/* Hardware loop corrupted when taking an ICPLB exception */
+#define ANOMALY_05000263 (__SILICON_REVISION__ == 2)
+/* CSYNC/SSYNC/IDLE causes infinite stall in second to last instruction in hardware loop */
+#define ANOMALY_05000264 (__SILICON_REVISION__ < 3)
+/* Sensitivity to noise with slow input edge rates on external SPORT TX and RX clocks */
+#define ANOMALY_05000265 (1)
+/* Memory DMA error when peripheral DMA is running with non-zero DEB_TRAFFIC_PERIOD */
+#define ANOMALY_05000268 (__SILICON_REVISION__ < 3)
+/* High I/O activity causes output voltage of internal voltage regulator (VDDint) to decrease */
+#define ANOMALY_05000270 (__SILICON_REVISION__ < 3)
+/* Certain data cache write through modes fail for VDDint <=0.9V */
+#define ANOMALY_05000272 (1)
+/* Writes to Synchronous SDRAM memory may be lost */
+#define ANOMALY_05000273 (__SILICON_REVISION__ < 3)
+/* Writes to an I/O data register one SCLK cycle after an edge is detected may clear interrupt */
+#define ANOMALY_05000277 (__SILICON_REVISION__ < 3)
+/* Disabling Peripherals with DMA running may cause DMA system instability */
+#define ANOMALY_05000278 (((ANOMALY_BF536 || ANOMALY_BF537) && __SILICON_REVISION__ < 3) || (ANOMALY_BF534 && __SILICON_REVISION__ < 2))
+/* SPI Master boot mode does not work well with Atmel Data flash devices */
+#define ANOMALY_05000280 (1)
+/* False Hardware Error Exception when ISR context is not restored */
+#define ANOMALY_05000281 (__SILICON_REVISION__ < 3)
+/* Memory DMA corruption with 32-bit data and traffic control */
+#define ANOMALY_05000282 (__SILICON_REVISION__ < 3)
+/* System MMR Write Is Stalled Indefinitely When Killed in a Particular Stage */
+#define ANOMALY_05000283 (__SILICON_REVISION__ < 3)
+/* New Feature: EMAC TX DMA Word Alignment (Not Available On Older Silicon) */
+#define ANOMALY_05000285 (__SILICON_REVISION__ < 3)
+/* SPORTs may receive bad data if FIFOs fill up */
+#define ANOMALY_05000288 (__SILICON_REVISION__ < 3)
+/* Memory to memory DMA source/destination descriptors must be in same memory space */
+#define ANOMALY_05000301 (1)
+/* SSYNCs After Writes To CAN/DMA MMR Registers Are Not Always Handled Correctly */
+#define ANOMALY_05000304 (__SILICON_REVISION__ < 3)
+/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+#define ANOMALY_05000305 (__SILICON_REVISION__ < 3)
+/* SCKELOW Bit Does Not Maintain State Through Hibernate */
+#define ANOMALY_05000307 (__SILICON_REVISION__ < 3)
+/* Writing UART_THR while UART clock is disabled sends erroneous start bit */
+#define ANOMALY_05000309 (__SILICON_REVISION__ < 3)
+/* False hardware errors caused by fetches at the boundary of reserved memory */
+#define ANOMALY_05000310 (1)
+/* Errors when SSYNC, CSYNC, or loads to LT, LB and LC registers are interrupted */
+#define ANOMALY_05000312 (1)
+/* PPI is level sensitive on first transfer */
+#define ANOMALY_05000313 (1)
+/* Killed System MMR Write Completes Erroneously On Next System MMR Access */
+#define ANOMALY_05000315 (__SILICON_REVISION__ < 3)
+/* EMAC RMII mode: collisions occur in Full Duplex mode */
+#define ANOMALY_05000316 (__SILICON_REVISION__ < 3)
+/* EMAC RMII mode: TX frames in half duplex fail with status No Carrier */
+#define ANOMALY_05000321 (__SILICON_REVISION__ < 3)
+/* EMAC RMII mode at 10-Base-T speed: RX frames not received properly */
+#define ANOMALY_05000322 (1)
+
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000125 (0)
+#define ANOMALY_05000183 (0)
+#define ANOMALY_05000198 (0)
+#define ANOMALY_05000266 (0)
+#define ANOMALY_05000311 (0)
+
+#endif
#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
#endif
-#if defined(ANOMALY_05000273) && (CONFIG_CCLK_DIV == 1)
+#if ANOMALY_05000273 && (CONFIG_CCLK_DIV == 1)
#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
#endif
* Licensed under the GPL-2 or later.
