*/
#include <linux/slab.h>
+#include <linux/sched.h>
+#include <linux/wait.h>
+#include <linux/ieee80211.h>
#include <net/cfg80211.h>
+#include <asm/unaligned.h>
+#include "decl.h"
#include "cfg.h"
#include "cmd.h"
CHAN2G(14, 2484, 0),
};
-#define RATETAB_ENT(_rate, _rateid, _flags) { \
- .bitrate = (_rate), \
- .hw_value = (_rateid), \
- .flags = (_flags), \
+#define RATETAB_ENT(_rate, _hw_value, _flags) { \
+ .bitrate = (_rate), \
+ .hw_value = (_hw_value), \
+ .flags = (_flags), \
}
+/* Table 6 in section 3.2.1.1 */
static struct ieee80211_rate lbs_rates[] = {
- RATETAB_ENT(10, 0x1, 0),
- RATETAB_ENT(20, 0x2, 0),
- RATETAB_ENT(55, 0x4, 0),
- RATETAB_ENT(110, 0x8, 0),
- RATETAB_ENT(60, 0x10, 0),
- RATETAB_ENT(90, 0x20, 0),
- RATETAB_ENT(120, 0x40, 0),
- RATETAB_ENT(180, 0x80, 0),
- RATETAB_ENT(240, 0x100, 0),
- RATETAB_ENT(360, 0x200, 0),
- RATETAB_ENT(480, 0x400, 0),
- RATETAB_ENT(540, 0x800, 0),
+ RATETAB_ENT(10, 0, 0),
+ RATETAB_ENT(20, 1, 0),
+ RATETAB_ENT(55, 2, 0),
+ RATETAB_ENT(110, 3, 0),
+ RATETAB_ENT(60, 9, 0),
+ RATETAB_ENT(90, 6, 0),
+ RATETAB_ENT(120, 7, 0),
+ RATETAB_ENT(180, 8, 0),
+ RATETAB_ENT(240, 9, 0),
+ RATETAB_ENT(360, 10, 0),
+ RATETAB_ENT(480, 11, 0),
+ RATETAB_ENT(540, 12, 0),
};
static struct ieee80211_supported_band lbs_band_2ghz = {
WLAN_CIPHER_SUITE_CCMP,
};
+/* Time to stay on the channel */
+#define LBS_DWELL_PASSIVE 100
+#define LBS_DWELL_ACTIVE 40
+/***************************************************************************
+ * Misc utility functions
+ *
+ * TLVs are Marvell specific. They are very similar to IEs, they have the
+ * same structure: type, length, data*. The only difference: for IEs, the
+ * type and length are u8, but for TLVs they're __le16.
+ */
+
+/*
+ * Convert NL80211's auth_type to the one from Libertas, see chapter 5.9.1
+ * in the firmware spec
+ */
+static u8 lbs_auth_to_authtype(enum nl80211_auth_type auth_type)
+{
+ int ret = -ENOTSUPP;
+
+ switch (auth_type) {
+ case NL80211_AUTHTYPE_OPEN_SYSTEM:
+ case NL80211_AUTHTYPE_SHARED_KEY:
+ ret = auth_type;
+ break;
+ case NL80211_AUTHTYPE_AUTOMATIC:
+ ret = NL80211_AUTHTYPE_OPEN_SYSTEM;
+ break;
+ case NL80211_AUTHTYPE_NETWORK_EAP:
+ ret = 0x80;
+ break;
+ default:
+ /* silence compiler */
+ break;
+ }
+ return ret;
+}
+
+
+/* Various firmware commands need the list of supported rates, but with
+ the hight-bit set for basic rates */
+static int lbs_add_rates(u8 *rates)
+{
+ size_t i;
+
+ for (i = 0; i < ARRAY_SIZE(lbs_rates); i++) {
+ u8 rate = lbs_rates[i].bitrate / 5;
+ if (rate == 0x02 || rate == 0x04 ||
+ rate == 0x0b || rate == 0x16)
+ rate |= 0x80;
+ rates[i] = rate;
+ }
+ return ARRAY_SIZE(lbs_rates);
+}
+
+
+/***************************************************************************
+ * TLV utility functions
+ *
+ * TLVs are Marvell specific. They are very similar to IEs, they have the
+ * same structure: type, length, data*. The only difference: for IEs, the
+ * type and length are u8, but for TLVs they're __le16.
+ */
+
+
+/*
+ * Add ssid TLV
+ */
+#define LBS_MAX_SSID_TLV_SIZE \
+ (sizeof(struct mrvl_ie_header) \
+ + IEEE80211_MAX_SSID_LEN)
+
+static int lbs_add_ssid_tlv(u8 *tlv, const u8 *ssid, int ssid_len)
+{
+ struct mrvl_ie_ssid_param_set *ssid_tlv = (void *)tlv;
+
+ /*
+ * TLV-ID SSID 00 00
+ * length 06 00
+ * ssid 4d 4e 54 45 53 54
+ */
+ ssid_tlv->header.type = cpu_to_le16(TLV_TYPE_SSID);
+ ssid_tlv->header.len = cpu_to_le16(ssid_len);
+ memcpy(ssid_tlv->ssid, ssid, ssid_len);
+ return sizeof(ssid_tlv->header) + ssid_len;
+}
+
+
+/*
+ * Add channel list TLV (section 8.4.2)
+ *
+ * Actual channel data comes from priv->wdev->wiphy->channels.
+ */
+#define LBS_MAX_CHANNEL_LIST_TLV_SIZE \
+ (sizeof(struct mrvl_ie_header) \
+ + (LBS_SCAN_BEFORE_NAP * sizeof(struct chanscanparamset)))
+
+static int lbs_add_channel_list_tlv(struct lbs_private *priv, u8 *tlv,
+ int last_channel, int active_scan)
+{
+ int chanscanparamsize = sizeof(struct chanscanparamset) *
+ (last_channel - priv->scan_channel);
+
+ struct mrvl_ie_header *header = (void *) tlv;
+
+ /*
+ * TLV-ID CHANLIST 01 01
+ * length 0e 00
+ * channel 00 01 00 00 00 64 00
+ * radio type 00
+ * channel 01
+ * scan type 00
+ * min scan time 00 00
+ * max scan time 64 00
+ * channel 2 00 02 00 00 00 64 00
+ *
+ */
+
+ header->type = cpu_to_le16(TLV_TYPE_CHANLIST);
+ header->len = cpu_to_le16(chanscanparamsize);
+ tlv += sizeof(struct mrvl_ie_header);
+
+ /* lbs_deb_scan("scan: channels %d to %d\n", priv->scan_channel,
+ last_channel); */
+ memset(tlv, 0, chanscanparamsize);
+
+ while (priv->scan_channel < last_channel) {
+ struct chanscanparamset *param = (void *) tlv;
+
+ param->radiotype = CMD_SCAN_RADIO_TYPE_BG;
+ param->channumber =
+ priv->scan_req->channels[priv->scan_channel]->hw_value;
+ if (active_scan) {
+ param->maxscantime = cpu_to_le16(LBS_DWELL_ACTIVE);
+ } else {
+ param->chanscanmode.passivescan = 1;
+ param->maxscantime = cpu_to_le16(LBS_DWELL_PASSIVE);
+ }
+ tlv += sizeof(struct chanscanparamset);
+ priv->scan_channel++;
+ }
+ return sizeof(struct mrvl_ie_header) + chanscanparamsize;
+}
+
+
+/*
+ * Add rates TLV
+ *
+ * The rates are in lbs_bg_rates[], but for the 802.11b
+ * rates the high bit is set. We add this TLV only because
+ * there's a firmware which otherwise doesn't report all
+ * APs in range.
+ */
+#define LBS_MAX_RATES_TLV_SIZE \
+ (sizeof(struct mrvl_ie_header) \
+ + (ARRAY_SIZE(lbs_rates)))
+
+/* Adds a TLV with all rates the hardware supports */
+static int lbs_add_supported_rates_tlv(u8 *tlv)
+{
+ size_t i;
+ struct mrvl_ie_rates_param_set *rate_tlv = (void *)tlv;
+
+ /*
+ * TLV-ID RATES 01 00
+ * length 0e 00
+ * rates 82 84 8b 96 0c 12 18 24 30 48 60 6c
+ */
+ rate_tlv->header.type = cpu_to_le16(TLV_TYPE_RATES);
+ tlv += sizeof(rate_tlv->header);
+ i = lbs_add_rates(tlv);
+ tlv += i;
+ rate_tlv->header.len = cpu_to_le16(i);
+ return sizeof(rate_tlv->header) + i;
+}
+
+/* Add common rates from a TLV and return the new end of the TLV */
+static u8 *
+add_ie_rates(u8 *tlv, const u8 *ie, int *nrates)
+{
+ int hw, ap, ap_max = ie[1];
+ u8 hw_rate;
+
+ /* Advance past IE header */
+ ie += 2;
+
+ lbs_deb_hex(LBS_DEB_ASSOC, "AP IE Rates", (u8 *) ie, ap_max);
+
+ for (hw = 0; hw < ARRAY_SIZE(lbs_rates); hw++) {
+ hw_rate = lbs_rates[hw].bitrate / 5;
+ for (ap = 0; ap < ap_max; ap++) {
+ if (hw_rate == (ie[ap] & 0x7f)) {
+ *tlv++ = ie[ap];
+ *nrates = *nrates + 1;
+ }
+ }
+ }
+ return tlv;
+}
+
+/*
+ * Adds a TLV with all rates the hardware *and* BSS supports.
