#include <linux/pm_qos.h>
#include <net/sch_generic.h>
#include <linux/slab.h>
+#include <linux/export.h>
#include <net/mac80211.h>
#include "ieee80211_i.h"
if (bss)
ieee80211_rx_bss_put(sdata->local, bss);
- /* If we are on-operating-channel, and this packet is for the
- * current channel, pass the pkt on up the stack so that
- * the rest of the stack can make use of it.
- */
- if (ieee80211_cfg_on_oper_channel(sdata->local)
- && (channel == sdata->local->oper_channel))
- return RX_CONTINUE;
-
dev_kfree_skb(skb);
return RX_QUEUED;
}
enum ieee80211_band band;
int i, ielen, n_chans;
+ if (test_bit(SCAN_HW_CANCELLED, &local->scanning))
+ return false;
+
do {
if (local->hw_scan_band == IEEE80211_NUM_BANDS)
return false;
bool was_hw_scan)
{
struct ieee80211_local *local = hw_to_local(hw);
- bool on_oper_chan;
- bool enable_beacons = false;
lockdep_assert_held(&local->mtx);
local->scanning = 0;
local->scan_channel = NULL;
- on_oper_chan = ieee80211_cfg_on_oper_channel(local);
-
- if (was_hw_scan || !on_oper_chan)
- ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_CHANNEL);
- else
- /* Set power back to normal operating levels. */
- ieee80211_hw_config(local, 0);
-
+ ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_CHANNEL);
if (!was_hw_scan) {
- bool on_oper_chan2;
ieee80211_configure_filter(local);
drv_sw_scan_complete(local);
- on_oper_chan2 = ieee80211_cfg_on_oper_channel(local);
- /* We should always be on-channel at this point. */
- WARN_ON(!on_oper_chan2);
- if (on_oper_chan2 && (on_oper_chan != on_oper_chan2))
- enable_beacons = true;
-
- ieee80211_offchannel_return(local, enable_beacons, true);
+ ieee80211_offchannel_return(local, true);
}
ieee80211_recalc_idle(local);
*/
drv_sw_scan_start(local);
+ ieee80211_offchannel_stop_beaconing(local);
+
local->leave_oper_channel_time = 0;
local->next_scan_state = SCAN_DECISION;
local->scan_channel_idx = 0;
- /* We always want to use off-channel PS, even if we
- * are not really leaving oper-channel. Don't
- * tell the AP though, as long as we are on-channel.
- */
- ieee80211_offchannel_enable_all_ps(local, false);
+ drv_flush(local, false);
ieee80211_configure_filter(local);
}
mutex_unlock(&local->iflist_mtx);
- next_chan = local->scan_req->channels[local->scan_channel_idx];
-
- if (ieee80211_cfg_on_oper_channel(local)) {
- /* We're currently on operating channel. */
- if (next_chan == local->oper_channel)
- /* We don't need to move off of operating channel. */
- local->next_scan_state = SCAN_SET_CHANNEL;
- else
- /*
- * We do need to leave operating channel, as next
- * scan is somewhere else.
- */
- local->next_scan_state = SCAN_LEAVE_OPER_CHANNEL;
- } else {
+ if (local->scan_channel) {
/*
* we're currently scanning a different channel, let's
* see if we can scan another channel without interfering
*
* Otherwise switch back to the operating channel.
*/
+ next_chan = local->scan_req->channels[local->scan_channel_idx];
bad_latency = time_after(jiffies +
ieee80211_scan_get_channel_time(next_chan),
local->next_scan_state = SCAN_ENTER_OPER_CHANNEL;
else
local->next_scan_state = SCAN_SET_CHANNEL;
+ } else {
+ /*
+ * we're on the operating channel currently, let's
+ * leave that channel now to scan another one
+ */
+ local->next_scan_state = SCAN_LEAVE_OPER_CHANNEL;
}
*next_delay = 0;
static void ieee80211_scan_state_leave_oper_channel(struct ieee80211_local *local,
unsigned long *next_delay)
{
- /* PS will already be in off-channel mode,
- * we do that once at the beginning of scanning.
- */
- ieee80211_offchannel_stop_vifs(local, false);
+ ieee80211_offchannel_stop_station(local);
+
+ __set_bit(SCAN_OFF_CHANNEL, &local->scanning);
/*
* What if the nullfunc frames didn't arrive?
{
/* switch back to the operating channel */
local->scan_channel = NULL;
- if (!ieee80211_cfg_on_oper_channel(local))
- ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_CHANNEL);
+ ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_CHANNEL);
/*
- * Re-enable vifs and beaconing. Leave PS
- * in off-channel state..will put that back
- * on-channel at the end of scanning.
+ * Only re-enable station mode interface now; beaconing will be
+ * re-enabled once the full scan has been completed.
*/
- ieee80211_offchannel_return(local, true, false);
+ ieee80211_offchannel_return(local, false);
+
+ __clear_bit(SCAN_OFF_CHANNEL, &local->scanning);
*next_delay = HZ / 5;
local->next_scan_state = SCAN_DECISION;
if (!local->scan_req)
goto out;
+ /*
+ * We have a scan running and the driver already reported completion,
+ * but the worker hasn't run yet or is stuck on the mutex - mark it as
+ * cancelled.
+ */
+ if (test_bit(SCAN_HW_SCANNING, &local->scanning) &&
+ test_bit(SCAN_COMPLETED, &local->scanning)) {
+ set_bit(SCAN_HW_CANCELLED, &local->scanning);
+ goto out;
+ }
+
if (test_bit(SCAN_HW_SCANNING, &local->scanning)) {
+ /*
+ * Make sure that __ieee80211_scan_completed doesn't trigger a
+ * scan on another band.
+ */
+ set_bit(SCAN_HW_CANCELLED, &local->scanning);
if (local->ops->cancel_hw_scan)
drv_cancel_hw_scan(local, local->scan_sdata);
goto out;
git.openpandora.org / pandora-kernel.git / blobdiff