#include "rt2x00pci.h"
#include "rt61pci.h"
+/*
+ * Allow hardware encryption to be disabled.
+ */
+static int modparam_nohwcrypt = 0;
+module_param_named(nohwcrypt, modparam_nohwcrypt, bool, S_IRUGO);
+MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption.");
+
/*
* Register access.
* BBP and RF register require indirect register access,
rt2x00_rf_write(rt2x00dev, word, value);
}
-#ifdef CONFIG_RT61PCI_LEDS
+#ifdef CONFIG_RT2X00_LIB_LEDS
/*
* This function is only called from rt61pci_led_brightness()
* make gcc happy by placing this function inside the
rt2x00_set_field32(®, HOST_CMD_CSR_INTERRUPT_MCU, 1);
rt2x00pci_register_write(rt2x00dev, HOST_CMD_CSR, reg);
}
-#endif /* CONFIG_RT61PCI_LEDS */
+#endif /* CONFIG_RT2X00_LIB_LEDS */
static void rt61pci_eepromregister_read(struct eeprom_93cx6 *eeprom)
{
};
#endif /* CONFIG_RT2X00_LIB_DEBUGFS */
-#ifdef CONFIG_RT61PCI_RFKILL
+#ifdef CONFIG_RT2X00_LIB_RFKILL
static int rt61pci_rfkill_poll(struct rt2x00_dev *rt2x00dev)
{
u32 reg;
}
#else
#define rt61pci_rfkill_poll NULL
-#endif /* CONFIG_RT61PCI_RFKILL */
+#endif /* CONFIG_RT2X00_LIB_RFKILL */
-#ifdef CONFIG_RT61PCI_LEDS
+#ifdef CONFIG_RT2X00_LIB_LEDS
static void rt61pci_brightness_set(struct led_classdev *led_cdev,
enum led_brightness brightness)
{
led->led_dev.blink_set = rt61pci_blink_set;
led->flags = LED_INITIALIZED;
}
-#endif /* CONFIG_RT61PCI_LEDS */
+#endif /* CONFIG_RT2X00_LIB_LEDS */
/*
* Configuration handlers.
*/
+static int rt61pci_config_shared_key(struct rt2x00_dev *rt2x00dev,
+ struct rt2x00lib_crypto *crypto,
+ struct ieee80211_key_conf *key)
+{
+ struct hw_key_entry key_entry;
+ struct rt2x00_field32 field;
+ u32 mask;
+ u32 reg;
+
+ if (crypto->cmd == SET_KEY) {
+ /*
+ * rt2x00lib can't determine the correct free
+ * key_idx for shared keys. We have 1 register
+ * with key valid bits. The goal is simple, read
+ * the register, if that is full we have no slots
+ * left.
+ * Note that each BSS is allowed to have up to 4
+ * shared keys, so put a mask over the allowed
+ * entries.
+ */
+ mask = (0xf << crypto->bssidx);
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR0, ®);
+ reg &= mask;
+
+ if (reg && reg == mask)
+ return -ENOSPC;
+
+ key->hw_key_idx += reg ? ffz(reg) : 0;
+
+ /*
+ * Upload key to hardware
+ */
+ memcpy(key_entry.key, crypto->key,
+ sizeof(key_entry.key));
+ memcpy(key_entry.tx_mic, crypto->tx_mic,
+ sizeof(key_entry.tx_mic));
+ memcpy(key_entry.rx_mic, crypto->rx_mic,
+ sizeof(key_entry.rx_mic));
+
+ reg = SHARED_KEY_ENTRY(key->hw_key_idx);
+ rt2x00pci_register_multiwrite(rt2x00dev, reg,
+ &key_entry, sizeof(key_entry));
+
+ /*
+ * The cipher types are stored over 2 registers.
+ * bssidx 0 and 1 keys are stored in SEC_CSR1 and
+ * bssidx 1 and 2 keys are stored in SEC_CSR5.
