Jan Lee 2006-09-15 RT2860. Change for 802.11n , EEPROM, Led, BA, HT.
*/
#include "../rt_config.h"
-#include "firmware.h"
+#ifndef RT30xx
+#ifdef RT2860
+#include "firmware.h"
#include <linux/bitrev.h>
+#endif
+#ifdef RT2870
+#include "../../rt2870/common/firmware.h"
+#endif
+#endif
+#ifdef RT30xx
+#include "../../rt3070/firmware.h"
+#endif
UCHAR BIT8[] = {0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80};
ULONG BIT32[] = {0x00000001, 0x00000002, 0x00000004, 0x00000008,
#define ByteCRC16(v, crc) \
(unsigned short)((crc << 8) ^ ccitt_16Table[((crc >> 8) ^ (v)) & 255])
+#ifdef RT2870
+unsigned char BitReverse(unsigned char x)
+{
+ int i;
+ unsigned char Temp=0;
+ for(i=0; ; i++)
+ {
+ if(x & 0x80) Temp |= 0x80;
+ if(i==7) break;
+ x <<= 1;
+ Temp >>= 1;
+ }
+ return Temp;
+}
+#endif
+
//
// BBP register initialization set
//
//
// RF register initialization set
//
+#ifdef RT2870
+REG_PAIR RT30xx_RFRegTable[] = {
+ {RF_R04, 0x40},
+ {RF_R05, 0x03},
+ {RF_R06, 0x02},
+ {RF_R07, 0x70},
+ {RF_R09, 0x0F},
+#ifndef RT30xx
+ {RF_R10, 0x71},
+#endif
+#ifdef RT30xx
+ {RF_R10, 0x41},
+#endif
+ {RF_R11, 0x21},
+ {RF_R12, 0x7B},
+ {RF_R14, 0x90},
+ {RF_R15, 0x58},
+ {RF_R16, 0xB3},
+ {RF_R17, 0x92},
+ {RF_R18, 0x2C},
+ {RF_R19, 0x02},
+ {RF_R20, 0xBA},
+ {RF_R21, 0xDB},
+ {RF_R24, 0x16},
+ {RF_R25, 0x01},
+#ifndef RT30xx
+ {RF_R27, 0x03},
+#endif
+ {RF_R29, 0x1F},
+};
+#define NUM_RF_REG_PARMS (sizeof(RT30xx_RFRegTable) / sizeof(REG_PAIR))
+#endif // RT2870 //
//
// ASIC register initialization sets
{AUTO_RSP_CFG, 0x00000013}, // Initial Auto_Responder, because QA will turn off Auto-Responder
{CCK_PROT_CFG, 0x05740003 /*0x01740003*/}, // Initial Auto_Responder, because QA will turn off Auto-Responder. And RTS threshold is enabled.
{OFDM_PROT_CFG, 0x05740003 /*0x01740003*/}, // Initial Auto_Responder, because QA will turn off Auto-Responder. And RTS threshold is enabled.
+//PS packets use Tx1Q (for HCCA) when dequeue from PS unicast queue (WiFi WPA2 MA9_DT1 for Marvell B STA)
+#ifdef RT2870
+ {PBF_CFG, 0xf40006}, // Only enable Queue 2
+ {MM40_PROT_CFG, 0x3F44084}, // Initial Auto_Responder, because QA will turn off Auto-Responder
+ {WPDMA_GLO_CFG, 0x00000030},
+#endif // RT2870 //
{GF20_PROT_CFG, 0x01744004}, // set 19:18 --> Short NAV for MIMO PS
{GF40_PROT_CFG, 0x03F44084},
{MM20_PROT_CFG, 0x01744004},
+#ifdef RT2860
{MM40_PROT_CFG, 0x03F54084},
+#endif
{TXOP_CTRL_CFG, 0x0000583f, /*0x0000243f*/ /*0x000024bf*/}, //Extension channel backoff.
{TX_RTS_CFG, 0x00092b20},
{EXP_ACK_TIME, 0x002400ca}, // default value
{PWR_PIN_CFG, 0x00000003}, // patch for 2880-E
};
-
-#ifdef CONFIG_STA_SUPPORT
RTMP_REG_PAIR STAMACRegTable[] = {
{WMM_AIFSN_CFG, 0x00002273},
{WMM_CWMIN_CFG, 0x00002344},
{WMM_CWMAX_CFG, 0x000034aa},
};
-#endif // CONFIG_STA_SUPPORT //
#define NUM_MAC_REG_PARMS (sizeof(MACRegTable) / sizeof(RTMP_REG_PAIR))
-#ifdef CONFIG_STA_SUPPORT
#define NUM_STA_MAC_REG_PARMS (sizeof(STAMACRegTable) / sizeof(RTMP_REG_PAIR))
-#endif // CONFIG_STA_SUPPORT //
+#ifdef RT2870
+//
+// RT2870 Firmware Spec only used 1 oct for version expression
+//
+#define FIRMWARE_MINOR_VERSION 7
+
+#endif // RT2870 //
// New 8k byte firmware size for RT3071/RT3072
#define FIRMWAREIMAGE_MAX_LENGTH 0x2000
#define FIRMWAREIMAGEV1_LENGTH 0x1000
#define FIRMWAREIMAGEV2_LENGTH 0x1000
+#ifdef RT2860
#define FIRMWARE_MINOR_VERSION 2
+#endif
/*
// Init spin locks
NdisAllocateSpinLock(&pAd->MgmtRingLock);
+#ifdef RT2860
NdisAllocateSpinLock(&pAd->RxRingLock);
+#endif
for (index =0 ; index < NUM_OF_TX_RING; index++)
{
// 4. Print and Debug
choffset = 14 + 12 + 16 + 7;
-
-
-#if 0
- // Init the 802.11j channel number for TX channel power
- // 0. 20MHz
- for (i = 0; i < 3; i++)
- {
- pAd->TxPower11J[i].Channel = 8 + i * 4;
- pAd->TxPower11J[i].BW = BW_20;
- }
-
- for (i = 0; i < 4; i++)
- {
- pAd->TxPower11J[i + 3].Channel = 34 + i * 4;
- pAd->TxPower11J[i + 3].BW = BW_20;
- }
-
- for (i = 0; i < 4; i++)
- {
- pAd->TxPower11J[i + 7].Channel = 184 + i * 4;
- pAd->TxPower11J[i + 7].BW = BW_20;
- }
-
- // 0. 10MHz
- for (i = 0; i < 2; i++)
- {
- pAd->TxPower11J[i + 11].Channel = 7 + i;
- pAd->TxPower11J[i + 11].BW = BW_10;
- }
- pAd->TxPower11J[13].Channel = 11;
- pAd->TxPower11J[13].BW = BW_10;
-
- for (i = 0; i < 3; i++)
- {
- pAd->TxPower11J[i + 14].Channel = 183 + i;
- pAd->TxPower11J[i + 14].BW= BW_10;
- }
-
- for (i = 0; i < 3; i++)
- {
- pAd->TxPower11J[i + 17].Channel = 187 + i;
- pAd->TxPower11J[i + 17].BW = BW_10;
- }
- for (i = 0; i < 10; i++)
- {
- Power.word = RTMP_EEPROM_READ16(pAd, EEPROM_Japan_TX_PWR_OFFSET + i * 2);
- Power2.word = RTMP_EEPROM_READ16(pAd, EEPROM_Japan_TX2_PWR_OFFSET + i * 2);
-
- if ((Power.field.Byte0 < 36) && (Power.field.Byte0 > -6))
- pAd->TxPower11J[i * 2].Power = Power.field.Byte0;
-
- if ((Power.field.Byte1 < 36) && (Power.field.Byte1 > -6))
- pAd->TxPower11J[i * 2 + 1].Power = Power.field.Byte1;
-
- if ((Power2.field.Byte0 < 36) && (Power2.field.Byte0 > -6))
- pAd->TxPower11J[i * 2].Power2 = Power2.field.Byte0;
-
- if ((Power2.field.Byte1 < 36) && (Power2.field.Byte1 > -6))
- pAd->TxPower11J[i * 2 + 1].Power2 = Power2.field.Byte1;
- }
-#endif
}
/*
}
+#ifdef RT2870
+/*
+ ========================================================================
+
+ Routine Description:
+ For RF filter calibration purpose
+
+ Arguments:
+ pAd Pointer to our adapter
+
+ Return Value:
+ None
+
+ IRQL = PASSIVE_LEVEL
+
+ ========================================================================
+*/
+#ifndef RT30xx
+VOID RTUSBFilterCalibration(
+ IN PRTMP_ADAPTER pAd)
+{
+ UCHAR R55x = 0, value, FilterTarget = 0x1E, BBPValue;
+ UINT loop = 0, count = 0, loopcnt = 0, ReTry = 0;
+ UCHAR RF_R24_Value = 0;
+
+ // Give bbp filter initial value
+ pAd->Mlme.CaliBW20RfR24 = 0x16;
+ pAd->Mlme.CaliBW40RfR24 = 0x36; //Bit[5] must be 1 for BW 40
+
+ do
+ {
+ if (loop == 1) //BandWidth = 40 MHz
+ {
+ // Write 0x27 to RF_R24 to program filter
+ RF_R24_Value = 0x27;
+ RT30xxWriteRFRegister(pAd, RF_R24, RF_R24_Value);
+ FilterTarget = 0x19;
+
+ // when calibrate BW40, BBP mask must set to BW40.