*/
+/* This file shoule be up to date with:
+ * - Revision B, April 6, 2007; ADSP-BF549 Silicon Anomaly List
+ */
+
#ifndef _MACH_ANOMALY_H_
#define _MACH_ANOMALY_H_
-#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
- * slot1 and store of a P register in slot 2 is not
- * supported */
-#define ANOMALY_05000119 /* DMA_RUN bit is not valid after a Peripheral Receive
- * Channel DMA stops */
-#define ANOMALY_05000122 /* Rx.H can not be used to access 16-bit System MMR
- * registers. */
-#define ANOMALY_05000245 /* Spurious Hardware Error from an Access in the
- * Shadow of a Conditional Branch */
-#define ANOMALY_05000255 /* Entering Hibernate Mode with RTC Seconds event
- * interrupt not functional */
-#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on
- * SPORT external receive and transmit clocks. */
-#define ANOMALY_05000272 /* Certain data cache write through modes fail for
- * VDDint <=0.9V */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is
- * not restored */
-#define ANOMALY_05000310 /* False Hardware Errors Caused by Fetches at the
- * Boundary of Reserved Memory */
-#define ANOMALY_05000312 /* Errors When SSYNC, CSYNC, or Loads to LT, LB and
- * LC Registers Are Interrupted */
-#define ANOMALY_05000324 /* TWI Slave Boot Mode Is Not Functional */
-#define ANOMALY_05000325 /* External FIFO Boot Mode Is Not Functional */
-#define ANOMALY_05000327 /* Data Lost When Core and DMA Accesses Are Made to
- * the USB FIFO Simultaneously */
-#define ANOMALY_05000328 /* Incorrect Access of OTP_STATUS During otp_write()
- * function */
-#define ANOMALY_05000329 /* Synchronous Burst Flash Boot Mode Is Not Functional
- * */
-#define ANOMALY_05000330 /* Host DMA Boot Mode Is Not Functional */
-#define ANOMALY_05000334 /* Inadequate Timing Margins on DDR DQS to DQ and DQM
- * Skew */
-#define ANOMALY_05000335 /* Inadequate Rotary Debounce Logic Duration */
-#define ANOMALY_05000336 /* Phantom Interrupt Occurs After First Configuration
- * of Host DMA Port */
-#define ANOMALY_05000337 /* Disallowed Configuration Prevents Subsequent
- * Allowed Configuration on Host DMA Port */
-#define ANOMALY_05000338 /* Slave-Mode SPI0 MISO Failure With CPHA = 0 */
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot 2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */
+#define ANOMALY_05000119 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (1)
+/* Entering Hibernate State with RTC Seconds Interrupt Not Functional */
+#define ANOMALY_05000255 (1)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (1)
+/* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */
+#define ANOMALY_05000272 (1)
+/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
+#define ANOMALY_05000310 (1)
+/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */
+#define ANOMALY_05000312 (1)
+/* TWI Slave Boot Mode Is Not Functional */
+#define ANOMALY_05000324 (1)
+/* External FIFO Boot Mode Is Not Functional */
+#define ANOMALY_05000325 (1)
+/* Data Lost When Core and DMA Accesses Are Made to the USB FIFO Simultaneously */
+#define ANOMALY_05000327 (1)
+/* Incorrect Access of OTP_STATUS During otp_write() Function */
+#define ANOMALY_05000328 (1)
+/* Synchronous Burst Flash Boot Mode Is Not Functional */
+#define ANOMALY_05000329 (1)
+/* Host DMA Boot Mode Is Not Functional */
+#define ANOMALY_05000330 (1)
+/* Inadequate Timing Margins on DDR DQS to DQ and DQM Skew */
+#define ANOMALY_05000334 (1)
+/* Inadequate Rotary Debounce Logic Duration */
+#define ANOMALY_05000335 (1)
+/* Phantom Interrupt Occurs After First Configuration of Host DMA Port */
+#define ANOMALY_05000336 (1)
+/* Disallowed Configuration Prevents Subsequent Allowed Configuration on Host DMA Port */
+#define ANOMALY_05000337 (1)
+/* Slave-Mode SPI0 MISO Failure With CPHA = 0 */
+#define ANOMALY_05000338 (1)
+
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000125 (0)
+#define ANOMALY_05000183 (0)
+#define ANOMALY_05000198 (0)
+#define ANOMALY_05000244 (0)
+#define ANOMALY_05000263 (0)
+#define ANOMALY_05000266 (0)
+#define ANOMALY_05000273 (0)
+#define ANOMALY_05000311 (0)
-#endif /* _MACH_ANOMALY_H_ */
+#endif
*/
/* This file shoule be up to date with:
- * - Revision L, Aug 10, 2006; ADSP-BF561 Silicon Anomaly List
+ * - Revision N, March 28, 2007; ADSP-BF561 Silicon Anomaly List
*/
#ifndef _MACH_ANOMALY_H_
#define _MACH_ANOMALY_H_
-/* We do not support 0.1 or 0.4 silicon - sorry */
-#if (defined(CONFIG_BF_REV_0_1) || defined(CONFIG_BF_REV_0_2) || defined(CONFIG_BF_REV_0_4))
-#error Kernel will not work on BF561 Version 0.1, 0.2, or 0.4