+ * Using the correct defines correctly will cause overhead,
+ * so just calculate the correct offset.
+ */
+ if (key->hw_key_idx < 8) {
+ field.bit_offset = (3 * key->hw_key_idx);
+ field.bit_mask = 0x7 << field.bit_offset;
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR1, ®);
+ rt2x00_set_field32(®, field, crypto->cipher);
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR1, reg);
+ } else {
+ field.bit_offset = (3 * (key->hw_key_idx - 8));
+ field.bit_mask = 0x7 << field.bit_offset;
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR5, ®);
+ rt2x00_set_field32(®, field, crypto->cipher);
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR5, reg);
+ }
+
+ /*
+ * The driver does not support the IV/EIV generation
+ * in hardware. However it doesn't support the IV/EIV
+ * inside the ieee80211 frame either, but requires it
+ * to be provided seperately for the descriptor.
+ * rt2x00lib will cut the IV/EIV data out of all frames
+ * given to us by mac80211, but we must tell mac80211
+ * to generate the IV/EIV data.
+ */
+ key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
+ }
+
+ /*
+ * SEC_CSR0 contains only single-bit fields to indicate
+ * a particular key is valid. Because using the FIELD32()
+ * defines directly will cause a lot of overhead we use
+ * a calculation to determine the correct bit directly.
+ */
+ mask = 1 << key->hw_key_idx;
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR0, ®);
+ if (crypto->cmd == SET_KEY)
+ reg |= mask;
+ else if (crypto->cmd == DISABLE_KEY)
+ reg &= ~mask;
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR0, reg);
+
+ return 0;
+}
+
+static int rt61pci_config_pairwise_key(struct rt2x00_dev *rt2x00dev,
+ struct rt2x00lib_crypto *crypto,
+ struct ieee80211_key_conf *key)
+{
+ struct hw_pairwise_ta_entry addr_entry;
+ struct hw_key_entry key_entry;
+ u32 mask;
+ u32 reg;
+
+ if (crypto->cmd == SET_KEY) {
+ /*
+ * rt2x00lib can't determine the correct free
+ * key_idx for pairwise keys. We have 2 registers
+ * with key valid bits. The goal is simple, read
+ * the first register, if that is full move to
+ * the next register.
+ * When both registers are full, we drop the key,
+ * otherwise we use the first invalid entry.
+ */
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR2, ®);
+ if (reg && reg == ~0) {
+ key->hw_key_idx = 32;
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR3, ®);
+ if (reg && reg == ~0)
+ return -ENOSPC;
+ }
+
+ key->hw_key_idx += reg ? ffz(reg) : 0;
+
+ /*
+ * Upload key to hardware
+ */
+ memcpy(key_entry.key, crypto->key,
+ sizeof(key_entry.key));
+ memcpy(key_entry.tx_mic, crypto->tx_mic,
+ sizeof(key_entry.tx_mic));
+ memcpy(key_entry.rx_mic, crypto->rx_mic,
+ sizeof(key_entry.rx_mic));
+
+ memset(&addr_entry, 0, sizeof(addr_entry));
+ memcpy(&addr_entry, crypto->address, ETH_ALEN);
+ addr_entry.cipher = crypto->cipher;
+
+ reg = PAIRWISE_KEY_ENTRY(key->hw_key_idx);
+ rt2x00pci_register_multiwrite(rt2x00dev, reg,
+ &key_entry, sizeof(key_entry));
+
+ reg = PAIRWISE_TA_ENTRY(key->hw_key_idx);
+ rt2x00pci_register_multiwrite(rt2x00dev, reg,
+ &addr_entry, sizeof(addr_entry));
+
+ /*
+ * Enable pairwise lookup table for given BSS idx,
+ * without this received frames will not be decrypted
+ * by the hardware.
+ */
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR4, ®);
+ reg |= (1 << crypto->bssidx);
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR4, reg);
+
+ /*
+ * The driver does not support the IV/EIV generation
+ * in hardware. However it doesn't support the IV/EIV
+ * inside the ieee80211 frame either, but requires it
+ * to be provided seperately for the descriptor.
