+#ifdef CONFIG_NL80211_TESTMODE
+/**
+ * cfg80211_testmode_alloc_reply_skb - allocate testmode reply
+ * @wiphy: the wiphy
+ * @approxlen: an upper bound of the length of the data that will
+ * be put into the skb
+ *
+ * This function allocates and pre-fills an skb for a reply to
+ * the testmode command. Since it is intended for a reply, calling
+ * it outside of the @testmode_cmd operation is invalid.
+ *
+ * The returned skb (or %NULL if any errors happen) is pre-filled
+ * with the wiphy index and set up in a way that any data that is
+ * put into the skb (with skb_put(), nla_put() or similar) will end
+ * up being within the %NL80211_ATTR_TESTDATA attribute, so all that
+ * needs to be done with the skb is adding data for the corresponding
+ * userspace tool which can then read that data out of the testdata
+ * attribute. You must not modify the skb in any other way.
+ *
+ * When done, call cfg80211_testmode_reply() with the skb and return
+ * its error code as the result of the @testmode_cmd operation.
+ */
+struct sk_buff *cfg80211_testmode_alloc_reply_skb(struct wiphy *wiphy,
+ int approxlen);
+
+/**
+ * cfg80211_testmode_reply - send the reply skb
+ * @skb: The skb, must have been allocated with
+ * cfg80211_testmode_alloc_reply_skb()
+ *
+ * Returns an error code or 0 on success, since calling this
+ * function will usually be the last thing before returning
+ * from the @testmode_cmd you should return the error code.
+ * Note that this function consumes the skb regardless of the
+ * return value.
+ */
+int cfg80211_testmode_reply(struct sk_buff *skb);
+
+/**
+ * cfg80211_testmode_alloc_event_skb - allocate testmode event
+ * @wiphy: the wiphy
+ * @approxlen: an upper bound of the length of the data that will
+ * be put into the skb
+ * @gfp: allocation flags
+ *
+ * This function allocates and pre-fills an skb for an event on the
+ * testmode multicast group.
+ *
+ * The returned skb (or %NULL if any errors happen) is set up in the
+ * same way as with cfg80211_testmode_alloc_reply_skb() but prepared
+ * for an event. As there, you should simply add data to it that will
+ * then end up in the %NL80211_ATTR_TESTDATA attribute. Again, you must
+ * not modify the skb in any other way.
+ *
+ * When done filling the skb, call cfg80211_testmode_event() with the
+ * skb to send the event.
+ */
+struct sk_buff *cfg80211_testmode_alloc_event_skb(struct wiphy *wiphy,
+ int approxlen, gfp_t gfp);
+
+/**
+ * cfg80211_testmode_event - send the event
+ * @skb: The skb, must have been allocated with
+ * cfg80211_testmode_alloc_event_skb()
+ * @gfp: allocation flags
+ *
+ * This function sends the given @skb, which must have been allocated
+ * by cfg80211_testmode_alloc_event_skb(), as an event. It always
+ * consumes it.
+ */
+void cfg80211_testmode_event(struct sk_buff *skb, gfp_t gfp);
+
+#define CFG80211_TESTMODE_CMD(cmd) .testmode_cmd = (cmd),
+#else
+#define CFG80211_TESTMODE_CMD(cmd)
+#endif
+
+/**
+ * cfg80211_connect_result - notify cfg80211 of connection result
+ *
+ * @dev: network device
+ * @bssid: the BSSID of the AP
+ * @req_ie: association request IEs (maybe be %NULL)
+ * @req_ie_len: association request IEs length
+ * @resp_ie: association response IEs (may be %NULL)
+ * @resp_ie_len: assoc response IEs length
+ * @status: status code, 0 for successful connection, use
+ * %WLAN_STATUS_UNSPECIFIED_FAILURE if your device cannot give you
+ * the real status code for failures.
+ * @gfp: allocation flags
+ *
+ * It should be called by the underlying driver whenever connect() has
+ * succeeded.
+ */
+void cfg80211_connect_result(struct net_device *dev, const u8 *bssid,
+ const u8 *req_ie, size_t req_ie_len,
+ const u8 *resp_ie, size_t resp_ie_len,
+ u16 status, gfp_t gfp);
+
+/**
+ * cfg80211_roamed - notify cfg80211 of roaming
+ *
+ * @dev: network device
+ * @bssid: the BSSID of the new AP
+ * @req_ie: association request IEs (maybe be %NULL)
+ * @req_ie_len: association request IEs length
+ * @resp_ie: association response IEs (may be %NULL)
+ * @resp_ie_len: assoc response IEs length
+ * @gfp: allocation flags
+ *
+ * It should be called by the underlying driver whenever it roamed
+ * from one AP to another while connected.
+ */
+void cfg80211_roamed(struct net_device *dev, const u8 *bssid,
+ const u8 *req_ie, size_t req_ie_len,
+ const u8 *resp_ie, size_t resp_ie_len, gfp_t gfp);
+
+/**
+ * cfg80211_disconnected - notify cfg80211 that connection was dropped
+ *
+ * @dev: network device
+ * @ie: information elements of the deauth/disassoc frame (may be %NULL)
+ * @ie_len: length of IEs
+ * @reason: reason code for the disconnection, set it to 0 if unknown
+ * @gfp: allocation flags
+ *
+ * After it calls this function, the driver should enter an idle state
+ * and not try to connect to any AP any more.
+ */
+void cfg80211_disconnected(struct net_device *dev, u16 reason,
+ u8 *ie, size_t ie_len, gfp_t gfp);
+
+