+/* We do not support 0.1, 0.2, or 0.4 silicon - sorry */
+#if __SILICON_REVISION__ < 3 || __SILICON_REVISION__ == 4
+# error Kernel will not work on BF561 silicon version 0.0, 0.1, 0.2, or 0.4
#endif
-/* Issues that are common to 0.5 and 0.3 silicon */
-#if (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_3))
-#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
- * slot1 and store of a P register in slot 2 is not
- * supported */
-#define ANOMALY_05000099 /* UART Line Status Register (UART_LSR) bits are not
- * updated at the same time. */
-#define ANOMALY_05000120 /* Testset instructions restricted to 32-bit aligned
- * memory locations */
-#define ANOMALY_05000122 /* Rx.H cannot be used to access 16-bit System MMR
- * registers */
-#define ANOMALY_05000127 /* Signbits instruction not functional under certain
- * conditions */
-#define ANOMALY_05000149 /* IMDMA S1/D1 channel may stall */
-#define ANOMALY_05000166 /* PPI Data Lengths Between 8 and 16 do not zero out
- * upper bits */
-#define ANOMALY_05000167 /* Turning Serial Ports on With External Frame Syncs */
-#define ANOMALY_05000180 /* PPI_DELAY not functional in PPI modes with 0 frame
- * syncs */
-#define ANOMALY_05000182 /* IMDMA does not operate to full speed for 600MHz
- * and higher devices */
-#define ANOMALY_05000187 /* IMDMA Corrupted Data after a Halt */
-#define ANOMALY_05000190 /* PPI not functional at core voltage < 1Volt */
-#define ANOMALY_05000208 /* VSTAT status bit in PLL_STAT register is not
- * functional */
-#define ANOMALY_05000245 /* Spurious Hardware Error from an access in the
- * shadow of a conditional branch */
-#define ANOMALY_05000257 /* Interrupt/Exception during short hardware loop
- * may cause bad instruction fetches */
-#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on
- * external SPORT TX and RX clocks */
-#define ANOMALY_05000267 /* IMDMA may corrupt data under certain conditions */
-#define ANOMALY_05000269 /* High I/O activity causes output voltage of internal
- * voltage regulator (VDDint) to increase */
-#define ANOMALY_05000270 /* High I/O activity causes output voltage of internal
- * voltage regulator (VDDint) to decrease */
-#define ANOMALY_05000272 /* Certain data cache write through modes fail for
- * VDDint <=0.9V */
-#define ANOMALY_05000274 /* Data cache write back to external synchronous memory
- * may be lost */
-#define ANOMALY_05000275 /* PPI Timing and sampling informaton updates */
-#define ANOMALY_05000312 /* Errors when SSYNC, CSYNC, or loads to LT, LB and LC
- * registers are interrupted */
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot 2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* UART Line Status Register (UART_LSR) Bits Are Not Updated at the Same Time */
+#define ANOMALY_05000099 (__SILICON_REVISION__ < 5)
+/* Trace Buffers may contain errors in emulation mode and/or exception, NMI, reset handlers */
+#define ANOMALY_05000116 (__SILICON_REVISION__ < 3)
+/* Testset instructions restricted to 32-bit aligned memory locations */
+#define ANOMALY_05000120 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* Erroneous exception when enabling cache */
+#define ANOMALY_05000125 (__SILICON_REVISION__ < 3)
+/* Signbits instruction not functional under certain conditions */
+#define ANOMALY_05000127 (1)
+/* Two bits in the Watchpoint Status Register (WPSTAT) are swapped */
+#define ANOMALY_05000134 (__SILICON_REVISION__ < 3)
+/* Enable wires from the Data Watchpoint Address Control Register (WPDACTL) are swapped */
+#define ANOMALY_05000135 (__SILICON_REVISION__ < 3)
+/* Stall in multi-unit DMA operations */
+#define ANOMALY_05000136 (__SILICON_REVISION__ < 3)
+/* Allowing the SPORT RX FIFO to fill will cause an overflow */
+#define ANOMALY_05000140 (__SILICON_REVISION__ < 3)
+/* Infinite Stall may occur with a particular sequence of consecutive dual dag events */
+#define ANOMALY_05000141 (__SILICON_REVISION__ < 3)
+/* Interrupts may be lost when a programmable input flag is configured to be edge sensitive */
+#define ANOMALY_05000142 (__SILICON_REVISION__ < 3)
+/* DMA and TESTSET conflict when both are accessing external memory */
+#define ANOMALY_05000144 (__SILICON_REVISION__ < 3)
+/* In PWM_OUT mode, you must enable the PPI block to generate a waveform from PPI_CLK */
+#define ANOMALY_05000145 (__SILICON_REVISION__ < 3)
+/* MDMA may lose the first few words of a descriptor chain */
+#define ANOMALY_05000146 (__SILICON_REVISION__ < 3)
+/* Source MDMA descriptor may stop with a DMA Error near beginning of descriptor fetch */
+#define ANOMALY_05000147 (__SILICON_REVISION__ < 3)