+ */
+static int lbs_add_common_rates_tlv(u8 *tlv, struct cfg80211_bss *bss)
+{
+ struct mrvl_ie_rates_param_set *rate_tlv = (void *)tlv;
+ const u8 *rates_eid, *ext_rates_eid;
+ int n = 0;
+
+ rates_eid = ieee80211_bss_get_ie(bss, WLAN_EID_SUPP_RATES);
+ ext_rates_eid = ieee80211_bss_get_ie(bss, WLAN_EID_EXT_SUPP_RATES);
+
+ /*
+ * 01 00 TLV_TYPE_RATES
+ * 04 00 len
+ * 82 84 8b 96 rates
+ */
+ rate_tlv->header.type = cpu_to_le16(TLV_TYPE_RATES);
+ tlv += sizeof(rate_tlv->header);
+
+ /* Add basic rates */
+ if (rates_eid) {
+ tlv = add_ie_rates(tlv, rates_eid, &n);
+
+ /* Add extended rates, if any */
+ if (ext_rates_eid)
+ tlv = add_ie_rates(tlv, ext_rates_eid, &n);
+ } else {
+ lbs_deb_assoc("assoc: bss had no basic rate IE\n");
+ /* Fallback: add basic 802.11b rates */
+ *tlv++ = 0x82;
+ *tlv++ = 0x84;
+ *tlv++ = 0x8b;
+ *tlv++ = 0x96;
+ n = 4;
+ }
+
+ rate_tlv->header.len = cpu_to_le16(n);
+ return sizeof(rate_tlv->header) + n;
+}
+
+
+/*
+ * Add auth type TLV.
+ *
+ * This is only needed for newer firmware (V9 and up).
+ */
+#define LBS_MAX_AUTH_TYPE_TLV_SIZE \
+ sizeof(struct mrvl_ie_auth_type)
+
+static int lbs_add_auth_type_tlv(u8 *tlv, enum nl80211_auth_type auth_type)
+{
+ struct mrvl_ie_auth_type *auth = (void *) tlv;
+
+ /*
+ * 1f 01 TLV_TYPE_AUTH_TYPE
+ * 01 00 len
+ * 01 auth type
+ */
+ auth->header.type = cpu_to_le16(TLV_TYPE_AUTH_TYPE);
+ auth->header.len = cpu_to_le16(sizeof(*auth)-sizeof(auth->header));
+ auth->auth = cpu_to_le16(lbs_auth_to_authtype(auth_type));
+ return sizeof(*auth);
+}
+
+
+/*
+ * Add channel (phy ds) TLV
+ */
+#define LBS_MAX_CHANNEL_TLV_SIZE \
+ sizeof(struct mrvl_ie_header)
+
+static int lbs_add_channel_tlv(u8 *tlv, u8 channel)
+{
+ struct mrvl_ie_ds_param_set *ds = (void *) tlv;
+
+ /*
+ * 03 00 TLV_TYPE_PHY_DS
+ * 01 00 len
+ * 06 channel
+ */
+ ds->header.type = cpu_to_le16(TLV_TYPE_PHY_DS);
+ ds->header.len = cpu_to_le16(sizeof(*ds)-sizeof(ds->header));
+ ds->channel = channel;
+ return sizeof(*ds);
+}
+
+
+/*
+ * Add (empty) CF param TLV of the form:
+ */
+#define LBS_MAX_CF_PARAM_TLV_SIZE \
+ sizeof(struct mrvl_ie_header)
+
+static int lbs_add_cf_param_tlv(u8 *tlv)
+{
+ struct mrvl_ie_cf_param_set *cf = (void *)tlv;
+
+ /*
+ * 04 00 TLV_TYPE_CF
+ * 06 00 len
+ * 00 cfpcnt
+ * 00 cfpperiod
+ * 00 00 cfpmaxduration
+ * 00 00 cfpdurationremaining
+ */
+ cf->header.type = cpu_to_le16(TLV_TYPE_CF);
+ cf->header.len = cpu_to_le16(sizeof(*cf)-sizeof(cf->header));
+ return sizeof(*cf);
+}
+
+/*
+ * Add WPA TLV
+ */
+#define LBS_MAX_WPA_TLV_SIZE \
+ (sizeof(struct mrvl_ie_header) \
+ + 128 /* TODO: I guessed the size */)
+
+static int lbs_add_wpa_tlv(u8 *tlv, const u8 *ie, u8 ie_len)
+{
+ size_t tlv_len;
+
+ /*
+ * We need just convert an IE to an TLV. IEs use u8 for the header,
+ * u8 type
+ * u8 len
+ * u8[] data
+ * but TLVs use __le16 instead:
+ * __le16 type
+ * __le16 len
+ * u8[] data
+ */
+ *tlv++ = *ie++;
+ *tlv++ = 0;
+ tlv_len = *tlv++ = *ie++;
+ *tlv++ = 0;
+ while (tlv_len--)
+ *tlv++ = *ie++;
+ /* the TLV is two bytes larger than the IE */
+ return ie_len + 2;
+}
+
+/***************************************************************************
+ * Set Channel
+ */
+
static int lbs_cfg_set_channel(struct wiphy *wiphy,
- struct ieee80211_channel *chan,
+ struct net_device *netdev,
+ struct ieee80211_channel *channel,
enum nl80211_channel_type channel_type)
{
struct lbs_private *priv = wiphy_priv(wiphy);
- int ret = -ENOTSUPP;
+ int ret = -ENOTSUPP;
+
+ lbs_deb_enter_args(LBS_DEB_CFG80211, "freq %d, type %d",
+ channel->center_freq, channel_type);
+
+ if (channel_type != NL80211_CHAN_NO_HT)
+ goto out;
+
+ ret = lbs_set_channel(priv, channel->hw_value);
+
+ out:
+ lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
+ return ret;
+}
+
+
+
+/***************************************************************************
+ * Scanning
+ */
+
+/*
+ * When scanning, the firmware doesn't send a nul packet with the power-safe
+ * bit to the AP. So we cannot stay away from our current channel too long,
+ * otherwise we loose data. So take a "nap" while scanning every other
+ * while.
+ */
+#define LBS_SCAN_BEFORE_NAP 4
+
+
+/*
+ * When the firmware reports back a scan-result, it gives us an "u8 rssi",
+ * which isn't really an RSSI, as it becomes larger when moving away from
+ * the AP. Anyway, we need to convert that into mBm.
+ */
+#define LBS_SCAN_RSSI_TO_MBM(rssi) \
+ ((-(int)rssi + 3)*100)
+
+static int lbs_ret_scan(struct lbs_private *priv, unsigned long dummy,
+ struct cmd_header *resp)
+{
+ struct cmd_ds_802_11_scan_rsp *scanresp = (void *)resp;
+ int bsssize;
+ const u8 *pos;
+ const u8 *tsfdesc;
+ int tsfsize;
+ int i;
+ int ret = -EILSEQ;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ bsssize = get_unaligned_le16(&scanresp->bssdescriptsize);
+
+ lbs_deb_scan("scan response: %d BSSs (%d bytes); resp size %d bytes\n",
+ scanresp->nr_sets, bsssize, le16_to_cpu(resp->size));
+
+ if (scanresp->nr_sets == 0) {
+ ret = 0;
+ goto done;
+ }
+
+ /*
+ * The general layout of the scan response is described in chapter
+ * 5.7.1. Basically we have a common part, then any number of BSS
+ * descriptor sections. Finally we have section with the same number
+ * of TSFs.