+ RTUSBReadBBPRegister(pAd, BBP_R4, &BBPValue);
+ BBPValue&= (~0x18);
+ BBPValue|= (0x10);
+ RTUSBWriteBBPRegister(pAd, BBP_R4, BBPValue);
+ }
+ else //BandWidth = 20 MHz
+ {
+ // Write 0x07 to RF_R24 to program filter
+ RF_R24_Value = 0x07;
+ RT30xxWriteRFRegister(pAd, RF_R24, RF_R24_Value);
+ FilterTarget = 0x16;
+ }
+
+ // Write 0x01 to RF_R22 to enable baseband loopback mode
+ RT30xxReadRFRegister(pAd, RF_R22, &value);
+ value |= 0x01;
+ RT30xxWriteRFRegister(pAd, RF_R22, value);
+
+ // Write 0x00 to BBP_R24 to set power & frequency of passband test tone
+ RTUSBWriteBBPRegister(pAd, BBP_R24, 0);
+
+ do
+ {
+ // Write 0x90 to BBP_R25 to transmit test tone
+ RTUSBWriteBBPRegister(pAd, BBP_R25, 0x90);
+
+ RTMPusecDelay(1000);
+ // Read BBP_R55[6:0] for received power, set R55x = BBP_R55[6:0]
+ RTUSBReadBBPRegister(pAd, BBP_R55, &value);
+ R55x = value & 0xFF;
+
+ } while ((ReTry++ < 100) && (R55x == 0));
+
+ // Write 0x06 to BBP_R24 to set power & frequency of stopband test tone
+ RTUSBWriteBBPRegister(pAd, BBP_R24, 0x06);
+
+ while(TRUE)
+ {
+ // Write 0x90 to BBP_R25 to transmit test tone
+ RTUSBWriteBBPRegister(pAd, BBP_R25, 0x90);
+
+ //We need to wait for calibration
+ RTMPusecDelay(1000);
+ RTUSBReadBBPRegister(pAd, BBP_R55, &value);
+ value &= 0xFF;
+ if ((R55x - value) < FilterTarget)
+ {
+ RF_R24_Value ++;
+ }
+ else if ((R55x - value) == FilterTarget)
+ {
+ RF_R24_Value ++;
+ count ++;
+ }
+ else
+ {
+ break;
+ }
+
+ // prevent infinite loop cause driver hang.
+ if (loopcnt++ > 100)
+ {
+ DBGPRINT(RT_DEBUG_ERROR, ("RTUSBFilterCalibration - can't find a valid value, loopcnt=%d stop calibrating", loopcnt));
+ break;
+ }
+
+ // Write RF_R24 to program filter
+ RT30xxWriteRFRegister(pAd, RF_R24, RF_R24_Value);
+ }
+
+ if (count > 0)
+ {
+ RF_R24_Value = RF_R24_Value - ((count) ? (1) : (0));
+ }
+
+ // Store for future usage
+ if (loopcnt < 100)
+ {
+ if (loop++ == 0)
+ {
+ //BandWidth = 20 MHz
+ pAd->Mlme.CaliBW20RfR24 = (UCHAR)RF_R24_Value;
+ }
+ else
+ {
+ //BandWidth = 40 MHz
+ pAd->Mlme.CaliBW40RfR24 = (UCHAR)RF_R24_Value;
+ break;
+ }
+ }
+ else
+ break;
+
+ RT30xxWriteRFRegister(pAd, RF_R24, RF_R24_Value);
+
+ // reset count
+ count = 0;
+ } while(TRUE);
+
+ //
+ // Set back to initial state
+ //
+ RTUSBWriteBBPRegister(pAd, BBP_R24, 0);
+
+ RT30xxReadRFRegister(pAd, RF_R22, &value);
+ value &= ~(0x01);
+ RT30xxWriteRFRegister(pAd, RF_R22, value);
+
+ // set BBP back to BW20
+ RTUSBReadBBPRegister(pAd, BBP_R4, &BBPValue);
+ BBPValue&= (~0x18);
+ RTUSBWriteBBPRegister(pAd, BBP_R4, BBPValue);
+
+ DBGPRINT(RT_DEBUG_TRACE, ("RTUSBFilterCalibration - CaliBW20RfR24=0x%x, CaliBW40RfR24=0x%x\n", pAd->Mlme.CaliBW20RfR24, pAd->Mlme.CaliBW40RfR24));
+}
+#endif /* RT30xx */
+#ifdef RT30xx
+VOID RTMPFilterCalibration(
+ IN PRTMP_ADAPTER pAd)
+{
+ UCHAR R55x = 0, value, FilterTarget = 0x1E, BBPValue=0;
+ UINT loop = 0, count = 0, loopcnt = 0, ReTry = 0;
+ UCHAR RF_R24_Value = 0;
+
+ // Give bbp filter initial value
+ pAd->Mlme.CaliBW20RfR24 = 0x1F;
+ pAd->Mlme.CaliBW40RfR24 = 0x2F; //Bit[5] must be 1 for BW 40
+
+ do
+ {
+ if (loop == 1) //BandWidth = 40 MHz
+ {
+ // Write 0x27 to RF_R24 to program filter
+ RF_R24_Value = 0x27;
+ RT30xxWriteRFRegister(pAd, RF_R24, RF_R24_Value);
+ if (IS_RT3090(pAd))
+ FilterTarget = 0x15;
+ else
+ FilterTarget = 0x19;
+
+ // when calibrate BW40, BBP mask must set to BW40.
+ RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R4, &BBPValue);
+ BBPValue&= (~0x18);
+ BBPValue|= (0x10);
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R4, BBPValue);
+
+ // set to BW40
+ RT30xxReadRFRegister(pAd, RF_R31, &value);
+ value |= 0x20;
+ RT30xxWriteRFRegister(pAd, RF_R31, value);
+ }
+ else //BandWidth = 20 MHz
+ {
+ // Write 0x07 to RF_R24 to program filter
+ RF_R24_Value = 0x07;
+ RT30xxWriteRFRegister(pAd, RF_R24, RF_R24_Value);
+ if (IS_RT3090(pAd))
+ FilterTarget = 0x13;
+ else
+ FilterTarget = 0x16;
+
+ // set to BW20
+ RT30xxReadRFRegister(pAd, RF_R31, &value);
+ value &= (~0x20);
+ RT30xxWriteRFRegister(pAd, RF_R31, value);
+ }
+
+ // Write 0x01 to RF_R22 to enable baseband loopback mode
+ RT30xxReadRFRegister(pAd, RF_R22, &value);
+ value |= 0x01;
+ RT30xxWriteRFRegister(pAd, RF_R22, value);
+
+ // Write 0x00 to BBP_R24 to set power & frequency of passband test tone
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R24, 0);
+
+ do
+ {
+ // Write 0x90 to BBP_R25 to transmit test tone
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R25, 0x90);
+
+ RTMPusecDelay(1000);
+ // Read BBP_R55[6:0] for received power, set R55x = BBP_R55[6:0]
+ RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R55, &value);
+ R55x = value & 0xFF;
+
+ } while ((ReTry++ < 100) && (R55x == 0));
+
+ // Write 0x06 to BBP_R24 to set power & frequency of stopband test tone
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R24, 0x06);
+
+ while(TRUE)
+ {
+ // Write 0x90 to BBP_R25 to transmit test tone
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R25, 0x90);
+
+ //We need to wait for calibration
+ RTMPusecDelay(1000);
+ RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R55, &value);
+ value &= 0xFF;
+ if ((R55x - value) < FilterTarget)
+ {
+ RF_R24_Value ++;
+ }
+ else if ((R55x - value) == FilterTarget)
+ {
+ RF_R24_Value ++;
+ count ++;
+ }
+ else
+ {
+ break;
+ }
+
+ // prevent infinite loop cause driver hang.
+ if (loopcnt++ > 100)
+ {
+ DBGPRINT(RT_DEBUG_ERROR, ("RTMPFilterCalibration - can't find a valid value, loopcnt=%d stop calibrating", loopcnt));
+ break;
+ }
+
+ // Write RF_R24 to program filter
+ RT30xxWriteRFRegister(pAd, RF_R24, RF_R24_Value);
+ }
+
+ if (count > 0)
+ {
+ RF_R24_Value = RF_R24_Value - ((count) ? (1) : (0));
+ }
+
+ // Store for future usage
+ if (loopcnt < 100)
+ {
+ if (loop++ == 0)
+ {
+ //BandWidth = 20 MHz
+ pAd->Mlme.CaliBW20RfR24 = (UCHAR)RF_R24_Value;
+ }
+ else
+ {
+ //BandWidth = 40 MHz
+ pAd->Mlme.CaliBW40RfR24 = (UCHAR)RF_R24_Value;
+ break;
+ }
+ }
+ else
+ break;
+
+ RT30xxWriteRFRegister(pAd, RF_R24, RF_R24_Value);
+
+ // reset count
+ count = 0;
+ } while(TRUE);
+
+ //
+ // Set back to initial state
+ //
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R24, 0);
+
+ RT30xxReadRFRegister(pAd, RF_R22, &value);
+ value &= ~(0x01);
+ RT30xxWriteRFRegister(pAd, RF_R22, value);
+
+ // set BBP back to BW20
+ RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R4, &BBPValue);
+ BBPValue&= (~0x18);
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R4, BBPValue);
+
+ DBGPRINT(RT_DEBUG_TRACE, ("RTMPFilterCalibration - CaliBW20RfR24=0x%x, CaliBW40RfR24=0x%x\n", pAd->Mlme.CaliBW20RfR24, pAd->Mlme.CaliBW40RfR24));
+}
+#endif /* RT30xx */
+
+VOID NICInitRT30xxRFRegisters(IN PRTMP_ADAPTER pAd)
+{
+ INT i;
+ // Driver must read EEPROM to get RfIcType before initial RF registers
+ // Initialize RF register to default value
+#ifndef RT30xx
+ if (IS_RT3070(pAd) && ((pAd->RfIcType == RFIC_3020) ||(pAd->RfIcType == RFIC_2020)))
+ {
+ // Init RF calibration
+ // Driver should toggle RF R30 bit7 before init RF registers
+ ULONG RfReg = 0;
+ RT30xxReadRFRegister(pAd, RF_R30, (PUCHAR)&RfReg);
+ RfReg |= 0x80;
+ RT30xxWriteRFRegister(pAd, RF_R30, (UCHAR)RfReg);
+ RTMPusecDelay(1000);
+ RfReg &= 0x7F;
+ RT30xxWriteRFRegister(pAd, RF_R30, (UCHAR)RfReg);
+
+ // Initialize RF register to default value
+ for (i = 0; i < NUM_RF_REG_PARMS; i++)
+ {
+ RT30xxWriteRFRegister(pAd, RT30xx_RFRegTable[i].Register, RT30xx_RFRegTable[i].Value);
+ }
+
+ //For RF filter Calibration
+ RTUSBFilterCalibration(pAd);
+ }
+#endif
+#ifdef RT30xx
+ if (IS_RT3070(pAd) || IS_RT3071(pAd))
+ {
+ // Init RF calibration
+ // Driver should toggle RF R30 bit7 before init RF registers
+ UINT32 RfReg = 0;
+ UINT32 data;
+
+ RT30xxReadRFRegister(pAd, RF_R30, (PUCHAR)&RfReg);
+ RfReg |= 0x80;
+ RT30xxWriteRFRegister(pAd, RF_R30, (UCHAR)RfReg);
+ RTMPusecDelay(1000);
+ RfReg &= 0x7F;
+ RT30xxWriteRFRegister(pAd, RF_R30, (UCHAR)RfReg);
+
+ // Initialize RF register to default value
+ for (i = 0; i < NUM_RF_REG_PARMS; i++)
+ {
+ RT30xxWriteRFRegister(pAd, RT30xx_RFRegTable[i].Register, RT30xx_RFRegTable[i].Value);
+ }
+
+ // add by johnli
+ if (IS_RT3070(pAd))
+ {
+ // Update MAC 0x05D4 from 01xxxxxx to 0Dxxxxxx (voltage 1.2V to 1.35V) for RT3070 to improve yield rate
+ RTUSBReadMACRegister(pAd, LDO_CFG0, &data);