+ * rt2x00lib will cut the IV/EIV data out of all frames
+ * given to us by mac80211, but we must tell mac80211
+ * to generate the IV/EIV data.
+ */
+ key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
+ }
+
+ /*
+ * SEC_CSR2 and SEC_CSR3 contain only single-bit fields to indicate
+ * a particular key is valid. Because using the FIELD32()
+ * defines directly will cause a lot of overhead we use
+ * a calculation to determine the correct bit directly.
+ */
+ if (key->hw_key_idx < 32) {
+ mask = 1 << key->hw_key_idx;
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR2, ®);
+ if (crypto->cmd == SET_KEY)
+ reg |= mask;
+ else if (crypto->cmd == DISABLE_KEY)
+ reg &= ~mask;
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR2, reg);
+ } else {
+ mask = 1 << (key->hw_key_idx - 32);
+
+ rt2x00pci_register_read(rt2x00dev, SEC_CSR3, ®);
+ if (crypto->cmd == SET_KEY)
+ reg |= mask;
+ else if (crypto->cmd == DISABLE_KEY)
+ reg &= ~mask;
+ rt2x00pci_register_write(rt2x00dev, SEC_CSR3, reg);
+ }
+
+ return 0;
+}
+
static void rt61pci_config_filter(struct rt2x00_dev *rt2x00dev,
const unsigned int filter_flags)
{
rt2x00pci_register_write(rt2x00dev, TXRX_CSR4, reg);
}
+
+static void rt61pci_config_lna_gain(struct rt2x00_dev *rt2x00dev,
+ struct rt2x00lib_conf *libconf)
+{
+ u16 eeprom;
+ short lna_gain = 0;
+
+ if (libconf->band == IEEE80211_BAND_2GHZ) {
+ if (test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags))
+ lna_gain += 14;
+
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_BG, &eeprom);
+ lna_gain -= rt2x00_get_field16(eeprom, EEPROM_RSSI_OFFSET_BG_1);
+ } else {
+ if (test_bit(CONFIG_EXTERNAL_LNA_A, &rt2x00dev->flags))
+ lna_gain += 14;
+
+ rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_A, &eeprom);
+ lna_gain -= rt2x00_get_field16(eeprom, EEPROM_RSSI_OFFSET_A_1);
+ }
+
+ rt2x00dev->lna_gain = lna_gain;
+}
+
static void rt61pci_config_phymode(struct rt2x00_dev *rt2x00dev,
const int basic_rate_mask)
{
struct rt2x00lib_conf *libconf,
const unsigned int flags)
{
+ /* Always recalculate LNA gain before changing configuration */
+ rt61pci_config_lna_gain(rt2x00dev, libconf);
+
if (flags & CONFIG_UPDATE_PHYMODE)
rt61pci_config_phymode(rt2x00dev, libconf->basic_rates);
if (flags & CONFIG_UPDATE_CHANNEL)
rt2x00pci_register_write(rt2x00dev, M2H_CMD_DONE_CSR, 0xffffffff);
- rt2x00pci_register_read(rt2x00dev, AC_TXOP_CSR0, ®);
- rt2x00_set_field32(®, AC_TXOP_CSR0_AC0_TX_OP, 0);
- rt2x00_set_field32(®, AC_TXOP_CSR0_AC1_TX_OP, 0);
- rt2x00pci_register_write(rt2x00dev, AC_TXOP_CSR0, reg);
-
- rt2x00pci_register_read(rt2x00dev, AC_TXOP_CSR1, ®);
- rt2x00_set_field32(®, AC_TXOP_CSR1_AC2_TX_OP, 192);
