cpuset: PF_SPREAD_PAGE and PF_SPREAD_SLAB should be atomic flags

[pandora-kernel.git] / include / linux / lp.h

diff --git a/include/linux/lp.h b/include/linux/lp.h
index 0df024b..0dd276a 100644 (file)
--- a/include/linux/lp.h
+++ b/include/linux/lp.h
@@ -1,105 +1,16 @@
-#ifndef _LINUX_LP_H
-#define _LINUX_LP_H
-
 /*
  * usr/include/linux/lp.h c.1991-1992 James Wiegand
  * many modifications copyright (C) 1992 Michael K. Johnson
  * Interrupt support added 1993 Nigel Gamble
  * Removed 8255 status defines from inside __KERNEL__ Marcelo Tosatti 
  */
+#ifndef _LINUX_LP_H
+#define _LINUX_LP_H
 
-/*
- * Per POSIX guidelines, this module reserves the LP and lp prefixes
- * These are the lp_table[minor].flags flags...
- */
-#define LP_EXIST 0x0001
-#define LP_SELEC 0x0002
-#define LP_BUSY         0x0004
-#define LP_BUSY_BIT_POS 2
-#define LP_OFFL         0x0008
-#define LP_NOPA  0x0010
-#define LP_ERR   0x0020
-#define LP_ABORT 0x0040
-#define LP_CAREFUL 0x0080 /* obsoleted -arca */
-#define LP_ABORTOPEN 0x0100
-
-#define LP_TRUST_IRQ_  0x0200 /* obsolete */
-#define LP_NO_REVERSE  0x0400 /* No reverse mode available. */
-#define LP_DATA_AVAIL  0x0800 /* Data is available. */
-
-/* 
- * bit defines for 8255 status port
- * base + 1
- * accessed with LP_S(minor), which gets the byte...
- */
-#define LP_PBUSY       0x80  /* inverted input, active high */
-#define LP_PACK                0x40  /* unchanged input, active low */
-#define LP_POUTPA      0x20  /* unchanged input, active high */
-#define LP_PSELECD     0x10  /* unchanged input, active high */
-#define LP_PERRORP     0x08  /* unchanged input, active low */
-
-/* timeout for each character.  This is relative to bus cycles -- it
- * is the count in a busy loop.  THIS IS THE VALUE TO CHANGE if you
- * have extremely slow printing, or if the machine seems to slow down
- * a lot when you print.  If you have slow printing, increase this
- * number and recompile, and if your system gets bogged down, decrease
- * this number.  This can be changed with the tunelp(8) command as well.
- */
-
-#define LP_INIT_CHAR 1000
-
-/* The parallel port specs apparently say that there needs to be
- * a .5usec wait before and after the strobe.
- */
-
-#define LP_INIT_WAIT 1
-
-/* This is the amount of time that the driver waits for the printer to
- * catch up when the printer's buffer appears to be filled.  If you
- * want to tune this and have a fast printer (i.e. HPIIIP), decrease
- * this number, and if you have a slow printer, increase this number.
- * This is in hundredths of a second, the default 2 being .05 second.
- * Or use the tunelp(8) command, which is especially nice if you want
- * change back and forth between character and graphics printing, which
- * are wildly different...
- */
-
-#define LP_INIT_TIME 2
-
-/* IOCTL numbers */
-#define LPCHAR   0x0601  /* corresponds to LP_INIT_CHAR */
-#define LPTIME   0x0602  /* corresponds to LP_INIT_TIME */
-#define LPABORT  0x0604  /* call with TRUE arg to abort on error,
-                           FALSE to retry.  Default is retry.  */
-#define LPSETIRQ 0x0605  /* call with new IRQ number,
-                           or 0 for polling (no IRQ) */
-#define LPGETIRQ 0x0606  /* get the current IRQ number */
-#define LPWAIT   0x0608  /* corresponds to LP_INIT_WAIT */
-/* NOTE: LPCAREFUL is obsoleted and it' s always the default right now -arca */
-#define LPCAREFUL   0x0609  /* call with TRUE arg to require out-of-paper, off-
-                           line, and error indicators good on all writes,
-                           FALSE to ignore them.  Default is ignore. */
-#define LPABORTOPEN 0x060a  /* call with TRUE arg to abort open() on error,
-                           FALSE to ignore error.  Default is ignore.  */
-#define LPGETSTATUS 0x060b  /* return LP_S(minor) */
-#define LPRESET     0x060c  /* reset printer */
-#ifdef LP_STATS
-#define LPGETSTATS  0x060d  /* get statistics (struct lp_stats) */
-#endif
-#define LPGETFLAGS  0x060e  /* get status flags */
-#define LPSETTIMEOUT 0x060f /* set parport timeout */
-
-/* timeout for printk'ing a timeout, in jiffies (100ths of a second).
-   This is also used for re-checking error conditions if LP_ABORT is
-   not set.  This is the default behavior. */
-
-#define LP_TIMEOUT_INTERRUPT   (60 * HZ)
-#define LP_TIMEOUT_POLLED      (10 * HZ)
-
-#ifdef __KERNEL__
 
 #include <linux/wait.h>
 #include <linux/mutex.h>
+#include <uapi/linux/lp.h>
 
 /* Magic numbers for defining port-device mappings */
 #define LP_PARPORT_UNSPEC -4
@@ -187,5 +98,3 @@ struct lp_struct {
 #define LP_DELAY       50
 
 #endif
-
-#endif