+/* IMDMA S1/D1 channel may stall */
+#define ANOMALY_05000149 (1)
+/* DMA engine may lose data due to incorrect handshaking */
+#define ANOMALY_05000150 (__SILICON_REVISION__ < 3)
+/* DMA stalls when all three controllers read data from the same source */
+#define ANOMALY_05000151 (__SILICON_REVISION__ < 3)
+/* Execution stall when executing in L2 and doing external accesses */
+#define ANOMALY_05000152 (__SILICON_REVISION__ < 3)
+/* Frame Delay in SPORT Multichannel Mode */
+#define ANOMALY_05000153 (__SILICON_REVISION__ < 3)
+/* SPORT TFS signal stays active in multichannel mode outside of valid channels */
+#define ANOMALY_05000154 (__SILICON_REVISION__ < 3)
+/* Timers in PWM-Out Mode with PPI GP Receive (Input) Mode with 0 Frame Syncs */
+#define ANOMALY_05000156 (__SILICON_REVISION__ < 4)
+/* Killed 32-bit MMR write leads to next system MMR access thinking it should be 32-bit */
+#define ANOMALY_05000157 (__SILICON_REVISION__ < 3)
+/* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1, or 1:1 */
+#define ANOMALY_05000159 (__SILICON_REVISION__ < 3)
+/* A read from external memory may return a wrong value with data cache enabled */
+#define ANOMALY_05000160 (__SILICON_REVISION__ < 3)
+/* Data Cache Fill data can be corrupted after/during Instruction DMA if certain core stalls exist */
+#define ANOMALY_05000161 (__SILICON_REVISION__ < 3)
+/* DMEM_CONTROL<12> is not set on Reset */
+#define ANOMALY_05000162 (__SILICON_REVISION__ < 3)
+/* SPORT transmit data is not gated by external frame sync in certain conditions */
+#define ANOMALY_05000163 (__SILICON_REVISION__ < 3)
+/* PPI Data Lengths Between 8 and 16 Do Not Zero Out Upper Bits */
+#define ANOMALY_05000166 (1)
+/* Turning Serial Ports on with External Frame Syncs */
+#define ANOMALY_05000167 (1)
+/* SDRAM auto-refresh and subsequent Power Ups */
+#define ANOMALY_05000168 (__SILICON_REVISION__ < 5)
+/* DATA CPLB page miss can result in lost write-through cache data writes */
+#define ANOMALY_05000169 (__SILICON_REVISION__ < 5)
+/* Boot-ROM code modifies SICA_IWRx wakeup registers */
+#define ANOMALY_05000171 (__SILICON_REVISION__ < 5)
+/* DSPID register values incorrect */
+#define ANOMALY_05000172 (__SILICON_REVISION__ < 3)
+/* DMA vs Core accesses to external memory */
+#define ANOMALY_05000173 (__SILICON_REVISION__ < 3)
+/* Cache Fill Buffer Data lost */
+#define ANOMALY_05000174 (__SILICON_REVISION__ < 5)
+/* Overlapping Sequencer and Memory Stalls */
+#define ANOMALY_05000175 (__SILICON_REVISION__ < 5)
+/* Multiplication of (-1) by (-1) followed by an accumulator saturation */
+#define ANOMALY_05000176 (__SILICON_REVISION__ < 5)
+/* PPI_COUNT Cannot Be Programmed to 0 in General Purpose TX or RX Modes */
+#define ANOMALY_05000179 (__SILICON_REVISION__ < 5)
+/* PPI_DELAY Not Functional in PPI Modes with 0 Frame Syncs */
+#define ANOMALY_05000180 (1)
+/* Disabling the PPI resets the PPI configuration registers */
+#define ANOMALY_05000181 (__SILICON_REVISION__ < 5)
+/* IMDMA does not operate to full speed for 600MHz and higher devices */
+#define ANOMALY_05000182 (1)
+/* Timer Pin limitations for PPI TX Modes with External Frame Syncs */
+#define ANOMALY_05000184 (__SILICON_REVISION__ < 5)
+/* PPI TX Mode with 2 External Frame Syncs */
+#define ANOMALY_05000185 (__SILICON_REVISION__ < 5)
+/* PPI packing with Data Length greater than 8 bits (not a meaningful mode) */
+#define ANOMALY_05000186 (__SILICON_REVISION__ < 5)
+/* IMDMA Corrupted Data after a Halt */
+#define ANOMALY_05000187 (1)
+/* IMDMA Restrictions on Descriptor and Buffer Placement in Memory */
+#define ANOMALY_05000188 (__SILICON_REVISION__ < 5)
+/* False Protection Exceptions */
+#define ANOMALY_05000189 (__SILICON_REVISION__ < 5)
+/* PPI not functional at core voltage < 1Volt */
+#define ANOMALY_05000190 (1)
+/* PPI does not invert the Driving PPICLK edge in Transmit Modes */
+#define ANOMALY_05000191 (__SILICON_REVISION__ < 3)
+/* False I/O Pin Interrupts on Edge-Sensitive Inputs When Polarity Setting Is Changed */
+#define ANOMALY_05000193 (__SILICON_REVISION__ < 5)
+/* Restarting SPORT in Specific Modes May Cause Data Corruption */
+#define ANOMALY_05000194 (__SILICON_REVISION__ < 5)
+/* Failing MMR Accesses When Stalled by Preceding Memory Read */
+#define ANOMALY_05000198 (__SILICON_REVISION__ < 5)
+/* Current DMA Address Shows Wrong Value During Carry Fix */
+#define ANOMALY_05000199 (__SILICON_REVISION__ < 5)
+/* SPORT TFS and DT Are Incorrectly Driven During Inactive Channels in Certain Conditions */
+#define ANOMALY_05000200 (__SILICON_REVISION__ < 5)