+ *
+ * cmd_ds_802_11_scan_rsp
+ * cmd_header
+ * pos_size
+ * nr_sets
+ * bssdesc 1
+ * bssid
+ * rssi
+ * timestamp
+ * intvl
+ * capa
+ * IEs
+ * bssdesc 2
+ * bssdesc n
+ * MrvlIEtypes_TsfFimestamp_t
+ * TSF for BSS 1
+ * TSF for BSS 2
+ * TSF for BSS n
+ */
+
+ pos = scanresp->bssdesc_and_tlvbuffer;
+
+ lbs_deb_hex(LBS_DEB_SCAN, "SCAN_RSP", scanresp->bssdesc_and_tlvbuffer,
+ scanresp->bssdescriptsize);
+
+ tsfdesc = pos + bsssize;
+ tsfsize = 4 + 8 * scanresp->nr_sets;
+ lbs_deb_hex(LBS_DEB_SCAN, "SCAN_TSF", (u8 *) tsfdesc, tsfsize);
+
+ /* Validity check: we expect a Marvell-Local TLV */
+ i = get_unaligned_le16(tsfdesc);
+ tsfdesc += 2;
+ if (i != TLV_TYPE_TSFTIMESTAMP) {
+ lbs_deb_scan("scan response: invalid TSF Timestamp %d\n", i);
+ goto done;
+ }
+
+ /* Validity check: the TLV holds TSF values with 8 bytes each, so
+ * the size in the TLV must match the nr_sets value */
+ i = get_unaligned_le16(tsfdesc);
+ tsfdesc += 2;
+ if (i / 8 != scanresp->nr_sets) {
+ lbs_deb_scan("scan response: invalid number of TSF timestamp "
+ "sets (expected %d got %d)\n", scanresp->nr_sets,
+ i / 8);
+ goto done;
+ }
+
+ for (i = 0; i < scanresp->nr_sets; i++) {
+ const u8 *bssid;
+ const u8 *ie;
+ int left;
+ int ielen;
+ int rssi;
+ u16 intvl;
+ u16 capa;
+ int chan_no = -1;
+ const u8 *ssid = NULL;
+ u8 ssid_len = 0;
+ DECLARE_SSID_BUF(ssid_buf);
+
+ int len = get_unaligned_le16(pos);
+ pos += 2;
+
+ /* BSSID */
+ bssid = pos;
+ pos += ETH_ALEN;
+ /* RSSI */
+ rssi = *pos++;
+ /* Packet time stamp */
+ pos += 8;
+ /* Beacon interval */
+ intvl = get_unaligned_le16(pos);
+ pos += 2;
+ /* Capabilities */
+ capa = get_unaligned_le16(pos);
+ pos += 2;
+
+ /* To find out the channel, we must parse the IEs */
+ ie = pos;
+ /* 6+1+8+2+2: size of BSSID, RSSI, time stamp, beacon
+ interval, capabilities */
+ ielen = left = len - (6 + 1 + 8 + 2 + 2);
+ while (left >= 2) {
+ u8 id, elen;
+ id = *pos++;
+ elen = *pos++;
+ left -= 2;
+ if (elen > left || elen == 0) {
+ lbs_deb_scan("scan response: invalid IE fmt\n");
+ goto done;
+ }
+
+ if (id == WLAN_EID_DS_PARAMS)
+ chan_no = *pos;
+ if (id == WLAN_EID_SSID) {
+ ssid = pos;
+ ssid_len = elen;
+ }
+ left -= elen;
+ pos += elen;
+ }
+
+ /* No channel, no luck */
+ if (chan_no != -1) {
+ struct wiphy *wiphy = priv->wdev->wiphy;
+ int freq = ieee80211_channel_to_frequency(chan_no);
+ struct ieee80211_channel *channel =
+ ieee80211_get_channel(wiphy, freq);
+
+ lbs_deb_scan("scan: %pM, capa %04x, chan %2d, %s, "
+ "%d dBm\n",
+ bssid, capa, chan_no,
+ print_ssid(ssid_buf, ssid, ssid_len),
+ LBS_SCAN_RSSI_TO_MBM(rssi)/100);
+
+ if (channel ||
+ !(channel->flags & IEEE80211_CHAN_DISABLED))
+ cfg80211_inform_bss(wiphy, channel,
+ bssid, le64_to_cpu(*(__le64 *)tsfdesc),
+ capa, intvl, ie, ielen,
+ LBS_SCAN_RSSI_TO_MBM(rssi),
+ GFP_KERNEL);
+ } else
+ lbs_deb_scan("scan response: missing BSS channel IE\n");
+
+ tsfdesc += 8;
+ }
+ ret = 0;
+
+ done:
+ lbs_deb_leave_args(LBS_DEB_SCAN, "ret %d", ret);
+ return ret;
+}
+
+
+/*
+ * Our scan command contains a TLV, consting of a SSID TLV, a channel list
+ * TLV and a rates TLV. Determine the maximum size of them:
+ */
+#define LBS_SCAN_MAX_CMD_SIZE \
+ (sizeof(struct cmd_ds_802_11_scan) \
+ + LBS_MAX_SSID_TLV_SIZE \
+ + LBS_MAX_CHANNEL_LIST_TLV_SIZE \
+ + LBS_MAX_RATES_TLV_SIZE)
+
+/*
+ * Assumes priv->scan_req is initialized and valid
+ * Assumes priv->scan_channel is initialized
+ */
+static void lbs_scan_worker(struct work_struct *work)
+{
+ struct lbs_private *priv =
+ container_of(work, struct lbs_private, scan_work.work);
+ struct cmd_ds_802_11_scan *scan_cmd;
+ u8 *tlv; /* pointer into our current, growing TLV storage area */
+ int last_channel;
+ int running, carrier;
+
+ lbs_deb_enter(LBS_DEB_SCAN);
+
+ scan_cmd = kzalloc(LBS_SCAN_MAX_CMD_SIZE, GFP_KERNEL);
+ if (scan_cmd == NULL)
+ goto out_no_scan_cmd;
+
+ /* prepare fixed part of scan command */
+ scan_cmd->bsstype = CMD_BSS_TYPE_ANY;
+
+ /* stop network while we're away from our main channel */
+ running = !netif_queue_stopped(priv->dev);
+ carrier = netif_carrier_ok(priv->dev);
+ if (running)
+ netif_stop_queue(priv->dev);
+ if (carrier)
+ netif_carrier_off(priv->dev);
+
+ /* prepare fixed part of scan command */
+ tlv = scan_cmd->tlvbuffer;
+
+ /* add SSID TLV */
+ if (priv->scan_req->n_ssids)
+ tlv += lbs_add_ssid_tlv(tlv,
+ priv->scan_req->ssids[0].ssid,
+ priv->scan_req->ssids[0].ssid_len);
+
+ /* add channel TLVs */
+ last_channel = priv->scan_channel + LBS_SCAN_BEFORE_NAP;
+ if (last_channel > priv->scan_req->n_channels)
+ last_channel = priv->scan_req->n_channels;
+ tlv += lbs_add_channel_list_tlv(priv, tlv, last_channel,
+ priv->scan_req->n_ssids);
+
+ /* add rates TLV */
+ tlv += lbs_add_supported_rates_tlv(tlv);
+
+ if (priv->scan_channel < priv->scan_req->n_channels) {
+ cancel_delayed_work(&priv->scan_work);
+ queue_delayed_work(priv->work_thread, &priv->scan_work,
+ msecs_to_jiffies(300));
+ }
+
+ /* This is the final data we are about to send */
+ scan_cmd->hdr.size = cpu_to_le16(tlv - (u8 *)scan_cmd);
+ lbs_deb_hex(LBS_DEB_SCAN, "SCAN_CMD", (void *)scan_cmd,
+ sizeof(*scan_cmd));
+ lbs_deb_hex(LBS_DEB_SCAN, "SCAN_TLV", scan_cmd->tlvbuffer,
+ tlv - scan_cmd->tlvbuffer);
+
+ __lbs_cmd(priv, CMD_802_11_SCAN, &scan_cmd->hdr,
+ le16_to_cpu(scan_cmd->hdr.size),
+ lbs_ret_scan, 0);
+
+ if (priv->scan_channel >= priv->scan_req->n_channels) {
+ /* Mark scan done */
+ if (priv->internal_scan)
+ kfree(priv->scan_req);
+ else
+ cfg80211_scan_done(priv->scan_req, false);
+
+ priv->scan_req = NULL;
+ priv->last_scan = jiffies;
+ }
+
+ /* Restart network */
+ if (carrier)
+ netif_carrier_on(priv->dev);
+ if (running && !priv->tx_pending_len)
+ netif_wake_queue(priv->dev);
+
+ kfree(scan_cmd);
+
+ /* Wake up anything waiting on scan completion */
+ if (priv->scan_req == NULL) {
+ lbs_deb_scan("scan: waking up waiters\n");
+ wake_up_all(&priv->scan_q);
+ }
+
+ out_no_scan_cmd:
+ lbs_deb_leave(LBS_DEB_SCAN);
+}
+
+static void _internal_start_scan(struct lbs_private *priv, bool internal,
+ struct cfg80211_scan_request *request)
+{
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ lbs_deb_scan("scan: ssids %d, channels %d, ie_len %zd\n",
+ request->n_ssids, request->n_channels, request->ie_len);
+
+ priv->scan_channel = 0;
+ queue_delayed_work(priv->work_thread, &priv->scan_work,
+ msecs_to_jiffies(50));
+
+ priv->scan_req = request;
+ priv->internal_scan = internal;
+
+ lbs_deb_leave(LBS_DEB_CFG80211);
+}
+
+static int lbs_cfg_scan(struct wiphy *wiphy,
+ struct net_device *dev,
+ struct cfg80211_scan_request *request)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ int ret = 0;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ if (priv->scan_req || delayed_work_pending(&priv->scan_work)) {
+ /* old scan request not yet processed */
+ ret = -EAGAIN;
+ goto out;
+ }
+
+ _internal_start_scan(priv, false, request);
+
+ if (priv->surpriseremoved)
+ ret = -EIO;
+
+ out:
+ lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
+ return ret;
+}
+
+
+
+
+/***************************************************************************
+ * Events
+ */
+
+void lbs_send_disconnect_notification(struct lbs_private *priv)
+{
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ cfg80211_disconnected(priv->dev,
+ 0,
+ NULL, 0,
+ GFP_KERNEL);
+
+ lbs_deb_leave(LBS_DEB_CFG80211);
+}
+
+void lbs_send_mic_failureevent(struct lbs_private *priv, u32 event)
+{
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ cfg80211_michael_mic_failure(priv->dev,
+ priv->assoc_bss,
+ event == MACREG_INT_CODE_MIC_ERR_MULTICAST ?