+ data = ((data & 0xF0FFFFFF) | 0x0D000000);
+ RTUSBWriteMACRegister(pAd, LDO_CFG0, data);
+ }
+ else if (IS_RT3071(pAd))
+ {
+ // Driver should set RF R6 bit6 on before init RF registers
+ RT30xxReadRFRegister(pAd, RF_R06, (PUCHAR)&RfReg);
+ RfReg |= 0x40;
+ RT30xxWriteRFRegister(pAd, RF_R06, (UCHAR)RfReg);
+
+ // init R31
+ RT30xxWriteRFRegister(pAd, RF_R31, 0x14);
+
+ // RT3071 version E has fixed this issue
+ if ((pAd->NicConfig2.field.DACTestBit == 1) && ((pAd->MACVersion & 0xffff) < 0x0211))
+ {
+ // patch tx EVM issue temporarily
+ RTUSBReadMACRegister(pAd, LDO_CFG0, &data);
+ data = ((data & 0xE0FFFFFF) | 0x0D000000);
+ RTUSBWriteMACRegister(pAd, LDO_CFG0, data);
+ }
+ else
+ {
+ RTMP_IO_READ32(pAd, LDO_CFG0, &data);
+ data = ((data & 0xE0FFFFFF) | 0x01000000);
+ RTMP_IO_WRITE32(pAd, LDO_CFG0, data);
+ }
+
+ // patch LNA_PE_G1 failed issue
+ RTUSBReadMACRegister(pAd, GPIO_SWITCH, &data);
+ data &= ~(0x20);
+ RTUSBWriteMACRegister(pAd, GPIO_SWITCH, data);
+ }
+
+ //For RF filter Calibration
+ RTMPFilterCalibration(pAd);
+
+ // Initialize RF R27 register, set RF R27 must be behind RTMPFilterCalibration()
+ if ((pAd->MACVersion & 0xffff) < 0x0211)
+ RT30xxWriteRFRegister(pAd, RF_R27, 0x3);
+
+ // set led open drain enable
+ RTUSBReadMACRegister(pAd, OPT_14, &data);
+ data |= 0x01;
+ RTUSBWriteMACRegister(pAd, OPT_14, data);
+
+ if (IS_RT3071(pAd))
+ {
+ // add by johnli, RF power sequence setup, load RF normal operation-mode setup
+ RT30xxLoadRFNormalModeSetup(pAd);
+ }
+ }
+#endif
+}
+#endif // RT2870 //
/*
Antenna.word = pAd->EEPROMDefaultValue[0];
if (Antenna.word == 0xFFFF)
{
+#ifdef RT30xx
+ if(IS_RT3090(pAd))
+ {
+ Antenna.word = 0;
+ Antenna.field.RfIcType = RFIC_3020;
+ Antenna.field.TxPath = 1;
+ Antenna.field.RxPath = 1;
+ }
+ else
+ {
+#endif // RT30xx //
Antenna.word = 0;
Antenna.field.RfIcType = RFIC_2820;
Antenna.field.TxPath = 1;
Antenna.field.RxPath = 2;
DBGPRINT(RT_DEBUG_WARN, ("E2PROM error, hard code as 0x%04x\n", Antenna.word));
+#ifdef RT30xx
+ }
+#endif // RT30xx //
}
// Choose the desired Tx&Rx stream.
NicConfig2.word = pAd->EEPROMDefaultValue[1];
-
-
-#ifdef CONFIG_STA_SUPPORT
- IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
+#ifndef RT30xx
NicConfig2.word = 0;
+#endif
if ((NicConfig2.word & 0x00ff) == 0xff)
{
NicConfig2.word &= 0xff00;
NicConfig2.word &= 0x00ff;
}
}
-#endif // CONFIG_STA_SUPPORT //
if (NicConfig2.field.DynamicTxAgcControl == 1)
pAd->bAutoTxAgcA = pAd->bAutoTxAgcG = TRUE;
if ((pAd->CommonCfg.PhyMode == PHY_11ABG_MIXED) ||
(pAd->CommonCfg.PhyMode == PHY_11A))
pAd->CommonCfg.PhyMode = PHY_11BG_MIXED;
-#ifdef DOT11_N_SUPPORT
else if ((pAd->CommonCfg.PhyMode == PHY_11ABGN_MIXED) ||
(pAd->CommonCfg.PhyMode == PHY_11AN_MIXED) ||
(pAd->CommonCfg.PhyMode == PHY_11AGN_MIXED) ||
(pAd->CommonCfg.PhyMode == PHY_11N_5G))
pAd->CommonCfg.PhyMode = PHY_11BGN_MIXED;
-#endif // DOT11_N_SUPPORT //
}
// Read TSSI reference and TSSI boundary for temperature compensation. This is ugly
TmpPhy = pAd->CommonCfg.PhyMode;
pAd->CommonCfg.PhyMode = 0xff;
RTMPSetPhyMode(pAd, TmpPhy);
-#ifdef DOT11_N_SUPPORT
SetCommonHT(pAd);
-#endif // DOT11_N_SUPPORT //
}
//
RTMPReadTxPwrPerRate(pAd);
-#ifdef SINGLE_SKU
- //pAd->CommonCfg.DefineMaxTxPwr = RTMP_EEPROM_READ16(pAd, EEPROM_DEFINE_MAX_TXPWR);
- RT28xx_EEPROM_READ16(pAd, EEPROM_DEFINE_MAX_TXPWR, pAd->CommonCfg.DefineMaxTxPwr);
-#endif // SINGLE_SKU //
+#ifdef RT30xx
+ if (IS_RT30xx(pAd))
+ {
+ eFusePhysicalReadRegisters(pAd, EFUSE_TAG, 2, &value);
+ pAd->EFuseTag = (value & 0xff);
+ }
+#endif // RT30xx //
DBGPRINT(RT_DEBUG_TRACE, ("<-- NICReadEEPROMParameters\n"));
}
VOID NICInitAsicFromEEPROM(
IN PRTMP_ADAPTER pAd)
{
-#ifdef CONFIG_STA_SUPPORT
UINT32 data = 0;
UCHAR BBPR1 = 0;
-#endif // CONFIG_STA_SUPPORT //
USHORT i;
EEPROM_ANTENNA_STRUC Antenna;
EEPROM_NIC_CONFIG2_STRUC NicConfig2;
}
}
+#ifndef RT30xx
Antenna.word = pAd->Antenna.word;
+#endif
+#ifdef RT30xx
+ Antenna.word = pAd->EEPROMDefaultValue[0];
+ if (Antenna.word == 0xFFFF)
+ {
+ DBGPRINT(RT_DEBUG_ERROR, ("E2PROM error, hard code as 0x%04x\n", Antenna.word));
+ BUG_ON(Antenna.word == 0xFFFF);
+ }
+#endif
pAd->Mlme.RealRxPath = (UCHAR) Antenna.field.RxPath;
pAd->RfIcType = (UCHAR) Antenna.field.RfIcType;
+#ifdef RT30xx
+ DBGPRINT(RT_DEBUG_WARN, ("pAd->RfIcType = %d, RealRxPath=%d, TxPath = %d\n", pAd->RfIcType, pAd->Mlme.RealRxPath,Antenna.field.TxPath));
+
+ // Save the antenna for future use
+ pAd->Antenna.word = Antenna.word;
+#endif
NicConfig2.word = pAd->EEPROMDefaultValue[1];
+#ifdef RT30xx
+ {
+ if ((NicConfig2.word & 0x00ff) == 0xff)
+ {
+ NicConfig2.word &= 0xff00;
+ }
+ if ((NicConfig2.word >> 8) == 0xff)
+ {
+ NicConfig2.word &= 0x00ff;
+ }
+ }
+#endif
// Save the antenna for future use
pAd->NicConfig2.word = NicConfig2.word;
+#ifdef RT30xx
+ // set default antenna as main
+ if (pAd->RfIcType == RFIC_3020)
+ AsicSetRxAnt(pAd, pAd->RxAnt.Pair1PrimaryRxAnt);
+#endif
//
// Send LED Setting to MCU.