+/* Possible Infinite Stall with Specific Dual-DAG Situation */
+#define ANOMALY_05000202 (__SILICON_REVISION__ < 5)
+/* Incorrect data read with write-through cache and allocate cache lines on reads only mode */
+#define ANOMALY_05000204 (__SILICON_REVISION__ < 5)
+/* Specific sequence that can cause DMA error or DMA stopping */
+#define ANOMALY_05000205 (__SILICON_REVISION__ < 5)
+/* Recovery from "Brown-Out" Condition */
+#define ANOMALY_05000207 (__SILICON_REVISION__ < 5)
+/* VSTAT Status Bit in PLL_STAT Register Is Not Functional */
+#define ANOMALY_05000208 (1)
+/* Speed Path in Computational Unit Affects Certain Instructions */
+#define ANOMALY_05000209 (__SILICON_REVISION__ < 5)
+/* UART TX Interrupt Masked Erroneously */
+#define ANOMALY_05000215 (__SILICON_REVISION__ < 5)
+/* NMI Event at Boot Time Results in Unpredictable State */
+#define ANOMALY_05000219 (__SILICON_REVISION__ < 5)
+/* Data Corruption with Cached External Memory and Non-Cached On-Chip L2 Memory */
+#define ANOMALY_05000220 (__SILICON_REVISION__ < 5)
+/* Incorrect Pulse-Width of UART Start Bit */
+#define ANOMALY_05000225 (__SILICON_REVISION__ < 5)
+/* Scratchpad Memory Bank Reads May Return Incorrect Data */
+#define ANOMALY_05000227 (__SILICON_REVISION__ < 5)
+/* UART Receiver is Less Robust Against Baudrate Differences in Certain Conditions */
+#define ANOMALY_05000230 (__SILICON_REVISION__ < 5)
+/* UART STB Bit Incorrectly Affects Receiver Setting */
+#define ANOMALY_05000231 (__SILICON_REVISION__ < 5)
+/* SPORT data transmit lines are incorrectly driven in multichannel mode */
+#define ANOMALY_05000232 (__SILICON_REVISION__ < 5)
+/* DF Bit in PLL_CTL Register Does Not Respond to Hardware Reset */
+#define ANOMALY_05000242 (__SILICON_REVISION__ < 5)
+/* If I-Cache Is On, CSYNC/SSYNC/IDLE Around Change of Control Causes Failures */
+#define ANOMALY_05000244 (__SILICON_REVISION__ < 5)
+/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (__SILICON_REVISION__ < 5)
+/* TESTSET operation forces stall on the other core */
+#define ANOMALY_05000248 (__SILICON_REVISION__ < 5)
+/* Incorrect Bit Shift of Data Word in Multichannel (TDM) Mode in Certain Conditions */
+#define ANOMALY_05000250 (__SILICON_REVISION__ > 2 && __SILICON_REVISION__ < 5)
+/* Exception Not Generated for MMR Accesses in Reserved Region */
+#define ANOMALY_05000251 (__SILICON_REVISION__ < 5)
+/* Maximum External Clock Speed for Timers */
+#define ANOMALY_05000253 (__SILICON_REVISION__ < 5)
+/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT Mode with External Clock */
+#define ANOMALY_05000254 (__SILICON_REVISION__ > 3)
+/* Interrupt/Exception During Short Hardware Loop May Cause Bad Instruction Fetches */
+#define ANOMALY_05000257 (__SILICON_REVISION__ < 5)
+/* Instruction Cache Is Corrupted When Bits 9 and 12 of the ICPLB Data Registers Differ */
+#define ANOMALY_05000258 (__SILICON_REVISION__ < 5)
+/* ICPLB_STATUS MMR Register May Be Corrupted */
+#define ANOMALY_05000260 (__SILICON_REVISION__ < 5)
+/* DCPLB_FAULT_ADDR MMR Register May Be Corrupted */
+#define ANOMALY_05000261 (__SILICON_REVISION__ < 5)
+/* Stores To Data Cache May Be Lost */
+#define ANOMALY_05000262 (__SILICON_REVISION__ < 5)
+/* Hardware Loop Corrupted When Taking an ICPLB Exception */
+#define ANOMALY_05000263 (__SILICON_REVISION__ < 5)
+/* CSYNC/SSYNC/IDLE Causes Infinite Stall in Penultimate Instruction in Hardware Loop */
+#define ANOMALY_05000264 (__SILICON_REVISION__ < 5)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (__SILICON_REVISION__ < 5)
+/* IMDMA destination IRQ status must be read prior to using IMDMA */
+#define ANOMALY_05000266 (__SILICON_REVISION__ > 3)
+/* IMDMA may corrupt data under certain conditions */
+#define ANOMALY_05000267 (1)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Increase */
+#define ANOMALY_05000269 (1)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Decrease */
+#define ANOMALY_05000270 (1)
+/* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */
+#define ANOMALY_05000272 (1)
+/* Data cache write back to external synchronous memory may be lost */
+#define ANOMALY_05000274 (1)
+/* PPI Timing and Sampling Information Updates */
+#define ANOMALY_05000275 (__SILICON_REVISION__ > 2)
+/* Timing Requirements Change for External Frame Sync PPI Modes with Non-Zero PPI_DELAY */
+#define ANOMALY_05000276 (__SILICON_REVISION__ < 5)
+/* Disabling Peripherals with DMA Running May Cause DMA System Instability */
+#define ANOMALY_05000278 (__SILICON_REVISION__ < 5)
+/* False Hardware Error Exception When ISR Context Is Not Restored */
