if (ah->ah_ee_version >= AR5K_EEPROM_VERSION_4_0) {
AR5K_EEPROM_READ_HDR(AR5K_EEPROM_MISC0, ee_misc0);
AR5K_EEPROM_READ_HDR(AR5K_EEPROM_MISC1, ee_misc1);
+
+ /* XXX: Don't know which versions include these two */
+ AR5K_EEPROM_READ_HDR(AR5K_EEPROM_MISC2, ee_misc2);
+
+ if (ee->ee_version >= AR5K_EEPROM_VERSION_4_3)
+ AR5K_EEPROM_READ_HDR(AR5K_EEPROM_MISC3, ee_misc3);
+
+ if (ee->ee_version >= AR5K_EEPROM_VERSION_5_0) {
+ AR5K_EEPROM_READ_HDR(AR5K_EEPROM_MISC4, ee_misc4);
+ AR5K_EEPROM_READ_HDR(AR5K_EEPROM_MISC5, ee_misc5);
+ AR5K_EEPROM_READ_HDR(AR5K_EEPROM_MISC6, ee_misc6);
+ }
}
if (ah->ah_ee_version < AR5K_EEPROM_VERSION_3_3) {
}
/*
- * Read supported modes from eeprom
+ * Read supported modes and some mode-specific calibration data
+ * from eeprom
*/
static int ath5k_eeprom_read_modes(struct ath5k_hw *ah, u32 *offset,
unsigned int mode)
if (ah->ah_ee_version < AR5K_EEPROM_VERSION_4_0)
goto done;
+ /* Note: >= v5 have bg freq piers on another location
+ * so these freq piers are ignored for >= v5 (should be 0xff
+ * anyway) */
switch(mode) {
case AR5K_EEPROM_MODE_11A:
if (ah->ah_ee_version < AR5K_EEPROM_VERSION_4_1)
return 0;
}
-
+/* Read mode-specific data (except power calibration data) */
static int
ath5k_eeprom_init_modes(struct ath5k_hw *ah)
{
return 0;
}
+/* Used to match PCDAC steps with power values on RF5111 chips
+ * (eeprom versions < 4). For RF5111 we have 10 pre-defined PCDAC
+ * steps that match with the power values we read from eeprom. On
+ * older eeprom versions (< 3.2) these steps are equaly spaced at
+ * 10% of the pcdac curve -until the curve reaches it's maximum-
+ * (10 steps from 0 to 100%) but on newer eeprom versions (>= 3.2)
+ * these 10 steps are spaced in a different way. This function returns
+ * the pcdac steps based on eeprom version and curve min/max so that we
+ * can have pcdac/pwr points.
+ */
static inline void
ath5k_get_pcdac_intercepts(struct ath5k_hw *ah, u8 min, u8 max, u8 *vp)
{
*vp++ = (ip[i] * max + (100 - ip[i]) * min) / 100;
}
+/* Read the frequency piers for each mode (mostly used on newer eeproms with 0xff
+ * frequency mask) */
static inline int
ath5k_eeprom_read_freq_list(struct ath5k_hw *ah, int *offset, int max,
- struct ath5k_chan_pcal_info *pc, u8 *count)
+ struct ath5k_chan_pcal_info *pc, unsigned int mode)
{
+ struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
int o = *offset;
int i = 0;
- u8 f1, f2;
+ u8 freq1, freq2;
int ret;
u16 val;
while(i < max) {
AR5K_EEPROM_READ(o++, val);
- f1 = (val >> 8) & 0xff;
- f2 = val & 0xff;
+ freq1 = (val >> 8) & 0xff;
+ freq2 = val & 0xff;
- if (f1)
- pc[i++].freq = f1;
+ if (freq1) {
+ pc[i++].freq = ath5k_eeprom_bin2freq(ee,
+ freq1, mode);
+ ee->ee_n_piers[mode]++;
+ }
- if (f2)
- pc[i++].freq = f2;
+ if (freq2) {
+ pc[i++].freq = ath5k_eeprom_bin2freq(ee,
+ freq2, mode);
+ ee->ee_n_piers[mode]++;
+ }
- if (!f1 || !f2)
+ if (!freq1 || !freq2)
break;
}
+
+ /* return new offset */
*offset = o;
- *count = i;
return 0;
}
+/* Read frequency piers for 802.11a */
static int
ath5k_eeprom_init_11a_pcal_freq(struct ath5k_hw *ah, int offset)
{
if (ee->ee_version >= AR5K_EEPROM_VERSION_3_3) {
ath5k_eeprom_read_freq_list(ah, &offset,
AR5K_EEPROM_N_5GHZ_CHAN, pcal,
- &ee->ee_n_piers[AR5K_EEPROM_MODE_11A]);
+ AR5K_EEPROM_MODE_11A);
} else {
mask = AR5K_EEPROM_FREQ_M(ah->ah_ee_version);
AR5K_EEPROM_READ(offset++, val);
pcal[9].freq |= (val >> 10) & 0x3f;
+
+ /* Fixed number of piers */
ee->ee_n_piers[AR5K_EEPROM_MODE_11A] = 10;
- }
- for(i = 0; i < AR5K_EEPROM_N_5GHZ_CHAN; i += 1) {
- pcal[i].freq = ath5k_eeprom_bin2freq(ee,
+ for (i = 0; i < AR5K_EEPROM_N_5GHZ_CHAN; i++) {
+ pcal[i].freq = ath5k_eeprom_bin2freq(ee,
pcal[i].freq, AR5K_EEPROM_MODE_11A);
+ }
}
return 0;
}
+/* Read frequency piers for 802.11bg on eeprom versions >= 5 and eemap >= 2 */
static inline int
ath5k_eeprom_init_11bg_2413(struct ath5k_hw *ah, unsigned int mode, int offset)
{
struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
struct ath5k_chan_pcal_info *pcal;
- int i;
switch(mode) {
case AR5K_EEPROM_MODE_11B:
ath5k_eeprom_read_freq_list(ah, &offset,
AR5K_EEPROM_N_2GHZ_CHAN_2413, pcal,
- &ee->ee_n_piers[mode]);
- for(i = 0; i < AR5K_EEPROM_N_2GHZ_CHAN_2413; i += 1) {
- pcal[i].freq = ath5k_eeprom_bin2freq(ee,
- pcal[i].freq, mode);
- }
+ mode);
return 0;
}
-
+/* Read power calibration for RF5111 chips
+ * For RF5111 we have an XPD -eXternal Power Detector- curve
+ * for each calibrated channel. Each curve has PCDAC steps on
+ * x axis and power on y axis and looks like a logarithmic
+ * function. To recreate the curve and pass the power values
+ * on the pcdac table, we read 10 points here and interpolate later.