+ NL80211_KEYTYPE_GROUP :
+ NL80211_KEYTYPE_PAIRWISE,
+ -1,
+ NULL,
+ GFP_KERNEL);
+
+ lbs_deb_leave(LBS_DEB_CFG80211);
+}
+
+
+
+
+/***************************************************************************
+ * Connect/disconnect
+ */
+
+
+/*
+ * This removes all WEP keys
+ */
+static int lbs_remove_wep_keys(struct lbs_private *priv)
+{
+ struct cmd_ds_802_11_set_wep cmd;
+ int ret;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+ cmd.keyindex = cpu_to_le16(priv->wep_tx_key);
+ cmd.action = cpu_to_le16(CMD_ACT_REMOVE);
+
+ ret = lbs_cmd_with_response(priv, CMD_802_11_SET_WEP, &cmd);
+
+ lbs_deb_leave(LBS_DEB_CFG80211);
+ return ret;
+}
+
+/*
+ * Set WEP keys
+ */
+static int lbs_set_wep_keys(struct lbs_private *priv)
+{
+ struct cmd_ds_802_11_set_wep cmd;
+ int i;
+ int ret;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ /*
+ * command 13 00
+ * size 50 00
+ * sequence xx xx
+ * result 00 00
+ * action 02 00 ACT_ADD
+ * transmit key 00 00
+ * type for key 1 01 WEP40
+ * type for key 2 00
+ * type for key 3 00
+ * type for key 4 00
+ * key 1 39 39 39 39 39 00 00 00
+ * 00 00 00 00 00 00 00 00
+ * key 2 00 00 00 00 00 00 00 00
+ * 00 00 00 00 00 00 00 00
+ * key 3 00 00 00 00 00 00 00 00
+ * 00 00 00 00 00 00 00 00
+ * key 4 00 00 00 00 00 00 00 00
+ */
+ if (priv->wep_key_len[0] || priv->wep_key_len[1] ||
+ priv->wep_key_len[2] || priv->wep_key_len[3]) {
+ /* Only set wep keys if we have at least one of them */
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+ cmd.keyindex = cpu_to_le16(priv->wep_tx_key);
+ cmd.action = cpu_to_le16(CMD_ACT_ADD);
+
+ for (i = 0; i < 4; i++) {
+ switch (priv->wep_key_len[i]) {
+ case WLAN_KEY_LEN_WEP40:
+ cmd.keytype[i] = CMD_TYPE_WEP_40_BIT;
+ break;
+ case WLAN_KEY_LEN_WEP104:
+ cmd.keytype[i] = CMD_TYPE_WEP_104_BIT;
+ break;
+ default:
+ cmd.keytype[i] = 0;
+ break;
+ }
+ memcpy(cmd.keymaterial[i], priv->wep_key[i],
+ priv->wep_key_len[i]);
+ }
+
+ ret = lbs_cmd_with_response(priv, CMD_802_11_SET_WEP, &cmd);
+ } else {
+ /* Otherwise remove all wep keys */
+ ret = lbs_remove_wep_keys(priv);
+ }
+
+ lbs_deb_leave(LBS_DEB_CFG80211);
+ return ret;
+}
+
+
+/*
+ * Enable/Disable RSN status
+ */
+static int lbs_enable_rsn(struct lbs_private *priv, int enable)
+{
+ struct cmd_ds_802_11_enable_rsn cmd;
+ int ret;
+
+ lbs_deb_enter_args(LBS_DEB_CFG80211, "%d", enable);
+
+ /*
+ * cmd 2f 00
+ * size 0c 00
+ * sequence xx xx
+ * result 00 00
+ * action 01 00 ACT_SET
+ * enable 01 00
+ */
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+ cmd.action = cpu_to_le16(CMD_ACT_SET);
+ cmd.enable = cpu_to_le16(enable);
+
+ ret = lbs_cmd_with_response(priv, CMD_802_11_ENABLE_RSN, &cmd);
+
+ lbs_deb_leave(LBS_DEB_CFG80211);
+ return ret;
+}
+
+
+/*
+ * Set WPA/WPA key material
+ */
+
+/* like "struct cmd_ds_802_11_key_material", but with cmd_header. Once we
+ * get rid of WEXT, this should go into host.h */
+
+struct cmd_key_material {
+ struct cmd_header hdr;
+
+ __le16 action;
+ struct MrvlIEtype_keyParamSet param;
+} __packed;
+
+static int lbs_set_key_material(struct lbs_private *priv,
+ int key_type,
+ int key_info,
+ u8 *key, u16 key_len)
+{
+ struct cmd_key_material cmd;
+ int ret;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ /*
+ * Example for WPA (TKIP):
+ *
+ * cmd 5e 00
+ * size 34 00
+ * sequence xx xx
+ * result 00 00
+ * action 01 00
+ * TLV type 00 01 key param
+ * length 00 26
+ * key type 01 00 TKIP
+ * key info 06 00 UNICAST | ENABLED
+ * key len 20 00
+ * key 32 bytes
+ */
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+ cmd.action = cpu_to_le16(CMD_ACT_SET);
+ cmd.param.type = cpu_to_le16(TLV_TYPE_KEY_MATERIAL);
+ cmd.param.length = cpu_to_le16(sizeof(cmd.param) - 4);
+ cmd.param.keytypeid = cpu_to_le16(key_type);
+ cmd.param.keyinfo = cpu_to_le16(key_info);
+ cmd.param.keylen = cpu_to_le16(key_len);
+ if (key && key_len)
+ memcpy(cmd.param.key, key, key_len);
+
+ ret = lbs_cmd_with_response(priv, CMD_802_11_KEY_MATERIAL, &cmd);
+
+ lbs_deb_leave(LBS_DEB_CFG80211);
+ return ret;
+}
+
+
+/*
+ * Sets the auth type (open, shared, etc) in the firmware. That
+ * we use CMD_802_11_AUTHENTICATE is misleading, this firmware
+ * command doesn't send an authentication frame at all, it just
+ * stores the auth_type.
+ */
+static int lbs_set_authtype(struct lbs_private *priv,
+ struct cfg80211_connect_params *sme)
+{
+ struct cmd_ds_802_11_authenticate cmd;
+ int ret;
+
+ lbs_deb_enter_args(LBS_DEB_CFG80211, "%d", sme->auth_type);
+
+ /*
+ * cmd 11 00
+ * size 19 00
+ * sequence xx xx
+ * result 00 00
+ * BSS id 00 13 19 80 da 30
+ * auth type 00
+ * reserved 00 00 00 00 00 00 00 00 00 00
+ */
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+ if (sme->bssid)
+ memcpy(cmd.bssid, sme->bssid, ETH_ALEN);
+ /* convert auth_type */
+ ret = lbs_auth_to_authtype(sme->auth_type);
+ if (ret < 0)
+ goto done;
+
+ cmd.authtype = ret;
+ ret = lbs_cmd_with_response(priv, CMD_802_11_AUTHENTICATE, &cmd);
+
+ done:
+ lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
+ return ret;
+}
+
+
+/*
+ * Create association request
+ */
+#define LBS_ASSOC_MAX_CMD_SIZE \
+ (sizeof(struct cmd_ds_802_11_associate) \
+ - 512 /* cmd_ds_802_11_associate.iebuf */ \
+ + LBS_MAX_SSID_TLV_SIZE \
+ + LBS_MAX_CHANNEL_TLV_SIZE \
+ + LBS_MAX_CF_PARAM_TLV_SIZE \
+ + LBS_MAX_AUTH_TYPE_TLV_SIZE \
+ + LBS_MAX_WPA_TLV_SIZE)
+
+static int lbs_associate(struct lbs_private *priv,
+ struct cfg80211_bss *bss,
+ struct cfg80211_connect_params *sme)
+{
+ struct cmd_ds_802_11_associate_response *resp;
+ struct cmd_ds_802_11_associate *cmd = kzalloc(LBS_ASSOC_MAX_CMD_SIZE,
+ GFP_KERNEL);
+ const u8 *ssid_eid;
+ size_t len, resp_ie_len;
+ int status;
+ int ret;
+ u8 *pos = &(cmd->iebuf[0]);
+ u8 *tmp;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ if (!cmd) {
+ ret = -ENOMEM;
+ goto done;
+ }
+
+ /*
+ * cmd 50 00
+ * length 34 00
+ * sequence xx xx
+ * result 00 00
+ * BSS id 00 13 19 80 da 30
+ * capabilities 11 00
+ * listen interval 0a 00
+ * beacon interval 00 00
+ * DTIM period 00
+ * TLVs xx (up to 512 bytes)
+ */
+ cmd->hdr.command = cpu_to_le16(CMD_802_11_ASSOCIATE);
+
+ /* Fill in static fields */
+ memcpy(cmd->bssid, bss->bssid, ETH_ALEN);
+ cmd->listeninterval = cpu_to_le16(MRVDRV_DEFAULT_LISTEN_INTERVAL);
+ cmd->capability = cpu_to_le16(bss->capability);
+
+ /* add SSID TLV */
+ ssid_eid = ieee80211_bss_get_ie(bss, WLAN_EID_SSID);
+ if (ssid_eid)
+ pos += lbs_add_ssid_tlv(pos, ssid_eid + 2, ssid_eid[1]);
+ else
+ lbs_deb_assoc("no SSID\n");
+
+ /* add DS param TLV */
+ if (bss->channel)
+ pos += lbs_add_channel_tlv(pos, bss->channel->hw_value);
+ else
+ lbs_deb_assoc("no channel\n");
+
+ /* add (empty) CF param TLV */
+ pos += lbs_add_cf_param_tlv(pos);
+
+ /* add rates TLV */
+ tmp = pos + 4; /* skip Marvell IE header */
+ pos += lbs_add_common_rates_tlv(pos, bss);