+#define ANOMALY_05000281 (__SILICON_REVISION__ < 5)
+/* System MMR Write Is Stalled Indefinitely When Killed in a Particular Stage */
+#define ANOMALY_05000283 (1)
+/* A read will receive incorrect data under certain conditions */
+#define ANOMALY_05000287 (__SILICON_REVISION__ < 5)
+/* SPORTs May Receive Bad Data If FIFOs Fill Up */
+#define ANOMALY_05000288 (__SILICON_REVISION__ < 5)
+/* Memory-To-Memory DMA Source/Destination Descriptors Must Be in Same Memory Space */
+#define ANOMALY_05000301 (1)
+/* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */
+#define ANOMALY_05000302 (1)
+/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+#define ANOMALY_05000305 (__SILICON_REVISION__ < 5)
+/* SCKELOW Bit Does Not Maintain State Through Hibernate */
+#define ANOMALY_05000307 (__SILICON_REVISION__ < 5)
+/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
+#define ANOMALY_05000310 (1)
+/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */
+#define ANOMALY_05000312 (1)
+/* PPI Is Level-Sensitive on First Transfer */
+#define ANOMALY_05000313 (1)
+/* Killed System MMR Write Completes Erroneously On Next System MMR Access */
+#define ANOMALY_05000315 (1)
+/* PF2 Output Remains Asserted After SPI Master Boot */
+#define ANOMALY_05000320 (__SILICON_REVISION__ > 3)
+/* Erroneous GPIO Flag Pin Operations Under Specific Sequences */
+#define ANOMALY_05000323 (1)
+/* SPORT Secondary Receive Channel Not Functional When Word Length Exceeds 16 Bits */
+#define ANOMALY_05000326 (__SILICON_REVISION__ > 3)
+/* New Feature: 24-Bit SPI Boot Mode Support (Not Available On Older Silicon) */
+#define ANOMALY_05000331 (__SILICON_REVISION__ < 5)
+/* New Feature: Slave SPI Boot Mode Supported (Not Available On Older Silicon) */
+#define ANOMALY_05000332 (__SILICON_REVISION__ < 5)
+/* Flag Data Register Writes One SCLK Cycle After Edge Is Detected May Clear Interrupt Status */
+#define ANOMALY_05000333 (__SILICON_REVISION__ < 5)
-#endif /* (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_3)) */
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000183 (0)
+#define ANOMALY_05000273 (0)
+#define ANOMALY_05000311 (0)
-#if (defined(CONFIG_BF_REV_0_5))
-#define ANOMALY_05000254 /* Incorrect Timer Pulse Width in Single-Shot PWM_OUT
- * mode with external clock */
-#define ANOMALY_05000266 /* IMDMA destination IRQ status must be read prior to
- * using IMDMA */
#endif
-
-#if (defined(CONFIG_BF_REV_0_3))
-#define ANOMALY_05000156 /* Timers in PWM-Out Mode with PPI GP Receive (Input)
- * Mode with 0 Frame Syncs */
-#define ANOMALY_05000168 /* SDRAM auto-refresh and subsequent Power Ups */
-#define ANOMALY_05000169 /* DATA CPLB page miss can result in lost write-through
- * cache data writes */
-#define ANOMALY_05000171 /* Boot-ROM code modifies SICA_IWRx wakeup registers */
-#define ANOMALY_05000174 /* Cache Fill Buffer Data lost */
-#define ANOMALY_05000175 /* Overlapping Sequencer and Memory Stalls */
-#define ANOMALY_05000176 /* Multiplication of (-1) by (-1) followed by an
- * accumulator saturation */
-#define ANOMALY_05000179 /* PPI_COUNT cannot be programmed to 0 in General
- * Purpose TX or RX modes */
-#define ANOMALY_05000181 /* Disabling the PPI resets the PPI configuration
- * registers */
-#define ANOMALY_05000184 /* Timer Pin limitations for PPI TX Modes with
- * External Frame Syncs */
-#define ANOMALY_05000185 /* PPI TX Mode with 2 External Frame Syncs */
-#define ANOMALY_05000186 /* PPI packing with Data Length greater than 8 bits
- * (not a meaningful mode) */
-#define ANOMALY_05000188 /* IMDMA Restrictions on Descriptor and Buffer
- * Placement in Memory */
-#define ANOMALY_05000189 /* False Protection Exception */
-#define ANOMALY_05000193 /* False Flag Pin Interrupts on Edge Sensitive Inputs
- * when polarity setting is changed */
-#define ANOMALY_05000194 /* Restarting SPORT in specific modes may cause data
- * corruption */
-#define ANOMALY_05000198 /* Failing MMR accesses when stalled by preceding
- * memory read */
-#define ANOMALY_05000199 /* DMA current address shows wrong value during carry
- * fix */
-#define ANOMALY_05000200 /* SPORT TFS and DT are incorrectly driven during
- * inactive channels in certain conditions */
-#define ANOMALY_05000202 /* Possible infinite stall with specific dual-DAG
- * situation */
-#define ANOMALY_05000204 /* Incorrect data read with write-through cache and
- * allocate cache lines on reads only mode */
-#define ANOMALY_05000205 /* Specific sequence that can cause DMA error or DMA
- * stopping */
-#define ANOMALY_05000207 /* Recovery from "brown-out" condition */