- rt2x00_set_field32(®, AC_TXOP_CSR1_AC3_TX_OP, 48);
- rt2x00pci_register_write(rt2x00dev, AC_TXOP_CSR1, reg);
-
/*
* Clear all beacons
* For the Beacon base registers we only need to clear
* TX descriptor initialization
*/
static void rt61pci_write_tx_desc(struct rt2x00_dev *rt2x00dev,
- struct sk_buff *skb,
- struct txentry_desc *txdesc)
+ struct sk_buff *skb,
+ struct txentry_desc *txdesc)
{
struct skb_frame_desc *skbdesc = get_skb_frame_desc(skb);
__le32 *txd = skbdesc->desc;
rt2x00_set_field32(&word, TXD_W1_AIFSN, txdesc->aifs);
rt2x00_set_field32(&word, TXD_W1_CWMIN, txdesc->cw_min);
rt2x00_set_field32(&word, TXD_W1_CWMAX, txdesc->cw_max);
- rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, IEEE80211_HEADER);
+ rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, txdesc->iv_offset);
rt2x00_set_field32(&word, TXD_W1_HW_SEQUENCE,
test_bit(ENTRY_TXD_GENERATE_SEQ, &txdesc->flags));
rt2x00_set_field32(&word, TXD_W1_BUFFER_COUNT, 1);
rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_HIGH, txdesc->length_high);
rt2x00_desc_write(txd, 2, word);
+ if (test_bit(ENTRY_TXD_ENCRYPT, &txdesc->flags)) {
+ _rt2x00_desc_write(txd, 3, skbdesc->iv);
+ _rt2x00_desc_write(txd, 4, skbdesc->eiv);
+ }
+
rt2x00_desc_read(txd, 5, &word);
rt2x00_set_field32(&word, TXD_W5_PID_TYPE, skbdesc->entry->queue->qid);
rt2x00_set_field32(&word, TXD_W5_PID_SUBTYPE,
rt2x00_set_field32(&word, TXD_W0_IFS, txdesc->ifs);
rt2x00_set_field32(&word, TXD_W0_RETRY_MODE,
test_bit(ENTRY_TXD_RETRY_MODE, &txdesc->flags));
- rt2x00_set_field32(&word, TXD_W0_TKIP_MIC, 0);
+ rt2x00_set_field32(&word, TXD_W0_TKIP_MIC,
+ test_bit(ENTRY_TXD_ENCRYPT_MMIC, &txdesc->flags));
+ rt2x00_set_field32(&word, TXD_W0_KEY_TABLE,
+ test_bit(ENTRY_TXD_ENCRYPT_PAIRWISE, &txdesc->flags));
+ rt2x00_set_field32(&word, TXD_W0_KEY_INDEX, txdesc->key_idx);
rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, skb->len);
rt2x00_set_field32(&word, TXD_W0_BURST,
test_bit(ENTRY_TXD_BURST, &txdesc->flags));
- rt2x00_set_field32(&word, TXD_W0_CIPHER_ALG, CIPHER_NONE);
+ rt2x00_set_field32(&word, TXD_W0_CIPHER_ALG, txdesc->cipher);
rt2x00_desc_write(txd, 0, word);
}
*/
static int rt61pci_agc_to_rssi(struct rt2x00_dev *rt2x00dev, int rxd_w1)
{
- u16 eeprom;
- u8 offset;
+ u8 offset = rt2x00dev->lna_gain;
u8 lna;
lna = rt2x00_get_field32(rxd_w1, RXD_W1_RSSI_LNA);
switch (lna) {
case 3:
- offset = 90;
+ offset += 90;
break;
case 2:
- offset = 74;
+ offset += 74;
break;
case 1:
- offset = 64;
+ offset += 64;
break;
default:
return 0;
}
if (rt2x00dev->rx_status.band == IEEE80211_BAND_5GHZ) {
- if (test_bit(CONFIG_EXTERNAL_LNA_A, &rt2x00dev->flags))
- offset += 14;
-
if (lna == 3 || lna == 2)
offset += 10;