//
pAd->LedCntl.word = 0x01;
pAd->Led1 = 0x5555;
pAd->Led2 = 0x2221;
+#ifdef RT2860
pAd->Led3 = 0xA9F8;
+#endif
+
+#ifdef RT2870
+ pAd->Led3 = 0x5627;
+#endif // RT2870 //
}
AsicSendCommandToMcu(pAd, 0x52, 0xff, (UCHAR)pAd->Led1, (UCHAR)(pAd->Led1 >> 8));
pAd->LedIndicatorStregth = 0xFF;
RTMPSetSignalLED(pAd, -100); // Force signal strength Led to be turned off, before link up
-#ifdef CONFIG_STA_SUPPORT
- IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
// Read Hardware controlled Radio state enable bit
if (NicConfig2.field.HardwareRadioControl == 1)
else
{
RTMPSetLED(pAd, LED_RADIO_ON);
+#ifdef RT2860
AsicSendCommandToMcu(pAd, 0x30, 0xff, 0xff, 0x02);
AsicSendCommandToMcu(pAd, 0x31, PowerWakeCID, 0x00, 0x00);
// 2-1. wait command ok.
AsicCheckCommanOk(pAd, PowerWakeCID);
+#endif
}
}
-#endif // CONFIG_STA_SUPPORT //
// Turn off patching for cardbus controller
if (NicConfig2.field.CardbusAcceleration == 1)
}
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R3, BBPR3);
-#ifdef CONFIG_STA_SUPPORT
- IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
// Handle the difference when 1T
RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R1, &BBPR1);
DBGPRINT(RT_DEBUG_TRACE, ("Use Hw Radio Control Pin=%d; if used Pin=%d;\n", pAd->CommonCfg.bHardwareRadio, pAd->CommonCfg.bHardwareRadio));
}
-#endif // CONFIG_STA_SUPPORT //
+
DBGPRINT(RT_DEBUG_TRACE, ("TxPath = %d, RxPath = %d, RFIC=%d, Polar+LED mode=%x\n", pAd->Antenna.field.TxPath, pAd->Antenna.field.RxPath, pAd->RfIcType, pAd->LedCntl.word));
DBGPRINT(RT_DEBUG_TRACE, ("<-- NICInitAsicFromEEPROM\n"));
}
{
NDIS_STATUS Status = NDIS_STATUS_SUCCESS;
WPDMA_GLO_CFG_STRUC GloCfg;
+#ifdef RT2860
UINT32 Value;
DELAY_INT_CFG_STRUC IntCfg;
+#endif
ULONG i =0, j=0;
AC_TXOP_CSR0_STRUC csr0;
// asic simulation sequence put this ahead before loading firmware.
// pbf hardware reset
+#ifdef RT2860
RTMP_IO_WRITE32(pAd, WPDMA_RST_IDX, 0x1003f); // 0x10000 for reset rx, 0x3f resets all 6 tx rings.
RTMP_IO_WRITE32(pAd, PBF_SYS_CTRL, 0xe1f);
RTMP_IO_WRITE32(pAd, PBF_SYS_CTRL, 0xe00);
+#endif
// Initialze ASIC for TX & Rx operation
if (NICInitializeAsic(pAd , bHardReset) != NDIS_STATUS_SUCCESS)
}
+#ifdef RT2860
// Write AC_BK base address register
Value = RTMP_GetPhysicalAddressLow(pAd->TxRing[QID_AC_BK].Cell[0].AllocPa);
RTMP_IO_WRITE32(pAd, TX_BASE_PTR1, Value);
// Write RX_RING_CSR register
Value = RX_RING_SIZE;
RTMP_IO_WRITE32(pAd, RX_MAX_CNT, Value);
+#endif /* RT2860 */
// WMM parameter
RTMP_IO_WRITE32(pAd, WMM_TXOP1_CFG, csr0.word);
+#ifdef RT2860
// 3. Set DMA global configuration except TX_DMA_EN and RX_DMA_EN bits:
i = 0;
do
IntCfg.word = 0;
RTMP_IO_WRITE32(pAd, DELAY_INT_CFG, IntCfg.word);
+#endif
// reset action
ULONG Index = 0;
UCHAR R0 = 0xff;
UINT32 MacCsr12 = 0, Counter = 0;
+#ifdef RT2870
+ UINT32 MacCsr0 = 0;
+ NTSTATUS Status;
+ UCHAR Value = 0xff;
+#endif // RT2870 //
+#ifdef RT30xx
+ UINT32 eFuseCtrl;
+#endif // RT30xx //
USHORT KeyIdx;
INT i,apidx;
DBGPRINT(RT_DEBUG_TRACE, ("--> NICInitializeAsic\n"));
+#ifdef RT2860
if (bHardReset == TRUE)
{
RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x3);
}
else
RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x1);
+#endif
+#ifdef RT2870
+ //
+ // Make sure MAC gets ready after NICLoadFirmware().
+ //
+ Index = 0;
+
+ //To avoid hang-on issue when interface up in kernel 2.4,
+ //we use a local variable "MacCsr0" instead of using "pAd->MACVersion" directly.
+ do
+ {
+ RTMP_IO_READ32(pAd, MAC_CSR0, &MacCsr0);
+
+ if ((MacCsr0 != 0x00) && (MacCsr0 != 0xFFFFFFFF))
+ break;
+
+ RTMPusecDelay(10);
+ } while (Index++ < 100);
+
+ pAd->MACVersion = MacCsr0;
+ DBGPRINT(RT_DEBUG_TRACE, ("MAC_CSR0 [ Ver:Rev=0x%08x]\n", pAd->MACVersion));
+ // turn on bit13 (set to zero) after rt2860D. This is to solve high-current issue.
