#include <linux/usb.h>
#include <linux/timer.h>
+#include <linux/kernel.h>
#include "../core/hcd.h"
/* Code sharing between pci-quirks and xhci hcd */
* xHCI register interface.
* This corresponds to the eXtensible Host Controller Interface (xHCI)
* Revision 0.95 specification
- *
- * Registers should always be accessed with double word or quad word accesses.
- *
- * Some xHCI implementations may support 64-bit address pointers. Registers
- * with 64-bit address pointers should be written to with dword accesses by
- * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
- * xHCI implementations that do not support 64-bit address pointers will ignore
- * the high dword, and write order is irrelevant.
*/
/**
#define HCS_ERST_MAX(p) (((p) >> 4) & 0xf)
/* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
/* bits 27:31 number of Scratchpad buffers SW must allocate for the HW */
+#define HCS_MAX_SCRATCHPAD(p) (((p) >> 27) & 0x1f)
/* HCSPARAMS3 - hcs_params3 - bitmasks */
/* bits 0:7, Max U1 to U0 latency for the roothub ports */
u32 reserved1;
u32 reserved2;
u32 dev_notification;
- u32 cmd_ring[2];
+ u64 cmd_ring;
/* rsvd: offset 0x20-2F */
u32 reserved3[4];
- u32 dcbaa_ptr[2];
+ u64 dcbaa_ptr;
u32 config_reg;
/* rsvd: offset 0x3C-3FF */
u32 reserved4[241];
#define CMD_RING_RUNNING (1 << 3)
/* bits 4:5 reserved and should be preserved */
/* Command Ring pointer - bit mask for the lower 32 bits. */
-#define CMD_RING_ADDR_MASK (0xffffffc0)
+#define CMD_RING_RSVD_BITS (0x3f)
/* CONFIG - Configure Register - config_reg bitmasks */
/* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */
u32 irq_control;
u32 erst_size;
u32 rsvd;
- u32 erst_base[2];
- u32 erst_dequeue[2];
+ u64 erst_base;
+ u64 erst_dequeue;
};
/* irq_pending bitmasks */
#define EPI_TO_DB(p) (((p) + 1) & 0xff)
+/**
+ * struct xhci_container_ctx
+ * @type: Type of context. Used to calculated offsets to contained contexts.
+ * @size: Size of the context data
+ * @bytes: The raw context data given to HW
+ * @dma: dma address of the bytes
+ *
+ * Represents either a Device or Input context. Holds a pointer to the raw
+ * memory used for the context (bytes) and dma address of it (dma).
+ */
+struct xhci_container_ctx {
+ unsigned type;
+#define XHCI_CTX_TYPE_DEVICE 0x1
+#define XHCI_CTX_TYPE_INPUT 0x2
+
+ int size;
+
+ u8 *bytes;
+ dma_addr_t dma;
+};
+
/**
* struct xhci_slot_ctx
* @dev_info: Route string, device speed, hub info, and last valid endpoint
struct xhci_ep_ctx {
u32 ep_info;
u32 ep_info2;
- u32 deq[2];
+ u64 deq;
u32 tx_info;
/* offset 0x14 - 0x1f reserved for HC internal use */
u32 reserved[3];
/**
- * struct xhci_device_control
- * Input/Output context; see section 6.2.5.
+ * struct xhci_input_control_context
+ * Input control context; see section 6.2.5.
*
* @drop_context: set the bit of the endpoint context you want to disable
* @add_context: set the bit of the endpoint context you want to enable
*/
-struct xhci_device_control {
+struct xhci_input_control_ctx {
u32 drop_flags;
u32 add_flags;
- u32 rsvd[6];
- struct xhci_slot_ctx slot;
- struct xhci_ep_ctx ep[31];
+ u32 rsvd2[6];
};
/* drop context bitmasks */
/* add context bitmasks */
#define ADD_EP(x) (0x1 << x)
-
struct xhci_virt_device {
/*
* Commands to the hardware are passed an "input context" that
* track of input and output contexts separately because
* these commands might fail and we don't trust the hardware.
