}
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_PCI_MASTER, quirk_mediagx_master );
-/*
- * As per PCI spec, ignore base address registers 0-3 of the IDE controllers
- * running in Compatible mode (bits 0 and 2 in the ProgIf for primary and
- * secondary channels respectively). If the device reports Compatible mode
- * but does use BAR0-3 for address decoding, we assume that firmware has
- * programmed these BARs with standard values (0x1f0,0x3f4 and 0x170,0x374).
- * Exceptions (if they exist) must be handled in chip/architecture specific
- * fixups.
- *
- * Note: for non x86 people. You may need an arch specific quirk to handle
- * moving IDE devices to native mode as well. Some plug in card devices power
- * up in compatible mode and assume the BIOS will adjust them.
- *
- * Q: should we load the 0x1f0,0x3f4 into the registers or zap them as
- * we do now ? We don't want is pci_enable_device to come along
- * and assign new resources. Both approaches work for that.
- */
-static void __devinit quirk_ide_bases(struct pci_dev *dev)
-{
- struct resource *res;
- int first_bar = 2, last_bar = 0;
-
- if ((dev->class >> 8) != PCI_CLASS_STORAGE_IDE)
- return;
-
- res = &dev->resource[0];
-
- /* primary channel: ProgIf bit 0, BAR0, BAR1 */
- if (!(dev->class & 1) && (res[0].flags || res[1].flags)) {
- res[0].start = res[0].end = res[0].flags = 0;
- res[1].start = res[1].end = res[1].flags = 0;
- first_bar = 0;
- last_bar = 1;
- }
-
- /* secondary channel: ProgIf bit 2, BAR2, BAR3 */
- if (!(dev->class & 4) && (res[2].flags || res[3].flags)) {
- res[2].start = res[2].end = res[2].flags = 0;
- res[3].start = res[3].end = res[3].flags = 0;
- last_bar = 3;
- }
-
- if (!last_bar)
- return;
-
- printk(KERN_INFO "PCI: Ignoring BAR%d-%d of IDE controller %s\n",
- first_bar, last_bar, pci_name(dev));
-}
-DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_ide_bases);
-
/*
* Ensure C0 rev restreaming is off. This is normally done by
* the BIOS but in the odd case it is not the results are corruption
prog &= ~5;
pdev->class &= ~5;
pci_write_config_byte(pdev, PCI_CLASS_PROG, prog);
- /* need to re-assign BARs for compat mode */
- quirk_ide_bases(pdev);
+ /* PCI layer will sort out resources */
}
}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide );
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, quirk_svwks_csb5ide );
/*
* Intel 82801CAM ICH3-M datasheet says IDE modes must be the same
prog &= ~5;
pdev->class &= ~5;
pci_write_config_byte(pdev, PCI_CLASS_PROG, prog);
- /* need to re-assign BARs for compat mode */
- quirk_ide_bases(pdev);
}
}
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, quirk_ide_samemode);
/* This was originally an Alpha specific thing, but it really fits here.
* The i82375 PCI/EISA bridge appears as non-classified. Fix that.
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260a, quirk_intel_pcie_pm);
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x260b, quirk_intel_pcie_pm);
-/*
- * Fixup the cardbus bridges on the IBM Dock II docking station
- */
-static void __devinit quirk_ibm_dock2_cardbus(struct pci_dev *dev)
-{
- u32 val;
-
- /*
- * tie the 2 interrupt pins to INTA, and configure the
- * multifunction routing register to handle this.
- */
- if ((dev->subsystem_vendor == PCI_VENDOR_ID_IBM) &&
- (dev->subsystem_device == 0x0148)) {
- printk(KERN_INFO "PCI: Found IBM Dock II Cardbus Bridge "
- "applying quirk\n");
- pci_read_config_dword(dev, 0x8c, &val);
- val = ((val & 0xffffff00) | 0x1002);
- pci_write_config_dword(dev, 0x8c, val);
- pci_read_config_dword(dev, 0x80, &val);
- val = ((val & 0x00ffff00) | 0x2864c077);
- pci_write_config_dword(dev, 0x80, val);
- }
-}
-
-DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_1420,
- quirk_ibm_dock2_cardbus);
-
static void __devinit quirk_netmos(struct pci_dev *dev)
{
unsigned int num_parallel = (dev->subsystem_device & 0xf0) >> 4;
* a single one having MSI is enough to be sure that MSI are supported.
*/
pdev = pci_get_slot(dev->bus, 0);
- if (dev->subordinate && !msi_ht_cap_enabled(dev)
- && !msi_ht_cap_enabled(pdev)) {
+ if (!msi_ht_cap_enabled(dev) && !msi_ht_cap_enabled(pdev)) {
printk(KERN_WARNING "PCI: MSI quirk detected. "
"MSI disabled on chipset %s.\n",
pci_name(dev));
git.openpandora.org / pandora-kernel.git / blobdiff