+ RTMP_IO_READ32(pAd, PBF_SYS_CTRL, &MacCsr12);
+ MacCsr12 &= (~0x2000);
+ RTMP_IO_WRITE32(pAd, PBF_SYS_CTRL, MacCsr12);
+
+ RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x3);
+ RTMP_IO_WRITE32(pAd, USB_DMA_CFG, 0x0);
+ Status = RTUSBVenderReset(pAd);
+#endif
RTMP_IO_WRITE32(pAd, MAC_SYS_CTRL, 0x0);
+
// Initialize MAC register to default value
+#ifdef RT2860
for (Index = 0; Index < NUM_MAC_REG_PARMS; Index++)
{
RTMP_IO_WRITE32(pAd, MACRegTable[Index].Register, MACRegTable[Index].Value);
}
+#endif
+#ifdef RT2870
+ for(Index=0; Index<NUM_MAC_REG_PARMS; Index++)
+ {
+#ifdef RT3070
+ if ((MACRegTable[Index].Register == TX_SW_CFG0) && (IS_RT3070(pAd) || IS_RT3071(pAd)))
+ {
+ MACRegTable[Index].Value = 0x00000400;
+ }
+#endif // RT3070 //
+ RTMP_IO_WRITE32(pAd, (USHORT)MACRegTable[Index].Register, MACRegTable[Index].Value);
+ }
+
+#ifndef RT30xx
+ if(IS_RT3070(pAd))
+ {
+ // According to Frank Hsu (from Gary Tsao)
+ RTMP_IO_WRITE32(pAd, (USHORT)TX_SW_CFG0, 0x00000400);
+
+ // Initialize RT3070 serial MAC registers which is different from RT2870 serial
+ RTUSBWriteMACRegister(pAd, TX_SW_CFG1, 0);
+ RTUSBWriteMACRegister(pAd, TX_SW_CFG2, 0);
+ }
+#endif
+#endif // RT2870 //
-#ifdef CONFIG_STA_SUPPORT
- IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
for (Index = 0; Index < NUM_STA_MAC_REG_PARMS; Index++)
{
+#ifdef RT2860
RTMP_IO_WRITE32(pAd, STAMACRegTable[Index].Register, STAMACRegTable[Index].Value);
+#endif
+#ifdef RT2870
+ RTMP_IO_WRITE32(pAd, (USHORT)STAMACRegTable[Index].Register, STAMACRegTable[Index].Value);
+#endif
}
}
-#endif // CONFIG_STA_SUPPORT //
+#ifdef RT30xx
+ // Initialize RT3070 serial MAc registers which is different from RT2870 serial
+ if (IS_RT3090(pAd))
+ {
+ RTMP_IO_WRITE32(pAd, TX_SW_CFG1, 0);
+
+ // RT3071 version E has fixed this issue
+ if ((pAd->MACVersion & 0xffff) < 0x0211)
+ {
+ if (pAd->NicConfig2.field.DACTestBit == 1)
+ {
+ RTMP_IO_WRITE32(pAd, TX_SW_CFG2, 0x1F); // To fix throughput drop drastically
+ }
+ else
+ {
+ RTMP_IO_WRITE32(pAd, TX_SW_CFG2, 0x0F); // To fix throughput drop drastically
+ }
+ }
+ else
+ {
+ RTMP_IO_WRITE32(pAd, TX_SW_CFG2, 0x0);
+ }
+ }
+ else if (IS_RT3070(pAd))
+ {
+ RTMP_IO_WRITE32(pAd, TX_SW_CFG1, 0);
+ RTMP_IO_WRITE32(pAd, TX_SW_CFG2, 0x1F); // To fix throughput drop drastically
+ }
+#endif // RT30xx //
//
// Before program BBP, we need to wait BBP/RF get wake up.
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBPRegTable[Index].Register, BBPRegTable[Index].Value);
}
+#ifndef RT30xx
// for rt2860E and after, init BBP_R84 with 0x19. This is for extension channel overlapping IOT.
if ((pAd->MACVersion&0xffff) != 0x0101)
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R84, 0x19);
+#ifdef RT2870
+ //write RT3070 BBP wchich different with 2870 after write RT2870 BBP
+ if (IS_RT3070(pAd))
+ {
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R70, 0x0a);
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R84, 0x99);
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R105, 0x05);
+ }
+#endif // RT2870 //
+#endif
+#ifdef RT30xx
+ // for rt2860E and after, init BBP_R84 with 0x19. This is for extension channel overlapping IOT.
+ // RT3090 should not program BBP R84 to 0x19, otherwise TX will block.
+ if (((pAd->MACVersion&0xffff) != 0x0101) && (!IS_RT30xx(pAd)))
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R84, 0x19);
+
+// add by johnli, RF power sequence setup
+ if (IS_RT30xx(pAd))
+ { //update for RT3070/71/72/90/91/92.
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R79, 0x13);
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R80, 0x05);
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R81, 0x33);
+ }
+
+ if (IS_RT3090(pAd))
+ {
+ UCHAR bbpreg=0;
+
+ // enable DC filter
+ if ((pAd->MACVersion & 0xffff) >= 0x0211)
+ {
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R103, 0xc0);
+ }
+
+ // improve power consumption
+ RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R138, &bbpreg);
+ if (pAd->Antenna.field.TxPath == 1)
+ {
+ // turn off tx DAC_1
+ bbpreg = (bbpreg | 0x20);
+ }
+
+ if (pAd->Antenna.field.RxPath == 1)
+ {
+ // turn off tx ADC_1
+ bbpreg &= (~0x2);
+ }
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R138, bbpreg);
+ // improve power consumption in RT3071 Ver.E
+ if ((pAd->MACVersion & 0xffff) >= 0x0211)
+ {
+ RTMP_BBP_IO_READ8_BY_REG_ID(pAd, BBP_R31, &bbpreg);
+ bbpreg &= (~0x3);
+ RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R31, bbpreg);
+ }
+ }
+#endif
if (pAd->MACVersion == 0x28600100)
{
RTMP_BBP_IO_WRITE8_BY_REG_ID(pAd, BBP_R69, 0x16);
RTMP_IO_WRITE32(pAd, MAX_LEN_CFG, csr);
}
+#ifdef RT2870
+{
+ UCHAR MAC_Value[]={0xff,0xff,0xff,0xff,0xff,0xff,0xff,0,0};
+
+ //Initialize WCID table
+ Value = 0xff;
+ for(Index =0 ;Index < 254;Index++)
+ {
+ RTUSBMultiWrite(pAd, (USHORT)(MAC_WCID_BASE + Index * 8), MAC_Value, 8);
+ }
+}
+#endif // RT2870 //
// Add radio off control
-#ifdef CONFIG_STA_SUPPORT
- IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
if (pAd->StaCfg.bRadio == FALSE)
{
DBGPRINT(RT_DEBUG_TRACE, ("Set Radio Off\n"));
}
}
-#endif // CONFIG_STA_SUPPORT //
// Clear raw counters
RTMP_IO_READ32(pAd, RX_STA_CNT0, &Counter);
RTMP_IO_WRITE32(pAd, pAd->BeaconOffset[apidx] + i, 0x00);
}
}
+#ifdef RT2870
+ AsicDisableSync(pAd);
+ // Clear raw counters
+ RTMP_IO_READ32(pAd, RX_STA_CNT0, &Counter);
+ RTMP_IO_READ32(pAd, RX_STA_CNT1, &Counter);
+ RTMP_IO_READ32(pAd, RX_STA_CNT2, &Counter);
+ RTMP_IO_READ32(pAd, TX_STA_CNT0, &Counter);
+ RTMP_IO_READ32(pAd, TX_STA_CNT1, &Counter);
+ RTMP_IO_READ32(pAd, TX_STA_CNT2, &Counter);
+ // Default PCI clock cycle per ms is different as default setting, which is based on PCI.