+ lbs_deb_hex(LBS_DEB_ASSOC, "Common Rates", tmp, pos - tmp);
+
+ /* add auth type TLV */
+ if (MRVL_FW_MAJOR_REV(priv->fwrelease) >= 9)
+ pos += lbs_add_auth_type_tlv(pos, sme->auth_type);
+
+ /* add WPA/WPA2 TLV */
+ if (sme->ie && sme->ie_len)
+ pos += lbs_add_wpa_tlv(pos, sme->ie, sme->ie_len);
+
+ len = (sizeof(*cmd) - sizeof(cmd->iebuf)) +
+ (u16)(pos - (u8 *) &cmd->iebuf);
+ cmd->hdr.size = cpu_to_le16(len);
+
+ lbs_deb_hex(LBS_DEB_ASSOC, "ASSOC_CMD", (u8 *) cmd,
+ le16_to_cpu(cmd->hdr.size));
+
+ /* store for later use */
+ memcpy(priv->assoc_bss, bss->bssid, ETH_ALEN);
+
+ ret = lbs_cmd_with_response(priv, CMD_802_11_ASSOCIATE, cmd);
+ if (ret)
+ goto done;
+
+ /* generate connect message to cfg80211 */
+
+ resp = (void *) cmd; /* recast for easier field access */
+ status = le16_to_cpu(resp->statuscode);
+
+ /* Older FW versions map the IEEE 802.11 Status Code in the association
+ * response to the following values returned in resp->statuscode:
+ *
+ * IEEE Status Code Marvell Status Code
+ * 0 -> 0x0000 ASSOC_RESULT_SUCCESS
+ * 13 -> 0x0004 ASSOC_RESULT_AUTH_REFUSED
+ * 14 -> 0x0004 ASSOC_RESULT_AUTH_REFUSED
+ * 15 -> 0x0004 ASSOC_RESULT_AUTH_REFUSED
+ * 16 -> 0x0004 ASSOC_RESULT_AUTH_REFUSED
+ * others -> 0x0003 ASSOC_RESULT_REFUSED
+ *
+ * Other response codes:
+ * 0x0001 -> ASSOC_RESULT_INVALID_PARAMETERS (unused)
+ * 0x0002 -> ASSOC_RESULT_TIMEOUT (internal timer expired waiting for
+ * association response from the AP)
+ */
+ if (MRVL_FW_MAJOR_REV(priv->fwrelease) <= 8) {
+ switch (status) {
+ case 0:
+ break;
+ case 1:
+ lbs_deb_assoc("invalid association parameters\n");
+ status = WLAN_STATUS_CAPS_UNSUPPORTED;
+ break;
+ case 2:
+ lbs_deb_assoc("timer expired while waiting for AP\n");
+ status = WLAN_STATUS_AUTH_TIMEOUT;
+ break;
+ case 3:
+ lbs_deb_assoc("association refused by AP\n");
+ status = WLAN_STATUS_ASSOC_DENIED_UNSPEC;
+ break;
+ case 4:
+ lbs_deb_assoc("authentication refused by AP\n");
+ status = WLAN_STATUS_UNKNOWN_AUTH_TRANSACTION;
+ break;
+ default:
+ lbs_deb_assoc("association failure %d\n", status);
+ /* v5 OLPC firmware does return the AP status code if
+ * it's not one of the values above. Let that through.
+ */
+ break;
+ }
+ }
+
+ lbs_deb_assoc("status %d, statuscode 0x%04x, capability 0x%04x, "
+ "aid 0x%04x\n", status, le16_to_cpu(resp->statuscode),
+ le16_to_cpu(resp->capability), le16_to_cpu(resp->aid));
+
+ resp_ie_len = le16_to_cpu(resp->hdr.size)
+ - sizeof(resp->hdr)
+ - 6;
+ cfg80211_connect_result(priv->dev,
+ priv->assoc_bss,
+ sme->ie, sme->ie_len,
+ resp->iebuf, resp_ie_len,
+ status,
+ GFP_KERNEL);
+
+ if (status == 0) {
+ /* TODO: get rid of priv->connect_status */
+ priv->connect_status = LBS_CONNECTED;
+ netif_carrier_on(priv->dev);
+ if (!priv->tx_pending_len)
+ netif_tx_wake_all_queues(priv->dev);
+ }
+
+done:
+ lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
+ return ret;
+}
+
+static struct cfg80211_scan_request *
+_new_connect_scan_req(struct wiphy *wiphy, struct cfg80211_connect_params *sme)
+{
+ struct cfg80211_scan_request *creq = NULL;
+ int i, n_channels = 0;
+ enum ieee80211_band band;
+
+ for (band = 0; band < IEEE80211_NUM_BANDS; band++) {
+ if (wiphy->bands[band])
+ n_channels += wiphy->bands[band]->n_channels;
+ }
+
+ creq = kzalloc(sizeof(*creq) + sizeof(struct cfg80211_ssid) +
+ n_channels * sizeof(void *),
+ GFP_ATOMIC);
+ if (!creq)
+ return NULL;
+
+ /* SSIDs come after channels */
+ creq->ssids = (void *)&creq->channels[n_channels];
+ creq->n_channels = n_channels;
+ creq->n_ssids = 1;
+
+ /* Scan all available channels */
+ i = 0;
+ for (band = 0; band < IEEE80211_NUM_BANDS; band++) {
+ int j;
+
+ if (!wiphy->bands[band])
+ continue;
+
+ for (j = 0; j < wiphy->bands[band]->n_channels; j++) {
+ /* ignore disabled channels */
+ if (wiphy->bands[band]->channels[j].flags &
+ IEEE80211_CHAN_DISABLED)
+ continue;
+
+ creq->channels[i] = &wiphy->bands[band]->channels[j];
+ i++;
+ }
+ }
+ if (i) {
+ /* Set real number of channels specified in creq->channels[] */
+ creq->n_channels = i;
+
+ /* Scan for the SSID we're going to connect to */
+ memcpy(creq->ssids[0].ssid, sme->ssid, sme->ssid_len);
+ creq->ssids[0].ssid_len = sme->ssid_len;
+ } else {
+ /* No channels found... */
+ kfree(creq);
+ creq = NULL;
+ }
+
+ return creq;
+}
+
+static int lbs_cfg_connect(struct wiphy *wiphy, struct net_device *dev,
+ struct cfg80211_connect_params *sme)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ struct cfg80211_bss *bss = NULL;
+ int ret = 0;
+ u8 preamble = RADIO_PREAMBLE_SHORT;
- lbs_deb_enter_args(LBS_DEB_CFG80211, "freq %d, type %d", chan->center_freq, channel_type);
+ lbs_deb_enter(LBS_DEB_CFG80211);
- if (channel_type != NL80211_CHAN_NO_HT)
+ if (!sme->bssid) {
+ /* Run a scan if one isn't in-progress already and if the last
+ * scan was done more than 2 seconds ago.
+ */
+ if (priv->scan_req == NULL &&
+ time_after(jiffies, priv->last_scan + (2 * HZ))) {
+ struct cfg80211_scan_request *creq;
+
+ creq = _new_connect_scan_req(wiphy, sme);
+ if (!creq) {
+ ret = -EINVAL;
+ goto done;
+ }
+
+ lbs_deb_assoc("assoc: scanning for compatible AP\n");
+ _internal_start_scan(priv, true, creq);
+ }
+
+ /* Wait for any in-progress scan to complete */
+ lbs_deb_assoc("assoc: waiting for scan to complete\n");
+ wait_event_interruptible_timeout(priv->scan_q,
+ (priv->scan_req == NULL),
+ (15 * HZ));
+ lbs_deb_assoc("assoc: scanning competed\n");
+ }
+
+ /* Find the BSS we want using available scan results */
+ bss = cfg80211_get_bss(wiphy, sme->channel, sme->bssid,
+ sme->ssid, sme->ssid_len,
+ WLAN_CAPABILITY_ESS, WLAN_CAPABILITY_ESS);
+ if (!bss) {
+ lbs_pr_err("assoc: bss %pM not in scan results\n",
+ sme->bssid);
+ ret = -ENOENT;
+ goto done;
+ }
+ lbs_deb_assoc("trying %pM\n", bss->bssid);
+ lbs_deb_assoc("cipher 0x%x, key index %d, key len %d\n",
+ sme->crypto.cipher_group,
+ sme->key_idx, sme->key_len);
+
+ /* As this is a new connection, clear locally stored WEP keys */
+ priv->wep_tx_key = 0;
+ memset(priv->wep_key, 0, sizeof(priv->wep_key));
+ memset(priv->wep_key_len, 0, sizeof(priv->wep_key_len));
+
+ /* set/remove WEP keys */
+ switch (sme->crypto.cipher_group) {
+ case WLAN_CIPHER_SUITE_WEP40:
+ case WLAN_CIPHER_SUITE_WEP104:
+ /* Store provided WEP keys in priv-> */
+ priv->wep_tx_key = sme->key_idx;
+ priv->wep_key_len[sme->key_idx] = sme->key_len;
+ memcpy(priv->wep_key[sme->key_idx], sme->key, sme->key_len);
+ /* Set WEP keys and WEP mode */
+ lbs_set_wep_keys(priv);
+ priv->mac_control |= CMD_ACT_MAC_WEP_ENABLE;
+ lbs_set_mac_control(priv);
+ /* No RSN mode for WEP */
+ lbs_enable_rsn(priv, 0);
+ break;
+ case 0: /* there's no WLAN_CIPHER_SUITE_NONE definition */
+ /*
+ * If we don't have no WEP, no WPA and no WPA2,
+ * we remove all keys like in the WPA/WPA2 setup,
+ * we just don't set RSN.