-
- rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_A, &eeprom);
- offset -= rt2x00_get_field16(eeprom, EEPROM_RSSI_OFFSET_A_1);
- } else {
- if (test_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags))
- offset += 14;
-
- rt2x00_eeprom_read(rt2x00dev, EEPROM_RSSI_OFFSET_BG, &eeprom);
- offset -= rt2x00_get_field16(eeprom, EEPROM_RSSI_OFFSET_BG_1);
}
return rt2x00_get_field32(rxd_w1, RXD_W1_RSSI_AGC) * 2 - offset;
static void rt61pci_fill_rxdone(struct queue_entry *entry,
struct rxdone_entry_desc *rxdesc)
{
+ struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
struct queue_entry_priv_pci *entry_priv = entry->priv_data;
u32 word0;
u32 word1;
if (rt2x00_get_field32(word0, RXD_W0_CRC_ERROR))
rxdesc->flags |= RX_FLAG_FAILED_FCS_CRC;
+ if (test_bit(CONFIG_SUPPORT_HW_CRYPTO, &rt2x00dev->flags)) {
+ rxdesc->cipher =
+ rt2x00_get_field32(word0, RXD_W0_CIPHER_ALG);
+ rxdesc->cipher_status =
+ rt2x00_get_field32(word0, RXD_W0_CIPHER_ERROR);
+ }
+
+ if (rxdesc->cipher != CIPHER_NONE) {
+ _rt2x00_desc_read(entry_priv->desc, 2, &rxdesc->iv);
+ _rt2x00_desc_read(entry_priv->desc, 3, &rxdesc->eiv);
+ _rt2x00_desc_read(entry_priv->desc, 4, &rxdesc->icv);
+
+ /*
+ * Hardware has stripped IV/EIV data from 802.11 frame during
+ * decryption. It has provided the data seperately but rt2x00lib
+ * should decide if it should be reinserted.
+ */
+ rxdesc->flags |= RX_FLAG_IV_STRIPPED;
+
+ /*
+ * FIXME: Legacy driver indicates that the frame does
+ * contain the Michael Mic. Unfortunately, in rt2x00
+ * the MIC seems to be missing completely...
+ */
+ rxdesc->flags |= RX_FLAG_MMIC_STRIPPED;
+
+ if (rxdesc->cipher_status == RX_CRYPTO_SUCCESS)
+ rxdesc->flags |= RX_FLAG_DECRYPTED;
+ else if (rxdesc->cipher_status == RX_CRYPTO_FAIL_MIC)
+ rxdesc->flags |= RX_FLAG_MMIC_ERROR;
+ }
+
/*
* Obtain the status about this packet.
* When frame was received with an OFDM bitrate,
* a CCK bitrate the signal is the rate in 100kbit/s.
*/
rxdesc->signal = rt2x00_get_field32(word1, RXD_W1_SIGNAL);
- rxdesc->rssi = rt61pci_agc_to_rssi(entry->queue->rt2x00dev, word1);
+ rxdesc->rssi = rt61pci_agc_to_rssi(rt2x00dev, word1);
rxdesc->size = rt2x00_get_field32(word0, RXD_W0_DATABYTE_COUNT);
if (rt2x00_get_field32(word0, RXD_W0_OFDM))
rxdesc->dev_flags |= RXDONE_SIGNAL_PLCP;
+ else
+ rxdesc->dev_flags |= RXDONE_SIGNAL_BITRATE;
if (rt2x00_get_field32(word0, RXD_W0_MY_BSS))
rxdesc->dev_flags |= RXDONE_MY_BSS;
}
if (!reg && !reg_mcu)
return IRQ_NONE;
- if (!test_bit(DEVICE_ENABLED_RADIO, &rt2x00dev->flags))
+ if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags))
return IRQ_HANDLED;
/*
/*
* Detect if this device has an hardware controlled radio.