+ RTMP_IO_READ32(pAd, USB_CYC_CFG, &Counter);
+ Counter&=0xffffff00;
+ Counter|=0x000001e;
+ RTMP_IO_WRITE32(pAd, USB_CYC_CFG, Counter);
+#endif // RT2870 //
+#ifdef RT30xx
+ pAd->bUseEfuse=FALSE;
+ RTMP_IO_READ32(pAd, EFUSE_CTRL, &eFuseCtrl);
+ pAd->bUseEfuse = ( (eFuseCtrl & 0x80000000) == 0x80000000) ? 1 : 0;
+ if(pAd->bUseEfuse)
+ {
+ DBGPRINT(RT_DEBUG_TRACE, ("NVM is Efuse\n"));
+ }
+ else
+ {
+ DBGPRINT(RT_DEBUG_TRACE, ("NVM is EEPROM\n"));
+
+ }
+#endif // RT30xx //
-#ifdef CONFIG_STA_SUPPORT
- IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
// for rt2860E and after, init TXOP_CTRL_CFG with 0x583f. This is for extension channel overlapping IOT.
if ((pAd->MACVersion&0xffff) != 0x0101)
RTMP_IO_WRITE32(pAd, TXOP_CTRL_CFG, 0x583f);
}
-#endif // CONFIG_STA_SUPPORT //
DBGPRINT(RT_DEBUG_TRACE, ("<-- NICInitializeAsic\n"));
return NDIS_STATUS_SUCCESS;
}
+#ifdef RT2860
VOID NICRestoreBBPValue(
IN PRTMP_ADAPTER pAd)
{
DBGPRINT(RT_DEBUG_TRACE, ("<--- NICRestoreBBPValue !!!!!!!!!!!!!!!!!!!!!!! \n"));
}
+#endif /* RT2860 */
/*
========================================================================
pEntry->DebugFIFOCount++;
-#ifdef DOT11_N_SUPPORT
if (StaFifo.field.TxBF) // 3*3
pEntry->TxBFCount++;
-#endif // DOT11_N_SUPPORT //
#ifdef UAPSD_AP_SUPPORT
UAPSD_SP_AUE_Handle(pAd, pEntry, StaFifo.field.TxSuccess);
if (pEntry->FIFOCount >= 1)
{
DBGPRINT(RT_DEBUG_TRACE, ("#"));
-#if 0
- SendRefreshBAR(pAd, pEntry);
- pEntry->NoBADataCountDown = 64;
-#else
-#ifdef DOT11_N_SUPPORT
pEntry->NoBADataCountDown = 64;
-#endif // DOT11_N_SUPPORT //
if(pEntry->PsMode == PWR_ACTIVE)
{
-#ifdef DOT11_N_SUPPORT
int tid;
for (tid=0; tid<NUM_OF_TID; tid++)
{
BAOriSessionTearDown(pAd, pEntry->Aid, tid, FALSE, FALSE);
}
-#endif // DOT11_N_SUPPORT //
// Update the continuous transmission counter except PS mode
pEntry->ContinueTxFailCnt++;
pEntry->FIFOCount = 0;
pEntry->ContinueTxFailCnt = 0;
}
-#endif
- //pEntry->FIFOCount = 0;
}
- //pEntry->bSendBAR = TRUE;
}
else
{
-#ifdef DOT11_N_SUPPORT
if ((pEntry->PsMode != PWR_SAVE) && (pEntry->NoBADataCountDown > 0))
{
pEntry->NoBADataCountDown--;
DBGPRINT(RT_DEBUG_TRACE, ("@\n"));
}
}
-#endif // DOT11_N_SUPPORT //
+
pEntry->FIFOCount = 0;
pEntry->OneSecTxNoRetryOkCount++;
// update NoDataIdleCount when sucessful send packet to STA.
// Update RX Overflow counter
pAd->Counters8023.RxNoBuffer += (RxStaCnt2.field.RxFifoOverflowCount);
+#ifdef RT2870
+ if (pAd->RalinkCounters.RxCount != pAd->watchDogRxCnt)
+ {
+ pAd->watchDogRxCnt = pAd->RalinkCounters.RxCount;
+ pAd->watchDogRxOverFlowCnt = 0;
+ }
+ else
+ {
+ if (RxStaCnt2.field.RxFifoOverflowCount)
+ pAd->watchDogRxOverFlowCnt++;
+ else
+ pAd->watchDogRxOverFlowCnt = 0;
+ }
+#endif // RT2870 //
+
+
if (!pAd->bUpdateBcnCntDone)
{
// Update BEACON sent count
ULONG FileLength, Index;
//ULONG firm;
UINT32 MacReg = 0;
+#ifdef RT2870
+ UINT32 Version = (pAd->MACVersion >> 16);
+#endif // RT2870 //
pFirmwareImage = FirmwareImage;
FileLength = sizeof(FirmwareImage);
+#ifdef RT2870
+ // New 8k byte firmware size for RT3071/RT3072
+ //printk("Usb Chip\n");
+ if (FIRMWAREIMAGE_LENGTH == FIRMWAREIMAGE_MAX_LENGTH)
+ //The firmware image consists of two parts. One is the origianl and the other is the new.
+ //Use Second Part
+ {
+ if ((Version != 0x2860) && (Version != 0x2872) && (Version != 0x3070))
+ { // Use Firmware V2.
+ //printk("KH:Use New Version,part2\n");
+ pFirmwareImage = (PUCHAR)&FirmwareImage[FIRMWAREIMAGEV1_LENGTH];
+ FileLength = FIRMWAREIMAGEV2_LENGTH;
+ }
+ else
+ {
+ //printk("KH:Use New Version,part1\n");
+ pFirmwareImage = FirmwareImage;
+ FileLength = FIRMWAREIMAGEV1_LENGTH;
+ }
+ }
+ else
+ {
+ DBGPRINT(RT_DEBUG_ERROR, ("KH: bin file should be 8KB.\n"));
+ Status = NDIS_STATUS_FAILURE;
+ }
+
+#endif // RT2870 //
+
RT28XX_WRITE_FIRMWARE(pAd, pFirmwareImage, FileLength);
/* check if MCU is ready */
RTMPusecDelay(1000);
} while (Index++ < 1000);
- if (Index >= 1000)
+ if (Index > 1000)
{
Status = NDIS_STATUS_FAILURE;
DBGPRINT(RT_DEBUG_ERROR, ("NICLoadFirmware: MCU is not ready\n\n\n"));
//
// part I. intialize common configuration
//
+#ifdef RT2870
+ pAd->BulkOutReq = 0;
+
+ pAd->BulkOutComplete = 0;
+ pAd->BulkOutCompleteOther = 0;
+ pAd->BulkOutCompleteCancel = 0;
+ pAd->BulkInReq = 0;
+ pAd->BulkInComplete = 0;
+ pAd->BulkInCompleteFail = 0;
+
+ //pAd->QuickTimerP = 100;
+ //pAd->TurnAggrBulkInCount = 0;
+ pAd->bUsbTxBulkAggre = 0;
+
+ // init as unsed value to ensure driver will set to MCU once.