+ *
+ * Therefore: fall-throught
+ */
+ case WLAN_CIPHER_SUITE_TKIP:
+ case WLAN_CIPHER_SUITE_CCMP:
+ /* Remove WEP keys and WEP mode */
+ lbs_remove_wep_keys(priv);
+ priv->mac_control &= ~CMD_ACT_MAC_WEP_ENABLE;
+ lbs_set_mac_control(priv);
+
+ /* clear the WPA/WPA2 keys */
+ lbs_set_key_material(priv,
+ KEY_TYPE_ID_WEP, /* doesn't matter */
+ KEY_INFO_WPA_UNICAST,
+ NULL, 0);
+ lbs_set_key_material(priv,
+ KEY_TYPE_ID_WEP, /* doesn't matter */
+ KEY_INFO_WPA_MCAST,
+ NULL, 0);
+ /* RSN mode for WPA/WPA2 */
+ lbs_enable_rsn(priv, sme->crypto.cipher_group != 0);
+ break;
+ default:
+ lbs_pr_err("unsupported cipher group 0x%x\n",
+ sme->crypto.cipher_group);
+ ret = -ENOTSUPP;
+ goto done;
+ }
+
+ lbs_set_authtype(priv, sme);
+ lbs_set_radio(priv, preamble, 1);
+
+ /* Do the actual association */
+ ret = lbs_associate(priv, bss, sme);
+
+ done:
+ if (bss)
+ cfg80211_put_bss(bss);
+ lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
+ return ret;
+}
+
+static int lbs_cfg_disconnect(struct wiphy *wiphy, struct net_device *dev,
+ u16 reason_code)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ struct cmd_ds_802_11_deauthenticate cmd;
+
+ lbs_deb_enter_args(LBS_DEB_CFG80211, "reason_code %d", reason_code);
+
+ /* store for lbs_cfg_ret_disconnect() */
+ priv->disassoc_reason = reason_code;
+
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+ /* Mildly ugly to use a locally store my own BSSID ... */
+ memcpy(cmd.macaddr, &priv->assoc_bss, ETH_ALEN);
+ cmd.reasoncode = cpu_to_le16(reason_code);
+
+ if (lbs_cmd_with_response(priv, CMD_802_11_DEAUTHENTICATE, &cmd))
+ return -EFAULT;
+
+ cfg80211_disconnected(priv->dev,
+ priv->disassoc_reason,
+ NULL, 0,
+ GFP_KERNEL);
+ priv->connect_status = LBS_DISCONNECTED;
+
+ return 0;
+}
+
+
+static int lbs_cfg_set_default_key(struct wiphy *wiphy,
+ struct net_device *netdev,
+ u8 key_index)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ if (key_index != priv->wep_tx_key) {
+ lbs_deb_assoc("set_default_key: to %d\n", key_index);
+ priv->wep_tx_key = key_index;
+ lbs_set_wep_keys(priv);
+ }
+
+ return 0;
+}
+
+
+static int lbs_cfg_add_key(struct wiphy *wiphy, struct net_device *netdev,
+ u8 idx, bool pairwise, const u8 *mac_addr,
+ struct key_params *params)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ u16 key_info;
+ u16 key_type;
+ int ret = 0;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ lbs_deb_assoc("add_key: cipher 0x%x, mac_addr %pM\n",
+ params->cipher, mac_addr);
+ lbs_deb_assoc("add_key: key index %d, key len %d\n",
+ idx, params->key_len);
+ if (params->key_len)
+ lbs_deb_hex(LBS_DEB_CFG80211, "KEY",
+ params->key, params->key_len);
+
+ lbs_deb_assoc("add_key: seq len %d\n", params->seq_len);
+ if (params->seq_len)
+ lbs_deb_hex(LBS_DEB_CFG80211, "SEQ",
+ params->seq, params->seq_len);
+
+ switch (params->cipher) {
+ case WLAN_CIPHER_SUITE_WEP40:
+ case WLAN_CIPHER_SUITE_WEP104:
+ /* actually compare if something has changed ... */
+ if ((priv->wep_key_len[idx] != params->key_len) ||
+ memcmp(priv->wep_key[idx],
+ params->key, params->key_len) != 0) {
+ priv->wep_key_len[idx] = params->key_len;
+ memcpy(priv->wep_key[idx],
+ params->key, params->key_len);
+ lbs_set_wep_keys(priv);
+ }
+ break;
+ case WLAN_CIPHER_SUITE_TKIP:
+ case WLAN_CIPHER_SUITE_CCMP:
+ key_info = KEY_INFO_WPA_ENABLED | ((idx == 0)
+ ? KEY_INFO_WPA_UNICAST
+ : KEY_INFO_WPA_MCAST);
+ key_type = (params->cipher == WLAN_CIPHER_SUITE_TKIP)
+ ? KEY_TYPE_ID_TKIP
+ : KEY_TYPE_ID_AES;
+ lbs_set_key_material(priv,
+ key_type,
+ key_info,
+ params->key, params->key_len);
+ break;
+ default:
+ lbs_pr_err("unhandled cipher 0x%x\n", params->cipher);
+ ret = -ENOTSUPP;
+ break;
+ }
+
+ return ret;
+}
+
+
+static int lbs_cfg_del_key(struct wiphy *wiphy, struct net_device *netdev,
+ u8 key_index, bool pairwise, const u8 *mac_addr)
+{
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ lbs_deb_assoc("del_key: key_idx %d, mac_addr %pM\n",
+ key_index, mac_addr);
+
+#ifdef TODO
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ /*
+ * I think can keep this a NO-OP, because:
+
+ * - we clear all keys whenever we do lbs_cfg_connect() anyway
+ * - neither "iw" nor "wpa_supplicant" won't call this during
+ * an ongoing connection
+ * - TODO: but I have to check if this is still true when
+ * I set the AP to periodic re-keying
+ * - we've not kzallec() something when we've added a key at
+ * lbs_cfg_connect() or lbs_cfg_add_key().
+ *
+ * This causes lbs_cfg_del_key() only called at disconnect time,
+ * where we'd just waste time deleting a key that is not going
+ * to be used anyway.