*/
-#ifdef CONFIG_RT61PCI_RFKILL
+#ifdef CONFIG_RT2X00_LIB_RFKILL
if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_HARDWARE_RADIO))
__set_bit(CONFIG_SUPPORT_HW_BUTTON, &rt2x00dev->flags);
-#endif /* CONFIG_RT61PCI_RFKILL */
+#endif /* CONFIG_RT2X00_LIB_RFKILL */
/*
* Read frequency offset and RF programming sequence.
* If the eeprom value is invalid,
* switch to default led mode.
*/
-#ifdef CONFIG_RT61PCI_LEDS
+#ifdef CONFIG_RT2X00_LIB_LEDS
rt2x00_eeprom_read(rt2x00dev, EEPROM_LED, &eeprom);
value = rt2x00_get_field16(eeprom, EEPROM_LED_LED_MODE);
rt2x00_set_field16(&rt2x00dev->led_mcu_reg, MCU_LEDCS_POLARITY_READY_A,
rt2x00_get_field16(eeprom,
EEPROM_LED_POLARITY_RDY_A));
-#endif /* CONFIG_RT61PCI_LEDS */
+#endif /* CONFIG_RT2X00_LIB_LEDS */
return 0;
}
{ 46, 0x00002ccc, 0x000049a6, 0x0009be55, 0x000c0a23 },
};
-static void rt61pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev)
+static int rt61pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev)
{
struct hw_mode_spec *spec = &rt2x00dev->spec;
- u8 *txpower;
+ struct channel_info *info;
+ char *tx_power;
unsigned int i;
/*
rt2x00_eeprom_addr(rt2x00dev,
EEPROM_MAC_ADDR_0));
- /*
- * Convert tx_power array in eeprom.
- */
- txpower = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_G_START);
- for (i = 0; i < 14; i++)
- txpower[i] = TXPOWER_FROM_DEV(txpower[i]);
-
/*
* Initialize hw_mode information.
*/
spec->supported_bands = SUPPORT_BAND_2GHZ;
spec->supported_rates = SUPPORT_RATE_CCK | SUPPORT_RATE_OFDM;
- spec->tx_power_a = NULL;
- spec->tx_power_bg = txpower;
- spec->tx_power_default = DEFAULT_TXPOWER;
if (!test_bit(CONFIG_RF_SEQUENCE, &rt2x00dev->flags)) {
spec->num_channels = 14;
rt2x00_rf(&rt2x00dev->chip, RF5325)) {
spec->supported_bands |= SUPPORT_BAND_5GHZ;
spec->num_channels = ARRAY_SIZE(rf_vals_seq);
+ }
- txpower = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_A_START);
- for (i = 0; i < 14; i++)
- txpower[i] = TXPOWER_FROM_DEV(txpower[i]);
+ /*
+ * Create channel information array
+ */
+ info = kzalloc(spec->num_channels * sizeof(*info), GFP_KERNEL);
+ if (!info)
+ return -ENOMEM;
- spec->tx_power_a = txpower;
+ spec->channels_info = info;
+
+ tx_power = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_G_START);
+ for (i = 0; i < 14; i++)
+ info[i].tx_power1 = TXPOWER_FROM_DEV(tx_power[i]);
+
+ if (spec->num_channels > 14) {
+ tx_power = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_A_START);
+ for (i = 14; i < spec->num_channels; i++)
+ info[i].tx_power1 = TXPOWER_FROM_DEV(tx_power[i]);
}
+
+ return 0;
}
static int rt61pci_probe_hw(struct rt2x00_dev *rt2x00dev)
/*
* Initialize hw specifications.
*/
- rt61pci_probe_hw_mode(rt2x00dev);
+ retval = rt61pci_probe_hw_mode(rt2x00dev);
+ if (retval)
+ return retval;
/*
* This device requires firmware and DMA mapped skbs.