-#define ANOMALY_05000209 /* Speed-Path in computational unit affects certain
- * instructions */
-#define ANOMALY_05000215 /* UART TX Interrupt masked erroneously */
-#define ANOMALY_05000219 /* NMI event at boot time results in unpredictable
- * state */
-#define ANOMALY_05000220 /* Data Corruption with Cached External Memory and
- * Non-Cached On-Chip L2 Memory */
-#define ANOMALY_05000225 /* Incorrect pulse-width of UART start-bit */
-#define ANOMALY_05000227 /* Scratchpad memory bank reads may return incorrect
- * data */
-#define ANOMALY_05000230 /* UART Receiver is less robust against Baudrate
- * Differences in certain Conditions */
-#define ANOMALY_05000231 /* UART STB bit incorrectly affects receiver setting */
-#define ANOMALY_05000232 /* SPORT data transmit lines are incorrectly driven in
- * multichannel mode */
-#define ANOMALY_05000242 /* DF bit in PLL_CTL register does not respond to
- * hardware reset */
-#define ANOMALY_05000244 /* If i-cache is on, CSYNC/SSYNC/IDLE around Change of
- * Control causes failures */
-#define ANOMALY_05000248 /* TESTSET operation forces stall on the other core */
-#define ANOMALY_05000250 /* Incorrect Bit-Shift of Data Word in Multichannel
- * (TDM) mode in certain conditions */
-#define ANOMALY_05000251 /* Exception not generated for MMR accesses in
- * reserved region */
-#define ANOMALY_05000253 /* Maximum external clock speed for Timers */
-#define ANOMALY_05000258 /* Instruction Cache is corrupted when bits 9 and 12
- * of the ICPLB Data registers differ */
-#define ANOMALY_05000260 /* ICPLB_STATUS MMR register may be corrupted */
-#define ANOMALY_05000261 /* DCPLB_FAULT_ADDR MMR register may be corrupted */
-#define ANOMALY_05000262 /* Stores to data cache may be lost */
-#define ANOMALY_05000263 /* Hardware loop corrupted when taking an ICPLB
- * exception */
-#define ANOMALY_05000264 /* CSYNC/SSYNC/IDLE causes infinite stall in second
- * to last instruction in hardware loop */
-#define ANOMALY_05000276 /* Timing requirements change for External Frame
- * Sync PPI Modes with non-zero PPI_DELAY */
-#define ANOMALY_05000278 /* Disabling Peripherals with DMA running may cause
- * DMA system instability */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is
- * not restored */
-#define ANOMALY_05000283 /* An MMR write is stalled indefinitely when killed
- * in a particular stage */
-#define ANOMALY_05000287 /* A read will receive incorrect data under certain
- * conditions */
-#define ANOMALY_05000288 /* SPORTs may receive bad data if FIFOs fill up */
-#endif
-
-#endif /* _MACH_ANOMALY_H_ */
#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
#endif
-#if defined(ANOMALY_05000273) && (CONFIG_CCLK_DIV == 1)
+#if ANOMALY_05000273 && (CONFIG_CCLK_DIV == 1)
#error ANOMALY 05000273, please make sure CCLK is at least 2x SCLK
#endif
#define bfin_read_SRAM_BASE_ADDRESS() bfin_read32(SRAM_BASE_ADDRESS)
#define bfin_write_SRAM_BASE_ADDRESS(val) bfin_write32(SRAM_BASE_ADDRESS,val)
#define bfin_read_DMEM_CONTROL() bfin_read32(DMEM_CONTROL)
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
extern void bfin_write_DMEM_CONTROL(unsigned int val);
#else
#define bfin_write_DMEM_CONTROL(val) bfin_write32(DMEM_CONTROL,val)
#define DTEST_DATA3 0xFFE0040C
*/
#define bfin_read_IMEM_CONTROL() bfin_read32(IMEM_CONTROL)
-#ifdef ANOMALY_05000125
+#if ANOMALY_05000125
extern void bfin_write_IMEM_CONTROL(unsigned int val);
#else
#define bfin_write_IMEM_CONTROL(val) bfin_write32(IMEM_CONTROL,val)
#include <asm/mach/anomaly.h>
-/*#if !defined(__ADSPLPBLACKFIN__)
-#warning def_LPBlackfin.h should only be included for 532 compatible chips.
-#endif
-*/
-
#define MK_BMSK_(x) (1<<x)
-#if defined(ANOMALY_05000198)
-
-#define bfin_read8(addr) ({ unsigned char __v; \
- __asm__ __volatile__ ("NOP;\n\t" \
- "%0 = b[%1] (z);\n\t" \
- : "=d"(__v) : "a"(addr)); \
- __v; })
-
-#define bfin_read16(addr) ({ unsigned __v; \
- __asm__ __volatile__ ("NOP;\n\t"\
- "%0 = w[%1] (z);\n\t"\
- : "=d"(__v) : "a"(addr)); (unsigned short)__v; })
-
-#define bfin_read32(addr) ({ unsigned __v; \
- __asm__ __volatile__ ("NOP;\n\t"\
- "%0 = [%1];\n\t"\
- : "=d"(__v) : "a"(addr)); __v; })
+#ifndef __ASSEMBLY__
-#define bfin_write8(addr, val) ({ \
- __asm__ __volatile__ ("NOP;\n\t" \
- "b[%0] = %1;\n\t" \
- : : "a"(addr), "d"(val) : "memory");})
-
-#define bfin_write16(addr,val) ({\
- __asm__ __volatile__ ("NOP;\n\t"\
- "w[%0] = %1;\n\t"\
- : : "a"(addr) , "d"(val) : "memory");})
-
-#define bfin_write32(addr,val) ({\
- __asm__ __volatile__ ("NOP;\n\t"\
- "[%0] = %1;\n\t"\
- : : "a"(addr) , "d"(val) : "memory");})