+ */
+ if (key_index < 3 && priv->wep_key_len[key_index]) {
+ priv->wep_key_len[key_index] = 0;
+ lbs_set_wep_keys(priv);
+ }
+#endif
+
+ return 0;
+}
+
+
+/***************************************************************************
+ * Get station
+ */
+
+static int lbs_cfg_get_station(struct wiphy *wiphy, struct net_device *dev,
+ u8 *mac, struct station_info *sinfo)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ s8 signal, noise;
+ int ret;
+ size_t i;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ sinfo->filled |= STATION_INFO_TX_BYTES |
+ STATION_INFO_TX_PACKETS |
+ STATION_INFO_RX_BYTES |
+ STATION_INFO_RX_PACKETS;
+ sinfo->tx_bytes = priv->dev->stats.tx_bytes;
+ sinfo->tx_packets = priv->dev->stats.tx_packets;
+ sinfo->rx_bytes = priv->dev->stats.rx_bytes;
+ sinfo->rx_packets = priv->dev->stats.rx_packets;
+
+ /* Get current RSSI */
+ ret = lbs_get_rssi(priv, &signal, &noise);
+ if (ret == 0) {
+ sinfo->signal = signal;
+ sinfo->filled |= STATION_INFO_SIGNAL;
+ }
+
+ /* Convert priv->cur_rate from hw_value to NL80211 value */
+ for (i = 0; i < ARRAY_SIZE(lbs_rates); i++) {
+ if (priv->cur_rate == lbs_rates[i].hw_value) {
+ sinfo->txrate.legacy = lbs_rates[i].bitrate;
+ sinfo->filled |= STATION_INFO_TX_BITRATE;
+ break;
+ }
+ }
+
+ return 0;
+}
+
+
+
+
+/***************************************************************************
+ * "Site survey", here just current channel and noise level
+ */
+
+static int lbs_get_survey(struct wiphy *wiphy, struct net_device *dev,
+ int idx, struct survey_info *survey)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ s8 signal, noise;
+ int ret;
+
+ if (idx != 0)
+ ret = -ENOENT;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ survey->channel = ieee80211_get_channel(wiphy,
+ ieee80211_channel_to_frequency(priv->channel));
+
+ ret = lbs_get_rssi(priv, &signal, &noise);
+ if (ret == 0) {
+ survey->filled = SURVEY_INFO_NOISE_DBM;
+ survey->noise = noise;
+ }
+
+ lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
+ return ret;
+}
+
+
+
+
+/***************************************************************************
+ * Change interface
+ */
+
+static int lbs_change_intf(struct wiphy *wiphy, struct net_device *dev,
+ enum nl80211_iftype type, u32 *flags,
+ struct vif_params *params)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ int ret = 0;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ switch (type) {
+ case NL80211_IFTYPE_MONITOR:
+ ret = lbs_set_monitor_mode(priv, 1);
+ break;
+ case NL80211_IFTYPE_STATION:
+ if (priv->wdev->iftype == NL80211_IFTYPE_MONITOR)
+ ret = lbs_set_monitor_mode(priv, 0);
+ if (!ret)
+ ret = lbs_set_snmp_mib(priv, SNMP_MIB_OID_BSS_TYPE, 1);
+ break;
+ case NL80211_IFTYPE_ADHOC:
+ if (priv->wdev->iftype == NL80211_IFTYPE_MONITOR)
+ ret = lbs_set_monitor_mode(priv, 0);
+ if (!ret)
+ ret = lbs_set_snmp_mib(priv, SNMP_MIB_OID_BSS_TYPE, 2);
+ break;
+ default:
+ ret = -ENOTSUPP;
+ }
+
+ if (!ret)
+ priv->wdev->iftype = type;
+
+ lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
+ return ret;
+}
+
+
+
+/***************************************************************************
+ * IBSS (Ad-Hoc)
+ */
+
+/* The firmware needs the following bits masked out of the beacon-derived
+ * capability field when associating/joining to a BSS:
+ * 9 (QoS), 11 (APSD), 12 (unused), 14 (unused), 15 (unused)
+ */
+#define CAPINFO_MASK (~(0xda00))
+
+
+static void lbs_join_post(struct lbs_private *priv,
+ struct cfg80211_ibss_params *params,
+ u8 *bssid, u16 capability)
+{
+ u8 fake_ie[2 + IEEE80211_MAX_SSID_LEN + /* ssid */
+ 2 + 4 + /* basic rates */
+ 2 + 1 + /* DS parameter */
+ 2 + 2 + /* atim */
+ 2 + 8]; /* extended rates */
+ u8 *fake = fake_ie;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ /*
+ * For cfg80211_inform_bss, we'll need a fake IE, as we can't get
+ * the real IE from the firmware. So we fabricate a fake IE based on
+ * what the firmware actually sends (sniffed with wireshark).
+ */
+ /* Fake SSID IE */
+ *fake++ = WLAN_EID_SSID;
+ *fake++ = params->ssid_len;
+ memcpy(fake, params->ssid, params->ssid_len);
+ fake += params->ssid_len;
+ /* Fake supported basic rates IE */
+ *fake++ = WLAN_EID_SUPP_RATES;
+ *fake++ = 4;
+ *fake++ = 0x82;
+ *fake++ = 0x84;
+ *fake++ = 0x8b;
+ *fake++ = 0x96;
+ /* Fake DS channel IE */
+ *fake++ = WLAN_EID_DS_PARAMS;
+ *fake++ = 1;
+ *fake++ = params->channel->hw_value;
+ /* Fake IBSS params IE */
+ *fake++ = WLAN_EID_IBSS_PARAMS;
+ *fake++ = 2;
+ *fake++ = 0; /* ATIM=0 */
+ *fake++ = 0;
+ /* Fake extended rates IE, TODO: don't add this for 802.11b only,
+ * but I don't know how this could be checked */
+ *fake++ = WLAN_EID_EXT_SUPP_RATES;
+ *fake++ = 8;
+ *fake++ = 0x0c;
+ *fake++ = 0x12;
+ *fake++ = 0x18;
+ *fake++ = 0x24;
+ *fake++ = 0x30;
+ *fake++ = 0x48;
+ *fake++ = 0x60;
+ *fake++ = 0x6c;
+ lbs_deb_hex(LBS_DEB_CFG80211, "IE", fake_ie, fake - fake_ie);
+
+ cfg80211_inform_bss(priv->wdev->wiphy,
+ params->channel,
+ bssid,
+ 0,
+ capability,
+ params->beacon_interval,
+ fake_ie, fake - fake_ie,
+ 0, GFP_KERNEL);
+
+ memcpy(priv->wdev->ssid, params->ssid, params->ssid_len);
+ priv->wdev->ssid_len = params->ssid_len;
+
+ cfg80211_ibss_joined(priv->dev, bssid, GFP_KERNEL);
+
+ /* TODO: consider doing this at MACREG_INT_CODE_LINK_SENSED time */
+ priv->connect_status = LBS_CONNECTED;
+ netif_carrier_on(priv->dev);
+ if (!priv->tx_pending_len)
+ netif_wake_queue(priv->dev);
+
+ lbs_deb_leave(LBS_DEB_CFG80211);
+}
+
+static int lbs_ibss_join_existing(struct lbs_private *priv,
+ struct cfg80211_ibss_params *params,
+ struct cfg80211_bss *bss)
+{
+ const u8 *rates_eid = ieee80211_bss_get_ie(bss, WLAN_EID_SUPP_RATES);
+ struct cmd_ds_802_11_ad_hoc_join cmd;
+ u8 preamble = RADIO_PREAMBLE_SHORT;
+ int ret = 0;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ /* TODO: set preamble based on scan result */
+ ret = lbs_set_radio(priv, preamble, 1);
+ if (ret)
+ goto out;
+
+ /*
+ * Example CMD_802_11_AD_HOC_JOIN command:
+ *
+ * command 2c 00 CMD_802_11_AD_HOC_JOIN
+ * size 65 00
+ * sequence xx xx
+ * result 00 00
+ * bssid 02 27 27 97 2f 96
+ * ssid 49 42 53 53 00 00 00 00
+ * 00 00 00 00 00 00 00 00
+ * 00 00 00 00 00 00 00 00
+ * 00 00 00 00 00 00 00 00
+ * type 02 CMD_BSS_TYPE_IBSS
+ * beacon period 64 00
+ * dtim period 00
+ * timestamp 00 00 00 00 00 00 00 00
+ * localtime 00 00 00 00 00 00 00 00
+ * IE DS 03
+ * IE DS len 01
+ * IE DS channel 01
+ * reserveed 00 00 00 00
+ * IE IBSS 06
+ * IE IBSS len 02
+ * IE IBSS atim 00 00
+ * reserved 00 00 00 00
+ * capability 02 00
+ * rates 82 84 8b 96 0c 12 18 24 30 48 60 6c 00
+ * fail timeout ff 00
+ * probe delay 00 00
+ */
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+
+ memcpy(cmd.bss.bssid, bss->bssid, ETH_ALEN);
+ memcpy(cmd.bss.ssid, params->ssid, params->ssid_len);
+ cmd.bss.type = CMD_BSS_TYPE_IBSS;
+ cmd.bss.beaconperiod = cpu_to_le16(params->beacon_interval);
+ cmd.bss.ds.header.id = WLAN_EID_DS_PARAMS;
+ cmd.bss.ds.header.len = 1;
+ cmd.bss.ds.channel = params->channel->hw_value;
+ cmd.bss.ibss.header.id = WLAN_EID_IBSS_PARAMS;
+ cmd.bss.ibss.header.len = 2;
+ cmd.bss.ibss.atimwindow = 0;
+ cmd.bss.capability = cpu_to_le16(bss->capability & CAPINFO_MASK);
+
+ /* set rates to the intersection of our rates and the rates in the
+ bss */
+ if (!rates_eid) {
+ lbs_add_rates(cmd.bss.rates);
+ } else {
+ int hw, i;
+ u8 rates_max = rates_eid[1];
+ u8 *rates = cmd.bss.rates;
+ for (hw = 0; hw < ARRAY_SIZE(lbs_rates); hw++) {