*/
__set_bit(DRIVER_REQUIRE_FIRMWARE, &rt2x00dev->flags);
__set_bit(DRIVER_REQUIRE_DMA, &rt2x00dev->flags);
+ if (!modparam_nohwcrypt)
+ __set_bit(CONFIG_SUPPORT_HW_CRYPTO, &rt2x00dev->flags);
/*
* Set the rssi offset.
return 0;
}
+static int rt61pci_conf_tx(struct ieee80211_hw *hw, u16 queue_idx,
+ const struct ieee80211_tx_queue_params *params)
+{
+ struct rt2x00_dev *rt2x00dev = hw->priv;
+ struct data_queue *queue;
+ struct rt2x00_field32 field;
+ int retval;
+ u32 reg;
+
+ /*
+ * First pass the configuration through rt2x00lib, that will
+ * update the queue settings and validate the input. After that
+ * we are free to update the registers based on the value
+ * in the queue parameter.
+ */
+ retval = rt2x00mac_conf_tx(hw, queue_idx, params);
+ if (retval)
+ return retval;
+
+ queue = rt2x00queue_get_queue(rt2x00dev, queue_idx);
+
+ /* Update WMM TXOP register */
+ if (queue_idx < 2) {
+ field.bit_offset = queue_idx * 16;
+ field.bit_mask = 0xffff << field.bit_offset;
+
+ rt2x00pci_register_read(rt2x00dev, AC_TXOP_CSR0, ®);
+ rt2x00_set_field32(®, field, queue->txop);
+ rt2x00pci_register_write(rt2x00dev, AC_TXOP_CSR0, reg);
+ } else if (queue_idx < 4) {
+ field.bit_offset = (queue_idx - 2) * 16;
+ field.bit_mask = 0xffff << field.bit_offset;
+
+ rt2x00pci_register_read(rt2x00dev, AC_TXOP_CSR1, ®);
+ rt2x00_set_field32(®, field, queue->txop);
+ rt2x00pci_register_write(rt2x00dev, AC_TXOP_CSR1, reg);
+ }
+
+ /* Update WMM registers */
+ field.bit_offset = queue_idx * 4;
+ field.bit_mask = 0xf << field.bit_offset;
+
+ rt2x00pci_register_read(rt2x00dev, AIFSN_CSR, ®);
+ rt2x00_set_field32(®, field, queue->aifs);
+ rt2x00pci_register_write(rt2x00dev, AIFSN_CSR, reg);
+
+ rt2x00pci_register_read(rt2x00dev, CWMIN_CSR, ®);
+ rt2x00_set_field32(®, field, queue->cw_min);
+ rt2x00pci_register_write(rt2x00dev, CWMIN_CSR, reg);
+
+ rt2x00pci_register_read(rt2x00dev, CWMAX_CSR, ®);
+ rt2x00_set_field32(®, field, queue->cw_max);
+ rt2x00pci_register_write(rt2x00dev, CWMAX_CSR, reg);
+
+ return 0;
+}
+
static u64 rt61pci_get_tsf(struct ieee80211_hw *hw)
{
struct rt2x00_dev *rt2x00dev = hw->priv;
.config = rt2x00mac_config,
.config_interface = rt2x00mac_config_interface,
.configure_filter = rt2x00mac_configure_filter,
+ .set_key = rt2x00mac_set_key,
.get_stats = rt2x00mac_get_stats,
.set_retry_limit = rt61pci_set_retry_limit,
.bss_info_changed = rt2x00mac_bss_info_changed,
- .conf_tx = rt2x00mac_conf_tx,
+ .conf_tx = rt61pci_conf_tx,
.get_tx_stats = rt2x00mac_get_tx_stats,
.get_tsf = rt61pci_get_tsf,
};
.write_beacon = rt61pci_write_beacon,
.kick_tx_queue = rt61pci_kick_tx_queue,
.fill_rxdone = rt61pci_fill_rxdone,
+ .config_shared_key = rt61pci_config_shared_key,
+ .config_pairwise_key = rt61pci_config_pairwise_key,
.config_filter = rt61pci_config_filter,
.config_intf = rt61pci_config_intf,
.config_erp = rt61pci_config_erp,
git.openpandora.org / pandora-kernel.git / blobdiff