+#include <linux/types.h>
+#if ANOMALY_05000198
+# define NOP_PAD_ANOMALY_05000198 "nop;"
#else
-
-#define bfin_read8(addr) ({ unsigned char __v; \
- __asm__ __volatile__ ( \
- "%0 = b[%1] (z);\n\t" \
- :"=d"(__v) : "a"(addr)); \
- __v; })
-
-#define bfin_read16(addr) ({ unsigned __v; \
- __asm__ __volatile__ (\
- "%0 = w[%1] (z);\n\t"\
- : "=d"(__v) : "a"(addr)); (unsigned short)__v; })
-
-#define bfin_read32(addr) ({ unsigned __v; \
- __asm__ __volatile__ (\
- "%0 = [%1];\n\t"\
- : "=d"(__v) : "a"(addr)); __v; })
-
-#define bfin_write8(addr, val) ({ \
- __asm__ __volatile__ ( \
- "b[%0] = %1; \n\t" \
- ::"a"(addr), "d"(val) : "memory");})
-
-#define bfin_write16(addr,val) ({\
- __asm__ __volatile__ (\
- "w[%0] = %1;\n\t"\
- : : "a"(addr) , "d"(val) : "memory");})
-
-#define bfin_write32(addr,val) ({\
- __asm__ __volatile__ (\
- "[%0] = %1;\n\t"\
- : : "a"(addr) , "d"(val) : "memory");})
-
+# define NOP_PAD_ANOMALY_05000198
#endif
+#define bfin_read8(addr) ({ \
+ uint8_t __v; \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "%0 = b[%1] (z);" \
+ : "=d" (__v) \
+ : "a" (addr) \
+ ); \
+ __v; })
+
+#define bfin_read16(addr) ({ \
+ uint16_t __v; \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "%0 = w[%1] (z);" \
+ : "=d" (__v) \
+ : "a" (addr) \
+ ); \
+ __v; })
+
+#define bfin_read32(addr) ({ \
+ uint32_t __v; \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "%0 = [%1];" \
+ : "=d" (__v) \
+ : "a" (addr) \
+ ); \
+ __v; })
+
+#define bfin_write8(addr, val) \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "b[%0] = %1;" \
+ : \
+ : "a" (addr), "d" (val) \
+ : "memory" \
+ )
+
+#define bfin_write16(addr, val) \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "w[%0] = %1;" \
+ : \
+ : "a" (addr), "d" (val) \
+ : "memory" \
+ )
+
+#define bfin_write32(addr, val) \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000198 \
+ "[%0] = %1;" \
+ : \
+ : "a" (addr), "d" (val) \
+ : "memory" \
+ )
+
+#endif /* __ASSEMBLY__ */
+
/**************************************************
* System Register Bits
**************************************************/
#include <linux/linkage.h>
#include <linux/compiler.h>
+#include <asm/mach/anomaly.h>
/*
* Interrupt configuring macros.
extern unsigned long irq_flags;
-#define local_irq_enable() do { \
- __asm__ __volatile__ ( \
- "sti %0;" \
- ::"d"(irq_flags)); \
-} while (0)
+#define local_irq_enable() \
+ __asm__ __volatile__( \
+ "sti %0;" \
+ : \
+ : "d" (irq_flags) \
+ )
-#define local_irq_disable() do { \
- int _tmp_dummy; \
- __asm__ __volatile__ ( \
- "cli %0;" \
- :"=d" (_tmp_dummy):); \
-} while (0)
+#define local_irq_disable() \
+ do { \
+ int __tmp_dummy; \
+ __asm__ __volatile__( \
+ "cli %0;" \
+ : "=d" (__tmp_dummy) \
+ ); \
+ } while (0)
-#if defined(ANOMALY_05000244) && defined (CONFIG_BLKFIN_CACHE)
-#define idle_with_irq_disabled() do { \
- __asm__ __volatile__ ( \
- "nop; nop;\n" \
- ".align 8;\n" \
- "sti %0; idle;\n" \
- ::"d" (irq_flags)); \
-} while (0)
+#if ANOMALY_05000244 && defined(CONFIG_BLKFIN_CACHE)
+# define NOP_PAD_ANOMALY_05000244 "nop; nop;"
#else
-#define idle_with_irq_disabled() do { \
- __asm__ __volatile__ ( \
- ".align 8;\n" \
- "sti %0; idle;\n" \
- ::"d" (irq_flags)); \
-} while (0)
+# define NOP_PAD_ANOMALY_05000244
#endif
+#define idle_with_irq_disabled() \
+ __asm__ __volatile__( \
+ NOP_PAD_ANOMALY_05000244 \
+ ".align 8;" \
+ "sti %0;" \
+ "idle;" \
+ : \
+ : "d" (irq_flags) \
+ )
+
#ifdef CONFIG_DEBUG_HWERR
-#define __save_and_cli(x) do { \
- __asm__ __volatile__ ( \
- "cli %0;\n\tsti %1;" \
- :"=&d"(x): "d" (0x3F)); \
-} while (0)
+# define __save_and_cli(x) \
+ __asm__ __volatile__( \
+ "cli %0;" \
+ "sti %1;" \
+ : "=&d" (x) \
+ : "d" (0x3F) \
+ )
#else
-#define __save_and_cli(x) do { \
- __asm__ __volatile__ ( \
- "cli %0;" \
- :"=&d"(x):); \
-} while (0)
+# define __save_and_cli(x) \
+ __asm__ __volatile__( \
+ "cli %0;" \
+ : "=&d" (x) \
+ )
#endif
-#define local_save_flags(x) asm volatile ("cli %0;" \
- "sti %0;" \
- :"=d"(x):);
+#define local_save_flags(x) \
+ __asm__ __volatile__( \
+ "cli %0;" \
+ "sti %0;" \
+ : "=d" (x) \
+ )
#ifdef CONFIG_DEBUG_HWERR
#define irqs_enabled_from_flags(x) (((x) & ~0x3f) != 0)
#define irqs_enabled_from_flags(x) ((x) != 0x1f)
#endif
-#define local_irq_restore(x) do { \
- if (irqs_enabled_from_flags(x)) \
- local_irq_enable (); \
-} while (0)
+#define local_irq_restore(x) \
+ do { \
+ if (irqs_enabled_from_flags(x)) \
+ local_irq_enable(); \
+ } while (0)
/* For spinlocks etc */
#define local_irq_save(x) __save_and_cli(x)
git.openpandora.org / pandora-kernel.git / commitdiff