*/
- struct xhci_device_control *out_ctx;
- dma_addr_t out_ctx_dma;
+ struct xhci_container_ctx *out_ctx;
/* Used for addressing devices and configuration changes */
- struct xhci_device_control *in_ctx;
- dma_addr_t in_ctx_dma;
+ struct xhci_container_ctx *in_ctx;
+
/* FIXME when stream support is added */
struct xhci_ring *ep_rings[31];
/* Temporary storage in case the configure endpoint command fails and we
*/
struct xhci_device_context_array {
/* 64-bit device addresses; we only write 32-bit addresses */
- u32 dev_context_ptrs[2*MAX_HC_SLOTS];
+ u64 dev_context_ptrs[MAX_HC_SLOTS];
/* private xHCD pointers */
dma_addr_t dma;
};
struct xhci_stream_ctx {
/* 64-bit stream ring address, cycle state, and stream type */
- u32 stream_ring[2];
+ u64 stream_ring;
/* offset 0x14 - 0x1f reserved for HC internal use */
u32 reserved[2];
};
struct xhci_transfer_event {
/* 64-bit buffer address, or immediate data */
- u32 buffer[2];
+ u64 buffer;
u32 transfer_len;
/* This field is interpreted differently based on the type of TRB */
u32 flags;
struct xhci_link_trb {
/* 64-bit segment pointer*/
- u32 segment_ptr[2];
+ u64 segment_ptr;
u32 intr_target;
u32 control;
};
/* Command completion event TRB */
struct xhci_event_cmd {
/* Pointer to command TRB, or the value passed by the event data trb */
- u32 cmd_trb[2];
+ u64 cmd_trb;
u32 status;
u32 flags;
};
#define TRB_CONFIG_EP 12
/* Evaluate Context Command */
#define TRB_EVAL_CONTEXT 13
-/* Reset Transfer Ring Command */
-#define TRB_RESET_RING 14
+/* Reset Endpoint Command */
+#define TRB_RESET_EP 14
/* Stop Transfer Ring Command */
#define TRB_STOP_RING 15
/* Set Transfer Ring Dequeue Pointer Command */
unsigned int cancels_pending;
unsigned int state;
#define SET_DEQ_PENDING (1 << 0)
+#define EP_HALTED (1 << 1)
/* The TRB that was last reported in a stopped endpoint ring */
union xhci_trb *stopped_trb;
struct xhci_td *stopped_td;
u32 cycle_state;
};
+struct xhci_dequeue_state {
+ struct xhci_segment *new_deq_seg;
+ union xhci_trb *new_deq_ptr;
+ int new_cycle_state;
+};
+
struct xhci_erst_entry {
/* 64-bit event ring segment address */
- u32 seg_addr[2];
+ u64 seg_addr;
u32 seg_size;
/* Set to zero */
u32 rsvd;
unsigned int erst_size;
};
+struct xhci_scratchpad {
+ u64 *sp_array;
+ dma_addr_t sp_dma;
+ void **sp_buffers;
+ dma_addr_t *sp_dma_buffers;
+};
+
/*
* Each segment table entry is 4*32bits long. 1K seems like an ok size:
* (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table,
struct xhci_ring *cmd_ring;
struct xhci_ring *event_ring;
struct xhci_erst erst;
+ /* Scratchpad */
+ struct xhci_scratchpad *scratchpad;
+
/* slot enabling and address device helpers */
struct completion addr_dev;
int slot_id;
static inline void xhci_writel(struct xhci_hcd *xhci,
const unsigned int val, __u32 __iomem *regs)
{
- if (!in_interrupt())
- xhci_dbg(xhci,
- "`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n",
- regs, val);
+ xhci_dbg(xhci,
+ "`MEM_WRITE_DWORD(3'b000, 32'h%p, 32'h%0x, 4'hf);\n",
+ regs, val);
writel(val, regs);
}
+/*
+ * Registers should always be accessed with double word or quad word accesses.
+ *
+ * Some xHCI implementations may support 64-bit address pointers. Registers
+ * with 64-bit address pointers should be written to with dword accesses by
+ * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
+ * xHCI implementations that do not support 64-bit address pointers will ignore
+ * the high dword, and write order is irrelevant.
+ */
+static inline u64 xhci_read_64(const struct xhci_hcd *xhci,
+ __u64 __iomem *regs)
+{
+ __u32 __iomem *ptr = (__u32 __iomem *) regs;
+ u64 val_lo = readl(ptr);
+ u64 val_hi = readl(ptr + 1);
+ return val_lo + (val_hi << 32);
+}
+static inline void xhci_write_64(struct xhci_hcd *xhci,
+ const u64 val, __u64 __iomem *regs)
+{
+ __u32 __iomem *ptr = (__u32 __iomem *) regs;
+ u32 val_lo = lower_32_bits(val);
+ u32 val_hi = upper_32_bits(val);
+
+ xhci_dbg(xhci,
+ "`MEM_WRITE_DWORD(3'b000, 64'h%p, 64'h%0lx, 4'hf);\n",
+ regs, (long unsigned int) val);
+ writel(val_lo, ptr);
+ writel(val_hi, ptr + 1);
+}
+
/* xHCI debugging */
void xhci_print_ir_set(struct xhci_hcd *xhci, struct xhci_intr_reg *ir_set, int set_num);
void xhci_print_registers(struct xhci_hcd *xhci);
void xhci_dbg_erst(struct xhci_hcd *xhci, struct xhci_erst *erst);
void xhci_dbg_cmd_ptrs(struct xhci_hcd *xhci);
void xhci_dbg_ring_ptrs(struct xhci_hcd *xhci, struct xhci_ring *ring);
-void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_device_control *ctx, dma_addr_t dma, unsigned int last_ep);
+void xhci_dbg_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int last_ep);
/* xHCI memory managment */
void xhci_mem_cleanup(struct xhci_hcd *xhci);
int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status);
int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep);
int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, struct usb_host_endpoint *ep);
+void xhci_endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep);
int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
int slot_id, unsigned int ep_index);
int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
u32 slot_id);
+int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id,
+ unsigned int ep_index);
+void xhci_find_new_dequeue_state(struct xhci_hcd *xhci,
+ unsigned int slot_id, unsigned int ep_index,
+ struct xhci_td *cur_td, struct xhci_dequeue_state *state);
+void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci,
+ struct xhci_ring *ep_ring, unsigned int slot_id,
+ unsigned int ep_index, struct xhci_dequeue_state *deq_state);
/* xHCI roothub code */
int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, u16 wIndex,
char *buf, u16 wLength);
int xhci_hub_status_data(struct usb_hcd *hcd, char *buf);
+/* xHCI contexts */
+struct xhci_input_control_ctx *xhci_get_input_control_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx);
+struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx);
+struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci, struct xhci_container_ctx *ctx, unsigned int ep_index);
+
#endif /* __LINUX_XHCI_HCD_H */
git.openpandora.org / pandora-kernel.git / blobdiff