+ */
static int
ath5k_eeprom_read_pcal_info_5111(struct ath5k_hw *ah, int mode)
{
return 0;
}
+/* Read power calibration for RF5112 chips
+ * For RF5112 we have 4 XPD -eXternal Power Detector- curves
+ * for each calibrated channel on 0, -6, -12 and -18dbm but we only
+ * use the higher (3) and the lower (0) curves. Each curve has PCDAC
+ * steps on x axis and power on y axis and looks like a linear
+ * function. To recreate the curve and pass the power values
+ * on the pcdac table, we read 4 points for xpd 0 and 3 points
+ * for xpd 3 here and interpolate later.
+ *
+ * Note: Many vendors just use xpd 0 so xpd 3 is zeroed.
+ */
static int
ath5k_eeprom_read_pcal_info_5112(struct ath5k_hw *ah, int mode)
{
/* PCDAC steps
* corresponding to the above power
- * measurements (static) */
+ * measurements (fixed) */
chan_pcal_info->pcdac_x3[0] = 20;
chan_pcal_info->pcdac_x3[1] = 35;
chan_pcal_info->pcdac_x3[2] = 63;
return 0;
}
+/* For RF2413 power calibration data doesn't start on a fixed location and
+ * if a mode is not supported, it's section is missing -not zeroed-.
+ * So we need to calculate the starting offset for each section by using
+ * these two functions */
+
+/* Return the size of each section based on the mode and the number of pd
+ * gains available (maximum 4). */
static inline unsigned int
ath5k_pdgains_size_2413(struct ath5k_eeprom_info *ee, unsigned int mode)
{
return sz;
}
+/* Return the starting offset for a section based on the modes supported
+ * and each section's size. */
static unsigned int
ath5k_cal_data_offset_2413(struct ath5k_eeprom_info *ee, int mode)
{
switch(mode) {
case AR5K_EEPROM_MODE_11G:
if (AR5K_EEPROM_HDR_11B(ee->ee_header))
- offset += ath5k_pdgains_size_2413(ee, AR5K_EEPROM_MODE_11B) + 2;
+ offset += ath5k_pdgains_size_2413(ee, AR5K_EEPROM_MODE_11B) +
+ AR5K_EEPROM_N_2GHZ_CHAN_2413 / 2;
/* fall through */
case AR5K_EEPROM_MODE_11B:
if (AR5K_EEPROM_HDR_11A(ee->ee_header))
- offset += ath5k_pdgains_size_2413(ee, AR5K_EEPROM_MODE_11A) + 5;
+ offset += ath5k_pdgains_size_2413(ee, AR5K_EEPROM_MODE_11A) +
+ AR5K_EEPROM_N_5GHZ_CHAN / 2;
/* fall through */
case AR5K_EEPROM_MODE_11A:
break;
return offset;
}
+/* Read power calibration for RF2413 chips
+ * For RF2413 we have a PDDAC table (Power Detector) instead
+ * of a PCDAC and 4 pd gain curves for each calibrated channel.
+ * Each curve has PDDAC steps on x axis and power on y axis and
+ * looks like an exponential function. To recreate the curves
+ * we read here the points and interpolate later. Note that
+ * in most cases only higher and lower curves are used (like
+ * RF5112) but vendors have the oportunity to include all 4
+ * curves on eeprom. The final curve (higher power) has an extra
+ * point for better accuracy like RF5112.
+ */
static int
ath5k_eeprom_read_pcal_info_2413(struct ath5k_hw *ah, int mode)
{
ee->ee_pd_gains[mode] = pd_gains;
offset = ath5k_cal_data_offset_2413(ee, mode);
+ ee->ee_n_piers[mode] = 0;
switch (mode) {
case AR5K_EEPROM_MODE_11A:
if (!AR5K_EEPROM_HDR_11A(ee->ee_header))
return 0;
}
+/*
+ * Read per channel calibration info from EEPROM
+ *
+ * This info is used to calibrate the baseband power table. Imagine
+ * that for each channel there is a power curve that's hw specific
+ * (depends on amplifier etc) and we try to "correct" this curve using
+ * offests we pass on to phy chip (baseband -> before amplifier) so that
+ * it can use accurate power values when setting tx power (takes amplifier's
+ * performance on each channel into account).
+ *
+ * EEPROM provides us with the offsets for some pre-calibrated channels
+ * and we have to interpolate to create the full table for these channels and
+ * also the table for any channel.
+ */
static int
ath5k_eeprom_read_pcal_info(struct ath5k_hw *ah)
{
return 0;
}
-/* Read conformance test limits */
+/* Read conformance test limits used for regulatory control */
static int
ath5k_eeprom_read_ctl_info(struct ath5k_hw *ah)
{
git.openpandora.org / pandora-kernel.git / commitdiff