+ pAd->LedIndicatorStregth = 0xFF;
+
+ pAd->CommonCfg.MaxPktOneTxBulk = 2;
+ pAd->CommonCfg.TxBulkFactor = 1;
+ pAd->CommonCfg.RxBulkFactor =1;
+
+ pAd->CommonCfg.TxPower = 100; //mW
+
+ NdisZeroMemory(&pAd->CommonCfg.IOTestParm, sizeof(pAd->CommonCfg.IOTestParm));
+#endif // RT2870 //
for(key_index=0; key_index<SHARE_KEY_NUM; key_index++)
{
}
}
+#ifdef RT30xx
+ pAd->EepromAccess = FALSE;
+#endif
pAd->Antenna.word = 0;
pAd->CommonCfg.BBPCurrentBW = BW_20;
pAd->LedCntl.word = 0;
+#ifdef RT2860
pAd->LedIndicatorStregth = 0;
pAd->RLnkCtrlOffset = 0;
pAd->HostLnkCtrlOffset = 0;
pAd->CheckDmaBusyCount = 0;
+#endif
pAd->bAutoTxAgcA = FALSE; // Default is OFF
pAd->bAutoTxAgcG = FALSE; // Default is OFF
NdisZeroMemory(&pAd->BeaconTxWI, sizeof(pAd->BeaconTxWI));
-#ifdef DOT11_N_SUPPORT
NdisZeroMemory(&pAd->CommonCfg.HtCapability, sizeof(pAd->CommonCfg.HtCapability));
pAd->HTCEnable = FALSE;
pAd->bBroadComHT = FALSE;
pAd->CommonCfg.bRdg = FALSE;
-#ifdef DOT11N_DRAFT3
- pAd->CommonCfg.Dot11OBssScanPassiveDwell = dot11OBSSScanPassiveDwell; // Unit : TU. 5~1000
- pAd->CommonCfg.Dot11OBssScanActiveDwell = dot11OBSSScanActiveDwell; // Unit : TU. 10~1000
- pAd->CommonCfg.Dot11BssWidthTriggerScanInt = dot11BSSWidthTriggerScanInterval; // Unit : Second
- pAd->CommonCfg.Dot11OBssScanPassiveTotalPerChannel = dot11OBSSScanPassiveTotalPerChannel; // Unit : TU. 200~10000
- pAd->CommonCfg.Dot11OBssScanActiveTotalPerChannel = dot11OBSSScanActiveTotalPerChannel; // Unit : TU. 20~10000
- pAd->CommonCfg.Dot11BssWidthChanTranDelayFactor = dot11BSSWidthChannelTransactionDelayFactor;
- pAd->CommonCfg.Dot11OBssScanActivityThre = dot11BSSScanActivityThreshold; // Unit : percentage
- pAd->CommonCfg.Dot11BssWidthChanTranDelay = (pAd->CommonCfg.Dot11BssWidthTriggerScanInt * pAd->CommonCfg.Dot11BssWidthChanTranDelayFactor);
-#endif // DOT11N_DRAFT3 //
-
NdisZeroMemory(&pAd->CommonCfg.AddHTInfo, sizeof(pAd->CommonCfg.AddHTInfo));
pAd->CommonCfg.BACapability.field.MMPSmode = MMPS_ENABLE;
pAd->CommonCfg.BACapability.field.MpduDensity = 0;
pAd->CommonCfg.TxBASize = 7;
pAd->CommonCfg.REGBACapability.word = pAd->CommonCfg.BACapability.word;
-#endif // DOT11_N_SUPPORT //
//pAd->CommonCfg.HTPhyMode.field.BW = BW_20;
//pAd->CommonCfg.HTPhyMode.field.MCS = MCS_AUTO;
//
// part II. intialize STA specific configuration
//
-#ifdef CONFIG_STA_SUPPORT
- IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
RX_FILTER_SET_FLAG(pAd, fRX_FILTER_ACCEPT_DIRECT);
RX_FILTER_CLEAR_FLAG(pAd, fRX_FILTER_ACCEPT_MULTICAST);
pAd->StaCfg.bAutoTxRateSwitch = TRUE;
pAd->StaCfg.DesiredTransmitSetting.field.MCS = MCS_AUTO;
}
-#endif // CONFIG_STA_SUPPORT //
// global variables mXXXX used in MAC protocol state machines
OPSTATUS_SET_FLAG(pAd, fOP_STATUS_RECEIVE_DTIM);
pAd->CommonCfg.PhyMode = PHY_11BG_MIXED; // default PHY mode
OPSTATUS_CLEAR_FLAG(pAd, fOP_STATUS_SHORT_PREAMBLE_INUSED); // CCK use LONG preamble
-#ifdef CONFIG_STA_SUPPORT
- IF_DEV_CONFIG_OPMODE_ON_STA(pAd)
{
// user desired power mode
pAd->StaCfg.WindowsPowerMode = Ndis802_11PowerModeCAM;
pAd->StaCfg.WindowsBatteryPowerMode = Ndis802_11PowerModeCAM;
pAd->StaCfg.bWindowsACCAMEnable = FALSE;
-#ifdef LEAP_SUPPORT
- // CCX v1.0 releated init value
- RTMPInitTimer(pAd, &pAd->StaCfg.LeapAuthTimer, GET_TIMER_FUNCTION(LeapAuthTimeout), pAd, FALSE);
- pAd->StaCfg.LeapAuthMode = CISCO_AuthModeLEAPNone;
- pAd->StaCfg.bCkipOn = FALSE;
-#endif // LEAP_SUPPORT //
-
RTMPInitTimer(pAd, &pAd->StaCfg.StaQuickResponeForRateUpTimer, GET_TIMER_FUNCTION(StaQuickResponeForRateUpExec), pAd, FALSE);
pAd->StaCfg.StaQuickResponeForRateUpTimerRunning = FALSE;
NdisZeroMemory(pAd->nickname, IW_ESSID_MAX_SIZE+1);
sprintf(pAd->nickname, "%s", STA_NIC_DEVICE_NAME);
RTMPInitTimer(pAd, &pAd->StaCfg.WpaDisassocAndBlockAssocTimer, GET_TIMER_FUNCTION(WpaDisassocApAndBlockAssoc), pAd, FALSE);
-#ifdef WPA_SUPPLICANT_SUPPORT
pAd->StaCfg.IEEE8021X = FALSE;
pAd->StaCfg.IEEE8021x_required_keys = FALSE;
pAd->StaCfg.WpaSupplicantUP = WPA_SUPPLICANT_DISABLE;
-#ifdef NATIVE_WPA_SUPPLICANT_SUPPORT
pAd->StaCfg.WpaSupplicantUP = WPA_SUPPLICANT_ENABLE;
-#endif // NATIVE_WPA_SUPPLICANT_SUPPORT //
-#endif // WPA_SUPPLICANT_SUPPORT //
-
}
-#endif // CONFIG_STA_SUPPORT //
// Default for extra information is not valid
pAd->ExtraInfo = EXTRA_INFO_CLEAR;
NdisAllocateSpinLock(&pAd->MacTabLock);
pAd->CommonCfg.bWiFiTest = FALSE;
+#ifdef RT2860
pAd->bPCIclkOff = FALSE;
RTMP_SET_PSFLAG(pAd, fRTMP_PS_CAN_GO_SLEEP);
+#endif
DBGPRINT(RT_DEBUG_TRACE, ("<-- UserCfgInit\n"));
}
pTimer->State = FALSE;
pTimer->cookie = (ULONG) pData;
+#ifdef RT2870
+ pTimer->pAd = pAd;
+#endif // RT2870 //
RTMP_OS_Init_Timer(pAd, &pTimer->TimerObj, pTimerFunc, (PVOID) pTimer);
}
if (*pCancelled == TRUE)
pTimer->State = TRUE;
+#ifdef RT2870
+ // We need to go-through the TimerQ to findout this timer handler and remove it if
+ // it's still waiting for execution.
+
+ RT2870_TimerQ_Remove(pTimer->pAd, pTimer);
+#endif // RT2870 //
}
else
{
git.openpandora.org / pandora-kernel.git / blobdiff