+ u8 hw_rate = lbs_rates[hw].bitrate / 5;
+ for (i = 0; i < rates_max; i++) {
+ if (hw_rate == (rates_eid[i+2] & 0x7f)) {
+ u8 rate = rates_eid[i+2];
+ if (rate == 0x02 || rate == 0x04 ||
+ rate == 0x0b || rate == 0x16)
+ rate |= 0x80;
+ *rates++ = rate;
+ }
+ }
+ }
+ }
+
+ /* Only v8 and below support setting this */
+ if (MRVL_FW_MAJOR_REV(priv->fwrelease) <= 8) {
+ cmd.failtimeout = cpu_to_le16(MRVDRV_ASSOCIATION_TIME_OUT);
+ cmd.probedelay = cpu_to_le16(CMD_SCAN_PROBE_DELAY_TIME);
+ }
+ ret = lbs_cmd_with_response(priv, CMD_802_11_AD_HOC_JOIN, &cmd);
+ if (ret)
+ goto out;
+
+ /*
+ * This is a sample response to CMD_802_11_AD_HOC_JOIN:
+ *
+ * response 2c 80
+ * size 09 00
+ * sequence xx xx
+ * result 00 00
+ * reserved 00
+ */
+ lbs_join_post(priv, params, bss->bssid, bss->capability);
+
+ out:
+ lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
+ return ret;
+}
+
+
+
+static int lbs_ibss_start_new(struct lbs_private *priv,
+ struct cfg80211_ibss_params *params)
+{
+ struct cmd_ds_802_11_ad_hoc_start cmd;
+ struct cmd_ds_802_11_ad_hoc_result *resp =
+ (struct cmd_ds_802_11_ad_hoc_result *) &cmd;
+ u8 preamble = RADIO_PREAMBLE_SHORT;
+ int ret = 0;
+ u16 capability;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ ret = lbs_set_radio(priv, preamble, 1);
+ if (ret)
+ goto out;
+
+ /*
+ * Example CMD_802_11_AD_HOC_START command:
+ *
+ * command 2b 00 CMD_802_11_AD_HOC_START
+ * size b1 00
+ * sequence xx xx
+ * result 00 00
+ * ssid 54 45 53 54 00 00 00 00
+ * 00 00 00 00 00 00 00 00
+ * 00 00 00 00 00 00 00 00
+ * 00 00 00 00 00 00 00 00
+ * bss type 02
+ * beacon period 64 00
+ * dtim period 00
+ * IE IBSS 06
+ * IE IBSS len 02
+ * IE IBSS atim 00 00
+ * reserved 00 00 00 00
+ * IE DS 03
+ * IE DS len 01
+ * IE DS channel 01
+ * reserved 00 00 00 00
+ * probe delay 00 00
+ * capability 02 00
+ * rates 82 84 8b 96 (basic rates with have bit 7 set)
+ * 0c 12 18 24 30 48 60 6c
+ * padding 100 bytes
+ */
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+ memcpy(cmd.ssid, params->ssid, params->ssid_len);
+ cmd.bsstype = CMD_BSS_TYPE_IBSS;
+ cmd.beaconperiod = cpu_to_le16(params->beacon_interval);
+ cmd.ibss.header.id = WLAN_EID_IBSS_PARAMS;
+ cmd.ibss.header.len = 2;
+ cmd.ibss.atimwindow = 0;
+ cmd.ds.header.id = WLAN_EID_DS_PARAMS;
+ cmd.ds.header.len = 1;
+ cmd.ds.channel = params->channel->hw_value;
+ /* Only v8 and below support setting probe delay */
+ if (MRVL_FW_MAJOR_REV(priv->fwrelease) <= 8)
+ cmd.probedelay = cpu_to_le16(CMD_SCAN_PROBE_DELAY_TIME);
+ /* TODO: mix in WLAN_CAPABILITY_PRIVACY */
+ capability = WLAN_CAPABILITY_IBSS;
+ cmd.capability = cpu_to_le16(capability);
+ lbs_add_rates(cmd.rates);
+
+
+ ret = lbs_cmd_with_response(priv, CMD_802_11_AD_HOC_START, &cmd);
+ if (ret)
goto out;
- ret = lbs_set_channel(priv, chan->hw_value);
+ /*
+ * This is a sample response to CMD_802_11_AD_HOC_JOIN:
+ *
+ * response 2b 80
+ * size 14 00
+ * sequence xx xx
+ * result 00 00
+ * reserved 00
+ * bssid 02 2b 7b 0f 86 0e
+ */
+ lbs_join_post(priv, params, resp->bssid, capability);
+
+ out:
+ lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
+ return ret;
+}
+
+
+static int lbs_join_ibss(struct wiphy *wiphy, struct net_device *dev,
+ struct cfg80211_ibss_params *params)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ int ret = 0;
+ struct cfg80211_bss *bss;
+ DECLARE_SSID_BUF(ssid_buf);
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ if (!params->channel) {
+ ret = -ENOTSUPP;
+ goto out;
+ }
+
+ ret = lbs_set_channel(priv, params->channel->hw_value);
+ if (ret)
+ goto out;
+
+ /* Search if someone is beaconing. This assumes that the
+ * bss list is populated already */
+ bss = cfg80211_get_bss(wiphy, params->channel, params->bssid,
+ params->ssid, params->ssid_len,
+ WLAN_CAPABILITY_IBSS, WLAN_CAPABILITY_IBSS);
+
+ if (bss) {
+ ret = lbs_ibss_join_existing(priv, params, bss);
+ cfg80211_put_bss(bss);
+ } else
+ ret = lbs_ibss_start_new(priv, params);
+
out:
lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
}
+static int lbs_leave_ibss(struct wiphy *wiphy, struct net_device *dev)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ struct cmd_ds_802_11_ad_hoc_stop cmd;
+ int ret = 0;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ memset(&cmd, 0, sizeof(cmd));
+ cmd.hdr.size = cpu_to_le16(sizeof(cmd));
+ ret = lbs_cmd_with_response(priv, CMD_802_11_AD_HOC_STOP, &cmd);
+
+ /* TODO: consider doing this at MACREG_INT_CODE_ADHOC_BCN_LOST time */
+ lbs_mac_event_disconnected(priv);
+
+ lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
+ return ret;
+}
+
+
+/***************************************************************************
+ * Initialization
+ */
+
static struct cfg80211_ops lbs_cfg80211_ops = {
.set_channel = lbs_cfg_set_channel,
+ .scan = lbs_cfg_scan,
+ .connect = lbs_cfg_connect,
+ .disconnect = lbs_cfg_disconnect,
+ .add_key = lbs_cfg_add_key,
+ .del_key = lbs_cfg_del_key,
+ .set_default_key = lbs_cfg_set_default_key,
+ .get_station = lbs_cfg_get_station,
+ .dump_survey = lbs_get_survey,
+ .change_virtual_intf = lbs_change_intf,
+ .join_ibss = lbs_join_ibss,
+ .leave_ibss = lbs_leave_ibss,
};
}
+static void lbs_cfg_set_regulatory_hint(struct lbs_private *priv)
+{
+ struct region_code_mapping {
+ const char *cn;
+ int code;
+ };
+
+ /* Section 5.17.2 */
+ static struct region_code_mapping regmap[] = {
+ {"US ", 0x10}, /* US FCC */
+ {"CA ", 0x20}, /* Canada */
+ {"EU ", 0x30}, /* ETSI */
+ {"ES ", 0x31}, /* Spain */
+ {"FR ", 0x32}, /* France */
+ {"JP ", 0x40}, /* Japan */
+ };
+ size_t i;
+
+ lbs_deb_enter(LBS_DEB_CFG80211);
+
+ for (i = 0; i < ARRAY_SIZE(regmap); i++)
+ if (regmap[i].code == priv->regioncode) {
+ regulatory_hint(priv->wdev->wiphy, regmap[i].cn);
+ break;
+ }
+
+ lbs_deb_leave(LBS_DEB_CFG80211);
+}
+
+
/*
* This function get's called after lbs_setup_firmware() determined the
* firmware capabities. So we can setup the wiphy according to our
wdev->wiphy->max_scan_ssids = 1;
wdev->wiphy->signal_type = CFG80211_SIGNAL_TYPE_MBM;
- /* TODO: BIT(NL80211_IFTYPE_ADHOC); */
- wdev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION);
+ wdev->wiphy->interface_modes =
+ BIT(NL80211_IFTYPE_STATION) |
+ BIT(NL80211_IFTYPE_ADHOC);
+ if (lbs_rtap_supported(priv))
+ wdev->wiphy->interface_modes |= BIT(NL80211_IFTYPE_MONITOR);
- /* TODO: honor priv->regioncode */
wdev->wiphy->bands[IEEE80211_BAND_2GHZ] = &lbs_band_2ghz;
/*
*/
wdev->wiphy->cipher_suites = cipher_suites;
wdev->wiphy->n_cipher_suites = ARRAY_SIZE(cipher_suites);
+ wdev->wiphy->reg_notifier = lbs_reg_notifier;
ret = wiphy_register(wdev->wiphy);
if (ret < 0)
if (ret)
lbs_pr_err("cannot register network device\n");
+ INIT_DELAYED_WORK(&priv->scan_work, lbs_scan_worker);
+
+ lbs_cfg_set_regulatory_hint(priv);
+
lbs_deb_leave_args(LBS_DEB_CFG80211, "ret %d", ret);
return ret;
}
+int lbs_reg_notifier(struct wiphy *wiphy,
+ struct regulatory_request *request)
+{
+ struct lbs_private *priv = wiphy_priv(wiphy);
+ int ret;
+
+ lbs_deb_enter_args(LBS_DEB_CFG80211, "cfg80211 regulatory domain "
+ "callback for domain %c%c\n", request->alpha2[0],
+ request->alpha2[1]);
+
+ ret = lbs_set_11d_domain_info(priv, request, wiphy->bands);
+
+ lbs_deb_leave(LBS_DEB_CFG80211);
+ return ret;
+}
+
+void lbs_scan_deinit(struct lbs_private *priv)
+{
+ lbs_deb_enter(LBS_DEB_CFG80211);
+ cancel_delayed_work_sync(&priv->scan_work);
+}
+
void lbs_cfg_free(struct lbs_private *priv)
{
git.openpandora.org / pandora-kernel.git / blobdiff